This study tested the electrical conductivity and pressure sensitivity of lime⁃improved silty sand reinforced with Carbon Fiber Powder(CFP)as the conductive medium.The influence of CFP dosage,moisture content and curi...This study tested the electrical conductivity and pressure sensitivity of lime⁃improved silty sand reinforced with Carbon Fiber Powder(CFP)as the conductive medium.The influence of CFP dosage,moisture content and curing duration on the unconfined compressive strength,initial resistivity and pressure sensitivity of the improved soil was systematically analysed.The results showed that the unconfined compressive strength varied non⁃monotonically with increasing CFP dosage,reaching a peak at a dosage of 1.6%.Furthermore,the initial resistivity showed slight variations under different moisture conditions but eventually converged towards the conductive percolation threshold at a dosage of 2.4%.It is worth noting that CFP reinforced lime⁃improved silty sand(CRLS)exhibit a clear dynamic synchronization of strain with stress and resistivity rate of variation.The pressure sensitivity was optimized with CFP dosages ranging from 1.6%to 2.0%.Both insufficient and excessive dosages had a negative impact on pressure sensitivity.It is important to consider the weakening effect of high moisture content on the pressure sensitivity of the specimens in practical applications.展开更多
The soil construction materials cured with biopolymers are gradually being recognized and widely used in engineering areas,such as roadbeds or foundation fills.The strength of biopolymer-solidified soils(BSS)is easily...The soil construction materials cured with biopolymers are gradually being recognized and widely used in engineering areas,such as roadbeds or foundation fills.The strength of biopolymer-solidified soils(BSS)is easily influenced by the change of internal residual moisture content(RMC),however,the quantitative relationship between them remains unclear.Xanthan gum,as a representative of biopolymer,was used in this study to enhance the mechanical properties of silty sand dredged from the Yellow River under different initial water contents and curing temperatures.The unconfined compressive strength(UCS),curing time,water stability and microscopic properties of BSS were investigated via a series of indoor experiments.Results show that the proposed method for quantitatively evaluating the BSS strength using different RMC values was found to be workable compared to that of the traditional cement-treated method under different curing ages.The curing time required for BSS to reach a certain target strength,i.e.2900 kPa,is reduced to 9.3 h at a higher curing temperature of 90℃.Moreover,BSS exhibits the“self-healing”properties of strength recovery after re-temperature drying,with a strength recovery ratio above 45%.The control raw soil samples completely disintegrate in water within 10 s,and even lower xanthan gum biopolymer dosages,such as 0.5%,improved stability in water by reducing permeability by sealing the internal voids of the soil.SEM results indicate that the initial water content and curing temperature mainly affect the distribution of effective xanthan gum linkages,and thus significantly improve the strength and water stability of BSS.展开更多
Under repeated freezing and thawing in deep seasonal frozen regions, the stability and strength of the soil are imposed in the form of large uneven settlement, instability and strength reduction, which affect the norm...Under repeated freezing and thawing in deep seasonal frozen regions, the stability and strength of the soil are imposed in the form of large uneven settlement, instability and strength reduction, which affect the normal operation of railway lines. This study is to obtain the influencing rules of freeze-thaw on the dynamic properties （dynamic strain, confining pressure and compactness） of silty sand. Based on an amount of inner tests, the dynamic modulus and damping ratio properties of silty soil subjected to repeated freeze-thaw cycles were deeply researched and analyzed. The results are as follows： At the same dynamic strain, the relationship of dynamic stress and freeze-thaw cycles presents negative cor- relation, and the relationship of dynamic stress, confining pressure and compactness present positive correlation. The dynamic modulus double decreases while the damping ratio double increases with incremental increase in dynamic strain. The dynamic modulus sharply decreases while the damping ratio increases with incremental increase in freeze-thaw cycles, and then the changes level off after six freeze-thaw cycles. The dynamic modulus increases while the damping ratio decreases as the confining pressure and compactness increase at the same strain level.展开更多
Corrosion performance of carbon steel in CO2 aqueous environment containing silty sand with different sizes was investigated by immersion tests and electrochemical measurements. Silty sand could form an adsorption lay...Corrosion performance of carbon steel in CO2 aqueous environment containing silty sand with different sizes was investigated by immersion tests and electrochemical measurements. Silty sand could form an adsorption layer on steel surface in initial period, and the sand adsorption layer was turned into a mixture film of silty sand with corrosion product in last period. The adsorption layer in 325 mesh condition （large size） had the fewest pores for H2CO3 transport, exhibiting the highest cathodic current inhibition. In spite of little corrosion product, the sand adsorption film formed in 325 mesh condition induced the lowest corrosion rate. For 1000 and 5000 mesh silty sand, the sand adsorption layer had some pores for H2CO3 transport, leading to low cathodic current inhibition and much matrix dissolution. But the adsorption layer for 5000 mesh silty sand （small size） had the largest special surface area to accelerate heterogeneous precipitation of corrosion product FeCO3. Therefore, the mixture film in 5000 mesh condition was more compact, exhibiting stronger anodic inhibition and lower corrosion rate than those in 1000 mesh condition.展开更多
In cold regions,the creep characteristics of warm frozen silty sand have significant effect on the stability of slope and subgrade.To investigate the creep behavior of warm frozen silty sand under thermo-mechanical co...In cold regions,the creep characteristics of warm frozen silty sand have significant effect on the stability of slope and subgrade.To investigate the creep behavior of warm frozen silty sand under thermo-mechanical coupling loads,a series of triaxial creep tests were carried out under different temperatures and stresses.The test results reveal that the creep strains decrease as the consolidation stress increases,and finally tend to be equal under the same loading stress,regardless of whether the stress is isotropic or deviatoric.Additionally,warm frozen silty sand is highly sensitive to temperature,which greatly influences the creep strain both in the consolidation stage and loading stage.Furthermore,based on the creep test phenomena,a new creep model that considers the influence of the stress level,temperature,hardening,and damage effect was established and experimentally validated.Finally,the sensitivity of the model parameters was analyzed,and it was found that the creep curve transitions from the attenuation creep stage to the non-attenuation creep stage as the temperature coefficient and stress coefficient increases.The hardening effect gradually changes to the damage effect as the coupling coefficient of the hardening and damage increases.展开更多
The objective of this study is to determine the influence of the surrounding soils on the granular properties of the silty sands of Togo and on the resistance of the mortars. Sand compositions are made by substituting...The objective of this study is to determine the influence of the surrounding soils on the granular properties of the silty sands of Togo and on the resistance of the mortars. Sand compositions are made by substituting silty sands with clay soil, vegetal soil, lateritic soil or fine elements (<0.08 mm) which are the surrounding land polluting the sands in Togo. After identification tests, the mixtures were used to prepare test specimens of mortar which are subjected to bending and compression. It appears that additions of clay and plastic soils (ES = 0, VBM > 0.53 and IP > 19) from 10% to 35% cause drops in resistance of mortars from 7% to 96%;this loss is 8% to 70% for the rates of addition of less clayey soil (ES = 33, VBM = 0.40 and IP = 0) at rates of 10% to 100%. As for fine powdery soils (ES = 56.53 and VBM = 0.25), they have virtually no influence on resistance (loss of less than 3% for rates of 100%). Construction stakeholders thus have a decision-making tool for the choice of silty sand extraction zones according to the surrounding land and the quality of the desired concrete.展开更多
In this paper, flume experiments are focused on sediment transport inside and outside the surf zone. According to the energy dissipation balance principle of sediment-laden flow and the similarity between energy dissi...In this paper, flume experiments are focused on sediment transport inside and outside the surf zone. According to the energy dissipation balance principle of sediment-laden flow and the similarity between energy dissipation of spilling breaking wave and hydraulic jump, formulas are proposed to predict time averaged suspended sediment concentration under both non-breaking and breaking waves. Assuming that the sediment diffusion coefficient, which is related with energy dissipation, is proportional to water depth, formulas are proposed to predict close-to-bed suspended sediment concentration and vertical distribution of suspended sediment under spilling breaking waves, and the prediction shows a good agreement with the measurement.展开更多
The ruin of several civil engineering works occurs due to shear rupture of the ground. When the stress is greater than the shear resistance, the internal friction angle and the cohesion of the soil loosen and rupture ...The ruin of several civil engineering works occurs due to shear rupture of the ground. When the stress is greater than the shear resistance, the internal friction angle and the cohesion of the soil loosen and rupture occurs. Cement and lime are often used to stabilize soils and improve soil strength. The costs and environmental problems of these technologies raise concerns and challenge researchers to innovate with clean, inexpensive materials, accessible to the most disadvantaged social classes. The question that this study seeks to answer is whether the binders derived from plant tannins, which also stabilize soils, improve the shear resistance of these soils. To do this, we determined for silty sand the shear parameters, notably the cohesion and the angle of internal friction in the non-stabilized state and when they are stabilized with the powder of the bark of the Bridelia under different water states. The results show that the addition of Bridelia powder to silty sand increases the cohesion of the soil by nearly 70.71% and the friction angle by 4.31%. But in unfavourable water conditions, the cohesion and internal friction angle of the silty sand material improved with Bridelia bark powder drops drastically by nearly 81.56%. but does not dissolve completely as for the same material. When it is not stabilized. This information is an invaluable contribution in the search for solutions to increase the durability of earthen constructions by improving the water-repellent properties of soils.展开更多
Mechanical behavior such as stress-strain response, shear strength, resistance to liquefaction, modulus, and shear wave velocity of granular mixes containing coarse and fine grains is dependent on intergrain contact d...Mechanical behavior such as stress-strain response, shear strength, resistance to liquefaction, modulus, and shear wave velocity of granular mixes containing coarse and fine grains is dependent on intergrain contact density of the soil. The global void ratio e is a poor index of contact density for such soils. The contact density depends on void ratio, fine grain content （Cv）, size disparity between particles, and gradation among other factors. A simple analysis of a two-sized particle system with large size disparity is used to develop an understanding of the effects of Cv, e, and gradation of coarse and fine grained soils in the soil mix on intergrain contact density. An equivalent intergranular void ratio （ec）oq is introduced as a useful intergrain contact density for soils at fines content of less than a threshold value Crth. Beyond this value, an equivalent interfine void ratio （ef）eq is introduced as a primary intergrain contact density index. At higher values of Cv beyond a limiting value of fine grains content CVL, an interfine void ratio ef is introduced as the primary contact density index. Relevant equivalent relative density indices （Drc）eq and （Drf）eq are also presented. Experimental data show that these new indices correlate well with steady state strength, liquefaction resistance, and shear wave velocities of sands, silty sands, sandy silts, and gravelly sand mixes.展开更多
Whether the presence of non-plastic silt in a granular mix soil impact its liquefaction potential and how to evaluate liquefaction resistance of sand containing different amounts of silt contents are both controversia...Whether the presence of non-plastic silt in a granular mix soil impact its liquefaction potential and how to evaluate liquefaction resistance of sand containing different amounts of silt contents are both controversial issues. This paper presents the results of an experimental evaluation to address these issues. Two parameters, namely, equivalent intergranular void ratio （ec）eq and equivalent interfine void ratio （ef）eq, proposed in a companion paper （Thevanayagam, 2007） as indices of active grain contacts in a granular mix, are used to characterize liquefaction resistance of sands and silty sands. Results indicate that, at the same global void ratio （e）, liquefaction resistance of silty sand decreases with an increase in fines content （Cv） up to a threshold value （Crth）. This is due to a reduction in intergrain contact density between the coarse grains. Beyond Crth, with further addition of fines, the interfine contacts become significant while the inter-coarse grain contacts diminish and coarse grains become dispersed. At the same e, the liquefaction resistance increases and the soil becomes stronger with a fttrther increase in silt content. Beyond a limiting fines content （CrL）, the liquefaction resistance is controlled by interfine contacts only. When Cr〈Crth, at the same （e）eq, the liquefaction resistance of silty sand is comparable to that of the host clean sand at a void ratio equal to （ec）eq. When CF〉CFth, at the same （ef）eq, the cyclic strength of a sandy silt is comparable to the host silt at a void ratio equal to （ef）eq.展开更多
The understanding of rainfall-induced landslides on gentle, loose-fill slopes is limited in comparison to steep slopes. Hence, two physical model tests were conducted on silty sand slopes under continuous rainfall: on...The understanding of rainfall-induced landslides on gentle, loose-fill slopes is limited in comparison to steep slopes. Hence, two physical model tests were conducted on silty sand slopes under continuous rainfall: one on a bare slope and the other on a slope planted with ryegrass. The slope angle of 25° is much lower than the internal friction angle of slope material (34.3°), which makes the model test fall well into the category of gentle slope. For the initially unsaturated bare slope, a rainfall event with return period of 18 years could trigger a rapid and retrogressive global sliding, which differs from previous findings that gentle slopes would only experience shallow failure. A sudden increase in pore-water pressure was simultaneously observed, which might be generated by the wetting-induced collapse of unsaturated loose soil. On the other hand, the stability of the slope with grass plantation was significantly enhanced, and it was able to withstand rainfall event more severe than those with a return period of 100 years, with only minimal deformation. The results suggest that the gain in shear strength due to ryegrass roots surpasses the additional sliding force caused by the increased water retention capability. Additionally, it is found that the abrupt change in pore pressure was no longer indicative of slope failure in the case of the grass-reinforced slope.展开更多
A numerical simulation approach was adopted to investigate the uplift bearing characteristics of helical an-chors in Nantong silty sand and to predict their uplift bear-ing capacity.Finite element model validation was...A numerical simulation approach was adopted to investigate the uplift bearing characteristics of helical an-chors in Nantong silty sand and to predict their uplift bear-ing capacity.Finite element model validation was per-formed,and the uplift bearing mechanism of helical anchors was analyzed.The current code’s uplift bearing capacity calculation formula was optimized,and the accuracy and re-liability of the modified formula were evaluated.The results indicate that the critical embedment depth ratio of the anchor plate in Nantong silty sand is 5,and the critical spacing ra-tio ranges from 3 to 4.The current code’s formula underes-timates the uplift bearing capacity of helical anchors under these conditions.To improve the prediction accuracy,the optimization coefficients M and L,which account for the embedment depth ratio of the anchor plate,are introduced,and fitting formulas for these coefficients are provided to im-prove the prediction of uplift bearing capacity in Nantong silty sand and to serve as a reference for similar engineering applications.展开更多
The clay mineral composition is one of the major factors that governs the physical properties of silty sand subgrade. Therefore, a thorough knowledge of mineral composition is essential to predict the optimum engineer...The clay mineral composition is one of the major factors that governs the physical properties of silty sand subgrade. Therefore, a thorough knowledge of mineral composition is essential to predict the optimum engineering properties of the soil, which is generally characterized by different indices like maximum dry density （MDD）, California bearing ratio （CBR）, unconfined compressive strength （UCS） and free swelling index （FSI）. In this article, a novel multi- attribute decision making （MADM） based approach of mix design has been proposed for silty sand- artificial clay mix to improve the characteristic strength of a soil subgrade. Experimental investigation has been carried out in this study to illustrate the proposed approach of selecting appropriate proportion for the soil mix to optimize all the above mentioned engineering properties simultaneously. The results show that a mix proportion containing approximately 90% silty sand plus 10% bentonite soil is the optimal combination in context to the present study. The proposed methodology for optimal decision making to choose appropriate combination of bentonite and silty sand is general in nature and therefore, it can be extended to other problems of selecting mineral compositions.展开更多
基金Sponsored by Jilin Provincial Department of Education Scientific Research Project(Grant Nos.JJKH20190875KJ,JJKH20230348KJ).
文摘This study tested the electrical conductivity and pressure sensitivity of lime⁃improved silty sand reinforced with Carbon Fiber Powder(CFP)as the conductive medium.The influence of CFP dosage,moisture content and curing duration on the unconfined compressive strength,initial resistivity and pressure sensitivity of the improved soil was systematically analysed.The results showed that the unconfined compressive strength varied non⁃monotonically with increasing CFP dosage,reaching a peak at a dosage of 1.6%.Furthermore,the initial resistivity showed slight variations under different moisture conditions but eventually converged towards the conductive percolation threshold at a dosage of 2.4%.It is worth noting that CFP reinforced lime⁃improved silty sand(CRLS)exhibit a clear dynamic synchronization of strain with stress and resistivity rate of variation.The pressure sensitivity was optimized with CFP dosages ranging from 1.6%to 2.0%.Both insufficient and excessive dosages had a negative impact on pressure sensitivity.It is important to consider the weakening effect of high moisture content on the pressure sensitivity of the specimens in practical applications.
基金support provided by the Major science and technology program of Inner Mongolia,China(Grant No.2021ZD0007)National Natural Science Foundation of China(Grant Nos.51979267 and 52074143).
文摘The soil construction materials cured with biopolymers are gradually being recognized and widely used in engineering areas,such as roadbeds or foundation fills.The strength of biopolymer-solidified soils(BSS)is easily influenced by the change of internal residual moisture content(RMC),however,the quantitative relationship between them remains unclear.Xanthan gum,as a representative of biopolymer,was used in this study to enhance the mechanical properties of silty sand dredged from the Yellow River under different initial water contents and curing temperatures.The unconfined compressive strength(UCS),curing time,water stability and microscopic properties of BSS were investigated via a series of indoor experiments.Results show that the proposed method for quantitatively evaluating the BSS strength using different RMC values was found to be workable compared to that of the traditional cement-treated method under different curing ages.The curing time required for BSS to reach a certain target strength,i.e.2900 kPa,is reduced to 9.3 h at a higher curing temperature of 90℃.Moreover,BSS exhibits the“self-healing”properties of strength recovery after re-temperature drying,with a strength recovery ratio above 45%.The control raw soil samples completely disintegrate in water within 10 s,and even lower xanthan gum biopolymer dosages,such as 0.5%,improved stability in water by reducing permeability by sealing the internal voids of the soil.SEM results indicate that the initial water content and curing temperature mainly affect the distribution of effective xanthan gum linkages,and thus significantly improve the strength and water stability of BSS.
基金funded by the National Key Basic Research Development Plan of China (Grant No. 2012CB026104)the National Natural Science Foundation (NSFC) of China (Grant Nos.51208320 and 51171281)
文摘Under repeated freezing and thawing in deep seasonal frozen regions, the stability and strength of the soil are imposed in the form of large uneven settlement, instability and strength reduction, which affect the normal operation of railway lines. This study is to obtain the influencing rules of freeze-thaw on the dynamic properties （dynamic strain, confining pressure and compactness） of silty sand. Based on an amount of inner tests, the dynamic modulus and damping ratio properties of silty soil subjected to repeated freeze-thaw cycles were deeply researched and analyzed. The results are as follows： At the same dynamic strain, the relationship of dynamic stress and freeze-thaw cycles presents negative cor- relation, and the relationship of dynamic stress, confining pressure and compactness present positive correlation. The dynamic modulus double decreases while the damping ratio double increases with incremental increase in dynamic strain. The dynamic modulus sharply decreases while the damping ratio increases with incremental increase in freeze-thaw cycles, and then the changes level off after six freeze-thaw cycles. The dynamic modulus increases while the damping ratio decreases as the confining pressure and compactness increase at the same strain level.
基金the funding support from the National Natural Science Foundation of China(Project No.51571027)the National Environmental Corrosion Platform(NECP)
文摘Corrosion performance of carbon steel in CO2 aqueous environment containing silty sand with different sizes was investigated by immersion tests and electrochemical measurements. Silty sand could form an adsorption layer on steel surface in initial period, and the sand adsorption layer was turned into a mixture film of silty sand with corrosion product in last period. The adsorption layer in 325 mesh condition （large size） had the fewest pores for H2CO3 transport, exhibiting the highest cathodic current inhibition. In spite of little corrosion product, the sand adsorption film formed in 325 mesh condition induced the lowest corrosion rate. For 1000 and 5000 mesh silty sand, the sand adsorption layer had some pores for H2CO3 transport, leading to low cathodic current inhibition and much matrix dissolution. But the adsorption layer for 5000 mesh silty sand （small size） had the largest special surface area to accelerate heterogeneous precipitation of corrosion product FeCO3. Therefore, the mixture film in 5000 mesh condition was more compact, exhibiting stronger anodic inhibition and lower corrosion rate than those in 1000 mesh condition.
基金supported the National Natural Science Foundation of China (No.41971076)the National Key Research and Development Program of China (No.2016YFE0202400)the State Key Laboratory of Road Engineering Safety and Health in Cold and High-altitude Regions (No.YGY2017KYPT-04)。
文摘In cold regions,the creep characteristics of warm frozen silty sand have significant effect on the stability of slope and subgrade.To investigate the creep behavior of warm frozen silty sand under thermo-mechanical coupling loads,a series of triaxial creep tests were carried out under different temperatures and stresses.The test results reveal that the creep strains decrease as the consolidation stress increases,and finally tend to be equal under the same loading stress,regardless of whether the stress is isotropic or deviatoric.Additionally,warm frozen silty sand is highly sensitive to temperature,which greatly influences the creep strain both in the consolidation stage and loading stage.Furthermore,based on the creep test phenomena,a new creep model that considers the influence of the stress level,temperature,hardening,and damage effect was established and experimentally validated.Finally,the sensitivity of the model parameters was analyzed,and it was found that the creep curve transitions from the attenuation creep stage to the non-attenuation creep stage as the temperature coefficient and stress coefficient increases.The hardening effect gradually changes to the damage effect as the coupling coefficient of the hardening and damage increases.
文摘The objective of this study is to determine the influence of the surrounding soils on the granular properties of the silty sands of Togo and on the resistance of the mortars. Sand compositions are made by substituting silty sands with clay soil, vegetal soil, lateritic soil or fine elements (<0.08 mm) which are the surrounding land polluting the sands in Togo. After identification tests, the mixtures were used to prepare test specimens of mortar which are subjected to bending and compression. It appears that additions of clay and plastic soils (ES = 0, VBM > 0.53 and IP > 19) from 10% to 35% cause drops in resistance of mortars from 7% to 96%;this loss is 8% to 70% for the rates of addition of less clayey soil (ES = 33, VBM = 0.40 and IP = 0) at rates of 10% to 100%. As for fine powdery soils (ES = 56.53 and VBM = 0.25), they have virtually no influence on resistance (loss of less than 3% for rates of 100%). Construction stakeholders thus have a decision-making tool for the choice of silty sand extraction zones according to the surrounding land and the quality of the desired concrete.
基金supported by special fund for important and large scientific and technical projects from the Ministry of Communications (Grant No. 201132874660)funds from Nanjing Hydraulic Research Institute (Grant No. Y210001)
文摘In this paper, flume experiments are focused on sediment transport inside and outside the surf zone. According to the energy dissipation balance principle of sediment-laden flow and the similarity between energy dissipation of spilling breaking wave and hydraulic jump, formulas are proposed to predict time averaged suspended sediment concentration under both non-breaking and breaking waves. Assuming that the sediment diffusion coefficient, which is related with energy dissipation, is proportional to water depth, formulas are proposed to predict close-to-bed suspended sediment concentration and vertical distribution of suspended sediment under spilling breaking waves, and the prediction shows a good agreement with the measurement.
文摘The ruin of several civil engineering works occurs due to shear rupture of the ground. When the stress is greater than the shear resistance, the internal friction angle and the cohesion of the soil loosen and rupture occurs. Cement and lime are often used to stabilize soils and improve soil strength. The costs and environmental problems of these technologies raise concerns and challenge researchers to innovate with clean, inexpensive materials, accessible to the most disadvantaged social classes. The question that this study seeks to answer is whether the binders derived from plant tannins, which also stabilize soils, improve the shear resistance of these soils. To do this, we determined for silty sand the shear parameters, notably the cohesion and the angle of internal friction in the non-stabilized state and when they are stabilized with the powder of the bark of the Bridelia under different water states. The results show that the addition of Bridelia powder to silty sand increases the cohesion of the soil by nearly 70.71% and the friction angle by 4.31%. But in unfavourable water conditions, the cohesion and internal friction angle of the silty sand material improved with Bridelia bark powder drops drastically by nearly 81.56%. but does not dissolve completely as for the same material. When it is not stabilized. This information is an invaluable contribution in the search for solutions to increase the durability of earthen constructions by improving the water-repellent properties of soils.
文摘Mechanical behavior such as stress-strain response, shear strength, resistance to liquefaction, modulus, and shear wave velocity of granular mixes containing coarse and fine grains is dependent on intergrain contact density of the soil. The global void ratio e is a poor index of contact density for such soils. The contact density depends on void ratio, fine grain content （Cv）, size disparity between particles, and gradation among other factors. A simple analysis of a two-sized particle system with large size disparity is used to develop an understanding of the effects of Cv, e, and gradation of coarse and fine grained soils in the soil mix on intergrain contact density. An equivalent intergranular void ratio （ec）oq is introduced as a useful intergrain contact density for soils at fines content of less than a threshold value Crth. Beyond this value, an equivalent interfine void ratio （ef）eq is introduced as a primary intergrain contact density index. At higher values of Cv beyond a limiting value of fine grains content CVL, an interfine void ratio ef is introduced as the primary contact density index. Relevant equivalent relative density indices （Drc）eq and （Drf）eq are also presented. Experimental data show that these new indices correlate well with steady state strength, liquefaction resistance, and shear wave velocities of sands, silty sands, sandy silts, and gravelly sand mixes.
文摘Whether the presence of non-plastic silt in a granular mix soil impact its liquefaction potential and how to evaluate liquefaction resistance of sand containing different amounts of silt contents are both controversial issues. This paper presents the results of an experimental evaluation to address these issues. Two parameters, namely, equivalent intergranular void ratio （ec）eq and equivalent interfine void ratio （ef）eq, proposed in a companion paper （Thevanayagam, 2007） as indices of active grain contacts in a granular mix, are used to characterize liquefaction resistance of sands and silty sands. Results indicate that, at the same global void ratio （e）, liquefaction resistance of silty sand decreases with an increase in fines content （Cv） up to a threshold value （Crth）. This is due to a reduction in intergrain contact density between the coarse grains. Beyond Crth, with further addition of fines, the interfine contacts become significant while the inter-coarse grain contacts diminish and coarse grains become dispersed. At the same e, the liquefaction resistance increases and the soil becomes stronger with a fttrther increase in silt content. Beyond a limiting fines content （CrL）, the liquefaction resistance is controlled by interfine contacts only. When Cr〈Crth, at the same （e）eq, the liquefaction resistance of silty sand is comparable to that of the host clean sand at a void ratio equal to （ec）eq. When CF〉CFth, at the same （ef）eq, the cyclic strength of a sandy silt is comparable to the host silt at a void ratio equal to （ef）eq.
基金National Key R&D Program of China(2021YFC3001000)the National Natural Science Foundation of China(52239008,52108311,and 52025094)the Shenzhen Science and Technology Program(KQTD20210811090112003 and GXWD20231130125225001)for financial supports.
文摘The understanding of rainfall-induced landslides on gentle, loose-fill slopes is limited in comparison to steep slopes. Hence, two physical model tests were conducted on silty sand slopes under continuous rainfall: one on a bare slope and the other on a slope planted with ryegrass. The slope angle of 25° is much lower than the internal friction angle of slope material (34.3°), which makes the model test fall well into the category of gentle slope. For the initially unsaturated bare slope, a rainfall event with return period of 18 years could trigger a rapid and retrogressive global sliding, which differs from previous findings that gentle slopes would only experience shallow failure. A sudden increase in pore-water pressure was simultaneously observed, which might be generated by the wetting-induced collapse of unsaturated loose soil. On the other hand, the stability of the slope with grass plantation was significantly enhanced, and it was able to withstand rainfall event more severe than those with a return period of 100 years, with only minimal deformation. The results suggest that the gain in shear strength due to ryegrass roots surpasses the additional sliding force caused by the increased water retention capability. Additionally, it is found that the abrupt change in pore pressure was no longer indicative of slope failure in the case of the grass-reinforced slope.
基金The National Natural Science Foundation of China (No. 52378329)。
文摘A numerical simulation approach was adopted to investigate the uplift bearing characteristics of helical an-chors in Nantong silty sand and to predict their uplift bear-ing capacity.Finite element model validation was per-formed,and the uplift bearing mechanism of helical anchors was analyzed.The current code’s uplift bearing capacity calculation formula was optimized,and the accuracy and re-liability of the modified formula were evaluated.The results indicate that the critical embedment depth ratio of the anchor plate in Nantong silty sand is 5,and the critical spacing ra-tio ranges from 3 to 4.The current code’s formula underes-timates the uplift bearing capacity of helical anchors under these conditions.To improve the prediction accuracy,the optimization coefficients M and L,which account for the embedment depth ratio of the anchor plate,are introduced,and fitting formulas for these coefficients are provided to im-prove the prediction of uplift bearing capacity in Nantong silty sand and to serve as a reference for similar engineering applications.
文摘The clay mineral composition is one of the major factors that governs the physical properties of silty sand subgrade. Therefore, a thorough knowledge of mineral composition is essential to predict the optimum engineering properties of the soil, which is generally characterized by different indices like maximum dry density （MDD）, California bearing ratio （CBR）, unconfined compressive strength （UCS） and free swelling index （FSI）. In this article, a novel multi- attribute decision making （MADM） based approach of mix design has been proposed for silty sand- artificial clay mix to improve the characteristic strength of a soil subgrade. Experimental investigation has been carried out in this study to illustrate the proposed approach of selecting appropriate proportion for the soil mix to optimize all the above mentioned engineering properties simultaneously. The results show that a mix proportion containing approximately 90% silty sand plus 10% bentonite soil is the optimal combination in context to the present study. The proposed methodology for optimal decision making to choose appropriate combination of bentonite and silty sand is general in nature and therefore, it can be extended to other problems of selecting mineral compositions.
