In this paper the design and implementation of sixth-order lowpass elliptic switched-capacitor filter( SCF) for interface circuit of Micro-Electro-Mechanical System( MEMS) sensor are presented. This work aims to lower...In this paper the design and implementation of sixth-order lowpass elliptic switched-capacitor filter( SCF) for interface circuit of Micro-Electro-Mechanical System( MEMS) sensor are presented. This work aims to lower total harmonic distortion( THD) without deteriorating other performances. After system design in Simulink,the filter is realized in transistor level and finally fabricated in Central Semiconductor Manufacturing Corporation( CSMC) 0.5 μm metal-oxide-semiconductor( CMOS) technology. Typical measured results are: it operates with 25: 1 clock-to-corner frequency ratio and a 10 k Hz maximum corner frequency. The maximum passband ripple is about 0.49 d B and the minimum stopband rejection is 40 d B for the temperature from-20 ℃to 80 ℃. For the 250 k Hz clock frequency setting,given the 1 k Hz,- 8 d BVrms input signal,the measured worst case THD is-64 d B. The active area of the chip is 2.8 mm2 with 8 pads. The analog power dissipation is10 m W from a 5 V power supply.展开更多
In this study,a fifth-degree cubature particle filter(5CPF)is proposed to address the limited estimation accuracy in traditional particle filter algorithms for bearings-only tracking(BOT).This algorithm calculates the...In this study,a fifth-degree cubature particle filter(5CPF)is proposed to address the limited estimation accuracy in traditional particle filter algorithms for bearings-only tracking(BOT).This algorithm calculates the recommended density function by introducing a fifth-degree cubature Kalman filter algorithm to guide particle sampling,which effectively alleviates the problem of particle degradation and significantly improves the estimation accuracy of the filter.However,the 5CPF algorithm exhibits high computational complexity,particularly in scenarios with a large number of particles.Therefore,we propose the extended Kalman filter(EKF)-5CPF algorithm,which employs an EKF to replace the time update step for each particle in the 5CPF.This enhances the algorithm’s real-time capability while maintaining the high precision advantage of the 5CPF algorithm.In addition,we construct bearing-only dual-station and single-motion station target tracking systems,and the filtering performances of 5CPF and EKF-5CPF algorithms under different conditions are analyzed.The results show that both the 5CPF algorithm and EKF-5CPF have strong robustness and can adapt to different noise environments.Furthermore,both algorithms significantly outperform traditional nonlinear filtering algorithms in terms of convergence speed,tracking accuracy,and overall stability.展开更多
In this paper,we construct the rogue wave solutions of the sixth-order nonlinear Schrodinger equation on a background of Jacobian elliptic functions dn and cn by means of the nonlinearization of a spectral problem and...In this paper,we construct the rogue wave solutions of the sixth-order nonlinear Schrodinger equation on a background of Jacobian elliptic functions dn and cn by means of the nonlinearization of a spectral problem and Darboux transformation approach.The solutions we find present the dynamic phenomena of higher-order nonlinear wave equations.展开更多
In this paper,we develop a new sixth-order WENO scheme by adopting a convex combina-tion of a sixth-order global reconstruction and four low-order local reconstructions.Unlike the classical WENO schemes,the associated...In this paper,we develop a new sixth-order WENO scheme by adopting a convex combina-tion of a sixth-order global reconstruction and four low-order local reconstructions.Unlike the classical WENO schemes,the associated linear weights of the new scheme can be any positive numbers with the only requirement that their sum equals one.Further,a very simple smoothness indicator for the global stencil is proposed.The new scheme can achieve sixth-order accuracy in smooth regions.Numerical tests in some one-and two-dimensional bench-mark problems show that the new scheme has a little bit higher resolution compared with the recently developed sixth-order WENO-Z6 scheme,and it is more efficient than the classical fifth-order WENO-JS5 scheme and the recently developed sixth-order WENO6-S scheme.展开更多
We consider the singularly perturbed sixth-order Boussinesq-type equation, which describes the bidirectional propagation of small amplitude and long capillary gravity waves on the surface of shallow water for bond num...We consider the singularly perturbed sixth-order Boussinesq-type equation, which describes the bidirectional propagation of small amplitude and long capillary gravity waves on the surface of shallow water for bond number (surface tension parameter) less than but very close to 1/3. The sufficient conditions of blow-up of solution to the Cauchy problem for this equation are given.展开更多
By using Richardson extrapolation and fourth-order compact finite difference scheme on different scale grids, a sixth-order solution is computed on the coarse grid. Other three techniques are applied to obtain a sixth...By using Richardson extrapolation and fourth-order compact finite difference scheme on different scale grids, a sixth-order solution is computed on the coarse grid. Other three techniques are applied to obtain a sixth-order solution on the fine grid, and thus give out three kinds of Richardson extrapolation-based sixth order compact computation methods. By carefully analyzing the truncation errors respectively on 2D Poisson equation, we compare the accuracy of these three sixth order methods theoretically. Numerical results for two test problems are discussed.展开更多
In this paper,an advanced satellite navigation filter design,referred to as the Variational Bayesian Maximum Correntropy Extended Kalman Filter(VBMCEKF),is introduced to enhance robustness and adaptability in scenario...In this paper,an advanced satellite navigation filter design,referred to as the Variational Bayesian Maximum Correntropy Extended Kalman Filter(VBMCEKF),is introduced to enhance robustness and adaptability in scenarios with non-Gaussian noise and heavy-tailed outliers.The proposed design modifies the extended Kalman filter(EKF)for the global navigation satellite system(GNSS),integrating the maximum correntropy criterion(MCC)and the variational Bayesian(VB)method.This adaptive algorithm effectively reduces non-line-of-sight(NLOS)reception contamination and improves estimation accuracy,particularly in time-varying GNSS measurements.Experimental results show that the proposed method significantly outperforms conventional approaches in estimation accuracy under heavy-tailed outliers and non-Gaussian noise.By combining MCC with VB approximation for real-time noise covariance estimation using fixed-point iteration,the VBMCEKF achieves superior filtering performance in challenging GNSS conditions.The method’s adaptability and precision make it ideal for improving satellite navigation performance in stochastic environments.展开更多
The integration of surface filtration and catalytic decomposition functions in catalytic bags enables the synergistic removal of multiple pollutants(such as dust,nitrogen oxide,acid gases,and dioxins)in a single react...The integration of surface filtration and catalytic decomposition functions in catalytic bags enables the synergistic removal of multiple pollutants(such as dust,nitrogen oxide,acid gases,and dioxins)in a single reactor,thus effectively reducing the cost and operational difficulties associated with flue gas treatment.In this study,Mn-Ce-Sm-Sn(MCSS)catalysts were prepared and loaded onto hightemperature resistant polyimide(P84)filter through ultrasonic impregnation to create composite catalytic filter.The results demonstrate that the NO conversion rates of the composite catalytic filter consistently achieve above 95%within the temperature range of 160-260℃,with a chlorobenzene T_(90)value of 230℃.The ultrasonic impregnation method effectively loaded the catalyst onto the filter,ensuring high dispersion both on the surface and inside the filter.This increased exposure of catalyst active sites enhances the catalytic activity of the composite catalytic filter.Additionally,increasing the catalyst loading leads to a gradual decrease in permeability,an increase in pressure drops and the long residence time of the flue gas,thereby improving catalytic activity.Compared to ordinary impregnation methods,ultrasonic impregnation improves the bonding strength between the catalyst and filter,as well as the permeability of the composite catalytic filter under the same loading conditions.Overall,this study presents a novel approach to prepare composite catalytic filter for the simultaneous removal of NO and chlorobenzene at low temperatures.展开更多
A medical image encryption is proposed based on the Fisher-Yates scrambling,filter diffusion and S-box substitution.First,chaotic sequence associated with the plaintext is generated by logistic-sine-cosine system,whic...A medical image encryption is proposed based on the Fisher-Yates scrambling,filter diffusion and S-box substitution.First,chaotic sequence associated with the plaintext is generated by logistic-sine-cosine system,which is used for the scrambling,substitution and diffusion processes.The three-dimensional Fisher-Yates scrambling,S-box substitution and diffusion are employed for the first round of encryption.The chaotic sequence is adopted for secondary encryption to scramble the ciphertext obtained in the first round.Then,three-dimensional filter is applied to diffusion for further useful information hiding.The key to the algorithm is generated by the combination of hash value of plaintext image and the input parameters.It improves resisting ability of plaintext attacks.The security analysis shows that the algorithm is effective and efficient.It can resist common attacks.In addition,the good diffusion effect shows that the scheme can solve the differential attacks encountered in the transmission of medical images and has positive implications for future research.展开更多
Brackish water(BW)irrigation may cause soil quality deterioration and thereby a decrease in crop yields.Here we examined the impacts of applying gasification filter cake(GFC),intercropping with Portulaca oleracea(PO),...Brackish water(BW)irrigation may cause soil quality deterioration and thereby a decrease in crop yields.Here we examined the impacts of applying gasification filter cake(GFC),intercropping with Portulaca oleracea(PO),and their combination on soil quality,nutrient uptake by plants and tomato yields under BW irrigation.The treatments evaluated included(i)freshwater irrigation(Control),(ii)BW irrigation,(iii)GFC application under BW irrigation(BW+GFC),(iv)intercropping with PO under BW irrigation(BW+PO),and(v)the combined application of GFC and PO under BW irrigation(BW+PO+GFC).Overall,the use of BW for irrigation resulted in a decline in both soil quality(assessed by a soil quality index(SQI)integrating a wide range of key soil properties including salinity,nutrient availability and microbial activities)and crop yields.Nevertheless,when subjected to BW irrigation,the application of GFC successfully prevented soil salinity.Additionally,the intercropping of PO decreased the soil sodium adsorption ratio and improved the absorption of nutrients by plants.As a result,the BW+GFC+PO treatment generally showed higher tomato yield as compared to other BW-related treatments(i.e.BW,BW+GFC and BW+PO).Compared to BW,the BW+GFC+PO treatment had an average increase of 24.7% in the total fruit yield of four Cropping Seasons.Furthermore,the BW+GFC+PO treatment consistently exhibited the highest fruit quality index(FQI).Taken together,the combined application of GFC and PO is effective in promoting soil quality and crop yields under BW irrigation.展开更多
Fault detection in industrial robot drive systems is a critical aspect of ensuring operational reliability and efficiency.To address the challenge of balancing accuracy and robustness in existing fault detection metho...Fault detection in industrial robot drive systems is a critical aspect of ensuring operational reliability and efficiency.To address the challenge of balancing accuracy and robustness in existing fault detection methods,this paper proposes an enhanced fault detection method based on the unscented Kalman filter(UKF).A comprehensive mathematical model of the brushless DC motor drive system is developed to provide a theoretical foundation for the design of subsequent fault detection methods.The conventional UKF estimation process is detailed,and its limitations in balancing estimation accuracy and robustness are addressed by introducing a dynamic,time-varying boundary layer.To further enhance detection performance,the method incorporates residual analysis using improved z-score and signal-tonoise ratio(SNR)metrics.Numerical simulations under both fault-free and faulty conditions demonstrate that the proposed approach achieves lower root mean square error(RMSE)in fault-free scenarios and provides reliable fault detection.These results highlight the potential of the proposed method to enhance the reliability and robustness of fault detection in industrial robot drive systems.展开更多
The output feedback active disturbance rejection control of a valve-controlled cylinder electro-hydraulic servo system is investigated in this paper.First,a comprehensive nonlinear mathematical model that encompasses ...The output feedback active disturbance rejection control of a valve-controlled cylinder electro-hydraulic servo system is investigated in this paper.First,a comprehensive nonlinear mathematical model that encompasses both matched and mismatched disturbances is formulated.Due to the fact that only position information can be measured,a linear Extended State Observer(ESO)is introduced to estimate unknown states and matched disturbances,while a dedicated disturbance observer is constructed to estimate mismatched disturbances.Different from the traditional observer results,the design of the disturbance observer used in this study is carried out under the constraint of output feedback.Furthermore,an output feedback nonlinear controller is proposed leveraging the aforementioned observers to achieve accurate trajectory tracking.To mitigate the inherent differential explosion problem of the traditional backstepping framework,a finite-time stable command filter is incorporated.Simultaneously,considering transient filtering errors,a set of error compensation signals are designed to counter their negative impact effectively.Theoretical analysis affirms that the proposed control strategy ensures the boundedness of all signals within the closed-loop system.Additionally,under the specific condition of only time-invariant disturbances in the system,the conclusion of asymptotic stability is established.Finally,the algorithm’s efficacy is validated through comparative experiments.展开更多
Terrain Aided Navigation(TAN)technology has become increasingly important due to its effectiveness in environments where Global Positioning System(GPS)is unavailable.In recent years,TAN systems have been extensively r...Terrain Aided Navigation(TAN)technology has become increasingly important due to its effectiveness in environments where Global Positioning System(GPS)is unavailable.In recent years,TAN systems have been extensively researched for both aerial and underwater navigation applications.However,many TAN systems that rely on recursive Unmanned Aerial Vehicle(UAV)position estimation methods,such as Extended Kalman Filters(EKF),often face challenges with divergence and instability,particularly in highly non-linear systems.To address these issues,this paper proposes and investigates a hybrid two-stage TAN positioning system for UAVs that utilizes Particle Filter.To enhance the system’s robustness against uncertainties caused by noise and to estimate additional system states,a Fuzzy Particle Filter(FPF)is employed in the first stage.This approach introduces a novel terrain composite feature that enables a fuzzy expert system to analyze terrain non-linearities and dynamically adjust the number of particles in real-time.This design allows the UAV to be efficiently localized in GPS-denied environments while also reducing the computational complexity of the particle filter in real-time applications.In the second stage,an Error State Kalman Filter(ESKF)is implemented to estimate the UAV’s altitude.The ESKF is chosen over the conventional EKF method because it is more suitable for non-linear systems.Simulation results demonstrate that the proposed fuzzy-based terrain composite method achieves high positional accuracy while reducing computational time and memory usage.展开更多
In this paper, the problem of cubature Kalman fusion filtering(CKFF) is addressed for multi-sensor systems under amplify-and-forward(AaF) relays. For the purpose of facilitating data transmission, AaF relays are utili...In this paper, the problem of cubature Kalman fusion filtering(CKFF) is addressed for multi-sensor systems under amplify-and-forward(AaF) relays. For the purpose of facilitating data transmission, AaF relays are utilized to regulate signal communication between sensors and filters. Here, the randomly varying channel parameters are represented by a set of stochastic variables whose occurring probabilities are permitted to exhibit bounded uncertainty. Employing the spherical-radial cubature principle, a local filter under AaF relays is initially constructed. This construction ensures and minimizes an upper bound of the filtering error covariance by designing an appropriate filter gain. Subsequently, the local filters are fused through the application of the covariance intersection fusion rule. Furthermore, the uniform boundedness of the filtering error covariance's upper bound is investigated through establishing certain sufficient conditions. The effectiveness of the proposed CKFF scheme is ultimately validated via a simulation experiment concentrating on a three-phase induction machine.展开更多
A novel substrate integrated microstrip to ultra-thin cavity filter transition operating in the W-band is proposed in this letter.The structure is a new method of connecting microstrip circuits and waveguide filters,a...A novel substrate integrated microstrip to ultra-thin cavity filter transition operating in the W-band is proposed in this letter.The structure is a new method of connecting microstrip circuits and waveguide filters,and this new structure enables a planar integrated transition from microstrip lines to ultra-thin cavity filters,thereby reducing the size of the transition structure and achieving miniaturization.The structure includes a conventional tapered microstrip transition structure,which guides the electromagnetic field from the microstrip line to the reduced-height dielectric-filled waveguide,and an air-filled matching cavity which is placed between the dielectric-filled waveguide and the ultra-thin cavity filter.The heights of the microstrip line,the dielectric-filled waveguide and the ultra-thin cavity filter are the same,enabling seamless integration within a planar radio-frequency(RF)circuit.To facilitate testing,mature finline transition structures are integrated at both ends of the microstrip line during fabrications.The simulation results of the fabricated microstrip to ultra-thin cavity filter transition with the finline transition structure,with a passband of 91.5-96.5 GHz,has an insertion loss of less than 1.9 dB and a return loss lower than-20 dB.And the whole structure has also been measured which achieves an insertion loss less than 2.6 dB and a return loss lower than-15 dB within the filter's passband,including the additional insertion loss introduced by the finline transitions.Finally,a W-band compact up-conversion module is designed,and the test results show that after using the proposed structure,the module achieves 95 dBc suppression of the 84 GHz local oscillator.It is also demonstrated that the structure proposed in this letter achieves miniaturization of the system integration without compromising the filter performance.展开更多
Filter capacitors play an important role in altern-ating current(AC)-line filtering for stabilizing voltage,sup-pressing harmonics,and improving power quality.However,traditional aluminum electrolytic capacitors(AECs)...Filter capacitors play an important role in altern-ating current(AC)-line filtering for stabilizing voltage,sup-pressing harmonics,and improving power quality.However,traditional aluminum electrolytic capacitors(AECs)suffer from a large size,short lifespan,low power density,and poor reliability,which limits their use.In contrast,ultrafast supercapacitors(SCs)are ideal for replacing commercial AECs because of their extremely high power densities,fast charging and discharging,and excellent high-frequency re-sponse.We review the design principles and key parameters for ultrafast supercapacitors and summarize research pro-gress in recent years from the aspects of electrode materials,electrolytes,and device configurations.The preparation,structures,and frequency response performance of electrode materials mainly consisting of carbon materials such as graphene and carbon nanotubes,conductive polymers,and transition metal compounds,are focused on.Finally,future research directions for ultrafast SCs are suggested.展开更多
Dear Editor,This letter presents an improved repetitive controller(IRC) that uses a complex-coefficient filter to enhance the tracking performance of a system for periodic signals. Compared with the low-pass filter us...Dear Editor,This letter presents an improved repetitive controller(IRC) that uses a complex-coefficient filter to enhance the tracking performance of a system for periodic signals. Compared with the low-pass filter used in the conventional repetitive controller(CRC), the complex-coefficient filter causes less change in the phase and amplitude of a signal at the frequencies of the periodic signal, especially at the fundamental frequency, when the two filters have the same cutofffrequency.展开更多
The visual noise of each light intensity area is different when the image is drawn by Monte Carlo method.However,the existing denoising algorithms have limited denoising performance under complex lighting conditions a...The visual noise of each light intensity area is different when the image is drawn by Monte Carlo method.However,the existing denoising algorithms have limited denoising performance under complex lighting conditions and are easy to lose detailed information.So we propose a rendered image denoising method with filtering guided by lighting information.First,we design an image segmentation algorithm based on lighting information to segment the image into different illumination areas.Then,we establish the parameter prediction model guided by lighting information for filtering(PGLF)to predict the filtering parameters of different illumination areas.For different illumination areas,we use these filtering parameters to construct area filters,and the filters are guided by the lighting information to perform sub-area filtering.Finally,the filtering results are fused with auxiliary features to output denoised images for improving the overall denoising effect of the image.Under the physically based rendering tool(PBRT)scene and Tungsten dataset,the experimental results show that compared with other guided filtering denoising methods,our method improves the peak signal-to-noise ratio(PSNR)metrics by 4.2164 dB on average and the structural similarity index(SSIM)metrics by 7.8%on average.This shows that our method can better reduce the noise in complex lighting scenesand improvethe imagequality.展开更多
High-selectivity common-mode(CM)and differential-mode(DM)reflectionless balanced bandpass filters(BBPFs)are proposed in this article.By loading absorption networks at single/both ends of the basic ring resonator,input...High-selectivity common-mode(CM)and differential-mode(DM)reflectionless balanced bandpass filters(BBPFs)are proposed in this article.By loading absorption networks at single/both ends of the basic ring resonator,input-/two-port wideband CM and DM reflectionless performance,wideband filtering performance and all-stop CM suppression are obtained.The absorption network composed of K-sections of coupled-lines(CLs)terminated with grounded resistors can not only extend the filtering performance to high order,but also realize wideband absorption of CM noise and out-of-band DM signals.Absorptive stubs are loaded at ports to increase the design flexibility and enhance the absorption.As for the input-reflectionless type,multiple independently controlled transmission zeros(TZs)are obtained by the TZ control network to improves the selectivity and out-of-band rejection.A set of 2 GHz micro-strip BBPFs are designed and measured,which shows simultaneous CM and DM absorption performance.展开更多
The surge of large-scale models in recent years has led to breakthroughs in numerous fields,but it has also introduced higher computational costs and more complex network architectures.These increasingly large and int...The surge of large-scale models in recent years has led to breakthroughs in numerous fields,but it has also introduced higher computational costs and more complex network architectures.These increasingly large and intricate networks pose challenges for deployment and execution while also exacerbating the issue of network over-parameterization.To address this issue,various network compression techniques have been developed,such as network pruning.A typical pruning algorithm follows a three-step pipeline involving training,pruning,and retraining.Existing methods often directly set the pruned filters to zero during retraining,significantly reducing the parameter space.However,this direct pruning strategy frequently results in irreversible information loss.In the early stages of training,a network still contains much uncertainty,and evaluating filter importance may not be sufficiently rigorous.To manage the pruning process effectively,this paper proposes a flexible neural network pruning algorithm based on the logistic growth differential equation,considering the characteristics of network training.Unlike other pruning algorithms that directly reduce filter weights,this algorithm introduces a three-stage adaptive weight decay strategy inspired by the logistic growth differential equation.It employs a gentle decay rate in the initial training stage,a rapid decay rate during the intermediate stage,and a slower decay rate in the network convergence stage.Additionally,the decay rate is adjusted adaptively based on the filter weights at each stage.By controlling the adaptive decay rate at each stage,the pruning of neural network filters can be effectively managed.In experiments conducted on the CIFAR-10 and ILSVRC-2012 datasets,the pruning of neural networks significantly reduces the floating-point operations while maintaining the same pruning rate.Specifically,when implementing a 30%pruning rate on the ResNet-110 network,the pruned neural network not only decreases floating-point operations by 40.8%but also enhances the classification accuracy by 0.49%compared to the original network.展开更多
基金Sponsored by the Fundamental Research Funds for the Central Universities(Grant No.HIT.NSRIF.2013040)
文摘In this paper the design and implementation of sixth-order lowpass elliptic switched-capacitor filter( SCF) for interface circuit of Micro-Electro-Mechanical System( MEMS) sensor are presented. This work aims to lower total harmonic distortion( THD) without deteriorating other performances. After system design in Simulink,the filter is realized in transistor level and finally fabricated in Central Semiconductor Manufacturing Corporation( CSMC) 0.5 μm metal-oxide-semiconductor( CMOS) technology. Typical measured results are: it operates with 25: 1 clock-to-corner frequency ratio and a 10 k Hz maximum corner frequency. The maximum passband ripple is about 0.49 d B and the minimum stopband rejection is 40 d B for the temperature from-20 ℃to 80 ℃. For the 250 k Hz clock frequency setting,given the 1 k Hz,- 8 d BVrms input signal,the measured worst case THD is-64 d B. The active area of the chip is 2.8 mm2 with 8 pads. The analog power dissipation is10 m W from a 5 V power supply.
基金Supported by the Guangxi Special Program for Technological Innovation Guidance(No.GuiKeAC25069006).
文摘In this study,a fifth-degree cubature particle filter(5CPF)is proposed to address the limited estimation accuracy in traditional particle filter algorithms for bearings-only tracking(BOT).This algorithm calculates the recommended density function by introducing a fifth-degree cubature Kalman filter algorithm to guide particle sampling,which effectively alleviates the problem of particle degradation and significantly improves the estimation accuracy of the filter.However,the 5CPF algorithm exhibits high computational complexity,particularly in scenarios with a large number of particles.Therefore,we propose the extended Kalman filter(EKF)-5CPF algorithm,which employs an EKF to replace the time update step for each particle in the 5CPF.This enhances the algorithm’s real-time capability while maintaining the high precision advantage of the 5CPF algorithm.In addition,we construct bearing-only dual-station and single-motion station target tracking systems,and the filtering performances of 5CPF and EKF-5CPF algorithms under different conditions are analyzed.The results show that both the 5CPF algorithm and EKF-5CPF have strong robustness and can adapt to different noise environments.Furthermore,both algorithms significantly outperform traditional nonlinear filtering algorithms in terms of convergence speed,tracking accuracy,and overall stability.
基金supported by the National Natural Science Foundation of China(Grant Nos.11861050,11261037)the Natural Science Foundation of Inner Mongolia Autonomous Region,China(Grant No.2020LH01010)the Inner Mongolia Normal University Graduate Students Research and Innovation Fund(Grant No.CXJJS21119)。
文摘In this paper,we construct the rogue wave solutions of the sixth-order nonlinear Schrodinger equation on a background of Jacobian elliptic functions dn and cn by means of the nonlinearization of a spectral problem and Darboux transformation approach.The solutions we find present the dynamic phenomena of higher-order nonlinear wave equations.
基金the National Natural Science Foundation of China(91641107,91852116,12071470)Fundamental Research of Civil Aircraft(MJ-F-2012-04)of Ministry of Industrialization and Information of China.
文摘In this paper,we develop a new sixth-order WENO scheme by adopting a convex combina-tion of a sixth-order global reconstruction and four low-order local reconstructions.Unlike the classical WENO schemes,the associated linear weights of the new scheme can be any positive numbers with the only requirement that their sum equals one.Further,a very simple smoothness indicator for the global stencil is proposed.The new scheme can achieve sixth-order accuracy in smooth regions.Numerical tests in some one-and two-dimensional bench-mark problems show that the new scheme has a little bit higher resolution compared with the recently developed sixth-order WENO-Z6 scheme,and it is more efficient than the classical fifth-order WENO-JS5 scheme and the recently developed sixth-order WENO6-S scheme.
文摘We consider the singularly perturbed sixth-order Boussinesq-type equation, which describes the bidirectional propagation of small amplitude and long capillary gravity waves on the surface of shallow water for bond number (surface tension parameter) less than but very close to 1/3. The sufficient conditions of blow-up of solution to the Cauchy problem for this equation are given.
文摘By using Richardson extrapolation and fourth-order compact finite difference scheme on different scale grids, a sixth-order solution is computed on the coarse grid. Other three techniques are applied to obtain a sixth-order solution on the fine grid, and thus give out three kinds of Richardson extrapolation-based sixth order compact computation methods. By carefully analyzing the truncation errors respectively on 2D Poisson equation, we compare the accuracy of these three sixth order methods theoretically. Numerical results for two test problems are discussed.
基金supported by the National Science and Technology Council,Taiwan under grants NSTC 111-2221-E-019-047 and NSTC 112-2221-E-019-030.
文摘In this paper,an advanced satellite navigation filter design,referred to as the Variational Bayesian Maximum Correntropy Extended Kalman Filter(VBMCEKF),is introduced to enhance robustness and adaptability in scenarios with non-Gaussian noise and heavy-tailed outliers.The proposed design modifies the extended Kalman filter(EKF)for the global navigation satellite system(GNSS),integrating the maximum correntropy criterion(MCC)and the variational Bayesian(VB)method.This adaptive algorithm effectively reduces non-line-of-sight(NLOS)reception contamination and improves estimation accuracy,particularly in time-varying GNSS measurements.Experimental results show that the proposed method significantly outperforms conventional approaches in estimation accuracy under heavy-tailed outliers and non-Gaussian noise.By combining MCC with VB approximation for real-time noise covariance estimation using fixed-point iteration,the VBMCEKF achieves superior filtering performance in challenging GNSS conditions.The method’s adaptability and precision make it ideal for improving satellite navigation performance in stochastic environments.
基金Project supported by the National Key Research and Development Program of China(2021YFB3500600,2021YFB3500605)Natural Science Foundation of Jiangsu Province(BK20220365)+5 种基金Key R&D Program of Jiangsu Province(BE2022142)Natural Science Foundation of the Jiangsu Higher Education Institutions of China(22KJB610002)Priority Academic Program Development of Jiangsu Higher Education Institutions(PAPD)the Postgraduate Research&Practice Innovation Program of Jiangsu Province(KYCX23_1419)Science and Technology Plan of Yangzhou(YZ2022030,YZ2023020)the State Key Laboratory of Clean and Efficient Coal-fired Power Generation and Pollution Control(D2022FK098)。
文摘The integration of surface filtration and catalytic decomposition functions in catalytic bags enables the synergistic removal of multiple pollutants(such as dust,nitrogen oxide,acid gases,and dioxins)in a single reactor,thus effectively reducing the cost and operational difficulties associated with flue gas treatment.In this study,Mn-Ce-Sm-Sn(MCSS)catalysts were prepared and loaded onto hightemperature resistant polyimide(P84)filter through ultrasonic impregnation to create composite catalytic filter.The results demonstrate that the NO conversion rates of the composite catalytic filter consistently achieve above 95%within the temperature range of 160-260℃,with a chlorobenzene T_(90)value of 230℃.The ultrasonic impregnation method effectively loaded the catalyst onto the filter,ensuring high dispersion both on the surface and inside the filter.This increased exposure of catalyst active sites enhances the catalytic activity of the composite catalytic filter.Additionally,increasing the catalyst loading leads to a gradual decrease in permeability,an increase in pressure drops and the long residence time of the flue gas,thereby improving catalytic activity.Compared to ordinary impregnation methods,ultrasonic impregnation improves the bonding strength between the catalyst and filter,as well as the permeability of the composite catalytic filter under the same loading conditions.Overall,this study presents a novel approach to prepare composite catalytic filter for the simultaneous removal of NO and chlorobenzene at low temperatures.
文摘A medical image encryption is proposed based on the Fisher-Yates scrambling,filter diffusion and S-box substitution.First,chaotic sequence associated with the plaintext is generated by logistic-sine-cosine system,which is used for the scrambling,substitution and diffusion processes.The three-dimensional Fisher-Yates scrambling,S-box substitution and diffusion are employed for the first round of encryption.The chaotic sequence is adopted for secondary encryption to scramble the ciphertext obtained in the first round.Then,three-dimensional filter is applied to diffusion for further useful information hiding.The key to the algorithm is generated by the combination of hash value of plaintext image and the input parameters.It improves resisting ability of plaintext attacks.The security analysis shows that the algorithm is effective and efficient.It can resist common attacks.In addition,the good diffusion effect shows that the scheme can solve the differential attacks encountered in the transmission of medical images and has positive implications for future research.
基金supported by the Key Research and Development Program of Ningxia(Grant No.2023BCF01046)。
文摘Brackish water(BW)irrigation may cause soil quality deterioration and thereby a decrease in crop yields.Here we examined the impacts of applying gasification filter cake(GFC),intercropping with Portulaca oleracea(PO),and their combination on soil quality,nutrient uptake by plants and tomato yields under BW irrigation.The treatments evaluated included(i)freshwater irrigation(Control),(ii)BW irrigation,(iii)GFC application under BW irrigation(BW+GFC),(iv)intercropping with PO under BW irrigation(BW+PO),and(v)the combined application of GFC and PO under BW irrigation(BW+PO+GFC).Overall,the use of BW for irrigation resulted in a decline in both soil quality(assessed by a soil quality index(SQI)integrating a wide range of key soil properties including salinity,nutrient availability and microbial activities)and crop yields.Nevertheless,when subjected to BW irrigation,the application of GFC successfully prevented soil salinity.Additionally,the intercropping of PO decreased the soil sodium adsorption ratio and improved the absorption of nutrients by plants.As a result,the BW+GFC+PO treatment generally showed higher tomato yield as compared to other BW-related treatments(i.e.BW,BW+GFC and BW+PO).Compared to BW,the BW+GFC+PO treatment had an average increase of 24.7% in the total fruit yield of four Cropping Seasons.Furthermore,the BW+GFC+PO treatment consistently exhibited the highest fruit quality index(FQI).Taken together,the combined application of GFC and PO is effective in promoting soil quality and crop yields under BW irrigation.
基金Supported by the Natural Science Foundation of the Higher Education Institutions of Jiangsu Province(22KJB520012)the Research Project on Higher Education Reform in Jiangsu Province(2023JSJG781)the College Student Innovation and Entrepreneurship Training Program Project(202313571008Z)。
文摘Fault detection in industrial robot drive systems is a critical aspect of ensuring operational reliability and efficiency.To address the challenge of balancing accuracy and robustness in existing fault detection methods,this paper proposes an enhanced fault detection method based on the unscented Kalman filter(UKF).A comprehensive mathematical model of the brushless DC motor drive system is developed to provide a theoretical foundation for the design of subsequent fault detection methods.The conventional UKF estimation process is detailed,and its limitations in balancing estimation accuracy and robustness are addressed by introducing a dynamic,time-varying boundary layer.To further enhance detection performance,the method incorporates residual analysis using improved z-score and signal-tonoise ratio(SNR)metrics.Numerical simulations under both fault-free and faulty conditions demonstrate that the proposed approach achieves lower root mean square error(RMSE)in fault-free scenarios and provides reliable fault detection.These results highlight the potential of the proposed method to enhance the reliability and robustness of fault detection in industrial robot drive systems.
基金supported by the National Key R&D Program of China(No.2021YFB2011300)the Special Funds Project for the Transformation of Scientific and Technological Achievements of Jiangsu Province,China(No.BA2023039)+1 种基金the National Natural Science Foundation of China(No.52075262)the Fundamental Research Funds for the Central Universities,China(No.30922010706).
文摘The output feedback active disturbance rejection control of a valve-controlled cylinder electro-hydraulic servo system is investigated in this paper.First,a comprehensive nonlinear mathematical model that encompasses both matched and mismatched disturbances is formulated.Due to the fact that only position information can be measured,a linear Extended State Observer(ESO)is introduced to estimate unknown states and matched disturbances,while a dedicated disturbance observer is constructed to estimate mismatched disturbances.Different from the traditional observer results,the design of the disturbance observer used in this study is carried out under the constraint of output feedback.Furthermore,an output feedback nonlinear controller is proposed leveraging the aforementioned observers to achieve accurate trajectory tracking.To mitigate the inherent differential explosion problem of the traditional backstepping framework,a finite-time stable command filter is incorporated.Simultaneously,considering transient filtering errors,a set of error compensation signals are designed to counter their negative impact effectively.Theoretical analysis affirms that the proposed control strategy ensures the boundedness of all signals within the closed-loop system.Additionally,under the specific condition of only time-invariant disturbances in the system,the conclusion of asymptotic stability is established.Finally,the algorithm’s efficacy is validated through comparative experiments.
文摘Terrain Aided Navigation(TAN)technology has become increasingly important due to its effectiveness in environments where Global Positioning System(GPS)is unavailable.In recent years,TAN systems have been extensively researched for both aerial and underwater navigation applications.However,many TAN systems that rely on recursive Unmanned Aerial Vehicle(UAV)position estimation methods,such as Extended Kalman Filters(EKF),often face challenges with divergence and instability,particularly in highly non-linear systems.To address these issues,this paper proposes and investigates a hybrid two-stage TAN positioning system for UAVs that utilizes Particle Filter.To enhance the system’s robustness against uncertainties caused by noise and to estimate additional system states,a Fuzzy Particle Filter(FPF)is employed in the first stage.This approach introduces a novel terrain composite feature that enables a fuzzy expert system to analyze terrain non-linearities and dynamically adjust the number of particles in real-time.This design allows the UAV to be efficiently localized in GPS-denied environments while also reducing the computational complexity of the particle filter in real-time applications.In the second stage,an Error State Kalman Filter(ESKF)is implemented to estimate the UAV’s altitude.The ESKF is chosen over the conventional EKF method because it is more suitable for non-linear systems.Simulation results demonstrate that the proposed fuzzy-based terrain composite method achieves high positional accuracy while reducing computational time and memory usage.
基金supported in part by the National Natural Science Foundation of China(12171124,61933007)the Natural Science Foundation of Heilongjiang Province of China(ZD2022F003)+2 种基金the National High-End Foreign Experts Recruitment Plan of China(G2023012004L)the Royal Society of UKthe Alexander von Humboldt Foundation of Germany
文摘In this paper, the problem of cubature Kalman fusion filtering(CKFF) is addressed for multi-sensor systems under amplify-and-forward(AaF) relays. For the purpose of facilitating data transmission, AaF relays are utilized to regulate signal communication between sensors and filters. Here, the randomly varying channel parameters are represented by a set of stochastic variables whose occurring probabilities are permitted to exhibit bounded uncertainty. Employing the spherical-radial cubature principle, a local filter under AaF relays is initially constructed. This construction ensures and minimizes an upper bound of the filtering error covariance by designing an appropriate filter gain. Subsequently, the local filters are fused through the application of the covariance intersection fusion rule. Furthermore, the uniform boundedness of the filtering error covariance's upper bound is investigated through establishing certain sufficient conditions. The effectiveness of the proposed CKFF scheme is ultimately validated via a simulation experiment concentrating on a three-phase induction machine.
基金Supported by the Fundamental Research Funds for the Central Universities(ZYGX2021J008)。
文摘A novel substrate integrated microstrip to ultra-thin cavity filter transition operating in the W-band is proposed in this letter.The structure is a new method of connecting microstrip circuits and waveguide filters,and this new structure enables a planar integrated transition from microstrip lines to ultra-thin cavity filters,thereby reducing the size of the transition structure and achieving miniaturization.The structure includes a conventional tapered microstrip transition structure,which guides the electromagnetic field from the microstrip line to the reduced-height dielectric-filled waveguide,and an air-filled matching cavity which is placed between the dielectric-filled waveguide and the ultra-thin cavity filter.The heights of the microstrip line,the dielectric-filled waveguide and the ultra-thin cavity filter are the same,enabling seamless integration within a planar radio-frequency(RF)circuit.To facilitate testing,mature finline transition structures are integrated at both ends of the microstrip line during fabrications.The simulation results of the fabricated microstrip to ultra-thin cavity filter transition with the finline transition structure,with a passband of 91.5-96.5 GHz,has an insertion loss of less than 1.9 dB and a return loss lower than-20 dB.And the whole structure has also been measured which achieves an insertion loss less than 2.6 dB and a return loss lower than-15 dB within the filter's passband,including the additional insertion loss introduced by the finline transitions.Finally,a W-band compact up-conversion module is designed,and the test results show that after using the proposed structure,the module achieves 95 dBc suppression of the 84 GHz local oscillator.It is also demonstrated that the structure proposed in this letter achieves miniaturization of the system integration without compromising the filter performance.
文摘Filter capacitors play an important role in altern-ating current(AC)-line filtering for stabilizing voltage,sup-pressing harmonics,and improving power quality.However,traditional aluminum electrolytic capacitors(AECs)suffer from a large size,short lifespan,low power density,and poor reliability,which limits their use.In contrast,ultrafast supercapacitors(SCs)are ideal for replacing commercial AECs because of their extremely high power densities,fast charging and discharging,and excellent high-frequency re-sponse.We review the design principles and key parameters for ultrafast supercapacitors and summarize research pro-gress in recent years from the aspects of electrode materials,electrolytes,and device configurations.The preparation,structures,and frequency response performance of electrode materials mainly consisting of carbon materials such as graphene and carbon nanotubes,conductive polymers,and transition metal compounds,are focused on.Finally,future research directions for ultrafast SCs are suggested.
基金supported in part by the National Natural Science Foundation of China(61873348,6230 3266,62273200)JSPS(Japan Society for the Promotion of Science) KAKENHI(22H03998,23K25252)
文摘Dear Editor,This letter presents an improved repetitive controller(IRC) that uses a complex-coefficient filter to enhance the tracking performance of a system for periodic signals. Compared with the low-pass filter used in the conventional repetitive controller(CRC), the complex-coefficient filter causes less change in the phase and amplitude of a signal at the frequencies of the periodic signal, especially at the fundamental frequency, when the two filters have the same cutofffrequency.
基金supported by the National Natural Science(No.U19A2063)the Jilin Provincial Development Program of Science and Technology (No.20230201080GX)the Jilin Province Education Department Scientific Research Project (No.JJKH20230851KJ)。
文摘The visual noise of each light intensity area is different when the image is drawn by Monte Carlo method.However,the existing denoising algorithms have limited denoising performance under complex lighting conditions and are easy to lose detailed information.So we propose a rendered image denoising method with filtering guided by lighting information.First,we design an image segmentation algorithm based on lighting information to segment the image into different illumination areas.Then,we establish the parameter prediction model guided by lighting information for filtering(PGLF)to predict the filtering parameters of different illumination areas.For different illumination areas,we use these filtering parameters to construct area filters,and the filters are guided by the lighting information to perform sub-area filtering.Finally,the filtering results are fused with auxiliary features to output denoised images for improving the overall denoising effect of the image.Under the physically based rendering tool(PBRT)scene and Tungsten dataset,the experimental results show that compared with other guided filtering denoising methods,our method improves the peak signal-to-noise ratio(PSNR)metrics by 4.2164 dB on average and the structural similarity index(SSIM)metrics by 7.8%on average.This shows that our method can better reduce the noise in complex lighting scenesand improvethe imagequality.
文摘High-selectivity common-mode(CM)and differential-mode(DM)reflectionless balanced bandpass filters(BBPFs)are proposed in this article.By loading absorption networks at single/both ends of the basic ring resonator,input-/two-port wideband CM and DM reflectionless performance,wideband filtering performance and all-stop CM suppression are obtained.The absorption network composed of K-sections of coupled-lines(CLs)terminated with grounded resistors can not only extend the filtering performance to high order,but also realize wideband absorption of CM noise and out-of-band DM signals.Absorptive stubs are loaded at ports to increase the design flexibility and enhance the absorption.As for the input-reflectionless type,multiple independently controlled transmission zeros(TZs)are obtained by the TZ control network to improves the selectivity and out-of-band rejection.A set of 2 GHz micro-strip BBPFs are designed and measured,which shows simultaneous CM and DM absorption performance.
基金supported by the National Natural Science Foundation of China under Grant No.62172132.
文摘The surge of large-scale models in recent years has led to breakthroughs in numerous fields,but it has also introduced higher computational costs and more complex network architectures.These increasingly large and intricate networks pose challenges for deployment and execution while also exacerbating the issue of network over-parameterization.To address this issue,various network compression techniques have been developed,such as network pruning.A typical pruning algorithm follows a three-step pipeline involving training,pruning,and retraining.Existing methods often directly set the pruned filters to zero during retraining,significantly reducing the parameter space.However,this direct pruning strategy frequently results in irreversible information loss.In the early stages of training,a network still contains much uncertainty,and evaluating filter importance may not be sufficiently rigorous.To manage the pruning process effectively,this paper proposes a flexible neural network pruning algorithm based on the logistic growth differential equation,considering the characteristics of network training.Unlike other pruning algorithms that directly reduce filter weights,this algorithm introduces a three-stage adaptive weight decay strategy inspired by the logistic growth differential equation.It employs a gentle decay rate in the initial training stage,a rapid decay rate during the intermediate stage,and a slower decay rate in the network convergence stage.Additionally,the decay rate is adjusted adaptively based on the filter weights at each stage.By controlling the adaptive decay rate at each stage,the pruning of neural network filters can be effectively managed.In experiments conducted on the CIFAR-10 and ILSVRC-2012 datasets,the pruning of neural networks significantly reduces the floating-point operations while maintaining the same pruning rate.Specifically,when implementing a 30%pruning rate on the ResNet-110 network,the pruned neural network not only decreases floating-point operations by 40.8%but also enhances the classification accuracy by 0.49%compared to the original network.
