It has previously been shown that aerodynamic roughness length changes significantly along with near- surface atmospheric thermodynamic state; however, at present, this phenomenon remains poorly understood, and very l...It has previously been shown that aerodynamic roughness length changes significantly along with near- surface atmospheric thermodynamic state; however, at present, this phenomenon remains poorly understood, and very little research concerning this topic has been conducted. In this paper, by using the data of different underlying surfaces provided by the Experimental Co-observation and Integral Research in Semi-arid and Arid Regions over North China, aerodynamic roughness length （z0） values in stable, neutral, and unstable atmospheric stratifications are compared with one another, and the relationship between z0 and atmospheric thermodynamic stability （（） is analyzed. It is found that z0 shows great differences among the stable, neutral, and unstable atmospheric thermodynamic states, with the difference in z0 values between the fully thermodynamic stable condition and the neutral condition reaching 60% of the mean z0. F^trthermore, for the wind speed range in which the wind data are less sensitive to z0, the surface z0 changes more significantly with （, and is highly correlated with both the Monin-Obukhov stability （4o） and the overall Richardson number （Rib）, with both of their correlation coefficients greater than 0.71 and 0.47 in the stable and unstable atmospheric stratification, respectively. The empirical relation fitted with the experimental observations is quite consistent with the Zilitinkevich theoretical relation in the stable atmosphere, but the two are quite distinct and even show opposite variation tendencies in the unstable atmosphere. In application, however, verification of the empirical fitted relations by using the experimental data finds that the fitted relation is slightly more applicable than the Zilitinkevich theoretical relation in stable atmospheric stratification, but it is much more suitable than the Zilitinkevich relation in unstable atmospheric stratification.展开更多
In order to find out the sensitivity of the thermophysical and structural parameters to the thermodynamic characteristics of twin-tube hydraulic shock absorbers,based on the bench test,a method for calculating the tim...In order to find out the sensitivity of the thermophysical and structural parameters to the thermodynamic characteristics of twin-tube hydraulic shock absorbers,based on the bench test,a method for calculating the time-varying rate of the external work on the shock absorber oil is proposed.And then,a thermodynamic model of the twin-tube hydraulic shock absorber is established by using the basic thermodynamic principles.By analyzing the influence of each parameter on the thermodynamic characteristics of the shock absorber,it can be seen that,the radius of the working cylinder outer wall has the greatest influence on the temperature rise of the shock absorber,followed by the thermal conductivity of the oil,the height of the oil,the heat transfer length of the cylinder barrel,the radius of the oil storage cylinder outer wall,the emissivity of the oil storage cylinder outer wall,the height of the nitrogen,the thermal conductivity of the nitrogen,the specific heat capacity of the oil,the density of the oil,the thermal conductivity of the cylinder,and the mass of the working oil.The kinematic viscosity of the oil has the least influence on the temperature rise of the shock absorber.The research can provide an effective theoretical guidance and reference for the design of the twin-tube hydraulic shock absorber.展开更多
Thermodynamic characteristics are of great importance for the performance of a high-temperature flow-rate control valve,as high-temperature environment may bring problems,such as blocking of spool and increasing of le...Thermodynamic characteristics are of great importance for the performance of a high-temperature flow-rate control valve,as high-temperature environment may bring problems,such as blocking of spool and increasing of leakage,to the valve.In this paper,a high-temperature flow-rate control valve,pilot-controlled by a pneumatic servo system is developed to control the fuel supply for scramjet engines.After introducing the construction and working principle,the thermodynamic mathematical models of the valve are built based on the heat transfer methods inside the valve.By using different boundary conditions,different methods of simulations are carried out and compared.The steady-state and transient temperature field distribution inside the valve body are predicted and temperatures at five interested points are measured.By comparing the simulation and experimental results,a reasonable 3D finite element analysis method is suggested to predict the thermodynamic characteristics of the high-temperature flow-rate control valve.展开更多
This study aims at explaining the relationship between thermodynamic characteristics and direction of rotation of mesoscale eddies（MEs）. The geometric characteristics of the MEs are under the following assumptions：...This study aims at explaining the relationship between thermodynamic characteristics and direction of rotation of mesoscale eddies（MEs）. The geometric characteristics of the MEs are under the following assumptions： the structure of the MEs is symmetrical, and changes of oceanic physical variables are close to linear features in the radial direction in the ME regions. Based on these assumptions, by using primitive equations without friction under a cylindrical coordinate system, the thermodynamic characteristics of the MEs are derived, showing that the conventional relationship of warm anticyclonic eddies with high sea surface height（SSH） and cold cyclonic eddies with low SSH is not consistent with the SSH and sea surface temperature（SST） observations of eddies. The results show that the symmetrical form is an ideal approximation for the geometric characteristics of MEs. In consideration of the above assumptions, there are advantages for derivation of the characteristics of the MEs under a cylindrical coordinate.展开更多
In this study a Cu_(43)Zr_(48)Al_(9)bulk metallic glass prepared by the copper mold casting method is considered.In recent years,Cu-Zr-Al systems like this have enjoyed widespread attention due to their high strength,...In this study a Cu_(43)Zr_(48)Al_(9)bulk metallic glass prepared by the copper mold casting method is considered.In recent years,Cu-Zr-Al systems like this have enjoyed widespread attention due to their high strength,high hardness,high corrosion resistance and low cost.Here samples of this substance are studied using DSC(Differential scanning calorimetry)to determine the effect of different test conditions(heating rate,sample mass,sample specific surface area and sample crystal phase)on the characteristic thermodynamic temperature of the bulk metallic glass.Experimental results show that almost all of the five characteristic thermodynamic temperatures(T_(g),T_(x),T_(p),T_(m),T_(l))of this substance have higher values when the heating rate is increased.The influence of the variation of sample mass,sample specific surface area and sample crystal phase on the amorphous alloy characteristic temperature is very weak.lower the heating rate,the more developed the crystalline phase in the amorphous alloy will be.展开更多
This paper systematically reports the thermodynamic characteristic and phase evolution of immiscible Cr–Mo binary alloy during mechanical alloying（MA） process. The Cr–35Mo（in at%） powder mixture was milled at 24...This paper systematically reports the thermodynamic characteristic and phase evolution of immiscible Cr–Mo binary alloy during mechanical alloying（MA） process. The Cr–35Mo（in at%） powder mixture was milled at 243 and258 K, respectively, for different time. For comparative study, Cr–15Mo and Cr–62Mo powder mixtures were milled at 243 K for 18 h. Solid solution Cr（Mo） with body-centered cubic（bcc） crystal structure and amorphous Cr（Mo） alloy was obtained during MA process caused by high-energy ball milling. Based on the Miedema＇s model, the free-energy change for forming either a solid solution or an amorphous in Cr–Mo alloy system is positive but small at a temperature range between 200 and 300 K. The thermodynamical barrier for forming alloy in Cr–Mo system can be overcome when MA occurs at 243 K, and the supersaturated solid solution crystal nuclei with bcc structure form continually, and three supersaturated solid solutions of Cr–62Mo, Cr–35Mo and Cr–15Mo formed. Milling the Cr–35Mo powder mixture at 258 K, the solid solution Cr（Mo） forms firstly, and then the solid solution Cr（Mo） transforms into the amorphous Cr（Mo）alloy with a few of nanocrystallines when milling is prolonged. At higher milling temperature, it is favorable for the formation of the amorphous phase, as indicated by the thermodynamical calculation for immiscible Cr–Mo alloy system.展开更多
The southern branch trough (SBT) mainly appears in the winter half year (November to May of the following year), using the 4 times daily NCEP/NCAR re-analysis data nearly 41 years (1979-2019) to analyze the difference...The southern branch trough (SBT) mainly appears in the winter half year (November to May of the following year), using the 4 times daily NCEP/NCAR re-analysis data nearly 41 years (1979-2019) to analyze the differences of the SBT distribution of spatial location, frequency in winter and spring, then selects the “eastern type” and “western type” of the 10 most typical SBT, using simplified vertical vorticity tendency equation, using simplified vertical vorticity tendency equation to diagnosis of the SBT in power, heat, water vapor and wave energy in different positions. The results show that: 1) The location of the SBT is more eastward in winter, and more westward in spring. 2) The diagnosis results of the vorticity equation show that the vorticity of the southern branch of the “western type” is mainly contributed by advection term;the vorticity of the “eastern type” south branch is mainly contributed by the non-adiabatic heating term. 3) The SBT of the “eastern type” has more obvious vorticity advection than the southern branch of the “western type”, and the dynamic action is stronger. The “western type” SBT has stronger Q1, specific humidity advection and water vapor flux than the “eastern type” SBT, which is greatly affected by thermal action and water vapor. When the “eastern type” and “western type” SBT occur, the T-N wave activity flux appears obvious abnormal energy fluctuation propagation.展开更多
Based on theory of variable-mass system thermodynamics, the dynamic mathematic models of each component of the horizontal steam-launch system were established, and by the numerical simulation of the system launching p...Based on theory of variable-mass system thermodynamics, the dynamic mathematic models of each component of the horizontal steam-launch system were established, and by the numerical simulation of the system launching process, the thermodynamics and kinetics characteristics of the system with three valves of different flow characteristics were got. The simulation results show that the values of the peak-to-average ratios of dimensionless acceleration with the equal percentage valve, the linear valve and the quick opening valve are 1.355, 1.614 and 1.722, respectively, and the final values of the dimensionless velocities are 0.843, 0.957 and 1.0, respectively. In conclusion, the value of the dimensionless velocity with the equal percentage valve doesn't reach the set value of 0.90 when the dimensionless displacement is 0.82, while the system with the linear valve can meet the launching requirement, as well as the fluctuation range of dimensionless acceleration is less than that of the quick opening valve. Therefore, the system with the linear valve has the best performance among the three kinds of valves.展开更多
基金Supported by the National Natural Science Foundation of China (40830957, 41075008, and 41075009)National Basic Research and Development (973) Program of China (2013CB430206)China Postdoctoral Science Foundation (20110490854)
文摘It has previously been shown that aerodynamic roughness length changes significantly along with near- surface atmospheric thermodynamic state; however, at present, this phenomenon remains poorly understood, and very little research concerning this topic has been conducted. In this paper, by using the data of different underlying surfaces provided by the Experimental Co-observation and Integral Research in Semi-arid and Arid Regions over North China, aerodynamic roughness length （z0） values in stable, neutral, and unstable atmospheric stratifications are compared with one another, and the relationship between z0 and atmospheric thermodynamic stability （（） is analyzed. It is found that z0 shows great differences among the stable, neutral, and unstable atmospheric thermodynamic states, with the difference in z0 values between the fully thermodynamic stable condition and the neutral condition reaching 60% of the mean z0. F^trthermore, for the wind speed range in which the wind data are less sensitive to z0, the surface z0 changes more significantly with （, and is highly correlated with both the Monin-Obukhov stability （4o） and the overall Richardson number （Rib）, with both of their correlation coefficients greater than 0.71 and 0.47 in the stable and unstable atmospheric stratification, respectively. The empirical relation fitted with the experimental observations is quite consistent with the Zilitinkevich theoretical relation in the stable atmosphere, but the two are quite distinct and even show opposite variation tendencies in the unstable atmosphere. In application, however, verification of the empirical fitted relations by using the experimental data finds that the fitted relation is slightly more applicable than the Zilitinkevich theoretical relation in stable atmospheric stratification, but it is much more suitable than the Zilitinkevich relation in unstable atmospheric stratification.
基金supported by the National Natural Science Foundation of China(51575325).
文摘In order to find out the sensitivity of the thermophysical and structural parameters to the thermodynamic characteristics of twin-tube hydraulic shock absorbers,based on the bench test,a method for calculating the time-varying rate of the external work on the shock absorber oil is proposed.And then,a thermodynamic model of the twin-tube hydraulic shock absorber is established by using the basic thermodynamic principles.By analyzing the influence of each parameter on the thermodynamic characteristics of the shock absorber,it can be seen that,the radius of the working cylinder outer wall has the greatest influence on the temperature rise of the shock absorber,followed by the thermal conductivity of the oil,the height of the oil,the heat transfer length of the cylinder barrel,the radius of the oil storage cylinder outer wall,the emissivity of the oil storage cylinder outer wall,the height of the nitrogen,the thermal conductivity of the nitrogen,the specific heat capacity of the oil,the density of the oil,the thermal conductivity of the cylinder,and the mass of the working oil.The kinematic viscosity of the oil has the least influence on the temperature rise of the shock absorber.The research can provide an effective theoretical guidance and reference for the design of the twin-tube hydraulic shock absorber.
文摘Thermodynamic characteristics are of great importance for the performance of a high-temperature flow-rate control valve,as high-temperature environment may bring problems,such as blocking of spool and increasing of leakage,to the valve.In this paper,a high-temperature flow-rate control valve,pilot-controlled by a pneumatic servo system is developed to control the fuel supply for scramjet engines.After introducing the construction and working principle,the thermodynamic mathematical models of the valve are built based on the heat transfer methods inside the valve.By using different boundary conditions,different methods of simulations are carried out and compared.The steady-state and transient temperature field distribution inside the valve body are predicted and temperatures at five interested points are measured.By comparing the simulation and experimental results,a reasonable 3D finite element analysis method is suggested to predict the thermodynamic characteristics of the high-temperature flow-rate control valve.
基金The Junior Fellowships for CAST Advanced Innovation Think-tank Program“Evaluation of the Oceanic Dynamic Resources of the 21st Century Maritime Silk Road and Its Strategic Points”under contract No.DXB-ZKQN-2016-019the National Key Basic Research Development Program Astronomy and Earth Factor on the Impact of Climate Change under contract No.2013CB956200+1 种基金the National Natural Science Foundation of China under contract No.41275086the Natural Science Foundation of Shandong Province under contract No.ZR2016DL09
文摘This study aims at explaining the relationship between thermodynamic characteristics and direction of rotation of mesoscale eddies（MEs）. The geometric characteristics of the MEs are under the following assumptions： the structure of the MEs is symmetrical, and changes of oceanic physical variables are close to linear features in the radial direction in the ME regions. Based on these assumptions, by using primitive equations without friction under a cylindrical coordinate system, the thermodynamic characteristics of the MEs are derived, showing that the conventional relationship of warm anticyclonic eddies with high sea surface height（SSH） and cold cyclonic eddies with low SSH is not consistent with the SSH and sea surface temperature（SST） observations of eddies. The results show that the symmetrical form is an ideal approximation for the geometric characteristics of MEs. In consideration of the above assumptions, there are advantages for derivation of the characteristics of the MEs under a cylindrical coordinate.
基金This work was supported financially by the President Fund of Xi’an Technological University(No.0852-302021407).
文摘In this study a Cu_(43)Zr_(48)Al_(9)bulk metallic glass prepared by the copper mold casting method is considered.In recent years,Cu-Zr-Al systems like this have enjoyed widespread attention due to their high strength,high hardness,high corrosion resistance and low cost.Here samples of this substance are studied using DSC(Differential scanning calorimetry)to determine the effect of different test conditions(heating rate,sample mass,sample specific surface area and sample crystal phase)on the characteristic thermodynamic temperature of the bulk metallic glass.Experimental results show that almost all of the five characteristic thermodynamic temperatures(T_(g),T_(x),T_(p),T_(m),T_(l))of this substance have higher values when the heating rate is increased.The influence of the variation of sample mass,sample specific surface area and sample crystal phase on the amorphous alloy characteristic temperature is very weak.lower the heating rate,the more developed the crystalline phase in the amorphous alloy will be.
基金National Natural Science Foundation of China (Nos. 51271143 and 51302247)
文摘This paper systematically reports the thermodynamic characteristic and phase evolution of immiscible Cr–Mo binary alloy during mechanical alloying（MA） process. The Cr–35Mo（in at%） powder mixture was milled at 243 and258 K, respectively, for different time. For comparative study, Cr–15Mo and Cr–62Mo powder mixtures were milled at 243 K for 18 h. Solid solution Cr（Mo） with body-centered cubic（bcc） crystal structure and amorphous Cr（Mo） alloy was obtained during MA process caused by high-energy ball milling. Based on the Miedema＇s model, the free-energy change for forming either a solid solution or an amorphous in Cr–Mo alloy system is positive but small at a temperature range between 200 and 300 K. The thermodynamical barrier for forming alloy in Cr–Mo system can be overcome when MA occurs at 243 K, and the supersaturated solid solution crystal nuclei with bcc structure form continually, and three supersaturated solid solutions of Cr–62Mo, Cr–35Mo and Cr–15Mo formed. Milling the Cr–35Mo powder mixture at 258 K, the solid solution Cr（Mo） forms firstly, and then the solid solution Cr（Mo） transforms into the amorphous Cr（Mo）alloy with a few of nanocrystallines when milling is prolonged. At higher milling temperature, it is favorable for the formation of the amorphous phase, as indicated by the thermodynamical calculation for immiscible Cr–Mo alloy system.
文摘The southern branch trough (SBT) mainly appears in the winter half year (November to May of the following year), using the 4 times daily NCEP/NCAR re-analysis data nearly 41 years (1979-2019) to analyze the differences of the SBT distribution of spatial location, frequency in winter and spring, then selects the “eastern type” and “western type” of the 10 most typical SBT, using simplified vertical vorticity tendency equation, using simplified vertical vorticity tendency equation to diagnosis of the SBT in power, heat, water vapor and wave energy in different positions. The results show that: 1) The location of the SBT is more eastward in winter, and more westward in spring. 2) The diagnosis results of the vorticity equation show that the vorticity of the southern branch of the “western type” is mainly contributed by advection term;the vorticity of the “eastern type” south branch is mainly contributed by the non-adiabatic heating term. 3) The SBT of the “eastern type” has more obvious vorticity advection than the southern branch of the “western type”, and the dynamic action is stronger. The “western type” SBT has stronger Q1, specific humidity advection and water vapor flux than the “eastern type” SBT, which is greatly affected by thermal action and water vapor. When the “eastern type” and “western type” SBT occur, the T-N wave activity flux appears obvious abnormal energy fluctuation propagation.
基金Project(20080431380)supported by the National Postdoctoral Science Foundation,China
文摘Based on theory of variable-mass system thermodynamics, the dynamic mathematic models of each component of the horizontal steam-launch system were established, and by the numerical simulation of the system launching process, the thermodynamics and kinetics characteristics of the system with three valves of different flow characteristics were got. The simulation results show that the values of the peak-to-average ratios of dimensionless acceleration with the equal percentage valve, the linear valve and the quick opening valve are 1.355, 1.614 and 1.722, respectively, and the final values of the dimensionless velocities are 0.843, 0.957 and 1.0, respectively. In conclusion, the value of the dimensionless velocity with the equal percentage valve doesn't reach the set value of 0.90 when the dimensionless displacement is 0.82, while the system with the linear valve can meet the launching requirement, as well as the fluctuation range of dimensionless acceleration is less than that of the quick opening valve. Therefore, the system with the linear valve has the best performance among the three kinds of valves.
