A series of Al-Ti-B master alloys were prepared by different preparation routes,and the TiB2 particles in the master alloys were extracted and analyzed.It is found that the forming process has significant influence on...A series of Al-Ti-B master alloys were prepared by different preparation routes,and the TiB2 particles in the master alloys were extracted and analyzed.It is found that the forming process has significant influence on the three-dimensional morphology of TiB2 particles.Different preparation routes result in different reaction forms,which accounts for the morphology variation of TiB2 particles.When the Al-Ti-B master alloy is prepared using ＂halide salt＂ route,TiB2 particles exhibit hexagonal platelet morphology and are independent with each other.In addition,the reaction temperature almost does not have influence on the morphology of TiB2 particles.However,TiB2 particles exhibit different morphologies at different reaction temperatures when the master alloys are prepared with Al-3B and Ti sponge.When the master alloy is prepared at 850 ℃,a kind of TiB2 particle agglomeration forms with a size larger than 5 μm.The TiB2 particles change to layered stacking morphology even dendritic morphology with the reaction temperature reaching up to 1200 ℃.展开更多
Three-dimensional morphology of ferrite allotriomorphs nucleated at grain boundary edges in low carbon steel was revealed by means of serial sectioning in conjunction with computer-aided three-dimensional reconstructi...Three-dimensional morphology of ferrite allotriomorphs nucleated at grain boundary edges in low carbon steel was revealed by means of serial sectioning in conjunction with computer-aided three-dimensional reconstruction techniques. The typical morphology of them was of an elongated triangular pyramid. The length, width and thickness of ferrite allotriomorphs were measured on the basis of three-dimensional reconstructed images. The aspect ratio （length/width） of them was 4.5 on an average and scattered from 3 to 6. The measured sizes were smaller than calculated ones, which was probably attributed to solute drag-like effect of manganese in the alloy.展开更多
The formation of intragranular ferrite at inclusions was analyzed by SEM-EDX in a vanadium microalloyed steel with an excess amount of sulfur. The precipitation of MnS at aluminum oxides may result in Mn depletion, wh...The formation of intragranular ferrite at inclusions was analyzed by SEM-EDX in a vanadium microalloyed steel with an excess amount of sulfur. The precipitation of MnS at aluminum oxides may result in Mn depletion, which, in turn, promotes the formation of intragranular ferrite. The morphology of intragranular ferrite changed with undercooling. At higher temperatures intragranular ferrite is nearly equiaxed whereas it is plate-like at lower temperatures.展开更多
The shear failure of intact rock under thermo-mechanical(TM)coupling conditions is common,such as in enhanced geothermal mining and deep mine construction.Under the effect of a continuous engineering disturbance,shear...The shear failure of intact rock under thermo-mechanical(TM)coupling conditions is common,such as in enhanced geothermal mining and deep mine construction.Under the effect of a continuous engineering disturbance,shear-formed fractures are prone to secondary instability,posing a severe threat to deep engineering.Although numerous studies regarding three-dimensional(3D)morphologies of fracture surfaces have been conducted,the understanding of shear-formed fractures under TM coupling conditions is limited.In this study,direct shear tests of intact granite under various TM coupling conditions were conducted,followed by 3D laser scanning tests of shear-formed fractures.Test results demonstrated that the peak shear strength of intact granite is positively correlated with the normal stress,whereas it is negatively correlated with the temperature.The internal friction angle and cohesion of intact granite significantly decrease with an increase in the temperature.The anisotropy,roughness value,and height of the asperities on the fracture surfaces are reduced as the normal stress increases,whereas their variation trends are the opposite as the temperature increases.The macroscopic failure mode of intact granite under TM coupling conditions is dominated by mixed tensileeshear and shear failures.As the normal stress increases,intragranular fractures are developed ranging from a local to a global distribution,and the macroscopic failure mode of intact granite changes from mixed tensileeshear to shear failure.Finally,3D morphological characteristics of the asperities on the shear-formed fracture surfaces were analyzed,and a quadrangular pyramid conceptual model representing these asperities was proposed and sufficiently verified.展开更多
Morphological analyses are key outcome assessments for nerve regeneration studies but are historically limited to tissue sections.Novel optical tissue clearing techniques enabling three-dimensional imaging of entire o...Morphological analyses are key outcome assessments for nerve regeneration studies but are historically limited to tissue sections.Novel optical tissue clearing techniques enabling three-dimensional imaging of entire organs at a subcellular resolution have revolutionized morphological studies of the brain.To extend their applicability to experimental nerve repair studies we adapted these techniques to nerves and their motor and sensory targets in rats.The solvent-based protocols rendered harvested peripheral nerves and their target organs transparent within 24 hours while preserving tissue architecture and fluorescence.The optical clearing was compatible with conventional laboratory techniques,including retrograde labeling studies,and computational image segmentation,providing fast and precise cell quantitation.Further,optically cleared organs enabled three-dimensional morphometry at an unprecedented scale including dermatome-wide innervation studies,tracing of intramuscular nerve branches or mapping of neurovascular networks.Given their wide-ranging applicability,rapid processing times,and low costs,tissue clearing techniques are likely to be a key technology for next-generation nerve repair studies.All procedures were approved by the Hospital for Sick Children’s Laboratory Animal Services Committee(49871/9)on November 9,2019.展开更多
This study aims to develop a high-precision and cost-efficient method for the threedimensional reconstruction of large particles in natural gravel and blasted rock fragments,utilizing Structure from Motion(SfM)and Mul...This study aims to develop a high-precision and cost-efficient method for the threedimensional reconstruction of large particles in natural gravel and blasted rock fragments,utilizing Structure from Motion(SfM)and Multi-View Stereo(MVS)techniques.The proposed approach was applied to characterize the three-dimensional morphology of rockfill dam materials at a real construction site.Particle shape was quantitatively analyzed using shape indices of sphericity,convexity,and angularity.The predominant morphology of natural gravel is characterized as slightly elongated and slightly flat,while rock fragments are slightly elongated and not flat.Probability density distributions of shape indices follow a skewed normal distribution:sphericity and convexity show leftward skewness,whereas angularity is right-skewed.Skewness parameters of sphericity and angularity are consistent between natural gravel and blasted rock fragments,indicating comparable shape asymmetry.Convexity skewness is significantly higher in natural gravel compared to rock fragments,by approximately an order of magnitude.The relationship between size and particle shape shows that form ratios and associated shape descriptors change linearly with the logarithm of size;larger particles approach spherical or cubic forms.The innovative measurements contribute to the particle shape data set of rockfill dam materials,providing valuable insights into the three-dimensional and statistical morphological characteristics of relatively large particles in natural gravel and blasted rock fragments.This approach enhances understanding of particle morphology's impact on the mechanical behavior of granular materials.展开更多
AIM To assess the role of three-dimensional endoanal ultrasound (3D-EAUS) for morphological assessment of the anal sphincter of female patients with chronic proctalgia (CP). METHODS In this unmatched case control stud...AIM To assess the role of three-dimensional endoanal ultrasound (3D-EAUS) for morphological assessment of the anal sphincter of female patients with chronic proctalgia (CP). METHODS In this unmatched case control study, 30 consecutive female patients with CP and 25 normal women (control group) were enrolled. 3D-EAUS was performed in all subjects. Thickness and length of internal anal sphincter (IAS), thickness of puborectalis muscle (PR), length of the external anal sphincter (EAS) plus PR, and puborectalis angle were measured and compared between the two groups. RESULTS Patients with CP had significantly shorter IAS length and greater PR thickness, as compared to those in normal individuals (26.28 +/- 3.59 mm vs 28.87 +/- 4.84 mm, P < 0.05 and 9.67 +/- 1.57 mm vs 8.85 +/- 0.97 mm, P < 0.05, respectively). No significant between-group differences were observed with respect to IAS thickness and the EAS plus PR length (P > 0.05). Puborectalis angle in the CP group was significantly decreased, both in resting (88.23 degrees +/- 1.81 degrees vs 89.94 degrees +/- 2.07 degrees in control group, P < 0.05) and straining (88.47 degrees +/- 3.32 degrees vs 90.72 degrees +/- 1.87 degrees in control group, P < 0.05) phases, which suggest the presence of paradoxical contraction of PR in patients with CP. In the CP group, no significant difference in puborectalis angle was observed between the resting and straining phases (88.23 degrees +/- 1.81 degrees vs 88.47 degrees +/- 3.32 degrees respectively, P > 0.05). CONCLUSION The association of greater PR thickness and paradoxical contraction of PR with CP suggest their potential value as markers of CP.展开更多
A web camera based multi-camera convergent close-range photogrammetric system is developed to obtain the neonates＇ head and facial morphology. The data will then be used to develop a secure and good-fitting eye-patch...A web camera based multi-camera convergent close-range photogrammetric system is developed to obtain the neonates＇ head and facial morphology. The data will then be used to develop a secure and good-fitting eye-patch protector for neonates, particularly whoa they are exposed to bright lights such as phototherapy light. Measurements obtained by the system are evaluated and validated against data obtained from optical scanning. Results show that the photogrammetric system meets the requirements of measuring accuracy and safety for neonate in the neonatal units.展开更多
To evaluate the morphology of atrial septum by the live three-dimensional echocardiography （L3DE） and its value of clinical application, L3DE was performed in 62 subjects to observe the morphological characteristics...To evaluate the morphology of atrial septum by the live three-dimensional echocardiography （L3DE） and its value of clinical application, L3DE was performed in 62 subjects to observe the morphological characteristics and dynamic change of the overall anatomic structure of atrial septum. The study examined 49 patients with atrial septal defect （ASD）, including 3 patients with atrial septal aneurysm, and 10 healthy subjects. ASD in the 35 patients was surgically confirmed. The maximal diameters of ASD were measured and the percentages of area change were calculated. The parameters derived from L3DE were compared with intraoperative measurements. The results showed that L3DE could directly and clearly display the morphological features of overall anatomic structure of normal atrial septum, repaired and artificially-occluded atrial septum, atrial septal aneurysm. The defect area in ASD patients changed significantly during cardiac cycle, which reached a maximum at end-systole and a minimum at end-diastole, with a mean change percentage of 46.6%, ranging from 14.8% to 73.4%. The sizes obtained from L3DE bore an excellent correlation with intraoperative findings （r=0.90）. It is concluded that L3DE can clearly display the overall morphological features and dynamic change of atrial septum and measure the size of ASD area accurately, which is important in the decision to choose therapeutic protocols.展开更多
A method for observing the three-dimensional morphologies of inclusions by deeply eroding a steel sample with a kind of organic solution composed of bromine water, acetone, and HCl （volume ratio, 45：45：10） was int...A method for observing the three-dimensional morphologies of inclusions by deeply eroding a steel sample with a kind of organic solution composed of bromine water, acetone, and HCl （volume ratio, 45：45：10） was introduced. Four different kinds of inclusions in ultra low carbon steel were compared by metallographic observation and erosion observation. The results show that the three-dimensional morphologies of different kinds of inclusions could be observed clearly and simply after erosion. The method is useful for the observation and analysis of inclusions made by deep erosion. It also provides a new way to control and remove inclusions based on the true morphologies of inclusions.展开更多
This study aimed to examine the differences in the morphological properties and proliferation of olfactory ensheathing cells in three-dimensional culture on collagen-heparan sulfate biological scaffolds and in two-dim...This study aimed to examine the differences in the morphological properties and proliferation of olfactory ensheathing cells in three-dimensional culture on collagen-heparan sulfate biological scaffolds and in two-dimensional culture on common flat culture plates. The proliferation rate of olfactory ensheathing cells in three-dimensional culture was higher than that in two-dimensional culture, as detected by an M-I-r assay. In addition, more than half of the olfactory ensheathing cells subcultured using the trypsinization method in three-dimensional culture displayed a spindly Schwann cell-like morphology with extremely long processes, while they showed a flat astrocyte-like morphology in two-dimensional culture. Moreover, spindle-shaped olfactory ensheathing cells tended to adopt an elongated bipolar morphology under both culture conditions. Experimental findings indicate that the morphological properties and proliferation of olfactory ensheathing cells in three-dimensional culture on collagen-heparan sulfate biological scaffolds are better than those in two-dimensional culture.展开更多
Fish morphological phenotypes are important resources in artificial breeding,functional gene mapping,and population-based studies in aquaculture and ecology.Traditional morphological measurement of phenotypes is rathe...Fish morphological phenotypes are important resources in artificial breeding,functional gene mapping,and population-based studies in aquaculture and ecology.Traditional morphological measurement of phenotypes is rather expensive in terms of time and labor.More importantly,manual measurement is highly dependent on operational experience,which can lead to subjective phenotyping results.Here,we developed 3DPhenoFish software to extract fish morphological phenotypes from three-dimensional(3D)point cloud data.Algorithms for background elimination,coordinate normalization,image segmentation,key point recognition,and phenotype extraction were developed and integrated into an intuitive user interface.Furthermore,18 key points and traditional 2D morphological traits,along with 3D phenotypes,including area and volume,can be automatically obtained in a visualized manner.Intuitive fine-tuning of key points and customized definitions of phenotypes are also allowed in the software.Using 3DPhenoFish,we performed high-throughput phenotyping for four endemic Schizothoracinae species,including Schizopygopsis younghusbandi,Oxygymnocypris stewartii,Ptychobarbus dipogon,and Schizothorax oconnori.Results indicated that the morphological phenotypes from 3DPhenoFish exhibited high linear correlation(>0.94)with manual measurements and offered informative traits to discriminate samples of different species and even for different populations of the same species.In summary,we developed an efficient,accurate,and customizable tool,3DPhenoFish,to extract morphological phenotypes from point cloud data,which should help overcome traditional challenges in manual measurements.3DPhenoFish can be used for research on morphological phenotypes in fish,including functional gene mapping,artificial selection,and conservation studies.3DPhenoFish is an open-source software and can be downloaded for free at https://github.com/lyh24k/3DPhenoFish/tree/master.展开更多
Three-dimensional(3D)urban structures play a critical role in informing climate mitigation strategies aimed at the built environment and facilitating sustainable urban development.Regrettably,there exists a significan...Three-dimensional(3D)urban structures play a critical role in informing climate mitigation strategies aimed at the built environment and facilitating sustainable urban development.Regrettably,there exists a significant gap in detailed and consistent data on 3D building space structures with global coverage due to the challenges inherent in the data collection and model calibration processes.In this study,we constructed a global urban structure(GUS-3D)dataset,including building volume,height,and footprint information,at a 500 m spatial resolution using extensive satellite observation products and numerous reference building samples.Our analysis indicated that the total volume of buildings worldwide in2015 exceeded 1×10^(12)m^(3).Over the 1985 to 2015 period,we observed a slight increase in the magnitude of 3D building volume growth(i.e.,it increased from 166.02 km3 during the 1985–2000 period to 175.08km3 during the 2000–2015 period),while the expansion magnitudes of the two-dimensional(2D)building footprint(22.51×10^(3) vs 13.29×10^(3)km^(2))and urban extent(157×10^(3) vs 133.8×10^(3)km^(2))notably decreased.This trend highlights the significant increase in intensive vertical utilization of urban land.Furthermore,we identified significant heterogeneity in building space provision and inequality across cities worldwide.This inequality is particularly pronounced in many populous Asian cities,which has been overlooked in previous studies on economic inequality.The GUS-3D dataset shows great potential to deepen our understanding of the urban environment and creates new horizons for numerous 3D urban studies.展开更多
To address the problem of multi-missile cooperative interception against maneuvering targets at a prespecified impact time and desired Line-of-Sight(LOS)angles in ThreeDimensional(3D)space,this paper proposes a 3D lea...To address the problem of multi-missile cooperative interception against maneuvering targets at a prespecified impact time and desired Line-of-Sight(LOS)angles in ThreeDimensional(3D)space,this paper proposes a 3D leader-following cooperative interception guidance law.First,in the LOS direction of the leader,an impact time-controlled guidance law is derived based on the fixed-time stability theory,which enables the leader to complete the interception task at a prespecified impact time.Next,in the LOS direction of the followers,by introducing a time consensus tracking error function,a fixed-time consensus tracking guidance law is investigated to guarantee the consensus tracking convergence of the time-to-go.Then,in the direction normal to the LOS,by combining the designed global integral sliding mode surface and the second-order Sliding Mode Control(SMC)theory,an innovative 3D LOS-angle-constrained interception guidance law is developed,which eliminates the reaching phase in the traditional sliding mode guidance laws and effectively saves energy consumption.Moreover,it effectively suppresses the chattering phenomenon while avoiding the singularity issue,and compensates for unknown interference caused by target maneuvering online,making it convenient for practical engineering applications.Finally,theoretical proof analysis and multiple sets of numerical simulation results verify the effectiveness,superiority,and robustness of the investigated guidance law.展开更多
Zinc oxide(ZnO)serves as a crucial functional semiconductor with a wide direct bandgap of approximately 3.37 eV.Solvothermal reaction is commonly used in the synthesis of ZnO micro/nanostructures,given its low cost,si...Zinc oxide(ZnO)serves as a crucial functional semiconductor with a wide direct bandgap of approximately 3.37 eV.Solvothermal reaction is commonly used in the synthesis of ZnO micro/nanostructures,given its low cost,simplicity,and easy implementation.Moreover,ZnO morphology engineering has become desirable through the alteration of minor conditions in the reaction process,particularly at room temperature.In this work,ZnO micro/nanostructures were synthesized in a solution by varying the amounts of the ammonia added at low temperatures(including room temperature).The formation of Zn^(2+)complexes by ammonia in the precursor regulated the reaction rate of the morphology engineering of ZnO,which resulted in various structures,such as nanoparticles,nanosheets,microflowers,and single crystals.Finally,the obtained ZnO was used in the optoelectronic application of ultraviolet detectors.展开更多
Multicomponent Gd_(1−x)Sm_(x)Ba_(0.5)Sr_(0.5)CoCuO_(5+δ)double perovskites are optimized for application in terms of chemical composi-tion and morphology for the use as oxygen electrodes in solid oxide cells.Structur...Multicomponent Gd_(1−x)Sm_(x)Ba_(0.5)Sr_(0.5)CoCuO_(5+δ)double perovskites are optimized for application in terms of chemical composi-tion and morphology for the use as oxygen electrodes in solid oxide cells.Structural studies of other physicochemical properties are con-ducted on a series of materials obtained by the sol-gel method with different ratios of Gd and Sm cations.It is documented that changing the x value,and the resulting adjustment of the average ionic radius,have a significant impact on the crystal structure,stability,as well as on the total conductivity and thermomechanical properties of the materials,with the best results obtained for the Gd_(0.75)Sm_(0.2)5Ba_(0.5)Sr_(0.5)CoCuO_(5+δ)composition.Oxygen electrodes are prepared using the selected compound,allowing to obtain low polarization resistance values,such as 0.086Ω·cm^(2)at 800℃.Systematic studies of electrocatalytic activity are conducted using La_(0.8)Sr_(0.2)Ga_(0.8)Mg_(_(0.2))O_(3−δ)as the electrolyte for all electrodes,and Ce_(0.8)Gd_(0.2)O_(2−δ)electrolyte for the best performing Gd_(0.75)Sm_(0.2)5Ba_(0.5)Sr_(0.5)CoCuO_(5+δ)electrodes.The electrochemical data are analyzed using the distribution of relaxation times method.Also,the influence of the preparation method of the electrode material is in-ve`stigated using the electrospinning technique.Finally,the performance of the Gd_(0.75)Sm_(0.2)5Ba_(0.5)Sr_(0.5)CoCuO_(5+δ)electrodes is tested in a Ni-YSZ(yttria-stabilized zirconia)anode-supported cell with a Ce_(0.8)Gd_(0.2)O_(2−δ)buffer layer,in the fuel cell and electrolyzer operating modes.With the electrospun electrode,a power density of 462 mW·cm^(−2)is obtained at 700℃,with a current density of ca.0.2 A·cm^(−2)at 1.3 V for the electrolysis at the same temperature,indicating better performance compared to the sol-gel-based electrode.展开更多
Laser-directed energy deposition(L-DED)is an advanced additive manufacturing technology primarily adopted in metal three-dimensional printing systems.The L-DED process is characterized by various defects,thus necessit...Laser-directed energy deposition(L-DED)is an advanced additive manufacturing technology primarily adopted in metal three-dimensional printing systems.The L-DED process is characterized by various defects,thus necessitating the extensive use of in-situ monitoring to enable real-time adjustments of process parameters by detecting molten-pool features.To address the challenge of accurately extracting the molten-pool morphology from an undetached spatter,an innovative monitoring method based on the U-Net(U-shaped network)is proposed herein.A lightweight architecture accelerates the processing speed,whereas an enhanced loss function incorporating weight maps augments the segmentation precision.The model performance is evaluated by comparing its segmentation accuracy and processing speed with those of the conventional U-Net,using the mean intersection over union(MIoU)as the segmentation metric.The improved model demonstrates superior segmentation accuracy at the interface between the molten pool and spatter,with a peak MIoU of 0.9798 achieved on the test set.Furthermore,this model processes each image in an extremely short time of 17.9 ms.Using this segmentation algorithm,the error in extracting the molten-pool width from single-track experiments is within 0.1 mm.The proposed method for monitoring the molten-pool morphology is suitable for deployment in online monitoring systems,thus providing a foundation for subsequent process-parameter regulation.展开更多
Morphological alterations in dendritic spines have been linked to changes in functional communication between neurons that affect learning and memory.Kinesin-4 KIF21A helps organize the microtubule-actin network at th...Morphological alterations in dendritic spines have been linked to changes in functional communication between neurons that affect learning and memory.Kinesin-4 KIF21A helps organize the microtubule-actin network at the cell cortex by interacting with KANK1;however,whether KIF21A modulates dendritic structure and function in neurons remains unknown.In this study,we found that KIF21A was distributed in a subset of dendritic spines,and that these KIF21A-positive spines were larger and more structurally plastic than KIF21A-negative spines.Furthermore,the interaction between KIF21A and KANK1 was found to be critical for dendritic spine morphogenesis and synaptic plasticity.Knockdown of either KIF21A or KANK1 inhibited dendritic spine morphogenesis and dendritic branching,and these deficits were fully rescued by coexpressing full-length KIF21A or KANK1,but not by proteins with mutations disrupting direct binding between KIF21A and KANK1 or binding between KANK1 and talin1.Knocking down KIF21A in the hippocampus of rats inhibited the amplitudes of long-term potentiation induced by high-frequency stimulation and negatively impacted the animals’cognitive abilities.Taken together,our findings demonstrate the function of KIF21A in modulating spine morphology and provide insight into its role in synaptic function.展开更多
Liposarcoma is one of the most common soft tissue sarcomas,however,its occurrence rate is still rare compared to other cancers.Due to its rarity,in vitro experiments are an essential approach to elucidate liposarcoma ...Liposarcoma is one of the most common soft tissue sarcomas,however,its occurrence rate is still rare compared to other cancers.Due to its rarity,in vitro experiments are an essential approach to elucidate liposarcoma pathobiology.Conventional cell culture-based research(2D cell culture)is still playing a pivotal role,while several shortcomings have been recently under discussion.In vivo,mouse models are usually adopted for pre-clinical analyses with expectations to overcome the issues of 2D cell culture.However,they do not fully recapitulate human dedifferentiated liposarcoma(DDLPS)characteristics.Therefore,three-dimensional(3D)culture systems have been the recent research focus in the cell biology field with the expectation to overcome at the same time the disadvantages of 2D cell culture and in vivo animal models and fill in the gap between them.Given the liposarcoma rarity,we believe that 3D cell culture techniques,including 3D cell cultures/co-cultures,and Patient-Derived tumor Organoids(PDOs),represent a promising approach to facilitate liposarcoma investigation and elucidate its molecular mechanisms and effective therapy development.In this review,we first provide a general overview of 3D cell cultures compared to 2D cell cultures.We then focus on one of the recent 3D cell culture applications,Patient-Derived Organoids(PDOs),summarizing and discussing several PDO methodologies.Finally,we discuss the current and future applications of PDOs to sarcoma,particularly in the field of liposarcoma.展开更多
The sedimentary bed morphology modulated by the wake flow of a wall-mounted flexible aquatic vegetation blade across various structural aspect ratios(A_(R)=l/b,where l and b are the length and width of the blade,respe...The sedimentary bed morphology modulated by the wake flow of a wall-mounted flexible aquatic vegetation blade across various structural aspect ratios(A_(R)=l/b,where l and b are the length and width of the blade,respectively)and incoming flow velocities was experimentally investigated in a water channel.A surface scanner was implemented to quantify bed topography,and a tomographic particle image velocimetry system was used to characterize the three-dimensional wake flows.The results showed that due to the deflection of incoming flow,the velocity magnitude increased at the lateral sides of the blade,thereby producing distinctive symmetric scour holes in these regions.The normalized morphology profiles of the sedimentary bed,which were extracted along the streamwise direction at the location of the maximum erosion depth,exhibited a self-similar pattern that closely followed a sinusoidal wave profile.The level of velocity magnitude enhancement was highly correlated to the postures of the flexible blade.At a given flow velocity,the blade with lower aspect ratios exhibited less significant deformation,causing more significant near-bed velocity enhancement in the wake deflection zone and therefore leading to higher erosion volumes.Further investigation indicated that when the blade underwent slight deformation,the larger velocity enhancement close to the bed can be attributed to more significant flow deflection effects at the lateral sides of the blade and stronger flow mixing with high momentum flows away from the bed.Supported with measurements,a basic formula was established to quantify the shear stress acting on the sedimentary bed as a function of incoming flow velocity and blade aspect ratio.展开更多
基金Project(50625101) supported by the National Science Fund for Distinguished Young Scholars of ChinaProject supported by Graduate Independent Innovation Foundation of Shandong University(GIIFSDU),ChinaProject(51071097) supported by the National Natural Science Foundation of China
文摘A series of Al-Ti-B master alloys were prepared by different preparation routes,and the TiB2 particles in the master alloys were extracted and analyzed.It is found that the forming process has significant influence on the three-dimensional morphology of TiB2 particles.Different preparation routes result in different reaction forms,which accounts for the morphology variation of TiB2 particles.When the Al-Ti-B master alloy is prepared using ＂halide salt＂ route,TiB2 particles exhibit hexagonal platelet morphology and are independent with each other.In addition,the reaction temperature almost does not have influence on the morphology of TiB2 particles.However,TiB2 particles exhibit different morphologies at different reaction temperatures when the master alloys are prepared with Al-3B and Ti sponge.When the master alloy is prepared at 850 ℃,a kind of TiB2 particle agglomeration forms with a size larger than 5 μm.The TiB2 particles change to layered stacking morphology even dendritic morphology with the reaction temperature reaching up to 1200 ℃.
基金Item Sponsored by National Natural Science Foundation of China and Baosteel (50734004)
文摘Three-dimensional morphology of ferrite allotriomorphs nucleated at grain boundary edges in low carbon steel was revealed by means of serial sectioning in conjunction with computer-aided three-dimensional reconstruction techniques. The typical morphology of them was of an elongated triangular pyramid. The length, width and thickness of ferrite allotriomorphs were measured on the basis of three-dimensional reconstructed images. The aspect ratio （length/width） of them was 4.5 on an average and scattered from 3 to 6. The measured sizes were smaller than calculated ones, which was probably attributed to solute drag-like effect of manganese in the alloy.
基金This project was sponsored by the Scientific Research Foundation for the Returned Overseas Chinese Scholars, the Education Ministry of China and by the Scientific Research Fund of the Education Bureau of Hubei Province, China (No.2004Q001).
文摘The formation of intragranular ferrite at inclusions was analyzed by SEM-EDX in a vanadium microalloyed steel with an excess amount of sulfur. The precipitation of MnS at aluminum oxides may result in Mn depletion, which, in turn, promotes the formation of intragranular ferrite. The morphology of intragranular ferrite changed with undercooling. At higher temperatures intragranular ferrite is nearly equiaxed whereas it is plate-like at lower temperatures.
基金supported by the National Natural Science Foundation of China(Grant No.51974173)the Natural Science Foundation of Shandong Province,China(Grant No.ZR2020QD122).
文摘The shear failure of intact rock under thermo-mechanical(TM)coupling conditions is common,such as in enhanced geothermal mining and deep mine construction.Under the effect of a continuous engineering disturbance,shear-formed fractures are prone to secondary instability,posing a severe threat to deep engineering.Although numerous studies regarding three-dimensional(3D)morphologies of fracture surfaces have been conducted,the understanding of shear-formed fractures under TM coupling conditions is limited.In this study,direct shear tests of intact granite under various TM coupling conditions were conducted,followed by 3D laser scanning tests of shear-formed fractures.Test results demonstrated that the peak shear strength of intact granite is positively correlated with the normal stress,whereas it is negatively correlated with the temperature.The internal friction angle and cohesion of intact granite significantly decrease with an increase in the temperature.The anisotropy,roughness value,and height of the asperities on the fracture surfaces are reduced as the normal stress increases,whereas their variation trends are the opposite as the temperature increases.The macroscopic failure mode of intact granite under TM coupling conditions is dominated by mixed tensileeshear and shear failures.As the normal stress increases,intragranular fractures are developed ranging from a local to a global distribution,and the macroscopic failure mode of intact granite changes from mixed tensileeshear to shear failure.Finally,3D morphological characteristics of the asperities on the shear-formed fracture surfaces were analyzed,and a quadrangular pyramid conceptual model representing these asperities was proposed and sufficiently verified.
基金the German Research Foundation(DA 2255/1-1,to SCD).
文摘Morphological analyses are key outcome assessments for nerve regeneration studies but are historically limited to tissue sections.Novel optical tissue clearing techniques enabling three-dimensional imaging of entire organs at a subcellular resolution have revolutionized morphological studies of the brain.To extend their applicability to experimental nerve repair studies we adapted these techniques to nerves and their motor and sensory targets in rats.The solvent-based protocols rendered harvested peripheral nerves and their target organs transparent within 24 hours while preserving tissue architecture and fluorescence.The optical clearing was compatible with conventional laboratory techniques,including retrograde labeling studies,and computational image segmentation,providing fast and precise cell quantitation.Further,optically cleared organs enabled three-dimensional morphometry at an unprecedented scale including dermatome-wide innervation studies,tracing of intramuscular nerve branches or mapping of neurovascular networks.Given their wide-ranging applicability,rapid processing times,and low costs,tissue clearing techniques are likely to be a key technology for next-generation nerve repair studies.All procedures were approved by the Hospital for Sick Children’s Laboratory Animal Services Committee(49871/9)on November 9,2019.
基金National Natural Science Foundation of China,Grant/Award Numbers:51809290,51979093,52239009Project funded by Tibet Autonomous Region Key R&D Plan,Grant/Award Number:XZ202101ZY0002GPostgraduate Research&Practice Innovation Program of Jiangsu Province,Grant/Award Number:No.KYCX22_0656。
文摘This study aims to develop a high-precision and cost-efficient method for the threedimensional reconstruction of large particles in natural gravel and blasted rock fragments,utilizing Structure from Motion(SfM)and Multi-View Stereo(MVS)techniques.The proposed approach was applied to characterize the three-dimensional morphology of rockfill dam materials at a real construction site.Particle shape was quantitatively analyzed using shape indices of sphericity,convexity,and angularity.The predominant morphology of natural gravel is characterized as slightly elongated and slightly flat,while rock fragments are slightly elongated and not flat.Probability density distributions of shape indices follow a skewed normal distribution:sphericity and convexity show leftward skewness,whereas angularity is right-skewed.Skewness parameters of sphericity and angularity are consistent between natural gravel and blasted rock fragments,indicating comparable shape asymmetry.Convexity skewness is significantly higher in natural gravel compared to rock fragments,by approximately an order of magnitude.The relationship between size and particle shape shows that form ratios and associated shape descriptors change linearly with the logarithm of size;larger particles approach spherical or cubic forms.The innovative measurements contribute to the particle shape data set of rockfill dam materials,providing valuable insights into the three-dimensional and statistical morphological characteristics of relatively large particles in natural gravel and blasted rock fragments.This approach enhances understanding of particle morphology's impact on the mechanical behavior of granular materials.
基金Supported by the State administration of Traditional Secretary and the nanjing health Bureau,no.YKK12142
文摘AIM To assess the role of three-dimensional endoanal ultrasound (3D-EAUS) for morphological assessment of the anal sphincter of female patients with chronic proctalgia (CP). METHODS In this unmatched case control study, 30 consecutive female patients with CP and 25 normal women (control group) were enrolled. 3D-EAUS was performed in all subjects. Thickness and length of internal anal sphincter (IAS), thickness of puborectalis muscle (PR), length of the external anal sphincter (EAS) plus PR, and puborectalis angle were measured and compared between the two groups. RESULTS Patients with CP had significantly shorter IAS length and greater PR thickness, as compared to those in normal individuals (26.28 +/- 3.59 mm vs 28.87 +/- 4.84 mm, P < 0.05 and 9.67 +/- 1.57 mm vs 8.85 +/- 0.97 mm, P < 0.05, respectively). No significant between-group differences were observed with respect to IAS thickness and the EAS plus PR length (P > 0.05). Puborectalis angle in the CP group was significantly decreased, both in resting (88.23 degrees +/- 1.81 degrees vs 89.94 degrees +/- 2.07 degrees in control group, P < 0.05) and straining (88.47 degrees +/- 3.32 degrees vs 90.72 degrees +/- 1.87 degrees in control group, P < 0.05) phases, which suggest the presence of paradoxical contraction of PR in patients with CP. In the CP group, no significant difference in puborectalis angle was observed between the resting and straining phases (88.23 degrees +/- 1.81 degrees vs 88.47 degrees +/- 3.32 degrees respectively, P > 0.05). CONCLUSION The association of greater PR thickness and paradoxical contraction of PR with CP suggest their potential value as markers of CP.
基金Earmarked Research Grant (Hong Kong)(No.POLYU 5299/04E)
文摘A web camera based multi-camera convergent close-range photogrammetric system is developed to obtain the neonates＇ head and facial morphology. The data will then be used to develop a secure and good-fitting eye-patch protector for neonates, particularly whoa they are exposed to bright lights such as phototherapy light. Measurements obtained by the system are evaluated and validated against data obtained from optical scanning. Results show that the photogrammetric system meets the requirements of measuring accuracy and safety for neonate in the neonatal units.
文摘To evaluate the morphology of atrial septum by the live three-dimensional echocardiography （L3DE） and its value of clinical application, L3DE was performed in 62 subjects to observe the morphological characteristics and dynamic change of the overall anatomic structure of atrial septum. The study examined 49 patients with atrial septal defect （ASD）, including 3 patients with atrial septal aneurysm, and 10 healthy subjects. ASD in the 35 patients was surgically confirmed. The maximal diameters of ASD were measured and the percentages of area change were calculated. The parameters derived from L3DE were compared with intraoperative measurements. The results showed that L3DE could directly and clearly display the morphological features of overall anatomic structure of normal atrial septum, repaired and artificially-occluded atrial septum, atrial septal aneurysm. The defect area in ASD patients changed significantly during cardiac cycle, which reached a maximum at end-systole and a minimum at end-diastole, with a mean change percentage of 46.6%, ranging from 14.8% to 73.4%. The sizes obtained from L3DE bore an excellent correlation with intraoperative findings （r=0.90）. It is concluded that L3DE can clearly display the overall morphological features and dynamic change of atrial septum and measure the size of ASD area accurately, which is important in the decision to choose therapeutic protocols.
基金supported by the National Natural Science Foundation of China (No.51074019)
文摘A method for observing the three-dimensional morphologies of inclusions by deeply eroding a steel sample with a kind of organic solution composed of bromine water, acetone, and HCl （volume ratio, 45：45：10） was introduced. Four different kinds of inclusions in ultra low carbon steel were compared by metallographic observation and erosion observation. The results show that the three-dimensional morphologies of different kinds of inclusions could be observed clearly and simply after erosion. The method is useful for the observation and analysis of inclusions made by deep erosion. It also provides a new way to control and remove inclusions based on the true morphologies of inclusions.
基金sponsored by the National Natural Science Foundation of China,No. 30570628,30770751 and 81171089
文摘This study aimed to examine the differences in the morphological properties and proliferation of olfactory ensheathing cells in three-dimensional culture on collagen-heparan sulfate biological scaffolds and in two-dimensional culture on common flat culture plates. The proliferation rate of olfactory ensheathing cells in three-dimensional culture was higher than that in two-dimensional culture, as detected by an M-I-r assay. In addition, more than half of the olfactory ensheathing cells subcultured using the trypsinization method in three-dimensional culture displayed a spindly Schwann cell-like morphology with extremely long processes, while they showed a flat astrocyte-like morphology in two-dimensional culture. Moreover, spindle-shaped olfactory ensheathing cells tended to adopt an elongated bipolar morphology under both culture conditions. Experimental findings indicate that the morphological properties and proliferation of olfactory ensheathing cells in three-dimensional culture on collagen-heparan sulfate biological scaffolds are better than those in two-dimensional culture.
基金supported by the National Natural Science Foundation of China(32072980)Key Research and Development Projects in Tibet(XZ202001ZY0016N,XZ201902NB02,XZNKY-2019-C-053)。
文摘Fish morphological phenotypes are important resources in artificial breeding,functional gene mapping,and population-based studies in aquaculture and ecology.Traditional morphological measurement of phenotypes is rather expensive in terms of time and labor.More importantly,manual measurement is highly dependent on operational experience,which can lead to subjective phenotyping results.Here,we developed 3DPhenoFish software to extract fish morphological phenotypes from three-dimensional(3D)point cloud data.Algorithms for background elimination,coordinate normalization,image segmentation,key point recognition,and phenotype extraction were developed and integrated into an intuitive user interface.Furthermore,18 key points and traditional 2D morphological traits,along with 3D phenotypes,including area and volume,can be automatically obtained in a visualized manner.Intuitive fine-tuning of key points and customized definitions of phenotypes are also allowed in the software.Using 3DPhenoFish,we performed high-throughput phenotyping for four endemic Schizothoracinae species,including Schizopygopsis younghusbandi,Oxygymnocypris stewartii,Ptychobarbus dipogon,and Schizothorax oconnori.Results indicated that the morphological phenotypes from 3DPhenoFish exhibited high linear correlation(>0.94)with manual measurements and offered informative traits to discriminate samples of different species and even for different populations of the same species.In summary,we developed an efficient,accurate,and customizable tool,3DPhenoFish,to extract morphological phenotypes from point cloud data,which should help overcome traditional challenges in manual measurements.3DPhenoFish can be used for research on morphological phenotypes in fish,including functional gene mapping,artificial selection,and conservation studies.3DPhenoFish is an open-source software and can be downloaded for free at https://github.com/lyh24k/3DPhenoFish/tree/master.
基金supported by the National Science Fund for Distinguished Young Scholars(42225107)the National Natural Science Foundation of China(42001326,42371414,42171409,and 42271419)+1 种基金the Natural Science Foundation of Guangdong Province of China(2022A1515012207)the Basic and Applied Basic Research Project of Guangzhou Science and Technology Planning(202201011539)。
文摘Three-dimensional(3D)urban structures play a critical role in informing climate mitigation strategies aimed at the built environment and facilitating sustainable urban development.Regrettably,there exists a significant gap in detailed and consistent data on 3D building space structures with global coverage due to the challenges inherent in the data collection and model calibration processes.In this study,we constructed a global urban structure(GUS-3D)dataset,including building volume,height,and footprint information,at a 500 m spatial resolution using extensive satellite observation products and numerous reference building samples.Our analysis indicated that the total volume of buildings worldwide in2015 exceeded 1×10^(12)m^(3).Over the 1985 to 2015 period,we observed a slight increase in the magnitude of 3D building volume growth(i.e.,it increased from 166.02 km3 during the 1985–2000 period to 175.08km3 during the 2000–2015 period),while the expansion magnitudes of the two-dimensional(2D)building footprint(22.51×10^(3) vs 13.29×10^(3)km^(2))and urban extent(157×10^(3) vs 133.8×10^(3)km^(2))notably decreased.This trend highlights the significant increase in intensive vertical utilization of urban land.Furthermore,we identified significant heterogeneity in building space provision and inequality across cities worldwide.This inequality is particularly pronounced in many populous Asian cities,which has been overlooked in previous studies on economic inequality.The GUS-3D dataset shows great potential to deepen our understanding of the urban environment and creates new horizons for numerous 3D urban studies.
文摘To address the problem of multi-missile cooperative interception against maneuvering targets at a prespecified impact time and desired Line-of-Sight(LOS)angles in ThreeDimensional(3D)space,this paper proposes a 3D leader-following cooperative interception guidance law.First,in the LOS direction of the leader,an impact time-controlled guidance law is derived based on the fixed-time stability theory,which enables the leader to complete the interception task at a prespecified impact time.Next,in the LOS direction of the followers,by introducing a time consensus tracking error function,a fixed-time consensus tracking guidance law is investigated to guarantee the consensus tracking convergence of the time-to-go.Then,in the direction normal to the LOS,by combining the designed global integral sliding mode surface and the second-order Sliding Mode Control(SMC)theory,an innovative 3D LOS-angle-constrained interception guidance law is developed,which eliminates the reaching phase in the traditional sliding mode guidance laws and effectively saves energy consumption.Moreover,it effectively suppresses the chattering phenomenon while avoiding the singularity issue,and compensates for unknown interference caused by target maneuvering online,making it convenient for practical engineering applications.Finally,theoretical proof analysis and multiple sets of numerical simulation results verify the effectiveness,superiority,and robustness of the investigated guidance law.
基金funded by the National Natural Science F oundation of China(No.52172205)。
文摘Zinc oxide(ZnO)serves as a crucial functional semiconductor with a wide direct bandgap of approximately 3.37 eV.Solvothermal reaction is commonly used in the synthesis of ZnO micro/nanostructures,given its low cost,simplicity,and easy implementation.Moreover,ZnO morphology engineering has become desirable through the alteration of minor conditions in the reaction process,particularly at room temperature.In this work,ZnO micro/nanostructures were synthesized in a solution by varying the amounts of the ammonia added at low temperatures(including room temperature).The formation of Zn^(2+)complexes by ammonia in the precursor regulated the reaction rate of the morphology engineering of ZnO,which resulted in various structures,such as nanoparticles,nanosheets,microflowers,and single crystals.Finally,the obtained ZnO was used in the optoelectronic application of ultraviolet detectors.
基金funded by the National Science Centre,Poland,on the basis of the decision number UMO-2020/37/B/ST8/02097supported by the program“Excellence Initiative-Research University”for the AGH University of Krakow(IDUB AGH,No.501.696.7996,Action 4,ID 9880).
文摘Multicomponent Gd_(1−x)Sm_(x)Ba_(0.5)Sr_(0.5)CoCuO_(5+δ)double perovskites are optimized for application in terms of chemical composi-tion and morphology for the use as oxygen electrodes in solid oxide cells.Structural studies of other physicochemical properties are con-ducted on a series of materials obtained by the sol-gel method with different ratios of Gd and Sm cations.It is documented that changing the x value,and the resulting adjustment of the average ionic radius,have a significant impact on the crystal structure,stability,as well as on the total conductivity and thermomechanical properties of the materials,with the best results obtained for the Gd_(0.75)Sm_(0.2)5Ba_(0.5)Sr_(0.5)CoCuO_(5+δ)composition.Oxygen electrodes are prepared using the selected compound,allowing to obtain low polarization resistance values,such as 0.086Ω·cm^(2)at 800℃.Systematic studies of electrocatalytic activity are conducted using La_(0.8)Sr_(0.2)Ga_(0.8)Mg_(_(0.2))O_(3−δ)as the electrolyte for all electrodes,and Ce_(0.8)Gd_(0.2)O_(2−δ)electrolyte for the best performing Gd_(0.75)Sm_(0.2)5Ba_(0.5)Sr_(0.5)CoCuO_(5+δ)electrodes.The electrochemical data are analyzed using the distribution of relaxation times method.Also,the influence of the preparation method of the electrode material is in-ve`stigated using the electrospinning technique.Finally,the performance of the Gd_(0.75)Sm_(0.2)5Ba_(0.5)Sr_(0.5)CoCuO_(5+δ)electrodes is tested in a Ni-YSZ(yttria-stabilized zirconia)anode-supported cell with a Ce_(0.8)Gd_(0.2)O_(2−δ)buffer layer,in the fuel cell and electrolyzer operating modes.With the electrospun electrode,a power density of 462 mW·cm^(−2)is obtained at 700℃,with a current density of ca.0.2 A·cm^(−2)at 1.3 V for the electrolysis at the same temperature,indicating better performance compared to the sol-gel-based electrode.
基金supported by National Natural Science Foundation of China(Grant Nos.52305440,52204263)Natural Science Foundation of Changsha City(Grant Nos.kq2208272,kq2208274)+1 种基金Tribology Science Fund of the State Key Laboratory of Tribology in Advanced Equipment(Grant SKLTKF22B09)National Key Research and Development Program of China(2022YFB3706902).
文摘Laser-directed energy deposition(L-DED)is an advanced additive manufacturing technology primarily adopted in metal three-dimensional printing systems.The L-DED process is characterized by various defects,thus necessitating the extensive use of in-situ monitoring to enable real-time adjustments of process parameters by detecting molten-pool features.To address the challenge of accurately extracting the molten-pool morphology from an undetached spatter,an innovative monitoring method based on the U-Net(U-shaped network)is proposed herein.A lightweight architecture accelerates the processing speed,whereas an enhanced loss function incorporating weight maps augments the segmentation precision.The model performance is evaluated by comparing its segmentation accuracy and processing speed with those of the conventional U-Net,using the mean intersection over union(MIoU)as the segmentation metric.The improved model demonstrates superior segmentation accuracy at the interface between the molten pool and spatter,with a peak MIoU of 0.9798 achieved on the test set.Furthermore,this model processes each image in an extremely short time of 17.9 ms.Using this segmentation algorithm,the error in extracting the molten-pool width from single-track experiments is within 0.1 mm.The proposed method for monitoring the molten-pool morphology is suitable for deployment in online monitoring systems,thus providing a foundation for subsequent process-parameter regulation.
基金supported by the National Key Research and Development Program of China,No.2021ZD0202503(to AHT)the National Natural Science Foundation of China,Nos.31872759(to AHT)and 32070707(to CF)+1 种基金Shenzhen Science and Technology Program,No.RCJC20210609104333007(to ZW)Shenzhen-Hong Kong Institute of Brain Science,Shenzhen Fundamental Research Institutions,No.2021SHIBS0002(to ZW).
文摘Morphological alterations in dendritic spines have been linked to changes in functional communication between neurons that affect learning and memory.Kinesin-4 KIF21A helps organize the microtubule-actin network at the cell cortex by interacting with KANK1;however,whether KIF21A modulates dendritic structure and function in neurons remains unknown.In this study,we found that KIF21A was distributed in a subset of dendritic spines,and that these KIF21A-positive spines were larger and more structurally plastic than KIF21A-negative spines.Furthermore,the interaction between KIF21A and KANK1 was found to be critical for dendritic spine morphogenesis and synaptic plasticity.Knockdown of either KIF21A or KANK1 inhibited dendritic spine morphogenesis and dendritic branching,and these deficits were fully rescued by coexpressing full-length KIF21A or KANK1,but not by proteins with mutations disrupting direct binding between KIF21A and KANK1 or binding between KANK1 and talin1.Knocking down KIF21A in the hippocampus of rats inhibited the amplitudes of long-term potentiation induced by high-frequency stimulation and negatively impacted the animals’cognitive abilities.Taken together,our findings demonstrate the function of KIF21A in modulating spine morphology and provide insight into its role in synaptic function.
文摘Liposarcoma is one of the most common soft tissue sarcomas,however,its occurrence rate is still rare compared to other cancers.Due to its rarity,in vitro experiments are an essential approach to elucidate liposarcoma pathobiology.Conventional cell culture-based research(2D cell culture)is still playing a pivotal role,while several shortcomings have been recently under discussion.In vivo,mouse models are usually adopted for pre-clinical analyses with expectations to overcome the issues of 2D cell culture.However,they do not fully recapitulate human dedifferentiated liposarcoma(DDLPS)characteristics.Therefore,three-dimensional(3D)culture systems have been the recent research focus in the cell biology field with the expectation to overcome at the same time the disadvantages of 2D cell culture and in vivo animal models and fill in the gap between them.Given the liposarcoma rarity,we believe that 3D cell culture techniques,including 3D cell cultures/co-cultures,and Patient-Derived tumor Organoids(PDOs),represent a promising approach to facilitate liposarcoma investigation and elucidate its molecular mechanisms and effective therapy development.In this review,we first provide a general overview of 3D cell cultures compared to 2D cell cultures.We then focus on one of the recent 3D cell culture applications,Patient-Derived Organoids(PDOs),summarizing and discussing several PDO methodologies.Finally,we discuss the current and future applications of PDOs to sarcoma,particularly in the field of liposarcoma.
基金supported by the National Science Foundation under Grant No.2327916.
文摘The sedimentary bed morphology modulated by the wake flow of a wall-mounted flexible aquatic vegetation blade across various structural aspect ratios(A_(R)=l/b,where l and b are the length and width of the blade,respectively)and incoming flow velocities was experimentally investigated in a water channel.A surface scanner was implemented to quantify bed topography,and a tomographic particle image velocimetry system was used to characterize the three-dimensional wake flows.The results showed that due to the deflection of incoming flow,the velocity magnitude increased at the lateral sides of the blade,thereby producing distinctive symmetric scour holes in these regions.The normalized morphology profiles of the sedimentary bed,which were extracted along the streamwise direction at the location of the maximum erosion depth,exhibited a self-similar pattern that closely followed a sinusoidal wave profile.The level of velocity magnitude enhancement was highly correlated to the postures of the flexible blade.At a given flow velocity,the blade with lower aspect ratios exhibited less significant deformation,causing more significant near-bed velocity enhancement in the wake deflection zone and therefore leading to higher erosion volumes.Further investigation indicated that when the blade underwent slight deformation,the larger velocity enhancement close to the bed can be attributed to more significant flow deflection effects at the lateral sides of the blade and stronger flow mixing with high momentum flows away from the bed.Supported with measurements,a basic formula was established to quantify the shear stress acting on the sedimentary bed as a function of incoming flow velocity and blade aspect ratio.
