An experimental investigation is conducted to evaluate the performance and the stalling process of a fan subjected to inlet swirls,as well as the effectiveness of an Impedance Boundary-Controlled(IBC)Casing Treatment(...An experimental investigation is conducted to evaluate the performance and the stalling process of a fan subjected to inlet swirls,as well as the effectiveness of an Impedance Boundary-Controlled(IBC)Casing Treatment(CT)on the stall margin recovery.An operating cycle is proposed based on the hysteresis effect of harmonic flap oscillation of airfoils and parallel compressor theory to explain the pressure characteristic of the fan under twin swirl inlets.Twin swirls are observed to reduce the stall margin of the fan,and the circumferential location where the spike is detected turns to the intersection area of the twin swirl.The IBC CT is proven to extend the stall margin of the fan for 12.7%–22.3%when subjected to inlet swirls with an efficiency loss of around 1%.The IBC CT helps to reduce the size of the operating cycle of the fan by redistributing the blade loading and adding the system damping to dissipate the perturbation energy.展开更多
Aim To obtain an optimizing range of the main configuration parameters of double swirls combustion system (DSCS) Methods To analyze the influence of DS combustion cham-ber configuration parameters on fuel spray and mi...Aim To obtain an optimizing range of the main configuration parameters of double swirls combustion system (DSCS) Methods To analyze the influence of DS combustion cham-ber configuration parameters on fuel spray and mixing by means of the fuel jet developmentperiphery charts obtained by the high speed photography with a modeling test device deve-loped by authors,and to examine it by the tests on a single cylinder diesel engine.Resultsand Conclusion The mixing process can be divided into four phases.The optimizing range of the ration of the inner chamber diameter to the cylinder bore,d2/D,is 0.4-0.7; and the outerchamber diameter,d1 the height of the circular ridge to the piston top face,h1,the radius of outer/inner chamber circle,R1,R2 ,the max depth of outer/inner chamber bowl,H1,H2,etc. are also important展开更多
In recent years,research investigations have focused on the substantial freshwater storage in the Beaufort Gyre(BG)region due to climate change.Despite active mesoscale eddies in the area,a notable gap in understandin...In recent years,research investigations have focused on the substantial freshwater storage in the Beaufort Gyre(BG)region due to climate change.Despite active mesoscale eddies in the area,a notable gap in understanding the three-dimensional structure and induced transport has been observed.This study concentrates on the Canada Basin in the western Arctic Ocean,specifically examining a subsurface anticyclonic eddy(SAE)sampled by a Mooring A in the BG region.Hybrid Coordinate Ocean Model(HYCOM)analysis data reveal its lifecycle from February 15 to March 15,2017,marked by initiation,development,maturity,decay,and termination stages.This work extends the finding of SAE passing through Mooring A by examining its overall effects,spatiotemporal variations,and swirl transport.SAE generation through baroclinic instability,which contributes to the westward tilt of the vertical axis,is also confirmed in this study.Swirl transport induced by SAE is predominantly eastward and downward due to its trajectory and background flow.SAE temporarily weakens stratification and extends the subsurface depth but demonstrates transient effects.Moreover,SAE transports upper-layer freshwater,Pacific Winter Water,and Atlantic Water downward,emphasizing its potential influence on freshwater redistribution in the Canadian Basin.This research provides valuable insights into mesoscale eddy dynamics,revealing their role in modulating the upper water mass in the BG region.展开更多
The electromagnetic swirling flow in nozzle(EMSFN)technique is designed to mitigate the adverse effects of unstable and uneven flow within the submerged entry nozzle in continuous casting.Utilizing electromagnetic for...The electromagnetic swirling flow in nozzle(EMSFN)technique is designed to mitigate the adverse effects of unstable and uneven flow within the submerged entry nozzle in continuous casting.Utilizing electromagnetic forces,EMSFN stabilizes the flow within the nozzle,leading to a more controlled flow in the mold.Numerical simulations were used to quantitatively analyze the magnetic and flow fields in a slab continuous casting system under EMSFN.Results indicate that EMSFN significantly stabilizes the outflow from the nozzle,with stability increasing with higher current intensity.At 10,000 Ampere-turns(At)of the coil,meniscus fluctuations were unstable.They stabilized at 13,000 At,with minimal changes observed beyond this point.The optimal current intensity for stable mold flow,at a casting speed of 1.56 m/min,is 13,000 At.These findings confirm the effectiveness of EMSFN in stabilizing the internal flow field of the slab mold and determining optimal operational current intensity.展开更多
Controlling molten steel flow in the mold and stabilizing the meniscus are critical challenges during the continuous casting,directly impacting the surface quality and internal quality of the final steel slab product....Controlling molten steel flow in the mold and stabilizing the meniscus are critical challenges during the continuous casting,directly impacting the surface quality and internal quality of the final steel slab product.The effects of electromagnetic swirling flow in nozzle(EMSFN)technology on molten steel flow in the mold during slab continuous casting under various casting speeds were investigated.A real-time adjustable EMSFN was developed,and a three-dimensional unsteady Reynolds-averaged Navier–Stokes turbulence mathematical model was established to simulate the flow field within the mold.The results demonstrate that the EMSFN effectively stabilizes the outflow from nozzle,reduces the impact depth and surface velocity of the molten steel,mitigates meniscus fluctuations,and promotes stable flow within the mold.However,a certain matching relationship exists between the casting speed and the current intensity.For the experimental medium-thick slab specifications,the optimal current intensities were found to be 100,130,and 200 A at casting speeds of 1.0,1.5,and 2.0 m/min,respectively.EMSFN can optimize the mold flow field under different casting speeds,providing theoretical support for improving the quality of continuously cast slab products.展开更多
BACKGROUND Intracerebral hemorrhage(ICH)comprises 9%-27%of stroke patients.Hematoma expansion(HE)occurs in approximately 20%of patients following ICH,typically within the first 24 hours.HE increases mortality and long...BACKGROUND Intracerebral hemorrhage(ICH)comprises 9%-27%of stroke patients.Hematoma expansion(HE)occurs in approximately 20%of patients following ICH,typically within the first 24 hours.HE increases mortality and long-term disability in these patients and is being investigated as a therapeutic target to improve the outcome in these patients by limiting HE.Non-contrast computed tomography(NCCT)has potential in predicting HE,which can identify the individuals at risk.AIM To evaluate NCCT markers for predicting HE in patients with ICH and to develop a simple,practical grading system for risk stratification.METHODS This prospective observational study evaluated 192 patients with spontaneous ICH who underwent a baseline NCCT within four hours of admission,followed by a follow-up scan after six hours or earlier if there was clinical deterioration.Hematoma volumes and imaging characteristics that predicted HE were evaluated.A simple five-point grading system score was created to predict HE.In RESULTS Of the 192 patients studied,HE was seen in 106(55.2%).The mean baseline hematoma volume was significantly greater among patients in the HE group(44.1 mL)compared to those in the non-HE group(12.2 mL),with a P-value<0.05.Additionally,imaging biomarkers such as the island sign,swirl sign,and black hole sign were observed with significantly higher frequency in the HE group relative to the non-HE cohort(all P-values<0.05).The island sign was strongly associated with HE[odds ratio(OR)13.7;95%confidence interval(CI):10.15-16.37;P<0.001].Similarly,the black hole sign(OR 9.4;95%CI:7.4-11.62;P<0.001)and the swirl sign(OR 5.2;95%CI:3.72-6.53;P<0.001)emerged as significant predictors of HE.Initial hematoma volume≥30 mL also showed a sig-nificant association(OR 1.9;95%CI:1.41-2.74;P=0.039).A five-point predictive scoring model demonstrated a strong positive association between increasing scores and the probability of HE.Specifically,the likelihood of HE corresponding to scores of 0,1,2,3,4,and 5 was 7.4%,37.5%,75%,85%,93.3%,and 100%,respectively.CONCLUSION The five variables demonstrated statistically significant associations with HE.This simple and practical 5-point prediction score can enable identification of patients at elevated risk of HE based on baseline NCCT findings.This can facilitate timely recognition of high-risk individuals who may benefit from targeted anti-expansion therapy.展开更多
The intake swirl in the cylinder was induced by a swirler which was fixed in one of two intake ports. In order to understand the characteristics of the intake swirl, a transparent water analog was designed which simul...The intake swirl in the cylinder was induced by a swirler which was fixed in one of two intake ports. In order to understand the characteristics of the intake swirl, a transparent water analog was designed which simulated 150 type single cylinder engine. At the same time, the particle image velocimetry was used to measure the flow fields induced by various swirlers in the analog. After measurement, a new method was presented to evaluate the intensity of the intake swirl. Then, when the measured sections, the lifts of valve and the swirlers were different, the calculated results of the flow field were compared.展开更多
The experimental study on the macro and micro characteristics of the spray from a pressure swirl nozzle embraces the growth of surface unstable wave,disintegration process,spray angle,breakup length and so on.The e...The experimental study on the macro and micro characteristics of the spray from a pressure swirl nozzle embraces the growth of surface unstable wave,disintegration process,spray angle,breakup length and so on.The effects of injection pressure,nozzle geometry and liquid properties on these characteristics are also discussed.The results are helpful to understand the underlying physics of the pressure swirl nozzle and serve as the basis for the practical design,usage and improvement of the nozzle.展开更多
Based on the porosity method and the improved non uniform QUICK scheme, this paper describes a three dimensional computer simulation to predict the flow characteristics in a tangentially fired boiler. The model is ap...Based on the porosity method and the improved non uniform QUICK scheme, this paper describes a three dimensional computer simulation to predict the flow characteristics in a tangentially fired boiler. The model is applied to a 600?MW boiler modeling under different operating conditions of reverse swirl of secondary air. The numerical results achieve reasonable agreement with experimental data. The calculated results of flow field, the pressure distribution, the relative diameter of tangential circle, angular momentum flux in furnace and the velocity distribution index in horizontal gas pass are analyzed in detail. And then the effects of the reverse swirl of secondary air on flue gas imbalance are discussed. Finally a reasonable operating condition of the reverse swirl of secondary air is presented.展开更多
In this paper,the spray characteristics of a double-swirl low-emission combustor are analyzed by using Particle Imaging Velocimetry(PIV)and Planar Laser Induced Fluorescence(PLIF)technologies in an optical three-secto...In this paper,the spray characteristics of a double-swirl low-emission combustor are analyzed by using Particle Imaging Velocimetry(PIV)and Planar Laser Induced Fluorescence(PLIF)technologies in an optical three-sector combustor test rig.Interactions between sectors and the influence of main stage swirl intensity on spray structure are explained.The results illustrate that the swirl intensity has great effect on the flow field and spray structure.The spray cone angle is bigger when the swirl number is 0.7,0.9 than that when the swirl number is 0.5.The fuel distribution zone is larger and the distribution is more uniform when the swirl number is 0.5.The fuel concentration in the center area of the center plane of side sector(Plane 5)is larger than that of the center plane of middle sector(Plane 1).The spray cone angle in Plane 5 is larger than that in Plane 1.The width of spray cone becomes larger with the increase of Fuel-Air Ratio(FAR),whereas the spray cone angle under different fuel-air ratios are absolutely the same.The results of the mechanism of spray organization in this study can be used to support the design of new low-emission combustor.展开更多
A new type of dehydration unit for natural gas was briefly described and its basic structure and working principles were presented. An indoor test rig for testing the unit performance was set up and the experimental r...A new type of dehydration unit for natural gas was briefly described and its basic structure and working principles were presented. An indoor test rig for testing the unit performance was set up and the experimental results were given. The results showed that the unit could attain a maximum dew point depression of about 20℃ without any need of external mechanical power and chemicals. The pressure loss ratio, shock wave and the flow rate had great influence on the dehydration characteristics. From the systematic analysis of the factors that affect the dehydration efficiency of the unit, the suggestions for improving the unit are put forward.展开更多
Pressure drop and compound heat transfer characteristics of a converging-diverging tube with evenly spaced twisted-tapes （CD-T tube） have been investigated experimentally. Swirl was generated by evenly spaced twiste...Pressure drop and compound heat transfer characteristics of a converging-diverging tube with evenly spaced twisted-tapes （CD-T tube） have been investigated experimentally. Swirl was generated by evenly spaced twisted-tape elements which vary in twist ratio and rotation angle. Space ratio also has an important effect on the characteristics. For comparison, experiments in a smooth circular tube and a converging-diverging （CD） tube with-out twisted-tapes were carried out. The results show that the twisted-tape with twist ratio y=4.72 and rotation angle θ=180° has the best performance among the four types of twisted-tapes presented in this paper. At Reynolds number ranging from 3400 to 20000, when space ratio s=48.6, the heat transfer efficiency index, which increases as the Reynolds number increases, is 0.85-1.21 and 1.07-1.15 compared to that of a smooth circular tube and a CD tube without twisted-tape inserts, respectively.展开更多
This paper deals with the experimental investigation on Nusselt number,friction factor and thermal en-hancement factor of a double pipe heat exchanger equipped with twisted tape consisting wire nails(WN-TT) and plain ...This paper deals with the experimental investigation on Nusselt number,friction factor and thermal en-hancement factor of a double pipe heat exchanger equipped with twisted tape consisting wire nails(WN-TT) and plain twisted tapes(P-TT) with three different twist ratios of y 2.0,4.4 and 6.0. Test runs are conducted using the water as the working fluid with Reynolds number range between 2000 and 12000 for WN-TT and P-TT. It is found that Nusselt number,friction factor and thermal enhancement factor in the tube equipped with WN-TT appreciably higher than those in the tube fitted with P-TT and plain tube. Over the range considered Nusselt number,friction factor and thermal enhancement factor in a tube with WN-TT are respectively,1.08 to 1.31,1.1 to 1.75 and 1.05 to 1.13 times of those in tube with P-TT. The better performance of WN-TT is due to combined effects of the follow-ing factors:(1) common swirling flow generated by P-TT,(2) additional turbulence offered by the wire nails. Em-pirical correlations for Nusselt number,friction factor and thermal enhancement factor are also formulated from the experimental results of WN-TT and P-TT.展开更多
The atomization dynamic characteristics of a simplex swirl injector was investigated experimentally by using a hydrodynamic mechanical pulsator and the shadow photography technique. The frequency response characterist...The atomization dynamic characteristics of a simplex swirl injector was investigated experimentally by using a hydrodynamic mechanical pulsator and the shadow photography technique. The frequency response characteristics of the fluid film and atomization fluctuations and their correlations with pressure fluctuations were obtained by using an in-house code of image processing. It is demonstrated that the klystron effect induced by periodic pressure fluctuations results in periodic liquid film fluctuation with large amplitudes, periodic superposition of droplets and reduction of the breakup length. It was found that the atomization of the simplex swirl injector only responds to the pressure fluctuation in frequency range approximately from 0 to 300 Hz, and it is particularly sensitive to pressure fluctuations at frequencies from 100 to 200 Hz. According to this experiment, the responsive frequency limitation is merely affected by injector configuration, rather than the supply line.展开更多
The mechanism of inclusion aggregation in liquid steel in swirling flow tundish is analyzed by applying the theory of flocculation which was developed in the field of colloid engineering. The gas bridge forces due to ...The mechanism of inclusion aggregation in liquid steel in swirling flow tundish is analyzed by applying the theory of flocculation which was developed in the field of colloid engineering. The gas bridge forces due to the micro bubbles on hydrophobic inclusion surfaces were responsible for the inclusion collision and agglomeration, which can avoid the aggregation to breakup. The quantity of micro bubbles on hydrophobic inclusion particle is more than that on hydrophilic one. The trend of forming gas bridges between micro bubbles on particles is strong in the course of collision. The liquid film on hydrophobic particles is easy to break during collision process. Hydrophobic particles are liable to aggregate in collision. According to the analysis of forces on a nonmetallic inclusion particle in swirling chamber, the chance of inclusion collision and aggregation can be improved by the centripetal force. Hydropbobic particles in water are liable to aggregate in collision. Hydrophilic particles in water are dispersed although collision happens. The wettability can be changed by changing solid-liquid interface tension. The nonmetallic inclusion removal in swirling flow tundish is studied. The result shows that under certain turbulent conditions, the.particle concentration and the wettability between particles and liquid steel are the main factors to induce collision and aggregation.展开更多
The supersonic nozzle is a new apparatus which can be used to condense and separate water and heavy hydrocarbons from natural gas.The swirling separation of natural gas in the convergent-divergent nozzle was numerical...The supersonic nozzle is a new apparatus which can be used to condense and separate water and heavy hydrocarbons from natural gas.The swirling separation of natural gas in the convergent-divergent nozzle was numerically simulated based on a new design which incorporates a central body. Axial distribution of the main parameters of gas flow was investigated,while the basic parameters of gas flow were obtained as functions of radius at the nozzle exit.The effect of the nozzle geometry on the swirling separation was analyzed.The numerical results show that water and heavy hydrocarbons can be condensed and separated from natural gas under the combined effect of the low temperature（-80℃） and the centrifugal field（482,400g,g is the acceleration of gravity）.The gas dynamic parameters are uniformly distributed correspondingly in the radial central region of the channel,for example the distribution range of the static temperature and the centrifugal acceleration are from -80 to -55℃and 220,000g to 500,000g,respectively,which would create good conditions for the cyclone separation of the liquids.However,high gradients of gas dynamic parameters near the channel walls may impair the process of separation.The geometry of the nozzle has a great influence on the separation performance. Increasing the nozzle convergent angle can improve the separation efficiency.The swirling natural gas can be well separated when the divergent angle takes values from 4°to 12°in the convergent-divergent nozzle.展开更多
A conventional turbulence inhibitor is compared with a swirling chamber from the points of view of fluid flow and removal rate of inclusion in the tundish. Comparing the RTD curves, inclusion removals, and the streaml...A conventional turbulence inhibitor is compared with a swirling chamber from the points of view of fluid flow and removal rate of inclusion in the tundish. Comparing the RTD curves, inclusion removals, and the streamlines in water model experiments, it can be found that the tundish equipped with a swirling chamber has a great effect on improving the flow field, and the floatation rate of inclusion is higher than the tundish with a turbulence inhibitor. Because of the introduction of the swirling chamber, the flow field and inclusion removal in a two-strand swirling flow tundish are asymmetrical. Rotating the inlet direction of swirling chamber 60 degree is a good strategy to improve the asymmetrical flow field.展开更多
This paper presents an experimental study on the emission characteristics and combustion instabilities of oxy-fuel combustions in a swirl-stabilized combustor. Different oxygen concentrations (Xoxy=25%～45%, where Xox...This paper presents an experimental study on the emission characteristics and combustion instabilities of oxy-fuel combustions in a swirl-stabilized combustor. Different oxygen concentrations (Xoxy=25%～45%, where Xoxy is oxygen concentra- tion by volume), equivalence ratios (φ=0.75～1.15) and combustion powers (CP=1.08～2.02 kW) were investigated in the oxy-fuel (CH4/CO2/O2) combustions, and reference cases (Xoxy=25%～35%, CH4/N2/O2 flames) were covered. The results show that the oxygen concentration in the oxidant stream significantly affects the combustion delay in the oxy-fuel flames, and the equivalence ratio has a slight effect, whereas the combustion power shows no impact. The temperature levels of the oxy-fuel flames inside the combustion chamber are much higher (up to 38.7%) than those of the reference cases. Carbon monoxide was vastly produced when Xoxy>35% or φ>0.95 in the oxy-fuel flames, while no nitric oxide was found in the exhaust gases because no N2 participates in the combustion process. The combustion instability of the oxy-fuel combustion is very different from those of the reference cases with similar oxygen content. Oxy-fuel combustions excite strong oscillations in all cases studied Xoxy=25%～45%. However, no pressure fluctuations were detected in the reference cases when Xoxy>28.6% accomplished by heavily sooting flames which were not found in the oxy-fuel combustions. Spectrum analysis shows that the frequency of dynamic pressure oscillations exhibits randomness in the range of 50～250 Hz, therefore resulting in a very small resultant amplitude. Temporal oscillations are very strong with amplitudes larger than 200 Pa, even short time fast Fourier transform (FFT) analysis (0.08 s) shows that the pressure amplitude can be larger than 40 Pa.展开更多
The gas-liquid two-phase swirl flow can increase the gas-liquid two-phase contact area and enhance the heat and mass transfer efficiency between gas and liquid.The swirl flow has important practical application value ...The gas-liquid two-phase swirl flow can increase the gas-liquid two-phase contact area and enhance the heat and mass transfer efficiency between gas and liquid.The swirl flow has important practical application value for promoting gas hydrate formation and ensuring the flow safe of natural gas hydrate slurry.The experimental section was made of plexiglass pipe and the experimental medium was air and water.The flow pattern of the gas-liquid two-phase swirl flow in the horizontal pipe was divided,according to a high-definition camera and the overall characteristics of the gas-liquid interface.The flow pattern map of the gas-liquid two-phase swirl flow in a horizontal pipe was studied.The influence of the flow velocity and vane parameters on pressure drop was investigated.Two types of gas-liquid two-phase swirl flow pressure drop models was established.The homogeneous-phase and split-phase pressure drop models have good prediction on swirl bubble flow,swirl dispersed flow,swirl annular flow and swirl stratified flow,and the predictive error band is not more than 20%.展开更多
基金supported by the National Natural Science Foundation of China(Nos.52306035 and 52325602)the Science Center for Gas Turbine Project,China(Nos.P2022-A-II-002-001 and P2022-C-II-003-001)+1 种基金the National Science and Technology Major Project,China(Nos.Y2022-II-0002-0005 and Y2022-II-0003-0006)the Key Laboratory of Pre-Research Management Centre,China(No.6142702200101)。
文摘An experimental investigation is conducted to evaluate the performance and the stalling process of a fan subjected to inlet swirls,as well as the effectiveness of an Impedance Boundary-Controlled(IBC)Casing Treatment(CT)on the stall margin recovery.An operating cycle is proposed based on the hysteresis effect of harmonic flap oscillation of airfoils and parallel compressor theory to explain the pressure characteristic of the fan under twin swirl inlets.Twin swirls are observed to reduce the stall margin of the fan,and the circumferential location where the spike is detected turns to the intersection area of the twin swirl.The IBC CT is proven to extend the stall margin of the fan for 12.7%–22.3%when subjected to inlet swirls with an efficiency loss of around 1%.The IBC CT helps to reduce the size of the operating cycle of the fan by redistributing the blade loading and adding the system damping to dissipate the perturbation energy.
文摘Aim To obtain an optimizing range of the main configuration parameters of double swirls combustion system (DSCS) Methods To analyze the influence of DS combustion cham-ber configuration parameters on fuel spray and mixing by means of the fuel jet developmentperiphery charts obtained by the high speed photography with a modeling test device deve-loped by authors,and to examine it by the tests on a single cylinder diesel engine.Resultsand Conclusion The mixing process can be divided into four phases.The optimizing range of the ration of the inner chamber diameter to the cylinder bore,d2/D,is 0.4-0.7; and the outerchamber diameter,d1 the height of the circular ridge to the piston top face,h1,the radius of outer/inner chamber circle,R1,R2 ,the max depth of outer/inner chamber bowl,H1,H2,etc. are also important
基金support of the Fundamental Research Funds for the Central Universities(No.E2ET0411X2).
文摘In recent years,research investigations have focused on the substantial freshwater storage in the Beaufort Gyre(BG)region due to climate change.Despite active mesoscale eddies in the area,a notable gap in understanding the three-dimensional structure and induced transport has been observed.This study concentrates on the Canada Basin in the western Arctic Ocean,specifically examining a subsurface anticyclonic eddy(SAE)sampled by a Mooring A in the BG region.Hybrid Coordinate Ocean Model(HYCOM)analysis data reveal its lifecycle from February 15 to March 15,2017,marked by initiation,development,maturity,decay,and termination stages.This work extends the finding of SAE passing through Mooring A by examining its overall effects,spatiotemporal variations,and swirl transport.SAE generation through baroclinic instability,which contributes to the westward tilt of the vertical axis,is also confirmed in this study.Swirl transport induced by SAE is predominantly eastward and downward due to its trajectory and background flow.SAE temporarily weakens stratification and extends the subsurface depth but demonstrates transient effects.Moreover,SAE transports upper-layer freshwater,Pacific Winter Water,and Atlantic Water downward,emphasizing its potential influence on freshwater redistribution in the Canadian Basin.This research provides valuable insights into mesoscale eddy dynamics,revealing their role in modulating the upper water mass in the BG region.
基金supported by the Application Technology of Automotive Steels(No.2021040300048)the National Natural Science Foundation of China(No.52304347)+2 种基金Hebei Provincial Natural Science Foundation(No.E2019501008),China Baowu Low Carbon Metallurgy Innovation Foundation(BWLCF202320)Natural Science Foundation of Liaoning Province(Nos.2023-MSBA-135 and 2023-BSBA-107)Fundamental Research Funds for the Central Universities(Nos.N2409008 and N2409006).
文摘The electromagnetic swirling flow in nozzle(EMSFN)technique is designed to mitigate the adverse effects of unstable and uneven flow within the submerged entry nozzle in continuous casting.Utilizing electromagnetic forces,EMSFN stabilizes the flow within the nozzle,leading to a more controlled flow in the mold.Numerical simulations were used to quantitatively analyze the magnetic and flow fields in a slab continuous casting system under EMSFN.Results indicate that EMSFN significantly stabilizes the outflow from the nozzle,with stability increasing with higher current intensity.At 10,000 Ampere-turns(At)of the coil,meniscus fluctuations were unstable.They stabilized at 13,000 At,with minimal changes observed beyond this point.The optimal current intensity for stable mold flow,at a casting speed of 1.56 m/min,is 13,000 At.These findings confirm the effectiveness of EMSFN in stabilizing the internal flow field of the slab mold and determining optimal operational current intensity.
基金National Natural Science Foundation of China(Nos.U21A20117,52104347 and 52272078)the Fundamental Research Funds for the Central Universities(No.N2409006)Natural Science Foundation of Liaoning Province(2023-MSBA-135)for the financial support.
文摘Controlling molten steel flow in the mold and stabilizing the meniscus are critical challenges during the continuous casting,directly impacting the surface quality and internal quality of the final steel slab product.The effects of electromagnetic swirling flow in nozzle(EMSFN)technology on molten steel flow in the mold during slab continuous casting under various casting speeds were investigated.A real-time adjustable EMSFN was developed,and a three-dimensional unsteady Reynolds-averaged Navier–Stokes turbulence mathematical model was established to simulate the flow field within the mold.The results demonstrate that the EMSFN effectively stabilizes the outflow from nozzle,reduces the impact depth and surface velocity of the molten steel,mitigates meniscus fluctuations,and promotes stable flow within the mold.However,a certain matching relationship exists between the casting speed and the current intensity.For the experimental medium-thick slab specifications,the optimal current intensities were found to be 100,130,and 200 A at casting speeds of 1.0,1.5,and 2.0 m/min,respectively.EMSFN can optimize the mold flow field under different casting speeds,providing theoretical support for improving the quality of continuously cast slab products.
文摘BACKGROUND Intracerebral hemorrhage(ICH)comprises 9%-27%of stroke patients.Hematoma expansion(HE)occurs in approximately 20%of patients following ICH,typically within the first 24 hours.HE increases mortality and long-term disability in these patients and is being investigated as a therapeutic target to improve the outcome in these patients by limiting HE.Non-contrast computed tomography(NCCT)has potential in predicting HE,which can identify the individuals at risk.AIM To evaluate NCCT markers for predicting HE in patients with ICH and to develop a simple,practical grading system for risk stratification.METHODS This prospective observational study evaluated 192 patients with spontaneous ICH who underwent a baseline NCCT within four hours of admission,followed by a follow-up scan after six hours or earlier if there was clinical deterioration.Hematoma volumes and imaging characteristics that predicted HE were evaluated.A simple five-point grading system score was created to predict HE.In RESULTS Of the 192 patients studied,HE was seen in 106(55.2%).The mean baseline hematoma volume was significantly greater among patients in the HE group(44.1 mL)compared to those in the non-HE group(12.2 mL),with a P-value<0.05.Additionally,imaging biomarkers such as the island sign,swirl sign,and black hole sign were observed with significantly higher frequency in the HE group relative to the non-HE cohort(all P-values<0.05).The island sign was strongly associated with HE[odds ratio(OR)13.7;95%confidence interval(CI):10.15-16.37;P<0.001].Similarly,the black hole sign(OR 9.4;95%CI:7.4-11.62;P<0.001)and the swirl sign(OR 5.2;95%CI:3.72-6.53;P<0.001)emerged as significant predictors of HE.Initial hematoma volume≥30 mL also showed a sig-nificant association(OR 1.9;95%CI:1.41-2.74;P=0.039).A five-point predictive scoring model demonstrated a strong positive association between increasing scores and the probability of HE.Specifically,the likelihood of HE corresponding to scores of 0,1,2,3,4,and 5 was 7.4%,37.5%,75%,85%,93.3%,and 100%,respectively.CONCLUSION The five variables demonstrated statistically significant associations with HE.This simple and practical 5-point prediction score can enable identification of patients at elevated risk of HE based on baseline NCCT findings.This can facilitate timely recognition of high-risk individuals who may benefit from targeted anti-expansion therapy.
文摘The intake swirl in the cylinder was induced by a swirler which was fixed in one of two intake ports. In order to understand the characteristics of the intake swirl, a transparent water analog was designed which simulated 150 type single cylinder engine. At the same time, the particle image velocimetry was used to measure the flow fields induced by various swirlers in the analog. After measurement, a new method was presented to evaluate the intensity of the intake swirl. Then, when the measured sections, the lifts of valve and the swirlers were different, the calculated results of the flow field were compared.
文摘The experimental study on the macro and micro characteristics of the spray from a pressure swirl nozzle embraces the growth of surface unstable wave,disintegration process,spray angle,breakup length and so on.The effects of injection pressure,nozzle geometry and liquid properties on these characteristics are also discussed.The results are helpful to understand the underlying physics of the pressure swirl nozzle and serve as the basis for the practical design,usage and improvement of the nozzle.
文摘Based on the porosity method and the improved non uniform QUICK scheme, this paper describes a three dimensional computer simulation to predict the flow characteristics in a tangentially fired boiler. The model is applied to a 600?MW boiler modeling under different operating conditions of reverse swirl of secondary air. The numerical results achieve reasonable agreement with experimental data. The calculated results of flow field, the pressure distribution, the relative diameter of tangential circle, angular momentum flux in furnace and the velocity distribution index in horizontal gas pass are analyzed in detail. And then the effects of the reverse swirl of secondary air on flue gas imbalance are discussed. Finally a reasonable operating condition of the reverse swirl of secondary air is presented.
基金supported by the National Natural Science Foundation of China(Nos.51306182 and 51406202).
文摘In this paper,the spray characteristics of a double-swirl low-emission combustor are analyzed by using Particle Imaging Velocimetry(PIV)and Planar Laser Induced Fluorescence(PLIF)technologies in an optical three-sector combustor test rig.Interactions between sectors and the influence of main stage swirl intensity on spray structure are explained.The results illustrate that the swirl intensity has great effect on the flow field and spray structure.The spray cone angle is bigger when the swirl number is 0.7,0.9 than that when the swirl number is 0.5.The fuel distribution zone is larger and the distribution is more uniform when the swirl number is 0.5.The fuel concentration in the center area of the center plane of side sector(Plane 5)is larger than that of the center plane of middle sector(Plane 1).The spray cone angle in Plane 5 is larger than that in Plane 1.The width of spray cone becomes larger with the increase of Fuel-Air Ratio(FAR),whereas the spray cone angle under different fuel-air ratios are absolutely the same.The results of the mechanism of spray organization in this study can be used to support the design of new low-emission combustor.
文摘A new type of dehydration unit for natural gas was briefly described and its basic structure and working principles were presented. An indoor test rig for testing the unit performance was set up and the experimental results were given. The results showed that the unit could attain a maximum dew point depression of about 20℃ without any need of external mechanical power and chemicals. The pressure loss ratio, shock wave and the flow rate had great influence on the dehydration characteristics. From the systematic analysis of the factors that affect the dehydration efficiency of the unit, the suggestions for improving the unit are put forward.
基金Supported by the State Key Development Program for Basic Research of China （No.G2000263001） and the National Natural Science Foundation of China （No.20776046）.
文摘Pressure drop and compound heat transfer characteristics of a converging-diverging tube with evenly spaced twisted-tapes （CD-T tube） have been investigated experimentally. Swirl was generated by evenly spaced twisted-tape elements which vary in twist ratio and rotation angle. Space ratio also has an important effect on the characteristics. For comparison, experiments in a smooth circular tube and a converging-diverging （CD） tube with-out twisted-tapes were carried out. The results show that the twisted-tape with twist ratio y=4.72 and rotation angle θ=180° has the best performance among the four types of twisted-tapes presented in this paper. At Reynolds number ranging from 3400 to 20000, when space ratio s=48.6, the heat transfer efficiency index, which increases as the Reynolds number increases, is 0.85-1.21 and 1.07-1.15 compared to that of a smooth circular tube and a CD tube without twisted-tape inserts, respectively.
文摘This paper deals with the experimental investigation on Nusselt number,friction factor and thermal en-hancement factor of a double pipe heat exchanger equipped with twisted tape consisting wire nails(WN-TT) and plain twisted tapes(P-TT) with three different twist ratios of y 2.0,4.4 and 6.0. Test runs are conducted using the water as the working fluid with Reynolds number range between 2000 and 12000 for WN-TT and P-TT. It is found that Nusselt number,friction factor and thermal enhancement factor in the tube equipped with WN-TT appreciably higher than those in the tube fitted with P-TT and plain tube. Over the range considered Nusselt number,friction factor and thermal enhancement factor in a tube with WN-TT are respectively,1.08 to 1.31,1.1 to 1.75 and 1.05 to 1.13 times of those in tube with P-TT. The better performance of WN-TT is due to combined effects of the follow-ing factors:(1) common swirling flow generated by P-TT,(2) additional turbulence offered by the wire nails. Em-pirical correlations for Nusselt number,friction factor and thermal enhancement factor are also formulated from the experimental results of WN-TT and P-TT.
基金supported by the National Natural Science Foundation of China(Nos.11502186 and 51606138)the National Key Basic Research Program of China(973 Program)and National Key Scientific Instrumentthe Equipment Development Projects of China(No.2012YQ04016408)
文摘The atomization dynamic characteristics of a simplex swirl injector was investigated experimentally by using a hydrodynamic mechanical pulsator and the shadow photography technique. The frequency response characteristics of the fluid film and atomization fluctuations and their correlations with pressure fluctuations were obtained by using an in-house code of image processing. It is demonstrated that the klystron effect induced by periodic pressure fluctuations results in periodic liquid film fluctuation with large amplitudes, periodic superposition of droplets and reduction of the breakup length. It was found that the atomization of the simplex swirl injector only responds to the pressure fluctuation in frequency range approximately from 0 to 300 Hz, and it is particularly sensitive to pressure fluctuations at frequencies from 100 to 200 Hz. According to this experiment, the responsive frequency limitation is merely affected by injector configuration, rather than the supply line.
文摘The mechanism of inclusion aggregation in liquid steel in swirling flow tundish is analyzed by applying the theory of flocculation which was developed in the field of colloid engineering. The gas bridge forces due to the micro bubbles on hydrophobic inclusion surfaces were responsible for the inclusion collision and agglomeration, which can avoid the aggregation to breakup. The quantity of micro bubbles on hydrophobic inclusion particle is more than that on hydrophilic one. The trend of forming gas bridges between micro bubbles on particles is strong in the course of collision. The liquid film on hydrophobic particles is easy to break during collision process. Hydrophobic particles are liable to aggregate in collision. According to the analysis of forces on a nonmetallic inclusion particle in swirling chamber, the chance of inclusion collision and aggregation can be improved by the centripetal force. Hydropbobic particles in water are liable to aggregate in collision. Hydrophilic particles in water are dispersed although collision happens. The wettability can be changed by changing solid-liquid interface tension. The nonmetallic inclusion removal in swirling flow tundish is studied. The result shows that under certain turbulent conditions, the.particle concentration and the wettability between particles and liquid steel are the main factors to induce collision and aggregation.
基金supported by the National High Technology Research and Development Program of China("863 program",No.2007AA09Z301) the National Major Science&Technology Specific Projects(No.2008ZX05017-004)
文摘The supersonic nozzle is a new apparatus which can be used to condense and separate water and heavy hydrocarbons from natural gas.The swirling separation of natural gas in the convergent-divergent nozzle was numerically simulated based on a new design which incorporates a central body. Axial distribution of the main parameters of gas flow was investigated,while the basic parameters of gas flow were obtained as functions of radius at the nozzle exit.The effect of the nozzle geometry on the swirling separation was analyzed.The numerical results show that water and heavy hydrocarbons can be condensed and separated from natural gas under the combined effect of the low temperature（-80℃） and the centrifugal field（482,400g,g is the acceleration of gravity）.The gas dynamic parameters are uniformly distributed correspondingly in the radial central region of the channel,for example the distribution range of the static temperature and the centrifugal acceleration are from -80 to -55℃and 220,000g to 500,000g,respectively,which would create good conditions for the cyclone separation of the liquids.However,high gradients of gas dynamic parameters near the channel walls may impair the process of separation.The geometry of the nozzle has a great influence on the separation performance. Increasing the nozzle convergent angle can improve the separation efficiency.The swirling natural gas can be well separated when the divergent angle takes values from 4°to 12°in the convergent-divergent nozzle.
文摘A conventional turbulence inhibitor is compared with a swirling chamber from the points of view of fluid flow and removal rate of inclusion in the tundish. Comparing the RTD curves, inclusion removals, and the streamlines in water model experiments, it can be found that the tundish equipped with a swirling chamber has a great effect on improving the flow field, and the floatation rate of inclusion is higher than the tundish with a turbulence inhibitor. Because of the introduction of the swirling chamber, the flow field and inclusion removal in a two-strand swirling flow tundish are asymmetrical. Rotating the inlet direction of swirling chamber 60 degree is a good strategy to improve the asymmetrical flow field.
基金Project supported by the National Natural Science Foundation of China (No. 50576081)Zhejiang Provincial Natural Science Foundation of China (No. R107532)+1 种基金Program for the New Century Excellent Talents in University (No. NCET-07-0761)the Foundation for the Author of National Excellent Doctoral Dissertation of China (No. 200747)
文摘This paper presents an experimental study on the emission characteristics and combustion instabilities of oxy-fuel combustions in a swirl-stabilized combustor. Different oxygen concentrations (Xoxy=25%～45%, where Xoxy is oxygen concentra- tion by volume), equivalence ratios (φ=0.75～1.15) and combustion powers (CP=1.08～2.02 kW) were investigated in the oxy-fuel (CH4/CO2/O2) combustions, and reference cases (Xoxy=25%～35%, CH4/N2/O2 flames) were covered. The results show that the oxygen concentration in the oxidant stream significantly affects the combustion delay in the oxy-fuel flames, and the equivalence ratio has a slight effect, whereas the combustion power shows no impact. The temperature levels of the oxy-fuel flames inside the combustion chamber are much higher (up to 38.7%) than those of the reference cases. Carbon monoxide was vastly produced when Xoxy>35% or φ>0.95 in the oxy-fuel flames, while no nitric oxide was found in the exhaust gases because no N2 participates in the combustion process. The combustion instability of the oxy-fuel combustion is very different from those of the reference cases with similar oxygen content. Oxy-fuel combustions excite strong oscillations in all cases studied Xoxy=25%～45%. However, no pressure fluctuations were detected in the reference cases when Xoxy>28.6% accomplished by heavily sooting flames which were not found in the oxy-fuel combustions. Spectrum analysis shows that the frequency of dynamic pressure oscillations exhibits randomness in the range of 50～250 Hz, therefore resulting in a very small resultant amplitude. Temporal oscillations are very strong with amplitudes larger than 200 Pa, even short time fast Fourier transform (FFT) analysis (0.08 s) shows that the pressure amplitude can be larger than 40 Pa.
基金Project(51574045)supported by the National Nature Science Foundation of China
文摘The gas-liquid two-phase swirl flow can increase the gas-liquid two-phase contact area and enhance the heat and mass transfer efficiency between gas and liquid.The swirl flow has important practical application value for promoting gas hydrate formation and ensuring the flow safe of natural gas hydrate slurry.The experimental section was made of plexiglass pipe and the experimental medium was air and water.The flow pattern of the gas-liquid two-phase swirl flow in the horizontal pipe was divided,according to a high-definition camera and the overall characteristics of the gas-liquid interface.The flow pattern map of the gas-liquid two-phase swirl flow in a horizontal pipe was studied.The influence of the flow velocity and vane parameters on pressure drop was investigated.Two types of gas-liquid two-phase swirl flow pressure drop models was established.The homogeneous-phase and split-phase pressure drop models have good prediction on swirl bubble flow,swirl dispersed flow,swirl annular flow and swirl stratified flow,and the predictive error band is not more than 20%.
