Low-density short-duration pulsed current-assisted aging treatment was applied to the Ti-6Al-4V-0.5Mo-0.5Zr alloy subjected to different solution treatments.The results show that numerous α_(p) phases redissolve into...Low-density short-duration pulsed current-assisted aging treatment was applied to the Ti-6Al-4V-0.5Mo-0.5Zr alloy subjected to different solution treatments.The results show that numerous α_(p) phases redissolve into the new β phase during the pulsed current-assisted aging process,and then the newly formed β phase is mainly transformed into the β_(t) phase,with occasional transition to new α_(p) phase,leading to a remarkable grain refinement,especially for the lamellarαs phases.In comparison to conventional aging treatment,the pulsed current-assisted aging approach achieves a significant enhancement in strength without degrading ductility,yielding an excellent mechanical property combination:a yield strength of 932 MPa,a tensile strength of 1042 MPa,and an elongation of 12.2%.It is primarily ascribed to the increased fraction of β_(t) phases,the obvious grain refinement effect,and the slip block effect induced by the multiple-variantαs colonies distributed within β_(t) phases.展开更多
In view of the phenomenon that the adhesion strength between the surface of polyacrylonitrile-butadiene-styrene-polycarbonate(ABS-PC)copolymer and the electroless copper plating layer is relatively low.To solve the pr...In view of the phenomenon that the adhesion strength between the surface of polyacrylonitrile-butadiene-styrene-polycarbonate(ABS-PC)copolymer and the electroless copper plating layer is relatively low.To solve the problems of poor surface wettability and low surface roughness of the ABS-PC substrate,the N,N-dimethylformamide(DMF)-ethanol(C_(2)H_(5)OH)-water(H_(2)O)system was employed as the swelling system for the ABS-PC substrate.The effects of the DMF volume fraction in the swelling system and the swelling time on the swelling effect of ABS-PC at 35℃ were investigated.KMnO_(4)-H_(2)SO_(4)-H_(2)O system was used as the etching system for ABS-PC substrate under the conditions of the volume ratio of water to sulfuric acid of 1﹕2,with KMnO_(4) content of 30 g/L,etching temperature of 60℃,and etching time of 25 min.The results indicate that dense pores with uniform sized are formed on the surface of the ABS-PC substrate surface after swelling and etching treatments,accompanied by an increase in surface roughness when the swelling temperature is 35℃,the DMF volume fraction in the swelling system is 80%,and the swelling time is 5 min.Furthermore,the content of C element on the surface of the ABS-PC substrate decreased,while that of O element increased,and the surface hydrophilicity is enhanced,which is attributed to two hydrophilic groups,-C=O and-COOH,being generated on the ABS-PC substrate surface,significantly improving the wettability of the ABS-PC substrate surface.Under the combination effects of high surface roughness and strong surface hydrophilicity,the adhesion strength between the ABS-PC substrate surface and the electroless copper plating layer reached to 0.81 kN/m,meeting the adhesion strength requirement of 0.70 kN/m in the industrial production.展开更多
We report a method for increasing the mechanical strength of carbon nanotube(CNT)fibers while enabling the uniform adhesion of cerium oxide(CeO_(2))abrasive particles to them using polyethyleneimine(PEI).Results show ...We report a method for increasing the mechanical strength of carbon nanotube(CNT)fibers while enabling the uniform adhesion of cerium oxide(CeO_(2))abrasive particles to them using polyethyleneimine(PEI).Results show that 5%of PEI increases the tensile strength of CNT fibers by approximately 175%.CeO_(2) particles were uniformly deposited on the reinforced CNT fibers by electrophoretic deposition.A flexible polishing tool was fabricated by weaving the CeO_(2)-CNT fibers into a non-woven fabric substrate.When used to polish potassium dihydrogen phosphate crystals,the tool reduced the surface roughness from 200 to 7.6 nm within 10 min.This approach has potential use for the development of new precision processing tools.展开更多
Chinese President Xi Jinping’s New Year message summarized an important year of steady progress as the country prepares to launch its 15th Five-Year Plan.“Our economic strength,scientific and technological abilities...Chinese President Xi Jinping’s New Year message summarized an important year of steady progress as the country prepares to launch its 15th Five-Year Plan.“Our economic strength,scientific and technological abilities,defense capabilities,and composite national strength all reached new heights.”declared President Xi Jinping in his 2026 New Year message on De-By CHINA TODAY cember 31,2025,offering a succinct summary of China’s development over the past year,marked by resilience,progress,and renewed confidence as the country stands at the threshold of a new development phase.展开更多
We report first-principles predictions of a cage-like polymeric nitrogen phase(cage-N)composed of interlocked N10 clusters stabilized by mixed sp^(2)/sp^(3) hybridization.Under high pressure,cage-N exhibits exceptiona...We report first-principles predictions of a cage-like polymeric nitrogen phase(cage-N)composed of interlocked N10 clusters stabilized by mixed sp^(2)/sp^(3) hybridization.Under high pressure,cage-N exhibits exceptional mechanical performance,including an ideal compressive strength of 343 GPa at a pressure of 300 GPa,~33% higher than that of diamond.This ultrahigh strength arises from the synergistic interplay between its three-dimensional covalent framework and hybridized bonding topology,which enables isotropic stress accommodation and dynamic electronic rearrangement.These results establish cage-N as a promising non-carbon ultrahard material and provide a bonding-driven route toward designing superhard frameworks under extreme conditions.展开更多
In this study,a facile method was employed to synthesize strong,yet highly elastic polyurethane-urea(PUU)with typical characteristics and 94% optical transmittance.Graphene platelets(GNPs)were prepared and modified vi...In this study,a facile method was employed to synthesize strong,yet highly elastic polyurethane-urea(PUU)with typical characteristics and 94% optical transmittance.Graphene platelets(GNPs)were prepared and modified via a scalable and eco-friendly mechanochemical approach.The produced GNPs is at 1.6-nm thickness with high electrical conductivity of~950 S/m.The structure-property relations of PUU/GNP nanocomposites were comprehensively investigated through morphology and mechanical properties measurements.The strong interface and high-density hydrogen bonds between modified GNPs(M-GNPs)and PUU significantly enhanced the mechanical properties of the PUU nanocomposite.The PUU composite showed 66.7%and 36.2%increments in tensile and impact strengths,respectively,at 0.2 wt% M-GNPs.The reversible hydrogen bond between M-GNPs and PUU endowed the nanocomposite with self-healing properties achieving 97.8% healing efficiency of the strength after 5 h at 120℃.This study demonstrates the importance of surface modification and provides a simple yet robust approach for preparing high-performance and functional PUU/graphene composites.展开更多
This study investigates the impacts of mixing time,execution procedure,cement dosage(α),and total water-to-cement ratio(W_(Total)/C)on the mixing energy(E)of deep soil mixing(DSM)columns and how E influences the stre...This study investigates the impacts of mixing time,execution procedure,cement dosage(α),and total water-to-cement ratio(W_(Total)/C)on the mixing energy(E)of deep soil mixing(DSM)columns and how E influences the strength of treated sand.Columns with a diameter of 7.5 cm were constructed using three mixing times(130,190,and 250 s),two execution procedures(normal and zigzag),threeαvalues(300,400,and 500 kg/m^(3)),and three W_(Total)/C ratios(2.5,3.0,and 3.5).For comparison,equivalent laboratory samples were also examined.Results revealed that increasing the mixing time andα,adopting the zigzag execution procedure,and reducing the W_(Total)/C ratio increase E.Outcomes indicated that an increase in E from 0.49-0.70 kJ to 0.70-0.90 kJ,0.90-1.10 kJ,and 1.10-1.40 kJ improves the unconfined compressive strength(UCS)of columns on average by 66%,124%,and 179%,respectively,and the secant modulus by 61%,110%,and 152%.Average strain at maximum stress also rises from 0.68%to 0.75%,0.81%,and 0.84%,respectively.The study identified a threshold in the direct relationship between E and the strength ratio(λ),beyond whichλdid not increase significantly with further increases in E.Additionally,at low and high E levels,DSM samples mainly failed by crushing and cracking modes,respectively.In DSM columns withα=500 kg/m^(3)and W_(Total)/C=2.5,increasing average E from 0.77 kJ to 0.95 kJ,1.08 kJ,and 1.28 kJ resulted in a reduction of coefficients of variation of UCS from 30.4%to 27.8%,24.5%,and 21.1%,respectively.展开更多
A novel method that combines reinforced enzyme-induced carbonate precipitation(REICP)was proposed to improve the mechanical properties of dispersive soil.Dispersive soils,which are highly susceptible to erosion caused...A novel method that combines reinforced enzyme-induced carbonate precipitation(REICP)was proposed to improve the mechanical properties of dispersive soil.Dispersive soils,which are highly susceptible to erosion caused by rainfall or seepage,pose significantenvironmental challenges.It is essential to focus on modifying dispersive soil using environmentally friendly methods.This study investigated the cohesion,internal friction angle,permeability,hydrostability test,and microstructure of dispersive soil treated with enzyme-induced carbonate precipitation(EICP)-MgCl2-xanthan gum(REICP),using statistical analysis.A series of laboratory experiments was conducted,including direct shear tests,permeability experiments,mud ball tests,simulated rainfall tests,Fourier transform infrared spectroscopy(FTIR),X-ray diffraction(XRD),and scanning electron microscopy(SEM).The results showed that the combined treatment significantly enhanced the mechanical properties of dispersive soil.At the optimal ratio,cohesion increased by a factor of 2,and the permeability coefficientdecreased by approximately 1.7×10^(7)times.Additionally,the strength parameters gradually increased with curing time.Microstructural analyses indicated that calcite precipitation,pore filling,and ionic redistribution significantlyimproved the mechanical properties and hydrostability of the soil.Statistical analyses showed that EICP materials and xanthan gum increased soil cohesion,while magnesium chloride enhanced the internal friction angle and reduced porosity.This study integrates mechanical testing,statistical analysis,and microstructural evaluation to propose a sustainable and environmentally friendly method for improving dispersive soils.This approach reduces the use of chemical modifiers,minimizes environmental impacts,and demonstrates application potential in the stabilization of dispersive soils.展开更多
This study aimed to produce and characterize mycelium leather(Mylea)derived from oil palm empty fruit bunch(OPEFB).Variations in OPEFB composition(10%,20%,30%,and 40%)were tested using a 10%w/w Ganoderma lucidum inocu...This study aimed to produce and characterize mycelium leather(Mylea)derived from oil palm empty fruit bunch(OPEFB).Variations in OPEFB composition(10%,20%,30%,and 40%)were tested using a 10%w/w Ganoderma lucidum inoculum.The mycelium underwent boiling,plasticization,drying,pressing,waxing,and Tencel fabric reinforcement to form Mylea.The physical,mechanical,and flammability properties of OPEFB-based Mylea were evaluated as a potential animal leather substitute.The highest tensile strength(8.47 MPa)was observed in the 0%OPEFB sample due to reinforcement with the Tencel fabric layer.Meanwhile,the 20%OPEFB sample after drying exhibited a tensile strength of 5.78 MPa and a lower elastic modulus(14.48 MPa),indicating increased flexibility but reduced stiffness.Among the tested compositions,20%OPEFB provided the best balance between growth time and material quality.Flammability tests showed that Mylea with 20%OPEFB had a longer burn time(43.5±7.78 s)compared to 0%OPEFB(21.0±1.41 s).However,the addition of OPEFB did not improve fire resistance,as none of the samples met UL 94 V-0,V-1,or V-2 standards.展开更多
Ceramic thin plates were prepared using kaolin,potassium sodium feldspar and quartz powder as the main raw materials and kaolin,α-Al_(2)O_(3),MoO_(3) and AlF_(3)·3H_(2)O as additives.The experiment examined the ...Ceramic thin plates were prepared using kaolin,potassium sodium feldspar and quartz powder as the main raw materials and kaolin,α-Al_(2)O_(3),MoO_(3) and AlF_(3)·3H_(2)O as additives.The experiment examined the effects of different additives on mullite formation,as well as the microstructure and properties of the ceramic thin plates.Additionally,the study explored the toughening and strengthening mechanisms induced by the additives,providing a theoretical foundation for further optimizing the toughness of ceramic thin plates.The results showed that the D4 sample fired at 1220℃(with an addition of 20 wt% α-Al_(2)O_(3))exhibited the best performance,with a water absorption rate of 0.07%,apparent porosity of 0.18%,bulk density of 2.75 g·cm^(-3),firing shrinkage of 12.76%,bending strength reaching 101.93 MPa,and fracture toughness of 2.51 MPa·m^(1/2).As the amount ofα-Al_(2)O_(3) additive increased,the ceramic thin plates exhibited a greater abundance of short rod-like mullite and corundum grains,which were tightly packed together,forming a framework for the ceramic thin plates.This microstructure enhanced pathways for crack propagation,dispersed internal stresses,and increased fracture surface energy,resulting in significant improvements in both strength and fracture toughness of the ceramic thin plates.展开更多
To exploit the combined strengthening effects of nanotwins and carbon nanotubes(CNTs)in Cu matrix composites,the nanotwins with a width ranging from 3 to 30 nm were incorporated into the CNTs-reinforced Cu matrix comp...To exploit the combined strengthening effects of nanotwins and carbon nanotubes(CNTs)in Cu matrix composites,the nanotwins with a width ranging from 3 to 30 nm were incorporated into the CNTs-reinforced Cu matrix composites using cryogenic rolling and optimizing the initial particle size of the raw Cu powders.The formation of nanotwins in the Cu matrix composite reinforced by only 0.2 wt.%CNTs is accompanied by the increased dislocation density and refined Cu grain size,resulting in much better strength−ductility synergy than the referenced composite without significant nanotwins formation.The analysis of strengthening and toughening mechanisms demonstrates that the strength increment mainly derives from grain refinement strengthening,dislocation strengthening,and nanotwin strengthening.The strength increment from the contribution of the nanotwins accounts for 19.9%of the overall strength increment for the composite.Meanwhile,the retention of good tensile ductility can be reasonably explained by the increased dislocation accommodation ability due to the formed nanotwins and the decreased induced dislocation proliferation.展开更多
This paper studies the structural response of high-speed train wipers under the combined action of complex flow fields and scraping actions.The stress concentration areas are determined through simulation analysis,and...This paper studies the structural response of high-speed train wipers under the combined action of complex flow fields and scraping actions.The stress concentration areas are determined through simulation analysis,and the stress and aerodynamic load measurement points are reasonably arranged accordingly.The actual measurement is carried out in combination with the operating conditions of the existing lines.The stress variations and spectral characteristics of the train under different speed levels(80,160,180,200 km/h),tunnel entry and exit,and scraper action conditions were compared and analyzed.The stress amplification factors under tunnel intersection and scraper action were obtained,providing boundary conditions for the design of wipers for highspeed s.The research results show that the maximum stress of the wiper structure obtained through simulation calculation is concentrated at the connection of the wiper arm.Structural stress increases with the rise of speed grade.The stress increases by 1.11 times when the tunnel meets.When the scraper operates,the stress on the scraper arm increases by 4.1–7.6 times.Due to the broadband excitation effect of the aerodynamic load,the spectral energy of the structure is relatively high at the natural frequency,which excites the natural mode of the wiper.展开更多
Investigations into the long-term creep behavior of Beishan granite in uniaxial compression were conducted.Four levels of axial stress(60,70,87,and 95 MPa)were applied to rock specimens.Contrasting with earlier resear...Investigations into the long-term creep behavior of Beishan granite in uniaxial compression were conducted.Four levels of axial stress(60,70,87,and 95 MPa)were applied to rock specimens.Contrasting with earlier research,the long-term creep data in this work present a substantial advancement in the time dimension.Except for the sample subjected to 60 MPa axial loading,which did not fail after a loading duration of 1650 d,the specimens under the other three stresses all failed after sustained constant loading durations of 1204,1023,and 839 d,respectively.A lower envelope of driving stress-ratio for crystalline rocks was obtained,tending towards approximately 0.45 over an infinite time scale.According to the experimental results,as axial stress increases,both the axial strain accumulated in the transient creep process and the strain rate associated with steady-state creep deformation increase exponentially;however,the share of steady-state creep strain remains nearly constant at about82.53%.A novel damage-based creep model was put forward.It provides an enhanced depiction of the comprehensive creep process in rocks,notably improving the accuracy in forecasting the accelerated creep phase,which significantly impacts the long-term stability of engineering structures.展开更多
To improve the applicability of red mud in subgrade construction,we studied the effects of four traditional retarders,including borax,sodium hexametaphosphate,sodium gluconate,and sucrose,on the setting time,mechanica...To improve the applicability of red mud in subgrade construction,we studied the effects of four traditional retarders,including borax,sodium hexametaphosphate,sodium gluconate,and sucrose,on the setting time,mechanical properties and soil solidification of red mud-based subgrade engineered cementitious material(RCM).The mechanisms of the retarders on the hydration process of RCM were analyzed by hydration microcalorimeter,XRD,TG,and SEM-EDS.The experimental results show that four retarders have retarding effect on RCM,among which sodium gluconate and sucrose have significant retarding effect and do not have adverse effect on 28 d strength.Borax can slightly delay the setting time,and sodium hexametaphosphate has a better retarding effect,but they both reduce the 28 d strength.Microcosmic analysis shows that the retarders do not change the type of RCM hydration products,but mainly slow down the rate of hydration reaction through the adsorption and complexation or reaction of Ca^(2+)in the slurry.All the results show that the retarder has no weakening effect on the unconfined compressive strength,water stability and CBR properties of the stabilized subgrade soil based on RCM.展开更多
Dynamic disturbances with various frequencies could trigger different failure modes of deep excavations.Superimposed on this static stress are dynamic disturbances due to various dynamic vibrations,e.g.excavation blas...Dynamic disturbances with various frequencies could trigger different failure modes of deep excavations.Superimposed on this static stress are dynamic disturbances due to various dynamic vibrations,e.g.excavation blasting,blasting,tunnel boring machine(TBM)vibration,rockburst wave,earthquakes.Specifically,these dynamic sources are characterized by a wide range of wave frequencies f,resulting in differences in failure modes.A series of true-triaxial compression tests were conducted on granite to simulate the excavation-induced stress path in three-dimensional(3D)stresses.Subsequently,a dynamic disturbance with various frequencies was applied to a cuboid specimen,to reveal the behavior associated with brittle failure.The dynamic disturbance with frequencies f of 5 Hz,10 Hz,and 40 Hz generates less disturbed energy components in the granite together with higher peak strength.However,dynamic disturbances with f of 20 Hz and 30 Hz resulted in a lower peak strength;the peak strength of the rock increases sp albeit it decreases at first,then increases.This U-shaped phenomenon relates to the natural frequency of the granite under such stress conditions.Different rock lithologies consisting of diverse mineral composition,respond differently to each sensitive resonance frequency.Interestingly,the weak disturbance stress with a high frequency f and low amplitude A increases the ratio of crack damage to peak strength(scd/sp)in the granite.This leads to the inhibition of the expansion of the granite during the dynamic disturbance process.Multiple penetrating tensileeshear cracks appear in the s3-direction as the disturbance frequency f increases.展开更多
The insufficient absolute strength of Mg-Li alloys severely restricts their aerospace applications.To address this limitation,a dual-phase Mg-Li alloy with enhanced strength was fabricated through rapid solidification...The insufficient absolute strength of Mg-Li alloys severely restricts their aerospace applications.To address this limitation,a dual-phase Mg-Li alloy with enhanced strength was fabricated through rapid solidification combined with hot-press sintering and extrusion.The optimized alloy exhibited yield and ultimate tensile strengths of 283 MPa and 306 MPa under quasi-static loading,respectively,while retaining a uniform elongation of 6%.Multiscale microstructural characterization via XRD,SEM-EBSD,and TEM revealed that rapid solidification induced remarkable grain refinement and precipitate redistribution.Subsequent thermomechanical processing achieved full dynamic recrystallization with refined grains.Crucially,the rapid solidification kinetics notably altered Al partitioning,favoring solid solution in magnesium phase over precipitation in lithium phase.These microstructural modifications activate synergistic strengthening mechanisms:1)Hall-Petch hardening from grain refinement,2)dispersion strengthening via nano-precipitates,3)dislocation strengthening from substructures,and 4)solid solution effects from Al supersaturation.This work establishes a microstructure design paradigm for high-performance Mg-Li alloys through coupled rapid solidification and thermomechanical processing.展开更多
The development of epoxy(EP)nanocomposites has emerged as a prominent research area across diverse sectors,including automotive,construction,and aerospace industries.Recently,adopting biomimetic strategies for the pre...The development of epoxy(EP)nanocomposites has emerged as a prominent research area across diverse sectors,including automotive,construction,and aerospace industries.Recently,adopting biomimetic strategies for the preparation of nanomaterials to design multifunctional epoxy resins has emerged as a prominent research hotspot.Inspired by the growth pattern of coral reefs,this study successfully engineered a novel hierarchical nanostructured material(Fe-NiPS-PBA)with the aim of creating EP nanocomposites that exhibit highly flame-retardant efficiency,exceptional mechanical strength,and distinguished wear-resisting property even at low additive concentrations.With a 3 wt%addition of Fe-NiPS-PBA,the limiting oxygen index of the EP/3Fe-NiPS-PBA nanocomposite increased from 23.5 to 25.9,achieving a UL-94 V-0 rating.Compared to pure EP,EP/3Fe-NiPSPBA nanocomposite reduced the peak heat release rate(PHRR),total heat release(THR),peak smoke production rate(PSPR),total smoke production(TSP),and maximum CO emission(MCO)by 44.1%,66.7%,47.0%,67.8%,and 51.7%,respectively.Moreover,the incorporation of a 1 wt%additive resulted in significant enhancements of tensile strength from 76.7 MPa to 96.9 MPa,while the wear rate demonstrated a remarkable reduction of 77.8%.The Fe-NiPS-PBA significantly enhanced the fire performance and mechanical strength of EP nanocomposites,demonstrating exceptional overall performance in various applications.展开更多
Community detection is a fundamental problem in network analysis for identifying densely connected node clusters,with successful applications in diverse fields like social networks,recommendation systems,biology,and c...Community detection is a fundamental problem in network analysis for identifying densely connected node clusters,with successful applications in diverse fields like social networks,recommendation systems,biology,and cyberattack detection.Overlapping community detection refers to the case of a node belonging to multiple communities simultaneously,which is a much more meaningful and challenging task.Graph representation learning with Evolutionary Computation has been studied well in overlapping community detection to deal with complex network structures and characteristics.However,most of them focus on searching the entire solution space,which can be inefficient and lead to inadequate results.To overcome the problem,a structural feature node extraction method is first proposed that can effectively map a network into a structural embedding space.Thus,nodes within the network are classified into hierarchical levels based on their structural feature strength,and only nodes with relatively high strength are considered in subsequent search steps to reduce the search space.Then,a maximal-clique representation method is employed on the given vertex set to identify overlapping nodes.A hybrid clique-based multi-objective evolutionary algorithmwith decomposition method is designed to address cliques and the remaining unexplored nodes separately.The number of communities generated with this allocation method is closer to the actual partition count with high division quality.Experimental results on nine usually used real-world networks,five synthetic networks,and two large-scale networks demonstrate the effectiveness of the proposed methodology in terms of community quality and algorithmic efficiency,compared to traditional,MOEA-based,and graph embedding-based community detection algorithms.展开更多
This study investigates the performance enhancement of super-sulfated cement(SSC)derived from arsenic-containing bio-oxidation waste(BW)through the incorporation of carbonated recycled concrete fines(CRCF).The finding...This study investigates the performance enhancement of super-sulfated cement(SSC)derived from arsenic-containing bio-oxidation waste(BW)through the incorporation of carbonated recycled concrete fines(CRCF).The findings revealed that the addition of 5wt%CRCF yields optimal performance,with compressive strengths reaching approximately 1.83,12.59,and 42.81 MPa at 1,3,and 28 d,respectively.These values represented significant increases of 408.3%,10.0%,and 14.3%compared to the reference sample.The improvement was attributed to the synergistic effects of ultrafine CRCF particles acting as fillers and nucleation sites,as well as the high reactivity of silica gels,which promoted the formation of additional hydration gels.Microstructural analysis confirmed that CRCF addition refined pore structure,and enhanced the stiffness of C-S-H gels.Furthermore,CRCF served as a net CO_(2) sink,sequestering 0.268 kg CO_(2) per kilogram of CRCF and thereby reducing the carbon footprint of SSC.In addition,the feasibility of applying CRCF-modified SSC in cemented paste backfill(CPB)is highlighted,given the high cement-related carbon footprint of conventional CPB.When 5wt%CRCFmodified SSC was employed in CPB,its 3-d compressive strength attained over 70%of that of ordinary Portland cement(OPC),while the 28-d strength was comparable to that of OPC.The proposed binder thus provides a sustainable pathway for BW valorization,combining waste utilization,carbon sequestration,and improved engineering performance.展开更多
Stability of base-exposed backfill roof in underhand drift-and-fill mining is crucial for the safety of those working beneath.Given the commonly used primary-and-secondary mining sequence,interfaces are formed between...Stability of base-exposed backfill roof in underhand drift-and-fill mining is crucial for the safety of those working beneath.Given the commonly used primary-and-secondary mining sequence,interfaces are formed between adjacent filled drifts,which can weaken the integrity of the backfill roof.These interfaces also lead to two common drift layouts:aligned drifts and staggered drifts.However,less attention has been paid to the interfaces and the two drift layouts were not adequately distinguished in previous studies.In this paper,the interfaces between filled drifts were firstly considered to investigate the stability of backfill roof.Failure modes and strength requirements of backfill roof in aligned and staggered drifts are comprehensively investigated by FLAC3D,with a focus on considerations of varied shear parameters of the interfaces.Results show that failure modes in aligned drifts transition from block sliding to top caving,bottom caving or sloughing as the interface cohesion increases from zero to at least half of the backfill cohesion.Further increases in interface cohesion allow aligned drifts to behave as if there are no interfaces between them.The critical stability conditions of backfill roof in aligned drifts were mostly determined by the interface strength instead of the backfill strength.However,the stability of backfill roof in staggered drifts is barely affected by the interface strength.The outcomes are expected to provide references for mining engineers to optimize drift layouts and perform cost-effective backfill roof strength design at mines using underhand drift-and-fill mining method.展开更多
基金National Key Research and Development Program of China(2021YFB3700801)。
文摘Low-density short-duration pulsed current-assisted aging treatment was applied to the Ti-6Al-4V-0.5Mo-0.5Zr alloy subjected to different solution treatments.The results show that numerous α_(p) phases redissolve into the new β phase during the pulsed current-assisted aging process,and then the newly formed β phase is mainly transformed into the β_(t) phase,with occasional transition to new α_(p) phase,leading to a remarkable grain refinement,especially for the lamellarαs phases.In comparison to conventional aging treatment,the pulsed current-assisted aging approach achieves a significant enhancement in strength without degrading ductility,yielding an excellent mechanical property combination:a yield strength of 932 MPa,a tensile strength of 1042 MPa,and an elongation of 12.2%.It is primarily ascribed to the increased fraction of β_(t) phases,the obvious grain refinement effect,and the slip block effect induced by the multiple-variantαs colonies distributed within β_(t) phases.
文摘In view of the phenomenon that the adhesion strength between the surface of polyacrylonitrile-butadiene-styrene-polycarbonate(ABS-PC)copolymer and the electroless copper plating layer is relatively low.To solve the problems of poor surface wettability and low surface roughness of the ABS-PC substrate,the N,N-dimethylformamide(DMF)-ethanol(C_(2)H_(5)OH)-water(H_(2)O)system was employed as the swelling system for the ABS-PC substrate.The effects of the DMF volume fraction in the swelling system and the swelling time on the swelling effect of ABS-PC at 35℃ were investigated.KMnO_(4)-H_(2)SO_(4)-H_(2)O system was used as the etching system for ABS-PC substrate under the conditions of the volume ratio of water to sulfuric acid of 1﹕2,with KMnO_(4) content of 30 g/L,etching temperature of 60℃,and etching time of 25 min.The results indicate that dense pores with uniform sized are formed on the surface of the ABS-PC substrate surface after swelling and etching treatments,accompanied by an increase in surface roughness when the swelling temperature is 35℃,the DMF volume fraction in the swelling system is 80%,and the swelling time is 5 min.Furthermore,the content of C element on the surface of the ABS-PC substrate decreased,while that of O element increased,and the surface hydrophilicity is enhanced,which is attributed to two hydrophilic groups,-C=O and-COOH,being generated on the ABS-PC substrate surface,significantly improving the wettability of the ABS-PC substrate surface.Under the combination effects of high surface roughness and strong surface hydrophilicity,the adhesion strength between the ABS-PC substrate surface and the electroless copper plating layer reached to 0.81 kN/m,meeting the adhesion strength requirement of 0.70 kN/m in the industrial production.
文摘We report a method for increasing the mechanical strength of carbon nanotube(CNT)fibers while enabling the uniform adhesion of cerium oxide(CeO_(2))abrasive particles to them using polyethyleneimine(PEI).Results show that 5%of PEI increases the tensile strength of CNT fibers by approximately 175%.CeO_(2) particles were uniformly deposited on the reinforced CNT fibers by electrophoretic deposition.A flexible polishing tool was fabricated by weaving the CeO_(2)-CNT fibers into a non-woven fabric substrate.When used to polish potassium dihydrogen phosphate crystals,the tool reduced the surface roughness from 200 to 7.6 nm within 10 min.This approach has potential use for the development of new precision processing tools.
文摘Chinese President Xi Jinping’s New Year message summarized an important year of steady progress as the country prepares to launch its 15th Five-Year Plan.“Our economic strength,scientific and technological abilities,defense capabilities,and composite national strength all reached new heights.”declared President Xi Jinping in his 2026 New Year message on De-By CHINA TODAY cember 31,2025,offering a succinct summary of China’s development over the past year,marked by resilience,progress,and renewed confidence as the country stands at the threshold of a new development phase.
基金supported by the Natural Science Foundation of China(Grant Nos.T2325013,52288102,52090024,12034009,12474004,and 12304036)the National Key R&D Program of China Grant No.2023YFA1610000+1 种基金the Fundamental Research Funds for the Central Universitiesthe Program for Jilin University and Sun Yat-sen University.
文摘We report first-principles predictions of a cage-like polymeric nitrogen phase(cage-N)composed of interlocked N10 clusters stabilized by mixed sp^(2)/sp^(3) hybridization.Under high pressure,cage-N exhibits exceptional mechanical performance,including an ideal compressive strength of 343 GPa at a pressure of 300 GPa,~33% higher than that of diamond.This ultrahigh strength arises from the synergistic interplay between its three-dimensional covalent framework and hybridized bonding topology,which enables isotropic stress accommodation and dynamic electronic rearrangement.These results establish cage-N as a promising non-carbon ultrahard material and provide a bonding-driven route toward designing superhard frameworks under extreme conditions.
基金The National Natural Science Foundation of China(No.52173077)the Liaoning Provincial Department of Education Series Project(No.LJKZ0187)+1 种基金Natural Science Foundation of Liaoning Province(No.2023-MS-239)Liaoning BaiQianWan Talents Program(No.2021921081)。
文摘In this study,a facile method was employed to synthesize strong,yet highly elastic polyurethane-urea(PUU)with typical characteristics and 94% optical transmittance.Graphene platelets(GNPs)were prepared and modified via a scalable and eco-friendly mechanochemical approach.The produced GNPs is at 1.6-nm thickness with high electrical conductivity of~950 S/m.The structure-property relations of PUU/GNP nanocomposites were comprehensively investigated through morphology and mechanical properties measurements.The strong interface and high-density hydrogen bonds between modified GNPs(M-GNPs)and PUU significantly enhanced the mechanical properties of the PUU nanocomposite.The PUU composite showed 66.7%and 36.2%increments in tensile and impact strengths,respectively,at 0.2 wt% M-GNPs.The reversible hydrogen bond between M-GNPs and PUU endowed the nanocomposite with self-healing properties achieving 97.8% healing efficiency of the strength after 5 h at 120℃.This study demonstrates the importance of surface modification and provides a simple yet robust approach for preparing high-performance and functional PUU/graphene composites.
文摘This study investigates the impacts of mixing time,execution procedure,cement dosage(α),and total water-to-cement ratio(W_(Total)/C)on the mixing energy(E)of deep soil mixing(DSM)columns and how E influences the strength of treated sand.Columns with a diameter of 7.5 cm were constructed using three mixing times(130,190,and 250 s),two execution procedures(normal and zigzag),threeαvalues(300,400,and 500 kg/m^(3)),and three W_(Total)/C ratios(2.5,3.0,and 3.5).For comparison,equivalent laboratory samples were also examined.Results revealed that increasing the mixing time andα,adopting the zigzag execution procedure,and reducing the W_(Total)/C ratio increase E.Outcomes indicated that an increase in E from 0.49-0.70 kJ to 0.70-0.90 kJ,0.90-1.10 kJ,and 1.10-1.40 kJ improves the unconfined compressive strength(UCS)of columns on average by 66%,124%,and 179%,respectively,and the secant modulus by 61%,110%,and 152%.Average strain at maximum stress also rises from 0.68%to 0.75%,0.81%,and 0.84%,respectively.The study identified a threshold in the direct relationship between E and the strength ratio(λ),beyond whichλdid not increase significantly with further increases in E.Additionally,at low and high E levels,DSM samples mainly failed by crushing and cracking modes,respectively.In DSM columns withα=500 kg/m^(3)and W_(Total)/C=2.5,increasing average E from 0.77 kJ to 0.95 kJ,1.08 kJ,and 1.28 kJ resulted in a reduction of coefficients of variation of UCS from 30.4%to 27.8%,24.5%,and 21.1%,respectively.
基金supported by the National Natural Science Foundation of China(Grant No.42407199)Heilongjiang Provincial Natural Science Foundation of China(Grant No.PL2024D003)the Fundamental Research Funds for the Central Universities(Grant No.2572023CT17).
文摘A novel method that combines reinforced enzyme-induced carbonate precipitation(REICP)was proposed to improve the mechanical properties of dispersive soil.Dispersive soils,which are highly susceptible to erosion caused by rainfall or seepage,pose significantenvironmental challenges.It is essential to focus on modifying dispersive soil using environmentally friendly methods.This study investigated the cohesion,internal friction angle,permeability,hydrostability test,and microstructure of dispersive soil treated with enzyme-induced carbonate precipitation(EICP)-MgCl2-xanthan gum(REICP),using statistical analysis.A series of laboratory experiments was conducted,including direct shear tests,permeability experiments,mud ball tests,simulated rainfall tests,Fourier transform infrared spectroscopy(FTIR),X-ray diffraction(XRD),and scanning electron microscopy(SEM).The results showed that the combined treatment significantly enhanced the mechanical properties of dispersive soil.At the optimal ratio,cohesion increased by a factor of 2,and the permeability coefficientdecreased by approximately 1.7×10^(7)times.Additionally,the strength parameters gradually increased with curing time.Microstructural analyses indicated that calcite precipitation,pore filling,and ionic redistribution significantlyimproved the mechanical properties and hydrostability of the soil.Statistical analyses showed that EICP materials and xanthan gum increased soil cohesion,while magnesium chloride enhanced the internal friction angle and reduced porosity.This study integrates mechanical testing,statistical analysis,and microstructural evaluation to propose a sustainable and environmentally friendly method for improving dispersive soils.This approach reduces the use of chemical modifiers,minimizes environmental impacts,and demonstrates application potential in the stabilization of dispersive soils.
基金supported by the Palm Oil Plantation Fund Management Agency(BPDPKS),Indonesia 2024.
文摘This study aimed to produce and characterize mycelium leather(Mylea)derived from oil palm empty fruit bunch(OPEFB).Variations in OPEFB composition(10%,20%,30%,and 40%)were tested using a 10%w/w Ganoderma lucidum inoculum.The mycelium underwent boiling,plasticization,drying,pressing,waxing,and Tencel fabric reinforcement to form Mylea.The physical,mechanical,and flammability properties of OPEFB-based Mylea were evaluated as a potential animal leather substitute.The highest tensile strength(8.47 MPa)was observed in the 0%OPEFB sample due to reinforcement with the Tencel fabric layer.Meanwhile,the 20%OPEFB sample after drying exhibited a tensile strength of 5.78 MPa and a lower elastic modulus(14.48 MPa),indicating increased flexibility but reduced stiffness.Among the tested compositions,20%OPEFB provided the best balance between growth time and material quality.Flammability tests showed that Mylea with 20%OPEFB had a longer burn time(43.5±7.78 s)compared to 0%OPEFB(21.0±1.41 s).However,the addition of OPEFB did not improve fire resistance,as none of the samples met UL 94 V-0,V-1,or V-2 standards.
基金Funded by the National Key Technology Research and Development Program of the Ministry of Science and Technology of China(No.2023YFB4204302)。
文摘Ceramic thin plates were prepared using kaolin,potassium sodium feldspar and quartz powder as the main raw materials and kaolin,α-Al_(2)O_(3),MoO_(3) and AlF_(3)·3H_(2)O as additives.The experiment examined the effects of different additives on mullite formation,as well as the microstructure and properties of the ceramic thin plates.Additionally,the study explored the toughening and strengthening mechanisms induced by the additives,providing a theoretical foundation for further optimizing the toughness of ceramic thin plates.The results showed that the D4 sample fired at 1220℃(with an addition of 20 wt% α-Al_(2)O_(3))exhibited the best performance,with a water absorption rate of 0.07%,apparent porosity of 0.18%,bulk density of 2.75 g·cm^(-3),firing shrinkage of 12.76%,bending strength reaching 101.93 MPa,and fracture toughness of 2.51 MPa·m^(1/2).As the amount ofα-Al_(2)O_(3) additive increased,the ceramic thin plates exhibited a greater abundance of short rod-like mullite and corundum grains,which were tightly packed together,forming a framework for the ceramic thin plates.This microstructure enhanced pathways for crack propagation,dispersed internal stresses,and increased fracture surface energy,resulting in significant improvements in both strength and fracture toughness of the ceramic thin plates.
基金financially supported by the Fundamental Research Funds for the Central Universities,China(No.21624408)the Guangdong Basic and Applied Basic Research Foundation,China(Nos.2023A1515012850,2024A1515010416)+2 种基金Guangzhou Science and Technology Planning Project,China(No.2024A04J9966)the National Natural Science Foundation of China(Nos.52271132,52004101)the Key Laboratory of Advanced Materials of Yunnan Province,China(No.2024KF02)。
文摘To exploit the combined strengthening effects of nanotwins and carbon nanotubes(CNTs)in Cu matrix composites,the nanotwins with a width ranging from 3 to 30 nm were incorporated into the CNTs-reinforced Cu matrix composites using cryogenic rolling and optimizing the initial particle size of the raw Cu powders.The formation of nanotwins in the Cu matrix composite reinforced by only 0.2 wt.%CNTs is accompanied by the increased dislocation density and refined Cu grain size,resulting in much better strength−ductility synergy than the referenced composite without significant nanotwins formation.The analysis of strengthening and toughening mechanisms demonstrates that the strength increment mainly derives from grain refinement strengthening,dislocation strengthening,and nanotwin strengthening.The strength increment from the contribution of the nanotwins accounts for 19.9%of the overall strength increment for the composite.Meanwhile,the retention of good tensile ductility can be reasonably explained by the increased dislocation accommodation ability due to the formed nanotwins and the decreased induced dislocation proliferation.
文摘This paper studies the structural response of high-speed train wipers under the combined action of complex flow fields and scraping actions.The stress concentration areas are determined through simulation analysis,and the stress and aerodynamic load measurement points are reasonably arranged accordingly.The actual measurement is carried out in combination with the operating conditions of the existing lines.The stress variations and spectral characteristics of the train under different speed levels(80,160,180,200 km/h),tunnel entry and exit,and scraper action conditions were compared and analyzed.The stress amplification factors under tunnel intersection and scraper action were obtained,providing boundary conditions for the design of wipers for highspeed s.The research results show that the maximum stress of the wiper structure obtained through simulation calculation is concentrated at the connection of the wiper arm.Structural stress increases with the rise of speed grade.The stress increases by 1.11 times when the tunnel meets.When the scraper operates,the stress on the scraper arm increases by 4.1–7.6 times.Due to the broadband excitation effect of the aerodynamic load,the spectral energy of the structure is relatively high at the natural frequency,which excites the natural mode of the wiper.
基金financially supported by the China Atomic Energy Authority(CAEA)through the Geological Disposal Programthe National Natural Science Foundation of China(No.42307258)the China National Nuclear Corporation Fundamental Research Project(No.CNNC-JCYJ-202307)。
文摘Investigations into the long-term creep behavior of Beishan granite in uniaxial compression were conducted.Four levels of axial stress(60,70,87,and 95 MPa)were applied to rock specimens.Contrasting with earlier research,the long-term creep data in this work present a substantial advancement in the time dimension.Except for the sample subjected to 60 MPa axial loading,which did not fail after a loading duration of 1650 d,the specimens under the other three stresses all failed after sustained constant loading durations of 1204,1023,and 839 d,respectively.A lower envelope of driving stress-ratio for crystalline rocks was obtained,tending towards approximately 0.45 over an infinite time scale.According to the experimental results,as axial stress increases,both the axial strain accumulated in the transient creep process and the strain rate associated with steady-state creep deformation increase exponentially;however,the share of steady-state creep strain remains nearly constant at about82.53%.A novel damage-based creep model was put forward.It provides an enhanced depiction of the comprehensive creep process in rocks,notably improving the accuracy in forecasting the accelerated creep phase,which significantly impacts the long-term stability of engineering structures.
基金Funded by the Shandong Province Key R&D Program(Major Technological Innovation Project(Nos.2023ZLGX01 and 2021CXGC010301)the Youth Project of National Natural Science Foundation(No.52309136)+1 种基金the Competitive Innovation Platform Project of Shandong Province(No.2023CXPT-080)the Postdoctoral Innovation Project(No.SDCX-ZG-202203037)。
文摘To improve the applicability of red mud in subgrade construction,we studied the effects of four traditional retarders,including borax,sodium hexametaphosphate,sodium gluconate,and sucrose,on the setting time,mechanical properties and soil solidification of red mud-based subgrade engineered cementitious material(RCM).The mechanisms of the retarders on the hydration process of RCM were analyzed by hydration microcalorimeter,XRD,TG,and SEM-EDS.The experimental results show that four retarders have retarding effect on RCM,among which sodium gluconate and sucrose have significant retarding effect and do not have adverse effect on 28 d strength.Borax can slightly delay the setting time,and sodium hexametaphosphate has a better retarding effect,but they both reduce the 28 d strength.Microcosmic analysis shows that the retarders do not change the type of RCM hydration products,but mainly slow down the rate of hydration reaction through the adsorption and complexation or reaction of Ca^(2+)in the slurry.All the results show that the retarder has no weakening effect on the unconfined compressive strength,water stability and CBR properties of the stabilized subgrade soil based on RCM.
基金supported by the National Natural Science Foundation of China(Grant Nos.52222810 and 52178383).
文摘Dynamic disturbances with various frequencies could trigger different failure modes of deep excavations.Superimposed on this static stress are dynamic disturbances due to various dynamic vibrations,e.g.excavation blasting,blasting,tunnel boring machine(TBM)vibration,rockburst wave,earthquakes.Specifically,these dynamic sources are characterized by a wide range of wave frequencies f,resulting in differences in failure modes.A series of true-triaxial compression tests were conducted on granite to simulate the excavation-induced stress path in three-dimensional(3D)stresses.Subsequently,a dynamic disturbance with various frequencies was applied to a cuboid specimen,to reveal the behavior associated with brittle failure.The dynamic disturbance with frequencies f of 5 Hz,10 Hz,and 40 Hz generates less disturbed energy components in the granite together with higher peak strength.However,dynamic disturbances with f of 20 Hz and 30 Hz resulted in a lower peak strength;the peak strength of the rock increases sp albeit it decreases at first,then increases.This U-shaped phenomenon relates to the natural frequency of the granite under such stress conditions.Different rock lithologies consisting of diverse mineral composition,respond differently to each sensitive resonance frequency.Interestingly,the weak disturbance stress with a high frequency f and low amplitude A increases the ratio of crack damage to peak strength(scd/sp)in the granite.This leads to the inhibition of the expansion of the granite during the dynamic disturbance process.Multiple penetrating tensileeshear cracks appear in the s3-direction as the disturbance frequency f increases.
基金supported by The National Natural Science Foundation of China(Grant No.62204197)the Key R&D and Transformation Plan of Science and Technology Department of Qinghai Province(Grant No.2022-GX-156)Xi'an Association for Science and Technology(Grant No.959202313058).
文摘The insufficient absolute strength of Mg-Li alloys severely restricts their aerospace applications.To address this limitation,a dual-phase Mg-Li alloy with enhanced strength was fabricated through rapid solidification combined with hot-press sintering and extrusion.The optimized alloy exhibited yield and ultimate tensile strengths of 283 MPa and 306 MPa under quasi-static loading,respectively,while retaining a uniform elongation of 6%.Multiscale microstructural characterization via XRD,SEM-EBSD,and TEM revealed that rapid solidification induced remarkable grain refinement and precipitate redistribution.Subsequent thermomechanical processing achieved full dynamic recrystallization with refined grains.Crucially,the rapid solidification kinetics notably altered Al partitioning,favoring solid solution in magnesium phase over precipitation in lithium phase.These microstructural modifications activate synergistic strengthening mechanisms:1)Hall-Petch hardening from grain refinement,2)dispersion strengthening via nano-precipitates,3)dislocation strengthening from substructures,and 4)solid solution effects from Al supersaturation.This work establishes a microstructure design paradigm for high-performance Mg-Li alloys through coupled rapid solidification and thermomechanical processing.
基金Outstanding Youth Scientific Research Project in Anhui Province(2022AH020055)Key Research and Development Projects in Anhui Province(2022i01020016)。
文摘The development of epoxy(EP)nanocomposites has emerged as a prominent research area across diverse sectors,including automotive,construction,and aerospace industries.Recently,adopting biomimetic strategies for the preparation of nanomaterials to design multifunctional epoxy resins has emerged as a prominent research hotspot.Inspired by the growth pattern of coral reefs,this study successfully engineered a novel hierarchical nanostructured material(Fe-NiPS-PBA)with the aim of creating EP nanocomposites that exhibit highly flame-retardant efficiency,exceptional mechanical strength,and distinguished wear-resisting property even at low additive concentrations.With a 3 wt%addition of Fe-NiPS-PBA,the limiting oxygen index of the EP/3Fe-NiPS-PBA nanocomposite increased from 23.5 to 25.9,achieving a UL-94 V-0 rating.Compared to pure EP,EP/3Fe-NiPSPBA nanocomposite reduced the peak heat release rate(PHRR),total heat release(THR),peak smoke production rate(PSPR),total smoke production(TSP),and maximum CO emission(MCO)by 44.1%,66.7%,47.0%,67.8%,and 51.7%,respectively.Moreover,the incorporation of a 1 wt%additive resulted in significant enhancements of tensile strength from 76.7 MPa to 96.9 MPa,while the wear rate demonstrated a remarkable reduction of 77.8%.The Fe-NiPS-PBA significantly enhanced the fire performance and mechanical strength of EP nanocomposites,demonstrating exceptional overall performance in various applications.
基金supported in part by the National Natural Science Foundation of China under Grants 62473176,62073155,62002137,62106088,and 62206113National Key Laboratory of Ship Structural Safety underGrant 450324300the Postgraduate Research&Practice Innovation Programof Jiangsu Province under Grant KYCX24_2642.
文摘Community detection is a fundamental problem in network analysis for identifying densely connected node clusters,with successful applications in diverse fields like social networks,recommendation systems,biology,and cyberattack detection.Overlapping community detection refers to the case of a node belonging to multiple communities simultaneously,which is a much more meaningful and challenging task.Graph representation learning with Evolutionary Computation has been studied well in overlapping community detection to deal with complex network structures and characteristics.However,most of them focus on searching the entire solution space,which can be inefficient and lead to inadequate results.To overcome the problem,a structural feature node extraction method is first proposed that can effectively map a network into a structural embedding space.Thus,nodes within the network are classified into hierarchical levels based on their structural feature strength,and only nodes with relatively high strength are considered in subsequent search steps to reduce the search space.Then,a maximal-clique representation method is employed on the given vertex set to identify overlapping nodes.A hybrid clique-based multi-objective evolutionary algorithmwith decomposition method is designed to address cliques and the remaining unexplored nodes separately.The number of communities generated with this allocation method is closer to the actual partition count with high division quality.Experimental results on nine usually used real-world networks,five synthetic networks,and two large-scale networks demonstrate the effectiveness of the proposed methodology in terms of community quality and algorithmic efficiency,compared to traditional,MOEA-based,and graph embedding-based community detection algorithms.
基金supports from the National Natural Science Foundation of China(No.52304148)the Youth Project of Shanxi Basic Research Program(No.202203021212262).
文摘This study investigates the performance enhancement of super-sulfated cement(SSC)derived from arsenic-containing bio-oxidation waste(BW)through the incorporation of carbonated recycled concrete fines(CRCF).The findings revealed that the addition of 5wt%CRCF yields optimal performance,with compressive strengths reaching approximately 1.83,12.59,and 42.81 MPa at 1,3,and 28 d,respectively.These values represented significant increases of 408.3%,10.0%,and 14.3%compared to the reference sample.The improvement was attributed to the synergistic effects of ultrafine CRCF particles acting as fillers and nucleation sites,as well as the high reactivity of silica gels,which promoted the formation of additional hydration gels.Microstructural analysis confirmed that CRCF addition refined pore structure,and enhanced the stiffness of C-S-H gels.Furthermore,CRCF served as a net CO_(2) sink,sequestering 0.268 kg CO_(2) per kilogram of CRCF and thereby reducing the carbon footprint of SSC.In addition,the feasibility of applying CRCF-modified SSC in cemented paste backfill(CPB)is highlighted,given the high cement-related carbon footprint of conventional CPB.When 5wt%CRCFmodified SSC was employed in CPB,its 3-d compressive strength attained over 70%of that of ordinary Portland cement(OPC),while the 28-d strength was comparable to that of OPC.The proposed binder thus provides a sustainable pathway for BW valorization,combining waste utilization,carbon sequestration,and improved engineering performance.
基金supported by Deep Earth Probe and Mineral Resources Exploration-National Science and Technology Major Project(Grant No.2024ZD1003705)the Beijing Nova Program(Grant No.20220484057)support from China Scholarship Council under Grant CSC No.202110300001.
文摘Stability of base-exposed backfill roof in underhand drift-and-fill mining is crucial for the safety of those working beneath.Given the commonly used primary-and-secondary mining sequence,interfaces are formed between adjacent filled drifts,which can weaken the integrity of the backfill roof.These interfaces also lead to two common drift layouts:aligned drifts and staggered drifts.However,less attention has been paid to the interfaces and the two drift layouts were not adequately distinguished in previous studies.In this paper,the interfaces between filled drifts were firstly considered to investigate the stability of backfill roof.Failure modes and strength requirements of backfill roof in aligned and staggered drifts are comprehensively investigated by FLAC3D,with a focus on considerations of varied shear parameters of the interfaces.Results show that failure modes in aligned drifts transition from block sliding to top caving,bottom caving or sloughing as the interface cohesion increases from zero to at least half of the backfill cohesion.Further increases in interface cohesion allow aligned drifts to behave as if there are no interfaces between them.The critical stability conditions of backfill roof in aligned drifts were mostly determined by the interface strength instead of the backfill strength.However,the stability of backfill roof in staggered drifts is barely affected by the interface strength.The outcomes are expected to provide references for mining engineers to optimize drift layouts and perform cost-effective backfill roof strength design at mines using underhand drift-and-fill mining method.
