Al/α-PbO2/β-PbO2 composite electrodes doped with rare earth oxide （CeO2） were prepared by anodic oxidation method investigate the influence of nano-CeO2 dopants on the properties of Al/α-PbO2/β-PbO2-CeO2 electro...Al/α-PbO2/β-PbO2 composite electrodes doped with rare earth oxide （CeO2） were prepared by anodic oxidation method investigate the influence of nano-CeO2 dopants on the properties of Al/α-PbO2/β-PbO2-CeO2 electrodes and the impact of α-PbO2 as the intermediate layer. The results show that using α-PbO2 as the intermediate layer will benefit the crystallization of β-PbO2 and β-PbO2 is more suitable as the surface layer than α-PbO2. CeO2 dopants change the crystallite size and crystal structure, enhance the catalytic activity, and even change the deposition mechanism of PbO2. The doping of CeO2 in the PbO2 electrodes can enhance the electro-catalytic activity, which is helpful for oxygen evolution, and therefore reduce the cell voltage.展开更多
Al/conductive coating/α-Pb O2-Ce O2-Ti O2/β-PbO 2-MnO 2-WC-Zr O2 composite electrode material was prepared on Al/conductive coating/α-PbO 2-Ce O2-Ti O2 substrate by electrochemical oxidation co-deposition technique...Al/conductive coating/α-Pb O2-Ce O2-Ti O2/β-PbO 2-MnO 2-WC-Zr O2 composite electrode material was prepared on Al/conductive coating/α-PbO 2-Ce O2-Ti O2 substrate by electrochemical oxidation co-deposition technique. The effects of current density on the chemical composition, electrocatalytic activity, and stability of the composite anode material were investigated by energy dispersive X-ray spectroscopy（EDXS）, anode polarization curves, quasi-stationary polarization（Tafel） curves, electrochemical impedance spectroscopy（EIS）, scanning electron microscopy（SEM）, and X-ray diffraction（XRD）. Results reveal that the composite electrode obtained at 1 A/dm2 possesses the lowest overpotential（0.610 V at 500 A/m2） for oxygen evolution, the best electrocatalytic activity, the longest service life（360 h at 40 °C in 150 g/L H2SO4 solution under 2 A/cm2）, and the lowest cell voltage（2.75 V at 500 A/m2）. Furthermore, with increasing current density, the coating exhibits grain growth and the decrease of content of Mn O2. Only a slight effect on crystalline structure is observed.展开更多
β-PbO2 electrodes were prepared by electro-deposition and characterized by scanning electron microscopy,X-ray diffraction,X-ray photoelectron spectroscopy,and linear sweep voltammetry.We confirmed pure β-PbO2 crysta...β-PbO2 electrodes were prepared by electro-deposition and characterized by scanning electron microscopy,X-ray diffraction,X-ray photoelectron spectroscopy,and linear sweep voltammetry.We confirmed pure β-PbO2 crystals were on the electrode and it had a high oxygen evolution potential.The photoactivity and photoelectrochemical（PEC） properties of the β-PbO2 electrode were investigated under visible light irradiation（λ 〉 420 nm） for the decolorization of Methylene Blue.Pseudo first-order kinetics parameter（Kapp） for dye decolorization using the β-PbO2 electrode achieved 6.71×10-4 min-1 under visible light irradiation,which indicated its excellent visible light-induced photoactivity.The Kapp of the PEC process was as much as 1.41×10-3 min-1 and was 1.71 times that of visible light irradiation or electrolysis even in the presence of the β-PbO2 electrode.A significant synergetic effect was observed in the PEC system.We also employed TiO2 modified β-PbO2 electrodes in this test,which revealed that the TiO2 immobilized on the β-PbO2 electrode inhibited the visible light-induced PEC efficiency despite the amount of TiO2 used for electrode preparation.The β-PbO2 electrode was also superior to the dimensionally stable anode（Ti/Ru0.3Ti0.7O2） in visible light-induced photoactivity and PEC efficiency.展开更多
A novel nano crystalline Ag2O2-PbO2 film chemically modified electrode (CME) was prepared and the CME was characterized by X-ray diffractometer (XRD) and atomic force microscope (AFM). By chronoamperometry, the nano A...A novel nano crystalline Ag2O2-PbO2 film chemically modified electrode (CME) was prepared and the CME was characterized by X-ray diffractometer (XRD) and atomic force microscope (AFM). By chronoamperometry, the nano Ag2O2-PbO2 CME was used as bioelectro- chemical sensor to determine the population of Escherichia coli (E. coli) in water. Compared with conventional methods, it is found that the technique we used is fast and convenient in counting E. coli.展开更多
Electrochemical oxidation of aniline in aqueous solution was investigated over a novel Ti/TiOxHy/Sb-SnO2 electrode prepared by the electrodeposition method.Scanning electron microscopy,X-ray diffraction,and electroche...Electrochemical oxidation of aniline in aqueous solution was investigated over a novel Ti/TiOxHy/Sb-SnO2 electrode prepared by the electrodeposition method.Scanning electron microscopy,X-ray diffraction,and electrochemical measurements were used to characterize its morphology,crystal structure,and electrochemical properties.Removal of aniline by the Ti/TiOxHy/Sb-SnO2electrode was investigated by ultraviolet-Visible spectroscopy and chemical oxygen demand（COD）analysis under different conditions,including current densities,initial concentrations of aniline,pH values,concentrations of chloride ions,and types of reactor.It was found that a higher current density,a lower initial concentration of aniline,an acidic solution,the presence of chloride ions（0.2wt%NaCl）,and a three-dimensional（3D） reactor promoted the removal efficiency of aniline.Electrochemical degradation of aniline followed pseudo-first-order kinetics.The aniline（200 mL of 100mg·L-（-1）） and COD removal efficiencies reached 100%and 73.5%,respectively,at a current density of 20 mA·cm-（-2）,pH of 7.0,and supporting electrolyte of 0.5 wt%Na2SO4 after 2 h electrolysis in a 3D reactor.These results show that aniline can be significantly removed on the Ti/TiOxHy/Sb-SnO2electrode,which provides an efficient way for elimination of aniline from aqueous solution.展开更多
Ti/Sb-SnO2 anodes were prepared by thermal decomposition to examine the influence of the amount of Sb dopant on the structure and electrocatalytic capability of the electrodes in the oxidation of 4-chlorophenol. The p...Ti/Sb-SnO2 anodes were prepared by thermal decomposition to examine the influence of the amount of Sb dopant on the structure and electrocatalytic capability of the electrodes in the oxidation of 4-chlorophenol. The physicochemical properties of the Sb-SnO2 coating were markedly influenced by different amounts of Sb dopant. The electrodes, which contained 5% Sb dopant in the coating, presented a much more homogenous surface and much smaller mud-cracks, compared with Ti/Sb-SnO2 electrodes containing 10% or 15% Sb dopant, which exibited larger mud cracks and pores on the surface. However, the main microstructure remained unchanged with the addition of the Sb dopant. No new crystal phase was observed by X-ray diffraction （XRD）. The electrochemical oxidation of 4-chlorophenol on the Ti/SnO2 electrode with 5% Sb dopant was inclined to electrochemical combustion; while for those containing more Sb dopant, intermediate species were accumulated. The electrodes with 5% Sb dopant showed the highest efficiency in the bulk electrolysis of 4-chlorophenol at a current density of 20 mA/cm^2 for 180 min; and the removal rates of 4-chlorophenol and COD were 51.0% and 48.9%, respectively.展开更多
Ti3C2Tx,a novel two-dimensional layer material,is widely used as electrode materials of supercapacitor due to its good metal conductivity,redox reaction active surface,and so on.However,there are many challenges to be...Ti3C2Tx,a novel two-dimensional layer material,is widely used as electrode materials of supercapacitor due to its good metal conductivity,redox reaction active surface,and so on.However,there are many challenges to be addressed which impede Ti3C2Tx obtaining the ideal specific capacitance,such as restacking,re-crushing,and oxidation of titanium.Recently,many advances have been proposed to enhance capacitance performance of Ti3C2Tx.In this review,recent strategies for improving specific capacitance are summarized and compared,for example,film formation,surface modification,and composite method.Furthermore,in order to comprehend the mechanism of those efforts,this review analyzes the energy storage performance in different electrolytes and influencing factors.This review is expected to predict redouble research direction of Ti3C2Tx materials in supercapacitors.展开更多
Praseodymium was selected as a promoter for SnO2/Ti electrode to improve the electrocatalytic performance by electrodeposition in pharmaceutical wastewater treatment; the micrograph and the structure were characterize...Praseodymium was selected as a promoter for SnO2/Ti electrode to improve the electrocatalytic performance by electrodeposition in pharmaceutical wastewater treatment; the micrograph and the structure were characterized by SEM and XRD. Mixture uniform design was used in the optimization of the electrolytic conditions; mathematical model was established according to the rate of wiping COD off, which revealed the relationship between the current intensity, time of electrolysis, the amount of doped Pr, and the ratio of area （SnOJTi：Al）. On the basis of the analysis of the empirical model, the optimized parameters had been obtained; the rate of wiping COD off was up to 94.9%, it decreased from 392 to 20 mg/L. Experimental results showed that the electrocatalytic performance of the electrode doped with Pr was superior for the treatment of pharmaceutical wastewater.展开更多
Electrochemicaldegradation of2,4-dichlorophenol （2,4-DCP） in aqueous solutionwas investigated over Ti/SnO2-Sb anode. The factors influencing thedegradation rate, such as applied currentdensity （2-40 mA/cm2 ）, pH ...Electrochemicaldegradation of2,4-dichlorophenol （2,4-DCP） in aqueous solutionwas investigated over Ti/SnO2-Sb anode. The factors influencing thedegradation rate, such as applied currentdensity （2-40 mA/cm2 ）, pH （3-11） and initial concentration （5-200 mg/L）were evaluated. Thedegradation of2,4-DCP followed apparent pseudo first-order kinetics. Thedegradation ratio on Ti/SnO2 -Sb anode attained 〉 99.9% after 20 min of electrolysis at initial 5-200 mg/L concentrations at a constant currentdensity of 30 mA/cm2 with a 10 mmol/L sodium sulphate （Na2SO4 ） supporting electrolyte solution. The results showed that 2,4-DCP （100 mg/L）degradation and total organic carbon （TOC） removal ratio achieved 99.9% and 92.8%, respectively, at the optimal conditions after 30 min electrolysis. Under this condition, thedegradation rate constant （k） and thedegradation half-life （t1/2 ）were 0.21 min1 and （2.8 ± 0.2） min, respectively. Mainly carboxylic acids （propanoic acid, maleic acid, propanedioic acid, acetic acid and oxalic acid） weredetected as intermediates. The energy efficiencies for2,4-DCPdegradation （5-200 mg/L）with Ti/SnO2-Sb anode ranged from 0.672 to 1.602 g/kWh. The Ti/SnO2-Sb anodewith a high activity to rapid organic oxidation could be employed todegrade chlorophenols, particularly2,4-DCP inwastewater.展开更多
Regulation of the electronic structure and interface property becomes a major strategy in the preparation of electrocatalyst.This paper reports the synthesis of cerium(Ce)and sodium dodecyl benzene sulfonate(SDBS)como...Regulation of the electronic structure and interface property becomes a major strategy in the preparation of electrocatalyst.This paper reports the synthesis of cerium(Ce)and sodium dodecyl benzene sulfonate(SDBS)comodified Ti/PbO_(2)electrodes(Ti/PbO2CeSDBS).Ce and SDBS could greatly change the electronic structure and interface property of PbO2.Ti/PbO_(2)CeSDBS exhibited excellent electrocatalytic activity and stability in Rhodamine B(RhB)electrocatalytic oxidation reaction.The improved electrocatalytic activity associates with the synergistic effect of electronic and interface factors.In the electrochemical degradation of RhB,the removal efficiencies of RhB and COD are about 0.880 and 0.694 respectively after the electrolysis of 220 min with Ti/PbO_(2)Ce4SDBS40,which are higher than the contrast Ti/PbO_(2)electrodes.In the meantime,the accelerated lifetime of Ti/PbO_(2)Ce4SDBS40 is more than 6.2 times than that of Ti/PbO_(2).展开更多
The electrochemical treatment of COD contained in biologically pretreated coking wastewater treated by a three-dimensional electrode system with modified coke as the particle electrode was investigated. And the electr...The electrochemical treatment of COD contained in biologically pretreated coking wastewater treated by a three-dimensional electrode system with modified coke as the particle electrode was investigated. And the electrochemical perromance of the coke modified with various active components was studied. The results show that the coke modified with Fe（NO3）2 has the lowest energy consumption and higher COD removal rate under the same condition, and the modified coke has better surface characteristics for the purpose of this study. In addition, the kinetic constant was also calculated. The study shows that the three-dimensional electrode system with Fe （NO3）z-modified coke can give a satisfactory solution in biologically pretreated coking wastewater.展开更多
Ti/SnO2–Sb electrode has a good effect on the removal of organic pollutants. But its short service life limits its large-scale application in industry. Electro-catalytic degradation performances and service life of t...Ti/SnO2–Sb electrode has a good effect on the removal of organic pollutants. But its short service life limits its large-scale application in industry. Electro-catalytic degradation performances and service life of the electrode can be significantly improved by doping rare earth（RE） ions into the oxide coating of Ti/SnO2–Sb electrode. Ti/SnO2–Sb electrodes doped with different RE elements（Ce, Dy, La, and Eu） were prepared by the thermal decomposition method at 550 ℃. Electro-catalytic degradation performances of electrodes doped with different RE elements were evaluated by linear sweep voltammetry（LSV） and Tafel curves. During the electrolysis,the conversion of p-nitrophenol was performed with these electrodes as anodes under galvanostatic control. The structures and morphologies of the surface coating of the electrodes were characterized by scanning electron microscope（SEM）. The results demonstrate that the electro-catalytic degradation performances of Ti/SnO2–Sb electrodes are improved to different levels by doping different RE ions. Improved Ti/SnO2–Sb electrodes by the introduction of different RE have higher oxygen evolution potential, better electro-catalysis ability, better coverage,and longer electrode life.展开更多
The degradation of ethinylestradiol (EE, an orally bio-active estrogen) in an aqueous-methanolic solution using a Ti/TiO2 thin-film electrode and UV radiation (a photoelectrocatalytic system) was evaluated. Hence, HPL...The degradation of ethinylestradiol (EE, an orally bio-active estrogen) in an aqueous-methanolic solution using a Ti/TiO2 thin-film electrode and UV radiation (a photoelectrocatalytic system) was evaluated. Hence, HPLC/UV analysis shows that EE (at 0.34 mmol) is totally consumed after 30 minutes of exposure to the photoelectrocatalytic system in the presence of Na2SO4 (0.1 mol·L-1) and with an applied bias potential of +1.0 V versus the Ag/AgCl reference electrode. Moreover, monitoring by direct infusion electrospray ionization mass spectrometry (ESI-MS) and SPME-GC/ MS (solid phase microextraction coupled with gas chromatography-mass spectrometry) reveals that apparently no degradation products are formed under these conditions. Hence, this study demonstrates that the photoelectrocatalytic system can be efficiently used to promote the complete degradation (and likely mineralization) of this hormone under these conditions.展开更多
基金Project(50964008)supported by the National Natural Science Foundation of ChinaProject(2010287)supported by Analysis and Testing Foundation of Kunming University of Science and Technology,China
文摘Al/α-PbO2/β-PbO2 composite electrodes doped with rare earth oxide （CeO2） were prepared by anodic oxidation method investigate the influence of nano-CeO2 dopants on the properties of Al/α-PbO2/β-PbO2-CeO2 electrodes and the impact of α-PbO2 as the intermediate layer. The results show that using α-PbO2 as the intermediate layer will benefit the crystallization of β-PbO2 and β-PbO2 is more suitable as the surface layer than α-PbO2. CeO2 dopants change the crystallite size and crystal structure, enhance the catalytic activity, and even change the deposition mechanism of PbO2. The doping of CeO2 in the PbO2 electrodes can enhance the electro-catalytic activity, which is helpful for oxygen evolution, and therefore reduce the cell voltage.
基金Projects(51004056,51004057)supported by the National Natural Science Foundation of ChinaProject(KKZ6201152009)supported by the Opening Foundation of Key Laboratory of Inorganic Coating Materials,Chinese Academy of Sciences+2 种基金Project(2010ZC052)supported by the Applied Basic Research Foundation of Yunnan Province,ChinaProject(20125314110011)supported by the Specialized Research Fund for the Doctoral Program of Higher Education,ChinaProject(2010247)supported by Analysis&Testing Foundation of Kunming University of Science and Technology,China
文摘Al/conductive coating/α-Pb O2-Ce O2-Ti O2/β-PbO 2-MnO 2-WC-Zr O2 composite electrode material was prepared on Al/conductive coating/α-PbO 2-Ce O2-Ti O2 substrate by electrochemical oxidation co-deposition technique. The effects of current density on the chemical composition, electrocatalytic activity, and stability of the composite anode material were investigated by energy dispersive X-ray spectroscopy（EDXS）, anode polarization curves, quasi-stationary polarization（Tafel） curves, electrochemical impedance spectroscopy（EIS）, scanning electron microscopy（SEM）, and X-ray diffraction（XRD）. Results reveal that the composite electrode obtained at 1 A/dm2 possesses the lowest overpotential（0.610 V at 500 A/m2） for oxygen evolution, the best electrocatalytic activity, the longest service life（360 h at 40 °C in 150 g/L H2SO4 solution under 2 A/cm2）, and the lowest cell voltage（2.75 V at 500 A/m2）. Furthermore, with increasing current density, the coating exhibits grain growth and the decrease of content of Mn O2. Only a slight effect on crystalline structure is observed.
基金supported by a GRF grant (No.CUHK477610) of the Research Grants Council of Hong Kong SAR Governmentthe National Natural Science Foundation of China (No. 50708037)
文摘β-PbO2 electrodes were prepared by electro-deposition and characterized by scanning electron microscopy,X-ray diffraction,X-ray photoelectron spectroscopy,and linear sweep voltammetry.We confirmed pure β-PbO2 crystals were on the electrode and it had a high oxygen evolution potential.The photoactivity and photoelectrochemical（PEC） properties of the β-PbO2 electrode were investigated under visible light irradiation（λ 〉 420 nm） for the decolorization of Methylene Blue.Pseudo first-order kinetics parameter（Kapp） for dye decolorization using the β-PbO2 electrode achieved 6.71×10-4 min-1 under visible light irradiation,which indicated its excellent visible light-induced photoactivity.The Kapp of the PEC process was as much as 1.41×10-3 min-1 and was 1.71 times that of visible light irradiation or electrolysis even in the presence of the β-PbO2 electrode.A significant synergetic effect was observed in the PEC system.We also employed TiO2 modified β-PbO2 electrodes in this test,which revealed that the TiO2 immobilized on the β-PbO2 electrode inhibited the visible light-induced PEC efficiency despite the amount of TiO2 used for electrode preparation.The β-PbO2 electrode was also superior to the dimensionally stable anode（Ti/Ru0.3Ti0.7O2） in visible light-induced photoactivity and PEC efficiency.
基金We are greateful to the National Narural Science Foundation of China(No.20455017)Science and Technology Committee of Shanghai Municipal(No.0452nm084).
文摘A novel nano crystalline Ag2O2-PbO2 film chemically modified electrode (CME) was prepared and the CME was characterized by X-ray diffractometer (XRD) and atomic force microscope (AFM). By chronoamperometry, the nano Ag2O2-PbO2 CME was used as bioelectro- chemical sensor to determine the population of Escherichia coli (E. coli) in water. Compared with conventional methods, it is found that the technique we used is fast and convenient in counting E. coli.
基金supported by the National Natural Science Foundation of China(21507104)the Fundamental Research Funds for the Central Universities of China
文摘Electrochemical oxidation of aniline in aqueous solution was investigated over a novel Ti/TiOxHy/Sb-SnO2 electrode prepared by the electrodeposition method.Scanning electron microscopy,X-ray diffraction,and electrochemical measurements were used to characterize its morphology,crystal structure,and electrochemical properties.Removal of aniline by the Ti/TiOxHy/Sb-SnO2electrode was investigated by ultraviolet-Visible spectroscopy and chemical oxygen demand（COD）analysis under different conditions,including current densities,initial concentrations of aniline,pH values,concentrations of chloride ions,and types of reactor.It was found that a higher current density,a lower initial concentration of aniline,an acidic solution,the presence of chloride ions（0.2wt%NaCl）,and a three-dimensional（3D） reactor promoted the removal efficiency of aniline.Electrochemical degradation of aniline followed pseudo-first-order kinetics.The aniline（200 mL of 100mg·L-（-1）） and COD removal efficiencies reached 100%and 73.5%,respectively,at a current density of 20 mA·cm-（-2）,pH of 7.0,and supporting electrolyte of 0.5 wt%Na2SO4 after 2 h electrolysis in a 3D reactor.These results show that aniline can be significantly removed on the Ti/TiOxHy/Sb-SnO2electrode,which provides an efficient way for elimination of aniline from aqueous solution.
基金Project supported by the Institute of Environmental Engineering,Peking University and China Postdoctoral Science Foundation(No.2005037032)
文摘Ti/Sb-SnO2 anodes were prepared by thermal decomposition to examine the influence of the amount of Sb dopant on the structure and electrocatalytic capability of the electrodes in the oxidation of 4-chlorophenol. The physicochemical properties of the Sb-SnO2 coating were markedly influenced by different amounts of Sb dopant. The electrodes, which contained 5% Sb dopant in the coating, presented a much more homogenous surface and much smaller mud-cracks, compared with Ti/Sb-SnO2 electrodes containing 10% or 15% Sb dopant, which exibited larger mud cracks and pores on the surface. However, the main microstructure remained unchanged with the addition of the Sb dopant. No new crystal phase was observed by X-ray diffraction （XRD）. The electrochemical oxidation of 4-chlorophenol on the Ti/SnO2 electrode with 5% Sb dopant was inclined to electrochemical combustion; while for those containing more Sb dopant, intermediate species were accumulated. The electrodes with 5% Sb dopant showed the highest efficiency in the bulk electrolysis of 4-chlorophenol at a current density of 20 mA/cm^2 for 180 min; and the removal rates of 4-chlorophenol and COD were 51.0% and 48.9%, respectively.
基金National Natural Science Foundation of China with Grant No.21905304Natural Science Foundation of Shandong Province(No.ZR2019BEM031)the Fundamental Research Funds for the Central Universities(Nos.18CX02158A and 19CX05001A).
文摘Ti3C2Tx,a novel two-dimensional layer material,is widely used as electrode materials of supercapacitor due to its good metal conductivity,redox reaction active surface,and so on.However,there are many challenges to be addressed which impede Ti3C2Tx obtaining the ideal specific capacitance,such as restacking,re-crushing,and oxidation of titanium.Recently,many advances have been proposed to enhance capacitance performance of Ti3C2Tx.In this review,recent strategies for improving specific capacitance are summarized and compared,for example,film formation,surface modification,and composite method.Furthermore,in order to comprehend the mechanism of those efforts,this review analyzes the energy storage performance in different electrolytes and influencing factors.This review is expected to predict redouble research direction of Ti3C2Tx materials in supercapacitors.
基金the Fund of the Natural Science of Guangxi (0731015)
文摘Praseodymium was selected as a promoter for SnO2/Ti electrode to improve the electrocatalytic performance by electrodeposition in pharmaceutical wastewater treatment; the micrograph and the structure were characterized by SEM and XRD. Mixture uniform design was used in the optimization of the electrolytic conditions; mathematical model was established according to the rate of wiping COD off, which revealed the relationship between the current intensity, time of electrolysis, the amount of doped Pr, and the ratio of area （SnOJTi：Al）. On the basis of the analysis of the empirical model, the optimized parameters had been obtained; the rate of wiping COD off was up to 94.9%, it decreased from 392 to 20 mg/L. Experimental results showed that the electrocatalytic performance of the electrode doped with Pr was superior for the treatment of pharmaceutical wastewater.
基金supported by the National Science Foundation for Innovative Research Group of China(No.51121003)the Specialized Research Fund for the Doctoral Program of Higher Education of China(No.20110003110023)the special fund of State Key Joint Laboratory of Environment Simulation and Pollution Control of China
文摘Electrochemicaldegradation of2,4-dichlorophenol （2,4-DCP） in aqueous solutionwas investigated over Ti/SnO2-Sb anode. The factors influencing thedegradation rate, such as applied currentdensity （2-40 mA/cm2 ）, pH （3-11） and initial concentration （5-200 mg/L）were evaluated. Thedegradation of2,4-DCP followed apparent pseudo first-order kinetics. Thedegradation ratio on Ti/SnO2 -Sb anode attained 〉 99.9% after 20 min of electrolysis at initial 5-200 mg/L concentrations at a constant currentdensity of 30 mA/cm2 with a 10 mmol/L sodium sulphate （Na2SO4 ） supporting electrolyte solution. The results showed that 2,4-DCP （100 mg/L）degradation and total organic carbon （TOC） removal ratio achieved 99.9% and 92.8%, respectively, at the optimal conditions after 30 min electrolysis. Under this condition, thedegradation rate constant （k） and thedegradation half-life （t1/2 ）were 0.21 min1 and （2.8 ± 0.2） min, respectively. Mainly carboxylic acids （propanoic acid, maleic acid, propanedioic acid, acetic acid and oxalic acid） weredetected as intermediates. The energy efficiencies for2,4-DCPdegradation （5-200 mg/L）with Ti/SnO2-Sb anode ranged from 0.672 to 1.602 g/kWh. The Ti/SnO2-Sb anodewith a high activity to rapid organic oxidation could be employed todegrade chlorophenols, particularly2,4-DCP inwastewater.
基金Thanks to the financial support from the Science and technology project of Shaanxi Province(2017ZDXM-GY-041).
文摘Regulation of the electronic structure and interface property becomes a major strategy in the preparation of electrocatalyst.This paper reports the synthesis of cerium(Ce)and sodium dodecyl benzene sulfonate(SDBS)comodified Ti/PbO_(2)electrodes(Ti/PbO2CeSDBS).Ce and SDBS could greatly change the electronic structure and interface property of PbO2.Ti/PbO_(2)CeSDBS exhibited excellent electrocatalytic activity and stability in Rhodamine B(RhB)electrocatalytic oxidation reaction.The improved electrocatalytic activity associates with the synergistic effect of electronic and interface factors.In the electrochemical degradation of RhB,the removal efficiencies of RhB and COD are about 0.880 and 0.694 respectively after the electrolysis of 220 min with Ti/PbO_(2)Ce4SDBS40,which are higher than the contrast Ti/PbO_(2)electrodes.In the meantime,the accelerated lifetime of Ti/PbO_(2)Ce4SDBS40 is more than 6.2 times than that of Ti/PbO_(2).
文摘The electrochemical treatment of COD contained in biologically pretreated coking wastewater treated by a three-dimensional electrode system with modified coke as the particle electrode was investigated. And the electrochemical perromance of the coke modified with various active components was studied. The results show that the coke modified with Fe（NO3）2 has the lowest energy consumption and higher COD removal rate under the same condition, and the modified coke has better surface characteristics for the purpose of this study. In addition, the kinetic constant was also calculated. The study shows that the three-dimensional electrode system with Fe （NO3）z-modified coke can give a satisfactory solution in biologically pretreated coking wastewater.
基金financially supported by the National Natural Science Foundation of China (No. 51364024 and 51404124)Gansu Province Department of Education Fund (No. 2013A-029)the Foundation of State Key Laboratory of Gansu Advanced Nonferrous Metal Materials (Nos. SKL 1316 and SKL 1314)
文摘Ti/SnO2–Sb electrode has a good effect on the removal of organic pollutants. But its short service life limits its large-scale application in industry. Electro-catalytic degradation performances and service life of the electrode can be significantly improved by doping rare earth（RE） ions into the oxide coating of Ti/SnO2–Sb electrode. Ti/SnO2–Sb electrodes doped with different RE elements（Ce, Dy, La, and Eu） were prepared by the thermal decomposition method at 550 ℃. Electro-catalytic degradation performances of electrodes doped with different RE elements were evaluated by linear sweep voltammetry（LSV） and Tafel curves. During the electrolysis,the conversion of p-nitrophenol was performed with these electrodes as anodes under galvanostatic control. The structures and morphologies of the surface coating of the electrodes were characterized by scanning electron microscope（SEM）. The results demonstrate that the electro-catalytic degradation performances of Ti/SnO2–Sb electrodes are improved to different levels by doping different RE ions. Improved Ti/SnO2–Sb electrodes by the introduction of different RE have higher oxygen evolution potential, better electro-catalysis ability, better coverage,and longer electrode life.
文摘The degradation of ethinylestradiol (EE, an orally bio-active estrogen) in an aqueous-methanolic solution using a Ti/TiO2 thin-film electrode and UV radiation (a photoelectrocatalytic system) was evaluated. Hence, HPLC/UV analysis shows that EE (at 0.34 mmol) is totally consumed after 30 minutes of exposure to the photoelectrocatalytic system in the presence of Na2SO4 (0.1 mol·L-1) and with an applied bias potential of +1.0 V versus the Ag/AgCl reference electrode. Moreover, monitoring by direct infusion electrospray ionization mass spectrometry (ESI-MS) and SPME-GC/ MS (solid phase microextraction coupled with gas chromatography-mass spectrometry) reveals that apparently no degradation products are formed under these conditions. Hence, this study demonstrates that the photoelectrocatalytic system can be efficiently used to promote the complete degradation (and likely mineralization) of this hormone under these conditions.
