Energy shortage has become one of themost concerning issues in the world today,and improving energy utilization efficiency is a key area of research for experts and scholars worldwide.Small-diameter heat exchangers of...Energy shortage has become one of themost concerning issues in the world today,and improving energy utilization efficiency is a key area of research for experts and scholars worldwide.Small-diameter heat exchangers offer advantages such as reduced material usage,lower refrigerant charge,and compact structure.However,they also face challenges,including increased refrigerant pressure drop and smaller heat transfer area inside the tubes.This paper combines the advantages and disadvantages of both small and large-diameter tubes and proposes a combined-diameter heat exchanger,consisting of large and small diameters,for use in the indoor units of split-type air conditioners.There are relatively few studies in this area.In this paper,A theoretical and numerical computation method is employed to establish a theoretical-numerical calculation model,and its reliability is verified through experiments.Using this model,the optimal combined diameters and flow path design for a combined-diameter heat exchanger using R32 as the working fluid are derived.The results show that the heat transfer performance of all combined diameter configurations improves by 2.79%to 8.26%compared to the baseline design,with the coefficient of performance(COP)increasing from 4.15 to 4.27~4.5.These designs can save copper material,but at the cost of an increase in pressure drop by 66.86%to 131.84%.The scheme IIIH,using R32,is the optimal combined-diameter and flow path configuration that balances both heat transfer performance and economic cost.展开更多
This study addresses the energy-intensive challenge of small-scale biogas upgrading by optimizing a chemical absorption process employing methyl diethanolamine(MDEA).Focusing on a typical distributed application of 30...This study addresses the energy-intensive challenge of small-scale biogas upgrading by optimizing a chemical absorption process employing methyl diethanolamine(MDEA).Focusing on a typical distributed application of 300 Nm^(3)/d,we developed an integrated simulation-optimization framework using Aspen HYSYS 14.0 to systematically evaluate the effects of critical operating parameters—absorption pressure,MDEA concentration,flow rate,temperature,number of trays,and reboiler duty—on methane purity and energy consumption.The key finding is the identification of an optimal parameter set:absorption pressure of 1200 kPa,MDEA concentration of 20mol%,lean flow rate of 2.5 kmol/h,temperature of 298.15 K,20 absorber trays,10 regenerator trays,and a reboiler duty of 4 kW,which enabled the product gas to achieve a high CH4 concentration of 97mol%,compliant with pipeline standards.A detailed energy consumption analysis revealed that the reboiler is the most energy-intensive unit,accounting for 75.40%of the total 5.29 kW energy consumption,followed by the gas compressor(23.38%).The specific energy consumption for CH4 recovery and the Energy Consumption Index(ECI)were quantified at 0.8852 kWh/kg CH_(4)and 6.82,respectively.This work provides a validated optimization strategy and critical energy breakdown,offering practical guidance for enhancing the technical and economic viability of small-scale,centralized biogas purification systems.展开更多
Based on the Fluent numerical simulation method,this study systematically analyzed the structural parameters of the spiral tube heat exchanger and the influence of the external baffle on its heat transfer performance....Based on the Fluent numerical simulation method,this study systematically analyzed the structural parameters of the spiral tube heat exchanger and the influence of the external baffle on its heat transfer performance.The results show that when the equivalent diameter of the spiral tube increased from 16.68 to 21.23 mm,its surface heat transfer coefficient decreased from 22,040 to 17,230 W/m^(2)⋅K,and the outlet air temperature dropped from 822.3 to 807.3 K.However,the pressure loss decreased from 2.692 to 0.958 kPa.which reveals the contradiction between the heat transfer efficiency and the flow resistance.By adding a baffle to enhance the turbulent disturbance,the wall heat flux density is increased by 21.17%,the surface heat transfer coefficient is increased by 12.1%,and the outlet temperature is optimized,which verifies the significant improvement of the heat transfer performance by the countercurrent design.Comprehensive research shows that the collaborative optimization of spiral tube equivalent diameter parameters and baffle flow control is the key to improve the comprehensive performance of heat exchanger.Theresearch results provide a theoretical basis for energy-saving design of industrial heat exchangers.展开更多
In order to improve the efficiency of cloud-based web services,an improved plant growth simulation algorithm scheduling model.This model first used mathematical methods to describe the relationships between cloud-base...In order to improve the efficiency of cloud-based web services,an improved plant growth simulation algorithm scheduling model.This model first used mathematical methods to describe the relationships between cloud-based web services and the constraints of system resources.Then,a light-induced plant growth simulation algorithm was established.The performance of the algorithm was compared through several plant types,and the best plant model was selected as the setting for the system.Experimental results show that when the number of test cloud-based web services reaches 2048,the model being 2.14 times faster than PSO,2.8 times faster than the ant colony algorithm,2.9 times faster than the bee colony algorithm,and a remarkable 8.38 times faster than the genetic algorithm.展开更多
The performance and efficiency of hydraulic excavators heavily depend on the design and optimization of their working devices.The working device,which consists of the boom,arm,and bucket,plays a crucial role in determ...The performance and efficiency of hydraulic excavators heavily depend on the design and optimization of their working devices.The working device,which consists of the boom,arm,and bucket,plays a crucial role in determining the machine's digging capacity,stability,and overall operational efficiency.This paper presents a comprehensive study on the dynamics simulation and optimization of hydraulic excavator working devices.The paper outlines the fundamental principles of dynamic modeling,incorporating multi-body dynamics and hydraulic system analysis.It further explores various simulation techniques to evaluate the performance of the working device under varying operational conditions,including load and hydraulic system effects.The study also addresses performance optimization,focusing on multi-objective optimization methods that balance multiple factors such as energy efficiency,speed,and load capacity.Additionally,the paper discusses key factors influencing performance,such as mechanical design,material properties,and operational conditions.The results of the dynamic simulations and optimization analyses demonstrate potential improvements in operational efficiency and system stability,providing a valuable framework for the design and enhancement of hydraulic excavator working devices.展开更多
In response to the deficiencies of commonly used optimization methods for assembly lines,a production demand-oriented optimization method for assembly lines is proposed.Taking a certain compressor assembly line as an ...In response to the deficiencies of commonly used optimization methods for assembly lines,a production demand-oriented optimization method for assembly lines is proposed.Taking a certain compressor assembly line as an example,the production rhythm and the number of workstations are calculated based on production requirements and working systems.With assembly rhythm and smoothing index as optimization goals,an improved particle swarm optimization algorithm is employed for process allocation.Subsequently,Flexsim simulation is used to analyze the assembly line.The final results show that after optimization using the improved particle swarm algorithm,the assembly line balance rate increased from 71.1%to 85.9%,and the assembly line smoothing index decreased from 47.4 to 29.8,significantly enhancing assembly efficiency.This demonstrates the effectiveness of the proposed optimization method for the assembly line and provides a reference for other products in the same industry.展开更多
Fluxgate current sensors(FGCSs)are increasingly employed in power systems due to their high-precision characteristics,yet their measurement flexibility remains constrained by conventional closed-core designs.To addres...Fluxgate current sensors(FGCSs)are increasingly employed in power systems due to their high-precision characteristics,yet their measurement flexibility remains constrained by conventional closed-core designs.To address this limitation,we proposed a split-core sensor structure comprising four magnetic core strips,which achieved non-intrusive current measurement while maintaining detection accuracy.An analytical model of the induced electromotive force was established based on the probe’s geometric configuration,followed by finite element simulations to optimize key parameters including core radius,core width,excitation coil turns,and sensing coil configuration.A complete prototype integrating the measurement probe,excitation circuit,and signal processing circuitry was developed and experimentally validated.The experimental results show a sensitivity of 0.1099 V/A,a hysteresis error of 0.559%,and a repeatability error of 1.574%over a measurement range of±10 A.After polynomial fitting-based error compensation,the nonlinearity error was reduced to 0.208%,achieving performance comparable to closed-core sensors.This work provided a practical solution for applications demanding both high measurement accuracy and installation flexibility.展开更多
Gassy soils are distributed in relatively shallow layers the Quaternary deposit in Hangzhou Bay area. The shallow gassy soils significantly affect the construction of underground projects. Proper characterization of s...Gassy soils are distributed in relatively shallow layers the Quaternary deposit in Hangzhou Bay area. The shallow gassy soils significantly affect the construction of underground projects. Proper characterization of spatial distribution of shallow gassy soils is indispensable prior to construction of underground projects in the area. Due to the costly conditions required in the site investigation for gassy soils, only a limited number of gas pressure data can be obtained in engineering practice, which leads to the uncertainty in characterizing spatial distribution of gassy soils. Determining the number of boreholes for investigating gassy soils and their corresponding locations is pivotal to reducing construction risk induced by gassy soils. However, this primarily relies on the engineering experience in the current site investigation practice. This study develops a probabilistic site investigation optimization method for planning investigation schemes (including the number and locations of boreholes) of gassy soils based on the conditional random field and Monte Carlo simulation. The proposed method aims to provide an optimal investigation scheme before the site investigation based on prior knowledge. Finally, the proposed approach is illustrated using a case study.展开更多
Traditionally,a continuous-wave(CW)signal is used to simulate RF circuits during the design procedure,while the fabricated circuits are measured by modulated signals in the test phase,because modulated signals are use...Traditionally,a continuous-wave(CW)signal is used to simulate RF circuits during the design procedure,while the fabricated circuits are measured by modulated signals in the test phase,because modulated signals are used in reality.It is almost impossible to use a CW signal to predict system performances,such as error vector magnitude(EVM),bit error rate(BER),etc.,of a transceiver front-end when dealing with complex modulated signals.This paper develops an integrated system evaluation engine(ISEE)to evaluate the system performances of a transceiver front-end or its sub-circuits.This crossdomain simulation platform is based on Matlab,advanced design system(ADS),and Cadence simulators to link the baseband signals and transceiver frond-end.An orthogonal frequency division multiplex(OFDM)modem is implemented in Matlab for evaluating the system performances.The modulated baseband signal from Matlab is dynamically fed into ADS,which includes transceiver front-end for co-simulation.The sub-block circuits of the transceiver front-end can be implemented using ADS and Cadence simulators.After system-level circuit simulation in ADS,the output signal is dynamically delivered to Matlab for demodulation.To simplify the use of the co-simulation platform,a graphical user interface(GUI)is constructed using Matlab.The parameters of the OFDM signals can be easily reconfigured on the GUI to simulate RF circuits with different modulation schemes.To demonstrate the effectiveness of the ISEE,a 3.5 GHz power amplifier is simulated and characterized using 20 MHz 16-and 64-QAM OFDM signals.展开更多
Liquid hydrogen has attracted much attention due to its high energy storage density and suitability for long-distance transportation.An efficient hydrogen liquefaction process is the key to obtaining liquid hydrogen.I...Liquid hydrogen has attracted much attention due to its high energy storage density and suitability for long-distance transportation.An efficient hydrogen liquefaction process is the key to obtaining liquid hydrogen.In an effort to determine the parameter optimization of the hydrogen liquefaction process,this paper employed process simulation software Aspen HYSYS to simulate the hydrogen liquefaction process.By establishing a dynamic model of the unit module,this study carried out dynamic simulation optimization based on the steady-state process and process parameters of the hydrogen liquefaction process and analyzed the dynamic characteristics of the process.Based on the pressure drop characteristic experiment,an equation for the pressure drop in the heat exchanger was proposed.The heat transfer of hydrogen conversion was simulated and analyzed,and its accuracy was verified by comparison with the literature.The dynamic simulation of a plate-fin heat exchanger was carried out by coupling heat transfer simulation and the pressure drop experiment.The results show that the increase in inlet temperature(5℃and 10℃)leads to an increase in specific energy consumption(0.65%and 1.29%,respectively)and a decrease in hydrogen liquefaction rate(0.63%and 2.88%,respectively).When the inlet pressure decreases by 28.57%,the hydrogen temperature of the whole liquefaction process decreases and the specific energy consumption increases by 52.94%.The research results are of great significance for improving the operating efficiency of the refrigeration cycle and guiding the actual liquid hydrogen production.展开更多
In recent years,three-dimensional reconstruction technologies that employ multiple cameras have continued to evolve significantly,enabling remote collaboration among users in extended Reality(XR)environments.In additi...In recent years,three-dimensional reconstruction technologies that employ multiple cameras have continued to evolve significantly,enabling remote collaboration among users in extended Reality(XR)environments.In addition,methods for deploying multiple cameras for motion capture of users(e.g.,performers)are widely used in computer graphics.As the need to minimize and optimize the number of cameras grows to reduce costs,various technologies and research approaches focused on Optimal Camera Placement(OCP)are continually being proposed.However,as most existing studies assume homogeneous camera setups,there is a growing demand for studies on heterogeneous camera setups.For instance,technical demands keep emerging in scenarios with minimal camera configurations,especially regarding cost factors,the physical placement of cameras given the spatial structure,and image capture strategies for heterogeneous cameras,such as high-resolution RGB cameras and depth cameras.In this study,we propose a pre-visualization and simulation method for the optimal placement of heterogeneous cameras in XR environments,accounting for both the specifications of heterogeneous cameras(e.g.,field of view)and the physical configuration(e.g.,wall configuration)in real-world spaces.The proposed method performs a visibility analysis of cameras by considering each camera’s field-of-view volume,resolution,and unique characteristics,along with physicalspace constraints.This approach enables the optimal position and rotation of each camera to be recommended,along with the minimum number of cameras required.In the results of our study conducted in heterogeneous camera combinations,the proposed method achieved 81.7%~82.7%coverage of the target visual information using only 2~3 cameras.In contrast,single(or homogeneous)-typed cameras were required to use 11 cameras for 81.6%coverage.Accordingly,we found that camera deployment resources can be reduced with the proposed approaches.展开更多
Natural gas hydrate widely exists in the South China Sea as clean energy.A three-phase transition layer widely exists in low permeability Class I hydrates in the Shenhu offshore area.Therefore,taking into account the ...Natural gas hydrate widely exists in the South China Sea as clean energy.A three-phase transition layer widely exists in low permeability Class I hydrates in the Shenhu offshore area.Therefore,taking into account the low-permeability characteristics with an average permeability of 5.5 mD and moderate heterogeneity,a 3-D geological model of heterogeneous Class I hydrate reservoirs with three-phase transition layers is established by Kriging interpolation and stochastic modeling method,and a numerical simulation model is used to describe the depressurization production performance of the reservoir.With the development of depressurization,a specific range of complete decomposition zones appear both in the hydrate and transition layers.The entire decomposition zone of the whole reservoir tends to outward and upward diffusion.There is apparent methane escape in the three-phase transition layer.Due to the improvement of local permeability caused by the phase transition of hydrate dissociation,some methane accumulation occurs at the bottom of the hydrate layer,forming a local methane enrichment zone.The methane migration trends in reservoirs are mainly characterized by movement toward production wells and hydrate layers under the influence of gravity.However,due to the permeability limitation of hydrate reservoirs,many fluids have not been effectively produced and remain in the reservoir.Therefore,to improve the effective pressure drop of the reservoir,the perforation method and pressure reduction method were optimized by analyzing the influencing factors based on the gas production rate.The comparative study demonstrates that perforating through the free gas layer combined with one-time depressurization can enhance the effective depressurization and improve production performance.The gas production rate from perforating through the free gas layer can be twice as high as that from perforating through the transition layer.This study can provide theoretical support for the utilization of marine energy.展开更多
Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing addit...Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing additive-induced defects,and alleviating residual stress and deformation,all of which are critical for enhancing the mechanical performance of the manufactured parts.Integrating interlayer friction stir processing(FSP)into WAAM significantly enhances the quality of deposited materials.However,numerical simulation research focusing on elucidating the associated thermomechanical coupling mechanisms remains insufficient.A comprehensive numerical model was developed to simulate the thermomechanical coupling behavior in friction stir-assisted WAAM.The influence of post-deposition FSP on the coupled thermomechanical response of the WAAM process was analyzed quantitatively.Moreover,the residual stress distribution and deformation behavior under both single-layer and multilayer deposition conditions were investigated.Thermal analysis of different deposition layers in WAAM and friction stir-assisted WAAM was conducted.Results show that subsequent layer deposition induces partial remelting of the previously solidified layer,whereas FSP does not cause such remelting.Furthermore,thermal stress and deformation analysis confirm that interlayer FSP effectively mitigates residual stresses and distortion in WAAM components,thereby improving their structural integrity and mechanical properties.展开更多
Atomistic simulations were adopted to study the solute segregation effect on dislocation transmutation across the{1012}twin boundaries in magnesium.For pure magnesium,the dislocation-twin reaction resulted in the form...Atomistic simulations were adopted to study the solute segregation effect on dislocation transmutation across the{1012}twin boundaries in magnesium.For pure magnesium,the dislocation-twin reaction resulted in the formation of sessile dislocations accompanied by the fast migration of the twin boundary,and no〈c+a〉dislocation occurred.With Al segregation,instead,two basal dislocations transmuted into one prismatic〈c+a〉dislocation in the twin.Twin migration was significantly impeded,and the resultant twin disconnections stayed localized and had a higher step character than in pure Mg.To reveal the mechanism of the effect of solute segregation,the Peierls barriers of twin disconnections were calculated,and the dynamic evolutions of twin disconnection dipoles were simulated.The results suggested that Al segregation softened the Peierls barrier of twin disconnections but imposed a high pinning force on twin disconnections,thus attenuating their mobility.Moreover,given the same Al segregation,the twin disconnection dipole with a higher step showed greater stability,which explained the presence of localized twin disconnections with a higher step in the cases with Al segregation than in pure magnesium.The solute segregation induced low mobility of twin disconnections contributed to the occurrence of〈c+a〉dislocations.展开更多
The rapid advancement of machine learning based tight-binding Hamiltonian(MLTB)methods has opened new avenues for efficient and accurate electronic structure simulations,particularly in large-scale systems and long-ti...The rapid advancement of machine learning based tight-binding Hamiltonian(MLTB)methods has opened new avenues for efficient and accurate electronic structure simulations,particularly in large-scale systems and long-time scenarios.This review begins with a concise overview of traditional tight-binding(TB)models,including both(semi-)empirical and first-principles approaches,establishing the foundation for understanding MLTB developments.We then present a systematic classification of existing MLTB methodologies,grouped into two major categories:direct prediction of TB Hamiltonian elements and inference of empirical parameters.A comparative analysis with other ML-based electronic structure models is also provided,highlighting the advancement of MLTB approaches.Finally,we explore the emerging MLTB application ecosystem,highlighting how the integration of MLTB models with a diverse suite of post-processing tools from linear-scaling solvers to quantum transport frameworks and molecular dynamics interfaces is essential for tackling complex scientific problems across different domains.The continued advancement of this integrated paradigm promises to accelerate materials discovery and open new frontiers in the predictive simulation of complex quantum phenomena.展开更多
Vitrimers belong to a class of polymeric materials capable of bond exchange reactions,showing great promise for environmental protection and sustainable development.However,studies on the coupling mechanism between th...Vitrimers belong to a class of polymeric materials capable of bond exchange reactions,showing great promise for environmental protection and sustainable development.However,studies on the coupling mechanism between the bond exchange kinetics and segmental dynamics near the glass transition temperature(T_(g))remain scarce.Herein,we employed molecular dynamics simulations to investigate the dynamic heterogeneity of the segment motion and bond exchange in vitrimers.The simulation results revealed that the bond exchange energy barrier exerts a much stronger influence on the bond exchange kinetics than on the segmental dynamics.At lower temperatures,slower segmental relaxation further constraind the bond exchange rate.Additionally,increasing the bond exchange energy barrier markedly enhanced the dynamic heterogeneity of segment motion.A close correlation was observed between heterogeneity and bond exchange.This study elucidated the coupling mechanism between bond exchange and segmental dynamics at the molecular scale,thereby providing a theoretical basis for designing vitrimer materials with tunable dynamic properties.展开更多
基金supported by Supported by the Scientific Research Foundation for High-Level Talents of Zhoukou Normal University(ZKNUC2024018).
文摘Energy shortage has become one of themost concerning issues in the world today,and improving energy utilization efficiency is a key area of research for experts and scholars worldwide.Small-diameter heat exchangers offer advantages such as reduced material usage,lower refrigerant charge,and compact structure.However,they also face challenges,including increased refrigerant pressure drop and smaller heat transfer area inside the tubes.This paper combines the advantages and disadvantages of both small and large-diameter tubes and proposes a combined-diameter heat exchanger,consisting of large and small diameters,for use in the indoor units of split-type air conditioners.There are relatively few studies in this area.In this paper,A theoretical and numerical computation method is employed to establish a theoretical-numerical calculation model,and its reliability is verified through experiments.Using this model,the optimal combined diameters and flow path design for a combined-diameter heat exchanger using R32 as the working fluid are derived.The results show that the heat transfer performance of all combined diameter configurations improves by 2.79%to 8.26%compared to the baseline design,with the coefficient of performance(COP)increasing from 4.15 to 4.27~4.5.These designs can save copper material,but at the cost of an increase in pressure drop by 66.86%to 131.84%.The scheme IIIH,using R32,is the optimal combined-diameter and flow path configuration that balances both heat transfer performance and economic cost.
基金funded by Shenzhen Science and Technology Program,grant number No.ZDSYS20230626091400001No.KCXST20221021111609024No.KCXFZ20240903093459001.
文摘This study addresses the energy-intensive challenge of small-scale biogas upgrading by optimizing a chemical absorption process employing methyl diethanolamine(MDEA).Focusing on a typical distributed application of 300 Nm^(3)/d,we developed an integrated simulation-optimization framework using Aspen HYSYS 14.0 to systematically evaluate the effects of critical operating parameters—absorption pressure,MDEA concentration,flow rate,temperature,number of trays,and reboiler duty—on methane purity and energy consumption.The key finding is the identification of an optimal parameter set:absorption pressure of 1200 kPa,MDEA concentration of 20mol%,lean flow rate of 2.5 kmol/h,temperature of 298.15 K,20 absorber trays,10 regenerator trays,and a reboiler duty of 4 kW,which enabled the product gas to achieve a high CH4 concentration of 97mol%,compliant with pipeline standards.A detailed energy consumption analysis revealed that the reboiler is the most energy-intensive unit,accounting for 75.40%of the total 5.29 kW energy consumption,followed by the gas compressor(23.38%).The specific energy consumption for CH4 recovery and the Energy Consumption Index(ECI)were quantified at 0.8852 kWh/kg CH_(4)and 6.82,respectively.This work provides a validated optimization strategy and critical energy breakdown,offering practical guidance for enhancing the technical and economic viability of small-scale,centralized biogas purification systems.
基金supported by the Jing-Jin-Ji Regional Integrated Environmental Improvement-National Science and Technology Major Project(No.2024ZD1200400).
文摘Based on the Fluent numerical simulation method,this study systematically analyzed the structural parameters of the spiral tube heat exchanger and the influence of the external baffle on its heat transfer performance.The results show that when the equivalent diameter of the spiral tube increased from 16.68 to 21.23 mm,its surface heat transfer coefficient decreased from 22,040 to 17,230 W/m^(2)⋅K,and the outlet air temperature dropped from 822.3 to 807.3 K.However,the pressure loss decreased from 2.692 to 0.958 kPa.which reveals the contradiction between the heat transfer efficiency and the flow resistance.By adding a baffle to enhance the turbulent disturbance,the wall heat flux density is increased by 21.17%,the surface heat transfer coefficient is increased by 12.1%,and the outlet temperature is optimized,which verifies the significant improvement of the heat transfer performance by the countercurrent design.Comprehensive research shows that the collaborative optimization of spiral tube equivalent diameter parameters and baffle flow control is the key to improve the comprehensive performance of heat exchanger.Theresearch results provide a theoretical basis for energy-saving design of industrial heat exchangers.
基金Shanxi Province Higher Education Science and Technology Innovation Fund Project(2022-676)Shanxi Soft Science Program Research Fund Project(2016041008-6)。
文摘In order to improve the efficiency of cloud-based web services,an improved plant growth simulation algorithm scheduling model.This model first used mathematical methods to describe the relationships between cloud-based web services and the constraints of system resources.Then,a light-induced plant growth simulation algorithm was established.The performance of the algorithm was compared through several plant types,and the best plant model was selected as the setting for the system.Experimental results show that when the number of test cloud-based web services reaches 2048,the model being 2.14 times faster than PSO,2.8 times faster than the ant colony algorithm,2.9 times faster than the bee colony algorithm,and a remarkable 8.38 times faster than the genetic algorithm.
文摘The performance and efficiency of hydraulic excavators heavily depend on the design and optimization of their working devices.The working device,which consists of the boom,arm,and bucket,plays a crucial role in determining the machine's digging capacity,stability,and overall operational efficiency.This paper presents a comprehensive study on the dynamics simulation and optimization of hydraulic excavator working devices.The paper outlines the fundamental principles of dynamic modeling,incorporating multi-body dynamics and hydraulic system analysis.It further explores various simulation techniques to evaluate the performance of the working device under varying operational conditions,including load and hydraulic system effects.The study also addresses performance optimization,focusing on multi-objective optimization methods that balance multiple factors such as energy efficiency,speed,and load capacity.Additionally,the paper discusses key factors influencing performance,such as mechanical design,material properties,and operational conditions.The results of the dynamic simulations and optimization analyses demonstrate potential improvements in operational efficiency and system stability,providing a valuable framework for the design and enhancement of hydraulic excavator working devices.
文摘In response to the deficiencies of commonly used optimization methods for assembly lines,a production demand-oriented optimization method for assembly lines is proposed.Taking a certain compressor assembly line as an example,the production rhythm and the number of workstations are calculated based on production requirements and working systems.With assembly rhythm and smoothing index as optimization goals,an improved particle swarm optimization algorithm is employed for process allocation.Subsequently,Flexsim simulation is used to analyze the assembly line.The final results show that after optimization using the improved particle swarm algorithm,the assembly line balance rate increased from 71.1%to 85.9%,and the assembly line smoothing index decreased from 47.4 to 29.8,significantly enhancing assembly efficiency.This demonstrates the effectiveness of the proposed optimization method for the assembly line and provides a reference for other products in the same industry.
基金supported by Yunnan Fundamental Research Projects(No.202301AT070181)Yunnan Fundamental Research Projects(No.202401CF070126)+1 种基金Xingdian Talent Support Program of Yunnan Province(No.KKRD202203070)Yunnan High level Science and Technology Talents and Innovation Team Selection Special Project(No.202405AS350001).
文摘Fluxgate current sensors(FGCSs)are increasingly employed in power systems due to their high-precision characteristics,yet their measurement flexibility remains constrained by conventional closed-core designs.To address this limitation,we proposed a split-core sensor structure comprising four magnetic core strips,which achieved non-intrusive current measurement while maintaining detection accuracy.An analytical model of the induced electromotive force was established based on the probe’s geometric configuration,followed by finite element simulations to optimize key parameters including core radius,core width,excitation coil turns,and sensing coil configuration.A complete prototype integrating the measurement probe,excitation circuit,and signal processing circuitry was developed and experimentally validated.The experimental results show a sensitivity of 0.1099 V/A,a hysteresis error of 0.559%,and a repeatability error of 1.574%over a measurement range of±10 A.After polynomial fitting-based error compensation,the nonlinearity error was reduced to 0.208%,achieving performance comparable to closed-core sensors.This work provided a practical solution for applications demanding both high measurement accuracy and installation flexibility.
文摘Gassy soils are distributed in relatively shallow layers the Quaternary deposit in Hangzhou Bay area. The shallow gassy soils significantly affect the construction of underground projects. Proper characterization of spatial distribution of shallow gassy soils is indispensable prior to construction of underground projects in the area. Due to the costly conditions required in the site investigation for gassy soils, only a limited number of gas pressure data can be obtained in engineering practice, which leads to the uncertainty in characterizing spatial distribution of gassy soils. Determining the number of boreholes for investigating gassy soils and their corresponding locations is pivotal to reducing construction risk induced by gassy soils. However, this primarily relies on the engineering experience in the current site investigation practice. This study develops a probabilistic site investigation optimization method for planning investigation schemes (including the number and locations of boreholes) of gassy soils based on the conditional random field and Monte Carlo simulation. The proposed method aims to provide an optimal investigation scheme before the site investigation based on prior knowledge. Finally, the proposed approach is illustrated using a case study.
基金supported by the Project of Hetao Shenzhen-Hong Kong Science and Technology Innovation Cooperation Zone(No.HZQB-KCZYB-2020083).
文摘Traditionally,a continuous-wave(CW)signal is used to simulate RF circuits during the design procedure,while the fabricated circuits are measured by modulated signals in the test phase,because modulated signals are used in reality.It is almost impossible to use a CW signal to predict system performances,such as error vector magnitude(EVM),bit error rate(BER),etc.,of a transceiver front-end when dealing with complex modulated signals.This paper develops an integrated system evaluation engine(ISEE)to evaluate the system performances of a transceiver front-end or its sub-circuits.This crossdomain simulation platform is based on Matlab,advanced design system(ADS),and Cadence simulators to link the baseband signals and transceiver frond-end.An orthogonal frequency division multiplex(OFDM)modem is implemented in Matlab for evaluating the system performances.The modulated baseband signal from Matlab is dynamically fed into ADS,which includes transceiver front-end for co-simulation.The sub-block circuits of the transceiver front-end can be implemented using ADS and Cadence simulators.After system-level circuit simulation in ADS,the output signal is dynamically delivered to Matlab for demodulation.To simplify the use of the co-simulation platform,a graphical user interface(GUI)is constructed using Matlab.The parameters of the OFDM signals can be easily reconfigured on the GUI to simulate RF circuits with different modulation schemes.To demonstrate the effectiveness of the ISEE,a 3.5 GHz power amplifier is simulated and characterized using 20 MHz 16-and 64-QAM OFDM signals.
基金supported by the National Natural Science Foundation of China,China(No.52474088).
文摘Liquid hydrogen has attracted much attention due to its high energy storage density and suitability for long-distance transportation.An efficient hydrogen liquefaction process is the key to obtaining liquid hydrogen.In an effort to determine the parameter optimization of the hydrogen liquefaction process,this paper employed process simulation software Aspen HYSYS to simulate the hydrogen liquefaction process.By establishing a dynamic model of the unit module,this study carried out dynamic simulation optimization based on the steady-state process and process parameters of the hydrogen liquefaction process and analyzed the dynamic characteristics of the process.Based on the pressure drop characteristic experiment,an equation for the pressure drop in the heat exchanger was proposed.The heat transfer of hydrogen conversion was simulated and analyzed,and its accuracy was verified by comparison with the literature.The dynamic simulation of a plate-fin heat exchanger was carried out by coupling heat transfer simulation and the pressure drop experiment.The results show that the increase in inlet temperature(5℃and 10℃)leads to an increase in specific energy consumption(0.65%and 1.29%,respectively)and a decrease in hydrogen liquefaction rate(0.63%and 2.88%,respectively).When the inlet pressure decreases by 28.57%,the hydrogen temperature of the whole liquefaction process decreases and the specific energy consumption increases by 52.94%.The research results are of great significance for improving the operating efficiency of the refrigeration cycle and guiding the actual liquid hydrogen production.
基金supported by the 2024 Research Fund of University of Ulsan.
文摘In recent years,three-dimensional reconstruction technologies that employ multiple cameras have continued to evolve significantly,enabling remote collaboration among users in extended Reality(XR)environments.In addition,methods for deploying multiple cameras for motion capture of users(e.g.,performers)are widely used in computer graphics.As the need to minimize and optimize the number of cameras grows to reduce costs,various technologies and research approaches focused on Optimal Camera Placement(OCP)are continually being proposed.However,as most existing studies assume homogeneous camera setups,there is a growing demand for studies on heterogeneous camera setups.For instance,technical demands keep emerging in scenarios with minimal camera configurations,especially regarding cost factors,the physical placement of cameras given the spatial structure,and image capture strategies for heterogeneous cameras,such as high-resolution RGB cameras and depth cameras.In this study,we propose a pre-visualization and simulation method for the optimal placement of heterogeneous cameras in XR environments,accounting for both the specifications of heterogeneous cameras(e.g.,field of view)and the physical configuration(e.g.,wall configuration)in real-world spaces.The proposed method performs a visibility analysis of cameras by considering each camera’s field-of-view volume,resolution,and unique characteristics,along with physicalspace constraints.This approach enables the optimal position and rotation of each camera to be recommended,along with the minimum number of cameras required.In the results of our study conducted in heterogeneous camera combinations,the proposed method achieved 81.7%~82.7%coverage of the target visual information using only 2~3 cameras.In contrast,single(or homogeneous)-typed cameras were required to use 11 cameras for 81.6%coverage.Accordingly,we found that camera deployment resources can be reduced with the proposed approaches.
基金supported by the Sinopec Technology Research and Development Project(No.30000000-22-ZC0607-0235,No.33550000-22-ZC0607-0009)the National Natural Science Foundation of China(No.52334002).
文摘Natural gas hydrate widely exists in the South China Sea as clean energy.A three-phase transition layer widely exists in low permeability Class I hydrates in the Shenhu offshore area.Therefore,taking into account the low-permeability characteristics with an average permeability of 5.5 mD and moderate heterogeneity,a 3-D geological model of heterogeneous Class I hydrate reservoirs with three-phase transition layers is established by Kriging interpolation and stochastic modeling method,and a numerical simulation model is used to describe the depressurization production performance of the reservoir.With the development of depressurization,a specific range of complete decomposition zones appear both in the hydrate and transition layers.The entire decomposition zone of the whole reservoir tends to outward and upward diffusion.There is apparent methane escape in the three-phase transition layer.Due to the improvement of local permeability caused by the phase transition of hydrate dissociation,some methane accumulation occurs at the bottom of the hydrate layer,forming a local methane enrichment zone.The methane migration trends in reservoirs are mainly characterized by movement toward production wells and hydrate layers under the influence of gravity.However,due to the permeability limitation of hydrate reservoirs,many fluids have not been effectively produced and remain in the reservoir.Therefore,to improve the effective pressure drop of the reservoir,the perforation method and pressure reduction method were optimized by analyzing the influencing factors based on the gas production rate.The comparative study demonstrates that perforating through the free gas layer combined with one-time depressurization can enhance the effective depressurization and improve production performance.The gas production rate from perforating through the free gas layer can be twice as high as that from perforating through the transition layer.This study can provide theoretical support for the utilization of marine energy.
基金National Key Research and Development Program of China(2022YFB4600902)Shandong Provincial Science Foundation for Outstanding Young Scholars(ZR2024YQ020)。
文摘Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing additive-induced defects,and alleviating residual stress and deformation,all of which are critical for enhancing the mechanical performance of the manufactured parts.Integrating interlayer friction stir processing(FSP)into WAAM significantly enhances the quality of deposited materials.However,numerical simulation research focusing on elucidating the associated thermomechanical coupling mechanisms remains insufficient.A comprehensive numerical model was developed to simulate the thermomechanical coupling behavior in friction stir-assisted WAAM.The influence of post-deposition FSP on the coupled thermomechanical response of the WAAM process was analyzed quantitatively.Moreover,the residual stress distribution and deformation behavior under both single-layer and multilayer deposition conditions were investigated.Thermal analysis of different deposition layers in WAAM and friction stir-assisted WAAM was conducted.Results show that subsequent layer deposition induces partial remelting of the previously solidified layer,whereas FSP does not cause such remelting.Furthermore,thermal stress and deformation analysis confirm that interlayer FSP effectively mitigates residual stresses and distortion in WAAM components,thereby improving their structural integrity and mechanical properties.
基金supported by the National Natural Science Foundation of China(52071039 and 52301156)National Natural Science Foundation of Jiangsu Province of China(BK20241873)Natural Science Foundation of Jiangsu Province(BK20232025 and BK20243005)are greatly acknowledged.
文摘Atomistic simulations were adopted to study the solute segregation effect on dislocation transmutation across the{1012}twin boundaries in magnesium.For pure magnesium,the dislocation-twin reaction resulted in the formation of sessile dislocations accompanied by the fast migration of the twin boundary,and no〈c+a〉dislocation occurred.With Al segregation,instead,two basal dislocations transmuted into one prismatic〈c+a〉dislocation in the twin.Twin migration was significantly impeded,and the resultant twin disconnections stayed localized and had a higher step character than in pure Mg.To reveal the mechanism of the effect of solute segregation,the Peierls barriers of twin disconnections were calculated,and the dynamic evolutions of twin disconnection dipoles were simulated.The results suggested that Al segregation softened the Peierls barrier of twin disconnections but imposed a high pinning force on twin disconnections,thus attenuating their mobility.Moreover,given the same Al segregation,the twin disconnection dipole with a higher step showed greater stability,which explained the presence of localized twin disconnections with a higher step in the cases with Al segregation than in pure magnesium.The solute segregation induced low mobility of twin disconnections contributed to the occurrence of〈c+a〉dislocations.
基金supported by the Advanced Materials-National Science and Technology Major Project(Grant No.2025ZD0618401)the National Natural Science Foundation of China(Grant No.12504285)+1 种基金the Natural Science Foundation of Jiangsu Province(Grant No.BK20250472)NFSG grant from BITS-Pilani,Dubai campus。
文摘The rapid advancement of machine learning based tight-binding Hamiltonian(MLTB)methods has opened new avenues for efficient and accurate electronic structure simulations,particularly in large-scale systems and long-time scenarios.This review begins with a concise overview of traditional tight-binding(TB)models,including both(semi-)empirical and first-principles approaches,establishing the foundation for understanding MLTB developments.We then present a systematic classification of existing MLTB methodologies,grouped into two major categories:direct prediction of TB Hamiltonian elements and inference of empirical parameters.A comparative analysis with other ML-based electronic structure models is also provided,highlighting the advancement of MLTB approaches.Finally,we explore the emerging MLTB application ecosystem,highlighting how the integration of MLTB models with a diverse suite of post-processing tools from linear-scaling solvers to quantum transport frameworks and molecular dynamics interfaces is essential for tackling complex scientific problems across different domains.The continued advancement of this integrated paradigm promises to accelerate materials discovery and open new frontiers in the predictive simulation of complex quantum phenomena.
基金financially supported by the National Natural Science Foundation of China(Nos.52173020 and 52573023)。
文摘Vitrimers belong to a class of polymeric materials capable of bond exchange reactions,showing great promise for environmental protection and sustainable development.However,studies on the coupling mechanism between the bond exchange kinetics and segmental dynamics near the glass transition temperature(T_(g))remain scarce.Herein,we employed molecular dynamics simulations to investigate the dynamic heterogeneity of the segment motion and bond exchange in vitrimers.The simulation results revealed that the bond exchange energy barrier exerts a much stronger influence on the bond exchange kinetics than on the segmental dynamics.At lower temperatures,slower segmental relaxation further constraind the bond exchange rate.Additionally,increasing the bond exchange energy barrier markedly enhanced the dynamic heterogeneity of segment motion.A close correlation was observed between heterogeneity and bond exchange.This study elucidated the coupling mechanism between bond exchange and segmental dynamics at the molecular scale,thereby providing a theoretical basis for designing vitrimer materials with tunable dynamic properties.
