The composites were prepared by ball-milling ZrO_2(3%Y_2O_3) and γ-Al_2O_3 nanoparticles, pressing unidirectionally, cold-pressing isostatically and pressurelessly sintering in air. The phases of ZrO_2 in composites ...The composites were prepared by ball-milling ZrO_2(3%Y_2O_3) and γ-Al_2O_3 nanoparticles, pressing unidirectionally, cold-pressing isostatically and pressurelessly sintering in air. The phases of ZrO_2 in composites were examined by X-ray diffraction. The microstructure of Al_2O_3/3Y-TZP composites was observed by scanning electron microscope (SEM) and transmission electron microscopy (TEM) respectively. The X-ray analysis reveals that ZrO_2 of both surface and fracture surface is mainly t-ZrO_2. The SEM image shows that there are some intragranular particles in large granulars. The fracture toughness K_ 1c of Al_2O_3/70%ZrO_2(3%Y_2O_3(mole fraction)) composite tested by single-edge notched bending is 13.5 MPa·m 1/2. Being toughened by the ferroelastic domain switching and the intragranular microstructure explains high toughness of the composite.展开更多
As one of the most important ways to reduce the greenhouse gas emission,carbon dioxide（CO2）enhanced gas recovery（CO2-EGR） is attractive since the gas recovery can be enhanced simultaneously with CO2sequestration.B...As one of the most important ways to reduce the greenhouse gas emission,carbon dioxide（CO2）enhanced gas recovery（CO2-EGR） is attractive since the gas recovery can be enhanced simultaneously with CO2sequestration.Based on the existing equation of state（EOS） module of TOUGH2 MP,extEOS7C is developed to calculate the phase partition of H2O-CO2-CH4-NaCl mixtures accurately with consideration of dissolved NaCI and brine properties at high pressure and temperature conditions.Verifications show that it can be applied up to the pressure of 100 MPa and temperature of 150℃.The module was implemented in the linked simulator TOUGH2MP-FLAC3 D for the coupled hydro-mechanical simulations.A simplified three-dimensional（3D）1/4 model（2.2 km×1 km×1 km） which consists of the whole reservoir,caprock and baserock was generated based on the geological conditions of a gas field in the North German Basin.The simulation results show that,under an injection rate of 200,000 t/yr and production rate of 200,000 sm3/d,CO2breakthrough occurred in the case with the initial reservoir pressure of 5 MPa but did not occur in the case of 42 MPa.Under low pressure conditions,the pressure driven horizontal transport is the dominant process;while under high pressure conditions,the density driven vertical flow is dominant.Under the considered conditions,the CO2-EGR caused only small pressure changes.The largest pore pressure increase（2 MPa） and uplift（7 mm） occurred at the caprock bottom induced by only CO2injection.The caprock had still the primary stress state and its integrity was not affected.The formation water salinity and temperature variations of ±20℃ had small influences on the CO2-EGR process.In order to slow down the breakthrough,it is suggested that CO2-EGR should be carried out before the reservoir pressure drops below the critical pressure of CO2.展开更多
The influence of Er_2 O_3 addition on the phase evolution and mechanical properties of sintered(1600 ℃,4 h) ZTA(yttria stabilized zirconia toughened alumina)-TiO_2 composites was investigated. The SEM and XRD results...The influence of Er_2 O_3 addition on the phase evolution and mechanical properties of sintered(1600 ℃,4 h) ZTA(yttria stabilized zirconia toughened alumina)-TiO_2 composites was investigated. The SEM and XRD results reveal the formation of a new erbium zirconium oxide,Zr_3 Er_4 O_(12),with a granulate morphology when Er_2 O_3 content is higher than 1 wt%. The grain sizes of both Al_2 O_3 and yttria-stabilized zirconia phases decrease with an increase in the Er_2 O_3 content. The relative density, Vickers hardness and fracture toughness of the composites are found to be strongly dependent on their grain sizes, relative densities and the formation of the Zr_3 Er_4 O_(12) secondary phases. The composite with 5 wt% Er_2 O_3 shows the highest relative density(99.93%), Vickers hardness(1752 HV) and fracture toughness(7.92 MPa·m^(1/2)).展开更多
Creep and stress relaxation behavior, the elastic modulus and fracture toughness of machinable Ti3SiC2 at various temperatures from 20 to 1250℃ were investigated by means of three-point bending tests. The experiments...Creep and stress relaxation behavior, the elastic modulus and fracture toughness of machinable Ti3SiC2 at various temperatures from 20 to 1250℃ were investigated by means of three-point bending tests. The experiments were performed respectively at: (i) fixed stress and changed temperatures, and (ii) fixed temperature and changed stresses. A creep resistance parameter that represents the probability of creep deformation in a given condition was defined as a function of both applied stress and the threshold stress, varying in a range from 0 to 1. Elastic modulus at high temperatures was measured through comparing relative slopes of loading curves in cyclic loading curve. The fracture toughness measured by SENB method showed a stable value in the range of 25-1000℃, but over 1000℃, it declined abruptly from -6.7MPa·m1/2 to -2.0MPa·m1/2 at 1200℃.展开更多
文摘The composites were prepared by ball-milling ZrO_2(3%Y_2O_3) and γ-Al_2O_3 nanoparticles, pressing unidirectionally, cold-pressing isostatically and pressurelessly sintering in air. The phases of ZrO_2 in composites were examined by X-ray diffraction. The microstructure of Al_2O_3/3Y-TZP composites was observed by scanning electron microscope (SEM) and transmission electron microscopy (TEM) respectively. The X-ray analysis reveals that ZrO_2 of both surface and fracture surface is mainly t-ZrO_2. The SEM image shows that there are some intragranular particles in large granulars. The fracture toughness K_ 1c of Al_2O_3/70%ZrO_2(3%Y_2O_3(mole fraction)) composite tested by single-edge notched bending is 13.5 MPa·m 1/2. Being toughened by the ferroelastic domain switching and the intragranular microstructure explains high toughness of the composite.
基金funded by the National Natural Science Foundation of China(Grant No.NSFC51374147)the German Society for Petroleum and Coal Science and Technology(Grant No.DGMK680-4)
文摘As one of the most important ways to reduce the greenhouse gas emission,carbon dioxide（CO2）enhanced gas recovery（CO2-EGR） is attractive since the gas recovery can be enhanced simultaneously with CO2sequestration.Based on the existing equation of state（EOS） module of TOUGH2 MP,extEOS7C is developed to calculate the phase partition of H2O-CO2-CH4-NaCl mixtures accurately with consideration of dissolved NaCI and brine properties at high pressure and temperature conditions.Verifications show that it can be applied up to the pressure of 100 MPa and temperature of 150℃.The module was implemented in the linked simulator TOUGH2MP-FLAC3 D for the coupled hydro-mechanical simulations.A simplified three-dimensional（3D）1/4 model（2.2 km×1 km×1 km） which consists of the whole reservoir,caprock and baserock was generated based on the geological conditions of a gas field in the North German Basin.The simulation results show that,under an injection rate of 200,000 t/yr and production rate of 200,000 sm3/d,CO2breakthrough occurred in the case with the initial reservoir pressure of 5 MPa but did not occur in the case of 42 MPa.Under low pressure conditions,the pressure driven horizontal transport is the dominant process;while under high pressure conditions,the density driven vertical flow is dominant.Under the considered conditions,the CO2-EGR caused only small pressure changes.The largest pore pressure increase（2 MPa） and uplift（7 mm） occurred at the caprock bottom induced by only CO2injection.The caprock had still the primary stress state and its integrity was not affected.The formation water salinity and temperature variations of ±20℃ had small influences on the CO2-EGR process.In order to slow down the breakthrough,it is suggested that CO2-EGR should be carried out before the reservoir pressure drops below the critical pressure of CO2.
基金Project supported by National Natural Science Foundation of China(51571103,51501079)China Postdoctoral Science Foundation(2017M623319XB,2018T110999)Yunnan Provincial Department of Education Science Research Fund Project(2018JS033)
文摘The influence of Er_2 O_3 addition on the phase evolution and mechanical properties of sintered(1600 ℃,4 h) ZTA(yttria stabilized zirconia toughened alumina)-TiO_2 composites was investigated. The SEM and XRD results reveal the formation of a new erbium zirconium oxide,Zr_3 Er_4 O_(12),with a granulate morphology when Er_2 O_3 content is higher than 1 wt%. The grain sizes of both Al_2 O_3 and yttria-stabilized zirconia phases decrease with an increase in the Er_2 O_3 content. The relative density, Vickers hardness and fracture toughness of the composites are found to be strongly dependent on their grain sizes, relative densities and the formation of the Zr_3 Er_4 O_(12) secondary phases. The composite with 5 wt% Er_2 O_3 shows the highest relative density(99.93%), Vickers hardness(1752 HV) and fracture toughness(7.92 MPa·m^(1/2)).
文摘Creep and stress relaxation behavior, the elastic modulus and fracture toughness of machinable Ti3SiC2 at various temperatures from 20 to 1250℃ were investigated by means of three-point bending tests. The experiments were performed respectively at: (i) fixed stress and changed temperatures, and (ii) fixed temperature and changed stresses. A creep resistance parameter that represents the probability of creep deformation in a given condition was defined as a function of both applied stress and the threshold stress, varying in a range from 0 to 1. Elastic modulus at high temperatures was measured through comparing relative slopes of loading curves in cyclic loading curve. The fracture toughness measured by SENB method showed a stable value in the range of 25-1000℃, but over 1000℃, it declined abruptly from -6.7MPa·m1/2 to -2.0MPa·m1/2 at 1200℃.
