High-temperature and short-time(HTST)solution heat treatment combined with non-isothermal aging(NIA)was employed to regulate the microstructure and properties of Al−4.5Mg−2.0Zn−0.3Ag alloy.Results indicate that HTST s...High-temperature and short-time(HTST)solution heat treatment combined with non-isothermal aging(NIA)was employed to regulate the microstructure and properties of Al−4.5Mg−2.0Zn−0.3Ag alloy.Results indicate that HTST solution heat treatment can not only retain partial deformation dislocations,but inhibit the recrystallization behavior and increase the proportion of low-angle grain boundaries(LAGBs).In the subsequent NIA process,HTST solution heat treatment combined with NIA is instrumental in restraining the degradation of dislocations and promoting precipitation of nano-scale T'-Mg_(32)(Al,Zn,Ag)49 phase,which improves the strength of the alloy greatly.In addition,a higher fraction of LAGBs and the discontinuous distribution of grain boundary precipitates caused by this novel technology meliorate the corrosion resistance of Al−4.5Mg−2.0Zn−0.3Ag alloy.展开更多
An effort to obtain superior impact properties for Al-7Si-0.35 Mg alloy is presented,where modification with 0.02 wt% Sr and 0.1 wt% La as well as solution treatment was jointly employed.The samples were solution trea...An effort to obtain superior impact properties for Al-7Si-0.35 Mg alloy is presented,where modification with 0.02 wt% Sr and 0.1 wt% La as well as solution treatment was jointly employed.The samples were solution treated at 535℃ for 15 min to 12 h.The microstructure,fracture mechanism,and their correlation with the impact properties of the alloy were studied in detail mainly through optical microscopy(OM),scanning electron microscopy(SEM) and oscillography impact test.The results show that the addition of Sr and La refined the eutectic Si particles significantly from~ 2.05 μm(modified with Sr alone) to~ 0.75 μm in as-cast microstructure,leading to a very homogeneous distribution of spheroidized Si particles in the alloy solution treated at 535℃ for 8 h.The alloy exhibits excellent impact toughness up to 75 J·cm^(-2),which is much higher than the maximum impact toughness of the alloys modified by Sr alone(~ 46 J·cm^(-2)).The major reason for this remarkable increase in the impact property is the dramatic increase in crack initiation energy.The dispersoid-free zones(DFZs)near the eutectic regions mainly consist of the ductile Al-matrix,which exhibits excellent ductility.The ductile Al-matrix of the DFZs hinders the crack propagation,resulting in a significant increase in crack propagation energy.展开更多
Zn-Li alloys are considered promising candidate materials for biodegradable orthopedic implant applications due to their high mechanical performance and good biocompatibility.However,the presence of a large number of ...Zn-Li alloys are considered promising candidate materials for biodegradable orthopedic implant applications due to their high mechanical performance and good biocompatibility.However,the presence of a large number of second-phase particles in this class of Zn alloys can lead to severe localized degradation due to micro-galvanic corrosion,which is detrimental to the mechanical integrity of the alloys during tissue healing in the human body.In this study we report ultrahigh strength,uniform corrosion,good cytocompatibility,and effective antibacterial ability in Zn-x Li(x=0.3,0.5,0.7;wt%)alloys achieved through supersaturated solid solution treatment(SSST)at 375℃ under ultrahigh pressure of 3 GPa.A high concentration of β-LiZn_(4)phases coexisted with the-Zn matrix in the as-cast Zn-x Li alloys,whereas almost all the Li dissolved into the-Zn matrix of SSST counterparts.The yield strength was 437 MPa for SSST Zn-0.3Li,592 MPa for SSST Zn-0.5 Li and 686 MPa for SSST Zn-0.7Li.The SSST Zn-Li alloys showed uniform degradation with remarkably reduced degradation rates compared to their as-cast counterparts.The 25% concentration extracts of the Zn-x Li alloys demonstrated no cytotoxicity toward MC3T3-E1 cells,and the alloys exhibited effective antibacterial ability agains methicillin-resistant staphylococcus aureus.展开更多
As-received nickel-titanium （NiTi） shape memory alloy with a nominal composition of Ni50.9Ti49.1 （mole fraction,%） was subjected to solution treatment at 1123 K for 2 h and subsequent aging for 2 h at 573 K, 723 K...As-received nickel-titanium （NiTi） shape memory alloy with a nominal composition of Ni50.9Ti49.1 （mole fraction,%） was subjected to solution treatment at 1123 K for 2 h and subsequent aging for 2 h at 573 K, 723 K and 873 K, respectively. The influence of solution treatment and aging on microstructural evolution and mechanical behavior of NiTi alloy was systematically investigated by transmission electron microscopy （TEM）, high resolution transmission electron microscopy （HRTEM）, scanning electron microscopy （SEM） and compression test. Solution treatment contributes to eliminating the Ti2Ni phase in the as-received NiTi sample, in which the TiC phase is unable to be removed. Solution treatment leads to ordered domain of atomic arrangement in NiTi alloy. In all the aged NiTi samples, the Ni4Ti3 precipitates, the R phase and the B2 austenite coexist in the NiTi matrix at room temperature, while the martensitic twins can be observed in the NiTi samples aged at 873 K. In the NiTi samples aged at 573 and 723 K, the fine and dense Ni4Ti3 precipitates distribute uniformly in the NiTi matrix, and thus they are coherent with the B2 matrix. However, in the NiTi sample aged at 873 K, the Ni4Ti3 precipitates exhibit the very inhomogeneous size, and they are coherent, semi-coherent and incoherent with the B2 matrix. In the case of aging at 723 K, the NiTi sample exhibits the maximum yield strength, where the fine and homogeneous Ni4Ti3 precipitates act as the effective obstacles against the dislocation motion, which results in the maximum critical resolved shear stress for dislocation slip.展开更多
Temperature variation and solution treatment of high strength aluminum alloy were investigated with temperature data acquisition system,microstructural observation,mechanical properties test,electrical conductivity me...Temperature variation and solution treatment of high strength aluminum alloy were investigated with temperature data acquisition system,microstructural observation,mechanical properties test,electrical conductivity measurement and differential scanning calorimetry（DSC） analysis.Specimens with two dimensions were employed in the experiment.The results indicate that the specimens with large size undergo low solution temperature and short time,giving rise to the reduction of hardening precipitates.The optimized solution treatments for specimens with dimensions of 25 mm×25 mm×2.5 mm and 70 mm×60 mm×20 mm are（480 ℃,30 min） and（480 ℃,90 min）,respectively.The densities of GP zones and η＇ phases of the small specimen are higher than those of the large specimen,which is consistent with the properties of the alloys.展开更多
The influence of solution treatment on the microstructure and properties of Mg2Si/AZ91D composites fabricated from Mg-SiO2 system via in-situ processing method was investigated.The results show that coarse Chinese scr...The influence of solution treatment on the microstructure and properties of Mg2Si/AZ91D composites fabricated from Mg-SiO2 system via in-situ processing method was investigated.The results show that coarse Chinese script shape Mg2Si phases can be formed by adding SiO2 into AZ91D magnesium alloy with Si content up to 1.5% of the alloy melt.During solution treatment,the morphology and distribution of the coarse Chinese script shape Mg2Si phases are modified.Meanwhile,the β-Mg17Al12 phase is dissolved into the magnesium matrix.With increasing holding time,the coarse Mg2Si phases tend to dissolve,break and spheroidize.After solution treatment at 420 ℃ for 16 h,Mg2Si phases become the finest and relatively well-distributed phase.The tensile strength and elongation are increased by 14.9% and 38.9%,respectively.It is believed that the Mg2Si phases continuously dissolve and break,and finally the spheroidized Mg2Si particles are obtained due to the interface tension of Mg2Si/Mg interface.展开更多
Effects of additions minor contents of 0.03%Sc and 0.12%Zr and solution treatment on microstructure and mechanical properties of Al-9.0Zn-2.8Mg-2.5Cu alloy were studied by metallographic microscopy, differential therm...Effects of additions minor contents of 0.03%Sc and 0.12%Zr and solution treatment on microstructure and mechanical properties of Al-9.0Zn-2.8Mg-2.5Cu alloy were studied by metallographic microscopy, differential thermal analysis （DSC） and transmission electron microscopy （TEM）, in order to obtain high-performance Al alloys. The minor additions of Sc （less than 0.1%） were carried out. The results show that with the additions of 0.03% Sc and 0.12% Zr, the petaloid Al3（Sc,Zr） precipitated phases occur in Al-9.0Zn-2.8Mg-2.5Cu alloy, and Al3（Sc,Zr） particles obviously hinder the recrystallization of Al-9.0Zn-2.8Mg-2.5Cu alloy during homogenizing and extruding processes due to their strong pinning effect on dislocation. Multi-stage solution is better than single solution, for it can avoid recrystallization of Al-9.0Zn-2.8Mg-2.5Cu alloy with the minor contents of Sc （less than 0.1%）. The proper solution treatment is （420 °C, 3 h）＋（465 °C, 2 h） under which Al-9.0Zn-2.8Mg-2.5Cu-0.12Zr-0.03Sc alloy obtains a tensile strength of 777.29 MPa and a elongation of 11.84%.展开更多
In order to achieve good mechanical properties of Al-Cu alloys such as high strength and good toughness,precipitation hardening and artificial aging treatment were applied.As defined by the T6 heat treatment,the stand...In order to achieve good mechanical properties of Al-Cu alloys such as high strength and good toughness,precipitation hardening and artificial aging treatment were applied.As defined by the T6 heat treatment,the standard artificial aging treatment for Al-Cu alloy followed heat treatments of solution treatment at 510-530 ℃ for 2 h,quenching in water at 60 ℃ and then artificial aging at 160-190 ℃ for 2-8 h.The effects of solution treatment and artificial aging on the microstructure and mechanical properties of Al-Cu alloy were studied by optical microscopy（OM）,scanning electron microscopy（SEM）,energy dispersive X-ray spectroscopy（EDS）,transmission electron microscopy（TEM） and tensile test.The results of solution treatment indicate that the mechanical properties of Al-Cu alloy increase and then decrease with the increase of solution temperature.This is because the residual phases dissolve gradually into the matrix,and the fraction of the precipitation and the size of the re-crystallized grain increased.Compared to the solution temperature,the solution holding time has less effect on the microstructure and the mechanical properties of Al-Cu alloy.The artificial aging treatments were conducted at 160-180 ℃ for 2-8 h.The results show that the ultimate tensile strength can be obtained at 180 ℃ for 8 h.Ultimate tensile strength increased with increasing time or temperature.Yield strength was found as the same as the ultimate tensile strength result.展开更多
The effects of single-stage solution treatment(SST),enhanced solution treatment(EST),high-temperature pre-precipitation(HTPP)and multi-stage solution treatment(MST)on the microstructure,mechanical properties and corro...The effects of single-stage solution treatment(SST),enhanced solution treatment(EST),high-temperature pre-precipitation(HTPP)and multi-stage solution treatment(MST)on the microstructure,mechanical properties and corrosion resistance of the as-extruded 7055 aluminium alloy(AA7055)helical profile were investigated using differential scanning calorimetry(DSC),optical microscopy(OM),scanning electron microscopy(SEM),electron back-scattered diffraction(EBSD)and transmission electron microscopy(TEM).It was observed that EST and MST could promote the dissolution of the second-phase particles compared with the traditional SST,and the intergranular phases were distinctly discontinuously distributed after HTPP and MST.There was obvious difference in the main texture type and texture strength for the alloy after different solid solution treatments.HTPP could improve the corrosion resistance of the alloy by regulating the intergranular phases,but the mechanical properties were severely weakened.While the good corrosion resistance of the alloy could be obtained by MST without obvious strength loss.As a result,the MST is an ideal solid solution treatment scheme for AA7055.展开更多
To optimize the solution treatment process of a modified high-pressure die-cast AlSi10MnMg alloy, the influence of the solution treatment on the microstructure, mechanical properties and fracture mechanisms was studie...To optimize the solution treatment process of a modified high-pressure die-cast AlSi10MnMg alloy, the influence of the solution treatment on the microstructure, mechanical properties and fracture mechanisms was studied using OM, SEM, EBSD and tensile test. The experimental results suggest that the solution treatment could be completed in a shorter time at a temperature much lower than the conventional practice. Surface blistering could be avoided and substantial strengthening effect could be achieved in the following aging process. Prolonging solution treatment time and elevating solution temperature would be meaningless or even harmful. The rapid evolution of eutectic silicon during solution treatment, especially at the early stage, affected the way of interaction among α-Al grains during plastic deformation, and changed the ultimate mechanical properties and fracture mode.展开更多
The effect of solution treatment time on the post-formed plasticity and ductile fracture of 7075 aluminum alloy in the hot stamping process was studied.Tensile tests were conducted on the specimens subjected to the ho...The effect of solution treatment time on the post-formed plasticity and ductile fracture of 7075 aluminum alloy in the hot stamping process was studied.Tensile tests were conducted on the specimens subjected to the hot stamping process with different solution treatment time.The digital image correlation(DIC)analysis was used to obtain the strain of the specimen.Based on the experiments and modeling,the Yld2000-3d yield criterion and the DF2014 ductile fracture criterion were calibrated and used to characterize the anisotropy and fracture behavior of the metal,respectively.Furthermore,the microstructure of specimens was studied.The experimental and simulation results indicate that the 7075 aluminum alloy retains distinct anisotropy after the hot stamping process,and there is no obvious effect of extending the solution treatment time on the material anisotropy.However,it is found that a longer solution treatment time can increase the fracture strain of the aluminum alloy during the hot stamping process,which may be related to the decrease of the second-phase particles size.展开更多
The microstructural evolution and kinetic characteristics were studied during solution treatment of AM60B Mg alloy prepared by thixoforming. The results indicate that the microstructural evolution includes two stages...The microstructural evolution and kinetic characteristics were studied during solution treatment of AM60B Mg alloy prepared by thixoforming. The results indicate that the microstructural evolution includes two stages： the first stage involves rapid dissolution of eutectic β （Mg 17 Al 12 ） phase, homogenization and coarsening, and the second stage is regarded as normal grain growth consisting of primary α-Mg particles （primary particles） and secondary α-Mg grains （secondary grains）. In the first stage, the dissolution completes in a quite short time because the fine β phase can quickly dissolve into the small-sized secondary grains. The homogenization of Al element needs relatively long time. Simultaneously, the microstructure morphology and average grain size obviously change. The first stage sustains approximately 1 h when it is solutionized at 395 ℃ Comparatively, the second stage needs very long time and the microstructure evolves quite slowly as a result of low Al content gradient and thus low diffusivity of Al element after the homogenization of the first stage. The growth model of primary particles obeys power function while that of the secondary grains follows the traditional growth equation in the first stage. In the second stage, both of the primary particles and secondary grains behave a same model controlled by diffusion along grain boundaries and through crystal lattice.展开更多
With the aid of scanning electron microscopy （SEM）, energy-dispersive spectroscopy （EDS）, X-ray diffraction （XRD）, differential scanning calorimetry （DSC） analysis and electron backscatter diffraction （EBSD）...With the aid of scanning electron microscopy （SEM）, energy-dispersive spectroscopy （EDS）, X-ray diffraction （XRD）, differential scanning calorimetry （DSC） analysis and electron backscatter diffraction （EBSD）, the microstructure of the alloy in as-extruded state and various solution-treated states was investigated. The results indi- cate that second phase of the as-extruded 7136 aluminum alloy mainly consists of Mg（Zn, Cu, Al）2 and Fe-rich phases. The Mg（Zn, Cu, Al）2 phase directly dissolves into the matrix during solution treatment with various solution temperatures. After solution treated at 475℃ for 1 h, Mg（Zn, Cu, Al）2 phases are dissolved into the matrix, while Fe-rich phases still exist. Fe-rich phases could not dissolve into the matrix by prolonging solution time. The mechanical property test and EBSD observation show that two-stage solution treatment makes no significant improvement in mechanical properties and recrystallization of the alloy. The optimized solution treatment parameter is chosen as 475 ℃/1 h.展开更多
A binary Mg-6Zn biodegradable alloy was solution treated to evaluate the effects of resulting microstructure changes on the alloy＇s degradation rate and mechanisms in-vitro. The treatment was conducted at 350 °C...A binary Mg-6Zn biodegradable alloy was solution treated to evaluate the effects of resulting microstructure changes on the alloy＇s degradation rate and mechanisms in-vitro. The treatment was conducted at 350 °C for 6-48 h. Optical and scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray diffraction were used to analyze the as-cast and treated samples. Immersion and electrochemical tests were performed in simulated body fluid at 37 °C to assess the samples corrosion resistance. To confirm the results of the corrosion tests, p H measurement was carried out. It is found that over 24 h solution treatment dissolves intermetallic phases in matrix and produces an almost single phase microstructure. Decreasing the intermetallic phases results in lower cathode/anode region ratios and lowers corrosion rates. The results of the electrochemical and mass loss tests reveal that extended solution treatment improves the corrosion resistance of the alloy. The results also show that solution at 350 °C for 24 h enhances the corrosion resistance of the as-cast alloy more than 60%. In addition, decreasing intermetallic phases in the microstructure accompanied a lower p H rise reduced corrosion rate. Solution treatment is suggested as a corrosion improving process for the application of Mg-Zn alloys as biodegradable implant materials.展开更多
The effect of Ce/La misch metal addition on the microstructural evolution of as-cast and as-soluted Mg-5.3Zn-0.5Ca（wt.%） alloys was systematically investigated. It was found that Ce/La could effectively refine the a...The effect of Ce/La misch metal addition on the microstructural evolution of as-cast and as-soluted Mg-5.3Zn-0.5Ca（wt.%） alloys was systematically investigated. It was found that Ce/La could effectively refine the as-cast alloy and restrain grain growth during solution treatment, which was derived from the constitutional supercooling during solidification process and the formation of stable intermetallic compounds Ce Mg12 and Mg17La2. Furthermore, Ce/La microalloying and solution treatment resulted in an evolution from the original lamellar Ca2Mg6Zn3/α-Mg to the divorced eutectic structure. The thermal stability of Mg-Zn-Ca alloy could be effectively improved by Ce/La addition, because the low-melting-point binary Mg-Zn phase was transformed to Mg x Zn y-Ca-（Ce/La） phase with higher thermal stability and the amount of Ca2Mg6Zn3/α-Mg eutectic structure was reduced.展开更多
The effect of solution treatment on the microstructure and mechanical properties of a novel 7 A56 aluminum alloy plate was investigated by optical microscopy(OM),scanning electron microscopy(SEM),transmission electron...The effect of solution treatment on the microstructure and mechanical properties of a novel 7 A56 aluminum alloy plate was investigated by optical microscopy(OM),scanning electron microscopy(SEM),transmission electron microscopy(TEM),X-ray diffraction(XRD),differential scanning calorimetry(DSC),conductivity,hardness and tensile tests.The results indicate that the coarse second phases in the hot-rolled plate mainly consist of AlZnMgCu quaternary phase and Al_(7) Cu_(2) Fe phase,and no Al_(2) CuMg phase is found.The amount of the second phases gradually reduces with the increase in temperature(450-480℃)and time(1-8 h)during the solution treatment,and the soluble particles are completely dissolved into the matrix after solution treatment at 470℃for 4 h,while the residual phases are mainly Fe-rich phase along the grain boundaries.The recrystallization fraction of the alloy gradually increases with the degree of solution treatment deepened.When the temperature exceeds480℃,over-burning takes place.The mechanical properties of samples treated at 470℃for various times were tested.After the solution treated at 470℃for 4 h,the quenching conductivity and peak-aged hardness of the alloy are 30.8%IACS and HV 204,respectively.The ultimate tensile strength and yield strength of the samples aged at 120℃for 24 h are 661 and 588 MPa,respectively.展开更多
The transformation and dissolution of Mg（Zn, Cu, Al）2 phase during solution treatment of an Al-Zn-Mg-Cu alloy containing high zinc were investigated by means of optical microscopy （OM）, scanning electron microsco...The transformation and dissolution of Mg（Zn, Cu, Al）2 phase during solution treatment of an Al-Zn-Mg-Cu alloy containing high zinc were investigated by means of optical microscopy （OM）, scanning electron microscopy （SEM）, energy-dispersive X-ray spectrometry （EDX） and X-ray diffraction （XRD）. The results show that solution temperature is the main factor influencing phase dissolution. With solution temperature increasing, the content of residual phases decreases. Phase transformation from Mg（Zn, Cu, Al）2 to S（Al2CuMg） occurs under solution temperature of 450, 460 and 465 ℃. Mg（Zn, Cu, Al）2 phase is directly dissolved into the matrix under solution temperature of 470 and 475 ℃, and no S（Al2CuMg） phase transformed from Mg（Zn, Cu, Al）2 phase is observed. The formation of S（Al2CuMg） phase is mainly controlled by Zn elemental diffusion. The mechanism of transformation and dissolution of second phases was investigated. At low temperature, the dissolution of Zn is faster than that of Mg and Cu, resulting in an appropriate condition to form S（Al2CuMg） phase. At high temperature, the dissolution of main alloying elements has no significant barrier among them to form S（Al2CuMg） phase.展开更多
A new method was exploited using solution treatment and aging process as a pretreatment in preparing semi-solid slurry with fine microstructure before isothermal treatment of wrought aluminum alloy 7A09.Parameters of ...A new method was exploited using solution treatment and aging process as a pretreatment in preparing semi-solid slurry with fine microstructure before isothermal treatment of wrought aluminum alloy 7A09.Parameters of pretreatment were optimized by orthogonal experiment design and proper precursor was prepared.The evolution of microstructure of semi-solid slurry during isothermal treatment was analyzed and the mechanism of microstructure refining was discussed.The result of orthogonal experiment design shows that the optimum parameters are 462 ℃for solution temperature,40min for solution time,132 ℃for aging temperature and 14 h for aging time.Microstructure of isothermal treatment is fine,homogenous,with globular solid grains and a solid fraction between 50%and 70%,which is qualified for later semi-solid forming process.Mechanism of microstructure evolution includes the agglomeration ofα-phase and Ostwald ripening.Precipitations prepared by solution and aging treatment prevent the grains from coarsening and promote the grain ripening to globular shape.展开更多
Effects of solution treatment between 1050 and 1250℃on microstructure and tensile properties of as-cast alloy 625 were investigated.The microstructure and solidification characteristics of the alloy were studied by S...Effects of solution treatment between 1050 and 1250℃on microstructure and tensile properties of as-cast alloy 625 were investigated.The microstructure and solidification characteristics of the alloy were studied by SEM,EDS,EPMA and DTA.The results showed that the solidification sequence of the alloy should be written as L→L+γ→L+γ+MC→L+γ+MC+γ/Laves→γ+MC+γ/Laves.After solution treatment at 1225 and 1250°C,incipient melting of Laves phase was observed.The ultimate tensile strength decreased monotonically with the increase of solution treatment temperature,and the yield strength had no significant variation.The elongation increased slightly at first and then reached a minimum value at 1250°C.The fracture mechanism changed from transgranular mode to intergranular mode after solution at 1250°C for the reason that numerous Laves phases melted at grain boundaries and microcracks nucleated in the molten pool.The suitable solution treatment temperature of this alloy was 1200°C.展开更多
The solution treatment parameters,mechanical properties and corrosion behavior of binary Mg-4Zn alloy were investigated.The results showed that after the solution treatment at 335℃ for 16 h,Mg-4Zn alloy had an ultima...The solution treatment parameters,mechanical properties and corrosion behavior of binary Mg-4Zn alloy were investigated.The results showed that after the solution treatment at 335℃ for 16 h,Mg-4Zn alloy had an ultimate tensile strength of 184.13 MPa and elongation of 9.43%.Furthermore,the corrosion resistance was evaluated by electrochemical measurements and immersion tests in 3.5%NaCl solution.The results revealed that the corrosion current density of the solution treatment Mg alloy was 11.2µA/cm^(−2),it was lower than 15.8µA/cm^(−2) for the as-cast Mg alloy under the same conditions,which was greatly associated with the micro-cathode effect of the second phases.展开更多
基金National Natural Science Foundation of China(Nos.52204400,52204401)Natural Science Foundation of Hebei Province,China(No.E2022203033)。
文摘High-temperature and short-time(HTST)solution heat treatment combined with non-isothermal aging(NIA)was employed to regulate the microstructure and properties of Al−4.5Mg−2.0Zn−0.3Ag alloy.Results indicate that HTST solution heat treatment can not only retain partial deformation dislocations,but inhibit the recrystallization behavior and increase the proportion of low-angle grain boundaries(LAGBs).In the subsequent NIA process,HTST solution heat treatment combined with NIA is instrumental in restraining the degradation of dislocations and promoting precipitation of nano-scale T'-Mg_(32)(Al,Zn,Ag)49 phase,which improves the strength of the alloy greatly.In addition,a higher fraction of LAGBs and the discontinuous distribution of grain boundary precipitates caused by this novel technology meliorate the corrosion resistance of Al−4.5Mg−2.0Zn−0.3Ag alloy.
基金financially supported by Beijing Natural Science Foundation (No.L223001)。
文摘An effort to obtain superior impact properties for Al-7Si-0.35 Mg alloy is presented,where modification with 0.02 wt% Sr and 0.1 wt% La as well as solution treatment was jointly employed.The samples were solution treated at 535℃ for 15 min to 12 h.The microstructure,fracture mechanism,and their correlation with the impact properties of the alloy were studied in detail mainly through optical microscopy(OM),scanning electron microscopy(SEM) and oscillography impact test.The results show that the addition of Sr and La refined the eutectic Si particles significantly from~ 2.05 μm(modified with Sr alone) to~ 0.75 μm in as-cast microstructure,leading to a very homogeneous distribution of spheroidized Si particles in the alloy solution treated at 535℃ for 8 h.The alloy exhibits excellent impact toughness up to 75 J·cm^(-2),which is much higher than the maximum impact toughness of the alloys modified by Sr alone(~ 46 J·cm^(-2)).The major reason for this remarkable increase in the impact property is the dramatic increase in crack initiation energy.The dispersoid-free zones(DFZs)near the eutectic regions mainly consist of the ductile Al-matrix,which exhibits excellent ductility.The ductile Al-matrix of the DFZs hinders the crack propagation,resulting in a significant increase in crack propagation energy.
基金financially supported by Hunan Provincial Natural Science Foundation of China(No.2023JJ40626)the National Natural Science Foundation of China(Nos.11872053 and 51971190)+1 种基金the Post-graduate Scientific Research Innovation Project of Hunan Province(No.CX20210625)the Australian Research Council(ARC)through the Discovery Project(No.DP210101862)。
文摘Zn-Li alloys are considered promising candidate materials for biodegradable orthopedic implant applications due to their high mechanical performance and good biocompatibility.However,the presence of a large number of second-phase particles in this class of Zn alloys can lead to severe localized degradation due to micro-galvanic corrosion,which is detrimental to the mechanical integrity of the alloys during tissue healing in the human body.In this study we report ultrahigh strength,uniform corrosion,good cytocompatibility,and effective antibacterial ability in Zn-x Li(x=0.3,0.5,0.7;wt%)alloys achieved through supersaturated solid solution treatment(SSST)at 375℃ under ultrahigh pressure of 3 GPa.A high concentration of β-LiZn_(4)phases coexisted with the-Zn matrix in the as-cast Zn-x Li alloys,whereas almost all the Li dissolved into the-Zn matrix of SSST counterparts.The yield strength was 437 MPa for SSST Zn-0.3Li,592 MPa for SSST Zn-0.5 Li and 686 MPa for SSST Zn-0.7Li.The SSST Zn-Li alloys showed uniform degradation with remarkably reduced degradation rates compared to their as-cast counterparts.The 25% concentration extracts of the Zn-x Li alloys demonstrated no cytotoxicity toward MC3T3-E1 cells,and the alloys exhibited effective antibacterial ability agains methicillin-resistant staphylococcus aureus.
基金Project (51071056) supported by the National Natural Science Foundation of ChinaProjects (HEUCF121712,HEUCF201317002) supported by the Fundamental Research Funds for the Central Universities of China
文摘As-received nickel-titanium （NiTi） shape memory alloy with a nominal composition of Ni50.9Ti49.1 （mole fraction,%） was subjected to solution treatment at 1123 K for 2 h and subsequent aging for 2 h at 573 K, 723 K and 873 K, respectively. The influence of solution treatment and aging on microstructural evolution and mechanical behavior of NiTi alloy was systematically investigated by transmission electron microscopy （TEM）, high resolution transmission electron microscopy （HRTEM）, scanning electron microscopy （SEM） and compression test. Solution treatment contributes to eliminating the Ti2Ni phase in the as-received NiTi sample, in which the TiC phase is unable to be removed. Solution treatment leads to ordered domain of atomic arrangement in NiTi alloy. In all the aged NiTi samples, the Ni4Ti3 precipitates, the R phase and the B2 austenite coexist in the NiTi matrix at room temperature, while the martensitic twins can be observed in the NiTi samples aged at 873 K. In the NiTi samples aged at 573 and 723 K, the fine and dense Ni4Ti3 precipitates distribute uniformly in the NiTi matrix, and thus they are coherent with the B2 matrix. However, in the NiTi sample aged at 873 K, the Ni4Ti3 precipitates exhibit the very inhomogeneous size, and they are coherent, semi-coherent and incoherent with the B2 matrix. In the case of aging at 723 K, the NiTi sample exhibits the maximum yield strength, where the fine and homogeneous Ni4Ti3 precipitates act as the effective obstacles against the dislocation motion, which results in the maximum critical resolved shear stress for dislocation slip.
基金Project(2010DFB50340) supported by the International Technical Cooperation ProjectProject(50904010) supported by the National Natural Science Foundation of China
文摘Temperature variation and solution treatment of high strength aluminum alloy were investigated with temperature data acquisition system,microstructural observation,mechanical properties test,electrical conductivity measurement and differential scanning calorimetry（DSC） analysis.Specimens with two dimensions were employed in the experiment.The results indicate that the specimens with large size undergo low solution temperature and short time,giving rise to the reduction of hardening precipitates.The optimized solution treatments for specimens with dimensions of 25 mm×25 mm×2.5 mm and 70 mm×60 mm×20 mm are（480 ℃,30 min） and（480 ℃,90 min）,respectively.The densities of GP zones and η＇ phases of the small specimen are higher than those of the large specimen,which is consistent with the properties of the alloys.
基金Project (BG2007030) supported by High-tech Research Program of Jiangsu Province, ChinaProject (07KJA43008) supported by the Natural Science Foundation of Jiangsu Province, ChinaProject (20070299004) supported by the Specialized Research Fund for the Doctoral Program of Higher Education of China
文摘The influence of solution treatment on the microstructure and properties of Mg2Si/AZ91D composites fabricated from Mg-SiO2 system via in-situ processing method was investigated.The results show that coarse Chinese script shape Mg2Si phases can be formed by adding SiO2 into AZ91D magnesium alloy with Si content up to 1.5% of the alloy melt.During solution treatment,the morphology and distribution of the coarse Chinese script shape Mg2Si phases are modified.Meanwhile,the β-Mg17Al12 phase is dissolved into the magnesium matrix.With increasing holding time,the coarse Mg2Si phases tend to dissolve,break and spheroidize.After solution treatment at 420 ℃ for 16 h,Mg2Si phases become the finest and relatively well-distributed phase.The tensile strength and elongation are increased by 14.9% and 38.9%,respectively.It is believed that the Mg2Si phases continuously dissolve and break,and finally the spheroidized Mg2Si particles are obtained due to the interface tension of Mg2Si/Mg interface.
基金Project(51004036)supported by the National Natural Science Foundation of ChinaProject(N120309002)supported by the Fundamental Research Funds for the Central Universities,China
文摘Effects of additions minor contents of 0.03%Sc and 0.12%Zr and solution treatment on microstructure and mechanical properties of Al-9.0Zn-2.8Mg-2.5Cu alloy were studied by metallographic microscopy, differential thermal analysis （DSC） and transmission electron microscopy （TEM）, in order to obtain high-performance Al alloys. The minor additions of Sc （less than 0.1%） were carried out. The results show that with the additions of 0.03% Sc and 0.12% Zr, the petaloid Al3（Sc,Zr） precipitated phases occur in Al-9.0Zn-2.8Mg-2.5Cu alloy, and Al3（Sc,Zr） particles obviously hinder the recrystallization of Al-9.0Zn-2.8Mg-2.5Cu alloy during homogenizing and extruding processes due to their strong pinning effect on dislocation. Multi-stage solution is better than single solution, for it can avoid recrystallization of Al-9.0Zn-2.8Mg-2.5Cu alloy with the minor contents of Sc （less than 0.1%）. The proper solution treatment is （420 °C, 3 h）＋（465 °C, 2 h） under which Al-9.0Zn-2.8Mg-2.5Cu-0.12Zr-0.03Sc alloy obtains a tensile strength of 777.29 MPa and a elongation of 11.84%.
文摘In order to achieve good mechanical properties of Al-Cu alloys such as high strength and good toughness,precipitation hardening and artificial aging treatment were applied.As defined by the T6 heat treatment,the standard artificial aging treatment for Al-Cu alloy followed heat treatments of solution treatment at 510-530 ℃ for 2 h,quenching in water at 60 ℃ and then artificial aging at 160-190 ℃ for 2-8 h.The effects of solution treatment and artificial aging on the microstructure and mechanical properties of Al-Cu alloy were studied by optical microscopy（OM）,scanning electron microscopy（SEM）,energy dispersive X-ray spectroscopy（EDS）,transmission electron microscopy（TEM） and tensile test.The results of solution treatment indicate that the mechanical properties of Al-Cu alloy increase and then decrease with the increase of solution temperature.This is because the residual phases dissolve gradually into the matrix,and the fraction of the precipitation and the size of the re-crystallized grain increased.Compared to the solution temperature,the solution holding time has less effect on the microstructure and the mechanical properties of Al-Cu alloy.The artificial aging treatments were conducted at 160-180 ℃ for 2-8 h.The results show that the ultimate tensile strength can be obtained at 180 ℃ for 8 h.Ultimate tensile strength increased with increasing time or temperature.Yield strength was found as the same as the ultimate tensile strength result.
基金the financial supports from the National Natural Science Foundation of China(No.51975330)Science Fund for Distinguished Young Scholars of Shandong Province,China(No.JQ201810)the Key Research and Development Program of Shandong Province,China(No.2019JZZY010360).
文摘The effects of single-stage solution treatment(SST),enhanced solution treatment(EST),high-temperature pre-precipitation(HTPP)and multi-stage solution treatment(MST)on the microstructure,mechanical properties and corrosion resistance of the as-extruded 7055 aluminium alloy(AA7055)helical profile were investigated using differential scanning calorimetry(DSC),optical microscopy(OM),scanning electron microscopy(SEM),electron back-scattered diffraction(EBSD)and transmission electron microscopy(TEM).It was observed that EST and MST could promote the dissolution of the second-phase particles compared with the traditional SST,and the intergranular phases were distinctly discontinuously distributed after HTPP and MST.There was obvious difference in the main texture type and texture strength for the alloy after different solid solution treatments.HTPP could improve the corrosion resistance of the alloy by regulating the intergranular phases,but the mechanical properties were severely weakened.While the good corrosion resistance of the alloy could be obtained by MST without obvious strength loss.As a result,the MST is an ideal solid solution treatment scheme for AA7055.
基金Project(U1537202) supported by the National Natural Science Foundation of ChinaProject(BA2015041) supported by the Special Funding Program on Transformation of Scientific and Technological Achievements in Jiangsu Province,China
文摘To optimize the solution treatment process of a modified high-pressure die-cast AlSi10MnMg alloy, the influence of the solution treatment on the microstructure, mechanical properties and fracture mechanisms was studied using OM, SEM, EBSD and tensile test. The experimental results suggest that the solution treatment could be completed in a shorter time at a temperature much lower than the conventional practice. Surface blistering could be avoided and substantial strengthening effect could be achieved in the following aging process. Prolonging solution treatment time and elevating solution temperature would be meaningless or even harmful. The rapid evolution of eutectic silicon during solution treatment, especially at the early stage, affected the way of interaction among α-Al grains during plastic deformation, and changed the ultimate mechanical properties and fracture mode.
基金the National Natural Science Foundation of China(No.U1760205).
文摘The effect of solution treatment time on the post-formed plasticity and ductile fracture of 7075 aluminum alloy in the hot stamping process was studied.Tensile tests were conducted on the specimens subjected to the hot stamping process with different solution treatment time.The digital image correlation(DIC)analysis was used to obtain the strain of the specimen.Based on the experiments and modeling,the Yld2000-3d yield criterion and the DF2014 ductile fracture criterion were calibrated and used to characterize the anisotropy and fracture behavior of the metal,respectively.Furthermore,the microstructure of specimens was studied.The experimental and simulation results indicate that the 7075 aluminum alloy retains distinct anisotropy after the hot stamping process,and there is no obvious effect of extending the solution treatment time on the material anisotropy.However,it is found that a longer solution treatment time can increase the fracture strain of the aluminum alloy during the hot stamping process,which may be related to the decrease of the second-phase particles size.
基金Project(G2007CB613706)supported by the National Basic Research Program of ChinaProject supported by the Development Program for Outstanding Young Teachers in Lanzhou University of Technology, ChinaProject(SKL03004)supported by the Opening Foundation of State Key Laboratory of Advanced Nonferrous Materials, China
文摘The microstructural evolution and kinetic characteristics were studied during solution treatment of AM60B Mg alloy prepared by thixoforming. The results indicate that the microstructural evolution includes two stages： the first stage involves rapid dissolution of eutectic β （Mg 17 Al 12 ） phase, homogenization and coarsening, and the second stage is regarded as normal grain growth consisting of primary α-Mg particles （primary particles） and secondary α-Mg grains （secondary grains）. In the first stage, the dissolution completes in a quite short time because the fine β phase can quickly dissolve into the small-sized secondary grains. The homogenization of Al element needs relatively long time. Simultaneously, the microstructure morphology and average grain size obviously change. The first stage sustains approximately 1 h when it is solutionized at 395 ℃ Comparatively, the second stage needs very long time and the microstructure evolves quite slowly as a result of low Al content gradient and thus low diffusivity of Al element after the homogenization of the first stage. The growth model of primary particles obeys power function while that of the secondary grains follows the traditional growth equation in the first stage. In the second stage, both of the primary particles and secondary grains behave a same model controlled by diffusion along grain boundaries and through crystal lattice.
基金supported by the National Key Research and Development Program of China (No. 2016YFB0300903)the National Program on Key Basic Research Project of China (No. 2012CB619504)the National Natural Science Foundation of China (No. 51274046)
文摘With the aid of scanning electron microscopy （SEM）, energy-dispersive spectroscopy （EDS）, X-ray diffraction （XRD）, differential scanning calorimetry （DSC） analysis and electron backscatter diffraction （EBSD）, the microstructure of the alloy in as-extruded state and various solution-treated states was investigated. The results indi- cate that second phase of the as-extruded 7136 aluminum alloy mainly consists of Mg（Zn, Cu, Al）2 and Fe-rich phases. The Mg（Zn, Cu, Al）2 phase directly dissolves into the matrix during solution treatment with various solution temperatures. After solution treated at 475℃ for 1 h, Mg（Zn, Cu, Al）2 phases are dissolved into the matrix, while Fe-rich phases still exist. Fe-rich phases could not dissolve into the matrix by prolonging solution time. The mechanical property test and EBSD observation show that two-stage solution treatment makes no significant improvement in mechanical properties and recrystallization of the alloy. The optimized solution treatment parameter is chosen as 475 ℃/1 h.
基金the Ministry of Higher Education of Malaysia for the financial support (Vote No. Q.J130000.2524.04H18)Faculty of Mechanical Engineering of Universiti Teknologi Malaysia (UTM) for providing research facilities
文摘A binary Mg-6Zn biodegradable alloy was solution treated to evaluate the effects of resulting microstructure changes on the alloy＇s degradation rate and mechanisms in-vitro. The treatment was conducted at 350 °C for 6-48 h. Optical and scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray diffraction were used to analyze the as-cast and treated samples. Immersion and electrochemical tests were performed in simulated body fluid at 37 °C to assess the samples corrosion resistance. To confirm the results of the corrosion tests, p H measurement was carried out. It is found that over 24 h solution treatment dissolves intermetallic phases in matrix and produces an almost single phase microstructure. Decreasing the intermetallic phases results in lower cathode/anode region ratios and lowers corrosion rates. The results of the electrochemical and mass loss tests reveal that extended solution treatment improves the corrosion resistance of the alloy. The results also show that solution at 350 °C for 24 h enhances the corrosion resistance of the as-cast alloy more than 60%. In addition, decreasing intermetallic phases in the microstructure accompanied a lower p H rise reduced corrosion rate. Solution treatment is suggested as a corrosion improving process for the application of Mg-Zn alloys as biodegradable implant materials.
基金supported by the National Natural Science Foundation of China(51401200)Natural Science Foundation of Jilin Province(20140520099JH)+4 种基金National Science & Technology Pillar Program(2012BAE01B04)Chinese Academy of Sciences of Western Action Plan Project(KZCX2-XB3-06)the National Natural Science Foundation of China Major Project(91122030)National High Technology Research and Development Program of China(2011AA03A407)National Natural Science Foundation for Creative Research Group(20921002)
文摘The effect of Ce/La misch metal addition on the microstructural evolution of as-cast and as-soluted Mg-5.3Zn-0.5Ca（wt.%） alloys was systematically investigated. It was found that Ce/La could effectively refine the as-cast alloy and restrain grain growth during solution treatment, which was derived from the constitutional supercooling during solidification process and the formation of stable intermetallic compounds Ce Mg12 and Mg17La2. Furthermore, Ce/La microalloying and solution treatment resulted in an evolution from the original lamellar Ca2Mg6Zn3/α-Mg to the divorced eutectic structure. The thermal stability of Mg-Zn-Ca alloy could be effectively improved by Ce/La addition, because the low-melting-point binary Mg-Zn phase was transformed to Mg x Zn y-Ca-（Ce/La） phase with higher thermal stability and the amount of Ca2Mg6Zn3/α-Mg eutectic structure was reduced.
基金financially supported by the National Key Research and Development Program of China(No.2016YFB0300803)the National Natural Science Foundation of China(No.51274046)the National Key Basic Research Program(No.2012CB619504)。
文摘The effect of solution treatment on the microstructure and mechanical properties of a novel 7 A56 aluminum alloy plate was investigated by optical microscopy(OM),scanning electron microscopy(SEM),transmission electron microscopy(TEM),X-ray diffraction(XRD),differential scanning calorimetry(DSC),conductivity,hardness and tensile tests.The results indicate that the coarse second phases in the hot-rolled plate mainly consist of AlZnMgCu quaternary phase and Al_(7) Cu_(2) Fe phase,and no Al_(2) CuMg phase is found.The amount of the second phases gradually reduces with the increase in temperature(450-480℃)and time(1-8 h)during the solution treatment,and the soluble particles are completely dissolved into the matrix after solution treatment at 470℃for 4 h,while the residual phases are mainly Fe-rich phase along the grain boundaries.The recrystallization fraction of the alloy gradually increases with the degree of solution treatment deepened.When the temperature exceeds480℃,over-burning takes place.The mechanical properties of samples treated at 470℃for various times were tested.After the solution treated at 470℃for 4 h,the quenching conductivity and peak-aged hardness of the alloy are 30.8%IACS and HV 204,respectively.The ultimate tensile strength and yield strength of the samples aged at 120℃for 24 h are 661 and 588 MPa,respectively.
基金financially supported by the National Program on Key Basic Research Project of China (No. 2012CB619504)National Natural Science Foundation of China (No. 51274046)
文摘The transformation and dissolution of Mg（Zn, Cu, Al）2 phase during solution treatment of an Al-Zn-Mg-Cu alloy containing high zinc were investigated by means of optical microscopy （OM）, scanning electron microscopy （SEM）, energy-dispersive X-ray spectrometry （EDX） and X-ray diffraction （XRD）. The results show that solution temperature is the main factor influencing phase dissolution. With solution temperature increasing, the content of residual phases decreases. Phase transformation from Mg（Zn, Cu, Al）2 to S（Al2CuMg） occurs under solution temperature of 450, 460 and 465 ℃. Mg（Zn, Cu, Al）2 phase is directly dissolved into the matrix under solution temperature of 470 and 475 ℃, and no S（Al2CuMg） phase transformed from Mg（Zn, Cu, Al）2 phase is observed. The formation of S（Al2CuMg） phase is mainly controlled by Zn elemental diffusion. The mechanism of transformation and dissolution of second phases was investigated. At low temperature, the dissolution of Zn is faster than that of Mg and Cu, resulting in an appropriate condition to form S（Al2CuMg） phase. At high temperature, the dissolution of main alloying elements has no significant barrier among them to form S（Al2CuMg） phase.
基金Project(2007-83)supported by Science and Technology Development Projects of Weihai,Shandong Province。
文摘A new method was exploited using solution treatment and aging process as a pretreatment in preparing semi-solid slurry with fine microstructure before isothermal treatment of wrought aluminum alloy 7A09.Parameters of pretreatment were optimized by orthogonal experiment design and proper precursor was prepared.The evolution of microstructure of semi-solid slurry during isothermal treatment was analyzed and the mechanism of microstructure refining was discussed.The result of orthogonal experiment design shows that the optimum parameters are 462 ℃for solution temperature,40min for solution time,132 ℃for aging temperature and 14 h for aging time.Microstructure of isothermal treatment is fine,homogenous,with globular solid grains and a solid fraction between 50%and 70%,which is qualified for later semi-solid forming process.Mechanism of microstructure evolution includes the agglomeration ofα-phase and Ostwald ripening.Precipitations prepared by solution and aging treatment prevent the grains from coarsening and promote the grain ripening to globular shape.
基金the financial support from the National Natural Science Foundation of China (51571191)
文摘Effects of solution treatment between 1050 and 1250℃on microstructure and tensile properties of as-cast alloy 625 were investigated.The microstructure and solidification characteristics of the alloy were studied by SEM,EDS,EPMA and DTA.The results showed that the solidification sequence of the alloy should be written as L→L+γ→L+γ+MC→L+γ+MC+γ/Laves→γ+MC+γ/Laves.After solution treatment at 1225 and 1250°C,incipient melting of Laves phase was observed.The ultimate tensile strength decreased monotonically with the increase of solution treatment temperature,and the yield strength had no significant variation.The elongation increased slightly at first and then reached a minimum value at 1250°C.The fracture mechanism changed from transgranular mode to intergranular mode after solution at 1250°C for the reason that numerous Laves phases melted at grain boundaries and microcracks nucleated in the molten pool.The suitable solution treatment temperature of this alloy was 1200°C.
文摘The solution treatment parameters,mechanical properties and corrosion behavior of binary Mg-4Zn alloy were investigated.The results showed that after the solution treatment at 335℃ for 16 h,Mg-4Zn alloy had an ultimate tensile strength of 184.13 MPa and elongation of 9.43%.Furthermore,the corrosion resistance was evaluated by electrochemical measurements and immersion tests in 3.5%NaCl solution.The results revealed that the corrosion current density of the solution treatment Mg alloy was 11.2µA/cm^(−2),it was lower than 15.8µA/cm^(−2) for the as-cast Mg alloy under the same conditions,which was greatly associated with the micro-cathode effect of the second phases.
