In this study,we numerically investigate the droplet impact onto a thin liquid film deposited on a structured surface with square pillars and cavities.The time evolution of crown geometry is strongly affected by the s...In this study,we numerically investigate the droplet impact onto a thin liquid film deposited on a structured surface with square pillars and cavities.The time evolution of crown geometry is strongly affected by the surface structure.When the thickness of the liquid film is larger than the structure height,the expanding speed of the crown base radius is independent of the structure width.However,if the liquid film thickness is equal to the structure height,the crown base expands slower as the structure width increases.Surface structures have strong effects on the crown height and radius,and can prevent ejected filament from breaking into satellite droplets for certain cases.For the liquid film with the thickness equal to the pillar height,both the crown height and the radius exhibit non-monotonic behaviors as the pillar width increases.There exists one pillar width which produces the smallest crown height and the largest crown radius.展开更多
This paper proposes an investigation of the effects of laser engineering surface with dimple operating under lubrication. Dimples with semi-spherical geometry, with 100 μm in diameter and 25 μm in depth, were Laser-...This paper proposes an investigation of the effects of laser engineering surface with dimple operating under lubrication. Dimples with semi-spherical geometry, with 100 μm in diameter and 25 μm in depth, were Laser-machined on the surfaces of high speed steel AISI H 13 discs, with three different distribution densities applied over the surface. Pin-on-disc experiments were performed by using counter bodies made with AISI 440C and Tungsten carbide ISO K20 pins. The experiments provided data information on the influence of dimple distribution on the coefficient of friction. Numerical simulations were performed to understand the influence of the pin and disc surface roughness on the contact problem. The results suggest that the design of dimple-structured surfaces rely on nine main parameters： material contact pair and its respective hardness, Young Modulus, the roughness of the surfaces, the dimple design, the dimple distribution, the load applied, the velocity and the type of lubricant. A better performance can be obtained from a compromise solution over these parameters, and the dimple concentration has a dominance over the other parameters. The best results were obtained with a lower concentration of dimples, under higher speed and load. Numerical simulations can also be used as a design tool, supporting decisions regarding shape and distribution of the dimples and material selections for the contact pair.展开更多
Nanostructured surface is a promising photon management strategy to tune spectrum in design of the selective solar absorber.In this paper,we propose a nanocone structured surface as a perfect solar absorber in applica...Nanostructured surface is a promising photon management strategy to tune spectrum in design of the selective solar absorber.In this paper,we propose a nanocone structured surface as a perfect solar absorber in application of the solar thermoelectric generators(STEGs).The trade-off between the solar absorption and the mid-infrared emission is obtained to maximize the STEG efficiency.The effects of the geometric parameters,thermal concentration,incident angle and polarized state as well as the lattice arrangement are systematically investigated.The results show that the STEGs equipped with our proposed selective solar absorber can achieve a peak efficiency of 6.53%under AM1.5G condition(no optical concentration).Furthermore,the selective solar absorber exhibits insensitive behavior to the incident angle and polarization angle as well.This means that the proposed selective solar absorber can utilize solar energy as much as possible and be generally suitable in equipping the STEGs without optical concentration.展开更多
Electrochemical oxidation/reduction of radicals is a green and environmentally friendly approach to generating fuels.These reactions,however,suffer from sluggish kinetics due to a low local concentration of radicals a...Electrochemical oxidation/reduction of radicals is a green and environmentally friendly approach to generating fuels.These reactions,however,suffer from sluggish kinetics due to a low local concentration of radicals around the electrocatalyst.A large applied electrode potential can enhance the fuel generation efficiency via enhancing the radical concentration around the electrocatalyst sites,but this comes at the cost of electricity.Here,we report about a~45%saving in energy to achieve an electrochemical hydrogen generation rate of 3×10^(16) molecules cm^(–2)s^(–1)(current density:10 mA/cm^(2))through localized electric field-induced enhancement in the reagent concentration(LEFIRC)at laser-induced periodic surface structured(LIPSS)electrodes.The finite element model is used to simulate the spatial distribution of the electric field to understand the effects of LIPSS geometric parameters in field localization.When the LIPSS patterned electrodes are used as substrates to support Pt/C and RuO_(2) electrocatalysts,the η_(10) overpotentials for HER and OER are decreased by 40.4 and 25%,respectively.Moreover,the capability of the LIPSS-patterned electrodes to operate at significantly reduced energy is also demonstrated in a range of electrolytes,including alkaline,acidic,neutral,and seawater.Importantly,when two LIPSS patterned electrodes were assembled as the anode and cathode into a cell,it requires 330 mVs of lower electric potential with enhanced stability over a similar cell made of pristine electrodes to drive a current density of 10 mA/cm^(2).This work demonstrates a physical and versatile approach of electrode surface patterning to boost electrocatalytic fuel generation performance and can be applied to any metal and semiconductor catalysts for a range of electrochemical reactions.展开更多
Hydrogel scaffolds have numerous potential applications in the tissue engineering field.However,tough hydrogel scaffolds implanted in vivo are seldom reported because it is difficult to balance biocompatibility and hi...Hydrogel scaffolds have numerous potential applications in the tissue engineering field.However,tough hydrogel scaffolds implanted in vivo are seldom reported because it is difficult to balance biocompatibility and high mechanical properties.Inspired by Chinese ramen,we propose a universal fabricating method(printing-P,training-T,cross-linking-C,PTC&PCT)for tough hydrogel scaffolds to fill this gap.First,3D printing fabricates a hydrogel scaffold with desired structures(P).Then,the scaffold could have extraordinarily high mechanical properties and functional surface structure by cycle mechanical training with salting-out assistance(T).Finally,the training results are fixed by photo-cross-linking processing(C).The tough gelatin hydrogel scaffolds exhibit excellent tensile strength of 6.66 MPa(622-fold untreated)and have excellent biocompatibility.Furthermore,this scaffold possesses functional surface structures from nanometer to micron to millimeter,which can efficiently induce directional cell growth.Interestingly,this strategy can produce bionic human tissue with mechanical properties of 10 kPa-10 MPa by changing the type of salt,and many hydrogels,such as gelatin and silk,could be improved with PTC or PCT strategies.Animal experiments show that this scaffold can effectively promote the new generation of muscle fibers,blood vessels,and nerves within 4 weeks,prompting the rapid regeneration of large-volume muscle loss injuries.展开更多
This paper discusses the coloration process on the stainless steel and the properties of the film. The compositions, morphology and structure of colored films on stainless steel are studied by using SEM,AES,AFM,STM. ...This paper discusses the coloration process on the stainless steel and the properties of the film. The compositions, morphology and structure of colored films on stainless steel are studied by using SEM,AES,AFM,STM. The diffusion controlled mechanisms of films and calculation formula of surface electropotential difference are discussed.展开更多
Paint removal from steel structure is executed for shipyards of marine and offshore engineering.Due to environmental unfriendliness and unhealthy drawbacks of sand blasting technique, laser ablation technique is propo...Paint removal from steel structure is executed for shipyards of marine and offshore engineering.Due to environmental unfriendliness and unhealthy drawbacks of sand blasting technique, laser ablation technique is proposed as a substituting method.By absorbing high energy of the 1064 nm pulsed laser, the paint is vaporized quickly.The ablated debris is then collected by using a suction pump.Initial metal surface of the steel is exposed when laser beam irradiates perpendicularly and scans over it.The cleaned surface fulfills the requirements of surface preparation standards ISO 8501 of SA2.The adhesion is further characterized with pull-off test after carrying out painting with Jotamastic 87 aluminum paint.The repainting can be embedded onto the laser cleaned surface to bond much more tightly.The excellent adhesion strength of 20 MPa between repainted coating and the substrate is achieved, which is higher than what is required by shipyards applications.展开更多
An essential step for the realization of free-form surface structures is to create an efficient structural gird that satisfies not only the architectural aesthetics,but also the structural performance.Employing the ma...An essential step for the realization of free-form surface structures is to create an efficient structural gird that satisfies not only the architectural aesthetics,but also the structural performance.Employing the main stress trajectories as the representation of force flows on a free-form surface,an automatic grid generation approach is proposed for the architectural design.The algorithm automatically plots the main stress trajectories on a 3D free-form surface,and adopts a modified advancing front meshing technique to generate the structural grid.Based on the proposed algorithm,an automatic grid generator named "St-Surmesh" is developed for the practical architectural design of free-form surface structure.The surface geometry of one of the Sun Valleys in Expo Axis for the Expo Shanghai 2010 is selected as a numerical example for validating the proposed approach.Comparative studies are performed to demonstrate how different structural grids affect the design of a free-form surface structure.展开更多
Inhomogeneity and low efficiency are two important factors that limit the application of laser-induced periodic surface structures(LIPSSs),especially on glass surfaces.In this study,two-beam interference(TBI)of femtos...Inhomogeneity and low efficiency are two important factors that limit the application of laser-induced periodic surface structures(LIPSSs),especially on glass surfaces.In this study,two-beam interference(TBI)of femtosecond lasers was used to produce large-area straight LIPSSs on fused silica using cylindrical lenses.Compared with those produced us-ing a single circular or cylindrical lens,the LIPSSs produced by TBI are much straighter and more regular.Depending on the laser fluence and scanning velocity,LIPSSs with grating-like or spaced LIPSSs are produced on the fused silica sur-face.Their structural colors are blue,green,and red,and only green and red,respectively.Grating-like LIPSS patterns oriented in different directions are obtained and exhibit bright and vivid colors,indicating potential applications in surface coloring and anti-counterfeiting logos.展开更多
Biochars are known for their heterogeneity, especially in pore and surface structure associated with pyrolysis processes and sources of feedstocks. The surface area of biochar is likely to be an important determinant ...Biochars are known for their heterogeneity, especially in pore and surface structure associated with pyrolysis processes and sources of feedstocks. The surface area of biochar is likely to be an important determinant of the extent of soil microbial attachment, whereas the porous structure of biochar is expected to provide protection for soil microorganisms. Potential interactions between biochars from different sources and with different particle sizes were investigated in relation to soil microbial properties in a short-term incubation study. Three particle size （sieved） fractions （0.5-1.0, 1.0-2.0 and 2.0-4.0 mm） from three woody biochars produced from jarrah wood, jarrah and wandoo wood and Australian wattle branches, respectively, were incubated in soil at 25 ℃ for 56 d. Observation by scanning electron microscopy （SEM） and characterisation of pore and surface area showed that all three woody biochars provided potential habitats for soil microorganisms due to their high porosity and surface areas. The biochars were structurally heterogeneous, varying in porosity and surface structure both within and between the biochar sources. After the 56-d incubation, hyphal colonisation was observed on biochar surfaces and in larger biochar pores. Soil clumping occurred on biochar particles, cementing and covering exposed biochar pores. This may have altered surface area and pore availability for microbial colonisation. Transient changes in soil microbial biomass, without a consistent trend, were observed among biochars during the 56-d incubation.展开更多
Titanium alloys have a wide application in aerospace industries as it has greater strength and low density, but it has poor tribological properties. To improve its friction and wear performance, in present work, a fem...Titanium alloys have a wide application in aerospace industries as it has greater strength and low density, but it has poor tribological properties. To improve its friction and wear performance, in present work, a femtosecond laser is used to directly irradiate the Ti6Al4V titanium alloy surface in air conditioning, which results in localized ablation and the formation of periodic microstructures but also a strong pressure wave, propagating the material inside. Through the optimization of processing parameters, surface modification and periodic micropatterning with effective anti-friction properties were successfully induced on the surface. After a treatment of femtosecond laser-induced surface modification(FsLSM), the surface microhardness was improved by 16.6% and compressive residual stress reached-746 MPa. Besides, laser-induced periodic surface structures(LIPSS) with a titanium oxide outer coating were fabricated uniformly on the titanium alloy surface. Rotary ball-on-disk wear experiments revealed that the average coefficient of friction(COF) and wear mass loss of the specimen with Fs LSM treatment were largely reduced by 68.9% and 90% as compared to that of untreated specimens, respectively. It was analyzed that the reason for the remarkable wear resistance was attributed to the comprehensive action of the generation of LIPSS, the titanium oxide outer coating, high amplitude compressive residual stress and gradient grain size distribution on the subsurface during the laser surface treatment. Since the findings here are broadly applicable to a wide spectrum of engineering metals and alloys, the present results offer unique pathways to enhancing the tribological performance of materials.展开更多
Femtosecond laser pulses with GHz burst mode that consist of a series of trains of ultrashort laser pulses with a pulse interval of several hundred picoseconds offer distinct features in material processing that canno...Femtosecond laser pulses with GHz burst mode that consist of a series of trains of ultrashort laser pulses with a pulse interval of several hundred picoseconds offer distinct features in material processing that cannot be obtained by the conventional irradiation scheme of femtosecond laser pulses(single-pulse mode).However,most studies using the GHz burst mode femtosecond laser pulses focus on ablation of materials to achieve high-efficiency and high-quality material removal.In this study,we explore the ability of the GHz burst mode femtosecond laser processing to form laser-induced periodic surface structures(LIPSS)on silicon.It is well known that the direction of LIPSS formed by the single-pulse mode with linearly polarized laser pulses is typically perpendicular to the laser polarization direction.In contrast,we find that the GHz burst mode femtosecond laser(wavelength:1030 nm,intra-pulse duration:220 fs,intra-pulse interval time(intra-pulse repetition rate):205 ps(4.88 GHz),burst pulse repetition rate:200 kHz)creates unique two-dimensional(2D)LIPSS.We regard the formation mechanism of 2D LIPSS as the synergetic contribution of the electromagnetic mechanism and the hydrodynamic mechanism.Specifically,generation of hot spots with highly enhanced electric fields by the localized surface plasmon resonance of subsequent pulses in the bursts within the nanogrooves of one-dimensional LIPSS formed by the preceding pulses creates 2D LIPSS.Additionally,hydrodynamic instability including convection flow determines the final structure of 2D LIPSS.展开更多
The shock wave of the underwater explosion can cause severe damage to the ship structure.The propagation characteristics of shock waves near the structure surface are complex,involving lots of complex phenomena such a...The shock wave of the underwater explosion can cause severe damage to the ship structure.The propagation characteristics of shock waves near the structure surface are complex,involving lots of complex phenomena such as reflection,transmission,diffraction,and cavitation.However,different structure surface boundaries have a significant effect on the propagation characteristics of pressure.This paper focuses on investigating the behavior of shock wave propagation and cavitation from underwater explosions near various structure surfaces.A coupled Runge–Kutta discontinuous Galerkin(RKDG)and finite elementmethod(FEM)is utilized to solve the problem of the complex waves of fluids and structure dynamic response,considering the fluid compressibility.The level set(LS)method and the ghost fluid(GF)method are combined to capture the moving interface and deal with the stability of the coupling between the shock wave and structure surface.Besides,a cut-off cavitation model is introduced to the RKDG method.The validation of the numerical calculation model is discussed by comparing it with the known solution to verify the numerical solutions.Then,crucial kinds of structure surface boundary conditions include shallow-water single layer elasticity plate,double-layer crevasse elasticity plate,single layer curved elasticity plate,and double-layer curved elasticity plates are analyzed and discussed.The results and analysis can provide references for underwater explosion pressure characteristics,the impacting response of different boundary structures,and designing structures.展开更多
It is of a vital importance to reduce the frictional losses in marine diesel engines. Advanced surface textures have provided an e ective solution to friction performance of rubbing pairs due to the rapid development ...It is of a vital importance to reduce the frictional losses in marine diesel engines. Advanced surface textures have provided an e ective solution to friction performance of rubbing pairs due to the rapid development of surface engineering techniques. However,the mechanisms through which textured patterns and texturing methods prove beneficial remains unclear. To address this issue,the tribological system of the cylinder liner?piston ring(CLPR) is investigated in this work. Two types of surface textures(Micro concave,Micro V?groove) are processed on the cylinder specimen using di erent processing methods. Comparative study on the friction coe cients,worn surface texture features and oil film characteristics are performed. The results demonstrate that the processing method of surface texture a ect the performance of the CLPR pairs under the specific testing conditions. In addition the micro V?groove processed by CNCPM is more favorable for improving the wear performances at the low load,while the micro?con?cave processed by CE is more favorable for improving the wear performances at the high load. These findings are in helping to understand the e ect of surface texture on wear performance of CLPR.展开更多
Ball burnishing is a plastic deformation process used as a surface smoothing and surface improvement finishing treatment after turning or milling processes. This process changes the surface stereometrics of the previo...Ball burnishing is a plastic deformation process used as a surface smoothing and surface improvement finishing treatment after turning or milling processes. This process changes the surface stereometrics of the previously machining surface. Burnishing with hydrostatic tools can be easily and effectively used on both conventional and Computer Numeric Control(CNC) machines. The existing research of the burnishing process mainly focuses on the functional surface characterization, for example, surface roughness, wear resistance, surface layer hardness, etc. There is a lack of references reporting a detailed analysis of 3D parameters calculation with a mathematical model to evaluate the results of the ball burnishing. This paper presents the effect of ball burnishing process parameters with hydrostatic tools on the resulting surface structure geometry. The surface topography parameters were calculated using the Taly Map software. Studies were conducted based on Hartley’s static, determined plan. Such a plan can be built on a hypersphere or hypercube. In this work, a hypercube was used. In the case of Hartley’s plan makes it possible to define the regression equation in the form of a polynomial of the second degree. The input process parameters considered in this study include the burnishing rate, applied pressure, and line-to-line pitch. The significant influence of these parameters was confirmed and described as a mathematical power model. The results also showed a positive effect of hydrostatic burnishing on the roughness and geometric structure of the surface.展开更多
The poor wear resistance and bio-inertness surface of polyetheretherketone(PEEK)limits the implant applications of PEEK and its composites.Carbon fiber(CFR)was used to boost the wear resistance of PEEK;however,the bio...The poor wear resistance and bio-inertness surface of polyetheretherketone(PEEK)limits the implant applications of PEEK and its composites.Carbon fiber(CFR)was used to boost the wear resistance of PEEK;however,the bioactivity of carbon fiber-reinforced polyetheretherketone(CFR-PEEK)composites is even worse.The bioactivity of CFR-PEEK can be enhanced by constructing 3D porous structure.Nevertheless,large number of sulfur component introduced by sulfonation shows cytotoxicity and can cause damage to human cells.Besides,the sulfur component affects the cytotoxicity and bioactivity of sulfonated CFR-PEEK(SCFR-PEEK).Hydrothermal treatment can sweep away the sulfur component in the 3D porous structure of SCFR-PEEK.Meanwhile,the changes in crystallinity and hardness after hydrothermal treatment may also affect the wear resistance.Therefore,the effect of hydrothermal temperature on wear resistance,cytotoxicity and bioactivity of SCFR-PEEK were studied.In this work,the samples with hydrothermal temperature 90–120℃exhibited high wear resistance.The 3D pore structure of SCFR-PEEK unchanged after hydrothermal treatment,and the sulfur component in the 3D pore structure gradually decreased with increasing hydrothermal temperature by SEM images and EDS analysis.In addition,SCFR-PEEK treated in 90–120℃.Exhibited low cytotoxicity and high bioactivity,which is beneficial for the implant materials.展开更多
Selective hydrogenation of substituted nitroarenes is an important reaction to obtain amines.Supported metal catalysts are wildly used in this reaction because the surface structure of supports can tune the properties...Selective hydrogenation of substituted nitroarenes is an important reaction to obtain amines.Supported metal catalysts are wildly used in this reaction because the surface structure of supports can tune the properties of the supported metal nanoparticles(NPs)and promote the selectivity to amines.Herein,Pt NPs were immobilized on Fe OOH,Fe_(3)O_(4)andα-Fe_2O_(3)nanorods to synthesize a series of iron compounds supported Pt catalysts by liquid phase reduction method.Chemoselective hydrogenation of 3-nitrostyrene to 3-aminostyrene was used as probe reaction to evaluate the performance of the catalysts.The results show that Pt/Fe OOH exhibits the highest selectivity and activity.Fe OOH support with pores and-OH groups can tune the electronic structure of Pt NPs.The positive charge of Pt NPs supported on Fe OOH is key factor for improving the catalytic performance.展开更多
Surface structural engineering is desirable in modifying the surface performance of carbonyl iron powder(CIP)to enhance microwave absorption(MA)and anti-oxidation performance.Herein,the surface shape-dependent CIP abs...Surface structural engineering is desirable in modifying the surface performance of carbonyl iron powder(CIP)to enhance microwave absorption(MA)and anti-oxidation performance.Herein,the surface shape-dependent CIP absorbers are designed via surface coating with zinc oxide(ZnO)nanoparticles and then a thermal annealing treatment.The morphology of ZnO nanoparticles which can be easily regulated by controlling the annealing temperature ultimately affects the MA performance of CIP coating with ZnO nanoparticles(CIP@ZnO).The core-shell CIP@ZnO particles with cubic cone ZnO nanoparticles exhibit ex-cellent MA performance and thermal stability in comparison to the original CIP.Specifically,the CIP@ZnO annealed at 350 ℃(CIP@ZnO-350)samples which have the cubic cone ZnO nanoparticles exhibit a min-imum reflection loss(RLmin)of-55.35 dB at a thickness of 2.1 mm and a maximum effective absorp-tion bandwidth(EAB)of 7.09 GHz at a thickness of 2.0 mm.In addition,the antioxidant property of the CIP@ZnO composite particles is abruptly enhanced,which breaks the restriction of the application of CIP at high temperatures.The superior MA performance of CIP@ZnO particles with cubic cone ZnO nanoparti-cles comes from the enhancement in surface shape-dependent multiple microwave scattering,interfacial polarization,and electromagnetic-dielectric synergism between ZnO and CIP.展开更多
The aim of this study was to reconstruct surface porous structure with hundreds of micrometers and then bio-mineralize Sr-doped Calcium Phosphate(Sr-doped CaP)on Polyetheretherketone(PEEK)profile to enhance its bioact...The aim of this study was to reconstruct surface porous structure with hundreds of micrometers and then bio-mineralize Sr-doped Calcium Phosphate(Sr-doped CaP)on Polyetheretherketone(PEEK)profile to enhance its bioactivity.A surface porous structure was prepared on PEEK profile by embedding and acid-etching of SiO2 particles as porogen(SP-PEEK).Then the Sr-doped CaP was further decorated on the porous surface after sulfonation,introduction of Sr-doped CaP crystal seeds and bio-mineralization in 1.5 times simulated body fluid(BSSP-PEEK-CaP/Sr).It was feasible to reconstruct the surface porous structure with hundreds of micrometers on PEEK profile by the present method without damaging its mechanical properties.The Sr-doped CaP crystal seeds effectively promoted the bio-mineralization of bio-inertness PEEK.All as-prepared PEEK did not inhibit the proliferation of cells.ALP of bio-mineralized groups was significantly increased than that of the other groups.The BSSP-PEEK-CaP/Sr obviously affected the morphology and promoted the adhesion and spreading of cells.As a result,the cyto-biocompatibity and bioactivity of PEEK were improved after bio-mineralization.Sr-doped CaP on PEEK most likely was beneficial for cells,which was associated with the increasing of the hydrophilicity on PEEK.This study provided a candidate method to improve the osteogenesis of PEEK implants.展开更多
The three-way catalysts （TWCs） promoters Ce0.6Zr0.4- x TbxO2-y were prepared by sol-gel method. BET surface areas analysis indicated that an increase of the dopant Tb content from x = 0.05 to x = 0.15 favors an incr...The three-way catalysts （TWCs） promoters Ce0.6Zr0.4- x TbxO2-y were prepared by sol-gel method. BET surface areas analysis indicated that an increase of the dopant Tb content from x = 0.05 to x = 0.15 favors an increase of surface area from 66.8 to 80.4 m^2· g^-1 compared with the undoped sample Ce0 .6oZr0.40O2 65.1 m^2·g^- 1 after calcination at 650℃. Transmission electron microscopy （TEM） observation indicated that the doped samples have a higher thermal stability. The XRD and Raman spectra confirmed that the Ce0.6Zr0.4-xTbxO2-y cubic solid solution is formed. XPS analysis revealed that Ce and Tb mainly existed in the form of Ce^4＋ and Tb^3 ＋ , and Zr existed in the form of Zr^4＋ on the surface of the samples. The doped samples were homogenous in composition ; the introduction of Tb into the CeO2-ZrO2 promoters resuited in the formation of a solid solution, and the concentration of surface lattice oxygen was increased.展开更多
基金Project supported by the National Natural Science Foundation of China(Nos.11988102,91848201,11872004,and 11802004)
文摘In this study,we numerically investigate the droplet impact onto a thin liquid film deposited on a structured surface with square pillars and cavities.The time evolution of crown geometry is strongly affected by the surface structure.When the thickness of the liquid film is larger than the structure height,the expanding speed of the crown base radius is independent of the structure width.However,if the liquid film thickness is equal to the structure height,the crown base expands slower as the structure width increases.Surface structures have strong effects on the crown height and radius,and can prevent ejected filament from breaking into satellite droplets for certain cases.For the liquid film with the thickness equal to the pillar height,both the crown height and the radius exhibit non-monotonic behaviors as the pillar width increases.There exists one pillar width which produces the smallest crown height and the largest crown radius.
文摘This paper proposes an investigation of the effects of laser engineering surface with dimple operating under lubrication. Dimples with semi-spherical geometry, with 100 μm in diameter and 25 μm in depth, were Laser-machined on the surfaces of high speed steel AISI H 13 discs, with three different distribution densities applied over the surface. Pin-on-disc experiments were performed by using counter bodies made with AISI 440C and Tungsten carbide ISO K20 pins. The experiments provided data information on the influence of dimple distribution on the coefficient of friction. Numerical simulations were performed to understand the influence of the pin and disc surface roughness on the contact problem. The results suggest that the design of dimple-structured surfaces rely on nine main parameters： material contact pair and its respective hardness, Young Modulus, the roughness of the surfaces, the dimple design, the dimple distribution, the load applied, the velocity and the type of lubricant. A better performance can be obtained from a compromise solution over these parameters, and the dimple concentration has a dominance over the other parameters. The best results were obtained with a lower concentration of dimples, under higher speed and load. Numerical simulations can also be used as a design tool, supporting decisions regarding shape and distribution of the dimples and material selections for the contact pair.
基金supported by the National Natural Science Foundation of China(Grant No.51336003)the 333 Scientific Research Project of Jiangsu Province(Grant No.BRA2011134)
文摘Nanostructured surface is a promising photon management strategy to tune spectrum in design of the selective solar absorber.In this paper,we propose a nanocone structured surface as a perfect solar absorber in application of the solar thermoelectric generators(STEGs).The trade-off between the solar absorption and the mid-infrared emission is obtained to maximize the STEG efficiency.The effects of the geometric parameters,thermal concentration,incident angle and polarized state as well as the lattice arrangement are systematically investigated.The results show that the STEGs equipped with our proposed selective solar absorber can achieve a peak efficiency of 6.53%under AM1.5G condition(no optical concentration).Furthermore,the selective solar absorber exhibits insensitive behavior to the incident angle and polarization angle as well.This means that the proposed selective solar absorber can utilize solar energy as much as possible and be generally suitable in equipping the STEGs without optical concentration.
基金National Natural Science Foundation of China (grant nos.62134009,62121005)the Innovation Grant of Changchun Institute of Optics,Fine Mechanics and Physics (CIOMP),Jilin Provincial Science and Technology Development Project (grant no:YDZJ202102CXJD002)Bill&Melinda Gates Foundation (grant no:OPP1157723)
文摘Electrochemical oxidation/reduction of radicals is a green and environmentally friendly approach to generating fuels.These reactions,however,suffer from sluggish kinetics due to a low local concentration of radicals around the electrocatalyst.A large applied electrode potential can enhance the fuel generation efficiency via enhancing the radical concentration around the electrocatalyst sites,but this comes at the cost of electricity.Here,we report about a~45%saving in energy to achieve an electrochemical hydrogen generation rate of 3×10^(16) molecules cm^(–2)s^(–1)(current density:10 mA/cm^(2))through localized electric field-induced enhancement in the reagent concentration(LEFIRC)at laser-induced periodic surface structured(LIPSS)electrodes.The finite element model is used to simulate the spatial distribution of the electric field to understand the effects of LIPSS geometric parameters in field localization.When the LIPSS patterned electrodes are used as substrates to support Pt/C and RuO_(2) electrocatalysts,the η_(10) overpotentials for HER and OER are decreased by 40.4 and 25%,respectively.Moreover,the capability of the LIPSS-patterned electrodes to operate at significantly reduced energy is also demonstrated in a range of electrolytes,including alkaline,acidic,neutral,and seawater.Importantly,when two LIPSS patterned electrodes were assembled as the anode and cathode into a cell,it requires 330 mVs of lower electric potential with enhanced stability over a similar cell made of pristine electrodes to drive a current density of 10 mA/cm^(2).This work demonstrates a physical and versatile approach of electrode surface patterning to boost electrocatalytic fuel generation performance and can be applied to any metal and semiconductor catalysts for a range of electrochemical reactions.
基金supported by the Innovative Research Group Project of the National Natural Science Foundation of China(T2121004)Key Programme(52235007)National Outstanding Youth Foundation of China(52325504).
文摘Hydrogel scaffolds have numerous potential applications in the tissue engineering field.However,tough hydrogel scaffolds implanted in vivo are seldom reported because it is difficult to balance biocompatibility and high mechanical properties.Inspired by Chinese ramen,we propose a universal fabricating method(printing-P,training-T,cross-linking-C,PTC&PCT)for tough hydrogel scaffolds to fill this gap.First,3D printing fabricates a hydrogel scaffold with desired structures(P).Then,the scaffold could have extraordinarily high mechanical properties and functional surface structure by cycle mechanical training with salting-out assistance(T).Finally,the training results are fixed by photo-cross-linking processing(C).The tough gelatin hydrogel scaffolds exhibit excellent tensile strength of 6.66 MPa(622-fold untreated)and have excellent biocompatibility.Furthermore,this scaffold possesses functional surface structures from nanometer to micron to millimeter,which can efficiently induce directional cell growth.Interestingly,this strategy can produce bionic human tissue with mechanical properties of 10 kPa-10 MPa by changing the type of salt,and many hydrogels,such as gelatin and silk,could be improved with PTC or PCT strategies.Animal experiments show that this scaffold can effectively promote the new generation of muscle fibers,blood vessels,and nerves within 4 weeks,prompting the rapid regeneration of large-volume muscle loss injuries.
文摘This paper discusses the coloration process on the stainless steel and the properties of the film. The compositions, morphology and structure of colored films on stainless steel are studied by using SEM,AES,AFM,STM. The diffusion controlled mechanisms of films and calculation formula of surface electropotential difference are discussed.
基金supported by the National Natural Science Foundation of China (U1609209)National Natural Science Foundation of China (61605162)+2 种基金NSFC-Liaoning Province united foundation (U1608259)National Natural Science Foundation of China (51501219)the financial support from the China Scholarship Council
文摘Paint removal from steel structure is executed for shipyards of marine and offshore engineering.Due to environmental unfriendliness and unhealthy drawbacks of sand blasting technique, laser ablation technique is proposed as a substituting method.By absorbing high energy of the 1064 nm pulsed laser, the paint is vaporized quickly.The ablated debris is then collected by using a suction pump.Initial metal surface of the steel is exposed when laser beam irradiates perpendicularly and scans over it.The cleaned surface fulfills the requirements of surface preparation standards ISO 8501 of SA2.The adhesion is further characterized with pull-off test after carrying out painting with Jotamastic 87 aluminum paint.The repainting can be embedded onto the laser cleaned surface to bond much more tightly.The excellent adhesion strength of 20 MPa between repainted coating and the substrate is achieved, which is higher than what is required by shipyards applications.
基金Project(51378457)supported by the National Natural Science Foundation of China
文摘An essential step for the realization of free-form surface structures is to create an efficient structural gird that satisfies not only the architectural aesthetics,but also the structural performance.Employing the main stress trajectories as the representation of force flows on a free-form surface,an automatic grid generation approach is proposed for the architectural design.The algorithm automatically plots the main stress trajectories on a 3D free-form surface,and adopts a modified advancing front meshing technique to generate the structural grid.Based on the proposed algorithm,an automatic grid generator named "St-Surmesh" is developed for the practical architectural design of free-form surface structure.The surface geometry of one of the Sun Valleys in Expo Axis for the Expo Shanghai 2010 is selected as a numerical example for validating the proposed approach.Comparative studies are performed to demonstrate how different structural grids affect the design of a free-form surface structure.
文摘Inhomogeneity and low efficiency are two important factors that limit the application of laser-induced periodic surface structures(LIPSSs),especially on glass surfaces.In this study,two-beam interference(TBI)of femtosecond lasers was used to produce large-area straight LIPSSs on fused silica using cylindrical lenses.Compared with those produced us-ing a single circular or cylindrical lens,the LIPSSs produced by TBI are much straighter and more regular.Depending on the laser fluence and scanning velocity,LIPSSs with grating-like or spaced LIPSSs are produced on the fused silica sur-face.Their structural colors are blue,green,and red,and only green and red,respectively.Grating-like LIPSS patterns oriented in different directions are obtained and exhibit bright and vivid colors,indicating potential applications in surface coloring and anti-counterfeiting logos.
文摘Biochars are known for their heterogeneity, especially in pore and surface structure associated with pyrolysis processes and sources of feedstocks. The surface area of biochar is likely to be an important determinant of the extent of soil microbial attachment, whereas the porous structure of biochar is expected to provide protection for soil microorganisms. Potential interactions between biochars from different sources and with different particle sizes were investigated in relation to soil microbial properties in a short-term incubation study. Three particle size （sieved） fractions （0.5-1.0, 1.0-2.0 and 2.0-4.0 mm） from three woody biochars produced from jarrah wood, jarrah and wandoo wood and Australian wattle branches, respectively, were incubated in soil at 25 ℃ for 56 d. Observation by scanning electron microscopy （SEM） and characterisation of pore and surface area showed that all three woody biochars provided potential habitats for soil microorganisms due to their high porosity and surface areas. The biochars were structurally heterogeneous, varying in porosity and surface structure both within and between the biochar sources. After the 56-d incubation, hyphal colonisation was observed on biochar surfaces and in larger biochar pores. Soil clumping occurred on biochar particles, cementing and covering exposed biochar pores. This may have altered surface area and pore availability for microbial colonisation. Transient changes in soil microbial biomass, without a consistent trend, were observed among biochars during the 56-d incubation.
基金co-supported by the Key-Area Research and Development Program of Guangdong Province(No.2018B090906002)the National Natural Science Foundation of China(No.51875574)the National Science and Technology Major Project of China(No.2017-Ⅶ-0003-0096-1)。
文摘Titanium alloys have a wide application in aerospace industries as it has greater strength and low density, but it has poor tribological properties. To improve its friction and wear performance, in present work, a femtosecond laser is used to directly irradiate the Ti6Al4V titanium alloy surface in air conditioning, which results in localized ablation and the formation of periodic microstructures but also a strong pressure wave, propagating the material inside. Through the optimization of processing parameters, surface modification and periodic micropatterning with effective anti-friction properties were successfully induced on the surface. After a treatment of femtosecond laser-induced surface modification(FsLSM), the surface microhardness was improved by 16.6% and compressive residual stress reached-746 MPa. Besides, laser-induced periodic surface structures(LIPSS) with a titanium oxide outer coating were fabricated uniformly on the titanium alloy surface. Rotary ball-on-disk wear experiments revealed that the average coefficient of friction(COF) and wear mass loss of the specimen with Fs LSM treatment were largely reduced by 68.9% and 90% as compared to that of untreated specimens, respectively. It was analyzed that the reason for the remarkable wear resistance was attributed to the comprehensive action of the generation of LIPSS, the titanium oxide outer coating, high amplitude compressive residual stress and gradient grain size distribution on the subsurface during the laser surface treatment. Since the findings here are broadly applicable to a wide spectrum of engineering metals and alloys, the present results offer unique pathways to enhancing the tribological performance of materials.
基金supported by MEXT Quantum Leap Flagship Program(MEXT Q-LEAP)Grant Number JPMXS0118067246.
文摘Femtosecond laser pulses with GHz burst mode that consist of a series of trains of ultrashort laser pulses with a pulse interval of several hundred picoseconds offer distinct features in material processing that cannot be obtained by the conventional irradiation scheme of femtosecond laser pulses(single-pulse mode).However,most studies using the GHz burst mode femtosecond laser pulses focus on ablation of materials to achieve high-efficiency and high-quality material removal.In this study,we explore the ability of the GHz burst mode femtosecond laser processing to form laser-induced periodic surface structures(LIPSS)on silicon.It is well known that the direction of LIPSS formed by the single-pulse mode with linearly polarized laser pulses is typically perpendicular to the laser polarization direction.In contrast,we find that the GHz burst mode femtosecond laser(wavelength:1030 nm,intra-pulse duration:220 fs,intra-pulse interval time(intra-pulse repetition rate):205 ps(4.88 GHz),burst pulse repetition rate:200 kHz)creates unique two-dimensional(2D)LIPSS.We regard the formation mechanism of 2D LIPSS as the synergetic contribution of the electromagnetic mechanism and the hydrodynamic mechanism.Specifically,generation of hot spots with highly enhanced electric fields by the localized surface plasmon resonance of subsequent pulses in the bursts within the nanogrooves of one-dimensional LIPSS formed by the preceding pulses creates 2D LIPSS.Additionally,hydrodynamic instability including convection flow determines the final structure of 2D LIPSS.
基金the financial supported by the National Natural Science Foundation of China(No.11602069 and No.51779056)the Natural Science Foundation of Heilonjiang Province(No.E2017026).
文摘The shock wave of the underwater explosion can cause severe damage to the ship structure.The propagation characteristics of shock waves near the structure surface are complex,involving lots of complex phenomena such as reflection,transmission,diffraction,and cavitation.However,different structure surface boundaries have a significant effect on the propagation characteristics of pressure.This paper focuses on investigating the behavior of shock wave propagation and cavitation from underwater explosions near various structure surfaces.A coupled Runge–Kutta discontinuous Galerkin(RKDG)and finite elementmethod(FEM)is utilized to solve the problem of the complex waves of fluids and structure dynamic response,considering the fluid compressibility.The level set(LS)method and the ghost fluid(GF)method are combined to capture the moving interface and deal with the stability of the coupling between the shock wave and structure surface.Besides,a cut-off cavitation model is introduced to the RKDG method.The validation of the numerical calculation model is discussed by comparing it with the known solution to verify the numerical solutions.Then,crucial kinds of structure surface boundary conditions include shallow-water single layer elasticity plate,double-layer crevasse elasticity plate,single layer curved elasticity plate,and double-layer curved elasticity plates are analyzed and discussed.The results and analysis can provide references for underwater explosion pressure characteristics,the impacting response of different boundary structures,and designing structures.
基金Supported by National Natural Science Foundation of China(Grant No.51422507)Hubei Provincial Natural Science Foundation of China(Grant No.2015CFB372)+1 种基金Fundamental Research Funds for the Central Universities of China(Grant No.2015IVA010)Tribology Science Fund of State Key Laboratory of Tribology of China(Grant No.SKLTKF14B03)
文摘It is of a vital importance to reduce the frictional losses in marine diesel engines. Advanced surface textures have provided an e ective solution to friction performance of rubbing pairs due to the rapid development of surface engineering techniques. However,the mechanisms through which textured patterns and texturing methods prove beneficial remains unclear. To address this issue,the tribological system of the cylinder liner?piston ring(CLPR) is investigated in this work. Two types of surface textures(Micro concave,Micro V?groove) are processed on the cylinder specimen using di erent processing methods. Comparative study on the friction coe cients,worn surface texture features and oil film characteristics are performed. The results demonstrate that the processing method of surface texture a ect the performance of the CLPR pairs under the specific testing conditions. In addition the micro V?groove processed by CNCPM is more favorable for improving the wear performances at the low load,while the micro?con?cave processed by CE is more favorable for improving the wear performances at the high load. These findings are in helping to understand the e ect of surface texture on wear performance of CLPR.
文摘Ball burnishing is a plastic deformation process used as a surface smoothing and surface improvement finishing treatment after turning or milling processes. This process changes the surface stereometrics of the previously machining surface. Burnishing with hydrostatic tools can be easily and effectively used on both conventional and Computer Numeric Control(CNC) machines. The existing research of the burnishing process mainly focuses on the functional surface characterization, for example, surface roughness, wear resistance, surface layer hardness, etc. There is a lack of references reporting a detailed analysis of 3D parameters calculation with a mathematical model to evaluate the results of the ball burnishing. This paper presents the effect of ball burnishing process parameters with hydrostatic tools on the resulting surface structure geometry. The surface topography parameters were calculated using the Taly Map software. Studies were conducted based on Hartley’s static, determined plan. Such a plan can be built on a hypersphere or hypercube. In this work, a hypercube was used. In the case of Hartley’s plan makes it possible to define the regression equation in the form of a polynomial of the second degree. The input process parameters considered in this study include the burnishing rate, applied pressure, and line-to-line pitch. The significant influence of these parameters was confirmed and described as a mathematical power model. The results also showed a positive effect of hydrostatic burnishing on the roughness and geometric structure of the surface.
文摘The poor wear resistance and bio-inertness surface of polyetheretherketone(PEEK)limits the implant applications of PEEK and its composites.Carbon fiber(CFR)was used to boost the wear resistance of PEEK;however,the bioactivity of carbon fiber-reinforced polyetheretherketone(CFR-PEEK)composites is even worse.The bioactivity of CFR-PEEK can be enhanced by constructing 3D porous structure.Nevertheless,large number of sulfur component introduced by sulfonation shows cytotoxicity and can cause damage to human cells.Besides,the sulfur component affects the cytotoxicity and bioactivity of sulfonated CFR-PEEK(SCFR-PEEK).Hydrothermal treatment can sweep away the sulfur component in the 3D porous structure of SCFR-PEEK.Meanwhile,the changes in crystallinity and hardness after hydrothermal treatment may also affect the wear resistance.Therefore,the effect of hydrothermal temperature on wear resistance,cytotoxicity and bioactivity of SCFR-PEEK were studied.In this work,the samples with hydrothermal temperature 90–120℃exhibited high wear resistance.The 3D pore structure of SCFR-PEEK unchanged after hydrothermal treatment,and the sulfur component in the 3D pore structure gradually decreased with increasing hydrothermal temperature by SEM images and EDS analysis.In addition,SCFR-PEEK treated in 90–120℃.Exhibited low cytotoxicity and high bioactivity,which is beneficial for the implant materials.
基金the financial support provided by the National Natural Science Foundation of China(Nos.22072164,21773269,51932005 and 21761132025)the Liao Ning Revitalization Talents Program(No.XLYC1807175)。
文摘Selective hydrogenation of substituted nitroarenes is an important reaction to obtain amines.Supported metal catalysts are wildly used in this reaction because the surface structure of supports can tune the properties of the supported metal nanoparticles(NPs)and promote the selectivity to amines.Herein,Pt NPs were immobilized on Fe OOH,Fe_(3)O_(4)andα-Fe_2O_(3)nanorods to synthesize a series of iron compounds supported Pt catalysts by liquid phase reduction method.Chemoselective hydrogenation of 3-nitrostyrene to 3-aminostyrene was used as probe reaction to evaluate the performance of the catalysts.The results show that Pt/Fe OOH exhibits the highest selectivity and activity.Fe OOH support with pores and-OH groups can tune the electronic structure of Pt NPs.The positive charge of Pt NPs supported on Fe OOH is key factor for improving the catalytic performance.
基金National Natural Science Foundation of China(No.52173264).
文摘Surface structural engineering is desirable in modifying the surface performance of carbonyl iron powder(CIP)to enhance microwave absorption(MA)and anti-oxidation performance.Herein,the surface shape-dependent CIP absorbers are designed via surface coating with zinc oxide(ZnO)nanoparticles and then a thermal annealing treatment.The morphology of ZnO nanoparticles which can be easily regulated by controlling the annealing temperature ultimately affects the MA performance of CIP coating with ZnO nanoparticles(CIP@ZnO).The core-shell CIP@ZnO particles with cubic cone ZnO nanoparticles exhibit ex-cellent MA performance and thermal stability in comparison to the original CIP.Specifically,the CIP@ZnO annealed at 350 ℃(CIP@ZnO-350)samples which have the cubic cone ZnO nanoparticles exhibit a min-imum reflection loss(RLmin)of-55.35 dB at a thickness of 2.1 mm and a maximum effective absorp-tion bandwidth(EAB)of 7.09 GHz at a thickness of 2.0 mm.In addition,the antioxidant property of the CIP@ZnO composite particles is abruptly enhanced,which breaks the restriction of the application of CIP at high temperatures.The superior MA performance of CIP@ZnO particles with cubic cone ZnO nanoparti-cles comes from the enhancement in surface shape-dependent multiple microwave scattering,interfacial polarization,and electromagnetic-dielectric synergism between ZnO and CIP.
基金This study is partly supported by the following programs:National Natural Science Foundation of China(Grant No.52035012,51372210)the Basic Research Foundation Key Project of Sichuan Province(2021JY0046)Fundamental Research Funds for the Central Universities(2682020ZT91).
文摘The aim of this study was to reconstruct surface porous structure with hundreds of micrometers and then bio-mineralize Sr-doped Calcium Phosphate(Sr-doped CaP)on Polyetheretherketone(PEEK)profile to enhance its bioactivity.A surface porous structure was prepared on PEEK profile by embedding and acid-etching of SiO2 particles as porogen(SP-PEEK).Then the Sr-doped CaP was further decorated on the porous surface after sulfonation,introduction of Sr-doped CaP crystal seeds and bio-mineralization in 1.5 times simulated body fluid(BSSP-PEEK-CaP/Sr).It was feasible to reconstruct the surface porous structure with hundreds of micrometers on PEEK profile by the present method without damaging its mechanical properties.The Sr-doped CaP crystal seeds effectively promoted the bio-mineralization of bio-inertness PEEK.All as-prepared PEEK did not inhibit the proliferation of cells.ALP of bio-mineralized groups was significantly increased than that of the other groups.The BSSP-PEEK-CaP/Sr obviously affected the morphology and promoted the adhesion and spreading of cells.As a result,the cyto-biocompatibity and bioactivity of PEEK were improved after bio-mineralization.Sr-doped CaP on PEEK most likely was beneficial for cells,which was associated with the increasing of the hydrophilicity on PEEK.This study provided a candidate method to improve the osteogenesis of PEEK implants.
基金Project supported by the Natural Science Basic Research Plan in Shaanxi Province of China (2004B13)
文摘The three-way catalysts （TWCs） promoters Ce0.6Zr0.4- x TbxO2-y were prepared by sol-gel method. BET surface areas analysis indicated that an increase of the dopant Tb content from x = 0.05 to x = 0.15 favors an increase of surface area from 66.8 to 80.4 m^2· g^-1 compared with the undoped sample Ce0 .6oZr0.40O2 65.1 m^2·g^- 1 after calcination at 650℃. Transmission electron microscopy （TEM） observation indicated that the doped samples have a higher thermal stability. The XRD and Raman spectra confirmed that the Ce0.6Zr0.4-xTbxO2-y cubic solid solution is formed. XPS analysis revealed that Ce and Tb mainly existed in the form of Ce^4＋ and Tb^3 ＋ , and Zr existed in the form of Zr^4＋ on the surface of the samples. The doped samples were homogenous in composition ; the introduction of Tb into the CeO2-ZrO2 promoters resuited in the formation of a solid solution, and the concentration of surface lattice oxygen was increased.
