Tensile properties of a new α＋Ti2Cu alloy after solid forging at 950 °C and semi-solid forging at 1 000 °C and 1 050 °C were investigated over the temperature range of 20-600 °C. The results reve...Tensile properties of a new α＋Ti2Cu alloy after solid forging at 950 °C and semi-solid forging at 1 000 °C and 1 050 °C were investigated over the temperature range of 20-600 °C. The results reveal that high strength and low ductility are obtained in all semi-solid forged alloys. Tensile properties decrease as the semi-solid forging temperature increases, and cleavage fractures are observed after semi-solid forging at 1 050 °C. The variations in tensile properties are attributed to the coarse microstructures obtained in the semi-solid alloys. It is found that the elevated semi-solid temperatures lead to more liquid precipitates along the prior grain boundaries, which increases the peritectic precipitation and formation of Ti2Cu precipitation zones during re-solidification. Recrystallization heat treatment leads to fine microstructure of semi-solid forged alloys, resulting in improvement of tensile properties.展开更多
The very latest technique for impeller manufacture is called semi-solid moulding(SSM).Cummins Turbo Technologies Limited,together with Aluminum Complex Components Inc,developed SSM compressor wheels as a way of achiev...The very latest technique for impeller manufacture is called semi-solid moulding(SSM).Cummins Turbo Technologies Limited,together with Aluminum Complex Components Inc,developed SSM compressor wheels as a way of achieving cost and durability performance somewhere between that of cast and machined from solid(MFS) aluminium alloy wheels.Experimental results show SSM material has a superior microstructure and mechanical properties over cast and comparable to MFS materials.Component testing including durability testing,using accelerated speed cycle tests,proves SSM compressor wheels emerge as being significantly more durable than cast equivalents and approaching that of MFS impellers.Further challenges for semi-solid processing in manufacture of other complex components and other materials in automotive industry in terms of both cost and durability are also discussed.展开更多
The differences in damage values,residual stresses,microstructure and mechanical properties of Ti–6Al–4V alloy under hammer forging and press forging were explored through physical experiments and numerical simulati...The differences in damage values,residual stresses,microstructure and mechanical properties of Ti–6Al–4V alloy under hammer forging and press forging were explored through physical experiments and numerical simulations.The results showed that the temperature field and equivalent strain field of forgings under the hammer forging process were more uniformly distributed,resulting in smaller surface cracks and better residual stress distribution.The impact dynamic loading of hammer forging leads to forgings with higher dislocation densities,while the stabilized strain rate of press forging results in forgings exhibiting finer grain sizes.In this context,the yield strength enhancement of forgings by both processes was nearly identical,while the forgings demonstrated more excellent elongation under the hammer forging process.Additionally,increasing the number of blows in the hammer forging process or enhancing the loading rate in the press forging process can optimize the residual stress distribution of the forgings while simultaneously promoting dislocation multiplication and grain refinement.展开更多
Magnesium alloy thin-walled cylindrical components with the advantages of high specific stiffness and strength present broad prospect for the lightweight of aerospace components.However,poor formability resulting from...Magnesium alloy thin-walled cylindrical components with the advantages of high specific stiffness and strength present broad prospect for the lightweight of aerospace components.However,poor formability resulting from the hexagonal close-packed crystal structure in magnesium alloy puts forwards a great challenge for thin-walled cylindrical components fabrication,especially for extreme structure with the thicknesschanging web and the high thin-wall.In this research,an ZK61 magnesium alloy thin-walled cylindrical component was successfully fabricated by two-step forging,i.e.,the pre-forging and final-forging is mainly used for wed and thin-wall formation,respectively.Microstructure and mechanical properties at the core,middle and margin of the web and the thin-wall of the pre-forged and final-forged components are studied in detail.Due to the large strain-effectiveness and metal flow along the radial direction(RD),the grains of the web are all elongated along RD for the pre-forged component,where an increasingly elongated trend is found from the core to the margin of the wed.A relatively low recrystallized degree occurs during pre-forging,and the web at different positions are all with prismatic and pyramid textures.During finalforging,the microstructures of the web and the thin-wall are almost equiaxed due to the remarkable occurrence of dynamic recrystallization.Similarity,except for few basal texture of the thin-wall,only prismatic and pyramid textures are found for the final-forged component.Compared with the initial billet,an obviously improved mechanical isotropy is achieved during pre-forging,which is well-maintained during final-forging.展开更多
Digital modeling and autonomous control of the die forging process are significant challenges in realizing high-quality intelli-gent forging of components.Using the die forging of AA2014 aluminum alloy as a case study...Digital modeling and autonomous control of the die forging process are significant challenges in realizing high-quality intelli-gent forging of components.Using the die forging of AA2014 aluminum alloy as a case study,a machine-learning-assisted method for di-gital modeling of the forging force and autonomous control in response to forging parameter disturbances was proposed.First,finite ele-ment simulations of the forging processes were conducted under varying friction factors,die temperatures,billet temperatures,and for-ging velocities,and the sample data,including process parameters and forging force under different forging strokes,were gathered.Pre-diction models for the forging force were established using the support vector regression algorithm.The prediction error of F_(f),that is,the forging force required to fill the die cavity fully,was as low as 4.1%.To further improve the prediction accuracy of the model for the ac-tual F_(f),two rounds of iterative forging experiments were conducted using the Bayesian optimization algorithm,and the prediction error of F_(f) in the forging experiments was reduced from 6.0%to 1.5%.Finally,the prediction model of F_(f) combined with a genetic algorithm was used to establish an autonomous optimization strategy for the forging velocity at each stage of the forging stroke,when the billet and die temperatures were disturbed,which realized the autonomous control in response to disturbances.In cases of−20 or−40℃ reductions in the die and billet temperatures,forging experiments conducted with the autonomous optimization strategy maintained the measured F_(f) around the target value of 180 t,with the relative error ranging from−1.3%to+3.1%.This work provides a reference for the study of di-gital modeling and autonomous optimization control of quality factors in the forging process.展开更多
The mechanical properties,microstructure and second phase precipitation behavior of flange forgings for high-pressure hydrogen storage vessels at different tempering temperatures(620–700℃)were studied.The results sh...The mechanical properties,microstructure and second phase precipitation behavior of flange forgings for high-pressure hydrogen storage vessels at different tempering temperatures(620–700℃)were studied.The results showed that when tempered at 620–680°C,the main microstructure of the test steel was tempered sorbite,and the main microstructure of tempered steel changed to martensite at 700℃.At 700℃,the dislocation density increased and some retained austenite existed.With the tempering temperature increasing,the yield strength showed a decreasing trend,the formation of fresh martensite made the tensile strength first decrease and then increase slightly,the impact energy at−40℃increased first and then decreased,and the impact energy at 660℃had the maximum value.The precipitates of MC type were mainly(Mo,V,Ti)C.The test steel had excellent strength and toughness matching at 660℃tempering,the tensile strength at different cross section locations was above 750 MPa,the impact energy was above 200 J at−40℃,and the relative percentage reduction of area(ZH2/ZN2)was above 75%at hydrogen environment of 6.3 MPa.展开更多
This study systematically investigated the microstructure,mechanical properties,and corrosion behavior of an extruded Zn-0.2Mg alloy processed by multi-directional forging(MDF)at 100℃.The mean grain size was remarkab...This study systematically investigated the microstructure,mechanical properties,and corrosion behavior of an extruded Zn-0.2Mg alloy processed by multi-directional forging(MDF)at 100℃.The mean grain size was remarkably decreased from 17.2±0.5µm to 1.9±0.3µm,and 84.4%of the microstructure was occupied by grains of below 1µm in size after applying three MDF passes.Electron backscattered difraction examinations revealed that continuous dynamic recrystallization,progressive lattice rotation,and particle-stimulated nucleation mechanisms were recognized as contributing to microstructural evolution.Furthermore,transmission electron microscopy results showed that nanoparticles of Mg/Zn dynamically formed under high strain MDF,while the initial extrusion fber texture was altered to be<0001>parallel to the fnal forging axis.A synergistic efect of grain refnement,texture evolution,second-phase precipitates,and dislocation strengthening resulted in an increased ultimate tensile strength of 232±5 MPa after three MDF passes.However,this was accompanied by a reduction in the elongation(8±2.1%).Additionally,a high corrosion rate of 0.59 mm/year was measured for the experimental alloy fabricated by 3 MDF passes.In agreement with the latter,electrochemical impedance spectroscopy results indicated that the grain refnement improved the passivation kinetics of the oxide layer.展开更多
This study investigates the differences in microstructural control between cryogenic forging combined with pre-deformation(PCF)and traditional thermal forging(TTF)for 7050 aluminum forgings intended for aerospace appl...This study investigates the differences in microstructural control between cryogenic forging combined with pre-deformation(PCF)and traditional thermal forging(TTF)for 7050 aluminum forgings intended for aerospace applications.The PCF process,utilizing cryogenic deformation,significantly refines the coarse grains at the surface of the forgings,resulting in a finer and more uniform microstructure,thereby effectively addressing the issue of surface coarse grains associated with traditional methods.The findings indicate that the PCF process can accumulate higher stored energy,facilitating static recrystallization(SRX)during subsequent heat treatment and enhancing the microstructural uniformity.Utilizing various analytical techniques,including optical microscopy(OM),electron backscatter diffraction(EBSD),and transmission electron microscopy(TEM).This study reveals the superiority of the PCF process in terms of strain accumulation,dislocation density,and grain refinement.In conclusion,this method offers advantages in enhancing the performance and microstructural uniformity of 7050 aluminum forgings,presenting new opportunities for applications in the aluminum forging industry.展开更多
Laser-directed energy deposition(LDED)technology has demonstrated great potential for the rapid and integrated fabrication of nickel-based superalloy components.The plastic deformation-assisted method is crucial for a...Laser-directed energy deposition(LDED)technology has demonstrated great potential for the rapid and integrated fabrication of nickel-based superalloy components.The plastic deformation-assisted method is crucial for achieving grain refinement and microstructural homogeneity in LDED-fabricated superalloys.However,existing methods suffer from uniformity constraints owing to their high deformation resistance,which significantly limits their application in load-bearing components.To address these issues,a synchronous-hot-forging-assisted(SHFA)LDED additive manufacturing method was proposed,and its effects on the macroscopic morphology,microstructure,and mechanical properties of GH4169 nickel-based alloy specimens were systematically compared.The results demonstrated up to 30.1%average plastic deformation in hot-forging components while maintaining good surface flatness.The synergistic effect of dislocation accumulation and dynamic recrystallization during hot forging enables dramatic grain refinement,reducing the average grain size by 89.1%(from 168.5μm to 18.4μm)while weakening texture intensity from 15.31 to 2.15,ultimately promoting equiaxed grain formation.The pores of hot-forging components changed from fine round to flat,the porosity decreased from 0.264%to 0.089%,and the densification level was significantly improved.With the increase in the synchronous hot-forging force,the average ultimate tensile strength of hot-forging components can reach 1175.1 MPa,while the anisotropy difference is gradually weakened.The SHFA-LDED process not only achieves excellent grain refinement and microstructure homogenization but also enhances mechanical properties,providing a new technical path for the additive manufacturing of high-performance nickel-based superalloy components.展开更多
To explore ambient strengthening and high temperature ductility,a combined forming approach of multidirectional forging and asymmetric rolling was proposed.A novel multicomponent ultralight Mg-3.11Li-2.31Al-1.95Sn-0.9...To explore ambient strengthening and high temperature ductility,a combined forming approach of multidirectional forging and asymmetric rolling was proposed.A novel multicomponent ultralight Mg-3.11Li-2.31Al-1.95Sn-0.94Y-0.45Er alloy was fabricated.The microstructural evolution and mechanical properties were investigated by microstructural characterization and tensile test.The combined forming results in remarkable grain refinement.The ultimate tensile strength and elongation of(255±7)MPa and 24.9%,respectively,were obtained at room temperature.The contribution of various strengthening mechanisms of the rolled alloy was obtained.Microstructural examination revealed the occurrence of dynamic recrystallization at 473-573 K and dynamic grain growth at 573-623 K.The maximum elongation of 293.9%was demonstrated at 623 K and 5×10^(-4)s^(-1).The dominate deformation mechanism at elevated temperatures is dislocation viscous glide.展开更多
Today,I want to share how international standards can forge trust and fuel innovation,laying the foundation for a future where AI benefits everyone,everywhere.First,AI standards,developed jointly by ISO and IEC-the In...Today,I want to share how international standards can forge trust and fuel innovation,laying the foundation for a future where AI benefits everyone,everywhere.First,AI standards,developed jointly by ISO and IEC-the International Electrotechnical Commission-help build global trust and enable responsible innovation by bringing clarity and coherence to an ever-changing AI landscape.As developments in AI continue to emerge at speed,regulation is struggling to keep up and the proliferation of competing standards has created confusion rather than clarity.ISO and our partner IEC are addressing this challenge through the work of our expert committee on AI,SC 42,which takes a holistic,cohesive approach to AI standardization.展开更多
The homogenized Mg−5.6Gd−0.8Zn(wt.%)alloys were treated with water cooling and furnace cooling to obtain specimens without and with the 14H long-period stacking ordered(LPSO)phase.Subsequently,multi-directional forgin...The homogenized Mg−5.6Gd−0.8Zn(wt.%)alloys were treated with water cooling and furnace cooling to obtain specimens without and with the 14H long-period stacking ordered(LPSO)phase.Subsequently,multi-directional forging(MDF)experiments were carried out.The microstructure and mechanical properties of different regions(the center,middle and edge regions)in the MDFed alloys were systematically investigated,and the effect of LPSO phase on them was discussed.The results show that the alloys in different regions undergo significant grain refinement during the MDF process.Inhomogeneous microstructures with different degrees of dynamic recrystallization(DRX)are formed,resulting in microhardness heterogeneity.The alloy with the LPSO phase has higher microstructure homogeneity,a higher degree of recrystallization,and better comprehensive mechanical properties than the alloy without the LPSO phase.The furnace-cooled alloy after 18 passes of MDF has the best comprehensive mechanical properties,with an ultimate compressive strength of 488 MPa,yield strength of 258 MPa,and fracture strain of 21.2%.DRX behavior is closely related to the LPSO phase and deformation temperature.The kinked LPSO phase can act as a potential nucleation site for DRX grains,while the fragmented LPSO phase promotes DRX nucleation through the particle-stimulated nucleation mechanism.展开更多
In-situ TiB_(2)/Al–Cu composite was processed by multidirectional forging(MDF)for six passes.The microstructure evolution of the forged workpiece was examined across various regions.The mechanical properties of the a...In-situ TiB_(2)/Al–Cu composite was processed by multidirectional forging(MDF)for six passes.The microstructure evolution of the forged workpiece was examined across various regions.The mechanical properties of the as-cast and MDFed composites were compared,and their strengthening mechanisms were analyzed.Results indicate that the grain refinement achieved through the MDF process is mainly due to the subdivision of the original grains through mechanical geometric fragmentation and the occurrence of dynamic recrystallization(DRX).DRX grains are formed through discontinuous DRX,continuous DRX,and recrystallization induced by particle-stimulated nucleation.A rise in accumulated equivalent strain(Σ?ε)results in finerα-Al grains and a more uniform distribution of TiB_(2)particles,which enhance the Vickers hardness of the composite.In addition,the tensile properties of the MDFed composite significantly improve compared with those of the as-cast composites,with ultimate tensile strength and yield strength increasing by 51.2%and 54%,respectively.This enhancement is primarily due to grain refinement strengthening and dislocation strengthening achieved by the MDF process.展开更多
The superplasticity of the Mg−8.59Gd−3.85Y−1.14Zn−0.49Zr alloy was investigated before and after multi-directional forging(MDF)and the mechanisms affecting superplastic deformation were analyzed.The results indicate t...The superplasticity of the Mg−8.59Gd−3.85Y−1.14Zn−0.49Zr alloy was investigated before and after multi-directional forging(MDF)and the mechanisms affecting superplastic deformation were analyzed.The results indicate that after MDF at a temperature of 350℃and strain rates of 0.1 and 0.01 s^(−1)(1-MDFed and 2-MDFed),the superplasticity of the alloy can be significantly improved.The elongations of the MDFed alloys exceed 400%under the strain rate of 6.06×10^(−4)s^(−1)and temperatures of 350,375,and 400℃,and reach the maximum values of 766%(1-MDFed)and 693%(2-MDFed)at 375℃.The grain boundary sliding of the MDFed alloy is sufficient,and the energy barrier of deformation decreases.Theβphase limits the grain growth and promotes dynamic recrystallization,maintaining the stability of the fine-grained structure during superplastic deformation.Several Y-rich phases nucleate in the high-strain region(i.e.,the final fracture region)at high temperatures,accelerating the fracture of the specimen.展开更多
The semi-solid filling-plastic flowing integrated forging process of semi-solid 6061 Al alloy was simulated by commercial finite element software DEFORM-3D.Temperature,fluid and stress-strain fields were considered in...The semi-solid filling-plastic flowing integrated forging process of semi-solid 6061 Al alloy was simulated by commercial finite element software DEFORM-3D.Temperature,fluid and stress-strain fields were considered in numerical simulation.The simulation results show that the plastic deformation of billet of the ends is higher than that of billet in the straight cylinder.The value of plastic deformation varies with loading mode and plastic deformation fields at the stage of increasing pressure to constant value.When the thixoforging experiments were performed at 590 ℃,15 mm/s of punch velocity and 46 MPa of pressure side urn,it gets the filling wholly and dense internal organization of semi-solid thixoforging parts is gotten.Finite element analysis results are compatible with experimental ones.展开更多
The microstructure and mechanical properties of the Ti-5Al-5Mo-5V-1Cr-1Fe(Ti-55511)alloy under different strains were investigated through the design of step-shaped die forging.The results indicate that continuous dyn...The microstructure and mechanical properties of the Ti-5Al-5Mo-5V-1Cr-1Fe(Ti-55511)alloy under different strains were investigated through the design of step-shaped die forging.The results indicate that continuous dynamic recrystallization(CDRX)and discontinuous dynamic recrystallization(DDRX)occur in the high strain region.The orientation of the grains produced by CDRX is random and does not weaken the fiber texture.<100>-oriented grains expand gradually with increasing strain,thereby enhancing the strength of{100}texture.Significant anisotropic mechanical properties are observed in the large strain region and analyzed through in-situ tensile experiments.When the loading direction is parallel to the longitudinal(L)direction,strain concentration is observed near the dynamically recrystallized(DRXed)grains and inside grains oriented along<100>,leading to crack initiation.Furthermore,the small angle between the loading direction and the c-axis hinders the activation of prismatic and basal slip,thereby enhancing the strength.When the loading direction is parallel to the short transverse(ST)direction,cracks are initiated not only within grains oriented along<100>,but also at the grain boundaries.Regarding impact toughness,the elongatedβgrains in the L direction enhance the resistance to crack propagation.展开更多
The homogenization on microstructure and mechanical properties of 2A50 aluminum alloy prepared by liquid forging was investigated.Wheel hubs were produced using direct and compound loading.The results show that the mi...The homogenization on microstructure and mechanical properties of 2A50 aluminum alloy prepared by liquid forging was investigated.Wheel hubs were produced using direct and compound loading.The results show that the microstructure and mechanical properties are inhomogeneous in direct forged samples.The microstructure of the wall is coarser than that of the base,and the mechanical properties are lower and some defects are detected at the wheel corner.Using compound loading,the microstructure and mechanical properties of the wall are improved evidently.With increasing feeding amount,the microstructure and mechanical properties become more homogeneous.The defects disappear when the feeding amount is 4 mm.The forged wheel hubs could obtain fine and homogeneous microstructure with grain size of 20-30 μm,tensile strength of 355 MPa and elongation of 10% when the feeding amount is 10 mm.The microstructure and mechanical properties of liquid forged workpieces could be controlled and homogenized using compound loading.展开更多
The A356 aluminum alloy wheels were prepared by thixo-forging combined with a low superheat casting process. The as-cast microstructure, microstructure evolution during reheating and the mechanical properties of the t...The A356 aluminum alloy wheels were prepared by thixo-forging combined with a low superheat casting process. The as-cast microstructure, microstructure evolution during reheating and the mechanical properties of the thixo-forged A356 aluminum alloy wheels were investigated. The results show that the A356 aluminum alloy billet with fine, uniform and non-dendritic grains can be obtained when the melt is cast at 635 ℃. When the billet is reheated at 600 ℃ for 60 min, the non-dendritic grains are changed into spherical ones and the billet can be easily thixo-forged into wheels. The tensile strength and elongation of thixo-forged wheels with T6 heat treatment are 327.6 MPa and 7.8%, respectively, which are higher than those of a cast wheel. It is suggested that the thixo-forging combined with the low superheat casting process is an effective technique to produce aluminum alloy wheels with high mechanical properties.展开更多
The effect of forging passes on the refinement of high purity aluminum during multi-forging was investigated. The attention was focused on the structure uniformity due to deformation uniformity and the grain refinemen...The effect of forging passes on the refinement of high purity aluminum during multi-forging was investigated. The attention was focused on the structure uniformity due to deformation uniformity and the grain refinement limitation with very high strains. The results show that the fine grain zone in the center of sample expands gradually with the increase of forging passes. When the forging passes reach 6, an X-shape fine grain zone is initially formed. With a further increase of the passes, this X-shape zone tends to spread the whole sample. Limitation in the structural refinement is observed with increasing strains during multi-forging process at the room temperature. The grains size in the center is refined to a certain size （110 μm as forging passes reach 12, and there is no further grain refinement in the center with increasing the forging passes to 24. However, the size of the coarse grains near the surface is continuously decreased with increasing the forging passes to 24.展开更多
Microstructure and mechanical properties of AZ61 Mg alloy during isothermal multi-axial forging （MAF） were studied. The mechanisms of grain refinement and relationship between the microstructures and mechanical prop...Microstructure and mechanical properties of AZ61 Mg alloy during isothermal multi-axial forging （MAF） were studied. The mechanisms of grain refinement and relationship between the microstructures and mechanical properties were discussed. The results show that the average grain size decreases with increasing the number of MAF passes. The grains are significantly refined at the 1st and 2nd MAF passes, and gradually refined at higher MAF passes. The initial grain size of 148 lam decreases to about 14 gm after 6 MAF passes. The grain refinement occurs mainly by continuous dynamic recrystallization. With increasing the MAF passes, both the tensile strength and the elongation to failure of the alloy are significantly enhanced.展开更多
基金Projects (2005CCA06400, 2007CB613807) supported by the National Basic Research Program of ChinaProject (CHD2012JC078) supported by the Special Fund for Basic Scientific Research of Central Colleges, China+1 种基金Project (0111201) supported by the State Key Laboratory for Machanical Behavior of MaterialsProject (20110474) supported by Natural Science Basic Research Plan in Shaanxi Province of China
文摘Tensile properties of a new α＋Ti2Cu alloy after solid forging at 950 °C and semi-solid forging at 1 000 °C and 1 050 °C were investigated over the temperature range of 20-600 °C. The results reveal that high strength and low ductility are obtained in all semi-solid forged alloys. Tensile properties decrease as the semi-solid forging temperature increases, and cleavage fractures are observed after semi-solid forging at 1 050 °C. The variations in tensile properties are attributed to the coarse microstructures obtained in the semi-solid alloys. It is found that the elevated semi-solid temperatures lead to more liquid precipitates along the prior grain boundaries, which increases the peritectic precipitation and formation of Ti2Cu precipitation zones during re-solidification. Recrystallization heat treatment leads to fine microstructure of semi-solid forged alloys, resulting in improvement of tensile properties.
文摘The very latest technique for impeller manufacture is called semi-solid moulding(SSM).Cummins Turbo Technologies Limited,together with Aluminum Complex Components Inc,developed SSM compressor wheels as a way of achieving cost and durability performance somewhere between that of cast and machined from solid(MFS) aluminium alloy wheels.Experimental results show SSM material has a superior microstructure and mechanical properties over cast and comparable to MFS materials.Component testing including durability testing,using accelerated speed cycle tests,proves SSM compressor wheels emerge as being significantly more durable than cast equivalents and approaching that of MFS impellers.Further challenges for semi-solid processing in manufacture of other complex components and other materials in automotive industry in terms of both cost and durability are also discussed.
基金supported by the National Natural Science Foundation of China(Nos.52175145 and 51775427)the Key Research and Development Projects of Shaanxi Province(Grant No.2023-YBGY-335).
文摘The differences in damage values,residual stresses,microstructure and mechanical properties of Ti–6Al–4V alloy under hammer forging and press forging were explored through physical experiments and numerical simulations.The results showed that the temperature field and equivalent strain field of forgings under the hammer forging process were more uniformly distributed,resulting in smaller surface cracks and better residual stress distribution.The impact dynamic loading of hammer forging leads to forgings with higher dislocation densities,while the stabilized strain rate of press forging results in forgings exhibiting finer grain sizes.In this context,the yield strength enhancement of forgings by both processes was nearly identical,while the forgings demonstrated more excellent elongation under the hammer forging process.Additionally,increasing the number of blows in the hammer forging process or enhancing the loading rate in the press forging process can optimize the residual stress distribution of the forgings while simultaneously promoting dislocation multiplication and grain refinement.
基金supported by the National Natural Science Foundation of China(No.52405408,No.U21A20131,No.U2037204,No.52422510)the Natural Science Foundation of Hubei Province(No.2023AFB116)+1 种基金the State Key Laboratory of Materials Processing and Die&Mould TechnologyHuazhong University of Science and Technology(No.P2022-005)。
文摘Magnesium alloy thin-walled cylindrical components with the advantages of high specific stiffness and strength present broad prospect for the lightweight of aerospace components.However,poor formability resulting from the hexagonal close-packed crystal structure in magnesium alloy puts forwards a great challenge for thin-walled cylindrical components fabrication,especially for extreme structure with the thicknesschanging web and the high thin-wall.In this research,an ZK61 magnesium alloy thin-walled cylindrical component was successfully fabricated by two-step forging,i.e.,the pre-forging and final-forging is mainly used for wed and thin-wall formation,respectively.Microstructure and mechanical properties at the core,middle and margin of the web and the thin-wall of the pre-forged and final-forged components are studied in detail.Due to the large strain-effectiveness and metal flow along the radial direction(RD),the grains of the web are all elongated along RD for the pre-forged component,where an increasingly elongated trend is found from the core to the margin of the wed.A relatively low recrystallized degree occurs during pre-forging,and the web at different positions are all with prismatic and pyramid textures.During finalforging,the microstructures of the web and the thin-wall are almost equiaxed due to the remarkable occurrence of dynamic recrystallization.Similarity,except for few basal texture of the thin-wall,only prismatic and pyramid textures are found for the final-forged component.Compared with the initial billet,an obviously improved mechanical isotropy is achieved during pre-forging,which is well-maintained during final-forging.
基金financially supported by the National Key Research and Development Program of China(No.2022YFB3706901)the National Natural Science Foundation of China(No.52090041)the Young Elite Scientists Sponsorship Program by CAST(No.2022QNRC 001).
文摘Digital modeling and autonomous control of the die forging process are significant challenges in realizing high-quality intelli-gent forging of components.Using the die forging of AA2014 aluminum alloy as a case study,a machine-learning-assisted method for di-gital modeling of the forging force and autonomous control in response to forging parameter disturbances was proposed.First,finite ele-ment simulations of the forging processes were conducted under varying friction factors,die temperatures,billet temperatures,and for-ging velocities,and the sample data,including process parameters and forging force under different forging strokes,were gathered.Pre-diction models for the forging force were established using the support vector regression algorithm.The prediction error of F_(f),that is,the forging force required to fill the die cavity fully,was as low as 4.1%.To further improve the prediction accuracy of the model for the ac-tual F_(f),two rounds of iterative forging experiments were conducted using the Bayesian optimization algorithm,and the prediction error of F_(f) in the forging experiments was reduced from 6.0%to 1.5%.Finally,the prediction model of F_(f) combined with a genetic algorithm was used to establish an autonomous optimization strategy for the forging velocity at each stage of the forging stroke,when the billet and die temperatures were disturbed,which realized the autonomous control in response to disturbances.In cases of−20 or−40℃ reductions in the die and billet temperatures,forging experiments conducted with the autonomous optimization strategy maintained the measured F_(f) around the target value of 180 t,with the relative error ranging from−1.3%to+3.1%.This work provides a reference for the study of di-gital modeling and autonomous optimization control of quality factors in the forging process.
基金supported by the National Key research and Development Program of China(No.2022YFB4003001).
文摘The mechanical properties,microstructure and second phase precipitation behavior of flange forgings for high-pressure hydrogen storage vessels at different tempering temperatures(620–700℃)were studied.The results showed that when tempered at 620–680°C,the main microstructure of the test steel was tempered sorbite,and the main microstructure of tempered steel changed to martensite at 700℃.At 700℃,the dislocation density increased and some retained austenite existed.With the tempering temperature increasing,the yield strength showed a decreasing trend,the formation of fresh martensite made the tensile strength first decrease and then increase slightly,the impact energy at−40℃increased first and then decreased,and the impact energy at 660℃had the maximum value.The precipitates of MC type were mainly(Mo,V,Ti)C.The test steel had excellent strength and toughness matching at 660℃tempering,the tensile strength at different cross section locations was above 750 MPa,the impact energy was above 200 J at−40℃,and the relative percentage reduction of area(ZH2/ZN2)was above 75%at hydrogen environment of 6.3 MPa.
文摘This study systematically investigated the microstructure,mechanical properties,and corrosion behavior of an extruded Zn-0.2Mg alloy processed by multi-directional forging(MDF)at 100℃.The mean grain size was remarkably decreased from 17.2±0.5µm to 1.9±0.3µm,and 84.4%of the microstructure was occupied by grains of below 1µm in size after applying three MDF passes.Electron backscattered difraction examinations revealed that continuous dynamic recrystallization,progressive lattice rotation,and particle-stimulated nucleation mechanisms were recognized as contributing to microstructural evolution.Furthermore,transmission electron microscopy results showed that nanoparticles of Mg/Zn dynamically formed under high strain MDF,while the initial extrusion fber texture was altered to be<0001>parallel to the fnal forging axis.A synergistic efect of grain refnement,texture evolution,second-phase precipitates,and dislocation strengthening resulted in an increased ultimate tensile strength of 232±5 MPa after three MDF passes.However,this was accompanied by a reduction in the elongation(8±2.1%).Additionally,a high corrosion rate of 0.59 mm/year was measured for the experimental alloy fabricated by 3 MDF passes.In agreement with the latter,electrochemical impedance spectroscopy results indicated that the grain refnement improved the passivation kinetics of the oxide layer.
基金Project(2021GK1040) supported by the Major Projects of Scientific and Technology Innovation of Hunan Province,ChinaProjects(52375398,52171018) supported by the National Natural Science Foundation of China+1 种基金Project(Kfkt2023-09) supported by the Open Research Fund of State Key Laboratory of Precision Manufacturing for Extreme Service Performance,Central South University,ChinaProject(E2021203059) supported by the Natural Science Foundation of Hebei Province,China。
文摘This study investigates the differences in microstructural control between cryogenic forging combined with pre-deformation(PCF)and traditional thermal forging(TTF)for 7050 aluminum forgings intended for aerospace applications.The PCF process,utilizing cryogenic deformation,significantly refines the coarse grains at the surface of the forgings,resulting in a finer and more uniform microstructure,thereby effectively addressing the issue of surface coarse grains associated with traditional methods.The findings indicate that the PCF process can accumulate higher stored energy,facilitating static recrystallization(SRX)during subsequent heat treatment and enhancing the microstructural uniformity.Utilizing various analytical techniques,including optical microscopy(OM),electron backscatter diffraction(EBSD),and transmission electron microscopy(TEM).This study reveals the superiority of the PCF process in terms of strain accumulation,dislocation density,and grain refinement.In conclusion,this method offers advantages in enhancing the performance and microstructural uniformity of 7050 aluminum forgings,presenting new opportunities for applications in the aluminum forging industry.
基金supported by National Natural Science Foundation of China(Grant No.52375312)National Key Research and Development Program of China(Grant No.2023YFB4605900)+3 种基金Liaoning Province Science and Technology Plan Joint Program(Grant No.2023JH2/101700299)Open Research Fund of Key Laboratory of Precision Special Machining and Micromanufacturing Technology of Ministry of Education for Dalian University of Technology(Grant No.B202305)Shenzhen National Major Science and Technology Projects(Grant No.CJGJZD20240729113704006)Shenzhen Key Technology R&D Programs(Grant No.JSGG20210420091802007).
文摘Laser-directed energy deposition(LDED)technology has demonstrated great potential for the rapid and integrated fabrication of nickel-based superalloy components.The plastic deformation-assisted method is crucial for achieving grain refinement and microstructural homogeneity in LDED-fabricated superalloys.However,existing methods suffer from uniformity constraints owing to their high deformation resistance,which significantly limits their application in load-bearing components.To address these issues,a synchronous-hot-forging-assisted(SHFA)LDED additive manufacturing method was proposed,and its effects on the macroscopic morphology,microstructure,and mechanical properties of GH4169 nickel-based alloy specimens were systematically compared.The results demonstrated up to 30.1%average plastic deformation in hot-forging components while maintaining good surface flatness.The synergistic effect of dislocation accumulation and dynamic recrystallization during hot forging enables dramatic grain refinement,reducing the average grain size by 89.1%(from 168.5μm to 18.4μm)while weakening texture intensity from 15.31 to 2.15,ultimately promoting equiaxed grain formation.The pores of hot-forging components changed from fine round to flat,the porosity decreased from 0.264%to 0.089%,and the densification level was significantly improved.With the increase in the synchronous hot-forging force,the average ultimate tensile strength of hot-forging components can reach 1175.1 MPa,while the anisotropy difference is gradually weakened.The SHFA-LDED process not only achieves excellent grain refinement and microstructure homogenization but also enhances mechanical properties,providing a new technical path for the additive manufacturing of high-performance nickel-based superalloy components.
基金supported by the National Natural Science Foundation of China(No.51334006)。
文摘To explore ambient strengthening and high temperature ductility,a combined forming approach of multidirectional forging and asymmetric rolling was proposed.A novel multicomponent ultralight Mg-3.11Li-2.31Al-1.95Sn-0.94Y-0.45Er alloy was fabricated.The microstructural evolution and mechanical properties were investigated by microstructural characterization and tensile test.The combined forming results in remarkable grain refinement.The ultimate tensile strength and elongation of(255±7)MPa and 24.9%,respectively,were obtained at room temperature.The contribution of various strengthening mechanisms of the rolled alloy was obtained.Microstructural examination revealed the occurrence of dynamic recrystallization at 473-573 K and dynamic grain growth at 573-623 K.The maximum elongation of 293.9%was demonstrated at 623 K and 5×10^(-4)s^(-1).The dominate deformation mechanism at elevated temperatures is dislocation viscous glide.
文摘Today,I want to share how international standards can forge trust and fuel innovation,laying the foundation for a future where AI benefits everyone,everywhere.First,AI standards,developed jointly by ISO and IEC-the International Electrotechnical Commission-help build global trust and enable responsible innovation by bringing clarity and coherence to an ever-changing AI landscape.As developments in AI continue to emerge at speed,regulation is struggling to keep up and the proliferation of competing standards has created confusion rather than clarity.ISO and our partner IEC are addressing this challenge through the work of our expert committee on AI,SC 42,which takes a holistic,cohesive approach to AI standardization.
基金the financial supports from the Key Research and Development Program of Hunan Province,China(No.2023GK2020)。
文摘The homogenized Mg−5.6Gd−0.8Zn(wt.%)alloys were treated with water cooling and furnace cooling to obtain specimens without and with the 14H long-period stacking ordered(LPSO)phase.Subsequently,multi-directional forging(MDF)experiments were carried out.The microstructure and mechanical properties of different regions(the center,middle and edge regions)in the MDFed alloys were systematically investigated,and the effect of LPSO phase on them was discussed.The results show that the alloys in different regions undergo significant grain refinement during the MDF process.Inhomogeneous microstructures with different degrees of dynamic recrystallization(DRX)are formed,resulting in microhardness heterogeneity.The alloy with the LPSO phase has higher microstructure homogeneity,a higher degree of recrystallization,and better comprehensive mechanical properties than the alloy without the LPSO phase.The furnace-cooled alloy after 18 passes of MDF has the best comprehensive mechanical properties,with an ultimate compressive strength of 488 MPa,yield strength of 258 MPa,and fracture strain of 21.2%.DRX behavior is closely related to the LPSO phase and deformation temperature.The kinked LPSO phase can act as a potential nucleation site for DRX grains,while the fragmented LPSO phase promotes DRX nucleation through the particle-stimulated nucleation mechanism.
基金supported by the Key Program for International Cooperation of the Ministry of Science and Technology,China(No.ZCGX2022001L)。
文摘In-situ TiB_(2)/Al–Cu composite was processed by multidirectional forging(MDF)for six passes.The microstructure evolution of the forged workpiece was examined across various regions.The mechanical properties of the as-cast and MDFed composites were compared,and their strengthening mechanisms were analyzed.Results indicate that the grain refinement achieved through the MDF process is mainly due to the subdivision of the original grains through mechanical geometric fragmentation and the occurrence of dynamic recrystallization(DRX).DRX grains are formed through discontinuous DRX,continuous DRX,and recrystallization induced by particle-stimulated nucleation.A rise in accumulated equivalent strain(Σ?ε)results in finerα-Al grains and a more uniform distribution of TiB_(2)particles,which enhance the Vickers hardness of the composite.In addition,the tensile properties of the MDFed composite significantly improve compared with those of the as-cast composites,with ultimate tensile strength and yield strength increasing by 51.2%and 54%,respectively.This enhancement is primarily due to grain refinement strengthening and dislocation strengthening achieved by the MDF process.
基金supported by the National Natural Science Foundation of China(No.52127808)。
文摘The superplasticity of the Mg−8.59Gd−3.85Y−1.14Zn−0.49Zr alloy was investigated before and after multi-directional forging(MDF)and the mechanisms affecting superplastic deformation were analyzed.The results indicate that after MDF at a temperature of 350℃and strain rates of 0.1 and 0.01 s^(−1)(1-MDFed and 2-MDFed),the superplasticity of the alloy can be significantly improved.The elongations of the MDFed alloys exceed 400%under the strain rate of 6.06×10^(−4)s^(−1)and temperatures of 350,375,and 400℃,and reach the maximum values of 766%(1-MDFed)and 693%(2-MDFed)at 375℃.The grain boundary sliding of the MDFed alloy is sufficient,and the energy barrier of deformation decreases.Theβphase limits the grain growth and promotes dynamic recrystallization,maintaining the stability of the fine-grained structure during superplastic deformation.Several Y-rich phases nucleate in the high-strain region(i.e.,the final fracture region)at high temperatures,accelerating the fracture of the specimen.
基金Projects(50875059,50774026) supported by the National Natural Science Foundation of ChinaProject(20070420023) supported by China Postdoctoral Science FoundationProject (2008AA03A239) supported by High-tech Research and Development Program of China
文摘The semi-solid filling-plastic flowing integrated forging process of semi-solid 6061 Al alloy was simulated by commercial finite element software DEFORM-3D.Temperature,fluid and stress-strain fields were considered in numerical simulation.The simulation results show that the plastic deformation of billet of the ends is higher than that of billet in the straight cylinder.The value of plastic deformation varies with loading mode and plastic deformation fields at the stage of increasing pressure to constant value.When the thixoforging experiments were performed at 590 ℃,15 mm/s of punch velocity and 46 MPa of pressure side urn,it gets the filling wholly and dense internal organization of semi-solid thixoforging parts is gotten.Finite element analysis results are compatible with experimental ones.
基金funded by Department of Science and Technology of Sichuan Province,China(No.2022YFG0102)the China Postdoctoral Science Foundation(No.2023M733314).
文摘The microstructure and mechanical properties of the Ti-5Al-5Mo-5V-1Cr-1Fe(Ti-55511)alloy under different strains were investigated through the design of step-shaped die forging.The results indicate that continuous dynamic recrystallization(CDRX)and discontinuous dynamic recrystallization(DDRX)occur in the high strain region.The orientation of the grains produced by CDRX is random and does not weaken the fiber texture.<100>-oriented grains expand gradually with increasing strain,thereby enhancing the strength of{100}texture.Significant anisotropic mechanical properties are observed in the large strain region and analyzed through in-situ tensile experiments.When the loading direction is parallel to the longitudinal(L)direction,strain concentration is observed near the dynamically recrystallized(DRXed)grains and inside grains oriented along<100>,leading to crack initiation.Furthermore,the small angle between the loading direction and the c-axis hinders the activation of prismatic and basal slip,thereby enhancing the strength.When the loading direction is parallel to the short transverse(ST)direction,cracks are initiated not only within grains oriented along<100>,but also at the grain boundaries.Regarding impact toughness,the elongatedβgrains in the L direction enhance the resistance to crack propagation.
基金Projects (50774026, 50875059) supported by the National Natural Science Foundation of ChinaProject (20070420023) supported by the China Postdoctoral Science FoundationProject (2008AA03A239) supported by the National High-tech Research and Development Program of China
文摘The homogenization on microstructure and mechanical properties of 2A50 aluminum alloy prepared by liquid forging was investigated.Wheel hubs were produced using direct and compound loading.The results show that the microstructure and mechanical properties are inhomogeneous in direct forged samples.The microstructure of the wall is coarser than that of the base,and the mechanical properties are lower and some defects are detected at the wheel corner.Using compound loading,the microstructure and mechanical properties of the wall are improved evidently.With increasing feeding amount,the microstructure and mechanical properties become more homogeneous.The defects disappear when the feeding amount is 4 mm.The forged wheel hubs could obtain fine and homogeneous microstructure with grain size of 20-30 μm,tensile strength of 355 MPa and elongation of 10% when the feeding amount is 10 mm.The microstructure and mechanical properties of liquid forged workpieces could be controlled and homogenized using compound loading.
基金Project(2012B090600051)supported by the Guangdong Provincial Department of Science and Technology,ChinaProject(2013EG115006)supported by the Special Program for Technology Development from the Ministry of Science and Technology of China
文摘The A356 aluminum alloy wheels were prepared by thixo-forging combined with a low superheat casting process. The as-cast microstructure, microstructure evolution during reheating and the mechanical properties of the thixo-forged A356 aluminum alloy wheels were investigated. The results show that the A356 aluminum alloy billet with fine, uniform and non-dendritic grains can be obtained when the melt is cast at 635 ℃. When the billet is reheated at 600 ℃ for 60 min, the non-dendritic grains are changed into spherical ones and the billet can be easily thixo-forged into wheels. The tensile strength and elongation of thixo-forged wheels with T6 heat treatment are 327.6 MPa and 7.8%, respectively, which are higher than those of a cast wheel. It is suggested that the thixo-forging combined with the low superheat casting process is an effective technique to produce aluminum alloy wheels with high mechanical properties.
基金Projects(51204053,51074048,51204048)supported by the National Natural Science Foundation of ChinaProject(20110491518)supported by China Postdoctoral Science FoundationProject(2012CB619506)supported by the National Basic Research Program of China
文摘The effect of forging passes on the refinement of high purity aluminum during multi-forging was investigated. The attention was focused on the structure uniformity due to deformation uniformity and the grain refinement limitation with very high strains. The results show that the fine grain zone in the center of sample expands gradually with the increase of forging passes. When the forging passes reach 6, an X-shape fine grain zone is initially formed. With a further increase of the passes, this X-shape zone tends to spread the whole sample. Limitation in the structural refinement is observed with increasing strains during multi-forging process at the room temperature. The grains size in the center is refined to a certain size （110 μm as forging passes reach 12, and there is no further grain refinement in the center with increasing the forging passes to 24. However, the size of the coarse grains near the surface is continuously decreased with increasing the forging passes to 24.
文摘Microstructure and mechanical properties of AZ61 Mg alloy during isothermal multi-axial forging （MAF） were studied. The mechanisms of grain refinement and relationship between the microstructures and mechanical properties were discussed. The results show that the average grain size decreases with increasing the number of MAF passes. The grains are significantly refined at the 1st and 2nd MAF passes, and gradually refined at higher MAF passes. The initial grain size of 148 lam decreases to about 14 gm after 6 MAF passes. The grain refinement occurs mainly by continuous dynamic recrystallization. With increasing the MAF passes, both the tensile strength and the elongation to failure of the alloy are significantly enhanced.
