To investigate the overall performance of reverse energy bypass scramjet,firstly a variable spe⁃cific heat method combined with a chemical balance calculation module for combustion products were used to es⁃tablish a b...To investigate the overall performance of reverse energy bypass scramjet,firstly a variable spe⁃cific heat method combined with a chemical balance calculation module for combustion products were used to es⁃tablish a benchmark scramjet performance evaluation model.Based on the test data of typical flying point of Mach 7 with the altitude of 29 km,the reliability of the model was verified.The deviations of parameters such as the to⁃tal pressure loss of combustor between the model and the test data were analyzed.Furtherly,an analytical method for post-combustion magnetohydrodynamic power generation was established;by embedding the above method into the overall performance evaluation model,performance prediction considering the power generation effect was realized.Finally,based on the above model,variety regulations of the inlet and the outlet parameters of the power generation channel and performance parameters including the engine specific impulse and the unit thrust under different enthalpy extraction ratios and load factors were analyzed.It could be concluded that the model can reliably predict the variations of key parameters.As the value of the load factor increases,the value of the conduc⁃tivity required to reach the specified enthalpy extraction ratio first decreases and then increases,which is approxi⁃mately parabolic.In order to reduce the demand for the gas conductivity for MHD power generation,the load fac⁃tor should be around 0.5.When the load factor is 0.4 and the magnetic induction intensity is 2.5 T,if the enthalpy extraction ratio reaches 0.5%,the engine specific impulse performance reduces about 3.58%.展开更多
The kerosene-fueled Scramjet with multi-cavity combustor has the potential to serve aspropulsion system for hypersonic flight.However,the impact of injection positions on combustionperformance and mechanism at high Ma...The kerosene-fueled Scramjet with multi-cavity combustor has the potential to serve aspropulsion system for hypersonic flight.However,the impact of injection positions on combustionperformance and mechanism at high Mach numbers remains uncertain.Therefore,a comparativestudy was conducted using numerical methods to explore multi-cavity Scramjet combustor perfor-mance at a flight Mach number 7.0 with different injection positions.The combustor is equippedwith 6 cavities arranged in three groups along the flow direction,each consisting of two cavities per-pendicular to the flow.It is shown that the injection location significantly influences combustionperformance:Front-injection yields higher combustion efficiency than post-injection,but post-injection is advantageous for the intake start.Additionally,regardless of injection positions,themainstream flow state near the cavities behind the injection can be categorized as supersonic flow,supersonic-subsonic coexistence flow,and subsonic flow.The optimal length from the downstreamto the trailing edge of the cavities behind the injection for achieving maximum combustion effi-ciency is determined.Further extension beyond this optimal length does not significantly increasethe combustion efficiency.In addition,the optimal length varies with different injection positions-specifically,it is about 60%longer with post-injection conditions than with front-injection con-ditions in this investigation.Moreover,significant secondary combustion within the cavities leadingto improved efficiency only occurs when mainstream flow state is either supersonic flow orsupersonic-subsonic coexistence flow.Also,with a well-optimized design,the kerosene-fueledmulti-cavity Scramjet can achieve enhanced combustion efficiency,which shows relatively smallvariation across a wide range of equivalence ratios.This might be caused by the effects of interac-tion among these multiple cavities.Therefore,these research findings can provide valuable insightsfor designing and optimizing the kerosene-fueled multi-cavity combustor in Scramjet at high Machnumbers.展开更多
Scramjet is the most promising propulsion system for Air-breathing Hypersonic Vehicle(AHV),and the Infrared(IR)radiation it emits is critical for early warning,detection,and identification of such weapons.This work pr...Scramjet is the most promising propulsion system for Air-breathing Hypersonic Vehicle(AHV),and the Infrared(IR)radiation it emits is critical for early warning,detection,and identification of such weapons.This work proposes an Adaptive Reverse Monte Carlo(ARMC)method and develops an analytical model for the IR radiation of scramjet considering gaseous kerosene and hydrogen fueled conditions.The evaluation studies show that at a global equivalence ratio of 0.8,the IR radiation from hydrogen-fueled plume is predominantly from H_(2)O and spectral peak is 1.53 kW·Sr^(-1)·μm^(-1)at the 2.7μm band,while the kerosene-fueled plume exhibits a spectral intensity approaching 7.0 kW·Sr^(-1)·μm^(-1)at the 4.3μm band.At the backward detection angle,both types of scramjets exhibit spectral peaks within the 1.3-1.4μm band,with intensities around10 kW·Sr^(-1)·μm^(-1).The integral radiation intensity of hydrogen-fueled scramjet is generally higher than kerosene-fueled scramjet,particularly in 1-3μm band.Meanwhile,at wide detection angles,the solid walls become the predominant radiation source.The radiation intensity is highest in1-3μm and weakest in 8-14μm band,with values of 21.5 kW·Sr^(-1)and 0.57 kW·Sr^(-1)at the backward detection angles,respectively.Significant variations in the radiation contributions from gases and solids are observed across different bands under the two fuel conditions,especially within 3-5μm band.This research provides valuable insights into the IR radiation characteristics of scramjets,which can aid in the development of IR detection systems for AHV.展开更多
To investigate the problem of ethylene jet mixing and combustion in the scramjet at high Mach number(Ma = 8), numerical simulations were carried out for different equivalent ratios at cold and combustion conditions, i...To investigate the problem of ethylene jet mixing and combustion in the scramjet at high Mach number(Ma = 8), numerical simulations were carried out for different equivalent ratios at cold and combustion conditions, in which three-dimensional steady compressible RANS and k-ω SST turbulence model were adopted. It demonstrates that as the equivalence ratio increases from 0.42 to 1.08, the combustion becomes more intensified, and the higher backpressure pushes flame to propagate upstream. The supersonic combustion region in the combustor decreases from 92% to 85% with the increase of equivalence ratio from 0.42 to 1.08, resulting in the transition of the combustor from scram-mode to dual-mode. Both mixing and combustion efficiencies decrease by 35% and 16% respectively when the equivalence ratio increases from 0.42 to 1.08, indicating that the high equivalence ratio is unfavorable to the mixing and combustion processes. Combustion mode analysis reveals that the flame in the cavity under the high Mach number is dominated by non-premixed flames, i.e., more than 95% behaves as non-premixed mode, and the heat release is also mainly contributed by non-premixed flame. Increasing the equivalence ratio is beneficial to the thrust performance. Although the viscous force hardly changes with equivalence ratio, the percentage of pressure force used to balance the viscous force increases gradually,which limits the engine performance.展开更多
To reduce the drag generated by the recirculation flow at the rocket base in a RocketBased Combined Cycle(RBCC)engine operating in the ramjet/scramjet mode,a novel annular rocket RBCC engine based on a central plug co...To reduce the drag generated by the recirculation flow at the rocket base in a RocketBased Combined Cycle(RBCC)engine operating in the ramjet/scramjet mode,a novel annular rocket RBCC engine based on a central plug cone was proposed.The performance loss mechanism caused by the recirculation flow at the rocket base and the influence of the plug cone configuration on the thrust performance were studied.Results indicated that the recirculation flow at the rocket base extended through the entire combustor,which creates an extensive range of the"low-kineticenergy zone"at the center and leads to an engine thrust loss.The plug cone serving as a surface structure had a restrictive effect on the internal flow of the engine,making it smoothly transit at the position of the large separation zone.The model RBCC engine could achieve a maximum thrust augmentation of 37.6%with a long plug cone that was twice diameter of the inner isolator.However,a shorter plug cone that was half diameter of the inner isolator proved less effective at reducing the recirculation flow for a supersonic flow and induced an undesirable flow fraction that diminished the thrust performance.Furthermore,the effectiveness of the plug cone increased with the flight Mach number,indicating that it could further broaden the operating speed range of the scramjet mode.展开更多
The uniform design and response surface methodology （RSM） are applied to the multi-objective optimization of a 2-D mixed compression scramjet inlet. The set of experimental design points on the design space is selec...The uniform design and response surface methodology （RSM） are applied to the multi-objective optimization of a 2-D mixed compression scramjet inlet. The set of experimental design points on the design space is selected by the uniform design, and the inlet performance is analyzed by computational fluid dynamics （CFD）. Then complete quadratic polynomial response surface approximation models are constructed based on the performance analysis results and then used to replace theoriginal complex inlet performance model. The optimization is conducted using a multi-objective genetic algorithm NSGA-Ⅱ, and the Pareto optimal solution set is obtained. Results show that the uniform design and RSM can reduce the computational complexity of numerical simulation and improve the optimization efficiency.展开更多
In order to investigate the effects of fuel injection distribution on the scrarnjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The resu...In order to investigate the effects of fuel injection distribution on the scrarnjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combustor performances. In addition, an irmer-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.展开更多
This article investigates and presents the influences of geometric parameters of a scramjet exerting upon its nozzle performances. These parameters include divergent angles, total lengths, height ratios, cowl lengths,...This article investigates and presents the influences of geometric parameters of a scramjet exerting upon its nozzle performances. These parameters include divergent angles, total lengths, height ratios, cowl lengths, and cowl angles. The flow field within the scramjet nozzle is simulated numerically by using the CFD software--FLUENT in association with coupled implicit solver and an RNG k-ε turbulence model.展开更多
The solid-fueled Scramjet is an interesting option for supersonic combustion ramjet.It shows significant advantages such as simple fuel supply and compactness,avoiding the complex system of tanks and pipelines that en...The solid-fueled Scramjet is an interesting option for supersonic combustion ramjet.It shows significant advantages such as simple fuel supply and compactness,avoiding the complex system of tanks and pipelines that encountered in liquid-fueled Scramjets.The solid-fueled Scramjet could be the simplest air-breathing engine for the hypersonic flight regime.This paper presents a comprehensive and systematic review of the research progress on solid-fueled Scramjet in various institutes and universities.It summarizes a progress overview of three types of the solid-fueled Scramjet,which covers a wealth of landmark numerical and experimental results.Based on this,several relevant key technologies are proposed.Several inherent scientific issues are refined,such as the mixing mechanism of multi-phase flow and supersonic airflow,ignition and combustion mechanism of the condensed phase in a supersonic airflow,and coupling mechanism of gas and solid phase in a supersonic flow.Finally,the historical development trend is clarified,and some recommendations are provided for future solid-fueled Scramjet.展开更多
Combustion mode transition is a valuable and challenging research area in dual-mode scramjet engines.The thermal behavior of an isolator with mode transition inducing backpressure is investigated by direct-connect dua...Combustion mode transition is a valuable and challenging research area in dual-mode scramjet engines.The thermal behavior of an isolator with mode transition inducing backpressure is investigated by direct-connect dual-mode scramjet experiments and theoretical analysis.Combustion experiments are conducted under the incoming airflow conditions of total temperature1270 K and Mach 2.A small increment of the fuel equivalence ratio is scheduled to trigger mode transition.Correspondingly,the variation of the coolant flow rate is very small.Based on the measured wall pressures,the heat-transfer model can quantify the thermal state variation of the engine with active cooling.Compared with the combustor,mode transition has a greater effect on the isolator thermal behavior,and it significantly changes the isolator heat-flux and wall temperature.To further study the isolator thermal behavior from flight Mach 4 to Mach 7,a theoretical analysis is carried out.Around the critical point of combustion mode transition,sudden changes of the isolator flowfield and thermal state are discussed.展开更多
The asymmetric separation has a crucial effect on the performance of the scramjet.In this study,the asymmetric separation and combustion in both rectangular and circular scramjets are investigated numerically,and the ...The asymmetric separation has a crucial effect on the performance of the scramjet.In this study,the asymmetric separation and combustion in both rectangular and circular scramjets are investigated numerically,and the effect of injection scheme is analyzed.The characteristics of the flow field are analyzed based on sufficient code verification.In the rectangular scramjet,the separation tends to occur in the corner due to the corner boundary-layer effect.The separation is asym-metric and only two corners have serious separation.The fuel penetration depth in the separation zone increases and the combustion is intensified.When the injection scheme is uniform,both the combustion and separation become weak.In the circular scramjet,the separation and combustion are basically axisymmetric in the scramjet with one-row injection scheme.The asymmetric combustion becomes obvious in cases with multi-row injection scheme.When the injection orifices distribute intensively on the top and bottom sides,the strongest and weakest separations occur near these two sides respectively.When the distribution of orifices becomes uniform,the direction of separation cannot be predicted.For multi-row cases,the nonuniform injection scheme could result in violent combustion and asymmetric flow structures compared with the uniform injection scheme.展开更多
A scramjet combustor with double cavitybased flameholders was experimentally studied in a directconnected test bed with the inflow conditions of M = 2.64,Pt = 1.84 MPa,Tt = 1 300 K.Successful ignition and selfsustaine...A scramjet combustor with double cavitybased flameholders was experimentally studied in a directconnected test bed with the inflow conditions of M = 2.64,Pt = 1.84 MPa,Tt = 1 300 K.Successful ignition and selfsustained combustion with room temperature kerosene was achieved using pilot hydrogen,and kerosene was vertically injected into the combustor through 4×φ 0.5 mm holes mounted on the wall.For different equivalence ratios and different injection schemes with both tandem cavities and parallel cavities,flow fields were obtained and compared using a high speed camera and a Schlieren system.Results revealed that the combustor inside the flow field was greatly influenced by the cavity installation scheme,cavities in tandem easily to form a single side flame distribution,and cavities in parallel are more likely to form a joint flame,forming a choked combustion mode.The supersonic combustion flame was a kind of diffusion flame and there were two kinds of combustion modes.In the unchoked combustion mode,both subsonic and supersonic combustion regions existed.While in the choked mode,the combustion region was fully subsonic with strong shock propagating upstream.Results also showed that there was a balance point between the boundary separation and shock enhanced combustion,depending on the intensity of heat release.展开更多
The combustion modes in two different scramjet combustors with the mass flow rates of 1.8 kg/s and 3.6 kg/s are experimentally investigated to explore the scaling effects on supersonic combustion with a Mach number 2....The combustion modes in two different scramjet combustors with the mass flow rates of 1.8 kg/s and 3.6 kg/s are experimentally investigated to explore the scaling effects on supersonic combustion with a Mach number 2.0 inflow.It is found that the scramjet combustor with a larger scale can broaden the flame rich blowout limit.As the Equivalence Ratio(ER)increases,the combustion in the small-scale combustor maintains in the cavity-stabilized mode,and the flamebase moves downstream along the cavity shear layer;however,the combustion in the large-scale combustor gradually transfers from the cavity-stabilized mode to the jet-wake-stabilized mode.The differences in the cavity residence time,the ignition delay time and the Damkohler number caused by different scales of the scramjet combustor are likely to account for the scaling effects on the combustion modes.展开更多
Flow instability of supercritical hydrocarbon fuel is a crucial issue in scramjet regenerative cooling structure. In this study, flow excursion instability and flow distribution in parallel tubes were experimentally s...Flow instability of supercritical hydrocarbon fuel is a crucial issue in scramjet regenerative cooling structure. In this study, flow excursion instability and flow distribution in parallel tubes were experimentally studied for supercritical fluids. Two types of flow excursion occur in a single tube. Type Ⅰ and Type Ⅱ excursions, and they are corresponding to decreasing and increasing flow rate respectively. They can trigger flow maldistribution between parallel tubes and the hysteresis phenomenon of flow distribution. The effects of system parameters, including inlet temperature,system pressure, and heat flux, on flow distribution were analyzed. In addition, the relationship between flow excursion and the pseudo-critical interval proposed in the literature was established according to the heated tube outlet temperature at the onset of flow instability. Finally, the flow excursion instability boundary was obtained using two dimensionless parameters. These experimental results can provide helpful insight on the mechanism of Scramjet regenerative cooling.展开更多
文摘To investigate the overall performance of reverse energy bypass scramjet,firstly a variable spe⁃cific heat method combined with a chemical balance calculation module for combustion products were used to es⁃tablish a benchmark scramjet performance evaluation model.Based on the test data of typical flying point of Mach 7 with the altitude of 29 km,the reliability of the model was verified.The deviations of parameters such as the to⁃tal pressure loss of combustor between the model and the test data were analyzed.Furtherly,an analytical method for post-combustion magnetohydrodynamic power generation was established;by embedding the above method into the overall performance evaluation model,performance prediction considering the power generation effect was realized.Finally,based on the above model,variety regulations of the inlet and the outlet parameters of the power generation channel and performance parameters including the engine specific impulse and the unit thrust under different enthalpy extraction ratios and load factors were analyzed.It could be concluded that the model can reliably predict the variations of key parameters.As the value of the load factor increases,the value of the conduc⁃tivity required to reach the specified enthalpy extraction ratio first decreases and then increases,which is approxi⁃mately parabolic.In order to reduce the demand for the gas conductivity for MHD power generation,the load fac⁃tor should be around 0.5.When the load factor is 0.4 and the magnetic induction intensity is 2.5 T,if the enthalpy extraction ratio reaches 0.5%,the engine specific impulse performance reduces about 3.58%.
基金financially supported by the National Key Laboratory of Ramjet,China(No.2022-020-003)the Fundamental Research Funds for the Central Universities,China(No.501QYZX2023146001)。
文摘The kerosene-fueled Scramjet with multi-cavity combustor has the potential to serve aspropulsion system for hypersonic flight.However,the impact of injection positions on combustionperformance and mechanism at high Mach numbers remains uncertain.Therefore,a comparativestudy was conducted using numerical methods to explore multi-cavity Scramjet combustor perfor-mance at a flight Mach number 7.0 with different injection positions.The combustor is equippedwith 6 cavities arranged in three groups along the flow direction,each consisting of two cavities per-pendicular to the flow.It is shown that the injection location significantly influences combustionperformance:Front-injection yields higher combustion efficiency than post-injection,but post-injection is advantageous for the intake start.Additionally,regardless of injection positions,themainstream flow state near the cavities behind the injection can be categorized as supersonic flow,supersonic-subsonic coexistence flow,and subsonic flow.The optimal length from the downstreamto the trailing edge of the cavities behind the injection for achieving maximum combustion effi-ciency is determined.Further extension beyond this optimal length does not significantly increasethe combustion efficiency.In addition,the optimal length varies with different injection positions-specifically,it is about 60%longer with post-injection conditions than with front-injection con-ditions in this investigation.Moreover,significant secondary combustion within the cavities leadingto improved efficiency only occurs when mainstream flow state is either supersonic flow orsupersonic-subsonic coexistence flow.Also,with a well-optimized design,the kerosene-fueledmulti-cavity Scramjet can achieve enhanced combustion efficiency,which shows relatively smallvariation across a wide range of equivalence ratios.This might be caused by the effects of interac-tion among these multiple cavities.Therefore,these research findings can provide valuable insightsfor designing and optimizing the kerosene-fueled multi-cavity combustor in Scramjet at high Machnumbers.
基金supported by the National Natural Science Foundation of China(No.12102356)。
文摘Scramjet is the most promising propulsion system for Air-breathing Hypersonic Vehicle(AHV),and the Infrared(IR)radiation it emits is critical for early warning,detection,and identification of such weapons.This work proposes an Adaptive Reverse Monte Carlo(ARMC)method and develops an analytical model for the IR radiation of scramjet considering gaseous kerosene and hydrogen fueled conditions.The evaluation studies show that at a global equivalence ratio of 0.8,the IR radiation from hydrogen-fueled plume is predominantly from H_(2)O and spectral peak is 1.53 kW·Sr^(-1)·μm^(-1)at the 2.7μm band,while the kerosene-fueled plume exhibits a spectral intensity approaching 7.0 kW·Sr^(-1)·μm^(-1)at the 4.3μm band.At the backward detection angle,both types of scramjets exhibit spectral peaks within the 1.3-1.4μm band,with intensities around10 kW·Sr^(-1)·μm^(-1).The integral radiation intensity of hydrogen-fueled scramjet is generally higher than kerosene-fueled scramjet,particularly in 1-3μm band.Meanwhile,at wide detection angles,the solid walls become the predominant radiation source.The radiation intensity is highest in1-3μm and weakest in 8-14μm band,with values of 21.5 kW·Sr^(-1)and 0.57 kW·Sr^(-1)at the backward detection angles,respectively.Significant variations in the radiation contributions from gases and solids are observed across different bands under the two fuel conditions,especially within 3-5μm band.This research provides valuable insights into the IR radiation characteristics of scramjets,which can aid in the development of IR detection systems for AHV.
文摘To investigate the problem of ethylene jet mixing and combustion in the scramjet at high Mach number(Ma = 8), numerical simulations were carried out for different equivalent ratios at cold and combustion conditions, in which three-dimensional steady compressible RANS and k-ω SST turbulence model were adopted. It demonstrates that as the equivalence ratio increases from 0.42 to 1.08, the combustion becomes more intensified, and the higher backpressure pushes flame to propagate upstream. The supersonic combustion region in the combustor decreases from 92% to 85% with the increase of equivalence ratio from 0.42 to 1.08, resulting in the transition of the combustor from scram-mode to dual-mode. Both mixing and combustion efficiencies decrease by 35% and 16% respectively when the equivalence ratio increases from 0.42 to 1.08, indicating that the high equivalence ratio is unfavorable to the mixing and combustion processes. Combustion mode analysis reveals that the flame in the cavity under the high Mach number is dominated by non-premixed flames, i.e., more than 95% behaves as non-premixed mode, and the heat release is also mainly contributed by non-premixed flame. Increasing the equivalence ratio is beneficial to the thrust performance. Although the viscous force hardly changes with equivalence ratio, the percentage of pressure force used to balance the viscous force increases gradually,which limits the engine performance.
基金supported by the National Natural Science Foundation of China(Nos.11925207 and 92252206)the Hunan Province Graduate Innovation Project,China(No.XJCX2023059)。
文摘To reduce the drag generated by the recirculation flow at the rocket base in a RocketBased Combined Cycle(RBCC)engine operating in the ramjet/scramjet mode,a novel annular rocket RBCC engine based on a central plug cone was proposed.The performance loss mechanism caused by the recirculation flow at the rocket base and the influence of the plug cone configuration on the thrust performance were studied.Results indicated that the recirculation flow at the rocket base extended through the entire combustor,which creates an extensive range of the"low-kineticenergy zone"at the center and leads to an engine thrust loss.The plug cone serving as a surface structure had a restrictive effect on the internal flow of the engine,making it smoothly transit at the position of the large separation zone.The model RBCC engine could achieve a maximum thrust augmentation of 37.6%with a long plug cone that was twice diameter of the inner isolator.However,a shorter plug cone that was half diameter of the inner isolator proved less effective at reducing the recirculation flow for a supersonic flow and induced an undesirable flow fraction that diminished the thrust performance.Furthermore,the effectiveness of the plug cone increased with the flight Mach number,indicating that it could further broaden the operating speed range of the scramjet mode.
文摘The uniform design and response surface methodology （RSM） are applied to the multi-objective optimization of a 2-D mixed compression scramjet inlet. The set of experimental design points on the design space is selected by the uniform design, and the inlet performance is analyzed by computational fluid dynamics （CFD）. Then complete quadratic polynomial response surface approximation models are constructed based on the performance analysis results and then used to replace theoriginal complex inlet performance model. The optimization is conducted using a multi-objective genetic algorithm NSGA-Ⅱ, and the Pareto optimal solution set is obtained. Results show that the uniform design and RSM can reduce the computational complexity of numerical simulation and improve the optimization efficiency.
文摘In order to investigate the effects of fuel injection distribution on the scrarnjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combustor performances. In addition, an irmer-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.
文摘This article investigates and presents the influences of geometric parameters of a scramjet exerting upon its nozzle performances. These parameters include divergent angles, total lengths, height ratios, cowl lengths, and cowl angles. The flow field within the scramjet nozzle is simulated numerically by using the CFD software--FLUENT in association with coupled implicit solver and an RNG k-ε turbulence model.
基金supported by the China Scholarship Council and the National Natural Science Foundation of China(Nos.2020JJ4665,51706241).
文摘The solid-fueled Scramjet is an interesting option for supersonic combustion ramjet.It shows significant advantages such as simple fuel supply and compactness,avoiding the complex system of tanks and pipelines that encountered in liquid-fueled Scramjets.The solid-fueled Scramjet could be the simplest air-breathing engine for the hypersonic flight regime.This paper presents a comprehensive and systematic review of the research progress on solid-fueled Scramjet in various institutes and universities.It summarizes a progress overview of three types of the solid-fueled Scramjet,which covers a wealth of landmark numerical and experimental results.Based on this,several relevant key technologies are proposed.Several inherent scientific issues are refined,such as the mixing mechanism of multi-phase flow and supersonic airflow,ignition and combustion mechanism of the condensed phase in a supersonic airflow,and coupling mechanism of gas and solid phase in a supersonic flow.Finally,the historical development trend is clarified,and some recommendations are provided for future solid-fueled Scramjet.
文摘Combustion mode transition is a valuable and challenging research area in dual-mode scramjet engines.The thermal behavior of an isolator with mode transition inducing backpressure is investigated by direct-connect dual-mode scramjet experiments and theoretical analysis.Combustion experiments are conducted under the incoming airflow conditions of total temperature1270 K and Mach 2.A small increment of the fuel equivalence ratio is scheduled to trigger mode transition.Correspondingly,the variation of the coolant flow rate is very small.Based on the measured wall pressures,the heat-transfer model can quantify the thermal state variation of the engine with active cooling.Compared with the combustor,mode transition has a greater effect on the isolator thermal behavior,and it significantly changes the isolator heat-flux and wall temperature.To further study the isolator thermal behavior from flight Mach 4 to Mach 7,a theoretical analysis is carried out.Around the critical point of combustion mode transition,sudden changes of the isolator flowfield and thermal state are discussed.
基金supported by the National Natural Science Foundation of China(Nos.11925207,12002381)the Scientific Research Plan of National University of Defense Technology in 2019,China(No.ZK19-02)+1 种基金the Postgraduate Scientific Research Innovation Project of Hunan Province,China(No.CX20200084)the Equipment Pre-research Foundation of Key Laboratory,China(No.6142703200311)。
文摘The asymmetric separation has a crucial effect on the performance of the scramjet.In this study,the asymmetric separation and combustion in both rectangular and circular scramjets are investigated numerically,and the effect of injection scheme is analyzed.The characteristics of the flow field are analyzed based on sufficient code verification.In the rectangular scramjet,the separation tends to occur in the corner due to the corner boundary-layer effect.The separation is asym-metric and only two corners have serious separation.The fuel penetration depth in the separation zone increases and the combustion is intensified.When the injection scheme is uniform,both the combustion and separation become weak.In the circular scramjet,the separation and combustion are basically axisymmetric in the scramjet with one-row injection scheme.The asymmetric combustion becomes obvious in cases with multi-row injection scheme.When the injection orifices distribute intensively on the top and bottom sides,the strongest and weakest separations occur near these two sides respectively.When the distribution of orifices becomes uniform,the direction of separation cannot be predicted.For multi-row cases,the nonuniform injection scheme could result in violent combustion and asymmetric flow structures compared with the uniform injection scheme.
文摘A scramjet combustor with double cavitybased flameholders was experimentally studied in a directconnected test bed with the inflow conditions of M = 2.64,Pt = 1.84 MPa,Tt = 1 300 K.Successful ignition and selfsustained combustion with room temperature kerosene was achieved using pilot hydrogen,and kerosene was vertically injected into the combustor through 4×φ 0.5 mm holes mounted on the wall.For different equivalence ratios and different injection schemes with both tandem cavities and parallel cavities,flow fields were obtained and compared using a high speed camera and a Schlieren system.Results revealed that the combustor inside the flow field was greatly influenced by the cavity installation scheme,cavities in tandem easily to form a single side flame distribution,and cavities in parallel are more likely to form a joint flame,forming a choked combustion mode.The supersonic combustion flame was a kind of diffusion flame and there were two kinds of combustion modes.In the unchoked combustion mode,both subsonic and supersonic combustion regions existed.While in the choked mode,the combustion region was fully subsonic with strong shock propagating upstream.Results also showed that there was a balance point between the boundary separation and shock enhanced combustion,depending on the intensity of heat release.
基金supported by the National Natural Science Foundation of China(Nos.11925207,11902353 and 91741205)the Foundation of Innovation-oriented Province Construction of Hunan(No.2019RS2028)。
文摘The combustion modes in two different scramjet combustors with the mass flow rates of 1.8 kg/s and 3.6 kg/s are experimentally investigated to explore the scaling effects on supersonic combustion with a Mach number 2.0 inflow.It is found that the scramjet combustor with a larger scale can broaden the flame rich blowout limit.As the Equivalence Ratio(ER)increases,the combustion in the small-scale combustor maintains in the cavity-stabilized mode,and the flamebase moves downstream along the cavity shear layer;however,the combustion in the large-scale combustor gradually transfers from the cavity-stabilized mode to the jet-wake-stabilized mode.The differences in the cavity residence time,the ignition delay time and the Damkohler number caused by different scales of the scramjet combustor are likely to account for the scaling effects on the combustion modes.
基金co-supported by the Open Fund of Key Laboratory of Power Research of China(No.2017-Ⅲ-0005-0029)the National Natural Science Foundation of China(No.51776167).
文摘Flow instability of supercritical hydrocarbon fuel is a crucial issue in scramjet regenerative cooling structure. In this study, flow excursion instability and flow distribution in parallel tubes were experimentally studied for supercritical fluids. Two types of flow excursion occur in a single tube. Type Ⅰ and Type Ⅱ excursions, and they are corresponding to decreasing and increasing flow rate respectively. They can trigger flow maldistribution between parallel tubes and the hysteresis phenomenon of flow distribution. The effects of system parameters, including inlet temperature,system pressure, and heat flux, on flow distribution were analyzed. In addition, the relationship between flow excursion and the pseudo-critical interval proposed in the literature was established according to the heated tube outlet temperature at the onset of flow instability. Finally, the flow excursion instability boundary was obtained using two dimensionless parameters. These experimental results can provide helpful insight on the mechanism of Scramjet regenerative cooling.
