To address the challenges in studying the pore formation and evolution processes,and unclear preservation mechanisms of deep to ultra-deep carbonate rocks,a high-temperature and high-pressure visualization simulation ...To address the challenges in studying the pore formation and evolution processes,and unclear preservation mechanisms of deep to ultra-deep carbonate rocks,a high-temperature and high-pressure visualization simulation experimental device was developed for ultra-deep carbonate reservoirs.Carbonate rock samples from the Sichuan Basin and Tarim Basin were used to simulate the dissolution-precipitation process of deep to ultra-deep carbonate reservoirs in an analogous geological setting.This unit comprises four core modules:an ultra-high temperature,high pressure triaxial stress core holder module(temperature higher than 300°C,pressure higher than 150 MPa),a multi-stage continuous flow module with temperature-pressure regulation,an ultra-high temperature-pressure sapphire window cell and an in-situ high-temperature-pressure fluid property measurement module and real-time ultra-high temperature-pressure permeability detection module.The new experimental device was used for simulation experiment,the geological insights were obtained in three aspects.First,the pore-throat structure of carbonate is controlled by lithology and initial pore-throat structure,and fluid type,concentration and dissolution duration determine the degree of dissolution.The dissolution process exhibits two evolution patterns.The dissolution scale is positively correlated to the temperature and pressure,and the pore-forming peak period aligns well with the hydrocarbon generation peak period.Second,the dissolution potential of dolomite in an open flow system is greater than that of limestone,and secondary dissolved pores formed continuously are controlled by the type and concentration of acidic fluids and the initial physical properties.These pores predominantly distribute along pre-existing pore/fracture zones.Third,in a nearly closed diagenetic system,after the chemical reaction between acidic fluids and carbonate rock reaches saturation and dynamic equilibrium,the pore structure no longer changes,keeping pre-existing pores well-preserved.These findings have important guiding significance for the evaluation of pore-throat structure and development potential of deep to ultra-deep carbonate reservoirs,and the prediction of main controlling factors and distribution of high-quality carbonate reservoirs.展开更多
Thiadiamondoids(TDs)have recently attracted increasing attention as molecular proxies for thermochemical sulfate reduction(TSR)reactions in reservoirs.However,their formation mechanisms,as well as the generation and e...Thiadiamondoids(TDs)have recently attracted increasing attention as molecular proxies for thermochemical sulfate reduction(TSR)reactions in reservoirs.However,their formation mechanisms,as well as the generation and evolution processes,remain poorly understood.In this study,simulation experiments with a duration of 160 h were conducted on the model compound 1,3-dimethyladamantane(1,3-DMA)using the CaSO_(4),MgSO_(4),and elemental S systems,with measurements at the 10th,20th,40th,80th and 160th hours during the simulation process being presented.The results indicate that at the end of simulation,the MgSO_(4) system exhibited the lowest residual amounts of 1,3-DMA,suggesting the highest degree of TSR.Four types of non-hydrocarbon compounds with adamantane structures were detected in the liquid products in the three experiment systems:adamantanones,adamantanols,adamantanethiols(ATs),and thiaadamantanes(TAs).Among these,adamantanones exhibited the highest concentrations in the three simulation systems.In addition,TAs were dominated by C_(3)-TAs in the CaSO_(4) and MgSO_(4) systems and by C_(2)-TAs in the elemental S system.The simulation experiments revealed a strong correlation between the concentrations of TAs and adamantanones,suggesting that adamantanones might be the intermediates for TAs.Combined with the synthesis mechanism of TAs from thiaadamamantane-4,8-dione,TDs might have two different genetic mechanisms:(a)low temperature cationic carbon ion rearrangement from diagenesis to early catagenesis stage,and(b)a free sulfur radical mechanism in high-temperature TSR process during middle-late catagenesis.TAs exhibited different generation and evolution processes across different experiment systems.Notably,the MgSO_(4) system revealed that TAs undergo generation,accumulation,and destruction process,corresponding to Easy%Ro values of 0.89%-0.98%,0.98%-1.21%,and>1.21%,respectively.Among these three simulation systems,dibenzothiophenes(DBTs)concentrations consistently trended upwards,indicating TAs have lower thermal stability than DBTs.展开更多
In this study,the hydraulic behavior and sand transport efficiency of the siphon automatic sand discharge device were studied by software simulation tests.By simulating the actual situation,this study analyzed how fac...In this study,the hydraulic behavior and sand transport efficiency of the siphon automatic sand discharge device were studied by software simulation tests.By simulating the actual situation,this study analyzed how factors such as the difference in water level,sediment concentration,and pipeline layout affected the sediment discharge effect.The results show that the sediment discharge device can effectively discharge sediment under diverse operating conditions and show adaptability to different environmental conditions,which indicates that it is suitable for various types of reservoir environments.展开更多
In the ultra-deep strata of the Tarim Basin,the vertical growth process of strike-slip faults remains unclear,and the vertical distribution of fractured-cavity carbonate reservoirs is complex.This paper investigates t...In the ultra-deep strata of the Tarim Basin,the vertical growth process of strike-slip faults remains unclear,and the vertical distribution of fractured-cavity carbonate reservoirs is complex.This paper investigates the vertical growth process of strike-slip faults through field outcrop observations in the Keping area,interpretation of seismic data from the Fuman Oilfield,Tarim Basim,NW China,and structural physical simulation experiments.The results are obtained mainly in four aspects.First,field outcrops and ultra-deep seismic profiles indicate a three-layer structure within the strike-slip fault,consisting of fault core,fracture zone and primary rock.The fault core can be classified into three parts vertically:fracture-cavity unit,fault clay and breccia zone.The distribution of fracture-cavity units demonstrates a distinct pattern of vertical stratification,owing to the structural characteristics and growth process of the slip-strike fault.Second,the ultra-deep seismic profiles show multiple fracture-cavity units in the strike-slip fault zone.These units can be classified into four types:top fractured,middle connected,deep terminated,and intra-layer fractured.Third,structural physical simulation experiments and ultra-deep seismic data interpretation reveal that the strike-slip faults have evolved vertically in three stages:segmental rupture,vertical growth,and connection and extension.The particle image velocimetry detection demonstrates that the initial fracture of the fault zone occurred at the top or bottom and then evolved into cavities gradually along with the fault growth,accompanied by the emergence of new fractures in the middle part of the strata,which subsequently connected with the deep and shallow cavities to form a complete fault zone.Fourth,the ultra-deep carbonate strata primarily develop three types of fractured-cavity reservoirs:flower-shaped fracture,large and deep fault and staggered overlap.The first two types are larger in size with better reservoir conditions,suggesting a significant exploration potential.展开更多
Soil cracking is an important process influencing water and solutes transport in the Yuanmou Dry-hot Valley region of Southwest China. Studying the morphological development of soil cracks helps to further reveal the ...Soil cracking is an important process influencing water and solutes transport in the Yuanmou Dry-hot Valley region of Southwest China. Studying the morphological development of soil cracks helps to further reveal the close relationship between the soil cracking process and water movement in such semi-arid regions. Here we report regular changes on surface morphology of soil cracks with decreasing water in four different soils (Typ-Ustic Ferrisols,Ver-Ustic Ferrisols,Tru-Ustic Vertisols and Typ-Ustic Vertisols) through simulation experiments. Our results indicate the following: 1) Different soils ultimately have different development degrees of soil cracks,according to their various values of crack area density. Soil cracks in Typ-Ustic Ferrisols can only develop to the feeble degree,while those in the other three soils are capable of developing into the intensive degree,and even into the extremely intensive degree. 2) Soil crack complexity,as expressed by the value of the area-weighted mean of crack fractal dimension (AWMFRAC),is found to continuously decrease as a whole through the whole cracking process in all the studied soils. 3) Soil crack connectivity shows a uniform trend in the studied soils,that is to say,connectivity gradually increases with soil crack development.展开更多
Thermochemical sulfate reduction (TSR) in geological deposits can account for the accumulation of H2S in deep sour gas reservoirs. In this paper, thermal simulation experiments on the reaction of CH4-CaSO4 were carri...Thermochemical sulfate reduction (TSR) in geological deposits can account for the accumulation of H2S in deep sour gas reservoirs. In this paper, thermal simulation experiments on the reaction of CH4-CaSO4 were carried out using an autoclave at high temperatures and high pressures. The products were characterized with analytical methods including carbon isotope analysis. It is found that the reaction can proceed to produce H2S, H2O and CaCO3 as the main products. Based on the experimental results, the carbon kinetic isotope fractionation was investigated, and the value of Ki (kinetic isotope effect) was calculated. The results obtained in this paper can provide useful information to explain the occurrence of H2S in deep carbonate gas reservoirs.展开更多
Presented the fiber Bragg grating （FBG） sensors for rock strain monitoring in the 1.2 m long plane stress model of the simulation experiment. In the past, for the lack of appropriate technique to measure the deforma...Presented the fiber Bragg grating （FBG） sensors for rock strain monitoring in the 1.2 m long plane stress model of the simulation experiment. In the past, for the lack of appropriate technique to measure the deformation of rock structures, the measurement of deflection was restricted to just a few discrete points along rock, and the measuring points were limited to the location installed with displacement transducers. We developed a method to monitor the deformation of rock structures using fiber optical Bragg grating strain sensors. The sensors were embedded in rock layers of simulation experiment before the materials were put in. These sensors were then used to monitor the experienced strain with different face advancing distance. The test results indicate that, if properly installed, FBG sensors can survive under severe conditions associated with embedment process and yield accurate measurements of strains response. At the same time, we make comparisons of the data obtained by FBG sensors with those by centesimal gauge. The interest in FBG sensors was motivated by the potential advantages that they can offer more than existing sensing technologies.展开更多
Yellow River water transfer for Tianjin is important in solving the water shortage in Tianjin, which facilitate economic development and social progress for many years. Fresh water drawn from Yellow River（ i. e., Yin...Yellow River water transfer for Tianjin is important in solving the water shortage in Tianjin, which facilitate economic development and social progress for many years. Fresh water drawn from Yellow River（ i. e., Yin-Huang water） becomes saltier and saltier when being stored in the Bei-Da-Gang reservoir. We qualitatively analyze the water salinization mechanism based on mass transfer theory. The main factors are salinity transfer of saline soil, evaporation concentrating, and the agitation of wind. A simulative experimental pond and an evaporation pond were built beside the Bei-Da-Gang reservoir to quantitatively investigate the water salinization based on water and solute balance in the simulative pond. 80% of increased [Cl^-] is due to the salinity transfer of the saline soil and the other 20% is due to evaporation concentrating, so the former is the most important factor. We found that the salinization of Yin-Huang water can be described with a zero-dimension linear model.展开更多
In order to analyze the factors influencing sandstone mechanical compaction and its physical property evolution during compaction processes, simulation exper- iments on sandstone mechanical compaction were carried out...In order to analyze the factors influencing sandstone mechanical compaction and its physical property evolution during compaction processes, simulation exper- iments on sandstone mechanical compaction were carried out with a self-designed diagenetic simulation system. The experimental materials were modem sediments from dif- ferent sources, and the experiments were conducted under high temperature and high pressure. Results of the exper- iments show a binary function relation between primary porosity and mean size as well as sorting. With increasing overburden pressure during mechanical compaction, the evolution of porosity and permeability can be divided into rapid compaction at an early stage and slow compaction at a late stage, and the dividing pressure value of the two stages is about 12 MPa and the corresponding depth is about 600 m. In the slow compaction stage, there is a good exponential relationship between porosity and overburden pressure, while a good power function relationship exists between permeability and overburden pressure. There is also a good exponential relationship between porosity and permeability. The influence of particle size on sandstone mechanical compaction is mainly reflected in the slowcompaction stage, and the influence of sorting is mainly reflected in the rapid compaction stage. Abnormally high pressure effectively inhibits sandstone mechanical com- paction, and its control on sandstone mechanical com- paction is stronger than that of particle size and sorting. The influence of burial time on sandstone mechanical compaction is mainly in the slow compaction stage, and the porosity reduction caused by compaction is mainly con- trolled by average particle size.展开更多
An ensemble-based method for the observation system simulation experiment(OSSE)is employed to design optimal observation stations and assess the present observation stations in the northeastern South China Sea(SCS).We...An ensemble-based method for the observation system simulation experiment(OSSE)is employed to design optimal observation stations and assess the present observation stations in the northeastern South China Sea(SCS).We employed the 20-year(1992-2012)sea surface height(SSH)data to design an array to monitor the intraseasonal to interannual variability.The results show that the most key region was found located at the northwest of Luzon Island(LI)where the energetic Luzon cyclonic gyre(LCG)occurs;other key regions include the edge of the LCG,the northwest of the Luzon Strait(LS),and the southwest of Taiwan,China.By contrast,we found that the present observation stations might oversample at the northwest of the LS and undersample at the northwest of LI.In addition,the optimal stations perform better in a larger area than the present stations.In vertical direction,the key layer is located within the upper 200-m depth,of which the surface and subsurface layers are most valuable to the observing system.展开更多
According to a research on the 30kVA simulation experimental platform of hydraulic wind tur- bine, its basic structure, composition and operation principle are expounded in this paper. An in- verter motor is used to s...According to a research on the 30kVA simulation experimental platform of hydraulic wind tur- bine, its basic structure, composition and operation principle are expounded in this paper. An in- verter motor is used to simulate the wind turbine, while a similarity calculation method is applied be- tween the small and large wind turbine. A fixed displacement pump-variable motor closed loop is used as the main transmission system, and a self-excited synchronous generator generates electricity through the grid connection. The experiment and simulation study on the speed and power control of the hydraulic wind turbine is conducted, based on the experimental platform, thus correctness and progressiveness of the experiment platform is further verified. The experimental platform study lays a foundation for further research on the characteristics of hydraulic wind turhln~展开更多
To analyze the overlying strata movement law of recovering room mining standing pillars with solid backfilling.Physical simulation experiments with sponge and wood as the backfilling simulation material were tested.Th...To analyze the overlying strata movement law of recovering room mining standing pillars with solid backfilling.Physical simulation experiments with sponge and wood as the backfilling simulation material were tested.The results show that:(i) The covering-rock mechanics of the overly strata comes from "two-arch structures + hinged girder + bend beam" to "backfilling material + hinged girder + bent beam" by increasing the fill ratio from 0%to 85%,the beginning of overlying strata movement appears later and the total duration of subsidence velocity increased from zero to the highest value increases.The trend of "single polarization" of the subsidence velocity curves becomes noticeable and the velocity variation trend becomes stable,(ii) The equiponderate aeolian sand was added to improve the anti-pressure ability of the loess,and the corresponding ground processing & transportation system was designed.展开更多
The distributions of local velocity and local phase holdup along the radial direction of pipes are complicated because of gravity differentiation,and the distribution of fluid velocity fi eld changes along the gravity...The distributions of local velocity and local phase holdup along the radial direction of pipes are complicated because of gravity differentiation,and the distribution of fluid velocity fi eld changes along the gravity direction in horizontal wells.Therefore,measuring the mixture flow and water holdup is difficult,resulting in poor interpretation accuracy of the production logging output profile.In this paper,oil–water two-phase flow dynamic simulation logging experiments in horizontal oil–water two-phase fl ow simulation wells were conducted using the Multiple Array Production Suite,which comprises a capacitance array tool(CAT)and a spinner array tool(SAT),and then the response characteristics of SAT and CAT in diff erent fl ow rates and water cut production conditions were studied.According to the response characteristics of CAT in diff erent water holdup ranges,interpolation imaging along the wellbore section determines the water holdup distribution,and then,the oil–water two-phase velocity fi eld in the fl ow section was reconstructed on the basis of the fl ow section water holdup distribution and the logging value of SAT and combined with the rheological equation of viscous fl uid,and the calculation method of the oil–water partial phase fl ow rate in the fl ow section was proposed.This new approach was applied in the experiment data calculations,and the results are basically consistent with the experimental data.The total fl ow rate and water holdup from the calculation are in agreement with the set values in the experiment,suggesting that the method has high accuracy.展开更多
Based on the existing Land Surface Physical Process Models(Deardorff, Dickinson, LIU, Noilhan, Seller, ZHAO), a Comprehensive Land Surface Physical Process Model (CLSPPM) is developed by considering the different phys...Based on the existing Land Surface Physical Process Models(Deardorff, Dickinson, LIU, Noilhan, Seller, ZHAO), a Comprehensive Land Surface Physical Process Model (CLSPPM) is developed by considering the different physical processes of the earth's surface-vegetation-atmosphere system more completely. Compared with SiB and BATS, which are famous for their detailed parameterizations of physical variables, this simplified model is more convenient and saves much more computation time. Though simple, the feas...展开更多
Two measurement techniques are investigated to characterize photodetector linearity. A model for the two-tone and three-tone photodetector systems is developed to thoroughly investigate the influences of setup compone...Two measurement techniques are investigated to characterize photodetector linearity. A model for the two-tone and three-tone photodetector systems is developed to thoroughly investigate the influences of setup components on the measurement results. We demonstrate that small bias shifts from the quadrature point of the modulator will induce deviation into measurement results of the two-tone system, and the simulation results correspond well to experimental and calculation results.展开更多
Background Most existing chemical experiment teaching systems lack solid immersive experiences,making it difficult to engage students.To address these challenges,we propose a chemical simulation teaching system based ...Background Most existing chemical experiment teaching systems lack solid immersive experiences,making it difficult to engage students.To address these challenges,we propose a chemical simulation teaching system based on virtual reality and gesture interaction.Methods The parameters of the models were obtained through actual investigation,whereby Blender and 3DS MAX were used to model and import these parameters into a physics engine.By establishing an interface for the physics engine,gesture interaction hardware,and virtual reality(VR)helmet,a highly realistic chemical experiment environment was created.Using code script logic,particle systems,as well as other systems,chemical phenomena were simulated.Furthermore,we created an online teaching platform using streaming media and databases to address the problems of distance teaching.Results The proposed system was evaluated against two mainstream products in the market.In the experiments,the proposed system outperformed the other products in terms of fidelity and practicality.Conclusions The proposed system which offers realistic simulations and practicability,can help improve the high school chemistry experimental education.展开更多
Tofigure out the process and controlling factors of gas reservoir formation in deep-waters,based on an analysis of geological features,source of natural gas and process of reservoir formation in the Liwan 3-1 gasfield...Tofigure out the process and controlling factors of gas reservoir formation in deep-waters,based on an analysis of geological features,source of natural gas and process of reservoir formation in the Liwan 3-1 gasfield,physical simulation experiment of the gas reservoir formation process has been performed,consequently,pattern and features of gas reservoir formation in the Baiyun sag has been found out.The results of the experiment show that:①the formation of the Liwan 3-1 faulted anticline gasfield is closely related to the longstanding active large faults,where natural gas is composed of a high proportion of hydrocarbons,a small amount of non-hydrocarbons,and the wet gas generated during highly mature stage shows obvious vertical migration signs;②liquid hydrocarbons associated with natural gas there are derived from source rock of the Enping&Zhuhai Formation,whereas natural gas comes mainly from source rock of the Enping Formation,and source rock of the Wenchang Formation made a little contribution during the early Eocene period as well;③although there was gas migration and accumulation,yet most of the natural gas mainly scattered and dispersed due to the stronger activity of faults in the early period;later as fault activity gradually weakened,gas started to accumulate into reservoirs in the Baiyun sag;④there is stronger vertical migration of oil and gas than lateral migration,and the places where fault links effective source rocks with reservoirs are most likely for gas accumulation;⑤effective temporal-spatial coupling of source-fault-reservoir in late stage is the key to gas reservoir formation in the Baiyun sag;⑥the nearer the distance from a trap to a large-scale fault and hydrocarbon source kitchen,the more likely gas may accumulate in the trap in late stage,therefore gas accumulation efficiency is much lower for the traps which are far away from large-scale faults and hydrocarbon source kitchens.展开更多
Background Machine learning-based beer bottle-defect detection is a complex technology that runs automatically;however,it consumes considerable memory,is expensive,and poses a certain danger when training novice opera...Background Machine learning-based beer bottle-defect detection is a complex technology that runs automatically;however,it consumes considerable memory,is expensive,and poses a certain danger when training novice operators.Moreover,some topics are difficult to learn from experimental lectures,such as digital image processing and computer vision.However,virtual simulation experiments have been widely used to good effect within education.A virtual simulation of the design and manufacture of a beer bottle-defect detection system will not only help the students to increase their image-processing knowledge,but also improve their ability to solve complex engineering problems and design complex systems.Methods The hardware models for the experiment(camera,light source,conveyor belt,power supply,manipulator,and computer)were built using the 3DS MAX modeling and animation software.The Unreal Engine 4(UE4)game engine was utilized to build a virtual design room,design the interactive operations,and simulate the system operation.Results The results showed that the virtual-simulation system received much better experimental feedback,which facilitated the design and manufacture of a beer bottle-defect detection system.The specialized functions of the functional modules in the detection system,including a basic experimental operation menu,power switch,image shooting,image processing,and manipulator grasping,allowed students(or virtual designers)to easily build a detection system by retrieving basic models from the model library,and creating the beer-bottle transportation,image shooting,image processing,defect detection,and defective-product removal.The virtual simulation experiment was completed with image processing as the main body.Conclusions By mainly focusing on bottle mouth defect detection,the detection system dedicates more attention to the user and the task.With more detailed tasks available,the virtual system will eventually yield much better results as a training tool for image processing education.In addition,a novel visual perception-thinking pedagogical framework enables better comprehension than the traditional lecture-tutorial style.展开更多
According to the service environment of subway structure,experiment is carried out to simulate influence of different loading levels to reinforcement corrosion of R.C element affected by stray current and chlorine sal...According to the service environment of subway structure,experiment is carried out to simulate influence of different loading levels to reinforcement corrosion of R.C element affected by stray current and chlorine salt solution. The current density of the corrosion is measured with the linear polarization resistance method,together with the qualitative analysis and quantitative calculation. Experiment shows that rebar corrosion current density increase accordingly with the increase of loading level. The quantitative relations and the time of rust corrosion of reinforcement are obtained.展开更多
Surface sediment samples taken from the East China Sea off the Changjiang estuary are used as raw materials for phosphorus releasing experiment. It is found that after being thoroughly mixed with seawater for about 10...Surface sediment samples taken from the East China Sea off the Changjiang estuary are used as raw materials for phosphorus releasing experiment. It is found that after being thoroughly mixed with seawater for about 10 minutes, phosphorus released from the sediments reaches its maximum value. Adsorption kinetics can be fitted with both Elovich equation and two-constant rate equation. The releasing amount is closely related to the composition of the sediments. Phosphorus release from silty and muddy sediment is higher than from that dominated by sandy composition. For the desorption reaction, iron-phosphorus (Fe-P) is the most active one, with a releasing ratio higher than other phosphorus forms, followed by absorbed-phosphorus (Ad-P) and organic bound phosphorus (OP). All of them can be referred to as bio-available phosphorus. The results demonstrate that phosphorus in sediments can be released into seawater under suitable hydrodynamic conditions, and have a great impact on the nutrition state and primary productivity of marine biosphere.展开更多
基金Supported by the Joint Fund for Enterprise Innovation and Development of the National Natural Science Foundation of China(U23B20154)General Program of the National Natural Science Foundation of China(42372169)。
文摘To address the challenges in studying the pore formation and evolution processes,and unclear preservation mechanisms of deep to ultra-deep carbonate rocks,a high-temperature and high-pressure visualization simulation experimental device was developed for ultra-deep carbonate reservoirs.Carbonate rock samples from the Sichuan Basin and Tarim Basin were used to simulate the dissolution-precipitation process of deep to ultra-deep carbonate reservoirs in an analogous geological setting.This unit comprises four core modules:an ultra-high temperature,high pressure triaxial stress core holder module(temperature higher than 300°C,pressure higher than 150 MPa),a multi-stage continuous flow module with temperature-pressure regulation,an ultra-high temperature-pressure sapphire window cell and an in-situ high-temperature-pressure fluid property measurement module and real-time ultra-high temperature-pressure permeability detection module.The new experimental device was used for simulation experiment,the geological insights were obtained in three aspects.First,the pore-throat structure of carbonate is controlled by lithology and initial pore-throat structure,and fluid type,concentration and dissolution duration determine the degree of dissolution.The dissolution process exhibits two evolution patterns.The dissolution scale is positively correlated to the temperature and pressure,and the pore-forming peak period aligns well with the hydrocarbon generation peak period.Second,the dissolution potential of dolomite in an open flow system is greater than that of limestone,and secondary dissolved pores formed continuously are controlled by the type and concentration of acidic fluids and the initial physical properties.These pores predominantly distribute along pre-existing pore/fracture zones.Third,in a nearly closed diagenetic system,after the chemical reaction between acidic fluids and carbonate rock reaches saturation and dynamic equilibrium,the pore structure no longer changes,keeping pre-existing pores well-preserved.These findings have important guiding significance for the evaluation of pore-throat structure and development potential of deep to ultra-deep carbonate reservoirs,and the prediction of main controlling factors and distribution of high-quality carbonate reservoirs.
基金funded by the Natural Science Foundation of China(Grants Nos.42272167,U24B6001,and 41772153)Science&Technology Project of Sinopec(Grant Nos.P23167 and P24173).
文摘Thiadiamondoids(TDs)have recently attracted increasing attention as molecular proxies for thermochemical sulfate reduction(TSR)reactions in reservoirs.However,their formation mechanisms,as well as the generation and evolution processes,remain poorly understood.In this study,simulation experiments with a duration of 160 h were conducted on the model compound 1,3-dimethyladamantane(1,3-DMA)using the CaSO_(4),MgSO_(4),and elemental S systems,with measurements at the 10th,20th,40th,80th and 160th hours during the simulation process being presented.The results indicate that at the end of simulation,the MgSO_(4) system exhibited the lowest residual amounts of 1,3-DMA,suggesting the highest degree of TSR.Four types of non-hydrocarbon compounds with adamantane structures were detected in the liquid products in the three experiment systems:adamantanones,adamantanols,adamantanethiols(ATs),and thiaadamantanes(TAs).Among these,adamantanones exhibited the highest concentrations in the three simulation systems.In addition,TAs were dominated by C_(3)-TAs in the CaSO_(4) and MgSO_(4) systems and by C_(2)-TAs in the elemental S system.The simulation experiments revealed a strong correlation between the concentrations of TAs and adamantanones,suggesting that adamantanones might be the intermediates for TAs.Combined with the synthesis mechanism of TAs from thiaadamamantane-4,8-dione,TDs might have two different genetic mechanisms:(a)low temperature cationic carbon ion rearrangement from diagenesis to early catagenesis stage,and(b)a free sulfur radical mechanism in high-temperature TSR process during middle-late catagenesis.TAs exhibited different generation and evolution processes across different experiment systems.Notably,the MgSO_(4) system revealed that TAs undergo generation,accumulation,and destruction process,corresponding to Easy%Ro values of 0.89%-0.98%,0.98%-1.21%,and>1.21%,respectively.Among these three simulation systems,dibenzothiophenes(DBTs)concentrations consistently trended upwards,indicating TAs have lower thermal stability than DBTs.
基金Supported by the National Undergraduate Innovation Training Program(Project No.202211437036).
文摘In this study,the hydraulic behavior and sand transport efficiency of the siphon automatic sand discharge device were studied by software simulation tests.By simulating the actual situation,this study analyzed how factors such as the difference in water level,sediment concentration,and pipeline layout affected the sediment discharge effect.The results show that the sediment discharge device can effectively discharge sediment under diverse operating conditions and show adaptability to different environmental conditions,which indicates that it is suitable for various types of reservoir environments.
基金Supported by the National Natural Science Foundation of China(42362026)Key R&D Project of Xinjiang Uygur Autonomous Region(2024B01015).
文摘In the ultra-deep strata of the Tarim Basin,the vertical growth process of strike-slip faults remains unclear,and the vertical distribution of fractured-cavity carbonate reservoirs is complex.This paper investigates the vertical growth process of strike-slip faults through field outcrop observations in the Keping area,interpretation of seismic data from the Fuman Oilfield,Tarim Basim,NW China,and structural physical simulation experiments.The results are obtained mainly in four aspects.First,field outcrops and ultra-deep seismic profiles indicate a three-layer structure within the strike-slip fault,consisting of fault core,fracture zone and primary rock.The fault core can be classified into three parts vertically:fracture-cavity unit,fault clay and breccia zone.The distribution of fracture-cavity units demonstrates a distinct pattern of vertical stratification,owing to the structural characteristics and growth process of the slip-strike fault.Second,the ultra-deep seismic profiles show multiple fracture-cavity units in the strike-slip fault zone.These units can be classified into four types:top fractured,middle connected,deep terminated,and intra-layer fractured.Third,structural physical simulation experiments and ultra-deep seismic data interpretation reveal that the strike-slip faults have evolved vertically in three stages:segmental rupture,vertical growth,and connection and extension.The particle image velocimetry detection demonstrates that the initial fracture of the fault zone occurred at the top or bottom and then evolved into cavities gradually along with the fault growth,accompanied by the emergence of new fractures in the middle part of the strata,which subsequently connected with the deep and shallow cavities to form a complete fault zone.Fourth,the ultra-deep carbonate strata primarily develop three types of fractured-cavity reservoirs:flower-shaped fracture,large and deep fault and staggered overlap.The first two types are larger in size with better reservoir conditions,suggesting a significant exploration potential.
基金Under the auspices of National Natural Science Foundation of China (No. 40901009)National Key Technologies Research and Development Program in the Eleventh Five-Year Plan of China (No. 2008BAD98B02, 2006BAC01A11)+1 种基金the Western Light Program of Talents Cultivating of Chinese Academy of Sciences (2008)the Foundation of Key Laboratory of Mountain Hazards and Surface Process, Chinese Academy of Sciences
文摘Soil cracking is an important process influencing water and solutes transport in the Yuanmou Dry-hot Valley region of Southwest China. Studying the morphological development of soil cracks helps to further reveal the close relationship between the soil cracking process and water movement in such semi-arid regions. Here we report regular changes on surface morphology of soil cracks with decreasing water in four different soils (Typ-Ustic Ferrisols,Ver-Ustic Ferrisols,Tru-Ustic Vertisols and Typ-Ustic Vertisols) through simulation experiments. Our results indicate the following: 1) Different soils ultimately have different development degrees of soil cracks,according to their various values of crack area density. Soil cracks in Typ-Ustic Ferrisols can only develop to the feeble degree,while those in the other three soils are capable of developing into the intensive degree,and even into the extremely intensive degree. 2) Soil crack complexity,as expressed by the value of the area-weighted mean of crack fractal dimension (AWMFRAC),is found to continuously decrease as a whole through the whole cracking process in all the studied soils. 3) Soil crack connectivity shows a uniform trend in the studied soils,that is to say,connectivity gradually increases with soil crack development.
文摘Thermochemical sulfate reduction (TSR) in geological deposits can account for the accumulation of H2S in deep sour gas reservoirs. In this paper, thermal simulation experiments on the reaction of CH4-CaSO4 were carried out using an autoclave at high temperatures and high pressures. The products were characterized with analytical methods including carbon isotope analysis. It is found that the reaction can proceed to produce H2S, H2O and CaCO3 as the main products. Based on the experimental results, the carbon kinetic isotope fractionation was investigated, and the value of Ki (kinetic isotope effect) was calculated. The results obtained in this paper can provide useful information to explain the occurrence of H2S in deep carbonate gas reservoirs.
基金National Natural Science Foundation of PRC(50374055)Shaanxi Key Lab of Ground Control(02JS43)
文摘Presented the fiber Bragg grating （FBG） sensors for rock strain monitoring in the 1.2 m long plane stress model of the simulation experiment. In the past, for the lack of appropriate technique to measure the deformation of rock structures, the measurement of deflection was restricted to just a few discrete points along rock, and the measuring points were limited to the location installed with displacement transducers. We developed a method to monitor the deformation of rock structures using fiber optical Bragg grating strain sensors. The sensors were embedded in rock layers of simulation experiment before the materials were put in. These sensors were then used to monitor the experienced strain with different face advancing distance. The test results indicate that, if properly installed, FBG sensors can survive under severe conditions associated with embedment process and yield accurate measurements of strains response. At the same time, we make comparisons of the data obtained by FBG sensors with those by centesimal gauge. The interest in FBG sensors was motivated by the potential advantages that they can offer more than existing sensing technologies.
基金The Science and Technology Development in Tianjin(No.033112211)
文摘Yellow River water transfer for Tianjin is important in solving the water shortage in Tianjin, which facilitate economic development and social progress for many years. Fresh water drawn from Yellow River（ i. e., Yin-Huang water） becomes saltier and saltier when being stored in the Bei-Da-Gang reservoir. We qualitatively analyze the water salinization mechanism based on mass transfer theory. The main factors are salinity transfer of saline soil, evaporation concentrating, and the agitation of wind. A simulative experimental pond and an evaporation pond were built beside the Bei-Da-Gang reservoir to quantitatively investigate the water salinization based on water and solute balance in the simulative pond. 80% of increased [Cl^-] is due to the salinity transfer of the saline soil and the other 20% is due to evaporation concentrating, so the former is the most important factor. We found that the salinization of Yin-Huang water can be described with a zero-dimension linear model.
基金co-funded by the National Natural Science Foundation of China (Grant No.U1262203)the National Science and Technology Special Grant (Grant No.2011ZX05009003)+1 种基金the Fundamental Research Funds for the Central Universities (Grant No.14CX06013A)the Chinese Scholarship Council (No.201406450019)
文摘In order to analyze the factors influencing sandstone mechanical compaction and its physical property evolution during compaction processes, simulation exper- iments on sandstone mechanical compaction were carried out with a self-designed diagenetic simulation system. The experimental materials were modem sediments from dif- ferent sources, and the experiments were conducted under high temperature and high pressure. Results of the exper- iments show a binary function relation between primary porosity and mean size as well as sorting. With increasing overburden pressure during mechanical compaction, the evolution of porosity and permeability can be divided into rapid compaction at an early stage and slow compaction at a late stage, and the dividing pressure value of the two stages is about 12 MPa and the corresponding depth is about 600 m. In the slow compaction stage, there is a good exponential relationship between porosity and overburden pressure, while a good power function relationship exists between permeability and overburden pressure. There is also a good exponential relationship between porosity and permeability. The influence of particle size on sandstone mechanical compaction is mainly reflected in the slowcompaction stage, and the influence of sorting is mainly reflected in the rapid compaction stage. Abnormally high pressure effectively inhibits sandstone mechanical com- paction, and its control on sandstone mechanical com- paction is stronger than that of particle size and sorting. The influence of burial time on sandstone mechanical compaction is mainly in the slow compaction stage, and the porosity reduction caused by compaction is mainly con- trolled by average particle size.
基金Supported by the National Key Research&Development Plan of China(Nos.2016YFC1401703,2016YFC1401702,2018YFC0309803)the National Natural Science Foundation of China(Nos.41506002,41676010,41476011,41676015,41606026)+1 种基金the Institution of South China Sea Ecology and Environmental Engineering,Chinese Academy of Sciences(No.ISEE2019ZR0)the Guangzhou Science and Technology Foundation(No.201804010133)。
文摘An ensemble-based method for the observation system simulation experiment(OSSE)is employed to design optimal observation stations and assess the present observation stations in the northeastern South China Sea(SCS).We employed the 20-year(1992-2012)sea surface height(SSH)data to design an array to monitor the intraseasonal to interannual variability.The results show that the most key region was found located at the northwest of Luzon Island(LI)where the energetic Luzon cyclonic gyre(LCG)occurs;other key regions include the edge of the LCG,the northwest of the Luzon Strait(LS),and the southwest of Taiwan,China.By contrast,we found that the present observation stations might oversample at the northwest of the LS and undersample at the northwest of LI.In addition,the optimal stations perform better in a larger area than the present stations.In vertical direction,the key layer is located within the upper 200-m depth,of which the surface and subsurface layers are most valuable to the observing system.
基金Supported by the National Key Basic Research Development Program of China(No.2014CB046405)the National Natural Science Foundation of China(No.51475406,51405423)the Hebei Youth Fund(No.QN20132017)
文摘According to a research on the 30kVA simulation experimental platform of hydraulic wind tur- bine, its basic structure, composition and operation principle are expounded in this paper. An in- verter motor is used to simulate the wind turbine, while a similarity calculation method is applied be- tween the small and large wind turbine. A fixed displacement pump-variable motor closed loop is used as the main transmission system, and a self-excited synchronous generator generates electricity through the grid connection. The experiment and simulation study on the speed and power control of the hydraulic wind turbine is conducted, based on the experimental platform, thus correctness and progressiveness of the experiment platform is further verified. The experimental platform study lays a foundation for further research on the characteristics of hydraulic wind turhln~
基金provided by the National Natural Science Foundation of China(No.51074165)the NationalKey Basic Research Program of China(No.2013CB227905)the Qing-Lan Project of China Scholarship Council
文摘To analyze the overlying strata movement law of recovering room mining standing pillars with solid backfilling.Physical simulation experiments with sponge and wood as the backfilling simulation material were tested.The results show that:(i) The covering-rock mechanics of the overly strata comes from "two-arch structures + hinged girder + bend beam" to "backfilling material + hinged girder + bent beam" by increasing the fill ratio from 0%to 85%,the beginning of overlying strata movement appears later and the total duration of subsidence velocity increased from zero to the highest value increases.The trend of "single polarization" of the subsidence velocity curves becomes noticeable and the velocity variation trend becomes stable,(ii) The equiponderate aeolian sand was added to improve the anti-pressure ability of the loess,and the corresponding ground processing & transportation system was designed.
基金supported by National Natural Science Foundation of China(41474115,42174155)Open Fund of Key Laboratory of Exploration Technologies for Oil and Gas Resources(Yangtze University)Ministry of Education of China(No K2018-02)。
文摘The distributions of local velocity and local phase holdup along the radial direction of pipes are complicated because of gravity differentiation,and the distribution of fluid velocity fi eld changes along the gravity direction in horizontal wells.Therefore,measuring the mixture flow and water holdup is difficult,resulting in poor interpretation accuracy of the production logging output profile.In this paper,oil–water two-phase flow dynamic simulation logging experiments in horizontal oil–water two-phase fl ow simulation wells were conducted using the Multiple Array Production Suite,which comprises a capacitance array tool(CAT)and a spinner array tool(SAT),and then the response characteristics of SAT and CAT in diff erent fl ow rates and water cut production conditions were studied.According to the response characteristics of CAT in diff erent water holdup ranges,interpolation imaging along the wellbore section determines the water holdup distribution,and then,the oil–water two-phase velocity fi eld in the fl ow section was reconstructed on the basis of the fl ow section water holdup distribution and the logging value of SAT and combined with the rheological equation of viscous fl uid,and the calculation method of the oil–water partial phase fl ow rate in the fl ow section was proposed.This new approach was applied in the experiment data calculations,and the results are basically consistent with the experimental data.The total fl ow rate and water holdup from the calculation are in agreement with the set values in the experiment,suggesting that the method has high accuracy.
基金National Natural Science Foundation of China (No. 40275004)State Key Laboratory of Atmosphere Physics and Chemistry
文摘Based on the existing Land Surface Physical Process Models(Deardorff, Dickinson, LIU, Noilhan, Seller, ZHAO), a Comprehensive Land Surface Physical Process Model (CLSPPM) is developed by considering the different physical processes of the earth's surface-vegetation-atmosphere system more completely. Compared with SiB and BATS, which are famous for their detailed parameterizations of physical variables, this simplified model is more convenient and saves much more computation time. Though simple, the feas...
基金Supported by the National Natural Science Foundation of China under Grant Nos 61574019,61674018 and 61674020the Fund of State Key Laboratory of Information Photonics and Optical Communicationsthe Specialized Research Fund for the Doctoral Program of Higher Education of China under Grant No 20130005130001
文摘Two measurement techniques are investigated to characterize photodetector linearity. A model for the two-tone and three-tone photodetector systems is developed to thoroughly investigate the influences of setup components on the measurement results. We demonstrate that small bias shifts from the quadrature point of the modulator will induce deviation into measurement results of the two-tone system, and the simulation results correspond well to experimental and calculation results.
基金National Innovation and Entrepreneurship Program for College Students(202218213001)Science and Technology Innovation Strategy of Guangdong Province(Science and Technology Innovation Cultivation of University Students 2020329182130C000002).
文摘Background Most existing chemical experiment teaching systems lack solid immersive experiences,making it difficult to engage students.To address these challenges,we propose a chemical simulation teaching system based on virtual reality and gesture interaction.Methods The parameters of the models were obtained through actual investigation,whereby Blender and 3DS MAX were used to model and import these parameters into a physics engine.By establishing an interface for the physics engine,gesture interaction hardware,and virtual reality(VR)helmet,a highly realistic chemical experiment environment was created.Using code script logic,particle systems,as well as other systems,chemical phenomena were simulated.Furthermore,we created an online teaching platform using streaming media and databases to address the problems of distance teaching.Results The proposed system was evaluated against two mainstream products in the market.In the experiments,the proposed system outperformed the other products in terms of fidelity and practicality.Conclusions The proposed system which offers realistic simulations and practicability,can help improve the high school chemistry experimental education.
基金National High Technology Research and Development Program of China“Fundamental Study on Formation and Distribution of Hydrocarbon Resources in Deep-water Basins,South China Sea”(No.2009CB219400).
文摘Tofigure out the process and controlling factors of gas reservoir formation in deep-waters,based on an analysis of geological features,source of natural gas and process of reservoir formation in the Liwan 3-1 gasfield,physical simulation experiment of the gas reservoir formation process has been performed,consequently,pattern and features of gas reservoir formation in the Baiyun sag has been found out.The results of the experiment show that:①the formation of the Liwan 3-1 faulted anticline gasfield is closely related to the longstanding active large faults,where natural gas is composed of a high proportion of hydrocarbons,a small amount of non-hydrocarbons,and the wet gas generated during highly mature stage shows obvious vertical migration signs;②liquid hydrocarbons associated with natural gas there are derived from source rock of the Enping&Zhuhai Formation,whereas natural gas comes mainly from source rock of the Enping Formation,and source rock of the Wenchang Formation made a little contribution during the early Eocene period as well;③although there was gas migration and accumulation,yet most of the natural gas mainly scattered and dispersed due to the stronger activity of faults in the early period;later as fault activity gradually weakened,gas started to accumulate into reservoirs in the Baiyun sag;④there is stronger vertical migration of oil and gas than lateral migration,and the places where fault links effective source rocks with reservoirs are most likely for gas accumulation;⑤effective temporal-spatial coupling of source-fault-reservoir in late stage is the key to gas reservoir formation in the Baiyun sag;⑥the nearer the distance from a trap to a large-scale fault and hydrocarbon source kitchen,the more likely gas may accumulate in the trap in late stage,therefore gas accumulation efficiency is much lower for the traps which are far away from large-scale faults and hydrocarbon source kitchens.
基金Project"863":Physical Model-based Dynamic Evolution Technology of a Complex Scene(2015AA016404)the SDUST Excellent Teaching Team Construction Plan.
文摘Background Machine learning-based beer bottle-defect detection is a complex technology that runs automatically;however,it consumes considerable memory,is expensive,and poses a certain danger when training novice operators.Moreover,some topics are difficult to learn from experimental lectures,such as digital image processing and computer vision.However,virtual simulation experiments have been widely used to good effect within education.A virtual simulation of the design and manufacture of a beer bottle-defect detection system will not only help the students to increase their image-processing knowledge,but also improve their ability to solve complex engineering problems and design complex systems.Methods The hardware models for the experiment(camera,light source,conveyor belt,power supply,manipulator,and computer)were built using the 3DS MAX modeling and animation software.The Unreal Engine 4(UE4)game engine was utilized to build a virtual design room,design the interactive operations,and simulate the system operation.Results The results showed that the virtual-simulation system received much better experimental feedback,which facilitated the design and manufacture of a beer bottle-defect detection system.The specialized functions of the functional modules in the detection system,including a basic experimental operation menu,power switch,image shooting,image processing,and manipulator grasping,allowed students(or virtual designers)to easily build a detection system by retrieving basic models from the model library,and creating the beer-bottle transportation,image shooting,image processing,defect detection,and defective-product removal.The virtual simulation experiment was completed with image processing as the main body.Conclusions By mainly focusing on bottle mouth defect detection,the detection system dedicates more attention to the user and the task.With more detailed tasks available,the virtual system will eventually yield much better results as a training tool for image processing education.In addition,a novel visual perception-thinking pedagogical framework enables better comprehension than the traditional lecture-tutorial style.
基金National Natural Science Foundation of China (Granted No.50808005)National"11-5"Science and Technology Supporting Program(Granted No.2006BAJ27B04)Major Program of Beijing Municipal Natural Science Foundation(Granted No.8100001)
文摘According to the service environment of subway structure,experiment is carried out to simulate influence of different loading levels to reinforcement corrosion of R.C element affected by stray current and chlorine salt solution. The current density of the corrosion is measured with the linear polarization resistance method,together with the qualitative analysis and quantitative calculation. Experiment shows that rebar corrosion current density increase accordingly with the increase of loading level. The quantitative relations and the time of rust corrosion of reinforcement are obtained.
文摘Surface sediment samples taken from the East China Sea off the Changjiang estuary are used as raw materials for phosphorus releasing experiment. It is found that after being thoroughly mixed with seawater for about 10 minutes, phosphorus released from the sediments reaches its maximum value. Adsorption kinetics can be fitted with both Elovich equation and two-constant rate equation. The releasing amount is closely related to the composition of the sediments. Phosphorus release from silty and muddy sediment is higher than from that dominated by sandy composition. For the desorption reaction, iron-phosphorus (Fe-P) is the most active one, with a releasing ratio higher than other phosphorus forms, followed by absorbed-phosphorus (Ad-P) and organic bound phosphorus (OP). All of them can be referred to as bio-available phosphorus. The results demonstrate that phosphorus in sediments can be released into seawater under suitable hydrodynamic conditions, and have a great impact on the nutrition state and primary productivity of marine biosphere.
