On the basis of discussing the influencing mode of plant moisture stress on plant physiological process and the division of soil moisture availability range, the water suction values partitioning soil moisture were pu...On the basis of discussing the influencing mode of plant moisture stress on plant physiological process and the division of soil moisture availability range, the water suction values partitioning soil moisture were put forward, and then the corresponding water moistures under water stress were obtained by conversing together with characteristic curve of water moisture.展开更多
Laminated carbon fiber clothes were infiltrated to prepare carbon fiber reinforced pyrolytic carbon （C/C） using isothermal chemical vapor infiltration （CVI）. The bending fatigue behavior of the infiltrated C/C com...Laminated carbon fiber clothes were infiltrated to prepare carbon fiber reinforced pyrolytic carbon （C/C） using isothermal chemical vapor infiltration （CVI）. The bending fatigue behavior of the infiltrated C/C composites was tested under two different stress levels. The residual strength and modulus of all fatigued samples were tested to investigate the effect of maximum stress level on fatigue behavior of C/C composites. The microstructure and damage mechanism were also investigated. The results showed that the residual strength and modulus of fatigued samples were improved. High stress level is more effective to increase the modulus. And for the increase of flexural strength, high stress level is more effective only in low cycles. The fatigue loading weakens the bonding between the matrix and fiber, and then affects the damage propagation pathway, and increases the energy consumption. So the properties of C/C composites are improved.展开更多
Rock mass large deformation in underground powerhouse caverns has been a severe hazard in hydropower engineering in Southwest China.During the development of rock mass large deformation,a sequence of fractures was gen...Rock mass large deformation in underground powerhouse caverns has been a severe hazard in hydropower engineering in Southwest China.During the development of rock mass large deformation,a sequence of fractures was generated that can be monitored using microseismic(MS)monitoring techniques.Two MS monitoring systems were established in two typical underground powerhouse caverns featuring distinct geostress levels.The MS b-values associated with rock mass large deformation and their temporal variation are analysed.The results showed that the MS bvalue in course of rock mass deformation was less than 1.0 in the underground powerhouse caverns at a high stress level while larger than 1.5 at a low stress level.Prior to the rock mass deformation,the MS b-values derived from both the high-stress and low-stress underground powerhouse caverns show an incremental decrease over 10%within 10 d.The results contribute to understanding the fracturing characteristics of MS sources associated with rock mass large deformation and provide a reference for early warning of rock mass large deformation in underground powerhouse caverns.展开更多
The abundant data of focal mechanism solutions in Tangshan region, China, are inverted for the tectonic stress field. Combined with tectonophysical consideration, the magnitude of the three principal stresses, as well...The abundant data of focal mechanism solutions in Tangshan region, China, are inverted for the tectonic stress field. Combined with tectonophysical consideration, the magnitude of the three principal stresses, as well as their vertical variation under the average crustal rock property, in the source region of the 1976 Tangshan earthquake is estimated. The relationship between crustal stress and friction mc, pore pressure P0 and stress shape factor F is studied. The paper draws the conclusion that the vertical increasing rate of the maximum principal stress s is directly proportional to friction, and inversely to pore pressure P0 and stress shape factor F ; while the vertical increasing rate of the minimum principal tress s is directly proportional to pore pressure P0, inversely to friction mc and stress shape factor F. This study is a try to invert the data of focal mechanism solutions for the complete stress tensor.展开更多
BACKGROUND The incidence of chronic wounds is rising due to an aging population and lifestyle changes in our country.In addition,as the disease spectrum evolves,chronic wounds have become common clinical issues that s...BACKGROUND The incidence of chronic wounds is rising due to an aging population and lifestyle changes in our country.In addition,as the disease spectrum evolves,chronic wounds have become common clinical issues that seriously threaten health and impose significant social and economic burdens.AIM To investigate how depression,anxiety,peripheral blood inflammatory factors,and stress levels affect therapeutic outcomes in patients with chronic wounds.METHODS Retrospectively collected clinical data from 110 patients with chronic wounds treated at Changde Hospital,Xiangya School of Medicine,Central South University(The First People’s Hospital of Changde City)between January 2021 and December 2023,categorizing them into effective and ineffective groups based on treatment effects.Differences between both groups were analyzed using univariate analysis,independent risk factors identified via logistic regression,and their predictive value assessed through receiver operating characteristic analysis.RESULTS Following treatment,95 cases were classified as the effective group(cured or improved),while 15 cases with improvement formed the ineffective group.Significant differences between both groups were noted in wound area,infection status,daily bed time,Hamilton Anxiety Rating Scale(HAMA)scores,Hamilton Depression Rating Scale(HAMD)scores,and levels of interleukin-6,tumor necrosis factor-alpha,and superoxide dismutase(P<0.05).Logistic regression analysis identified a wound area≥7 cm^(2),HAMA≥9 scores,and HAMD≥8 scores were independent risk factors for ineffective treatment in patients with chronic wounds(P<0.05).The receiver operating characteristic curve analysis revealed that the area under the curve for ineffective treatment based on wound area,HAMA,and HAMD was 0.767,0.805,and 0.768 respectively.CONCLUSION Wound size,anxiety,and depression are significant factors influencing the therapeutic outcomes in patients with chronic wounds that require careful attention,alongside the development of appropriate strategies.展开更多
To obtain the stress level at the earthquake source, this paper sets forth the solution of the stress magnitude at the earthquake source by seismic stress drop and the stress axis deflections before and after large ea...To obtain the stress level at the earthquake source, this paper sets forth the solution of the stress magnitude at the earthquake source by seismic stress drop and the stress axis deflections before and after large earthquakes. The pre-seismic and post-seismic stress direction can be statistically determined by a large collection of foreshock and aftershock focal mechanism data while the stress drop can be determined through the source fracture inversion from seismic wave data or crust deformation data. The paper attempts to make a fundamental contribution to seismic dynamics.展开更多
A method estimating the stress level in the focal region of an earthquake is proposed here. Taking the 2001 M=8.1 Western Kunlun Mountain Pass earthquake as an example, we estimate its stress level in the focal region...A method estimating the stress level in the focal region of an earthquake is proposed here. Taking the 2001 M=8.1 Western Kunlun Mountain Pass earthquake as an example, we estimate its stress level in the focal region before and after it by this method. The results show that the stress level in the focal region just prior to the initiation of this event is approximately 6.3-8 MPa, and about 5-6.7 MPa remained in the focal region after its occurrence. The stress in the focal region decreased by roughly twenty percent after this event.展开更多
Fracture(fault)reactivation can lead to dynamic geological hazards including earthquakes,rock collapses,landslides,and rock bursts.True triaxial compression tests were conducted to analyze the fracture reactivation pr...Fracture(fault)reactivation can lead to dynamic geological hazards including earthquakes,rock collapses,landslides,and rock bursts.True triaxial compression tests were conducted to analyze the fracture reactivation process under two different orientations of σ_(2),i.e.σ_(2) parallel to the fracture plane(Scheme 2)and σ_(2) cutting through the fracture plane(Scheme 3),under varying σ_(3) from 10 MPa to 40 MPa.The peak or fracture reactivation strength,deformation,failure mode,and post-peak mechanical behavior of intact(Scheme 1)and pre-fractured(Schemes 2 and 3)specimens were also compared.Results show that for intact specimens,the stress remains nearly constant in the residual sliding stage with no stick-slip,and the newly formed fracture surface only propagates along the σ_(2) direction when σ_(3) ranges from 10 MPa to 30 MPa,while it extends along both σ_(2) and σ_(3) directions when σ_(3) increases to 40 MPa;for the pre-fractured specimens,the fractures are usually reactivated under all the σ_(3) levels in Scheme 2,but fracture reactivation only occurs when σ_(3) is greater than 25 MPa in Scheme 3,below which new faulting traversing the original macro fracture occurs.In all the test schemes,both ε_(2) and ε_(3) experience an accumulative process of elongation,after which an abrupt change occurs at the point of the final failure;the degree of this change is dependent on the orientation of the new faulting or the slip direction of the original fracture,and it is generally more than 10 times larger in the slip direction of the original fracture than in the non-slip direction.Besides,the differential stress(peak stress)required for reactivation and the post-peak stress drop increase with increasing σ_(3).Post-peak stress drop and residual strength in Scheme 3 are generally greater than those in Scheme 2 at the same σ_(3) value.Our study clearly shows that intermediate principal stress orientation not only affects the fracture reactivation strength but also influences the slip deformation and failure modes.These new findings facilitate the mitigation of dynamic geological hazards associated with fracture and fault slip.展开更多
Leveling process plays an important role in delivering the desired material properties and product standards.An analytical method for the rotational leveling process of bars was presented.First,each cross section of t...Leveling process plays an important role in delivering the desired material properties and product standards.An analytical method for the rotational leveling process of bars was presented.First,each cross section of the bar in the leveling area was discretized with the roller gap-curvature relations established in both planes XYand XZ.Second,a numerical procedure with two steps was developed to simulate both pressing and leveling processes.This approach can be easily implemented to produce simulation results of the curvature and trajectory distributions during the leveling process,as well as the bending and residual stresses.It is found that curvature and trajectory distributions follow a sine-shape due to the characteristic of rotational movement,which also results in a helical pattern of residual stress after leveling.Based on the results obtained,it is also observed that the rotational movement is beneficial for adding the number of bending cycle.This is the reason why there are only a few pairs of rollers on the bar leveler.展开更多
For non-directional drilling cores,selection of samples and the test methods for in situ stress measurements to evaluate the Kaiser effect(KE)were proposed,and the magnitude and direction of the principal stresses wer...For non-directional drilling cores,selection of samples and the test methods for in situ stress measurements to evaluate the Kaiser effect(KE)were proposed,and the magnitude and direction of the principal stresses were derived from first principles.Based on this approach,the KE for 423 samples in the Burtai and Baode coal mines in the northern Ordos Basin(NOB),China,have been investigated.The results show that the maximum horizontal principal stress(σ_(H)),the minimum horizontal principal stress(σ_(h))and the vertical stress(σ_(v))varied with depth and location,and the values increase with increasing depth.Generally,the horizontal stresses play a leading role.For the main stress regimes in the NOB,σ_(H)>σ_(h)>σ_(v)(Burtai Mine,<172 m;Baode Mine,<170 m)andσ_(H)>σ_(v)>σ_(h)(Burtai Mine,170-800 m;Baode Mine,170-400 m),and theσ_(v)>σ_(H)>σ_(h)stress regimes are mainly distributed in moderately deep to deep coal mines.For rock masses with a depth of 350 m,k((σ_(H)+σ_(h))/2σ_(v))tends to 1,indicating that a deep critical state will gradually emerge.The test results are compared with those for the overcoring(OC)method,the anelastic strain recovery(ASR)method and micro-hydraulic fracturing(HF).The relative errors forσ_(H),σ_(h)andσ_(v)were 14.90%,19.67%,15.47%(Burtai Mine)and 10.74%,22.76%,19.97%(Baode Mine),respectively,and the errors are all within an acceptable range,thus verifying the reliability of the KE method.The dominant orientation for theσ_(H)(Burtai mine,NE-NNE;Baode Mine,NEE)is obtained via paleomagnetic technology,and the data are consistent with those(NE-NEE)of the earthquake focal mechanism solutions for the area.Based on the Byerlee-Anderson theory,a discussion is given on the levels of stress accumulation in the rock mass of the mines.For dry rocks or hydrostatic pressure rocks,the friction coefficients of the faults are low for both locations,and the values are less than the lower limit(0.6)of the strike-slip faults slip,indicating that the stress fractures at a low level around the study areas are lower than the friction limit stress.The stress accumulation levels in the Baode Mine are slightly larger than those in the Burtai Mine.展开更多
Water is a major limiting factor for food production and many countries fail to produce sufficient food for their population due to severe water scarcity （Jury and Vaux, 2005）. Rice is the main staple food worldwide...Water is a major limiting factor for food production and many countries fail to produce sufficient food for their population due to severe water scarcity （Jury and Vaux, 2005）. Rice is the main staple food worldwide. More than 50% of rice in the world is rain-fed and drought causes severe reduction in rice grain yield in rain-fed environments （Venuprasad et al., 2007; Zhang, 2007; Sandhu et al., 2014）. Therefore, enhancing drought resistance （DR） of rice is important for food security. However, DR is a complex trait, which is controlled by a large number of loci with small effect and is also affected by different genetic background, genotype-by-environment interaction and other stresses such as heat （Hu and Xiong, 2014）.展开更多
Polyamines, putrescine (PUT), spermidine (SPD) and spermine (SPM) are implicated in plants’ responses under conditions of abiotic stress. Previous research in other crops has indicated that polyamines and changes in ...Polyamines, putrescine (PUT), spermidine (SPD) and spermine (SPM) are implicated in plants’ responses under conditions of abiotic stress. Previous research in other crops has indicated that polyamines and changes in their concentrations are associated with drought tolerance under conditions of water-deficit stress;however, no information exists on cotton (Gossypium hirsutum L.). Growth chamber experiments were conducted with two cotton cultivars differing in drought tolerance, ST5288B2F (drought-sensitive) and Siokra L23 (drought-tolerant) in order to investigate the distribution of free polyamines, the effect of water-deficit stress on the polyamine metabolism of cotton reproductive units and their subtending leaves as well as the possible relationship between polyamines and drought tolerance in cotton. Our results showed that cotton ovaries contained significantly higher levels of total free polyamines compared to their subtending leaves under both control and water stress conditions. Water-deficit stress significantly increased PUT concentrations in ST5288B2F, while SPM levels significantly decreased in Siokra L23. The results indicated that water-deficit stress significantly affected cotton polyamine metabolism in reproductive structures and their subtending leaves;however, no clear relationship between drought-tolerance and changes in polyamine accumulation was established. Further research is needed to elucidate the mechanism according to which water-deficit stress affects polyamine metabolism.展开更多
The flatness of leveled plate is settled by residual stress. According to stress distribution simulated by FEM software ANSYS/LS-DYNA, the plate can be divided into non-steady region and steady region. The nonsteady r...The flatness of leveled plate is settled by residual stress. According to stress distribution simulated by FEM software ANSYS/LS-DYNA, the plate can be divided into non-steady region and steady region. The nonsteady region is composed of four zones, two of which are about half of leveling roller pitch at leading and end edges and other two are about 10% of the width at lateral edges. The steady region is the rest part enclosed by the non-steady regions. It is helpful to improve the leveling process by analyzing forming mechanism of each region and selecting suitable processes settings.展开更多
We studied the relationship between endogenous ABA and resistance to temperature stress in seedlings of hybrid rice. The hybrid rice Combinations Shanyou 63, Shanyou 287, Weiyou 63, and Weiyou 287 were treated under 2...We studied the relationship between endogenous ABA and resistance to temperature stress in seedlings of hybrid rice. The hybrid rice Combinations Shanyou 63, Shanyou 287, Weiyou 63, and Weiyou 287 were treated under 2℃ and 42℃ respectively for 48 h. Endogenous ABA concentrations were obtained by gas chromatography with electron capture detector (GC-ECD) and a nickel labelled external standard. Leakage of electrolytes were determined. At optimal temperature (27℃), there was difference between the level of endogenous ABA and the leakage of electrolytes in hybrid rice combinations, which attributed to genetic difference. ABA level in Weiyou system was higher than that in Shanyou, and there were distinctions between Shanyou system itself (see table). At 2℃, the ABA content of rice seedling was increased. ABA level of Weiyou system maintained higher than Shanyou system at 27℃. The leakage quantities of展开更多
The occurrence of geological hazards and the instability of geotechnical engineering structures are closely related to the time-dependent behavior of rock.However,the idealization boundary condition for constant stres...The occurrence of geological hazards and the instability of geotechnical engineering structures are closely related to the time-dependent behavior of rock.However,the idealization boundary condition for constant stress in creep or constant strain in relaxation is not usually attained in natural geological systems.Therefore,generalized relaxation tests that explore the simultaneous changes of stress and strain with time under different stress levels with constant pore-water pressure are conducted in this study.The results show that in area Ⅰ,area Ⅱ,and area Ⅲ,the stress and strain both change synchronously with time and show similar evolutionary laws as the strain-time curve for creep or the stress-time curve for relaxation.When the applied stress level surpasses the δ_(ci) or δ_(cd) threshold,the variations in stress and strain and their respective rates of change exhibit a significant increase.The radial deformation and its rate of change exhibit greater sensitivity in response to stress levels.The apparent strain deforms homogeneously at the primary stage,and subsequently,gradually localizes due to the microcrack development at the secondary stage.Ultimately,interconnection of the microcracks causes the formation of a shear-localization zone at the tertiary stage.The strain-time responses inside and outside the localization zone are characterized by local strain accumulation and inelastic unloading during the secondary and tertiary stages,respectively.The width of the shear-localization zone is found to range from 4.43 mm to 7.08 mm and increased with a longer time-to-failure.Scanning electron microscopy(SEM)reveals a dominant coalescence of intergranular cracks on the fracture surface,and the degree of physiochemical deterioration caused by water-rock interaction is more severe under a longer lifetime.The brittle sandstone’s time-dependent deformation is essentially controlled by microcrack development during generalized relaxation,and its expectancy-life is determined by its initial microstructural state and the rheological path.展开更多
文摘On the basis of discussing the influencing mode of plant moisture stress on plant physiological process and the division of soil moisture availability range, the water suction values partitioning soil moisture were put forward, and then the corresponding water moistures under water stress were obtained by conversing together with characteristic curve of water moisture.
基金Projects(50832004,51105132)supported by the National Natural Science Foundation of ChinaProject(B08040)supported by Program of Introducing Talents of Discipline to Universities,China
文摘Laminated carbon fiber clothes were infiltrated to prepare carbon fiber reinforced pyrolytic carbon （C/C） using isothermal chemical vapor infiltration （CVI）. The bending fatigue behavior of the infiltrated C/C composites was tested under two different stress levels. The residual strength and modulus of all fatigued samples were tested to investigate the effect of maximum stress level on fatigue behavior of C/C composites. The microstructure and damage mechanism were also investigated. The results showed that the residual strength and modulus of fatigued samples were improved. High stress level is more effective to increase the modulus. And for the increase of flexural strength, high stress level is more effective only in low cycles. The fatigue loading weakens the bonding between the matrix and fiber, and then affects the damage propagation pathway, and increases the energy consumption. So the properties of C/C composites are improved.
基金Projects(51809221,51679158)supported by the National Natural Science Foundation of ChinaProject(KFJJ20-06M)supported by the State Key Laboratory of Explosion Science and Technology(Beijing Institute of Technology),China。
文摘Rock mass large deformation in underground powerhouse caverns has been a severe hazard in hydropower engineering in Southwest China.During the development of rock mass large deformation,a sequence of fractures was generated that can be monitored using microseismic(MS)monitoring techniques.Two MS monitoring systems were established in two typical underground powerhouse caverns featuring distinct geostress levels.The MS b-values associated with rock mass large deformation and their temporal variation are analysed.The results showed that the MS bvalue in course of rock mass deformation was less than 1.0 in the underground powerhouse caverns at a high stress level while larger than 1.5 at a low stress level.Prior to the rock mass deformation,the MS b-values derived from both the high-stress and low-stress underground powerhouse caverns show an incremental decrease over 10%within 10 d.The results contribute to understanding the fracturing characteristics of MS sources associated with rock mass large deformation and provide a reference for early warning of rock mass large deformation in underground powerhouse caverns.
基金The MOST under contract number 95-S-05 and Joint Seismological Science Foundation of China (199022).
文摘The abundant data of focal mechanism solutions in Tangshan region, China, are inverted for the tectonic stress field. Combined with tectonophysical consideration, the magnitude of the three principal stresses, as well as their vertical variation under the average crustal rock property, in the source region of the 1976 Tangshan earthquake is estimated. The relationship between crustal stress and friction mc, pore pressure P0 and stress shape factor F is studied. The paper draws the conclusion that the vertical increasing rate of the maximum principal stress s is directly proportional to friction, and inversely to pore pressure P0 and stress shape factor F ; while the vertical increasing rate of the minimum principal tress s is directly proportional to pore pressure P0, inversely to friction mc and stress shape factor F. This study is a try to invert the data of focal mechanism solutions for the complete stress tensor.
文摘BACKGROUND The incidence of chronic wounds is rising due to an aging population and lifestyle changes in our country.In addition,as the disease spectrum evolves,chronic wounds have become common clinical issues that seriously threaten health and impose significant social and economic burdens.AIM To investigate how depression,anxiety,peripheral blood inflammatory factors,and stress levels affect therapeutic outcomes in patients with chronic wounds.METHODS Retrospectively collected clinical data from 110 patients with chronic wounds treated at Changde Hospital,Xiangya School of Medicine,Central South University(The First People’s Hospital of Changde City)between January 2021 and December 2023,categorizing them into effective and ineffective groups based on treatment effects.Differences between both groups were analyzed using univariate analysis,independent risk factors identified via logistic regression,and their predictive value assessed through receiver operating characteristic analysis.RESULTS Following treatment,95 cases were classified as the effective group(cured or improved),while 15 cases with improvement formed the ineffective group.Significant differences between both groups were noted in wound area,infection status,daily bed time,Hamilton Anxiety Rating Scale(HAMA)scores,Hamilton Depression Rating Scale(HAMD)scores,and levels of interleukin-6,tumor necrosis factor-alpha,and superoxide dismutase(P<0.05).Logistic regression analysis identified a wound area≥7 cm^(2),HAMA≥9 scores,and HAMD≥8 scores were independent risk factors for ineffective treatment in patients with chronic wounds(P<0.05).The receiver operating characteristic curve analysis revealed that the area under the curve for ineffective treatment based on wound area,HAMA,and HAMD was 0.767,0.805,and 0.768 respectively.CONCLUSION Wound size,anxiety,and depression are significant factors influencing the therapeutic outcomes in patients with chronic wounds that require careful attention,alongside the development of appropriate strategies.
基金National Natural Science Foundation of China (40374012) and State Key Fundamental Research Development Plan Project (2001CB711005).
文摘To obtain the stress level at the earthquake source, this paper sets forth the solution of the stress magnitude at the earthquake source by seismic stress drop and the stress axis deflections before and after large earthquakes. The pre-seismic and post-seismic stress direction can be statistically determined by a large collection of foreshock and aftershock focal mechanism data while the stress drop can be determined through the source fracture inversion from seismic wave data or crust deformation data. The paper attempts to make a fundamental contribution to seismic dynamics.
文摘A method estimating the stress level in the focal region of an earthquake is proposed here. Taking the 2001 M=8.1 Western Kunlun Mountain Pass earthquake as an example, we estimate its stress level in the focal region before and after it by this method. The results show that the stress level in the focal region just prior to the initiation of this event is approximately 6.3-8 MPa, and about 5-6.7 MPa remained in the focal region after its occurrence. The stress in the focal region decreased by roughly twenty percent after this event.
基金funding support from the National Nature Science Foundation of China(Grant No.42272334)the National Key Research and Development Program of China(Grant No.2022YFE0137200)the Taishan Scholars Program(Grant No.2019RKB01083).
文摘Fracture(fault)reactivation can lead to dynamic geological hazards including earthquakes,rock collapses,landslides,and rock bursts.True triaxial compression tests were conducted to analyze the fracture reactivation process under two different orientations of σ_(2),i.e.σ_(2) parallel to the fracture plane(Scheme 2)and σ_(2) cutting through the fracture plane(Scheme 3),under varying σ_(3) from 10 MPa to 40 MPa.The peak or fracture reactivation strength,deformation,failure mode,and post-peak mechanical behavior of intact(Scheme 1)and pre-fractured(Schemes 2 and 3)specimens were also compared.Results show that for intact specimens,the stress remains nearly constant in the residual sliding stage with no stick-slip,and the newly formed fracture surface only propagates along the σ_(2) direction when σ_(3) ranges from 10 MPa to 30 MPa,while it extends along both σ_(2) and σ_(3) directions when σ_(3) increases to 40 MPa;for the pre-fractured specimens,the fractures are usually reactivated under all the σ_(3) levels in Scheme 2,but fracture reactivation only occurs when σ_(3) is greater than 25 MPa in Scheme 3,below which new faulting traversing the original macro fracture occurs.In all the test schemes,both ε_(2) and ε_(3) experience an accumulative process of elongation,after which an abrupt change occurs at the point of the final failure;the degree of this change is dependent on the orientation of the new faulting or the slip direction of the original fracture,and it is generally more than 10 times larger in the slip direction of the original fracture than in the non-slip direction.Besides,the differential stress(peak stress)required for reactivation and the post-peak stress drop increase with increasing σ_(3).Post-peak stress drop and residual strength in Scheme 3 are generally greater than those in Scheme 2 at the same σ_(3) value.Our study clearly shows that intermediate principal stress orientation not only affects the fracture reactivation strength but also influences the slip deformation and failure modes.These new findings facilitate the mitigation of dynamic geological hazards associated with fracture and fault slip.
文摘Leveling process plays an important role in delivering the desired material properties and product standards.An analytical method for the rotational leveling process of bars was presented.First,each cross section of the bar in the leveling area was discretized with the roller gap-curvature relations established in both planes XYand XZ.Second,a numerical procedure with two steps was developed to simulate both pressing and leveling processes.This approach can be easily implemented to produce simulation results of the curvature and trajectory distributions during the leveling process,as well as the bending and residual stresses.It is found that curvature and trajectory distributions follow a sine-shape due to the characteristic of rotational movement,which also results in a helical pattern of residual stress after leveling.Based on the results obtained,it is also observed that the rotational movement is beneficial for adding the number of bending cycle.This is the reason why there are only a few pairs of rollers on the bar leveler.
基金This study was supported by the Scientific and Technological Innovation Programs of Higher Education Institutions in Shanxi(2019L0772)the Key Research Development Program of Shanxi Province(201903D121070)+1 种基金the Key Research Development Program of Datong City in Shanxi Province(2019013)Shenhua Shendong Coal Branch Technology Innovation Project(HT2017-4307),and Ph.D.Research Startup of Shanxi Datong University.The authors especially thank Senior engineer Guijun Song,Erlin Wang and Guoqiang Xie of Shendong Coal Branch for their help in the on-site core collection and thank Professor Yixin Zhao for his assistance in drafting the paper.
文摘For non-directional drilling cores,selection of samples and the test methods for in situ stress measurements to evaluate the Kaiser effect(KE)were proposed,and the magnitude and direction of the principal stresses were derived from first principles.Based on this approach,the KE for 423 samples in the Burtai and Baode coal mines in the northern Ordos Basin(NOB),China,have been investigated.The results show that the maximum horizontal principal stress(σ_(H)),the minimum horizontal principal stress(σ_(h))and the vertical stress(σ_(v))varied with depth and location,and the values increase with increasing depth.Generally,the horizontal stresses play a leading role.For the main stress regimes in the NOB,σ_(H)>σ_(h)>σ_(v)(Burtai Mine,<172 m;Baode Mine,<170 m)andσ_(H)>σ_(v)>σ_(h)(Burtai Mine,170-800 m;Baode Mine,170-400 m),and theσ_(v)>σ_(H)>σ_(h)stress regimes are mainly distributed in moderately deep to deep coal mines.For rock masses with a depth of 350 m,k((σ_(H)+σ_(h))/2σ_(v))tends to 1,indicating that a deep critical state will gradually emerge.The test results are compared with those for the overcoring(OC)method,the anelastic strain recovery(ASR)method and micro-hydraulic fracturing(HF).The relative errors forσ_(H),σ_(h)andσ_(v)were 14.90%,19.67%,15.47%(Burtai Mine)and 10.74%,22.76%,19.97%(Baode Mine),respectively,and the errors are all within an acceptable range,thus verifying the reliability of the KE method.The dominant orientation for theσ_(H)(Burtai mine,NE-NNE;Baode Mine,NEE)is obtained via paleomagnetic technology,and the data are consistent with those(NE-NEE)of the earthquake focal mechanism solutions for the area.Based on the Byerlee-Anderson theory,a discussion is given on the levels of stress accumulation in the rock mass of the mines.For dry rocks or hydrostatic pressure rocks,the friction coefficients of the faults are low for both locations,and the values are less than the lower limit(0.6)of the strike-slip faults slip,indicating that the stress fractures at a low level around the study areas are lower than the friction limit stress.The stress accumulation levels in the Baode Mine are slightly larger than those in the Burtai Mine.
基金supported by grants from the National Program for Basic Research of China(No.2012CB114305)the National Program on High Technology Development(No. 2012AA10A303)the Oversea Graduate Program from Ministry of Education to K.Songyikhangsuthor
文摘Water is a major limiting factor for food production and many countries fail to produce sufficient food for their population due to severe water scarcity （Jury and Vaux, 2005）. Rice is the main staple food worldwide. More than 50% of rice in the world is rain-fed and drought causes severe reduction in rice grain yield in rain-fed environments （Venuprasad et al., 2007; Zhang, 2007; Sandhu et al., 2014）. Therefore, enhancing drought resistance （DR） of rice is important for food security. However, DR is a complex trait, which is controlled by a large number of loci with small effect and is also affected by different genetic background, genotype-by-environment interaction and other stresses such as heat （Hu and Xiong, 2014）.
文摘Polyamines, putrescine (PUT), spermidine (SPD) and spermine (SPM) are implicated in plants’ responses under conditions of abiotic stress. Previous research in other crops has indicated that polyamines and changes in their concentrations are associated with drought tolerance under conditions of water-deficit stress;however, no information exists on cotton (Gossypium hirsutum L.). Growth chamber experiments were conducted with two cotton cultivars differing in drought tolerance, ST5288B2F (drought-sensitive) and Siokra L23 (drought-tolerant) in order to investigate the distribution of free polyamines, the effect of water-deficit stress on the polyamine metabolism of cotton reproductive units and their subtending leaves as well as the possible relationship between polyamines and drought tolerance in cotton. Our results showed that cotton ovaries contained significantly higher levels of total free polyamines compared to their subtending leaves under both control and water stress conditions. Water-deficit stress significantly increased PUT concentrations in ST5288B2F, while SPM levels significantly decreased in Siokra L23. The results indicated that water-deficit stress significantly affected cotton polyamine metabolism in reproductive structures and their subtending leaves;however, no clear relationship between drought-tolerance and changes in polyamine accumulation was established. Further research is needed to elucidate the mechanism according to which water-deficit stress affects polyamine metabolism.
文摘The flatness of leveled plate is settled by residual stress. According to stress distribution simulated by FEM software ANSYS/LS-DYNA, the plate can be divided into non-steady region and steady region. The nonsteady region is composed of four zones, two of which are about half of leveling roller pitch at leading and end edges and other two are about 10% of the width at lateral edges. The steady region is the rest part enclosed by the non-steady regions. It is helpful to improve the leveling process by analyzing forming mechanism of each region and selecting suitable processes settings.
文摘We studied the relationship between endogenous ABA and resistance to temperature stress in seedlings of hybrid rice. The hybrid rice Combinations Shanyou 63, Shanyou 287, Weiyou 63, and Weiyou 287 were treated under 2℃ and 42℃ respectively for 48 h. Endogenous ABA concentrations were obtained by gas chromatography with electron capture detector (GC-ECD) and a nickel labelled external standard. Leakage of electrolytes were determined. At optimal temperature (27℃), there was difference between the level of endogenous ABA and the leakage of electrolytes in hybrid rice combinations, which attributed to genetic difference. ABA level in Weiyou system was higher than that in Shanyou, and there were distinctions between Shanyou system itself (see table). At 2℃, the ABA content of rice seedling was increased. ABA level of Weiyou system maintained higher than Shanyou system at 27℃. The leakage quantities of
基金financially supported by the National Natural Science Foundation of China(Grant Nos.52304099,52172625)Shenzhen Science and Technology Program(Grant No.RCYX20221008092903013).
文摘The occurrence of geological hazards and the instability of geotechnical engineering structures are closely related to the time-dependent behavior of rock.However,the idealization boundary condition for constant stress in creep or constant strain in relaxation is not usually attained in natural geological systems.Therefore,generalized relaxation tests that explore the simultaneous changes of stress and strain with time under different stress levels with constant pore-water pressure are conducted in this study.The results show that in area Ⅰ,area Ⅱ,and area Ⅲ,the stress and strain both change synchronously with time and show similar evolutionary laws as the strain-time curve for creep or the stress-time curve for relaxation.When the applied stress level surpasses the δ_(ci) or δ_(cd) threshold,the variations in stress and strain and their respective rates of change exhibit a significant increase.The radial deformation and its rate of change exhibit greater sensitivity in response to stress levels.The apparent strain deforms homogeneously at the primary stage,and subsequently,gradually localizes due to the microcrack development at the secondary stage.Ultimately,interconnection of the microcracks causes the formation of a shear-localization zone at the tertiary stage.The strain-time responses inside and outside the localization zone are characterized by local strain accumulation and inelastic unloading during the secondary and tertiary stages,respectively.The width of the shear-localization zone is found to range from 4.43 mm to 7.08 mm and increased with a longer time-to-failure.Scanning electron microscopy(SEM)reveals a dominant coalescence of intergranular cracks on the fracture surface,and the degree of physiochemical deterioration caused by water-rock interaction is more severe under a longer lifetime.The brittle sandstone’s time-dependent deformation is essentially controlled by microcrack development during generalized relaxation,and its expectancy-life is determined by its initial microstructural state and the rheological path.
