Large-scale doubly-fed induction generator(DFIG)wind turbines are connected to the grid and required to remain grid-connection during faults,the short-circuit current contributed by the generation has become a signifi...Large-scale doubly-fed induction generator(DFIG)wind turbines are connected to the grid and required to remain grid-connection during faults,the short-circuit current contributed by the generation has become a significant issue.However,the traditional calculation methods aiming at synchronous generators cannot be directly applied to the DFIG wind turbines.A new method is needed to calculate the short-circuit current required by the planning,protection and control of the power grid.The short-circuit transition of DFIG under symmetrical and asymmetric short-circuit conditions are mathematically deduced,and the short-circuit characteristics of DFIG are analyzed.A new method is proposed to calculate the steady-state short-circuit current of DFIG based on the derived expressions.The time-domain simulations are conducted to verify the accuracy of the proposed method.展开更多
Aiming at the problemthat the traditional short-circuit current calculationmethod is not applicable to Distributed Generation(DG)accessing the distribution network,the paper proposes a short-circuit current partitioni...Aiming at the problemthat the traditional short-circuit current calculationmethod is not applicable to Distributed Generation(DG)accessing the distribution network,the paper proposes a short-circuit current partitioning calculation method considering the degree of voltage drop at the grid-connected point of DG.Firstly,the output characteristics of DG in the process of low voltage ride through are analyzed,and the equivalent output model of DG in the fault state is obtained.Secondly,by studying the network voltage distribution law after fault in distribution networks under different DG penetration rates,the degree of voltage drop at the grid-connected point of DG is used as a partition index to partition the distribution network.Then,iterative computation is performed within each partition,and data are transferred between partitions through split nodes to realize the fast partition calculation of short-circuit current for high proportion DG access to distribution network,which solves the problems of long iteration time and large calculation error of traditional short-circuit current.Finally,a 62-node real distribution network model containing a high proportion of DG access is constructed onMATLAB/Simulink,and the simulation verifies the effectiveness of the short-circuit current partitioning calculation method proposed in the paper,and its calculation speed is improved by 48.35%compared with the global iteration method.展开更多
To study the effects of wind generators on distribution system protection,the short-circuit current(SCC) characteristics of wind generators is important.Although there are many researches on the issue,a clear agreemen...To study the effects of wind generators on distribution system protection,the short-circuit current(SCC) characteristics of wind generators is important.Although there are many researches on the issue,a clear agreement has not been reached so far.The SCC characteristics for different wind generators are studied.PSCAD simulation is performed in the same system integrated with different kinds of wind generators,and their results are compared with those reported in IEEE papers.The detection possibility by overcurrent relay(OCR)is discussed based on the simulation results.展开更多
With the rapid development of economy, strengthen the continuous construction of national infrastructure, etc., many industry demand for steel, steel enterprise capacity expands, at the same time, the steel enterprise...With the rapid development of economy, strengthen the continuous construction of national infrastructure, etc., many industry demand for steel, steel enterprise capacity expands, at the same time, the steel enterprises to positive response to the call of national energy conservation and emission reduction, using plant waste heat green development is the only way to realize the transformation and upgrading of the steel industry. This paper will be mainly for the domestic steel enterprise 6kV system short circuit current exceeds the limit and take the restrictive measures for detailed analysis and discussion for the industry reference.展开更多
When the converter bus voltage of a voltage source converter-based high voltage direct current(VSC-HVDC)system drops below a certain predetermined threshold,the system enters low-voltage ride-through(LVRT)mode to avoi...When the converter bus voltage of a voltage source converter-based high voltage direct current(VSC-HVDC)system drops below a certain predetermined threshold,the system enters low-voltage ride-through(LVRT)mode to avoid overcurrent and potential equipment failure,during which it operates as a controlled current source.The influence mechanism of LVRT control strategies on short-circuit current and overall system stability remains not yet fully and systematically investigated.First,this paper provides an overview of several LVRT strategies for VSC-HVDC systems and examines their effects on short-circuit current contribution.Next,it analyzes in detail the mechanisms through which active and reactive currents injected during LVRT impact system frequency stability,voltage stability,and synchronization stability.To address these interrelated issues,an optimized and comprehensive LVRT strategy incorporating short-circuit current constraints is proposed.The approach determines the active current ratio based on system frequency stability requirements and dynamically adjusts the active current recovery rate via phase control of the VSC-HVDC bus.The remaining capacity is allocated to reactive current support,thereby enhancing voltage and synchronization stability while maintaining sufficient short-circuit current margin and system frequency stability.Finally,simulations conducted on the PSS/E platform,using actual grid data from a selected cross-section system,validate convincingly the effectiveness of the proposed parameter optimization strategy for VSC-HVDC low-voltage ride-through.展开更多
With the load growth and the power grid expansion,the problem of short-circuit current(SCC)exceeding the secure limit in large-scale power grids has become more serious,which poses great challenge to the optimal secur...With the load growth and the power grid expansion,the problem of short-circuit current(SCC)exceeding the secure limit in large-scale power grids has become more serious,which poses great challenge to the optimal secure operation.Aiming at the SCC limitations,we use multiple back-toback voltage source converter based(B2B VSC)systems to separate a large-scale AC power grid into two asynchronous power grids.A multi-objective robust optimal secure operation model of large-scale power grid with multiple B2B VSC systems considering the SCC limitation is established based on the AC power flow equations.The decision variables include the on/off states of synchronous generators,power output,terminal voltage,transmission switching,bus sectionalization,and modulation ratios of B2B VSC systems.The influence of inner current sources of renewable energy generators on the system SCC is also considered.To improve the computational efficiency,a mixedinteger convex programming(MICP)framework based on convex relaxation methods including the inscribed N-sided approximation for the nonlinear SCC limitation constraints is proposed.Moreover,combined with the column-and-constraint generation(C&CG)algorithm,a method to directly solve the compromise optimal solution(COS)of the multi-objective robust optimal secure operation model is proposed.Finally,the effectiveness and computational efficiency of the proposed solution method is demonstrated by an actual 4407-bus provincial power grid and the modified IEEE 39-bus power grid,which can reduce the consumed CPU time of solving the COS by more than 90%and obtain a better COS.展开更多
Low-density short-duration pulsed current-assisted aging treatment was applied to the Ti-6Al-4V-0.5Mo-0.5Zr alloy subjected to different solution treatments.The results show that numerous α_(p) phases redissolve into...Low-density short-duration pulsed current-assisted aging treatment was applied to the Ti-6Al-4V-0.5Mo-0.5Zr alloy subjected to different solution treatments.The results show that numerous α_(p) phases redissolve into the new β phase during the pulsed current-assisted aging process,and then the newly formed β phase is mainly transformed into the β_(t) phase,with occasional transition to new α_(p) phase,leading to a remarkable grain refinement,especially for the lamellarαs phases.In comparison to conventional aging treatment,the pulsed current-assisted aging approach achieves a significant enhancement in strength without degrading ductility,yielding an excellent mechanical property combination:a yield strength of 932 MPa,a tensile strength of 1042 MPa,and an elongation of 12.2%.It is primarily ascribed to the increased fraction of β_(t) phases,the obvious grain refinement effect,and the slip block effect induced by the multiple-variantαs colonies distributed within β_(t) phases.展开更多
This article investigates the robust current tracking control problem of three-phase grid-connected inverters with LCL filter under external disturbance by a dynamic state feedback control method.First,this paper cons...This article investigates the robust current tracking control problem of three-phase grid-connected inverters with LCL filter under external disturbance by a dynamic state feedback control method.First,this paper constructs an internal model to learn the information of the states and input of the grid-connected inverter under steady state.Second,by utilizing the internal model principle,the paper turns the tracking control problem into the robust stabilization control problem based on some appropriate coordinate transformations.Then,The paper designs a dynamics state feedback control law to deal with this robust stabilization problem,and thus the solution of the robust current tracking control problem of three-phase grid-connected inverters can be obtained.This control method can ensure the asymptotic stability of the closedloop system.Finally,the paper illustrates the effectiveness of the proposed control approach through several groups of simulations,and compares it with the feedforward control method to verify the robustness of the proposed control method to uncertain parameters.展开更多
In this paper,a comprehensive evaluation on the silicon/silicon carbide(Si/SiC)hybrid switch is performed through experimental tests in terms of both electrical performance and robustness under extreme stresses.Based ...In this paper,a comprehensive evaluation on the silicon/silicon carbide(Si/SiC)hybrid switch is performed through experimental tests in terms of both electrical performance and robustness under extreme stresses.Based on the optional turn-on and turn-off delay times under the efficiency control mode obtained from the double-pulse test(DPT),both nondestructive and destructive single-pulse avalanche tests are conducted on the Si/SiC hybrid switch as well as on the two discrete device branches inside the hybrid switch.In addition,the avalanche voltage,critical avalanche energy,and peak avalanche current,which intrinsically characterize the unclamped-inductive-switching(UIS)avalanche characteristics,are carefully examined.In this way,the physical factors dominating the UIS characteristics of the hybrid switch,thus limiting its single-pulse avalanche withstand capability,are specifically and comprehensively identified;the underlying physical mechanisms are analyzed and revealed in depth,and how the gate control sequence affects the UIS characteristics of the hybrid switch is extensively investigated.We additionally carry out short-circuit(SC)tests under the fault-under-load(FUL)condition and perform a parallel in-depth analysis to experimentally determine which branch dominates the SC withstand capability of the hybrid switch.Our experimental study indicates that,for both SC robustness and single-pulse avalanche capability,the limiting factor is a single device branch among the two parallel discrete devices,and the UIS behavior is sensitive to the variation of the gate turn-off delay time Toff_delay.The study conducted in this paper not only provides deep academic insights into the electrical performance and reliability of the Si/SiC hybrid switch,but also offers fundamental theoretical principles and technical evidence to support its more efficient and long-term reliable applications of the hybrid switch in the industrial fields.展开更多
Energy density and safety are two crucial parameters when evaluating lithium-metal batteries(LMBs).Herein,we present an ultralight polymer-based current collector,incorporating flame-retardant materials,designed speci...Energy density and safety are two crucial parameters when evaluating lithium-metal batteries(LMBs).Herein,we present an ultralight polymer-based current collector,incorporating flame-retardant materials,designed specifically for thin lithium-metal anodes.Compared to the traditional copper current collector(8.96 mg cm^(-2),10μm thick),the polymer-based current collector(12μm thick)has a significantly lower areal density of 1.41 mg cm^(-2),i.e.,only one-sixth of the copper collector,thus enabling substantially higher energy densities.Accordingly,when employed in Li||NMC_(622)full-cells,the polymer-based current collector enables a specific energy of 449 Wh kg^(-1),representing a notable improvement of about14.5%compared to cells employing a classic copper current collector.The inclusion of Al(OH)_(3) as a flame retardant into the current collector suppresses flammability and,thereby,significantly improves the safety of the resulting LMBs.展开更多
With the advent of the big data era,modern statistics has enjoyed unprecedented development opportunities and also faced numerous new challenges.Traditional statistical computing methods are often limited by issues su...With the advent of the big data era,modern statistics has enjoyed unprecedented development opportunities and also faced numerous new challenges.Traditional statistical computing methods are often limited by issues such as computer memory capacity and distributed storage of data across different locations,and are unable to directly apply to large-scale data sets.Therefore,in the context of big data,designing efficient and theoretically guaranteed statistical learning and inference algorithms has become a key issue that the current field of statistics urgently needs to address.In this paper,the application status of statistical analysis methods in the big data environment was systematically reviewed,and its future development directions were analyzed to provide reference and support for the further development of theory and methods of the statistical analysis of big data.展开更多
Lithium metal batteries(LMBs)are promising candidates for next-generation high-energy-density storage devices.However,an unstable lithium metal anode poses significant issues that critically compromise battery safety ...Lithium metal batteries(LMBs)are promising candidates for next-generation high-energy-density storage devices.However,an unstable lithium metal anode poses significant issues that critically compromise battery safety and cycle life,including lithium dendrite formation,solid electrolyte interphase degradation,dead lithium accumulation,and substantial volume fluctuations during cycling.These problems can be addressed by regulating lithium deposition and suppressing side reactions through the modification of copper current collectors using three classes of materials:metal and metal oxide,carbon,and polymer materials.This review comprehensively examines recent advances in the application of these materials as current collector coatings.Particularly,their distinct roles in the lithium deposition process are analyzed to understand how they mitigate the issues associated with the lithium metal anode.Furthermore,their inherent limitations are considered to inform future research directions.While each class of materials offers specific advantages,multifunctionality is required to effectively regulate lithium deposition.In prospect,a novel composite copper current collector design that integrates the merits of the aforementioned advanced materials is proposed.The insights from this review provide valuable guidance for the rational design of modified copper current collectors,which would significantly improve the safety and cycle life of LMBs and advance their commercialization.展开更多
Transcranial direct current stimulation(tDCS)is a non-invasive technique that modifies cortical excitability and induces neuroplasticity using low-intensity electrical currents.Nuclear medicine technologies like posit...Transcranial direct current stimulation(tDCS)is a non-invasive technique that modifies cortical excitability and induces neuroplasticity using low-intensity electrical currents.Nuclear medicine technologies like positron emission tomography(PET)and single-photon emission computed tomography(SPECT)can quantify cerebral metabolism and other dynamics.Evidence suggests that combining tDCS with these imaging methods enhances understanding and outcomes for neurological and psychiatric conditions.This review highlights how nuclear medicine can objectively characterize tDCS eff ects,map network modulation,and identify predictive biomarkers.PET and SPECT indicate changes in glucose metabolism and neurotransmitter activity post-tDCS,demonstrating their value in validation.While the co-application of these methodologies is still in conceptual stages,their integration may advance precision neuromodulation and inform rehabilitation strategies.展开更多
To elucidate the accelerated degradation mechanisms of metallic interconnects in operational solid oxide fuel cells,the oxidation behavior of FSS430 ferritic stainless steel under the coupling of simultaneous electric...To elucidate the accelerated degradation mechanisms of metallic interconnects in operational solid oxide fuel cells,the oxidation behavior of FSS430 ferritic stainless steel under the coupling of simultaneous electrical current and high-temperature exposure is investigated.Isothermal thermogravimetric analysis was employed to quantify oxidation kinetics,complemented by microstructural characterization using X-ray diffraction,scanning electron microscopy with energy-dispersive spectroscopy and transmission electron microscopy.Experimental results demonstrate that the applied current dramatically enhances oxidation rates,increasing specific mass gain from 0.25 mg/cm^(2)(0 A/cm^(2))to 5.20 mg/cm^(2)(0.2 A/cm^(2))and oxide scale thickness from 1.87 to 15.62μm after 200 h.This acceleration originates from current-induced electromigration forces that promote cationic transport through the oxide layer.The quantitative relationships between current density and oxidation parameters are established,enabling predictive modeling of interconnector degradation in solid oxide fuel cell(SOFC)systems.展开更多
Exercise produces a decrease in pain sensitivity via an effect called exercise-induced hypoalgesia(EIH).Transcranial direct current stimulation(tDCS),acting on similar analgesic mechanisms as EIH,represents a potentia...Exercise produces a decrease in pain sensitivity via an effect called exercise-induced hypoalgesia(EIH).Transcranial direct current stimulation(tDCS),acting on similar analgesic mechanisms as EIH,represents a potential complementary intervention that may amplify the effects of exercise on pain.This study aimed to explore if anodal tDCS could enhance the effect of exercise on pain compared to exercise alone.A total of 35 healthy participants aged 19–37 years completed a familiarisation session followed by two separate sessions where active and sham tDCS was applied in a randomised cross-over design.The familiarisation session involved familiarisation to the pain assessment and exercise tasks,while the subsequent tDCS sessions involved pain sensitivity assessment,exercise and either anodal tDCS or sham tDCS.tDCS doses were applied at 2 mA over the primary motor cortex for 10 min,with the reference electrode placed over the contralateral supraorbital area.The exercise task involved a sustained isometric grip strength contraction at 35%of maximal voluntary contraction(MVC)until volitional exhaustion.Pain sensitivity was evaluated as pressure pain threshold before tDCS,after tDCS,and after exercise.Across both tDCS conditions,pain threshold was higher after exercise when compared to pre-and post-tDCS measurement.This increase in pain threshold did not differ between active and sham tDCS conditions.Our findings suggest that the hypoalgesic effects of active anodal tDCS over the motor cortex prior to exercise are no greater than the effects of sham tDCS prior to exercise.展开更多
To address the issues of high costs and low component utilization caused by the independent configuration of hybrid DC circuit breakers(HCBs)and DC power flow controllers(DCPFCs)at each port in existing DC distributio...To address the issues of high costs and low component utilization caused by the independent configuration of hybrid DC circuit breakers(HCBs)and DC power flow controllers(DCPFCs)at each port in existing DC distribution networks,this paper adopts a component sharing mechanism to propose a composite multi-port hybrid DC circuit breaker(CM-HCB)with DC power flow and fault current limitation abilities,as well as reduced component costs.The proposed CM-HCB topology enables the sharing of the main breaker branch(MB)and the energy dissipation branch,while the load commutation switches(LCSs)in the main branch are reused as power flow control components,enabling flexible regulation of power flow in multiple lines.Meanwhile,by reconstructing the current path during the fault process,the proposed CM-HCB can utilize the internal coupled inductor to limit the current rise rate at the initial stage of the fault,significantly reducing the requirement for breaking current.A detailed study on the topological structure,steady-state power flow regulation mechanism,transient fault isolation mechanism,control strategy and characteristic analysis of the proposed CM-HCB is presented.Then,a Matlab/Simulink-based meshed three-terminal DC grid simulation platform with the proposed CM-HCB is built.The results indicate that the proposed CM-HCB can not only achieve flexible power flow control during steady-state operation,but also obtain current rise limitation and fault isolation abilities under short-circuit fault conditions,verifying its correctness and effectiveness.Finally,a comparative economic analysis is conducted between the proposed CM-HCB and the other two existing solutions,confirming that its component sharing mechanism can significantly reduce the number of components,lower system costs,and improve component utilization.展开更多
The influence of the cathode work function,carriers mobilities and temperature on the short-circuit current of single layer organic solar cells with Schottkey contacts was numerically studied,and the quantitative depe...The influence of the cathode work function,carriers mobilities and temperature on the short-circuit current of single layer organic solar cells with Schottkey contacts was numerically studied,and the quantitative dependences of the short-circuit current on these quantities were obtained.The results provide the theoretical foundation for experimental study of single layer organic solar cells with Schottkey contacts.展开更多
The impact of the optical band gap（Eg） of a p-type hydrogenated nanocrystalline silicon layer on the short-circuit current density（Jsc） of a thin-film silicon solar cell is assessed. We have found that the Jsc rea...The impact of the optical band gap（Eg） of a p-type hydrogenated nanocrystalline silicon layer on the short-circuit current density（Jsc） of a thin-film silicon solar cell is assessed. We have found that the Jsc reaches maximum when the Eg reaches optimum. The reason for the Jsc on Eg needs to be clarified. Our results exhibit that maximum Jsc is the balance between dark current and photocurrent. We show here that this dark current results from the density of defects in the p-layer and the barrier at the interface between p-and i-layers. An optimum cell can be designed by optimizing the p-layer via reducing the density of defects in the p-layer and the barrier at the p/i interface. Finally, a 6.6% increase in Jsc was obtained at optimum Eg for n-i-p solar cells.展开更多
A hybrid energy transmission pipeline is proposed with the aim of long-distance cooperative transmission of electricity and chemical fuels, which is composed of an inner high-temperature superconducting (HTS) power ca...A hybrid energy transmission pipeline is proposed with the aim of long-distance cooperative transmission of electricity and chemical fuels, which is composed of an inner high-temperature superconducting (HTS) power cable and outer liquefied natural gas (LNG) pipeline. The flowing LNG could maintain the operating temperature of the inner HTS power cable within the range of 85 K-90 K, thus the Bi-2223 superconductors in the HTS power cable produce little Joule loss with the transmission current below the critical current. Owing to the advantages of high power density, low transmission losses and economical manufacturing costs, the hybrid energy transmission pipeline is expected to be widely utilized in the near future. In order to ensure the safety of the HTS power cable and explosive LNG in case of short-circuit faults, this paper tests and analyzes the characteristics of Bi-2223 HTS tapes of the Type HT-CA, Type HT-SS and Type H models under short-circuit current impacts at the LNG cooling temperature (85 K-90 K). An experimental platform is designed and established for the ampacity tests of HTS tapes above LN2 cooling temperature (77 K). The AC over-current impact tests at 85 K-90 K are carried out on each sample of Bi-2223 tapes respectively, and the experimental results are analyzed and compared to evaluate their performances under different operating conditions. The results indicate that the Type HT-CA tape can withstand 50 Hz short-circuit current impact with the amplitude of 1108 A (10 times of critical current Ic ) for 100 ms at 90 K, and its resistance is the smallest of the three tested samples under similar current impacts. Therefore, the Type HT-CA Bi-2223 tape is the optimal superconductor of the HTS power cable in the hybrid energy transmission pipeline.展开更多
Aim at improving the stability of the Short-circuiting Gas Metal Arc Welding （GMAW-S） process for the enhanced speed usage, effects of current waveform parameters during short-term on the welding stability have been...Aim at improving the stability of the Short-circuiting Gas Metal Arc Welding （GMAW-S） process for the enhanced speed usage, effects of current waveform parameters during short-term on the welding stability have been investigated by experimental method. The welding power source used for the research is an inverter with a special current waveform control. It is shown that the spatter decreases at first then increases with each increase of the low current period, current increase rate and the maximum current limit. The test results are provided for welding of 1 mm and 3 mm mild steel at speed of 1.2 m/min. The stable GMA W-S process under high speed welding condition has been achieved by optimizing the parameters.展开更多
基金supported by State Key Laboratory of Power Transmission Equipment and System Security(No.2007DA10512711102,No.2007DA10512709202)Program of Introducing Talents of Discipline to Universities("111"Program)(No.B08036)the Fundamental Research Funds for the Central Universities(No.CDJXS11150026)
文摘Large-scale doubly-fed induction generator(DFIG)wind turbines are connected to the grid and required to remain grid-connection during faults,the short-circuit current contributed by the generation has become a significant issue.However,the traditional calculation methods aiming at synchronous generators cannot be directly applied to the DFIG wind turbines.A new method is needed to calculate the short-circuit current required by the planning,protection and control of the power grid.The short-circuit transition of DFIG under symmetrical and asymmetric short-circuit conditions are mathematically deduced,and the short-circuit characteristics of DFIG are analyzed.A new method is proposed to calculate the steady-state short-circuit current of DFIG based on the derived expressions.The time-domain simulations are conducted to verify the accuracy of the proposed method.
基金funded by the National Natural Science Foundation of China(52077004)Anhui Electric Power Company of the State Grid(52120021N00L).
文摘Aiming at the problemthat the traditional short-circuit current calculationmethod is not applicable to Distributed Generation(DG)accessing the distribution network,the paper proposes a short-circuit current partitioning calculation method considering the degree of voltage drop at the grid-connected point of DG.Firstly,the output characteristics of DG in the process of low voltage ride through are analyzed,and the equivalent output model of DG in the fault state is obtained.Secondly,by studying the network voltage distribution law after fault in distribution networks under different DG penetration rates,the degree of voltage drop at the grid-connected point of DG is used as a partition index to partition the distribution network.Then,iterative computation is performed within each partition,and data are transferred between partitions through split nodes to realize the fast partition calculation of short-circuit current for high proportion DG access to distribution network,which solves the problems of long iteration time and large calculation error of traditional short-circuit current.Finally,a 62-node real distribution network model containing a high proportion of DG access is constructed onMATLAB/Simulink,and the simulation verifies the effectiveness of the short-circuit current partitioning calculation method proposed in the paper,and its calculation speed is improved by 48.35%compared with the global iteration method.
基金supported by the Power Generation & Electricity Delivery of the Korea Institute of Energy Technology and Planning(KETEP)grant funded by the Korea Government Ministry of Knowledge Economy(No.2009T100200067)
文摘To study the effects of wind generators on distribution system protection,the short-circuit current(SCC) characteristics of wind generators is important.Although there are many researches on the issue,a clear agreement has not been reached so far.The SCC characteristics for different wind generators are studied.PSCAD simulation is performed in the same system integrated with different kinds of wind generators,and their results are compared with those reported in IEEE papers.The detection possibility by overcurrent relay(OCR)is discussed based on the simulation results.
文摘With the rapid development of economy, strengthen the continuous construction of national infrastructure, etc., many industry demand for steel, steel enterprise capacity expands, at the same time, the steel enterprises to positive response to the call of national energy conservation and emission reduction, using plant waste heat green development is the only way to realize the transformation and upgrading of the steel industry. This paper will be mainly for the domestic steel enterprise 6kV system short circuit current exceeds the limit and take the restrictive measures for detailed analysis and discussion for the industry reference.
基金funded by State Grid Corporation of China,grant number DQ30DK24001L。
文摘When the converter bus voltage of a voltage source converter-based high voltage direct current(VSC-HVDC)system drops below a certain predetermined threshold,the system enters low-voltage ride-through(LVRT)mode to avoid overcurrent and potential equipment failure,during which it operates as a controlled current source.The influence mechanism of LVRT control strategies on short-circuit current and overall system stability remains not yet fully and systematically investigated.First,this paper provides an overview of several LVRT strategies for VSC-HVDC systems and examines their effects on short-circuit current contribution.Next,it analyzes in detail the mechanisms through which active and reactive currents injected during LVRT impact system frequency stability,voltage stability,and synchronization stability.To address these interrelated issues,an optimized and comprehensive LVRT strategy incorporating short-circuit current constraints is proposed.The approach determines the active current ratio based on system frequency stability requirements and dynamically adjusts the active current recovery rate via phase control of the VSC-HVDC bus.The remaining capacity is allocated to reactive current support,thereby enhancing voltage and synchronization stability while maintaining sufficient short-circuit current margin and system frequency stability.Finally,simulations conducted on the PSS/E platform,using actual grid data from a selected cross-section system,validate convincingly the effectiveness of the proposed parameter optimization strategy for VSC-HVDC low-voltage ride-through.
基金supported by the National Natural Science Foundation of China(No.51977080).
文摘With the load growth and the power grid expansion,the problem of short-circuit current(SCC)exceeding the secure limit in large-scale power grids has become more serious,which poses great challenge to the optimal secure operation.Aiming at the SCC limitations,we use multiple back-toback voltage source converter based(B2B VSC)systems to separate a large-scale AC power grid into two asynchronous power grids.A multi-objective robust optimal secure operation model of large-scale power grid with multiple B2B VSC systems considering the SCC limitation is established based on the AC power flow equations.The decision variables include the on/off states of synchronous generators,power output,terminal voltage,transmission switching,bus sectionalization,and modulation ratios of B2B VSC systems.The influence of inner current sources of renewable energy generators on the system SCC is also considered.To improve the computational efficiency,a mixedinteger convex programming(MICP)framework based on convex relaxation methods including the inscribed N-sided approximation for the nonlinear SCC limitation constraints is proposed.Moreover,combined with the column-and-constraint generation(C&CG)algorithm,a method to directly solve the compromise optimal solution(COS)of the multi-objective robust optimal secure operation model is proposed.Finally,the effectiveness and computational efficiency of the proposed solution method is demonstrated by an actual 4407-bus provincial power grid and the modified IEEE 39-bus power grid,which can reduce the consumed CPU time of solving the COS by more than 90%and obtain a better COS.
基金National Key Research and Development Program of China(2021YFB3700801)。
文摘Low-density short-duration pulsed current-assisted aging treatment was applied to the Ti-6Al-4V-0.5Mo-0.5Zr alloy subjected to different solution treatments.The results show that numerous α_(p) phases redissolve into the new β phase during the pulsed current-assisted aging process,and then the newly formed β phase is mainly transformed into the β_(t) phase,with occasional transition to new α_(p) phase,leading to a remarkable grain refinement,especially for the lamellarαs phases.In comparison to conventional aging treatment,the pulsed current-assisted aging approach achieves a significant enhancement in strength without degrading ductility,yielding an excellent mechanical property combination:a yield strength of 932 MPa,a tensile strength of 1042 MPa,and an elongation of 12.2%.It is primarily ascribed to the increased fraction of β_(t) phases,the obvious grain refinement effect,and the slip block effect induced by the multiple-variantαs colonies distributed within β_(t) phases.
基金Supported by the Fundamental Research Funds for the Central Universities(2024ZYGXZR047)the National Natural Science Foundation of China(62373156)the Guangdong Basic and Applied Basic Research Foundation(2024A1515011736)。
文摘This article investigates the robust current tracking control problem of three-phase grid-connected inverters with LCL filter under external disturbance by a dynamic state feedback control method.First,this paper constructs an internal model to learn the information of the states and input of the grid-connected inverter under steady state.Second,by utilizing the internal model principle,the paper turns the tracking control problem into the robust stabilization control problem based on some appropriate coordinate transformations.Then,The paper designs a dynamics state feedback control law to deal with this robust stabilization problem,and thus the solution of the robust current tracking control problem of three-phase grid-connected inverters can be obtained.This control method can ensure the asymptotic stability of the closedloop system.Finally,the paper illustrates the effectiveness of the proposed control approach through several groups of simulations,and compares it with the feedforward control method to verify the robustness of the proposed control method to uncertain parameters.
基金supported in part by the Anhui Provincial Natural Science Foundation Youth Project(Category C)under Grant No.2508085QE184the Opening Project of Key Laboratory of Power Electronics and Motion Control of Anhui Higher Education Institutions under Grant No.PEMC24004+1 种基金the Anhui University of Technology Young Teachers Research Fund under Grant No.QZ202412the Scientific Research Startup Fund for Introduced Talents of Anhui University of Technology under Grant No.QD202340.
文摘In this paper,a comprehensive evaluation on the silicon/silicon carbide(Si/SiC)hybrid switch is performed through experimental tests in terms of both electrical performance and robustness under extreme stresses.Based on the optional turn-on and turn-off delay times under the efficiency control mode obtained from the double-pulse test(DPT),both nondestructive and destructive single-pulse avalanche tests are conducted on the Si/SiC hybrid switch as well as on the two discrete device branches inside the hybrid switch.In addition,the avalanche voltage,critical avalanche energy,and peak avalanche current,which intrinsically characterize the unclamped-inductive-switching(UIS)avalanche characteristics,are carefully examined.In this way,the physical factors dominating the UIS characteristics of the hybrid switch,thus limiting its single-pulse avalanche withstand capability,are specifically and comprehensively identified;the underlying physical mechanisms are analyzed and revealed in depth,and how the gate control sequence affects the UIS characteristics of the hybrid switch is extensively investigated.We additionally carry out short-circuit(SC)tests under the fault-under-load(FUL)condition and perform a parallel in-depth analysis to experimentally determine which branch dominates the SC withstand capability of the hybrid switch.Our experimental study indicates that,for both SC robustness and single-pulse avalanche capability,the limiting factor is a single device branch among the two parallel discrete devices,and the UIS behavior is sensitive to the variation of the gate turn-off delay time Toff_delay.The study conducted in this paper not only provides deep academic insights into the electrical performance and reliability of the Si/SiC hybrid switch,but also offers fundamental theoretical principles and technical evidence to support its more efficient and long-term reliable applications of the hybrid switch in the industrial fields.
基金financial support from the Helmholtz Association and the German Federal Ministry of Education and Research(BMBF)within the ExcellBattUlm project(03XP0257D)the HighSafe-3 project(03XP0568A)。
文摘Energy density and safety are two crucial parameters when evaluating lithium-metal batteries(LMBs).Herein,we present an ultralight polymer-based current collector,incorporating flame-retardant materials,designed specifically for thin lithium-metal anodes.Compared to the traditional copper current collector(8.96 mg cm^(-2),10μm thick),the polymer-based current collector(12μm thick)has a significantly lower areal density of 1.41 mg cm^(-2),i.e.,only one-sixth of the copper collector,thus enabling substantially higher energy densities.Accordingly,when employed in Li||NMC_(622)full-cells,the polymer-based current collector enables a specific energy of 449 Wh kg^(-1),representing a notable improvement of about14.5%compared to cells employing a classic copper current collector.The inclusion of Al(OH)_(3) as a flame retardant into the current collector suppresses flammability and,thereby,significantly improves the safety of the resulting LMBs.
文摘With the advent of the big data era,modern statistics has enjoyed unprecedented development opportunities and also faced numerous new challenges.Traditional statistical computing methods are often limited by issues such as computer memory capacity and distributed storage of data across different locations,and are unable to directly apply to large-scale data sets.Therefore,in the context of big data,designing efficient and theoretically guaranteed statistical learning and inference algorithms has become a key issue that the current field of statistics urgently needs to address.In this paper,the application status of statistical analysis methods in the big data environment was systematically reviewed,and its future development directions were analyzed to provide reference and support for the further development of theory and methods of the statistical analysis of big data.
基金supported by the National Natural Science Foundation of China(grant numbers 52071225,22179143,and 22002176)the European Union’s Horizon Europe research and innovation program Electron Beam Emergent Additive Manufacturing(EBEAM)(grant number 101087143)+2 种基金a Norway Grant through the National Science Centre(project number 2019/34/H/ST8/00547)the National Key R&D Program of China(grant number 2021YFB3800300)the Jiangsu Funding Program for Excellent Postdoctoral Talent。
文摘Lithium metal batteries(LMBs)are promising candidates for next-generation high-energy-density storage devices.However,an unstable lithium metal anode poses significant issues that critically compromise battery safety and cycle life,including lithium dendrite formation,solid electrolyte interphase degradation,dead lithium accumulation,and substantial volume fluctuations during cycling.These problems can be addressed by regulating lithium deposition and suppressing side reactions through the modification of copper current collectors using three classes of materials:metal and metal oxide,carbon,and polymer materials.This review comprehensively examines recent advances in the application of these materials as current collector coatings.Particularly,their distinct roles in the lithium deposition process are analyzed to understand how they mitigate the issues associated with the lithium metal anode.Furthermore,their inherent limitations are considered to inform future research directions.While each class of materials offers specific advantages,multifunctionality is required to effectively regulate lithium deposition.In prospect,a novel composite copper current collector design that integrates the merits of the aforementioned advanced materials is proposed.The insights from this review provide valuable guidance for the rational design of modified copper current collectors,which would significantly improve the safety and cycle life of LMBs and advance their commercialization.
文摘Transcranial direct current stimulation(tDCS)is a non-invasive technique that modifies cortical excitability and induces neuroplasticity using low-intensity electrical currents.Nuclear medicine technologies like positron emission tomography(PET)and single-photon emission computed tomography(SPECT)can quantify cerebral metabolism and other dynamics.Evidence suggests that combining tDCS with these imaging methods enhances understanding and outcomes for neurological and psychiatric conditions.This review highlights how nuclear medicine can objectively characterize tDCS eff ects,map network modulation,and identify predictive biomarkers.PET and SPECT indicate changes in glucose metabolism and neurotransmitter activity post-tDCS,demonstrating their value in validation.While the co-application of these methodologies is still in conceptual stages,their integration may advance precision neuromodulation and inform rehabilitation strategies.
基金supported by Natural Science Foundation of Wuhan(2024040701010051)Natural Science Foundation of Hubei(2023AFB111)and National Natural Science Foundation of China(52401108).
文摘To elucidate the accelerated degradation mechanisms of metallic interconnects in operational solid oxide fuel cells,the oxidation behavior of FSS430 ferritic stainless steel under the coupling of simultaneous electrical current and high-temperature exposure is investigated.Isothermal thermogravimetric analysis was employed to quantify oxidation kinetics,complemented by microstructural characterization using X-ray diffraction,scanning electron microscopy with energy-dispersive spectroscopy and transmission electron microscopy.Experimental results demonstrate that the applied current dramatically enhances oxidation rates,increasing specific mass gain from 0.25 mg/cm^(2)(0 A/cm^(2))to 5.20 mg/cm^(2)(0.2 A/cm^(2))and oxide scale thickness from 1.87 to 15.62μm after 200 h.This acceleration originates from current-induced electromigration forces that promote cationic transport through the oxide layer.The quantitative relationships between current density and oxidation parameters are established,enabling predictive modeling of interconnector degradation in solid oxide fuel cell(SOFC)systems.
文摘Exercise produces a decrease in pain sensitivity via an effect called exercise-induced hypoalgesia(EIH).Transcranial direct current stimulation(tDCS),acting on similar analgesic mechanisms as EIH,represents a potential complementary intervention that may amplify the effects of exercise on pain.This study aimed to explore if anodal tDCS could enhance the effect of exercise on pain compared to exercise alone.A total of 35 healthy participants aged 19–37 years completed a familiarisation session followed by two separate sessions where active and sham tDCS was applied in a randomised cross-over design.The familiarisation session involved familiarisation to the pain assessment and exercise tasks,while the subsequent tDCS sessions involved pain sensitivity assessment,exercise and either anodal tDCS or sham tDCS.tDCS doses were applied at 2 mA over the primary motor cortex for 10 min,with the reference electrode placed over the contralateral supraorbital area.The exercise task involved a sustained isometric grip strength contraction at 35%of maximal voluntary contraction(MVC)until volitional exhaustion.Pain sensitivity was evaluated as pressure pain threshold before tDCS,after tDCS,and after exercise.Across both tDCS conditions,pain threshold was higher after exercise when compared to pre-and post-tDCS measurement.This increase in pain threshold did not differ between active and sham tDCS conditions.Our findings suggest that the hypoalgesic effects of active anodal tDCS over the motor cortex prior to exercise are no greater than the effects of sham tDCS prior to exercise.
基金funded by Youth Talent Growth Project of Guizhou Provincial Department of Education(No.Qianjiaoji[2024]21)National Natural Science Foundation of China(No.62461008 and No.52507211)Guizhou Provincial Key Technology R&D Program(No.[2024]General 049).
文摘To address the issues of high costs and low component utilization caused by the independent configuration of hybrid DC circuit breakers(HCBs)and DC power flow controllers(DCPFCs)at each port in existing DC distribution networks,this paper adopts a component sharing mechanism to propose a composite multi-port hybrid DC circuit breaker(CM-HCB)with DC power flow and fault current limitation abilities,as well as reduced component costs.The proposed CM-HCB topology enables the sharing of the main breaker branch(MB)and the energy dissipation branch,while the load commutation switches(LCSs)in the main branch are reused as power flow control components,enabling flexible regulation of power flow in multiple lines.Meanwhile,by reconstructing the current path during the fault process,the proposed CM-HCB can utilize the internal coupled inductor to limit the current rise rate at the initial stage of the fault,significantly reducing the requirement for breaking current.A detailed study on the topological structure,steady-state power flow regulation mechanism,transient fault isolation mechanism,control strategy and characteristic analysis of the proposed CM-HCB is presented.Then,a Matlab/Simulink-based meshed three-terminal DC grid simulation platform with the proposed CM-HCB is built.The results indicate that the proposed CM-HCB can not only achieve flexible power flow control during steady-state operation,but also obtain current rise limitation and fault isolation abilities under short-circuit fault conditions,verifying its correctness and effectiveness.Finally,a comparative economic analysis is conducted between the proposed CM-HCB and the other two existing solutions,confirming that its component sharing mechanism can significantly reduce the number of components,lower system costs,and improve component utilization.
文摘The influence of the cathode work function,carriers mobilities and temperature on the short-circuit current of single layer organic solar cells with Schottkey contacts was numerically studied,and the quantitative dependences of the short-circuit current on these quantities were obtained.The results provide the theoretical foundation for experimental study of single layer organic solar cells with Schottkey contacts.
基金Project partly supported by the National High Technology Research and Development Program of China(No.2011AA050504)
文摘The impact of the optical band gap（Eg） of a p-type hydrogenated nanocrystalline silicon layer on the short-circuit current density（Jsc） of a thin-film silicon solar cell is assessed. We have found that the Jsc reaches maximum when the Eg reaches optimum. The reason for the Jsc on Eg needs to be clarified. Our results exhibit that maximum Jsc is the balance between dark current and photocurrent. We show here that this dark current results from the density of defects in the p-layer and the barrier at the interface between p-and i-layers. An optimum cell can be designed by optimizing the p-layer via reducing the density of defects in the p-layer and the barrier at the p/i interface. Finally, a 6.6% increase in Jsc was obtained at optimum Eg for n-i-p solar cells.
基金supported by National Key R&D Project under Grant(2018YFB0904400).
文摘A hybrid energy transmission pipeline is proposed with the aim of long-distance cooperative transmission of electricity and chemical fuels, which is composed of an inner high-temperature superconducting (HTS) power cable and outer liquefied natural gas (LNG) pipeline. The flowing LNG could maintain the operating temperature of the inner HTS power cable within the range of 85 K-90 K, thus the Bi-2223 superconductors in the HTS power cable produce little Joule loss with the transmission current below the critical current. Owing to the advantages of high power density, low transmission losses and economical manufacturing costs, the hybrid energy transmission pipeline is expected to be widely utilized in the near future. In order to ensure the safety of the HTS power cable and explosive LNG in case of short-circuit faults, this paper tests and analyzes the characteristics of Bi-2223 HTS tapes of the Type HT-CA, Type HT-SS and Type H models under short-circuit current impacts at the LNG cooling temperature (85 K-90 K). An experimental platform is designed and established for the ampacity tests of HTS tapes above LN2 cooling temperature (77 K). The AC over-current impact tests at 85 K-90 K are carried out on each sample of Bi-2223 tapes respectively, and the experimental results are analyzed and compared to evaluate their performances under different operating conditions. The results indicate that the Type HT-CA tape can withstand 50 Hz short-circuit current impact with the amplitude of 1108 A (10 times of critical current Ic ) for 100 ms at 90 K, and its resistance is the smallest of the three tested samples under similar current impacts. Therefore, the Type HT-CA Bi-2223 tape is the optimal superconductor of the HTS power cable in the hybrid energy transmission pipeline.
文摘Aim at improving the stability of the Short-circuiting Gas Metal Arc Welding （GMAW-S） process for the enhanced speed usage, effects of current waveform parameters during short-term on the welding stability have been investigated by experimental method. The welding power source used for the research is an inverter with a special current waveform control. It is shown that the spatter decreases at first then increases with each increase of the low current period, current increase rate and the maximum current limit. The test results are provided for welding of 1 mm and 3 mm mild steel at speed of 1.2 m/min. The stable GMA W-S process under high speed welding condition has been achieved by optimizing the parameters.
