Using molten Pb-Sn-Bi alloy, the meniscus shape under high frequency magnetic field of φ100 mm round billet caster was investigated. The effect of some parameters on meniscus shape was studied. The results show that ...Using molten Pb-Sn-Bi alloy, the meniscus shape under high frequency magnetic field of φ100 mm round billet caster was investigated. The effect of some parameters on meniscus shape was studied. The results show that for a mold with 12 segments, the meniscus shape is relatively stable. With increasing power input, the menis- cus height increases with intensification of fluctuation. For the given caster, the reasonable power input is about 70 kW. The coil should be near to the top of mold and/or the initial meniscus should be near to the center of the coil. The lower the frequency, the higher is the meniscus height. With increasing frequency, the free surface is more flattened and meniscus becomes more stable. In practice, the power input should be increased simultaneously with frequency. The optimal frequency is about 20 kHz.展开更多
To design a power source system and mold for electromagnetic soft-contact continuous casting process and to theoretically estimate the heat losses from the charges and the system power, the effect of structure paramet...To design a power source system and mold for electromagnetic soft-contact continuous casting process and to theoretically estimate the heat losses from the charges and the system power, the effect of structure parameters on system power and magnetic flux density distribution was calculated using finite element method. The results show that as for electromagnetic soft-contact continuous casting system with partial-segment type mold, the power consumption is much more than that with a full-segment type mold; about 62% of electric power is dissipated in the mold, and the effective acting range of magnetic field is relatively narrow. Optimizing mold structure is a crucial measure of remarkably reducing mold power consumption and saving electric energy. Increasing slit number, width, and length can remarkably increase the magnetic flux density in the mold and can reduce the electric energy consumption. Among structure parameters, slit number and slit width are relatively more effective to reduce energy consumption. For a round billet electromagnetic continuous casting system with diameter of 178 ram, the reasonable slit number, width, and length are about 24--32, 0. 5--1.0 mm, and 160 mm, respectively.展开更多
In this paper, coupling the quasi-3D numerical simulation of electromagnetic field and the experiments of continuous casting with soft-contacted mould with some metals such as tin, aluminum, copper and steel, the elec...In this paper, coupling the quasi-3D numerical simulation of electromagnetic field and the experiments of continuous casting with soft-contacted mould with some metals such as tin, aluminum, copper and steel, the electromagnetic characteristics of continuous casting with soft-contacted mould is analyzed. It is shown that the electromagnetic pressure on the surface of billet is increasing with the rising of power frequency as a logarithmically parabolic function, with that of electric conductivity of billet as a power junction, and with that of the current in inductor as a parabolic junction.展开更多
The paper introduces the research and new development on soft-contacting electromagnetic continuous casting in Baosteel.At the year of 2008,Baosteel successfully completed the carbon steel SCEMCC industrial experiment...The paper introduces the research and new development on soft-contacting electromagnetic continuous casting in Baosteel.At the year of 2008,Baosteel successfully completed the carbon steel SCEMCC industrial experiment in a 6-strand curved type round billet caster.At the year of 2011,Baosteel selected another 3-strand curved billet caster. Baosteel successfully developed the SCEMCC mold for the first time to do the industrial production experiment for stainless steel round billet continuous casting.Then,in the same stainless steel caster,the square billet SCEMCC mold was successfully developed too.And at the beginning of the year 2012,the square billet SCEMCC of SUS304 and SUS303Cu was implemented up to now.It was proved the machine system was reliable for the long time production.The industrial experimental result shows the soft-contacting electromagnetic continuous casting can reduce the depth of oscillation mark from about 0.7mm to near zero.The SCEMCC billets without surface grinding were transferred to mill tubes,of which the quality is satisfied.展开更多
A two-dimensional axisymmetric finite element model for stress distribution of billet in electromagnetic soft-contact continuous casting mould was established by a two-way coupled method.The contact state between soli...A two-dimensional axisymmetric finite element model for stress distribution of billet in electromagnetic soft-contact continuous casting mould was established by a two-way coupled method.The contact state between solidified shell and mould was described to simulate the thermal-mechanical behaviors in the soft-contact mould.And the effects of frequencies and currents on stress distribution of billet had been discussed and analyzed.The results show that the equivalent stress of initial solidification shell both at its outer and inner surface decreases but at the bottom the equivalent stress of two sides of shell both increases when the current intensity is 1600 A,and the frequency is 20 kHz,compared with the status of conventional continuous casting.展开更多
Coupling the quasi 3D numerical simulation of electromagnetic field and the experiments with some metals such as tin, aluminum, copper and steel, the electromagnetic characteristics of continuous casting with soft con...Coupling the quasi 3D numerical simulation of electromagnetic field and the experiments with some metals such as tin, aluminum, copper and steel, the electromagnetic characteristics of continuous casting with soft contacted mould, especially the influences of power frequency, the mould structure, and the inductor position, size and current on the electromagnetic force and pressure on the billet, were analyzed. The result shows that, in continuous casting with soft contacted mould, the electromagnetic pressure on the surface of billet increases with the rising of the power frequency as a logarithmically parabolic function and, with that of inductor current as a parabolic function. The design principle of the soft contacted mould is that 1) the mould structure should be ‘more segments and thin slits’; 2) the topside of inductor should be at the same location with the meniscus of molten metal; 3) the inductor should cover the initial solidifying shell of billet.展开更多
Coupling the quasi 3D numerical simulation of the electromagnetic field and the experiments with some metals, a series of phenomena in the processes of continuous casting with soft contacted mould was analyzed. Some t...Coupling the quasi 3D numerical simulation of the electromagnetic field and the experiments with some metals, a series of phenomena in the processes of continuous casting with soft contacted mould was analyzed. Some theoretical and experimental models were presented, from which following results were obtained. 1) The electromagnetic force is related with electric conductivity of billet as a power function to 0.4. 2) The heat transfer between billet and mould is related with the contacting pressure, and it is a linear function for tin billet approximately. 3) The distance between initial solidification point and meniscus in billet is related with the surface magnetic flux density as a fourth root function. 4) The temperature gradient in the initial solidifying shell is reduced, which can decrease the tendency of hot tearing on the surface of billet, and increase the equiaxed crystal zone in billet. 5) The stronger the magnetic flux density is, the more shallow and the thinner the oscillation mark on the surface of billet is. 6) The depth of oscillation mark on the billet cast by the soft contacted mould can be reduced to about 10% in comparison with that on the billets cast by traditional mould. 7) In non dimensional condition, the average depth of the oscillation marks on the billets cast by the soft contacted mould decreases with increasing magnetic flux density on there as a complementary error function. [展开更多
The distribution of the magnetic flux density in a soft-contact electromagnetic continuous casting （EMCC） rectangular mold was investigated. The experimental results show that with an increase in electric power, the...The distribution of the magnetic flux density in a soft-contact electromagnetic continuous casting （EMCC） rectangular mold was investigated. The experimental results show that with an increase in electric power, the magnetic flux density increases. The position where the maximum magnetic flux density appears will shift up when the coil moves to the top of the mold. At the same time, the maximum magnetic flux density will increase and the effective acting range of electromagnetic pressure will widen. As a result, in practice, the coil should be placed near the top part of the mold. The meniscus should be controlled near the top part of the coil, as this not only remarkably improves the billet surface quality but also saves energy. With the same electric power input, the higher the frequency, the lower the magnetic flux density.展开更多
文摘Using molten Pb-Sn-Bi alloy, the meniscus shape under high frequency magnetic field of φ100 mm round billet caster was investigated. The effect of some parameters on meniscus shape was studied. The results show that for a mold with 12 segments, the meniscus shape is relatively stable. With increasing power input, the menis- cus height increases with intensification of fluctuation. For the given caster, the reasonable power input is about 70 kW. The coil should be near to the top of mold and/or the initial meniscus should be near to the center of the coil. The lower the frequency, the higher is the meniscus height. With increasing frequency, the free surface is more flattened and meniscus becomes more stable. In practice, the power input should be increased simultaneously with frequency. The optimal frequency is about 20 kHz.
基金Item Sponsored by National Natural Science Foundation of China(50274203)National High Technology Research and Development Program of China(2001AA337040)
文摘To design a power source system and mold for electromagnetic soft-contact continuous casting process and to theoretically estimate the heat losses from the charges and the system power, the effect of structure parameters on system power and magnetic flux density distribution was calculated using finite element method. The results show that as for electromagnetic soft-contact continuous casting system with partial-segment type mold, the power consumption is much more than that with a full-segment type mold; about 62% of electric power is dissipated in the mold, and the effective acting range of magnetic field is relatively narrow. Optimizing mold structure is a crucial measure of remarkably reducing mold power consumption and saving electric energy. Increasing slit number, width, and length can remarkably increase the magnetic flux density in the mold and can reduce the electric energy consumption. Among structure parameters, slit number and slit width are relatively more effective to reduce energy consumption. For a round billet electromagnetic continuous casting system with diameter of 178 ram, the reasonable slit number, width, and length are about 24--32, 0. 5--1.0 mm, and 160 mm, respectively.
文摘In this paper, coupling the quasi-3D numerical simulation of electromagnetic field and the experiments of continuous casting with soft-contacted mould with some metals such as tin, aluminum, copper and steel, the electromagnetic characteristics of continuous casting with soft-contacted mould is analyzed. It is shown that the electromagnetic pressure on the surface of billet is increasing with the rising of power frequency as a logarithmically parabolic function, with that of electric conductivity of billet as a power junction, and with that of the current in inductor as a parabolic junction.
文摘The paper introduces the research and new development on soft-contacting electromagnetic continuous casting in Baosteel.At the year of 2008,Baosteel successfully completed the carbon steel SCEMCC industrial experiment in a 6-strand curved type round billet caster.At the year of 2011,Baosteel selected another 3-strand curved billet caster. Baosteel successfully developed the SCEMCC mold for the first time to do the industrial production experiment for stainless steel round billet continuous casting.Then,in the same stainless steel caster,the square billet SCEMCC mold was successfully developed too.And at the beginning of the year 2012,the square billet SCEMCC of SUS304 and SUS303Cu was implemented up to now.It was proved the machine system was reliable for the long time production.The industrial experimental result shows the soft-contacting electromagnetic continuous casting can reduce the depth of oscillation mark from about 0.7mm to near zero.The SCEMCC billets without surface grinding were transferred to mill tubes,of which the quality is satisfied.
基金Item Sponsored by National Natural Science Foundation of China[No.50834009]Key Grant Project of China Ministry of Education (No.311014)
文摘A two-dimensional axisymmetric finite element model for stress distribution of billet in electromagnetic soft-contact continuous casting mould was established by a two-way coupled method.The contact state between solidified shell and mould was described to simulate the thermal-mechanical behaviors in the soft-contact mould.And the effects of frequencies and currents on stress distribution of billet had been discussed and analyzed.The results show that the equivalent stress of initial solidification shell both at its outer and inner surface decreases but at the bottom the equivalent stress of two sides of shell both increases when the current intensity is 1600 A,and the frequency is 20 kHz,compared with the status of conventional continuous casting.
文摘Coupling the quasi 3D numerical simulation of electromagnetic field and the experiments with some metals such as tin, aluminum, copper and steel, the electromagnetic characteristics of continuous casting with soft contacted mould, especially the influences of power frequency, the mould structure, and the inductor position, size and current on the electromagnetic force and pressure on the billet, were analyzed. The result shows that, in continuous casting with soft contacted mould, the electromagnetic pressure on the surface of billet increases with the rising of the power frequency as a logarithmically parabolic function and, with that of inductor current as a parabolic function. The design principle of the soft contacted mould is that 1) the mould structure should be ‘more segments and thin slits’; 2) the topside of inductor should be at the same location with the meniscus of molten metal; 3) the inductor should cover the initial solidifying shell of billet.
文摘Coupling the quasi 3D numerical simulation of the electromagnetic field and the experiments with some metals, a series of phenomena in the processes of continuous casting with soft contacted mould was analyzed. Some theoretical and experimental models were presented, from which following results were obtained. 1) The electromagnetic force is related with electric conductivity of billet as a power function to 0.4. 2) The heat transfer between billet and mould is related with the contacting pressure, and it is a linear function for tin billet approximately. 3) The distance between initial solidification point and meniscus in billet is related with the surface magnetic flux density as a fourth root function. 4) The temperature gradient in the initial solidifying shell is reduced, which can decrease the tendency of hot tearing on the surface of billet, and increase the equiaxed crystal zone in billet. 5) The stronger the magnetic flux density is, the more shallow and the thinner the oscillation mark on the surface of billet is. 6) The depth of oscillation mark on the billet cast by the soft contacted mould can be reduced to about 10% in comparison with that on the billets cast by traditional mould. 7) In non dimensional condition, the average depth of the oscillation marks on the billets cast by the soft contacted mould decreases with increasing magnetic flux density on there as a complementary error function. [
基金ItemSponsored by National Natural Science Foundation of China (50274203) , National High Technology Research andDevelopment Programof China (2001AA337040) and National Fundamental Research and Development Plan of China(G1998061510)
文摘The distribution of the magnetic flux density in a soft-contact electromagnetic continuous casting （EMCC） rectangular mold was investigated. The experimental results show that with an increase in electric power, the magnetic flux density increases. The position where the maximum magnetic flux density appears will shift up when the coil moves to the top of the mold. At the same time, the maximum magnetic flux density will increase and the effective acting range of electromagnetic pressure will widen. As a result, in practice, the coil should be placed near the top part of the mold. The meniscus should be controlled near the top part of the coil, as this not only remarkably improves the billet surface quality but also saves energy. With the same electric power input, the higher the frequency, the lower the magnetic flux density.
