Specialized vanadium(V)-iron(Fe)-based alloy additives utilized in the production of V-containing steels were investigated.Vanadium slag from the Panzhihua region of China was utilized as a raw material to optimize pr...Specialized vanadium(V)-iron(Fe)-based alloy additives utilized in the production of V-containing steels were investigated.Vanadium slag from the Panzhihua region of China was utilized as a raw material to optimize process parameters for the preparation of V-Fe-based alloy via silicon thermal reduction.Experiments were conducted to investigate the effects of reduction temperature,holding time,and slag composition on alloy-slag separation,alloy microstructure,and the oxide content of residual slag,with an emphasis on the recovery of valuable metal elements.The results indicated that the optimal process conditions for silicon thermal reduction were achieved at reduction temperature of 1823 K,holding time of 240 min,and slag composition of 45 wt.%SiO_(2),40 wt.%CaO,and 15 wt.%Al_(2)O_(3).The resulting V-Fe-based alloy predominantly consisted of Fe-based phases such as Fe,titanium(Ti),silicon(Si)and manganese(Mn),with Si,V,as well as chromium(Cr)concentrated in the intercrystalline phase of the Fe-based alloy.The recoveries of Fe,Mn,Cr,V,and Ti under the optimal conditions were 96.30%,91.96%,86.53%,80.29%,and 74.82%,respectively.The key components of the V-Fe-based alloy obtained were 41.96 wt.%Si,27.55 wt.%Fe,12.13 wt.%Mn,5.53 wt.%V,4.86 wt.%Cr,and 3.74 wt.%Ti,thereby enabling the comprehensive recovery of the valuable metal from vanadium slag.展开更多
Transparent conductive graphene films are fabricated by the transfer printing of graphene aqueous dispersion followed by hydrohalic acids and thermal reduction. Results indicate that the graphene film reduced by hydro...Transparent conductive graphene films are fabricated by the transfer printing of graphene aqueous dispersion followed by hydrohalic acids and thermal reduction. Results indicate that the graphene film reduced by hydroiodic acid （HI） reduction combined with thermal treatment shows a higher electrical conductivity than that reduced only by thermal treatment at the same transparency. A film with a sheet resistance of - 2400 D./sq at a transparency over 72% is obtained at a typical wavelength of 550 nm.展开更多
Up to now, the Pedgion magnesium reduction process is the dominating magnesium production process. In 2004, about 98% of raw magnesium is produced by Pedgion magnesium reduction process in China which equals to 60% of...Up to now, the Pedgion magnesium reduction process is the dominating magnesium production process. In 2004, about 98% of raw magnesium is produced by Pedgion magnesium reduction process in China which equals to 60% of the global output. It shows that the dolomite-ferrosilicon thermal reduction process is the most important method to produce magnesium in the world. Limited by the disadvantage of dolomite-ferrosilicon thermal reduction process, the magnesium producing process always followed by relatively severe pollution, while the resource utilizing efficiency keeps very low. With the rapid development of dolomite-ferrosilicon thermal reduction process in China, many research works have been done aiming at the process technology and the reduction theory, and the magnesium producing process has got great evolution. The history of dolomite-ferrosilicon thermal reduction process was introduced; the process character, the merits and which defects were also discussed. Defects in dolomite-ferrosilicon thermal reduction process were expatiated, and feasible method and idea to upgrade the process was put forward. The main problems and the potential troubles hindering the development of magnesium industry were analyzed. Finally, the probability to further improve the thermal reduction process and the effective approaches to develop Chinese magnesium industry were discussed.展开更多
The organic gel-thermal reduction process was successfully used for the preparation of magnetic metal Ni, Fe, Fe-Ni fine fibers from raw materials of citric acid or lactic acid and metal salts. Ni, Fe and Fe-Ni fine f...The organic gel-thermal reduction process was successfully used for the preparation of magnetic metal Ni, Fe, Fe-Ni fine fibers from raw materials of citric acid or lactic acid and metal salts. Ni, Fe and Fe-Ni fine fibers synthesized were featured with diameters of around 1 μm and lengths of as long as 2 m for Ni fibers, 0.5 m for iron fibers, 1 m for Fe-Ni fibers. The structure, thermal decomposition process and morphologies of the gel precursors and fibers derived from thermal reduction of these gel precursors were characterized by FTIR, XRD,TG/DSC and SEM, respectively. The gel spinnability largely depends on molecular structures of metal-carboxylate complexes formed in the gel. It is reasoned that these gels consist of linear-type structural molecules [（C6H6O7）Ni]n or [（C6H5O7）2Ni3] for the nickel citrate gel, [（C3H5O3）3Fe] for the ferric lactate gel, [（C6H5O7）5（NiFe）3] for the iron-nickel citrate gel respectively and the gels obtain showed a good spinning performance.展开更多
The organic gel-thermal reduction process was used for the preparation of ferromagnetic metal Ni, Co and Fe fine fibers from the raw materials of citric acid, lactic acid and metal salts. The structure, thermal decomp...The organic gel-thermal reduction process was used for the preparation of ferromagnetic metal Ni, Co and Fe fine fibers from the raw materials of citric acid, lactic acid and metal salts. The structure, thermal decomposition process and morphologies of the gel precursors and fibers derived from thermal reduction of these gel precursors were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, thermo-gravimetric/differential scanning calorimetry and scanning electron microscopy. The results show that spinnability of gel largely depends on molecular structure of metal-carboxylate complex that is a linear-type structure formed in the gel. As a result, the gels exhibit a good spinnability. Metal Ni, Co and Fe fine fibers are featured with diameters of around 1 μm and a high aspect ratio up to 1×106.展开更多
High-entropy nitride powders are one of prerequisite materials for the preparation of high-performance high-entropy nitride ceramics.In this paper,high-entropy(HfZrTiNbTa)N powders were synthesized via nitride(i.e.,si...High-entropy nitride powders are one of prerequisite materials for the preparation of high-performance high-entropy nitride ceramics.In this paper,high-entropy(HfZrTiNbTa)N powders were synthesized via nitride(i.e.,silicon nitride(Si_(3)N_(4)))thermal reduction with soft mechanochemical assistance.The results show that metal oxides like hafnium dioxide(HfO_(2)),zirconium dioxide(ZrO_(2)),titanium dioxide(TiO_(2)),niobium pentoxide(Nb_(2)O_(5)),and tantalum pentoxide(Ta_(2)O_(5))can all be transformed into the corresponding metal nitrides in the presence of Si_(3)N_(4)at 1700℃,and solid solution of the metal nitrides can be formed as the temperature increases to 2100℃.The high-entropy(HfZrTiNbTa)N powders with submicron-sized particles,a narrower size distribution,and a single face-centered cubic(fcc)structure are obtained from raw material mixtures ground for 10 h and subsequently sintered at 1800℃.In addition,the high-entropy bulk nitride ceramics with relative density(Rw)of 94.31%±0.76%,Vickers hardness of 21.00±0.94 GPa,and fracture toughness(KIC)of 3.18±0.16 MPa·m1/2 are obtained with submicron-sized powders,which are superior to those obtained with micron-sized powders.展开更多
Final electromagnetic stirring(F-EMS)and thermal soft reduction(TSR)are techniques that improve the inner quality of continuous casting billets,but they have rarely been applied simultaneously.The application effects ...Final electromagnetic stirring(F-EMS)and thermal soft reduction(TSR)are techniques that improve the inner quality of continuous casting billets,but they have rarely been applied simultaneously.The application effects of F-EMS and TSR were compared,and a process integrating F-EMS and TSR was adopted for a billet continuous caster.A heat transfer model was established to calculate the thermal behavior of 82A tire cord steel billet.The locations of F-EMS and TSR were determined,followed by conducting a series of plant trials,involving F-EMS alone,TSR alone,and the integrated process of F-EMS and TSR.The results showed that F-EMS or TSR could effectively improve the inner quality of the billet under their respective suitable working conditions.Moreover,F-EMS was found to be more helpful in terms of improving central segregation,while TSR tended to improve V-segregation,central porosity,and pipe.The integration of F-EMS and TSR allowed the advantages of each technique to be utilized,thereby better improving the inner quality.Among all the working conditions,82A steel billet showed optimum inner quality when the current of F-EMS was 240 A and the cooling intensity of TSR was 2.2 m^(3) h^(−1).These findings demonstrate that the integration of F-EMS and TSR is promising for application on continuous casting billets.展开更多
A new process of producing magnesium by thermal vacuum reduction using dolomite and magnesite as materials and silicocalcium as reductant was studied in this study. The reduction process of MgO by silicocalcium was an...A new process of producing magnesium by thermal vacuum reduction using dolomite and magnesite as materials and silicocalcium as reductant was studied in this study. The reduction process of MgO by silicocalcium was analyzed by phases analysis of reduction slag through X-ray diffraction （XRD） and the factors influencing the reduction ratio of MgO were investigated. The experi- mental results show that when using silicocalcium as reductant, the reduction ratio of MgO can be over 93 %. In the reduction process, calcium in silicocalcium takes part in the reduction reaction of MgO firstly below 1,000 ℃ and it makes CaSi2 decompose. It also releases elemental silicon which has more reactive activity and improves the reduction reaction of MgO. That is the main cause that the reduction ratio of MgO using silicocalcium as reductant is 8 %-10 % higher than that by Pidgeon process using fer- rosilicon as reductant under the same conditions.展开更多
Titanium exhibits outstanding properties,particularly,high specific strength and resistance to both high and low temperatures,earning it a reputation as the metal of the future.However,because of the highly reactive n...Titanium exhibits outstanding properties,particularly,high specific strength and resistance to both high and low temperatures,earning it a reputation as the metal of the future.However,because of the highly reactive nature of titanium,metallic titanium production involves extensive procedures and high costs.Considering its advantages and limitations,the European Union has classified titanium metal as a critical raw material(CRM)of low category.The Kroll process is predominantly used to produce titanium;however,molten salt electrolysis(MSE)is currently being explored for producing metallic titanium at a low cost.Since 2000,electrolytic titanium production has undergone a wave of technological advancements.However,because of the intermediate and disproportionation reactions in the electrolytic titanium production process,the process efficiency and titanium purity according to industrial standards could not be achieved.Consequently,metallic titanium production has gradually diversified into employing technologies such as thermal reduction,MSE,and titanium alloy preparation.This study provides a comprehensive review of research advances in titanium metal preparation technologies over the past two decades,highlighting the challenges faced by the existing methods and proposing potential solutions.It offers useful insights into the development of low-cost titanium preparation technologies.展开更多
The kinetics of isothermal reduction of Ag2O with graphite under argon atmosphere for a non-activated sample and mechanically activated sample was investigated.It is found that Johnson-Mehl-Avrami model appropriately ...The kinetics of isothermal reduction of Ag2O with graphite under argon atmosphere for a non-activated sample and mechanically activated sample was investigated.It is found that Johnson-Mehl-Avrami model appropriately explained the thermal and mechanochemical synthesis of Ag from Ag2O＋ghraphite mixture.The process kinetics was investigated using the same approach for milled and unmilled samples.The results show that the Avrami exponent of mechanochemical reduction is higher than that of high temperature thermal reduction.Also,the mechanisms of nuclei growth in thermal and mechanochemical reduction are diffusion controlled and interface controlled,respectively.展开更多
Hafnium carbonitride(HfC_(x)N_(1-x))ceramics have drawn considerable interest due to their exceptional me-chanical and thermophysical properties.Herein,we report a novel single-source precursor with Hf-N bonds as the ...Hafnium carbonitride(HfC_(x)N_(1-x))ceramics have drawn considerable interest due to their exceptional me-chanical and thermophysical properties.Herein,we report a novel single-source precursor with Hf-N bonds as the main chain and fabricate HfC_(x)N_(1-x)ceramics after pyrolysis of the precursor.The synthesis,ceramic conversion,and microstructural evolution of the single-source precursor as well as the derived HfC_(x)N_(1-x)ceramics treated under various atmospheres were investigated.The results indicate that in an argon atmosphere,the nitrogen content within HfC_(x)N_(1-x)decreases with rising temperature.While under a nitrogen atmosphere,the high concentration of N_(2)facilitates the rapid conversion of HfO2 to Hf7O8N4,which subsequently promotes the transformation of the HfC_(x)N_(1-x)solid solution ceramics.During this process,there is also an inhibitory effect of N_(2)on the tendency of HfN into HfC.Moreover,the desired chemical composition of HfC_(x)N_(1-x)can be regulated by adjusting the N_(2)concentration in the heat treat-ment atmosphere.The present work proposes a novel strategy for the single-source precursor-derived carbonitride ceramics and provides a deep understanding of the preparation and property modulation of HfC_(x)N_(1-x)ceramics.展开更多
Monolayer ultra-large graphene oxide （UL-GO） sheets with diameter up to about 100 μm were synthesized based on a chemical method. Transparent conductive films were produced using the UL-GO sheets that were deposite...Monolayer ultra-large graphene oxide （UL-GO） sheets with diameter up to about 100 μm were synthesized based on a chemical method. Transparent conductive films were produced using the UL-GO sheets that were deposited layer-by-layer on a substrate by the Langmuir-Blodgett （L-B） assembly technique. The films produced from UL-GO sheets with a close-packed flat structure exhibit exceptionally high electrical conductivity and transparency after thermal reduction. A remarkable sheet resistance of 605 -/sq at 86% transparency is obtained, which outperforms the graphene films grown on a Ni substrate by chemical vapor deposition. The technique used to produce transparent conductive films is facile, inexpensive and tunable for mass production.展开更多
The presence of oxygen functional groups is detrimental to the capacitive performance of porous carbon electrode in organic electrolyte. In this regards, hydrogen thermal reduction has been demonstrated effective appr...The presence of oxygen functional groups is detrimental to the capacitive performance of porous carbon electrode in organic electrolyte. In this regards, hydrogen thermal reduction has been demonstrated effective approach in removing the unstable surface oxygen while maintaining the high porosity of carbon matrix. However, the exact evolution mechanism of various oxygen species during this process, as well as the correlation with electrochemical properties, is still under development. Herein, biomass-based porous carbon is adopted as the model material to trace its structure evolution of oxygen removal under hydrogen thermal reduction process with the temperature range of 400–800 °C. The optimum microstructure with low oxygen content of 0.90% and proper pore size distribution was achieved at 700°C. XPS, TPRMS and Boehm titration results indicate that the oxygen elimination undergoes three distinctive stages(intermolecular dehydration, hydrogenation and decomposition reactions). The optimum microstructure with low oxygen content of 0.90% and proper pore size distribution was achieved at 700 °C. Benefiting from the stable electrochemical interface and the optimized porous structure, the as-obtained HAC-700 exhibit significantly suppressed self-discharge and leak current, with improved cycling stability, which is attributable to the stabilization of electrochemical interface between carbon surface and electrolyte. The result provides insights for rational design of surface chemistry for high-performance carbon electrode towards advanced energy storage.展开更多
The formation and qualification of redox sites in transition metal oxides are always the active fields related to electronics, catalysis, sensors, and energy-storage units. In the present study, the temperature depend...The formation and qualification of redox sites in transition metal oxides are always the active fields related to electronics, catalysis, sensors, and energy-storage units. In the present study, the temperature dependence of thermal reduction of MoO3 was surveyed at the range of 350℃ to 750℃. Upon reduction, the formed redox species characterized by EPR spectroscopy are the MoVion and superoxide anion radical (O2-) when the reduction was induced at the optimal temperature of 300-350℃. When heating-up from 350℃, the EPR signals started to decline in amplitude. The signals in the range of 400-450℃ decreased to half of that at 350℃, and then to zero at ~600℃. Further treatment at even higher temperature or prolonged heating time at 500℃ caused more reduction and more free electrons were released to the MoO3 bulk, which results in a delocalized means similar to the antiferromagnetic coupling. These data herein are helpful to prepare and study the metal-oxide catalysts.展开更多
Temperature-re s ponsive resistance transition behaviors of the melamine sponges wrapped with different graphene oxide derivatives(i.e.nanoribbon,wide-ribbon and sheet)were investigated.Melamine sponge composites coat...Temperature-re s ponsive resistance transition behaviors of the melamine sponges wrapped with different graphene oxide derivatives(i.e.nanoribbon,wide-ribbon and sheet)were investigated.Melamine sponge composites coated by three types of GO derivatives were prepared by a simple dip-coating approach.All these composites show good mechanical flexibility and reliability(almost unchanged compressive stress at 70%strain after 100 cycles),high hydrophobicity(water contact angle>120°),excellent flame resistance(self-extinguishing)and structural stability even after burning,which was used to construct the resistance-based fire alarm/warning sensor.Notably,the different resistance response behaviors of such sensors are strongly dependent on the GO size and network formed on the MF skeleton surface.Typically,at a fixed high temperature of~350℃,the three fire alarm sensors show different response time(to trigger the alarm light)of 6.3,8.4 and 11.1 s for nanoribbon,wide-ribbon and sheet at the same concentration,respectively.The structural observation and chemical analysis demonstrated that the discrepancy of temperature-responsive resistance transition behaviors of various GO derivatives was strongly determined by their different thermal reduction degrees during the high-tempe rature or flame treating process.This work offers a design and development for construction of smart fire alarm device for potential fire prevention and safety applications.展开更多
Graphene oxide(GO)with excellent dispersion ability can assist the dispersion of single-walled carbon nanotube(SWCNT)and promote the formation of uniform and stable GO/SWCNT coating liquid.The highly conductive polyet...Graphene oxide(GO)with excellent dispersion ability can assist the dispersion of single-walled carbon nanotube(SWCNT)and promote the formation of uniform and stable GO/SWCNT coating liquid.The highly conductive polyethylene terephthalate/reduced graphene oxide/SWCNT(PET/rGO/SWCNT)electromagnetic shielding composite fabric was successfully prepared by anchoring rGO/SWCNT on PET fabric via dip-coating piror to low-temperature thermal reduction.The results showed that the carboxyl groups and hydroxyl groups formed of hydrophilic-treated PET were conducive to the formation of hydrogen bonds with that of GO,which enhanced the interaction between PET fabric and GO/SWCNT coating;the loading of GO/SWCNT increased with the number of dip-coating,the unit area loading of rGO/SWCNT in the final composite fabric was 2.7 mg/cm^(2) after 10 dip-coating cycles and thermal reduction;the PET/rGO/SWCNT composite fabric had a continuous and dense conductive network,with a conductivity of up to 41.6 S/m and the average electromagnetic interference shielding effectiveness in X-band was 22 dB;the flexible PET/rGO/SWCNT composite fabric was not only easy to process,but also exhibited excellent conductivity and shielding efficiency,showing great potential in the application of electromagnetic shielding fabrics.展开更多
The recovery of iron from iron sinking slag and lead smelter slag was investigated by desulfurization-reduction bath smelting. The effects of lead smelter slag(LSS) to iron sinking slag(ISS) mass ratio and temperature...The recovery of iron from iron sinking slag and lead smelter slag was investigated by desulfurization-reduction bath smelting. The effects of lead smelter slag(LSS) to iron sinking slag(ISS) mass ratio and temperature were investigated in desulfurization experiments. The X-ray diffraction(XRD) and X-ray fluorescence(XRF) analyses show that the optimum conditions are LSS:ISS of 3:7 and temperature of 1350°C. The composition of desulfurization products is mainly Zn Fe2O4, and the desulfurization rate of 99.66% is obtained under optimum conditions. The thermogravimetric(TG) and differential scanning calorimeter(DSC) analyses demonstrate that reductant is necessary for decomposition and reduction of zinc ferrite in desulfurization product. The effects of reductant, temperature and feeding modes on iron enrichment were investigated in reduction experiments. The scanning electron microscope(SEM) and energy dispersive spectrometer(EDS) determination show that the iron content of reduction product is up to 99.36% under optimum conditions of coke as reductant, reduction temperature of 1450°C and the feeding mode of premixing.展开更多
Herein, we attempted to engineer oxygen vacancies on the surface of LaCoO_(3) perovskite through simple post-treatments(acid or reductive thermal treatments). Acid treatment induces oxygen vacancies through the select...Herein, we attempted to engineer oxygen vacancies on the surface of LaCoO_(3) perovskite through simple post-treatments(acid or reductive thermal treatments). Acid treatment induces oxygen vacancies through the selective etching of the La cations, whereas thermal treatment in a reducing atmosphere generates oxygen vacancies by directly removing lattice oxygen. The characterization results confirm that the number of surface oxygen vacancies, which are crucial in various catalytic oxidation reactions,considerably increases in the LaCoO_(3) catalysts treated with acid or reducing gas. Acid treatment enriches the oxygen vacancies while maintaining the structure of the LaCoO_(3) catalysts, which can not be achieved through reductive thermal treatment. Therefore, the acid treatment is considered a promising technique for oxygen vacancy engineering of perovskite catalysts for tuning their catalytic activities. Furthermore,the catalytic activities of the posttreated LaCoO_(3) catalysts for CO oxidation were evaluated and are noted to be considerably better than those of the pristine LaCoO_(3) catalyst due to their abundant oxygen vacancies. Consequently, we conclude that the oxygen vacancies of perovskite catalysts can be effectively engineered via two simple methods and play a significant role in CO oxidation.展开更多
The theoretical energy consumption(TEC)analytical methods and the calculated models for the electrolytic and thermal reduction metal separation processes have been put forward based on thermodynamics and physical chem...The theoretical energy consumption(TEC)analytical methods and the calculated models for the electrolytic and thermal reduction metal separation processes have been put forward based on thermodynamics and physical chemistry principles,providing theoretical foundation for choosing the optimum metal separation methods.Based on the models,the TECs of the Mg separation processes are taken as an example,and have been calculated and analyzed contrastively,including the MgCl_2 electrolytic method,the MgO electrolytic method with inert electrode and with carbon anode,and the silicothermic method.It is shown that the thermal method is more reasonable than the electrolytic methods to separate Mg under low efficiency of coal power generation.展开更多
Ruthenium(Ru)is a promising electrocatalyst for hydrogen oxidation reaction(HOR)due to the similar metal hydrogen bond energy to Pt.However,Ru is easily deactivated or dissolved under an oxidation potential,which make...Ruthenium(Ru)is a promising electrocatalyst for hydrogen oxidation reaction(HOR)due to the similar metal hydrogen bond energy to Pt.However,Ru is easily deactivated or dissolved under an oxidation potential,which makes it unavailable in proton exchange membrane fuel cells.In this work,ultrastable Ru-based electrocatalysts for HOR in high-temperature polymer electrolyte membrane fuel cells(HTPEMFCs)were developed by Mo doping.Under the operation conditions of HT-PEMFCs,thermal reduction inhibited the production of amorphous Ru oxide(RuO_(2))in the Ru-based electrocatalysts during the HOR.Mo doping significantly improved the stability of the electrocatalyst by decreasing the reduction temperature of RuO_(2)and accelerating the HOR by reducing the adsorption of H*.RuMo/C exhibited excellent HOR activity at high temperatures due to thermal reduction inhibition of electrooxidation;the fabricated HT-PEMFCs exhibited long-term stability and a 1050 mW cm^(−2)peak power density,comparable to the commercial Pt catalyst.This work provides a novel strategy for designing electrocatalysts by combining material intrinsic properties and work conditions,which could promote the development of advanced electrocatalysts for HT-PEMFCs.展开更多
基金the financial support provided by the National Key R&D Program of China(Grant No.2023YFC3903900)the Science and Technology Innovation Talent Program of Hubei Province(Grant No.2022EJD002)+1 种基金the Sichuan Science and Technology Program(Grant No.2025ZNSFSC0378)the Key Laboratory of Green Chemistry of Sichuan Institutes of Higher Education(Grant No.LZJ2303).
文摘Specialized vanadium(V)-iron(Fe)-based alloy additives utilized in the production of V-containing steels were investigated.Vanadium slag from the Panzhihua region of China was utilized as a raw material to optimize process parameters for the preparation of V-Fe-based alloy via silicon thermal reduction.Experiments were conducted to investigate the effects of reduction temperature,holding time,and slag composition on alloy-slag separation,alloy microstructure,and the oxide content of residual slag,with an emphasis on the recovery of valuable metal elements.The results indicated that the optimal process conditions for silicon thermal reduction were achieved at reduction temperature of 1823 K,holding time of 240 min,and slag composition of 45 wt.%SiO_(2),40 wt.%CaO,and 15 wt.%Al_(2)O_(3).The resulting V-Fe-based alloy predominantly consisted of Fe-based phases such as Fe,titanium(Ti),silicon(Si)and manganese(Mn),with Si,V,as well as chromium(Cr)concentrated in the intercrystalline phase of the Fe-based alloy.The recoveries of Fe,Mn,Cr,V,and Ti under the optimal conditions were 96.30%,91.96%,86.53%,80.29%,and 74.82%,respectively.The key components of the V-Fe-based alloy obtained were 41.96 wt.%Si,27.55 wt.%Fe,12.13 wt.%Mn,5.53 wt.%V,4.86 wt.%Cr,and 3.74 wt.%Ti,thereby enabling the comprehensive recovery of the valuable metal from vanadium slag.
基金Project supported by the National Key Basic Research Program of China (Grant Nos.2012CB626800 and 2010CB934700)the National Natural Science Foundation of China (Grant Nos.51073115,51003072,51173127,and 51273144)
文摘Transparent conductive graphene films are fabricated by the transfer printing of graphene aqueous dispersion followed by hydrohalic acids and thermal reduction. Results indicate that the graphene film reduced by hydroiodic acid （HI） reduction combined with thermal treatment shows a higher electrical conductivity than that reduced only by thermal treatment at the same transparency. A film with a sheet resistance of - 2400 D./sq at a transparency over 72% is obtained at a typical wavelength of 550 nm.
文摘Up to now, the Pedgion magnesium reduction process is the dominating magnesium production process. In 2004, about 98% of raw magnesium is produced by Pedgion magnesium reduction process in China which equals to 60% of the global output. It shows that the dolomite-ferrosilicon thermal reduction process is the most important method to produce magnesium in the world. Limited by the disadvantage of dolomite-ferrosilicon thermal reduction process, the magnesium producing process always followed by relatively severe pollution, while the resource utilizing efficiency keeps very low. With the rapid development of dolomite-ferrosilicon thermal reduction process in China, many research works have been done aiming at the process technology and the reduction theory, and the magnesium producing process has got great evolution. The history of dolomite-ferrosilicon thermal reduction process was introduced; the process character, the merits and which defects were also discussed. Defects in dolomite-ferrosilicon thermal reduction process were expatiated, and feasible method and idea to upgrade the process was put forward. The main problems and the potential troubles hindering the development of magnesium industry were analyzed. Finally, the probability to further improve the thermal reduction process and the effective approaches to develop Chinese magnesium industry were discussed.
基金the National Natural Science Foundation of China(No.50474038,50674048)
文摘The organic gel-thermal reduction process was successfully used for the preparation of magnetic metal Ni, Fe, Fe-Ni fine fibers from raw materials of citric acid or lactic acid and metal salts. Ni, Fe and Fe-Ni fine fibers synthesized were featured with diameters of around 1 μm and lengths of as long as 2 m for Ni fibers, 0.5 m for iron fibers, 1 m for Fe-Ni fibers. The structure, thermal decomposition process and morphologies of the gel precursors and fibers derived from thermal reduction of these gel precursors were characterized by FTIR, XRD,TG/DSC and SEM, respectively. The gel spinnability largely depends on molecular structures of metal-carboxylate complexes formed in the gel. It is reasoned that these gels consist of linear-type structural molecules [（C6H6O7）Ni]n or [（C6H5O7）2Ni3] for the nickel citrate gel, [（C3H5O3）3Fe] for the ferric lactate gel, [（C6H5O7）5（NiFe）3] for the iron-nickel citrate gel respectively and the gels obtain showed a good spinning performance.
基金Projects(50474038 50674048) supported by the National Natural Science Foundation of China
文摘The organic gel-thermal reduction process was used for the preparation of ferromagnetic metal Ni, Co and Fe fine fibers from the raw materials of citric acid, lactic acid and metal salts. The structure, thermal decomposition process and morphologies of the gel precursors and fibers derived from thermal reduction of these gel precursors were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, thermo-gravimetric/differential scanning calorimetry and scanning electron microscopy. The results show that spinnability of gel largely depends on molecular structure of metal-carboxylate complex that is a linear-type structure formed in the gel. As a result, the gels exhibit a good spinnability. Metal Ni, Co and Fe fine fibers are featured with diameters of around 1 μm and a high aspect ratio up to 1×106.
基金supported by the National Natural Science Foundation of China(Nos.51662002,51762002,and 52104358)Graduate Student Innovation Program(No.YCX22138)the Key Research and Development Program of Ningxia,China(No.2019BFH02021)。
文摘High-entropy nitride powders are one of prerequisite materials for the preparation of high-performance high-entropy nitride ceramics.In this paper,high-entropy(HfZrTiNbTa)N powders were synthesized via nitride(i.e.,silicon nitride(Si_(3)N_(4)))thermal reduction with soft mechanochemical assistance.The results show that metal oxides like hafnium dioxide(HfO_(2)),zirconium dioxide(ZrO_(2)),titanium dioxide(TiO_(2)),niobium pentoxide(Nb_(2)O_(5)),and tantalum pentoxide(Ta_(2)O_(5))can all be transformed into the corresponding metal nitrides in the presence of Si_(3)N_(4)at 1700℃,and solid solution of the metal nitrides can be formed as the temperature increases to 2100℃.The high-entropy(HfZrTiNbTa)N powders with submicron-sized particles,a narrower size distribution,and a single face-centered cubic(fcc)structure are obtained from raw material mixtures ground for 10 h and subsequently sintered at 1800℃.In addition,the high-entropy bulk nitride ceramics with relative density(Rw)of 94.31%±0.76%,Vickers hardness of 21.00±0.94 GPa,and fracture toughness(KIC)of 3.18±0.16 MPa·m1/2 are obtained with submicron-sized powders,which are superior to those obtained with micron-sized powders.
基金the financial support provided by the independent subject of State Key Laboratory of Advanced MetallurgyUniversity of Science and Technology Beijing,China,grant number 41617003,which enabled the successful completion of the study.
文摘Final electromagnetic stirring(F-EMS)and thermal soft reduction(TSR)are techniques that improve the inner quality of continuous casting billets,but they have rarely been applied simultaneously.The application effects of F-EMS and TSR were compared,and a process integrating F-EMS and TSR was adopted for a billet continuous caster.A heat transfer model was established to calculate the thermal behavior of 82A tire cord steel billet.The locations of F-EMS and TSR were determined,followed by conducting a series of plant trials,involving F-EMS alone,TSR alone,and the integrated process of F-EMS and TSR.The results showed that F-EMS or TSR could effectively improve the inner quality of the billet under their respective suitable working conditions.Moreover,F-EMS was found to be more helpful in terms of improving central segregation,while TSR tended to improve V-segregation,central porosity,and pipe.The integration of F-EMS and TSR allowed the advantages of each technique to be utilized,thereby better improving the inner quality.Among all the working conditions,82A steel billet showed optimum inner quality when the current of F-EMS was 240 A and the cooling intensity of TSR was 2.2 m^(3) h^(−1).These findings demonstrate that the integration of F-EMS and TSR is promising for application on continuous casting billets.
基金financially supported by the Industrial Research Project of Liaoning Province(No.2011221002)the Project of High Technology Plan of Magnesium Materials of Liaoning(No.MYF2011-34)
文摘A new process of producing magnesium by thermal vacuum reduction using dolomite and magnesite as materials and silicocalcium as reductant was studied in this study. The reduction process of MgO by silicocalcium was analyzed by phases analysis of reduction slag through X-ray diffraction （XRD） and the factors influencing the reduction ratio of MgO were investigated. The experi- mental results show that when using silicocalcium as reductant, the reduction ratio of MgO can be over 93 %. In the reduction process, calcium in silicocalcium takes part in the reduction reaction of MgO firstly below 1,000 ℃ and it makes CaSi2 decompose. It also releases elemental silicon which has more reactive activity and improves the reduction reaction of MgO. That is the main cause that the reduction ratio of MgO using silicocalcium as reductant is 8 %-10 % higher than that by Pidgeon process using fer- rosilicon as reductant under the same conditions.
基金financial support from the Yunnan Province Key Industries Science and Technology Special Project for Colleges and UniversitiesChina(No.FWCY-QYCT2024006)+6 种基金National Natural Science Foundation of China(Nos.52104351 and 52364051)Science and Technology Major Project of Yunnan Province,China(No.202202AG050007)the Yunnan Fundamental Research ProjectsChina(No.202401AT070314)the Key Technology Research and Development Program of Shandong Province,China(No.2023CXGC010903)Central Guidance Local Scientific and Technological Development Funds,China(No.202407AB110022)Yunnan Province Xingdian Talent Support Plan Project,China。
文摘Titanium exhibits outstanding properties,particularly,high specific strength and resistance to both high and low temperatures,earning it a reputation as the metal of the future.However,because of the highly reactive nature of titanium,metallic titanium production involves extensive procedures and high costs.Considering its advantages and limitations,the European Union has classified titanium metal as a critical raw material(CRM)of low category.The Kroll process is predominantly used to produce titanium;however,molten salt electrolysis(MSE)is currently being explored for producing metallic titanium at a low cost.Since 2000,electrolytic titanium production has undergone a wave of technological advancements.However,because of the intermediate and disproportionation reactions in the electrolytic titanium production process,the process efficiency and titanium purity according to industrial standards could not be achieved.Consequently,metallic titanium production has gradually diversified into employing technologies such as thermal reduction,MSE,and titanium alloy preparation.This study provides a comprehensive review of research advances in titanium metal preparation technologies over the past two decades,highlighting the challenges faced by the existing methods and proposing potential solutions.It offers useful insights into the development of low-cost titanium preparation technologies.
文摘The kinetics of isothermal reduction of Ag2O with graphite under argon atmosphere for a non-activated sample and mechanically activated sample was investigated.It is found that Johnson-Mehl-Avrami model appropriately explained the thermal and mechanochemical synthesis of Ag from Ag2O＋ghraphite mixture.The process kinetics was investigated using the same approach for milled and unmilled samples.The results show that the Avrami exponent of mechanochemical reduction is higher than that of high temperature thermal reduction.Also,the mechanisms of nuclei growth in thermal and mechanochemical reduction are diffusion controlled and interface controlled,respectively.
基金supported by the National Key R&D Program of China(Grant No.2021YFA0715803)the National Natural Science Foundation of China(Grant Nos.52293373 and 52130205)+3 种基金the Special Funds of the National Natural Science Foun-dation of China(Grant No.52342207)the National Science and Technology Major Project(Grant No.J2022-VI-0011-0042)the Joint Fund of Henan Province Science and Technology R&D Program(Grant No.225200810002)the Research Foundation of the Science and Technology on Thermostructural Composite Materials Laboratory(Grant No.JCKYS2024607001-1).
文摘Hafnium carbonitride(HfC_(x)N_(1-x))ceramics have drawn considerable interest due to their exceptional me-chanical and thermophysical properties.Herein,we report a novel single-source precursor with Hf-N bonds as the main chain and fabricate HfC_(x)N_(1-x)ceramics after pyrolysis of the precursor.The synthesis,ceramic conversion,and microstructural evolution of the single-source precursor as well as the derived HfC_(x)N_(1-x)ceramics treated under various atmospheres were investigated.The results indicate that in an argon atmosphere,the nitrogen content within HfC_(x)N_(1-x)decreases with rising temperature.While under a nitrogen atmosphere,the high concentration of N_(2)facilitates the rapid conversion of HfO2 to Hf7O8N4,which subsequently promotes the transformation of the HfC_(x)N_(1-x)solid solution ceramics.During this process,there is also an inhibitory effect of N_(2)on the tendency of HfN into HfC.Moreover,the desired chemical composition of HfC_(x)N_(1-x)can be regulated by adjusting the N_(2)concentration in the heat treat-ment atmosphere.The present work proposes a novel strategy for the single-source precursor-derived carbonitride ceramics and provides a deep understanding of the preparation and property modulation of HfC_(x)N_(1-x)ceramics.
基金Project (51102170) supported by the National Natural Science Foundation of ChinaProject (2010CB234609) supported by the National Basic Research Program of China
文摘Monolayer ultra-large graphene oxide （UL-GO） sheets with diameter up to about 100 μm were synthesized based on a chemical method. Transparent conductive films were produced using the UL-GO sheets that were deposited layer-by-layer on a substrate by the Langmuir-Blodgett （L-B） assembly technique. The films produced from UL-GO sheets with a close-packed flat structure exhibit exceptionally high electrical conductivity and transparency after thermal reduction. A remarkable sheet resistance of 605 -/sq at 86% transparency is obtained, which outperforms the graphene films grown on a Ni substrate by chemical vapor deposition. The technique used to produce transparent conductive films is facile, inexpensive and tunable for mass production.
基金National Science Foundation for Excellent Young Scholars of China (21922815)Key Research and Development (R&D) Projects of Shanxi Province (201903D121007)+3 种基金Natural Science Foundations of Shanxi Province (201801D221156)DNL Cooperation Fund of CAS (DNL180308)Science and Technology Service Network Initiative of CAS (KFJ-STS-ZDTP-068)Youth Innovation Promotion Association of CAS。
文摘The presence of oxygen functional groups is detrimental to the capacitive performance of porous carbon electrode in organic electrolyte. In this regards, hydrogen thermal reduction has been demonstrated effective approach in removing the unstable surface oxygen while maintaining the high porosity of carbon matrix. However, the exact evolution mechanism of various oxygen species during this process, as well as the correlation with electrochemical properties, is still under development. Herein, biomass-based porous carbon is adopted as the model material to trace its structure evolution of oxygen removal under hydrogen thermal reduction process with the temperature range of 400–800 °C. The optimum microstructure with low oxygen content of 0.90% and proper pore size distribution was achieved at 700°C. XPS, TPRMS and Boehm titration results indicate that the oxygen elimination undergoes three distinctive stages(intermolecular dehydration, hydrogenation and decomposition reactions). The optimum microstructure with low oxygen content of 0.90% and proper pore size distribution was achieved at 700 °C. Benefiting from the stable electrochemical interface and the optimized porous structure, the as-obtained HAC-700 exhibit significantly suppressed self-discharge and leak current, with improved cycling stability, which is attributable to the stabilization of electrochemical interface between carbon surface and electrolyte. The result provides insights for rational design of surface chemistry for high-performance carbon electrode towards advanced energy storage.
基金supported by the National Key R&D Program of China(No.2018YFA0306600)AnHui Initiative in Quantum Information Technologies(No.AHY050000)
文摘The formation and qualification of redox sites in transition metal oxides are always the active fields related to electronics, catalysis, sensors, and energy-storage units. In the present study, the temperature dependence of thermal reduction of MoO3 was surveyed at the range of 350℃ to 750℃. Upon reduction, the formed redox species characterized by EPR spectroscopy are the MoVion and superoxide anion radical (O2-) when the reduction was induced at the optimal temperature of 300-350℃. When heating-up from 350℃, the EPR signals started to decline in amplitude. The signals in the range of 400-450℃ decreased to half of that at 350℃, and then to zero at ~600℃. Further treatment at even higher temperature or prolonged heating time at 500℃ caused more reduction and more free electrons were released to the MoO3 bulk, which results in a delocalized means similar to the antiferromagnetic coupling. These data herein are helpful to prepare and study the metal-oxide catalysts.
基金the funding support from the Natural Science Foundation of China(Nos.51973047 and 12002112)the Natural Science Foundation of Zhejiang Province(Nos.LY18E030005 and LY15E030015)+1 种基金the Science and Technology Project of Zhejiang Province(No.LGG20B040002)the Science and Technology Program of Hangzhou(Nos.20191203B16 and 20180533B01)。
文摘Temperature-re s ponsive resistance transition behaviors of the melamine sponges wrapped with different graphene oxide derivatives(i.e.nanoribbon,wide-ribbon and sheet)were investigated.Melamine sponge composites coated by three types of GO derivatives were prepared by a simple dip-coating approach.All these composites show good mechanical flexibility and reliability(almost unchanged compressive stress at 70%strain after 100 cycles),high hydrophobicity(water contact angle>120°),excellent flame resistance(self-extinguishing)and structural stability even after burning,which was used to construct the resistance-based fire alarm/warning sensor.Notably,the different resistance response behaviors of such sensors are strongly dependent on the GO size and network formed on the MF skeleton surface.Typically,at a fixed high temperature of~350℃,the three fire alarm sensors show different response time(to trigger the alarm light)of 6.3,8.4 and 11.1 s for nanoribbon,wide-ribbon and sheet at the same concentration,respectively.The structural observation and chemical analysis demonstrated that the discrepancy of temperature-responsive resistance transition behaviors of various GO derivatives was strongly determined by their different thermal reduction degrees during the high-tempe rature or flame treating process.This work offers a design and development for construction of smart fire alarm device for potential fire prevention and safety applications.
文摘Graphene oxide(GO)with excellent dispersion ability can assist the dispersion of single-walled carbon nanotube(SWCNT)and promote the formation of uniform and stable GO/SWCNT coating liquid.The highly conductive polyethylene terephthalate/reduced graphene oxide/SWCNT(PET/rGO/SWCNT)electromagnetic shielding composite fabric was successfully prepared by anchoring rGO/SWCNT on PET fabric via dip-coating piror to low-temperature thermal reduction.The results showed that the carboxyl groups and hydroxyl groups formed of hydrophilic-treated PET were conducive to the formation of hydrogen bonds with that of GO,which enhanced the interaction between PET fabric and GO/SWCNT coating;the loading of GO/SWCNT increased with the number of dip-coating,the unit area loading of rGO/SWCNT in the final composite fabric was 2.7 mg/cm^(2) after 10 dip-coating cycles and thermal reduction;the PET/rGO/SWCNT composite fabric had a continuous and dense conductive network,with a conductivity of up to 41.6 S/m and the average electromagnetic interference shielding effectiveness in X-band was 22 dB;the flexible PET/rGO/SWCNT composite fabric was not only easy to process,but also exhibited excellent conductivity and shielding efficiency,showing great potential in the application of electromagnetic shielding fabrics.
基金Project(2011AA061003)supported by the National High Technology Research and Development Program of China
文摘The recovery of iron from iron sinking slag and lead smelter slag was investigated by desulfurization-reduction bath smelting. The effects of lead smelter slag(LSS) to iron sinking slag(ISS) mass ratio and temperature were investigated in desulfurization experiments. The X-ray diffraction(XRD) and X-ray fluorescence(XRF) analyses show that the optimum conditions are LSS:ISS of 3:7 and temperature of 1350°C. The composition of desulfurization products is mainly Zn Fe2O4, and the desulfurization rate of 99.66% is obtained under optimum conditions. The thermogravimetric(TG) and differential scanning calorimeter(DSC) analyses demonstrate that reductant is necessary for decomposition and reduction of zinc ferrite in desulfurization product. The effects of reductant, temperature and feeding modes on iron enrichment were investigated in reduction experiments. The scanning electron microscope(SEM) and energy dispersive spectrometer(EDS) determination show that the iron content of reduction product is up to 99.36% under optimum conditions of coke as reductant, reduction temperature of 1450°C and the feeding mode of premixing.
基金Project supported by the Korea Institute of Energy Technology Evaluation and Planning(KETEP)the Ministry of Trade,Industry&Energy(MOTIE),Republic of Korea(No.20214810100010)。
文摘Herein, we attempted to engineer oxygen vacancies on the surface of LaCoO_(3) perovskite through simple post-treatments(acid or reductive thermal treatments). Acid treatment induces oxygen vacancies through the selective etching of the La cations, whereas thermal treatment in a reducing atmosphere generates oxygen vacancies by directly removing lattice oxygen. The characterization results confirm that the number of surface oxygen vacancies, which are crucial in various catalytic oxidation reactions,considerably increases in the LaCoO_(3) catalysts treated with acid or reducing gas. Acid treatment enriches the oxygen vacancies while maintaining the structure of the LaCoO_(3) catalysts, which can not be achieved through reductive thermal treatment. Therefore, the acid treatment is considered a promising technique for oxygen vacancy engineering of perovskite catalysts for tuning their catalytic activities. Furthermore,the catalytic activities of the posttreated LaCoO_(3) catalysts for CO oxidation were evaluated and are noted to be considerably better than those of the pristine LaCoO_(3) catalyst due to their abundant oxygen vacancies. Consequently, we conclude that the oxygen vacancies of perovskite catalysts can be effectively engineered via two simple methods and play a significant role in CO oxidation.
文摘The theoretical energy consumption(TEC)analytical methods and the calculated models for the electrolytic and thermal reduction metal separation processes have been put forward based on thermodynamics and physical chemistry principles,providing theoretical foundation for choosing the optimum metal separation methods.Based on the models,the TECs of the Mg separation processes are taken as an example,and have been calculated and analyzed contrastively,including the MgCl_2 electrolytic method,the MgO electrolytic method with inert electrode and with carbon anode,and the silicothermic method.It is shown that the thermal method is more reasonable than the electrolytic methods to separate Mg under low efficiency of coal power generation.
基金The Top ten Technological Breakthrough Projects in Hunan Province(grant no.2023GK1050),the National Key R&D Program of China(grant no.2021YFA1500900)the National Natural Science Foundation of China(NSFC+9 种基金grant nos.22102053,21825201,22172047,and U19A2017)the Provincial Natural Science Foundation of Hunan,China(grant nos.2024JJ2012,2019GK2031,2016TP1009,2020JJ5045,and 2021JJ30089)the Science and Technology Innovation Program of Hunan Province,China(grant nos.2020RC2020 and 2022RC1036)Shenzhen Science and Technology Program,China(grant no.JCYJ20210324122209025)Changsha Municipal Natural Science Foundation,China(grant no.kq2007009)Changsha Municipal Natural Science Foundation,China(grant no.kq2007009)Basic and Applied Basic Research Foundation of Guangdong Province-Regional joint fund project,China(grant no.2021B1515120024)Guangdong Basic and Applied Basic Research Foundation,China(grant no.2024A1515012889)Shenzhen Science and Technology Program,China(grant no.JCYJ20210324122209025)Major Program of the Natural Science Foundation of Hunan Province,China(grant no.2021JC0006).
文摘Ruthenium(Ru)is a promising electrocatalyst for hydrogen oxidation reaction(HOR)due to the similar metal hydrogen bond energy to Pt.However,Ru is easily deactivated or dissolved under an oxidation potential,which makes it unavailable in proton exchange membrane fuel cells.In this work,ultrastable Ru-based electrocatalysts for HOR in high-temperature polymer electrolyte membrane fuel cells(HTPEMFCs)were developed by Mo doping.Under the operation conditions of HT-PEMFCs,thermal reduction inhibited the production of amorphous Ru oxide(RuO_(2))in the Ru-based electrocatalysts during the HOR.Mo doping significantly improved the stability of the electrocatalyst by decreasing the reduction temperature of RuO_(2)and accelerating the HOR by reducing the adsorption of H*.RuMo/C exhibited excellent HOR activity at high temperatures due to thermal reduction inhibition of electrooxidation;the fabricated HT-PEMFCs exhibited long-term stability and a 1050 mW cm^(−2)peak power density,comparable to the commercial Pt catalyst.This work provides a novel strategy for designing electrocatalysts by combining material intrinsic properties and work conditions,which could promote the development of advanced electrocatalysts for HT-PEMFCs.
