The hot deformation behavior of GH3230 superalloy under selected deformation conditions ranging from 950 to 1150℃with strain rates ranging from 0.01 to 10 s^(–1)was studied through isothermal hot compression experim...The hot deformation behavior of GH3230 superalloy under selected deformation conditions ranging from 950 to 1150℃with strain rates ranging from 0.01 to 10 s^(–1)was studied through isothermal hot compression experiments.Based on the obtained flow stresses,a strain-compensated Arrhenius-type model was developed for the description of hot deformation behavior,and the consistency of the predicted flow stresses with the experimental values confirms the accuracy of the developed model.Furthermore,the processing maps were constructed and classified into the instability domain,low-dissipation stability domain and high-dissipation stability domain in accordance with the dynamic material model and the instability criterion.Microstructure observations indicated that the instability domain exhibits the adiabatic shear bands formation,and the low-power dissipation domain exhibits partial dynamic recrystallization(DRX),with the temperature increase/strain rate decrease being favorable for the DRX.The high-dissipation stability domain was occupied by uniformly fine equiaxed grains,and was identified as the optimal processing window,which corresponds to the deformation conditions at 1070–1150℃ with strain rates ranging from 0.01 to 0.15 s^(–1).Moreover,various DRX mechanisms are observed to occur during the hot deformation,which include the discontinuous dynamic recrystallization,characterized by nucleation at bulged boundaries,the continuous dynamic recrystallization with subgrain progressive rotation and the particle stimulated nucleation mechanism with stimulated nucleation of carbide particles.展开更多
The microstructure and texture evolutions during extrusion and rolling processes of the 2195 Al−Li alloy were investigated.The EBSD technique was employed to reveal the microscopic evolution mechanisms of different te...The microstructure and texture evolutions during extrusion and rolling processes of the 2195 Al−Li alloy were investigated.The EBSD technique was employed to reveal the microscopic evolution mechanisms of different texture components.The findings reveal that the texture evolution is governed by two mechanisms:an overall orientation transformation induced by plastic strain and a localized transformation occurring at the shearing bands within grains.During the rolling process,the extrusion texture components of Ex{123}<111>and Cu{112}<111>evolve into S{123}<634>,and the Bs{011}<211>rotates into the orientations near R-Bs and S.With increasing deformation,the S,Bs,and R-Bs orientations further rotate around the TD axis and disperse into new orientations,forming recrystallized grains.The shearing bands with different initial orientations exhibit similar orientation evolution patterns,all of which evolve from the initial orientation to a series of recrystallization orientations.展开更多
The initial microstructure of titanium alloy in theα+βphase region is pivotal in dictating the performance of the final products after thermomechanical processing.Microstructures and textures of three rods,each prep...The initial microstructure of titanium alloy in theα+βphase region is pivotal in dictating the performance of the final products after thermomechanical processing.Microstructures and textures of three rods,each prepared through distinct pretreatments,were systematically analyzed.Morphological analysis reveals that while both thickαplatelets and coarse priorβgrains impede the spheroidization of lamellar structures,the influence of the former is more pronounced.Variations inαplatelet thickness priorβgrain size exhibit limited impact on the macro-texture type after deformation and annealing.The proportion of low-angle interfaces between the c-axis of the primaryαphase and the<110>direction of the priorβgrains was elevated in rods with thicker platelets compared to thinner ones.展开更多
Influenced by globalization,rural transition in developed Western countries has experienced processes of productivism,post-productivism,and multifunctional development.By contrast,rural transition in most developing c...Influenced by globalization,rural transition in developed Western countries has experienced processes of productivism,post-productivism,and multifunctional development.By contrast,rural transition in most developing countries has been accompanied by rapid urbanization,which has become a core topic in geography research.As the world’s largest developing country,China has undergone profound development since the reform and opening-up.Moreover,rural spaces in some eastern coastal areas have entered the stage of reconstruction after decades of industrialization and urbanization.This paper takes Suzhou as the case area and measures the process of rural transition from 1990 to 2015 by constructing an index system.It then analyzes the characteristics of space-time evolution using exploratory spatial data analysis(ESDA)methods to reveal the influence of economic and social development on rural transition.The results show that rural transition,which generally entails the weakening of rurality and enhancing of urbanity on a macro scale,tends to be heterogeneous across different regions on a micro scale.This paper argues that multifunctionality will be the main future trend of rural transition in rapidly urbanizing areas.The experience in Suzhou could provide an example for establishing policies on sustainable development in rural spaces and achieving urban-rural co-governance.展开更多
Fine-grained rocks（FGR） are the important source rocks and reservoirs of shale hydrocarbon which is the prospect hotspot at present. Widely distributed fine-grained sediments（FGS） of the upper fourth member of Sha...Fine-grained rocks（FGR） are the important source rocks and reservoirs of shale hydrocarbon which is the prospect hotspot at present. Widely distributed fine-grained sediments（FGS） of the upper fourth member of Shahejie Formation in Dongying depression are taken as an example to study the space-time evolution and controlling factor of FGS in this paper. Based on the analysis of well cores, thin sections, inorganic and organic geochemistry indicators, FGR are divided into 7 types of lithofacies. Through the study of ‘point-line-plane＇, this study shows that FGS has the characteristics of rhythum, diversity and succession. The first stage is characterized by clayey FGS（massive claystone）. The second stage is characterized by carbonate FGS（low-TOC laminated limestone） and dolomitic FGS（dolomitic-silty shale） formed by transgression. The third stage is characterized by organic-rich carbonate FGS（middle/high-TOC laminated limestone） distributed in cycle. The fourth stage is characterized by FGS mixed carbonate and siliciclastic sediments（calcareous-silty shale）. A variety of space-time evolution of FGS are controlled by multiple factors including tectonism, climate and lake conditions.展开更多
The shearing/cooling roll （SCR） process was adopted to prepare semi-solid A2017 alloy. The formation and evolution of non-dendritic microstructures in semi-solid A2017 alloy were studied. It is shown that the micros...The shearing/cooling roll （SCR） process was adopted to prepare semi-solid A2017 alloy. The formation and evolution of non-dendritic microstructures in semi-solid A2017 alloy were studied. It is shown that the microstructures of semi-solid billets transform from coarse dendrites into fine equiaxed grains as the pouring temperature of molten alloy decreases o.r roll-shoe cavity height is reduced. From the inlet to the exit of roll-shoe cavity, microstructure of semi-solid slurry near the shoe surface is in the order of coarse dendrites, degenerated dendrites or equiaxed grains, but fine equiaxed grains are near the roll surface. Microstructural evolution of semi-solid slurry prepared by SCR process is that the molten alloy nucleates and grows into dendrite firstly on the roll and shoe＇s surface. Under the shearing and stirring given by the rotating roll, the dendrites crush off and disperse into the melt. Under the shearing and stirring on semi-solid slurry with high volume fraction of solid, the dendrite arms fracture and form equiaxed grain microstructures.展开更多
In this study, the effect of melting temperature on the microstructural evolutions, behavior, and corrosion morphology of Hadfield steel in the casting process is investigated. The mold was prepared by the sodium sili...In this study, the effect of melting temperature on the microstructural evolutions, behavior, and corrosion morphology of Hadfield steel in the casting process is investigated. The mold was prepared by the sodium silicate/CO_2 method, using a blind riser, and then the desired molten steel was obtained using a coreless induction furnace. The casting was performed at melting temperatures of 1350, 1400, 1450, and 1500°C, and the cast blocks were immediately quenched in water. Optical microscopy was used to analyze the microstructure, and scanning electron microscopy(SEM) and X-ray diffractrometry(XRD) were used to analyze the corrosion morphology and phase formation in the microstructure, respectively. The corrosion behavior of the samples was analyzed using a potentiodynamic polarization test and electrochemical impedance spectroscopy(EIS) in 3.5 wt% NaCl. The optical microscopy observations and XRD patterns show that the increase in melting temperature led to a decrease of carbides and an increase in the austenite grain size in the Hadfield steel microstructure. The corrosion tests results show that with increasing melting temperature in the casting process, Hadfield steel shows a higher corrosion resistance. The SEM images of the corrosion morphologies show that the reduction of melting temperature in the Hadfield steel casting process induced micro-galvanic corrosion conditions.展开更多
A molecular dynamics simulation study has been performed for the microstructure evolution in a liquid metal Ni system during crystallization process at two cooling rates by adopting the embedded atom method （EAM） mo...A molecular dynamics simulation study has been performed for the microstructure evolution in a liquid metal Ni system during crystallization process at two cooling rates by adopting the embedded atom method （EAM） model potential. The bond-type index method of Honeycutt-Andersen （HA） and a new cluster-type index method （CTIM-2） have been used to detect and analyse the microstructures in this system. It is demonstrated that the cooling rate plays a critical role in the microstructure evolution： below the crystallization temperature Tc, the effects of cooling rate are very remarkable and can be fully displayed. At different cooling rates of 2.0 × 10^13 K·s^-1 and 1.0 × 10^12 K·s^-1, two different kinds of crystal structures are obtained in the system. The first one is the coexistence of the hcp （expressed by （12 0 0 0 6 6） in CTIM-2） and the fcc （12 0 0 0 12 0） basic clusters consisting of 1421 and 1422 bond-types, and the hcp basic cluster becomes the dominant one with decreasing temperature, the second one is mainly the fcc （12 0 0 0 12 0） basic clusters consisting of 1421 bond-type, and their crystallization temperatures Tc would be 1073 and 1173 K, respectively.展开更多
The microstructural evolution and precipitation behaviour of Nb–V–Mo and single V containing transformation induced plasticity assisted steels were investigated during thermomechanical processing. A plane strain com...The microstructural evolution and precipitation behaviour of Nb–V–Mo and single V containing transformation induced plasticity assisted steels were investigated during thermomechanical processing. A plane strain compression testing machine was used to simulate the thermomechanical processing. Microstructures were characterised by optical microscopy, scanning-transmission electron microscopy and microanalysis, and X-ray diffraction analysis, and Vickers hardness was obtained from the deformed specimens. The resulting microstructure of both Nb–V–Mo and V steels at room temperature primarily consisted of an acicular/bainitic ferrite, retained austenite and martensite surrounded by allotriomorphic ferrite.The TEM analysis showed that a significant number of Nb（V,Mo）（C,N） precipitates were formed in the microstructure down to the finishing stage in Nb–V–Mo steel（i.e. 830℃）. It was also found that the V（C,N）precipitation primarily occurred in both ferrite and deformed austenite below the finishing stage. The results suggested that Nb–Mo additions considerably increased the temperature stability of microalloy precipitates and controlled the microstructural evolution of austenite. However, the microalloy precipitation did not cause a significant precipitation strengthening in both Nb–V–Mo and V steels at room temperature.展开更多
Based on petrological studies of the wall rocks, mineralizing rocks, ores and veins from the Laowangzhai gold deposit, it is discovered that along with the development of silication, carbonation and sulfidation, a kin...Based on petrological studies of the wall rocks, mineralizing rocks, ores and veins from the Laowangzhai gold deposit, it is discovered that along with the development of silication, carbonation and sulfidation, a kind of black opaque ultra-microlite material runs through the spaces between grains, fissures and cleavages. Under observations of the electron microprobe, scanning electronic microscopy and energy spectrum, this kind of ultra-microlite material is confirmed to consist of ultra microcrystalline quartz, silicate, sulfides and carbonates, as well as rutile, scheelite and specularite （magnetite）, showing characters of liquation by the analyses of SEM and energy spectrum. The coexistence of immiscibility and precipitating co-crystallization strongly suggests that the mineralizing fluid changed from the melt to the hydrothermal fluid. Combined with the element geochemical researches, it is realized that the ultra-microlite aggregate is the direct relics of the mantle fluid behaving like a melt and supercritical fluid, which goes along with the mantle-derived magma and will escape from the magma body at a proper time. During the alteration process, the nature of the mantle fluid changed and it is mixed with the crustal fluid, which are favorable for mineralization in the Loawangzhai gold deposit.展开更多
To improve the strength-toughness of traditional U-rib（ TUR） and solve the problem of insufficient penetration between TUR and deckplate,a new local thickened U-rib（ LTUR） has been proposed to improve the fatigue ...To improve the strength-toughness of traditional U-rib（ TUR） and solve the problem of insufficient penetration between TUR and deckplate,a new local thickened U-rib（ LTUR） has been proposed to improve the fatigue resistance of the weld joint under the premise of not increasing thickness and strength of the TUR material. And a hot /warm roll-forming process（ RFP） adopting partially induction heating to 700- 1 000℃ was carried out to fabricate LTUR. The deformation behaviors in the forming process and microstructure of LTUR have been investigated.Mechanical properties and fracture mechanism of the LTUR after hot / warm RFP have been systematically discussed. Moreover,the results are compared with those obtained in cold RFP. Mechanical properties of the LTUR deformed above the critical transformation temperature（ A_（c3）） show high performance characteristics with marked fatigue resistance and superior toughness. Upon increasing the heating temperature from 700 to 900 ℃,the initial coarse ferrite-pearlite structure transform into equiaxed ultrafine ferrite（ 1- 3 μm） and precipitates such as（ Nb,Ti）（ C,N） are uniformly distributed in the matrix. The average dislocation density of the specimens after hot rollforming at heating temperature of 900 ℃ decreases dramatically compared with those of the specimens subjected to the cold RFP. Furthermore,a typical characteristic of ductile fracture mechanism and the high impact energy are more convinced that the specimens deformed above 900 ℃ have obtained an optimal combination of strength and toughness.展开更多
Structure evolution of an Al-Zn wrought alloy in remelting processing in thestrain induced melt activated (SIMA) serai-solid procedure was observed, and effects of factors, theremelting temperature, the holding time, ...Structure evolution of an Al-Zn wrought alloy in remelting processing in thestrain induced melt activated (SIMA) serai-solid procedure was observed, and effects of factors, theremelting temperature, the holding time, and the compression strain, on structures and grain sizesof the alloy were investigated. The results show that (1) the proper temperature of remelting is inthe range of 610 to 615℃; (2) the grain size in specimen with greater compression strain is smallerthan that with smaller compression strain in condition of the same remelting temperature andholding time, and the grain size in local area with great local equivalent strain is smaller thanthat with small one; (3) liquid occurs in form of cluster in matrix during remelting and itsquantity increases with remelting time increasing; liquid in specimen with great compression strainoccurs earlier than that with small one, and quantity of liquid in the center of specimen withgreater local equivalent strain is greater than that in the two ends of it; (4) distortion energyafter deforming in matrix of the alloy is the significant factor to activate melting of matrix atlocal area with great local equivalent strain.展开更多
High strength β titanium alloys are widely used in large load bearing components in the aerospace field. At present, large parts are generally formed by die forging. Different initial microstructures and deformation ...High strength β titanium alloys are widely used in large load bearing components in the aerospace field. At present, large parts are generally formed by die forging. Different initial microstructures and deformation process parameters will significantly affect the flow behavior. To precisely control the microstructures, researchers have conducted many studies to analyze the microstructure evolution law and deformation mechanism during hot compression. This review focuses on the microstructure evolution of high strength β titanium alloys during hot deformation, including dynamic recrystallization and dynamic recovery in the single-phase region and the dynamic evolution of the α phase in the two-phase region. Furthermore, the optimal hot processing regions, instability regions,and the relationship between the efficiency of power dissipation and the deformation mechanism in the hot processing map are summarized. Finally, the problems and development direction of using hot processing maps to optimize process parameters are also emphasized.展开更多
The Jiama deposit is a large copper deposit in Tibet. Mineralization occurs in three different host rocks： skarn, hornfels and porphyry. A detailed fluid inclusion study was conducted for veins in the different host ...The Jiama deposit is a large copper deposit in Tibet. Mineralization occurs in three different host rocks： skarn, hornfels and porphyry. A detailed fluid inclusion study was conducted for veins in the different host rocks to investigate the relationship between fluid evolution and ore-forming processes. Based on examination of cores from 36 drill holes, three types of veins （A, B and D） were identified in the porphyries, four types （I, II, III and IV） in the skarn, and three （a, b and c） in the hornfels. The crosscutting relationships of the veins and that of the host rocks suggest two hydrothermal stages, one early and one late stage. Fluid inclusions indicate that the Jiama hydrothermal fluid system underwent at least two episodes of fluid boiling. The first boiling event occurred during the early hydrothermal stage, as recorded by fluid inclusions hosted in type A veins in the porphyries, type a veins in the hornfels, and wollastonite in the skarns. This fluid boiling event was associated with relatively weak mineralization. The second boiling event occurred in the late hydrothermal stage, as determined from fluid inclusions hosted in type B and D veins in the porphyries, type I to IV veins in the skarns, and type b and c veins in the hornfels. This late boiling event, together with mixing with meteoric water, was responsible for more than 90% of the metal accumulation in the deposit. The first boiling only occurred in the central part of the deposit and the second boiling event took place across an entire interlayered structural zone between hornfels and marble. A spatial zoning of ore-elements is evident, and appears to be related to different migration pathways and precipitation temperatures of Cu, Mo, Pb, Zn, Au and Ag.展开更多
The hot deformation behavior of Al-Cu-Li alloy was investigated by hot compression tests in the temperature range of 340-500℃ with strain rate of 0.001-10.000 s^(-1).Based on the dynamic materials model(DMM),processi...The hot deformation behavior of Al-Cu-Li alloy was investigated by hot compression tests in the temperature range of 340-500℃ with strain rate of 0.001-10.000 s^(-1).Based on the dynamic materials model(DMM),processing maps of the test alloy were developed for optimizing hot processing parameters.The optimum parameters of hot deformation for Al-Cu-Li alloy are at temperature of 400-430℃and strain rate of about 0.100 s^(-1),with efficiency of power dissipation of around 30%.The microstructural manifestation of the alloy deformed in instability domains is flow localization,and dynamic softening first occurs in flow localizations structure.In stable domains,dynamic recovery(DRV) and dynamic recrystallization(DRX) are the main microstructural evolution mechanism.DRX is gradually strengthened with the increase in deformation temperature and the decrease in strain rate.During hot deformation,the DRX mechanism of Al-Cu-Li alloy is dominated by continuous DRX(CDRX).A DRX model of Al-Cu-Li alloy is proposed based on the microstructural evolution process of the test alloy.展开更多
Ultralight Mg-Li alloys offer promising applications across various fields.Mg-Li alloys enriched with Al and Zn hold theoretical potential for achieving excellent mechanical strength and corrosion resistance.However,t...Ultralight Mg-Li alloys offer promising applications across various fields.Mg-Li alloys enriched with Al and Zn hold theoretical potential for achieving excellent mechanical strength and corrosion resistance.However,the structural and performance characteristics of such Mg-Li alloys,particularly after thermo-mechanical processing,remain inadequately explored and understood.This study investigated the mi-crostructural evolution of a Mg-9Li-5Al-4Zn alloy after friction stir processing and its consequent effects on the mechanical and corrosion performance.The grain size of the alloy was effectively refined and sta-bilized during friction stir processing at various heat inputs.The yield strength of the alloy increased by 86.4%after friction stir processing under the highest heat input condition,which was attributed to fine grain strengthening,solid solution strengthening and dispersion strengthening.Concurrently,the alloy ex-perienced a slight decrease in elongation after the friction stir processing.The alloy subjected to friction stir processing with the highest heat input exhibited a minimal corrosion current density of 6.10×10^(−6) A/cm^(2),which was only 25%of the base metal.The enhanced anti-corrosion properties can be attributed to the dispersion and distribution of precipitated particles induced by friction stir processing,which hin-dered the micro-galvanic corrosion and promoted the generation of a compact surface film,leading to minimal and uniform corrosion.This investigation can be significant for understanding the metallurgical mechanisms and performance evolution of Mg-Li alloys during thermomechanical processes.展开更多
The effects of electropulsing-assisted ultrasonic surface rolling process on surface mechanical properties andmicrostructure evolution of commercial pure titanium were investigated. It was found that the surface mecha...The effects of electropulsing-assisted ultrasonic surface rolling process on surface mechanical properties andmicrostructure evolution of commercial pure titanium were investigated. It was found that the surface mechanical prop-erties were significantly enhanced compared to traditional ultrasonic surface rolling process （USRP）, leading to smallersurface roughness and smoother morphology with fewer cracks and defects. Moreover, surface strengthened layer wasremarkably enhanced with deeper severe plastic deformation layer and higher surface hardness. Remarkable enhancementsof surface mechanical properties may be related to the gradient refined microstructure, the enhanced severe plasticdeformation layer and the accelerated formation of sub-boundaries and twins induced by coupling effects of USRP andelectropulsing. The primary intrinsic reasons for these improvements may be attributed to the thermal and athermal effectscaused by electropulsing treatment, which would accelerate dislocation mobility and atom diffusion.展开更多
Abstract: Thermochronological dating was used to study the thermal evolution of the Mesozoic plutons and uplift history of the Yanshan orogenic belt. The results show that the cooling history of the plutons is complic...Abstract: Thermochronological dating was used to study the thermal evolution of the Mesozoic plutons and uplift history of the Yanshan orogenic belt. The results show that the cooling history of the plutons is complicated, corresponding to the inhomogeneous uplift process of the Yanshan orogenic belt. The Panshan granite cooled fast during 226.48–204.95 Ma at a rate of 10.22°C/Ma after its emplacement at a depth of about 10 km, and its fast uplift occurred in about 96–35 Ma at an average rate of 0.115 mm/a. The Wulingshan pluton cooled fast during 132–127.23 Ma at a rate of 94.34°C/Ma, and its rapid uplift occurred in 86–45 Ma at an average rate of 0.186 mm/a. The Yunmengshan granite cooled fast during 143–120.99 Ma at a rate of 19.51°C/Ma, and its rapid uplift occurred in 106–103.95 Ma and 20–0.0 Ma at a rate of 1.06 mm/a and 0.15 mm/a respectively. The Sihetang granite-gneiss uplifted rapidly since 13 Ma at an average rate of 0.256 mm/a. The Badaling granite uplifted rapidly since 6 Ma at an average rate of 0.556 mm/a. The Cenozoic uplift of the Yanshan Mountains can be well correlated to the rifting process of the surrounding basins.展开更多
As-cast Mg-6Zn-xCu-0.6Zr(x=0,0.5,1.0,wt.%)alloys were fabricated by permanent mold casting;then,the alloys were subjected to homogenization heat treatment and extrusion-shearing(ES)process.The microstructure and mecha...As-cast Mg-6Zn-xCu-0.6Zr(x=0,0.5,1.0,wt.%)alloys were fabricated by permanent mold casting;then,the alloys were subjected to homogenization heat treatment and extrusion-shearing(ES)process.The microstructure and mechanical properties of the alloys were evaluated by OM,SEM/EDS,XRD,TEM,EBSD and tensile tests.The results show that the hard MgZnCu phase in Cu-added alloy can strengthen particle-stimulated nucleation(PSN)effect and hinder the migration of dynamic recrystallization(DRX)grain boundary at an elevated temperature during ES.The ZK60+0.5Cu alloy shows an optimal tensile strength–ductility combination(UTS of 396 MPa,YS of 313 MPa,andδ=20.3%)owing to strong grain boundary strengthening and improvement of Schmid factor for{0001}■basal slip.The aggregation of microvoids around the MgZnCu phase mainly accounts for the lower tensile elongation of ZK60+1.0Cu alloy compared with ZK60 alloy.展开更多
In the application of high-pressure water jet assisted breaking of deep underground rock engineering,the influence mechanism of rock temperature on the rock fragmentation process under jet action is still unclear.Ther...In the application of high-pressure water jet assisted breaking of deep underground rock engineering,the influence mechanism of rock temperature on the rock fragmentation process under jet action is still unclear.Therefore,the fluid evolution characteristics and rock fracture behavior during jet impingement were studied.The results indicate that the breaking process of high-temperature rock by jet impact can be divided into four stages:initial fluid-solid contact stage,intense thermal exchange stage,perforation and fracturing stage,and crack propagation and penetration stage.With the increase of rock temperature,the jet reflection angles and the time required for complete cooling of the impact surface significantly decrease,while the number of cracks and crack propagation rate significantly increase,and the rock breaking critical time is shortened by up to 34.5%.Based on numerical simulation results,it was found that the center temperature of granite at 400℃ rapidly decreased from 390 to 260℃ within 0.7 s under jet impact.In addition,a critical temperature and critical heat flux prediction model considering the staged breaking of hot rocks was established.These findings provide valuable insights to guide the water jet technology assisted deep ground hot rock excavation project.展开更多
基金the National Key Research and Development Program of China(No.2016YFB0700505)the National Natural Science Foundation of China(No.51571020).
文摘The hot deformation behavior of GH3230 superalloy under selected deformation conditions ranging from 950 to 1150℃with strain rates ranging from 0.01 to 10 s^(–1)was studied through isothermal hot compression experiments.Based on the obtained flow stresses,a strain-compensated Arrhenius-type model was developed for the description of hot deformation behavior,and the consistency of the predicted flow stresses with the experimental values confirms the accuracy of the developed model.Furthermore,the processing maps were constructed and classified into the instability domain,low-dissipation stability domain and high-dissipation stability domain in accordance with the dynamic material model and the instability criterion.Microstructure observations indicated that the instability domain exhibits the adiabatic shear bands formation,and the low-power dissipation domain exhibits partial dynamic recrystallization(DRX),with the temperature increase/strain rate decrease being favorable for the DRX.The high-dissipation stability domain was occupied by uniformly fine equiaxed grains,and was identified as the optimal processing window,which corresponds to the deformation conditions at 1070–1150℃ with strain rates ranging from 0.01 to 0.15 s^(–1).Moreover,various DRX mechanisms are observed to occur during the hot deformation,which include the discontinuous dynamic recrystallization,characterized by nucleation at bulged boundaries,the continuous dynamic recrystallization with subgrain progressive rotation and the particle stimulated nucleation mechanism with stimulated nucleation of carbide particles.
基金supported by the National Natural Science Foundation of China(No.52205393)the Natural Science Foundation of Shandong Province,China(No.ZR2022QE263)+1 种基金the Science and Technology Commission of Shanghai Municipality,Shanghai Rising-Star Program,China(No.23YF1413900)the Science and Technology Innovation Plan of Shanghai Science and Technology Commission,China(Nos.21010500800,23010501100).
文摘The microstructure and texture evolutions during extrusion and rolling processes of the 2195 Al−Li alloy were investigated.The EBSD technique was employed to reveal the microscopic evolution mechanisms of different texture components.The findings reveal that the texture evolution is governed by two mechanisms:an overall orientation transformation induced by plastic strain and a localized transformation occurring at the shearing bands within grains.During the rolling process,the extrusion texture components of Ex{123}<111>and Cu{112}<111>evolve into S{123}<634>,and the Bs{011}<211>rotates into the orientations near R-Bs and S.With increasing deformation,the S,Bs,and R-Bs orientations further rotate around the TD axis and disperse into new orientations,forming recrystallized grains.The shearing bands with different initial orientations exhibit similar orientation evolution patterns,all of which evolve from the initial orientation to a series of recrystallization orientations.
基金supported by the National Science and Technology Major Project(No.J2019-VI-0012-0126).
文摘The initial microstructure of titanium alloy in theα+βphase region is pivotal in dictating the performance of the final products after thermomechanical processing.Microstructures and textures of three rods,each prepared through distinct pretreatments,were systematically analyzed.Morphological analysis reveals that while both thickαplatelets and coarse priorβgrains impede the spheroidization of lamellar structures,the influence of the former is more pronounced.Variations inαplatelet thickness priorβgrain size exhibit limited impact on the macro-texture type after deformation and annealing.The proportion of low-angle interfaces between the c-axis of the primaryαphase and the<110>direction of the priorβgrains was elevated in rods with thicker platelets compared to thinner ones.
基金National Social Science Foundation of China,No.21FSHB014National Natural Science Foundation of China,No.42001196。
文摘Influenced by globalization,rural transition in developed Western countries has experienced processes of productivism,post-productivism,and multifunctional development.By contrast,rural transition in most developing countries has been accompanied by rapid urbanization,which has become a core topic in geography research.As the world’s largest developing country,China has undergone profound development since the reform and opening-up.Moreover,rural spaces in some eastern coastal areas have entered the stage of reconstruction after decades of industrialization and urbanization.This paper takes Suzhou as the case area and measures the process of rural transition from 1990 to 2015 by constructing an index system.It then analyzes the characteristics of space-time evolution using exploratory spatial data analysis(ESDA)methods to reveal the influence of economic and social development on rural transition.The results show that rural transition,which generally entails the weakening of rurality and enhancing of urbanity on a macro scale,tends to be heterogeneous across different regions on a micro scale.This paper argues that multifunctionality will be the main future trend of rural transition in rapidly urbanizing areas.The experience in Suzhou could provide an example for establishing policies on sustainable development in rural spaces and achieving urban-rural co-governance.
基金supported by the National Science and Technology Special Grant of China (No. 2017zx05036-004)
文摘Fine-grained rocks（FGR） are the important source rocks and reservoirs of shale hydrocarbon which is the prospect hotspot at present. Widely distributed fine-grained sediments（FGS） of the upper fourth member of Shahejie Formation in Dongying depression are taken as an example to study the space-time evolution and controlling factor of FGS in this paper. Based on the analysis of well cores, thin sections, inorganic and organic geochemistry indicators, FGR are divided into 7 types of lithofacies. Through the study of ‘point-line-plane＇, this study shows that FGS has the characteristics of rhythum, diversity and succession. The first stage is characterized by clayey FGS（massive claystone）. The second stage is characterized by carbonate FGS（low-TOC laminated limestone） and dolomitic FGS（dolomitic-silty shale） formed by transgression. The third stage is characterized by organic-rich carbonate FGS（middle/high-TOC laminated limestone） distributed in cycle. The fourth stage is characterized by FGS mixed carbonate and siliciclastic sediments（calcareous-silty shale）. A variety of space-time evolution of FGS are controlled by multiple factors including tectonism, climate and lake conditions.
基金The authors would like to thank the National Natural Science Foundation of China and Baoshan Iron&Steel Co.of Shanghai for financial support under the grant No.50274020.
文摘The shearing/cooling roll （SCR） process was adopted to prepare semi-solid A2017 alloy. The formation and evolution of non-dendritic microstructures in semi-solid A2017 alloy were studied. It is shown that the microstructures of semi-solid billets transform from coarse dendrites into fine equiaxed grains as the pouring temperature of molten alloy decreases o.r roll-shoe cavity height is reduced. From the inlet to the exit of roll-shoe cavity, microstructure of semi-solid slurry near the shoe surface is in the order of coarse dendrites, degenerated dendrites or equiaxed grains, but fine equiaxed grains are near the roll surface. Microstructural evolution of semi-solid slurry prepared by SCR process is that the molten alloy nucleates and grows into dendrite firstly on the roll and shoe＇s surface. Under the shearing and stirring given by the rotating roll, the dendrites crush off and disperse into the melt. Under the shearing and stirring on semi-solid slurry with high volume fraction of solid, the dendrite arms fracture and form equiaxed grain microstructures.
文摘In this study, the effect of melting temperature on the microstructural evolutions, behavior, and corrosion morphology of Hadfield steel in the casting process is investigated. The mold was prepared by the sodium silicate/CO_2 method, using a blind riser, and then the desired molten steel was obtained using a coreless induction furnace. The casting was performed at melting temperatures of 1350, 1400, 1450, and 1500°C, and the cast blocks were immediately quenched in water. Optical microscopy was used to analyze the microstructure, and scanning electron microscopy(SEM) and X-ray diffractrometry(XRD) were used to analyze the corrosion morphology and phase formation in the microstructure, respectively. The corrosion behavior of the samples was analyzed using a potentiodynamic polarization test and electrochemical impedance spectroscopy(EIS) in 3.5 wt% NaCl. The optical microscopy observations and XRD patterns show that the increase in melting temperature led to a decrease of carbides and an increase in the austenite grain size in the Hadfield steel microstructure. The corrosion tests results show that with increasing melting temperature in the casting process, Hadfield steel shows a higher corrosion resistance. The SEM images of the corrosion morphologies show that the reduction of melting temperature in the Hadfield steel casting process induced micro-galvanic corrosion conditions.
基金Project supported by the National Natural Science Foundation of China （Grant Nos 50271026 and 50571037）.
文摘A molecular dynamics simulation study has been performed for the microstructure evolution in a liquid metal Ni system during crystallization process at two cooling rates by adopting the embedded atom method （EAM） model potential. The bond-type index method of Honeycutt-Andersen （HA） and a new cluster-type index method （CTIM-2） have been used to detect and analyse the microstructures in this system. It is demonstrated that the cooling rate plays a critical role in the microstructure evolution： below the crystallization temperature Tc, the effects of cooling rate are very remarkable and can be fully displayed. At different cooling rates of 2.0 × 10^13 K·s^-1 and 1.0 × 10^12 K·s^-1, two different kinds of crystal structures are obtained in the system. The first one is the coexistence of the hcp （expressed by （12 0 0 0 6 6） in CTIM-2） and the fcc （12 0 0 0 12 0） basic clusters consisting of 1421 and 1422 bond-types, and the hcp basic cluster becomes the dominant one with decreasing temperature, the second one is mainly the fcc （12 0 0 0 12 0） basic clusters consisting of 1421 bond-type, and their crystallization temperatures Tc would be 1073 and 1173 K, respectively.
文摘The microstructural evolution and precipitation behaviour of Nb–V–Mo and single V containing transformation induced plasticity assisted steels were investigated during thermomechanical processing. A plane strain compression testing machine was used to simulate the thermomechanical processing. Microstructures were characterised by optical microscopy, scanning-transmission electron microscopy and microanalysis, and X-ray diffraction analysis, and Vickers hardness was obtained from the deformed specimens. The resulting microstructure of both Nb–V–Mo and V steels at room temperature primarily consisted of an acicular/bainitic ferrite, retained austenite and martensite surrounded by allotriomorphic ferrite.The TEM analysis showed that a significant number of Nb（V,Mo）（C,N） precipitates were formed in the microstructure down to the finishing stage in Nb–V–Mo steel（i.e. 830℃）. It was also found that the V（C,N）precipitation primarily occurred in both ferrite and deformed austenite below the finishing stage. The results suggested that Nb–Mo additions considerably increased the temperature stability of microalloy precipitates and controlled the microstructural evolution of austenite. However, the microalloy precipitation did not cause a significant precipitation strengthening in both Nb–V–Mo and V steels at room temperature.
基金supported by the National Natural Science Foundation of China (Grants No. 40473027 and 40773031)the Foundation of Doctoral Supported by the Ministry of Education (20105122110010 and 20115122110005)+1 种基金the Foundation of Open Subjects of State Key Laboratory for Mineral Deposits Research,Nanjing University (14-08-3)the Project of the State Key(Preparation Support) Disciplines of Mineralogy,Petrology and Mineral Deposit Geology of Sichuan Province (SZD0407)
文摘Based on petrological studies of the wall rocks, mineralizing rocks, ores and veins from the Laowangzhai gold deposit, it is discovered that along with the development of silication, carbonation and sulfidation, a kind of black opaque ultra-microlite material runs through the spaces between grains, fissures and cleavages. Under observations of the electron microprobe, scanning electronic microscopy and energy spectrum, this kind of ultra-microlite material is confirmed to consist of ultra microcrystalline quartz, silicate, sulfides and carbonates, as well as rutile, scheelite and specularite （magnetite）, showing characters of liquation by the analyses of SEM and energy spectrum. The coexistence of immiscibility and precipitating co-crystallization strongly suggests that the mineralizing fluid changed from the melt to the hydrothermal fluid. Combined with the element geochemical researches, it is realized that the ultra-microlite aggregate is the direct relics of the mantle fluid behaving like a melt and supercritical fluid, which goes along with the mantle-derived magma and will escape from the magma body at a proper time. During the alteration process, the nature of the mantle fluid changed and it is mixed with the crustal fluid, which are favorable for mineralization in the Loawangzhai gold deposit.
文摘To improve the strength-toughness of traditional U-rib（ TUR） and solve the problem of insufficient penetration between TUR and deckplate,a new local thickened U-rib（ LTUR） has been proposed to improve the fatigue resistance of the weld joint under the premise of not increasing thickness and strength of the TUR material. And a hot /warm roll-forming process（ RFP） adopting partially induction heating to 700- 1 000℃ was carried out to fabricate LTUR. The deformation behaviors in the forming process and microstructure of LTUR have been investigated.Mechanical properties and fracture mechanism of the LTUR after hot / warm RFP have been systematically discussed. Moreover,the results are compared with those obtained in cold RFP. Mechanical properties of the LTUR deformed above the critical transformation temperature（ A_（c3）） show high performance characteristics with marked fatigue resistance and superior toughness. Upon increasing the heating temperature from 700 to 900 ℃,the initial coarse ferrite-pearlite structure transform into equiaxed ultrafine ferrite（ 1- 3 μm） and precipitates such as（ Nb,Ti）（ C,N） are uniformly distributed in the matrix. The average dislocation density of the specimens after hot rollforming at heating temperature of 900 ℃ decreases dramatically compared with those of the specimens subjected to the cold RFP. Furthermore,a typical characteristic of ductile fracture mechanism and the high impact energy are more convinced that the specimens deformed above 900 ℃ have obtained an optimal combination of strength and toughness.
文摘Structure evolution of an Al-Zn wrought alloy in remelting processing in thestrain induced melt activated (SIMA) serai-solid procedure was observed, and effects of factors, theremelting temperature, the holding time, and the compression strain, on structures and grain sizesof the alloy were investigated. The results show that (1) the proper temperature of remelting is inthe range of 610 to 615℃; (2) the grain size in specimen with greater compression strain is smallerthan that with smaller compression strain in condition of the same remelting temperature andholding time, and the grain size in local area with great local equivalent strain is smaller thanthat with small one; (3) liquid occurs in form of cluster in matrix during remelting and itsquantity increases with remelting time increasing; liquid in specimen with great compression strainoccurs earlier than that with small one, and quantity of liquid in the center of specimen withgreater local equivalent strain is greater than that in the two ends of it; (4) distortion energyafter deforming in matrix of the alloy is the significant factor to activate melting of matrix atlocal area with great local equivalent strain.
基金supported by the Project of National Key Laboratory for Precision Hot Processing of Metals, Harbin Institute of Technology, China (No. 6142909190207)Shaanxi Key Laboratory of High-performance Precision Forming Technology and Equipment (SKL-HPFTE), China (No. PETE-2019-KF-01)。
文摘High strength β titanium alloys are widely used in large load bearing components in the aerospace field. At present, large parts are generally formed by die forging. Different initial microstructures and deformation process parameters will significantly affect the flow behavior. To precisely control the microstructures, researchers have conducted many studies to analyze the microstructure evolution law and deformation mechanism during hot compression. This review focuses on the microstructure evolution of high strength β titanium alloys during hot deformation, including dynamic recrystallization and dynamic recovery in the single-phase region and the dynamic evolution of the α phase in the two-phase region. Furthermore, the optimal hot processing regions, instability regions,and the relationship between the efficiency of power dissipation and the deformation mechanism in the hot processing map are summarized. Finally, the problems and development direction of using hot processing maps to optimize process parameters are also emphasized.
基金funded by the third subject of National Natural Science Foundation of China(41302060)Geological Survey Project(12120114001304,121201004000150012)
文摘The Jiama deposit is a large copper deposit in Tibet. Mineralization occurs in three different host rocks： skarn, hornfels and porphyry. A detailed fluid inclusion study was conducted for veins in the different host rocks to investigate the relationship between fluid evolution and ore-forming processes. Based on examination of cores from 36 drill holes, three types of veins （A, B and D） were identified in the porphyries, four types （I, II, III and IV） in the skarn, and three （a, b and c） in the hornfels. The crosscutting relationships of the veins and that of the host rocks suggest two hydrothermal stages, one early and one late stage. Fluid inclusions indicate that the Jiama hydrothermal fluid system underwent at least two episodes of fluid boiling. The first boiling event occurred during the early hydrothermal stage, as recorded by fluid inclusions hosted in type A veins in the porphyries, type a veins in the hornfels, and wollastonite in the skarns. This fluid boiling event was associated with relatively weak mineralization. The second boiling event occurred in the late hydrothermal stage, as determined from fluid inclusions hosted in type B and D veins in the porphyries, type I to IV veins in the skarns, and type b and c veins in the hornfels. This late boiling event, together with mixing with meteoric water, was responsible for more than 90% of the metal accumulation in the deposit. The first boiling only occurred in the central part of the deposit and the second boiling event took place across an entire interlayered structural zone between hornfels and marble. A spatial zoning of ore-elements is evident, and appears to be related to different migration pathways and precipitation temperatures of Cu, Mo, Pb, Zn, Au and Ag.
基金financially supported by the National Program on Key Basic Research Project of China (No.2012CB619504)the National Natural Science Foundation of China (No.51274046)
文摘The hot deformation behavior of Al-Cu-Li alloy was investigated by hot compression tests in the temperature range of 340-500℃ with strain rate of 0.001-10.000 s^(-1).Based on the dynamic materials model(DMM),processing maps of the test alloy were developed for optimizing hot processing parameters.The optimum parameters of hot deformation for Al-Cu-Li alloy are at temperature of 400-430℃and strain rate of about 0.100 s^(-1),with efficiency of power dissipation of around 30%.The microstructural manifestation of the alloy deformed in instability domains is flow localization,and dynamic softening first occurs in flow localizations structure.In stable domains,dynamic recovery(DRV) and dynamic recrystallization(DRX) are the main microstructural evolution mechanism.DRX is gradually strengthened with the increase in deformation temperature and the decrease in strain rate.During hot deformation,the DRX mechanism of Al-Cu-Li alloy is dominated by continuous DRX(CDRX).A DRX model of Al-Cu-Li alloy is proposed based on the microstructural evolution process of the test alloy.
基金supported by the National Natural Science Foundation of China(grant Nos.U23A20541 and 52305385).
文摘Ultralight Mg-Li alloys offer promising applications across various fields.Mg-Li alloys enriched with Al and Zn hold theoretical potential for achieving excellent mechanical strength and corrosion resistance.However,the structural and performance characteristics of such Mg-Li alloys,particularly after thermo-mechanical processing,remain inadequately explored and understood.This study investigated the mi-crostructural evolution of a Mg-9Li-5Al-4Zn alloy after friction stir processing and its consequent effects on the mechanical and corrosion performance.The grain size of the alloy was effectively refined and sta-bilized during friction stir processing at various heat inputs.The yield strength of the alloy increased by 86.4%after friction stir processing under the highest heat input condition,which was attributed to fine grain strengthening,solid solution strengthening and dispersion strengthening.Concurrently,the alloy ex-perienced a slight decrease in elongation after the friction stir processing.The alloy subjected to friction stir processing with the highest heat input exhibited a minimal corrosion current density of 6.10×10^(−6) A/cm^(2),which was only 25%of the base metal.The enhanced anti-corrosion properties can be attributed to the dispersion and distribution of precipitated particles induced by friction stir processing,which hin-dered the micro-galvanic corrosion and promoted the generation of a compact surface film,leading to minimal and uniform corrosion.This investigation can be significant for understanding the metallurgical mechanisms and performance evolution of Mg-Li alloys during thermomechanical processes.
基金financial support from the Shenzhen Development and Reform Commission Engineering Laboratory Project(Shenzhen development and Reform2015-1033)the Shenzhen Science and Technology supporting Plan Project(GJHS20160331183313435)the China Postdoctoral Science Foundation(No.2017M620770)
文摘The effects of electropulsing-assisted ultrasonic surface rolling process on surface mechanical properties andmicrostructure evolution of commercial pure titanium were investigated. It was found that the surface mechanical prop-erties were significantly enhanced compared to traditional ultrasonic surface rolling process （USRP）, leading to smallersurface roughness and smoother morphology with fewer cracks and defects. Moreover, surface strengthened layer wasremarkably enhanced with deeper severe plastic deformation layer and higher surface hardness. Remarkable enhancementsof surface mechanical properties may be related to the gradient refined microstructure, the enhanced severe plasticdeformation layer and the accelerated formation of sub-boundaries and twins induced by coupling effects of USRP andelectropulsing. The primary intrinsic reasons for these improvements may be attributed to the thermal and athermal effectscaused by electropulsing treatment, which would accelerate dislocation mobility and atom diffusion.
文摘Abstract: Thermochronological dating was used to study the thermal evolution of the Mesozoic plutons and uplift history of the Yanshan orogenic belt. The results show that the cooling history of the plutons is complicated, corresponding to the inhomogeneous uplift process of the Yanshan orogenic belt. The Panshan granite cooled fast during 226.48–204.95 Ma at a rate of 10.22°C/Ma after its emplacement at a depth of about 10 km, and its fast uplift occurred in about 96–35 Ma at an average rate of 0.115 mm/a. The Wulingshan pluton cooled fast during 132–127.23 Ma at a rate of 94.34°C/Ma, and its rapid uplift occurred in 86–45 Ma at an average rate of 0.186 mm/a. The Yunmengshan granite cooled fast during 143–120.99 Ma at a rate of 19.51°C/Ma, and its rapid uplift occurred in 106–103.95 Ma and 20–0.0 Ma at a rate of 1.06 mm/a and 0.15 mm/a respectively. The Sihetang granite-gneiss uplifted rapidly since 13 Ma at an average rate of 0.256 mm/a. The Badaling granite uplifted rapidly since 6 Ma at an average rate of 0.556 mm/a. The Cenozoic uplift of the Yanshan Mountains can be well correlated to the rifting process of the surrounding basins.
基金Project(XLYC1807021)supported by Liaoning Revitalization Talents Program,ChinaProject(2019JH3/30100014)supported by Joint Research Fund of Lianning-Shenyang National Laboratory for Materials Science,China+2 种基金Project supported by Liaoning Bai Qian Wan Talents Program,ChinaProject(RC200414)supported by Innovation Talent Program in Sciences and Technologies for Young and Middle-aged Scientists of Shenyang City,ChinaProject(XLYC1908006)supported by High Level Innovation Team of Liaoning Province,China。
文摘As-cast Mg-6Zn-xCu-0.6Zr(x=0,0.5,1.0,wt.%)alloys were fabricated by permanent mold casting;then,the alloys were subjected to homogenization heat treatment and extrusion-shearing(ES)process.The microstructure and mechanical properties of the alloys were evaluated by OM,SEM/EDS,XRD,TEM,EBSD and tensile tests.The results show that the hard MgZnCu phase in Cu-added alloy can strengthen particle-stimulated nucleation(PSN)effect and hinder the migration of dynamic recrystallization(DRX)grain boundary at an elevated temperature during ES.The ZK60+0.5Cu alloy shows an optimal tensile strength–ductility combination(UTS of 396 MPa,YS of 313 MPa,andδ=20.3%)owing to strong grain boundary strengthening and improvement of Schmid factor for{0001}■basal slip.The aggregation of microvoids around the MgZnCu phase mainly accounts for the lower tensile elongation of ZK60+1.0Cu alloy compared with ZK60 alloy.
基金supported by National Natural Science Foundation of China (No.U23A20597)National Major Science and Technology Project of China (No.2024ZD1003803)+1 种基金Chongqing Science Fund for Distinguished Young Scholars of Chongqing Municipality (No.CSTB2022NSCQ-JQX0028)Natural Science Foundation of Chongqing (No.CSTB2024NSCQ-MSX0503)。
文摘In the application of high-pressure water jet assisted breaking of deep underground rock engineering,the influence mechanism of rock temperature on the rock fragmentation process under jet action is still unclear.Therefore,the fluid evolution characteristics and rock fracture behavior during jet impingement were studied.The results indicate that the breaking process of high-temperature rock by jet impact can be divided into four stages:initial fluid-solid contact stage,intense thermal exchange stage,perforation and fracturing stage,and crack propagation and penetration stage.With the increase of rock temperature,the jet reflection angles and the time required for complete cooling of the impact surface significantly decrease,while the number of cracks and crack propagation rate significantly increase,and the rock breaking critical time is shortened by up to 34.5%.Based on numerical simulation results,it was found that the center temperature of granite at 400℃ rapidly decreased from 390 to 260℃ within 0.7 s under jet impact.In addition,a critical temperature and critical heat flux prediction model considering the staged breaking of hot rocks was established.These findings provide valuable insights to guide the water jet technology assisted deep ground hot rock excavation project.
