The microstructure, microhardness and tensile properties of laser additive manufactured (LAM) Ti?5Al?2Sn?2Zr?4Mo?4Cr alloy were investigated. The result shows that the microstructure evolution is strongly affected by ...The microstructure, microhardness and tensile properties of laser additive manufactured (LAM) Ti?5Al?2Sn?2Zr?4Mo?4Cr alloy were investigated. The result shows that the microstructure evolution is strongly affected by the thermal history of LAM process. Primary α (αp) with different morphologies, secondary α (αs) and martensite α' can be observed at different positions of the LAMed specimen. Annealing treatment can promote the precipitation of rib-like α phase or acicular α phase. As a result, it can increase or decrease the microhardness. The as-deposited L-direction and T-direction specimens contain the same phase constituent with different morphologies. The tensile properties of the as-deposited LAMed specimens are characterized of anisotropy. The L-direction specimen shows the character of low strength but high ductility when compared with the T-direction specimen. After annealing treatment, the strength of L-direction specimen increases significantly while the ductility reduces. The strength of the annealed T-direction specimen changes little, however, the ductility reduces nearly by 50%.展开更多
Split Hopkinson pressure bar test system was used to investigate the plastic deformation behavior and dynamic response character of a-type Ti–5Al–2.5Sn ELI and near a-type Ti–8Al–1Mo–1V titanium alloy when subjec...Split Hopkinson pressure bar test system was used to investigate the plastic deformation behavior and dynamic response character of a-type Ti–5Al–2.5Sn ELI and near a-type Ti–8Al–1Mo–1V titanium alloy when subjected to dynamic loading. In the present work, stress–strain curves at strain rate from 1.5 9 103to 5.0 9 103s-1were analyzed, and optical microscope（OM） was used to reveal adiabatic shearing behavior of recovered samples. Results show that both the two alloys manifest significant strain hardening effects. Critical damage strain rate of the two alloys is about 4.3 9 103s-1, under which the impact absorbs energy of Ti–5Al–2.5Sn ELI and Ti–8Al–1Mo–1V are 560 and 470 MJ m-3, respectively. Both of them fracture along the maximum shearing strength orientation, an angle of 45° to the compression axis. No adiabatic shear band（ASB） is found in Ti–5Al–2.5Sn ELI alloy, whereas several ASBs with different widths exist without regular direction in Ti–8Al–1Mo–1V alloy.展开更多
The mechanical properties and deformation behavior of Ti 5Al 2.5 ZrELI alloy compared with Ti 5Al 2.5 SnELI at 4.2?K, 20?K and 293?K were investigated. The results show that the new titanium alloy Ti 5Al 2.5ZrELI has ...The mechanical properties and deformation behavior of Ti 5Al 2.5 ZrELI alloy compared with Ti 5Al 2.5 SnELI at 4.2?K, 20?K and 293?K were investigated. The results show that the new titanium alloy Ti 5Al 2.5ZrELI has more consistent properties because of its uniform microstructure and less segregation. It has good elongation and ductility. The fracture surfaces are covered with elongated dimples at cryogenic temperatures. The deformation mode at 293?K, 20?K and 4.2?K are twinning and slipping. [展开更多
The characteristics of fatigue crack initiation in Ti-5AI-4Sn-2Zr1Mo-O.7Nd-O.25Si alloy wereStudied. Two modes Of fatigue crack initiation were found. The Nd-rich phase particles displaybetter resistance to fatigue cr...The characteristics of fatigue crack initiation in Ti-5AI-4Sn-2Zr1Mo-O.7Nd-O.25Si alloy wereStudied. Two modes Of fatigue crack initiation were found. The Nd-rich phase particles displaybetter resistance to fatigue crack initiation than the matrix at lower stress.展开更多
基金Projects(51105311,51475380)supported by the National Natural Science Foundation of ChinaProject(2013AA031103)supported by the National High-Tech Research and Development Program of China
文摘The microstructure, microhardness and tensile properties of laser additive manufactured (LAM) Ti?5Al?2Sn?2Zr?4Mo?4Cr alloy were investigated. The result shows that the microstructure evolution is strongly affected by the thermal history of LAM process. Primary α (αp) with different morphologies, secondary α (αs) and martensite α' can be observed at different positions of the LAMed specimen. Annealing treatment can promote the precipitation of rib-like α phase or acicular α phase. As a result, it can increase or decrease the microhardness. The as-deposited L-direction and T-direction specimens contain the same phase constituent with different morphologies. The tensile properties of the as-deposited LAMed specimens are characterized of anisotropy. The L-direction specimen shows the character of low strength but high ductility when compared with the T-direction specimen. After annealing treatment, the strength of L-direction specimen increases significantly while the ductility reduces. The strength of the annealed T-direction specimen changes little, however, the ductility reduces nearly by 50%.
基金financially supported by the Ministry of Science and Technology of China (No. 2012DFG51540)
文摘Split Hopkinson pressure bar test system was used to investigate the plastic deformation behavior and dynamic response character of a-type Ti–5Al–2.5Sn ELI and near a-type Ti–8Al–1Mo–1V titanium alloy when subjected to dynamic loading. In the present work, stress–strain curves at strain rate from 1.5 9 103to 5.0 9 103s-1were analyzed, and optical microscope（OM） was used to reveal adiabatic shearing behavior of recovered samples. Results show that both the two alloys manifest significant strain hardening effects. Critical damage strain rate of the two alloys is about 4.3 9 103s-1, under which the impact absorbs energy of Ti–5Al–2.5Sn ELI and Ti–8Al–1Mo–1V are 560 and 470 MJ m-3, respectively. Both of them fracture along the maximum shearing strength orientation, an angle of 45° to the compression axis. No adiabatic shear band（ASB） is found in Ti–5Al–2.5Sn ELI alloy, whereas several ASBs with different widths exist without regular direction in Ti–8Al–1Mo–1V alloy.
文摘The mechanical properties and deformation behavior of Ti 5Al 2.5 ZrELI alloy compared with Ti 5Al 2.5 SnELI at 4.2?K, 20?K and 293?K were investigated. The results show that the new titanium alloy Ti 5Al 2.5ZrELI has more consistent properties because of its uniform microstructure and less segregation. It has good elongation and ductility. The fracture surfaces are covered with elongated dimples at cryogenic temperatures. The deformation mode at 293?K, 20?K and 4.2?K are twinning and slipping. [
文摘The characteristics of fatigue crack initiation in Ti-5AI-4Sn-2Zr1Mo-O.7Nd-O.25Si alloy wereStudied. Two modes Of fatigue crack initiation were found. The Nd-rich phase particles displaybetter resistance to fatigue crack initiation than the matrix at lower stress.
