This study involved numerical simulations of a double tube heat exchanger using the ANSYS FLUENT programversion 22.The study aims to examine methods for minimizing pressure loss and consequently enhancing the thermal ...This study involved numerical simulations of a double tube heat exchanger using the ANSYS FLUENT programversion 22.The study aims to examine methods for minimizing pressure loss and consequently enhancing the thermal performance index(TPI)of a heat exchanger fitted with wavy edge tape that is a heat recovery system(the hot air in simulation instead of t heat from the exhaust gases of the brick factory furnaces and return it to warm the heavy fuel oil by substituting the electrical heater with a heat exchanger to recuperate waste heat from the flue gases,so elevating the temperature of Heavy fuel oil(HFO)to inject from the roof nozzles of combustion chamber of the furnace furthermore reducing cost(by finding the optimal design of wavy edge tape))and energy consumption.Air was selected as the hot gas in the inner pipe instead of furnace exhaust gases due to their similar thermal characteristics.A numerical analysis was conducted to create a novel wavy edge tape with varying widths(50%Di,75%Di,and 95%Di),lengths(1000,1200,1400)mm,amplitudes(5,10,15)mm,and periods of wavy length(5,10,15)mm.The flow rate of the outer pipe fluid(oil)ranges from(0.06 to 0.1)kg/s,while the velocity of the hot fluid(air)varies from(1 to 27)m/s,Re_(air)(6957 to 187,837).The entrance temperature of the hot fluid can be either(200,225,and 250)℃.The study finds that wavy edge tape tubes are more effective than smooth tubes in terms of oil outlet temperature;results revealed that an increase in the oil mass flow rate leads to a decrease in the oil outlet temperature and an increase in the heat transfer rate,at the air temperature 250℃.Additionally,the results indicate that increasing the width,length,and amplitude also leads to an increase in the oil outlet temperature of(94-94.12)℃,the pressure drop of(568.3)Pa,and the Nusselt number(65.7-66.5)respectively on the oil side.Finally,the heat exchanger’s best thermal performance index was found by investigating temperature contour at amplitude(A=5),period(p=15),width(w=75%Di),and length(L=1200 mm).The values for these parameters are,in order(1.02,1.025,1.02,and 1.0077).展开更多
The fracture behavior of superconducting tapes with central and edge oblique cracks subject to electromagnetic forces is investigated. Maxwell's equations and the critical state-Bean model are used to analytically...The fracture behavior of superconducting tapes with central and edge oblique cracks subject to electromagnetic forces is investigated. Maxwell's equations and the critical state-Bean model are used to analytically determine the magnetic flux density and electromagnetic force distributions in superconducting tapes containing central and edge oblique cracks. The distributed dislocation technique(DDT) transforms the mixed boundary value problem into a Cauchy singular integral equation, which is then solved by the Gauss-Chebyshev quadrature method to determine the stress intensity factors(SIFs).The model's accuracy is validated by comparing the calculated electromagnetic force distribution for the edge oblique crack and the SIFs for both crack types with the existing results. The findings indicate that the current and electromagnetic forces are significantly affected by the crack length and oblique angle. Specifically, for central oblique cracks, a smaller oblique angle enhances the risk of crack propagation, and a higher initial magnetization intensity poses greater danger under field cooling(FC) excitation. In contrast, for edge oblique cracks, a larger angle increases the likelihood of tape fractures. This study provides important insights into the fracture behavior and mechanical failure mechanisms of superconducting tapes with oblique cracks.展开更多
Heat transfer,friction factor and thermal enhancement factor characteristics of a double pipe heat exchanger fitted with square-cut twisted tapes（STT） and plain twisted tapes（PTT） are investigated experimentally u...Heat transfer,friction factor and thermal enhancement factor characteristics of a double pipe heat exchanger fitted with square-cut twisted tapes（STT） and plain twisted tapes（PTT） are investigated experimentally using the water as working fluid.The tapes（STT and PTT） have three twist ratios（y=2.0,4.4 and 6.0） and the Reynolds number ranges from 2000 to 12000.The experimental results reveal that heat transfer rate,friction factor and thermal enhancement factor in the tube equipped with STT are significantly higher than those fitted with PTT. The additional disturbance and secondary flow in the vicinity of the tube wall generated by STT are higher compared to that induced by the PTT is referred as the reason for better performance.Over the range considered,the Nusselt number,friction factor and thermal enhancement factor in a tube with STT are respectively,1.03 to 1.14,1.05 to 1.25 and 1.02 to 1.06 times of those in tube with PTT.An empirical correlation is also formulated to match with experimental data of Nusselt number and friction factor for STT and PTT.展开更多
This article introduces a computer numerical control （CNC）-based open hardware architecture system to realize the special functions of automated tape-laying （ATL） in a numerical control system. It associates a pro...This article introduces a computer numerical control （CNC）-based open hardware architecture system to realize the special functions of automated tape-laying （ATL） in a numerical control system. It associates a programmable multi-axis controller （PMAC） as the motion control unit with programmable numerical controllers （PCL-725, PCL-730） for on-off control. To bring about synchronized movements of the main 5-axis tape-laying head system and the 3-axis ultrasonic tape-cutting sub-system, the tracking-control method associated with time-based mode attributed to PMAC is applied in different cases. In addition, with the goal of realizing real-time tasks in the software system such as synchronizing motion control and on-off control, the real-time Win 2000 system is adopted. As a device driver for PMAC and PCL, a user graphical interface and a numerical control program interpretation module are also designed. This system is helpful to solve complicated problems in designing numerical controls for ATL such as ensuring high requirements for precise machine control and synchronization of motion control and on-off control.展开更多
Heat augmentation techniques play a vital role in the heating and cooling processes in industries,including solar collectors and many applications that utilize heat exchangers.Several studies are based on inserting fi...Heat augmentation techniques play a vital role in the heating and cooling processes in industries,including solar collectors and many applications that utilize heat exchangers.Several studies are based on inserting fillers inside the tubes to enhance heat transfer.This investigation considered the effects of twisted tapes with large holes on a tubular heat exchanger’s(HX)heat transmission,pressure drop,and thermal boosting factor.In the experimental section,counter-swirl flow generators used twisted tapes with pairs of 1.0 cm-diameter holes and changes in porosity(Rp)at 1.30%and 2.70%.In the experiments,air was utilized as a working fluid in a tube with a circular cross-section.The turbulent flow was considered,with Reynolds numbers(Re)domain from 4800 to 9500,and a boundary condition with a uniform wall heat flux was constructed.The findings expound that when the number of holes rose,the Nusselt number(Nu),the factor of friction(f),and the thermal enhancement factor(η)all increased as well.Additionally,as the friction factor increased,the Nusselt number of the tape-equipped tube was noticeably higher.Additionally,it was discovered that the friction factor was between 70%and 94%lower than the values of the tube without tape,while the(Nu)was between 87%and 97%higher than the conventional tube values.The maximum value ofηis 89%.According to the experimental results,empirical correlations for Nu,f,andηwere also generated.展开更多
Three kinds of silver-sheathed Bi(2223) oxide superconductor tapes (single-core tape, Ag-powder-added tape and multifilamentary type) were successfully prepared, namely, through the powder-in-tube method. The critical...Three kinds of silver-sheathed Bi(2223) oxide superconductor tapes (single-core tape, Ag-powder-added tape and multifilamentary type) were successfully prepared, namely, through the powder-in-tube method. The critical current density (Jc), the Jc-B characteristics, microstructures and the relation between Jc and strain of three kinds of tapes were evaluated and compared. The maximum Jc of three kinds of tapes at 77.7 K in zero magnetic field are 28700 A/cm2 for single-core tape, 20800 A/cm2 for Ag-powder-added tape, 11700 A/cm2 for multifilamentary tape. Single-core tapes exhibit high Jc values and good Jc-B characteristics.展开更多
The purpose of this paper is to demonstrate and investigate the concepts of new deployable boom systems, which consist of the BCON （braid coated bi-convex tape） boom and the SMA-BCON （braid coated bi-shape memory a...The purpose of this paper is to demonstrate and investigate the concepts of new deployable boom systems, which consist of the BCON （braid coated bi-convex tape） boom and the SMA-BCON （braid coated bi-shape memory alloy convex tape） boom. Both booms are developed for the deployable membrane structures such as solar sails, thin membrane solar array panels, deorbit mechanisms for small satellites and reflectors of space solar power satellite, etc. BCON booms can store around polygonal or cylindrical center hub, and the booms can deploy by the stepwise manner by releasing a constraint mechanism which pins the boons into two or three points for the total length. SMA-BCON booms are mainly developed for a square center body systems, and SMA is adapted on the bent po^nts of the booms where stored around each edge of the center hub. Through the deployment experiments of both booms, the stepwise deployment behavior and its tendency are obtained. The design concept of BCON boom and SMA-BCON hnnm i~ demonstrated through this study.展开更多
More and more attention is being focused on saline water utilization in irrigation due to the shortage of fresh water to agriculture in many regions. For purpose of reducing the risks of using of saline water for irri...More and more attention is being focused on saline water utilization in irrigation due to the shortage of fresh water to agriculture in many regions. For purpose of reducing the risks of using of saline water for irrigation, the mechanism of soil moisture and salinity distribution and transport should be well understood for developing optimum management strategies. In this paper, field experiments were carried out at Junggar Basin, China, to study the effects of drip irrigation water quality and drip tape arrangement on distribution of soil salinity and soil moisture. Six treatments were designed, including two drip tape arrangement modes and three irrigation water concentration levels （0.24, 4.68, and 7.42 dS m^-l）. Results showed that, soil moisture content （SMC） directly beneath the drip tape in all treatments kept a relatively high value about 18% before boll opening stage; the SMC in the narrow strip in single tape arrangement （Ms） plot was obviously lower than that in the double tapes arrangement （Md） plot, indicating that less sufficient water was supplied under the same condition of irrigation depth, but there was no significant reduction in yield. Mulching had not significant influence on salt accumulation but the drip tape arrangement, under the same condition of irrigation water depth and quality, compared with Md, Ms reduced salt accumulation in root zone and brought about relatively high cotton yield.展开更多
Automated tape placement is an important automated process used for fabrication of large composite structures in aeronautical industry. The carbon fiber composite parts realized with this process tend to replace the a...Automated tape placement is an important automated process used for fabrication of large composite structures in aeronautical industry. The carbon fiber composite parts realized with this process tend to replace the aluminum parts produced by high-speed machining. It is difficult to determine the appropriate width of the composite tape in automated tape placement. Wrinkling will appear in the tape if it does not suit for the mould surface. Thus, this paper deals with establishing placement suitability criteria of the composite tape for the mould surface. With the assumptions for ideal mapping and by applying some principles and theorems of differential geometry, the centerline trajectory of the composite tape is identified to follow the geodesic. The placement suitability of the composite tape is examined on three different types of non-developable mould surfaces and four criteria are derived. The developed criteria have been used to test the deposition process over several mould surfaces and the appropriate width for each mould surface is obtained by referring to these criteria.展开更多
This paper deals with the experimental investigation on Nusselt number,friction factor and thermal en-hancement factor of a double pipe heat exchanger equipped with twisted tape consisting wire nails(WN-TT) and plain ...This paper deals with the experimental investigation on Nusselt number,friction factor and thermal en-hancement factor of a double pipe heat exchanger equipped with twisted tape consisting wire nails(WN-TT) and plain twisted tapes(P-TT) with three different twist ratios of y 2.0,4.4 and 6.0. Test runs are conducted using the water as the working fluid with Reynolds number range between 2000 and 12000 for WN-TT and P-TT. It is found that Nusselt number,friction factor and thermal enhancement factor in the tube equipped with WN-TT appreciably higher than those in the tube fitted with P-TT and plain tube. Over the range considered Nusselt number,friction factor and thermal enhancement factor in a tube with WN-TT are respectively,1.08 to 1.31,1.1 to 1.75 and 1.05 to 1.13 times of those in tube with P-TT. The better performance of WN-TT is due to combined effects of the follow-ing factors:(1) common swirling flow generated by P-TT,(2) additional turbulence offered by the wire nails. Em-pirical correlations for Nusselt number,friction factor and thermal enhancement factor are also formulated from the experimental results of WN-TT and P-TT.展开更多
In this work, a multi-layer anode supported solid oxide fuel cell(SOFC) is designed and successfully prepared through sequential tape casting and co-firing. The single cell is consisted of NiO-3 YSZ(3 YSZ: 3 mol.% ytt...In this work, a multi-layer anode supported solid oxide fuel cell(SOFC) is designed and successfully prepared through sequential tape casting and co-firing. The single cell is consisted of NiO-3 YSZ(3 YSZ: 3 mol.% yttria doped zirconia) anode support, NiO-8 YSZ(8 YSZ: 8 mol.% yttria stabilized zirconia) anode functional layer, dense 8 YSZ electrolyte layer, and porous 3 YSZ cathode scaffold layer with infiltrated La_(0.6)Sr_(0.4)Co_(0.2)Fe_(0.8)O_(3-δ) cathode. The clear interfaces and good contacts between each layer, without element inter-diffusion being observed, suggest that this sequential tape casting and co-firing is a feasible and successful route for anode supported single cell fabrication. This cell exhibits remarkable high open circuit voltage of 1.097 V at 800?C under room temperature humidified hydrogen, with highly dense and gastight electrolyte layer. It provides a power density of 360 mW/cm^2 under operation voltage of0.75 V at 800?C and a stable operation of ～110 h at 750?C under current density of-300 mA/cm^2. Furthermore, this cell also presents encouraging electrochemical responses under various anode hydrogen partial pressures and maintains high power output at low fuel concentrations.展开更多
The influences of circular-ring turbulators （CRT） and twisted tape （TT） swirl generators on the heat transfer enhancement, pressure drop and thermal performance factor characteristics in a round tube are reported....The influences of circular-ring turbulators （CRT） and twisted tape （TT） swirl generators on the heat transfer enhancement, pressure drop and thermal performance factor characteristics in a round tube are reported. The circular-ring turbulators were individually employed and together with the twisted tape swirl generators in the heated section of the tube. Three different pitch ratios （I/D = 1.0, 1.5, and 2.0） of the CRT and three different twist ratios （y/W= 3, 4, and 5） of the TT were introduced. The experiments were conducted using air as the working fluid under a uniform wall heat flux condition, for the Reynolds number between 6000 and 20000. The experimental results reveal that the heat transfer rate, friction factor and thermal performance factor of the combined CRT and qT are considerably higher than those of CRT alone. For the range examined, the Sncreases of mean Nusselt number, friction factor and thermal performance, in the tube equipped with combined devices, respectively, are 25.8%, 82.8% and 6.3% over those in the tube with the CRT alone. The highest thermal performance factor of 1.42 is found for the combined device consisting of the CRT with l/D = 1.0 and TT with y/W= 3. The correlations of the Nusselt number, friction factor and thermal performance factor of the tubes with combined devices are also developed in terms of Reynolds number, Prandtl number, twist ratio and pitch ratio.展开更多
In the field of aerospace, high-speed trains and automobile, etc, analysis of temperature filed and scuffing failure of tapered roller bearings are more important than ever, and the scuffing failure of elements of suc...In the field of aerospace, high-speed trains and automobile, etc, analysis of temperature filed and scuffing failure of tapered roller bearings are more important than ever, and the scuffing failure of elements of such rolling bearings under heavy load and high speed still cannot be effectively predicted yet. A simplified model of tapered roller bearings consisted of one inner raceway, one outer raceway and a tapered roller was established, in which the interaction of several heat sources is ignored. The contact mechanics model, temperature model and model of scuffing failure are synthesized, and the corresponding computer programs are developed to analyze the effects of bearings parameters, different material and operational conditions on thermal performance of bearings, and temperature distribution and the possibility of surface scuffing are obtained. The results show that load, speed, thermal conductivity and tapered roller materials influence temperature rise and scuffing failure of bearings. Ceramic material of tapered roller results in the decrease of scuffing possibility of bearings to a high extent than the conventional rolling bearing steel. Compared with bulk temperature, flash temperature on the surfaces of bearing elements has a little influence on maximum temperature rise of bearing elements. For the rolling bearings operated under high speed and heavy load, this paper proposes a method which can accurately calculate the possibility of scuffing failure of rolling bearings.展开更多
The paper presents a 3D numerical simulation of turbulent heat transfer and flow characteristics in converging-diverging tubes （CDs） and converging-diverg）ng tubes.equi.pped with twin counter-swirling twisted tapes...The paper presents a 3D numerical simulation of turbulent heat transfer and flow characteristics in converging-diverging tubes （CDs） and converging-diverg）ng tubes.equi.pped with twin counter-swirling twisted tapes （CDTs）. The effects of Reynolds number （Re= 10000-20000）, pitch length （P= 11.25, 22.5 mm）, rib height （e = 0.5, 0.8, 1.1 ram）, pitch ratio （8= 1 ＂ 8, 5 ＂ 4, 8 ＂ 1）, gap distance between twin t）visted tapes （b = 0.5, 4.5, 8.5 mm） and tape number （n = 2, 3, 4, 5, 6） on Nusselt number （Nu）, Iriction tactor 0＇） and thermal enhancement factor （r/） are investigated under uniform heat flux conditions,using water as working fluid. In order to illustrate the heat transter and tlu^d tlow mechamsms, flow structures m ~StJs and ~SDIs are presented. The obtained results reveal that all geometric parameters have important effects on the thermal performance of CD and CDT, and both CD and CDT show better thermal performance than plain tube at the constant pumping power. It is also found that the increases in the Nusselt number and friction factor for CDT are, respectively, up to 6.3%-35.7% and 1.75-5.3 times of thecorresponding bare CD. All CDTs have good thermal perbrmance with greater than 1 which indicates that the compound heat transfer technique of CDT is commendable for the maximum enhanced heat transfer rate.展开更多
Discontinuous tape winding, which has obvious advantages in large extension ratio winding, is widely used in the molding of composites. Therefore, the research on technological parameters becomes the focus of many sch...Discontinuous tape winding, which has obvious advantages in large extension ratio winding, is widely used in the molding of composites. Therefore, the research on technological parameters becomes the focus of many scholars. However, how to accomplish the variable tension control is usually not fully considered. Accordingly, the constant extension ratio and the smoothness of winding process cannot be ensured. Aiming at the problem of tension control, this paper first gives a comparatively deep research on the control method and the interaction mechanism of tension, extension ratio, automatic lap and automatic rectification. Then, according to the winding process features, the mechanical device and the mathematical model of tension control system are established respectively. With regard to the characteristics of PID controller and fuzzy controller, the fuzzy self-tuning PID controller is designed. As a result, the variable tension control is realized during the winding and lapping process, and the constant extension ratio is guaranteed. Finally, a sample application is presented for demonstration. By presenting the variable tension control techniques for discontinuous tape winding, the constant extension ratio of tapes is achieved, the consecution and the automation degree of winding process is improved as well. Thus, the quality of wound products is guaranteed.展开更多
文摘This study involved numerical simulations of a double tube heat exchanger using the ANSYS FLUENT programversion 22.The study aims to examine methods for minimizing pressure loss and consequently enhancing the thermal performance index(TPI)of a heat exchanger fitted with wavy edge tape that is a heat recovery system(the hot air in simulation instead of t heat from the exhaust gases of the brick factory furnaces and return it to warm the heavy fuel oil by substituting the electrical heater with a heat exchanger to recuperate waste heat from the flue gases,so elevating the temperature of Heavy fuel oil(HFO)to inject from the roof nozzles of combustion chamber of the furnace furthermore reducing cost(by finding the optimal design of wavy edge tape))and energy consumption.Air was selected as the hot gas in the inner pipe instead of furnace exhaust gases due to their similar thermal characteristics.A numerical analysis was conducted to create a novel wavy edge tape with varying widths(50%Di,75%Di,and 95%Di),lengths(1000,1200,1400)mm,amplitudes(5,10,15)mm,and periods of wavy length(5,10,15)mm.The flow rate of the outer pipe fluid(oil)ranges from(0.06 to 0.1)kg/s,while the velocity of the hot fluid(air)varies from(1 to 27)m/s,Re_(air)(6957 to 187,837).The entrance temperature of the hot fluid can be either(200,225,and 250)℃.The study finds that wavy edge tape tubes are more effective than smooth tubes in terms of oil outlet temperature;results revealed that an increase in the oil mass flow rate leads to a decrease in the oil outlet temperature and an increase in the heat transfer rate,at the air temperature 250℃.Additionally,the results indicate that increasing the width,length,and amplitude also leads to an increase in the oil outlet temperature of(94-94.12)℃,the pressure drop of(568.3)Pa,and the Nusselt number(65.7-66.5)respectively on the oil side.Finally,the heat exchanger’s best thermal performance index was found by investigating temperature contour at amplitude(A=5),period(p=15),width(w=75%Di),and length(L=1200 mm).The values for these parameters are,in order(1.02,1.025,1.02,and 1.0077).
基金Project supported by the National Natural Science Foundation of China (Nos. 12232005 and 12072101)the Ningxia Natural Science Foundation of China (No. 2024AAC04004)。
文摘The fracture behavior of superconducting tapes with central and edge oblique cracks subject to electromagnetic forces is investigated. Maxwell's equations and the critical state-Bean model are used to analytically determine the magnetic flux density and electromagnetic force distributions in superconducting tapes containing central and edge oblique cracks. The distributed dislocation technique(DDT) transforms the mixed boundary value problem into a Cauchy singular integral equation, which is then solved by the Gauss-Chebyshev quadrature method to determine the stress intensity factors(SIFs).The model's accuracy is validated by comparing the calculated electromagnetic force distribution for the edge oblique crack and the SIFs for both crack types with the existing results. The findings indicate that the current and electromagnetic forces are significantly affected by the crack length and oblique angle. Specifically, for central oblique cracks, a smaller oblique angle enhances the risk of crack propagation, and a higher initial magnetization intensity poses greater danger under field cooling(FC) excitation. In contrast, for edge oblique cracks, a larger angle increases the likelihood of tape fractures. This study provides important insights into the fracture behavior and mechanical failure mechanisms of superconducting tapes with oblique cracks.
文摘Heat transfer,friction factor and thermal enhancement factor characteristics of a double pipe heat exchanger fitted with square-cut twisted tapes（STT） and plain twisted tapes（PTT） are investigated experimentally using the water as working fluid.The tapes（STT and PTT） have three twist ratios（y=2.0,4.4 and 6.0） and the Reynolds number ranges from 2000 to 12000.The experimental results reveal that heat transfer rate,friction factor and thermal enhancement factor in the tube equipped with STT are significantly higher than those fitted with PTT. The additional disturbance and secondary flow in the vicinity of the tube wall generated by STT are higher compared to that induced by the PTT is referred as the reason for better performance.Over the range considered,the Nusselt number,friction factor and thermal enhancement factor in a tube with STT are respectively,1.03 to 1.14,1.05 to 1.25 and 1.02 to 1.06 times of those in tube with PTT.An empirical correlation is also formulated to match with experimental data of Nusselt number and friction factor for STT and PTT.
基金National High-Tech Research and Development Program Special Foundation of China(2002AA334130)
文摘This article introduces a computer numerical control （CNC）-based open hardware architecture system to realize the special functions of automated tape-laying （ATL） in a numerical control system. It associates a programmable multi-axis controller （PMAC） as the motion control unit with programmable numerical controllers （PCL-725, PCL-730） for on-off control. To bring about synchronized movements of the main 5-axis tape-laying head system and the 3-axis ultrasonic tape-cutting sub-system, the tracking-control method associated with time-based mode attributed to PMAC is applied in different cases. In addition, with the goal of realizing real-time tasks in the software system such as synchronizing motion control and on-off control, the real-time Win 2000 system is adopted. As a device driver for PMAC and PCL, a user graphical interface and a numerical control program interpretation module are also designed. This system is helpful to solve complicated problems in designing numerical controls for ATL such as ensuring high requirements for precise machine control and synchronization of motion control and on-off control.
文摘Heat augmentation techniques play a vital role in the heating and cooling processes in industries,including solar collectors and many applications that utilize heat exchangers.Several studies are based on inserting fillers inside the tubes to enhance heat transfer.This investigation considered the effects of twisted tapes with large holes on a tubular heat exchanger’s(HX)heat transmission,pressure drop,and thermal boosting factor.In the experimental section,counter-swirl flow generators used twisted tapes with pairs of 1.0 cm-diameter holes and changes in porosity(Rp)at 1.30%and 2.70%.In the experiments,air was utilized as a working fluid in a tube with a circular cross-section.The turbulent flow was considered,with Reynolds numbers(Re)domain from 4800 to 9500,and a boundary condition with a uniform wall heat flux was constructed.The findings expound that when the number of holes rose,the Nusselt number(Nu),the factor of friction(f),and the thermal enhancement factor(η)all increased as well.Additionally,as the friction factor increased,the Nusselt number of the tape-equipped tube was noticeably higher.Additionally,it was discovered that the friction factor was between 70%and 94%lower than the values of the tube without tape,while the(Nu)was between 87%and 97%higher than the conventional tube values.The maximum value ofηis 89%.According to the experimental results,empirical correlations for Nu,f,andηwere also generated.
文摘Three kinds of silver-sheathed Bi(2223) oxide superconductor tapes (single-core tape, Ag-powder-added tape and multifilamentary type) were successfully prepared, namely, through the powder-in-tube method. The critical current density (Jc), the Jc-B characteristics, microstructures and the relation between Jc and strain of three kinds of tapes were evaluated and compared. The maximum Jc of three kinds of tapes at 77.7 K in zero magnetic field are 28700 A/cm2 for single-core tape, 20800 A/cm2 for Ag-powder-added tape, 11700 A/cm2 for multifilamentary tape. Single-core tapes exhibit high Jc values and good Jc-B characteristics.
文摘The purpose of this paper is to demonstrate and investigate the concepts of new deployable boom systems, which consist of the BCON （braid coated bi-convex tape） boom and the SMA-BCON （braid coated bi-shape memory alloy convex tape） boom. Both booms are developed for the deployable membrane structures such as solar sails, thin membrane solar array panels, deorbit mechanisms for small satellites and reflectors of space solar power satellite, etc. BCON booms can store around polygonal or cylindrical center hub, and the booms can deploy by the stepwise manner by releasing a constraint mechanism which pins the boons into two or three points for the total length. SMA-BCON booms are mainly developed for a square center body systems, and SMA is adapted on the bent po^nts of the booms where stored around each edge of the center hub. Through the deployment experiments of both booms, the stepwise deployment behavior and its tendency are obtained. The design concept of BCON boom and SMA-BCON hnnm i~ demonstrated through this study.
基金supported by the National Natural Science Foundation of China(40771097)the Special Fund of Industrial(Agriculture)Research for Public Welfare of China(200903001)
文摘More and more attention is being focused on saline water utilization in irrigation due to the shortage of fresh water to agriculture in many regions. For purpose of reducing the risks of using of saline water for irrigation, the mechanism of soil moisture and salinity distribution and transport should be well understood for developing optimum management strategies. In this paper, field experiments were carried out at Junggar Basin, China, to study the effects of drip irrigation water quality and drip tape arrangement on distribution of soil salinity and soil moisture. Six treatments were designed, including two drip tape arrangement modes and three irrigation water concentration levels （0.24, 4.68, and 7.42 dS m^-l）. Results showed that, soil moisture content （SMC） directly beneath the drip tape in all treatments kept a relatively high value about 18% before boll opening stage; the SMC in the narrow strip in single tape arrangement （Ms） plot was obviously lower than that in the double tapes arrangement （Md） plot, indicating that less sufficient water was supplied under the same condition of irrigation depth, but there was no significant reduction in yield. Mulching had not significant influence on salt accumulation but the drip tape arrangement, under the same condition of irrigation water depth and quality, compared with Md, Ms reduced salt accumulation in root zone and brought about relatively high cotton yield.
基金supported by the National Basic Research Program of China (No. 2013CB035805)the National Science and Technology Major Project of China (2010ZX04016-013)
文摘Automated tape placement is an important automated process used for fabrication of large composite structures in aeronautical industry. The carbon fiber composite parts realized with this process tend to replace the aluminum parts produced by high-speed machining. It is difficult to determine the appropriate width of the composite tape in automated tape placement. Wrinkling will appear in the tape if it does not suit for the mould surface. Thus, this paper deals with establishing placement suitability criteria of the composite tape for the mould surface. With the assumptions for ideal mapping and by applying some principles and theorems of differential geometry, the centerline trajectory of the composite tape is identified to follow the geodesic. The placement suitability of the composite tape is examined on three different types of non-developable mould surfaces and four criteria are derived. The developed criteria have been used to test the deposition process over several mould surfaces and the appropriate width for each mould surface is obtained by referring to these criteria.
文摘This paper deals with the experimental investigation on Nusselt number,friction factor and thermal en-hancement factor of a double pipe heat exchanger equipped with twisted tape consisting wire nails(WN-TT) and plain twisted tapes(P-TT) with three different twist ratios of y 2.0,4.4 and 6.0. Test runs are conducted using the water as the working fluid with Reynolds number range between 2000 and 12000 for WN-TT and P-TT. It is found that Nusselt number,friction factor and thermal enhancement factor in the tube equipped with WN-TT appreciably higher than those in the tube fitted with P-TT and plain tube. Over the range considered Nusselt number,friction factor and thermal enhancement factor in a tube with WN-TT are respectively,1.08 to 1.31,1.1 to 1.75 and 1.05 to 1.13 times of those in tube with P-TT. The better performance of WN-TT is due to combined effects of the follow-ing factors:(1) common swirling flow generated by P-TT,(2) additional turbulence offered by the wire nails. Em-pirical correlations for Nusselt number,friction factor and thermal enhancement factor are also formulated from the experimental results of WN-TT and P-TT.
基金supported financially by the Key R & D Program of Jiangsu Province (No.BE2017098)the Natural Science Foundation of Jiangsu Province (No.BK20170847)+1 种基金the Top-notch Academic Programs Project of Jiangsu Higher Education Institutionsthe Start-Up Fund of Nanjing University of Science and Technology
文摘In this work, a multi-layer anode supported solid oxide fuel cell(SOFC) is designed and successfully prepared through sequential tape casting and co-firing. The single cell is consisted of NiO-3 YSZ(3 YSZ: 3 mol.% yttria doped zirconia) anode support, NiO-8 YSZ(8 YSZ: 8 mol.% yttria stabilized zirconia) anode functional layer, dense 8 YSZ electrolyte layer, and porous 3 YSZ cathode scaffold layer with infiltrated La_(0.6)Sr_(0.4)Co_(0.2)Fe_(0.8)O_(3-δ) cathode. The clear interfaces and good contacts between each layer, without element inter-diffusion being observed, suggest that this sequential tape casting and co-firing is a feasible and successful route for anode supported single cell fabrication. This cell exhibits remarkable high open circuit voltage of 1.097 V at 800?C under room temperature humidified hydrogen, with highly dense and gastight electrolyte layer. It provides a power density of 360 mW/cm^2 under operation voltage of0.75 V at 800?C and a stable operation of ～110 h at 750?C under current density of-300 mA/cm^2. Furthermore, this cell also presents encouraging electrochemical responses under various anode hydrogen partial pressures and maintains high power output at low fuel concentrations.
文摘The influences of circular-ring turbulators （CRT） and twisted tape （TT） swirl generators on the heat transfer enhancement, pressure drop and thermal performance factor characteristics in a round tube are reported. The circular-ring turbulators were individually employed and together with the twisted tape swirl generators in the heated section of the tube. Three different pitch ratios （I/D = 1.0, 1.5, and 2.0） of the CRT and three different twist ratios （y/W= 3, 4, and 5） of the TT were introduced. The experiments were conducted using air as the working fluid under a uniform wall heat flux condition, for the Reynolds number between 6000 and 20000. The experimental results reveal that the heat transfer rate, friction factor and thermal performance factor of the combined CRT and qT are considerably higher than those of CRT alone. For the range examined, the Sncreases of mean Nusselt number, friction factor and thermal performance, in the tube equipped with combined devices, respectively, are 25.8%, 82.8% and 6.3% over those in the tube with the CRT alone. The highest thermal performance factor of 1.42 is found for the combined device consisting of the CRT with l/D = 1.0 and TT with y/W= 3. The correlations of the Nusselt number, friction factor and thermal performance factor of the tubes with combined devices are also developed in terms of Reynolds number, Prandtl number, twist ratio and pitch ratio.
基金Supported by the Natural Science Foundation of China (Grant No.51375436)Natural Science Foundation of Zhejiang Province (Grant No.Z1100475)Project of Engineering Research Center for Sliding Bearing of Zhejiang Province (Contract No.2012E10028)
文摘In the field of aerospace, high-speed trains and automobile, etc, analysis of temperature filed and scuffing failure of tapered roller bearings are more important than ever, and the scuffing failure of elements of such rolling bearings under heavy load and high speed still cannot be effectively predicted yet. A simplified model of tapered roller bearings consisted of one inner raceway, one outer raceway and a tapered roller was established, in which the interaction of several heat sources is ignored. The contact mechanics model, temperature model and model of scuffing failure are synthesized, and the corresponding computer programs are developed to analyze the effects of bearings parameters, different material and operational conditions on thermal performance of bearings, and temperature distribution and the possibility of surface scuffing are obtained. The results show that load, speed, thermal conductivity and tapered roller materials influence temperature rise and scuffing failure of bearings. Ceramic material of tapered roller results in the decrease of scuffing possibility of bearings to a high extent than the conventional rolling bearing steel. Compared with bulk temperature, flash temperature on the surfaces of bearing elements has a little influence on maximum temperature rise of bearing elements. For the rolling bearings operated under high speed and heavy load, this paper proposes a method which can accurately calculate the possibility of scuffing failure of rolling bearings.
基金Supported by the Science and Technology Key Projects of Shanxi Province(2011A080804012)
文摘The paper presents a 3D numerical simulation of turbulent heat transfer and flow characteristics in converging-diverging tubes （CDs） and converging-diverg）ng tubes.equi.pped with twin counter-swirling twisted tapes （CDTs）. The effects of Reynolds number （Re= 10000-20000）, pitch length （P= 11.25, 22.5 mm）, rib height （e = 0.5, 0.8, 1.1 ram）, pitch ratio （8= 1 ＂ 8, 5 ＂ 4, 8 ＂ 1）, gap distance between twin t）visted tapes （b = 0.5, 4.5, 8.5 mm） and tape number （n = 2, 3, 4, 5, 6） on Nusselt number （Nu）, Iriction tactor 0＇） and thermal enhancement factor （r/） are investigated under uniform heat flux conditions,using water as working fluid. In order to illustrate the heat transter and tlu^d tlow mechamsms, flow structures m ~StJs and ~SDIs are presented. The obtained results reveal that all geometric parameters have important effects on the thermal performance of CD and CDT, and both CD and CDT show better thermal performance than plain tube at the constant pumping power. It is also found that the increases in the Nusselt number and friction factor for CDT are, respectively, up to 6.3%-35.7% and 1.75-5.3 times of thecorresponding bare CD. All CDTs have good thermal perbrmance with greater than 1 which indicates that the compound heat transfer technique of CDT is commendable for the maximum enhanced heat transfer rate.
基金supported by Shaanxi Provincial "13115" Important Scientific and Technological Innovation Fund of China (Grant No. 2009ZDKG-27)
文摘Discontinuous tape winding, which has obvious advantages in large extension ratio winding, is widely used in the molding of composites. Therefore, the research on technological parameters becomes the focus of many scholars. However, how to accomplish the variable tension control is usually not fully considered. Accordingly, the constant extension ratio and the smoothness of winding process cannot be ensured. Aiming at the problem of tension control, this paper first gives a comparatively deep research on the control method and the interaction mechanism of tension, extension ratio, automatic lap and automatic rectification. Then, according to the winding process features, the mechanical device and the mathematical model of tension control system are established respectively. With regard to the characteristics of PID controller and fuzzy controller, the fuzzy self-tuning PID controller is designed. As a result, the variable tension control is realized during the winding and lapping process, and the constant extension ratio is guaranteed. Finally, a sample application is presented for demonstration. By presenting the variable tension control techniques for discontinuous tape winding, the constant extension ratio of tapes is achieved, the consecution and the automation degree of winding process is improved as well. Thus, the quality of wound products is guaranteed.
