During the sintering process of iron ore,a large amount of nitrogen oxides is generated,for which there is currently no efficient and economical treatment process.Therefore,it is necessary to implement process control...During the sintering process of iron ore,a large amount of nitrogen oxides is generated,for which there is currently no efficient and economical treatment process.Therefore,it is necessary to implement process control in sintering production to keep the mass concentration of NO_(x)in sintering flue gas at a low level.Through industrial trials at sintering sites,methods such as correlation analysis,path analysis,and multiple linear regression were applied to analyze the influence of various factors on NO emissions during the sintering process.The results indicate that negative correlations exist between nitrogen monoxide(NO)emissions and negative pressure,permeability index,O_(2) concentration,CO concentration,and flue gas temperature.Conversely,positive correlations exist between NO emissions and dust concentration,water vapor volume fraction,and sintering bed speed.Among these factors,O_(2) concentration and dust concentration are identified as the most significant influencing factors on NO emissions.By analyzing the masses and modes of influence of different factors,the mechanisms of action of each factor were obtained.Specifically,O_(2) concentration,dust concentration,permeability index,CO concentration,and flue gas temperature play a direct dominant role in NO emissions during the sintering process,while water vapor volume fraction,sintering trolley speed,and negative pressure have an indirect effect.A predictive model for NO mass concentration in flue gas was established with an accuracy rate of 91.6%,showing consistent overall trends with actual values.Finally,denitrification strategies for sintering industrial production were proposed,along with prospects for preliminary denitrification of sintering flue gas using fluidized bed conditions in the duct.展开更多
A pre-reduction sintering process with flue gas recirculation(PSP_(fsg)-FGR)was developed to mitigate alkalis harm to the blast furnace and reduce the flue gas emission in the whole ironmaking process.The results indi...A pre-reduction sintering process with flue gas recirculation(PSP_(fsg)-FGR)was developed to mitigate alkalis harm to the blast furnace and reduce the flue gas emission in the whole ironmaking process.The results indicated that the pre-reduction sintering process(PSP)can effectively remove 58.02%of K and 30.68%of Na from raw mixtures and improve yield and tumbler index to 74.40%and 68.69%,respectively.Moreover,PSP was conducive to reducing NO_(x) and SO_(2)emissions and simultaneously increasing CO content in flue gas.Circulating CO-containing flue gas to sintering bed effectively recycled CO and further improved K and Na removal ratio to 74.11%and 32.92%,respectively.Microstructural analysis revealed that the pre-reduced sinter mainly consisted of magnetite,wustite and a small quantity of metallic iron,and very few silicate glass phase was also formed.This process can simultaneously realize alkali metal elements removal as well as flue gas emission reduction from the integrated ironmaking process.展开更多
Steel rolling sludge,an oil-containing waste generated during steel production,was difficult to manage.Prolonged storage poses significant environmental and health hazards.Most steel enterprises in China use steel rol...Steel rolling sludge,an oil-containing waste generated during steel production,was difficult to manage.Prolonged storage poses significant environmental and health hazards.Most steel enterprises in China use steel rolling sludge directly as a raw material for sintering.However,its adhesive nature caused poor mixing with other materials,affecting the quality of the sinter.Herein,the incorporation of steel rolling sludge incineration slag into the sintering process was investigated for experimental purposes.The results indicated that adding 1%incinerated steel rolling sludge to the sintering raw material was feasible.At this proportion,both the yield and the tumbler index of the sinter have improved,primarily due to the oxidation reaction of Fe_(3)O_(4)present in the steel rolling sludge incineration slag during the sintering process,which significantly increases the sensible heat of the sinter and enhances the sintering mineralization reaction.Notably,the addition of steel rolling sludge incineration slag reduced dioxin concentrations in the sintering flue gas.Although CO,NO_(x),and SO_(2)emission concentrations slightly increased,the existing flue gas treatment system effectively controlled their emissions.展开更多
Sinter is the core raw material for blast furnaces.Flue pressure,which is an important state parameter,affects sinter quality.In this paper,flue pressure prediction and optimization were studied based on the shapley a...Sinter is the core raw material for blast furnaces.Flue pressure,which is an important state parameter,affects sinter quality.In this paper,flue pressure prediction and optimization were studied based on the shapley additive explanation(SHAP)to predict the flue pressure and take targeted adjustment measures.First,the sintering process data were collected and processed.A flue pressure prediction model was then constructed after comparing different feature selection methods and model algorithms using SHAP+extremely random-ized trees(ET).The prediction accuracy of the model within the error range of±0.25 kPa was 92.63%.SHAP analysis was employed to improve the interpretability of the prediction model.The effects of various sintering operation parameters on flue pressure,the relation-ship between the numerical range of key operation parameters and flue pressure,the effect of operation parameter combinations on flue pressure,and the prediction process of the flue pressure prediction model on a single sample were analyzed.A flue pressure optimization module was also constructed and analyzed when the prediction satisfied the judgment conditions.The operating parameter combination was then pushed.The flue pressure was increased by 5.87%during the verification process,achieving a good optimization effect.展开更多
As the bed depth increases,sintering yield increases,but the productivity decreases.To reveal the reasons for the decrease in productivity and explore targeted solutions,the bed resistance of mixtures,wet zone,and com...As the bed depth increases,sintering yield increases,but the productivity decreases.To reveal the reasons for the decrease in productivity and explore targeted solutions,the bed resistance of mixtures,wet zone,and combustion zone was analyzed in the laboratory.The results showed that the decreased porosity of mixture resulted in the increased bed resistance by 160.56%when the bed depth increased from 600 to 1000 mm.After improving porosity of 1%by adding loosening bars with optimized size and distribution,the bed resistance decreased,and the productivity increased by 5%.The increase in bed depth increased the thickness of the wet zone from 120 to 680 mm and the resistance from 1.56 to 8.83 kPa.By using a three-stage intensive mixer and pre-adding water for granulation,the moisture of mixture was reduced by 0.6%,and the sintering productivity increased by 4%.Besides,the high bed resistance is mainly caused by the increase in the thickness of the combustion zone from 31.9 to 132.7 mm,and the bed resistance increased from 0.70 to 5.62 kPa.The bed resistance of the combustion zone at 900 mm was increased by 90.51%compared to 700 mm.After optimization of the distribution of coke breeze,the thickness of combustion zone at the lower layer decreased from 132.7 to 106.84 mm and permeability improved significantly.展开更多
1.Introduction.Ni-Mn-X(X=Ga,In,Sn,or Sb)Heusler alloys have versatile properties[1-4],such as shape memory effect[1],superelastic-ity[5],magnetocaloric effect[3],elastocaloric effect[6],and even multicaloric effect[7]...1.Introduction.Ni-Mn-X(X=Ga,In,Sn,or Sb)Heusler alloys have versatile properties[1-4],such as shape memory effect[1],superelastic-ity[5],magnetocaloric effect[3],elastocaloric effect[6],and even multicaloric effect[7],that indicate their potential for use in actu-ators,sensors,micropumps,energy harvesters,and solid-state re-frigeration[8-10].Among the alloys,Ni-Mn-Sn-based alloys are environment-friendly and cost-effective[6,7,11],and hence,they have received widespread attention.展开更多
High-performance graphite materials have important roles in aerospace and nuclear reactor technologies because of their outstanding chemical stability and high-temperature performance.Their traditional production meth...High-performance graphite materials have important roles in aerospace and nuclear reactor technologies because of their outstanding chemical stability and high-temperature performance.Their traditional production method relies on repeated impregnation-carbonization and graphitization,and is plagued by lengthy preparation cycles and high energy consumption.Phase transition-assisted self-pressurized selfsintering technology can rapidly produce high-strength graphite materials,but the fracture strain of the graphite materials produced is poor.To solve this problem,this study used a two-step sintering method to uniformly introduce micro-nano pores into natural graphite-based bulk graphite,achieving improved fracture strain of the samples without reducing their density and mechanical properties.Using natural graphite powder,micron-diamond,and nano-diamond as raw materials,and by precisely controlling the staged pressure release process,the degree of diamond phase transition expansion was effectively regulated.The strain-to-failure of the graphite samples reached 1.2%,a 35%increase compared to samples produced by fullpressure sintering.Meanwhile,their flexural strength exceeded 110 MPa,and their density was over 1.9 g/cm^(3).The process therefore produced both a high strength and a high fracture strain.The interface evolution and toughening mechanism during the two-step sintering process were investigated.It is believed that the micro-nano pores formed have two roles:as stress concentrators they induce yielding by shear and as multi-crack propagation paths they significantly lengthen the crack propagation path.The two-step sintering phase transition strategy introduces pores and provides a new approach for increasing the fracture strain of brittle materials.展开更多
Ceramic dielectric materials with high dielectric strength and mechanisms of their internal factors affecting dielectric strength are significantly valuable for industrial application,especially for selection of suita...Ceramic dielectric materials with high dielectric strength and mechanisms of their internal factors affecting dielectric strength are significantly valuable for industrial application,especially for selection of suitable dielectric materials for high-power microwave transmission devices and reliable power transmission.Pure magnesium oxide(MgO),a kind of ceramic dielectric material,possesses great application potential in high-power microwave transmission devices due to its high theoretical dielectric strength,low dielectric constant,and low dielectric loss properties,but its application is limited by high sintering temperature during preparation.This work presented the preparation of a new type of multiphase ceramics based on MgO,which was MgO-1%ZrO_(2)-1%CaCO_(3-x)%MnCO_(3)(MZCM_(x),x=0,0.25,0.50,1.00,1.50,in molar),and their phase structures,morphological features,and dielectric properties were investigated.It was found that inclusion of ZrO_(2) and CaCO_(3) effectively inhibited excessive growth of MgO grains by formation of second phase,while addition of MnCO_(3) promoted the grain boundary diffusion process during the sintering process and reduced activation energy for the grain growth,resulting in a lower ceramic sintering temperature.Excellent performance,including high dielectric strength(Eb=92.3 kV/mm)and quality factor(Q×f=216642 GHz),simultaneously accompanying low dielectric loss(<0.03%),low temperature coefficient of dielectric constant(20.3×10^(–6)℃^(–1),85℃)and resonance frequency(–12.54×10^(–6)℃^(–1)),was achieved in MZCM1.00 ceramics under a relatively low sintering temperature of 1350℃.This work offers an effective solution for selecting dielectric materials for high-power microwave transmission devices.展开更多
ZnAl_(2)O_(4) and ZnAl_(2)O_(4)-based ceramics have attracted much attention from researchers due to their good microwave dielectric,thermal and mechanical properties.In this work,the influence of 5%(in mass)CuO-TiO_(...ZnAl_(2)O_(4) and ZnAl_(2)O_(4)-based ceramics have attracted much attention from researchers due to their good microwave dielectric,thermal and mechanical properties.In this work,the influence of 5%(in mass)CuO-TiO_(2)-Nb_(2)O_(5)(CTN)ternary composite oxide additives with different composition ratios on sintering behavior and properties of ZnAl_(2)O_(4) microwave dielectric ceramics was investigated.When the molar fraction ranges of Cu,Ti and Nb elements in 5%CTN additives are 0.625-0.875,0-0.250 and 0.125-0.625,respectively,sintering temperature of ZnAl_(2)O_(4) ceramics can be reduced from above 1400℃to below 1000℃.The sintering additives CN(Cu:Nb=1:1,molar ratio)and CTN(Cu:Ti:Nb=4:1:3,molar ratio)can reduce sintering temperature of ZnAl_(2)O_(4) ceramics to 975 and 1000℃,respectively,while maintaining good dielectric properties(dielectric constantε_(r)=11.36,quality factor Q׃=8245 GHz andε_(r)=9.52,Q׃=22249 GHz)and flexural strengths(200 and 161 MPa),which are expected to be applied in preparation of low temperature co-fired ceramic(LTCC)materials with copper electrodes.Low-temperature sintering of the ZnAl_(2)O_(4)+CTN system is characterized as activated sintering.Nanometer-level amorphous interfacial films containing Cu,Ti,and Nb elements are observed at the grain boundaries,which may provide fast diffusion pathways for mass transportation during the sintering process.Valence changes of Ti and Cu ions,along with changes of oxygen vacancies,are confirmed,which provides a potential mechanism for reduced sintering temperature of ZnAl_(2)O_(4) ceramics.In addition,a series of reactions occurring at the grain boundaries can activate these boundaries and further promote the sintering densification process.These results suggest a promising way to design a novel LTCC material with excellent properties based on the low temperature sintering of ceramics with the sintering aid of CuO-TiO_(2)-Nb_(2)O_(5) composite oxide.展开更多
Limestone was pretreated via the mechanical activation method,and burnt lime was partially substituted by the pretreated limestone for better sinter indices and lower sintering costs.With the reduction in the size dis...Limestone was pretreated via the mechanical activation method,and burnt lime was partially substituted by the pretreated limestone for better sinter indices and lower sintering costs.With the reduction in the size distribution of the pretreated limestone,the particle morphology,the activity of the calcined limestone and the fluidity of the liquid phase during sintering are all improved.When the substitution ratio of the pretreated limestone for burnt lime is kept at 50%,the granulation performance and sinter indices in sinter pot tests are both better compared with that of the base case.Much denser interleaved texture in product sinter is formed with the reduction of sinter porosity and improvement of silico-ferrite of calcium and alumina amount.When the particle size of the pretreated limestone is maintained within the optimal range of 0–2 mm,the tumble index,yield and productivity increase by 7.2%,2.6%and 11.2%,respectively,while the solid fuel rate decreases by 8.7%.In the corresponding sinter industry production,the tumble index and output of the product sinter are comparable to those of the base case,while the coke dosage is reduced by 9.0%.Reduction index and reduction degradation index(RDI_(+3.15))are both higher than 74%.The cost of raw materials in sintering process can be greatly reduced.展开更多
Nickel-based alloys applied in marine environments often face multiple challenges of stress,corrosion and wear.In this work,heterostructured NiCrTi alloy was prepared by spark plasma sintering coarse Ni20Cr and ultraf...Nickel-based alloys applied in marine environments often face multiple challenges of stress,corrosion and wear.In this work,heterostructured NiCrTi alloy was prepared by spark plasma sintering coarse Ni20Cr and ultrafine Ti powders.Apart that some are dissolved into the nickel alloy,Ti powders react in situ with Ni20Cr during sintering to form hard intermetallic Ni_(3)Ti.It builds up a typical heterostructure that endows NiCrTi alloy with well-balanced mechanical strength and plasticity,e.g.high yield strength of 1321 MPa,compressive strength of 2470 MPa,and compressive strain of 20%.On tribocorrosion,the hard shell enriched with Ti transforms to connected protrusion and form in situ surface texture.Oxides or wear debris are trapped at the textured surface and compacted to form a stable tribofilm.Thus negative synergy between corrosion and wear is observed for NiCrTi and high tribocorrosion resistance is achieved.At a potential of+0.3 V,the tribocorrosion rate of NiCrTi is reduced by an order of magnitude to 1.87×10^(-5)mm^(3)/(Nm)in comparison to the alloy Ni20Cr.展开更多
Four types of submicron Ag-coated Cu particles with different Ag contents were prepared as sintering paste fillers,and the Ag contents of the particles were measured to be 10,20,30,and 40 wt.%.Four types of particles(...Four types of submicron Ag-coated Cu particles with different Ag contents were prepared as sintering paste fillers,and the Ag contents of the particles were measured to be 10,20,30,and 40 wt.%.Four types of particles(in order of increasing Ag content:A10,A20,A30,and A40)were surface-modified with stearic acid,to suppress the Ag shell dewetting and improve sinterability.The surface-modified particles were mixed with a polyol-based solvent to fabricate a resin-free paste.Subsequently,the pastes were screen-printed onto a slide glass and sintered at 250°C in a nitrogen atmosphere for 1-10 min to form an electrode.The electrical resistivity of the sintered film as a function of sintering time was measured using a four-point probe.All the four surface-modified Cu@Ag particles with different Ag contents exhibited decreased electrical resistivity.Particularly,the largest difference in values after and before the surface modification was observed for A40 with the highest Ag content;the electrical resistivities of the initial and surface-modified particles were 1.51×10^(-4) and 6.67×10^(-5)Ω·cm,respectively,after sintering for 10 min.The findings of this study confirmed that the surface modification using stearic acid effectively suppressed the dewetting of the Ag shell and improved the sinterability of the submicron Cu@Ag particles.展开更多
Light-weight Mg-based alloys have gained attention owing to their various applications in engineering and biomedicalfields.Recent advancements in modern powder metallurgy techniques,such as spark plasma technique(SPS),...Light-weight Mg-based alloys have gained attention owing to their various applications in engineering and biomedicalfields.Recent advancements in modern powder metallurgy techniques,such as spark plasma technique(SPS),have enabled achieving near-net-shape products with tailored properties and decreased in-process oxidation.However,improving their mechanical and physical properties require further enhancement.In this study,a novel Mg-0.7Ca alloy was produced using SPS process.The effects of process parameters such as sintering time and additive type on the microstructural evolutions,phase arrangements,and mechanical and physical properties of the consolidated materials were investigated through various characterization techniques.Full-dense samples were produced from 60-minute ball-milled powder mixtures through spark plasma sintering at 420℃ for 7,10,and 13 min under 38 MPa of externally applied pressure.The obtained samples were then characterized using Field Emission Scanning Electron Microscopy(FESEM),Electron Backscatter Diffraction(EBSD),X-ray Energy Dispersive Spectroscopy(EDS),and X-ray Diffraction(XRD)analysis methods,as well as mechanical tests including compression strength and micro-hardness measurements.The results indicated that while improved densification behavior is observed in paraffin-contained samples,relatively better compression properties are achieved in starch-contained alloys.It is also found that the phase arrangement of the starch-contained samples includes higher fractions of the secondary phases such as oxides and residual carbons,which can positively affect the mechanical strength,despite decreased hardness.The microstructural characterizations showed an intensified thermomechanical response of the materials in both groups via increased sintering time.However,the competition between the influencing parameters causes scattered strengthening behavior and texture in the consolidated samples.Detailed discussions about the densification behavior,texture,and obtained characteristics were also included.展开更多
Additive manufacturing(AM)is an advanced production method for layer-by-layer fabrication,offering a paradigm shift in manufacturing.However,the sustainability of AM processes is poor,since suppliers recommend reusing...Additive manufacturing(AM)is an advanced production method for layer-by-layer fabrication,offering a paradigm shift in manufacturing.However,the sustainability of AM processes is poor,since suppliers recommend reusing 50%-70%of reprocessed powder,contributing to a significant increase in material disposal.To explore the possibility of fully reusing the polymeric material,we conduct a comprehensive characterisation of the powder particulates,in combination with analysis of the final prints.Utilizing optical and scanning electron microscopes,we statistically evaluate the size,morphology,and shape of the particles.Furthermore,tensile strength and deformation of printed bars is evaluated,showcasing the impact of aging on the print properties.The findings reveal that consecutive reuse of used powder significantly influences dimensional accuracy of the printed parts.We detect a 30.63%relative value of shrinkage after six printing iterations,which corresponds to an absolute shrinkage increase by 0.98%.This is significant considering the standard shrinkage for the material used is already 3.2%.Additionally,parts that are printed with reused material exhibit a small increase in elongation at yield,as well as an unexpected rise in tensile strength.Significant agglomeration of small particles is observed in the aged powder,since there are particles of less than 10μm,which are not found in the virgin powder.These results contribute to a better understanding of the issues related to the reusing of aged material,and offer invaluable insights for mitigating the environmental impact that is associated with material disposal in AM.展开更多
Iron phosphate based glass-ceramics with deliberately added Ce as an active nuclide simulant were prepared by microwave sintering.The sintering characteristics,including phases and structural evolution,and chemical du...Iron phosphate based glass-ceramics with deliberately added Ce as an active nuclide simulant were prepared by microwave sintering.The sintering characteristics,including phases and structural evolution,and chemical durability were investigated.XRD showed that NaZr_(2)(PO_(4))_(3) and FePO_(4) became the main crystalline phases of glass-ceramics with increasing sintering temperature.SEM revealed the glass-ceramics compactness increased first and then decreased as sintering temperature increased.Raman spectrum showed that,as sintering temperature increased,the network structure of glass-ceramics changed from mainly containing orthophosphate and pyrophosphate to a single orthophosphate.After immersion for 28 days,LR_(Na),LR_(Zr) and LR_(Ce) of the glass-ceramics prepared at 1000℃ were as low as 3.64×10^(-5),0.25×10^(-9) and 5.70×10^(-9)g/m^(2)/d respectively.The results indicate that iron phosphate based glass-ceramics can be prepared by rapid microwave sintering of glass powders and there is a potential of employing such microwave sintering technique in processing of glass-ceramics nuclear waste form.展开更多
As a reliable additive manufacturing technology,the stereolithography(SLA)ceramic core necessitates a tailored sintering process to achieve optimal performance.This study explored the effects of final sintering temper...As a reliable additive manufacturing technology,the stereolithography(SLA)ceramic core necessitates a tailored sintering process to achieve optimal performance.This study explored the effects of final sintering temperatures(specifically 1,150,1,250,and 1,300°C)on the properties of SLA-fabricated SiO_(2)-based ceramic cores reinforced with nano-ZrO_(2)(at concentrations of 1.0wt.%,1.5wt.%,and 2.0wt.%).The results demonstrate that increasing the final sintering temperature and the incorporation of nano-ZrO_(2)enhance the viscous fiow of quartz glass,resulting in a higher sintering degree.As the final sintering temperature rises,the ceramic samples exhibit increased shrinkage rate,decreased apparent porosity,and increased bulk density.Higher final sintering temperatures also promote greater cristobalite precipitation,promoting an increase in the amount and precipitation rate of quartz during investment casting.The formation of a cristobalite and ZrSiO_4 network at elevated temperatures effectively inhibits the viscous flow of quartz glass,thereby significantly improving high-temperature flexural strength and creep resistance of ceramic cores.When the content of nano-ZrO_(2)is between 1.5wt.%and 2.0wt.%,the final sintering temperature of 1,250°C is the best choice.Under these conditions,the shrinkage rate along the Z direction ranges from 3.35%to 3.68%,the porosity lies between 25.57%and 26.03%,the bulk density varies from 1.612 to 1.645 g·cm^(-3),the room temperature fiexural strength is between 26.79 and 27.85 MPa,and the fiexural strength at high temperatures is within the range of 30.77 to 33.02 MPa.The defiection at high-temperatures is 3.37-5.31 mm,while the surface roughness of the upper surface is 3.26-4.79μm,and the surface roughness of the side surface is 4.97-5.79μm.These findings provide valuable guidance for optimizing the sintering processes of SLA ceramic cores,offering potential for industrial applications.展开更多
1.Introduction B_(4)C ceramics have high potential for use in aerospace,military,nuclear energy,and other fields owing to their excellent properties such as low density,high melting point,high hardness,high chem-ical ...1.Introduction B_(4)C ceramics have high potential for use in aerospace,military,nuclear energy,and other fields owing to their excellent properties such as low density,high melting point,high hardness,high chem-ical stability,excellent wear resistance,and good neutron absorp-tion ability[1-3].However,the fracture toughness(1.9 MPa·m^(1/2))of B_(4)C is poor[2].Furthermore,the low diffusion coefficient asso-ciated with the strong covalent bond of B_(4)C makes it very difficult to achieve densification through traditional pressureless sintering.For example,after the pressureless sintering of B_(4)C at 2375℃ for 1 h,Roy et al.[4]achieved a relative density of only 87%.展开更多
The permeability of the sintering process can be significantly improved by the pellet sintering,but the excessive permeability will impact the heat accumulation of the sinter bed.Thus,it is very essential to clarify t...The permeability of the sintering process can be significantly improved by the pellet sintering,but the excessive permeability will impact the heat accumulation of the sinter bed.Thus,it is very essential to clarify the influence of the pellet particle size on the heat transfer process of sintering.Therefore,pilot-scale sinter pot tests of pellet sintering with manganese ore fines of different particle sizes were conducted,and traditional sintering was compared to reveal the heat transfer process of sintering and its impact on the microstructure of sintered ore.The results indicate that under suitable pellet sizes(8-12 mm),the heat transfer efficiency and the heat accumulation effect between the layers of sinter bed are strengthened by the pellet sintering,as well as the highest temperature in the combustion zone and the duration of high-temperature zone.This also leads to the further growth of ferrotephroite or hausmannite in liquid phase and its more reasonable crystal distribution.Ultimately,compared with the traditional sintering process,the total solid fuel consumption can be reduced by 20%-30%,and the productivity can be increased by 11.71%-16.21%.展开更多
BiCuSeO thermoelectric ceramics were fabricated using self-propagating high-temperature synthesis(SHS)combined with spark plasma sintering(SPS),and their phase compositions,microstructure,electrical properties,and the...BiCuSeO thermoelectric ceramics were fabricated using self-propagating high-temperature synthesis(SHS)combined with spark plasma sintering(SPS),and their phase compositions,microstructure,electrical properties,and thermal properties were systematically characterized and analyzed.The experimental results demonstrate that applying high-pressure condition during the sintering process will effectively restrict grain growth,reduce porosity,and lead to an increase in electrical conductivity.Simultaneously,high pressure sintering conditions reduce grain size and introduce additional grain boundaries and defects,which strengthens phonon scattering,thereby further decreasing both lattice thermal conductivity and total thermal conductivity.As a result,the high-pressure conditions significantly improve the thermoelectric figure of merit(ZT)of BiCuSeO.In brief,the samples sintered at 600℃under 200 MPa achieve a maximum ZT value of 0.64 at approximately 792 K.展开更多
To address the escalating demand for high-mobility transparent and conductive oxide(TCO)films in heterojunction solar cells,multiple components doped In_(2)O_(3) targets were proposed.The In_(2)O_(3) targets incorpora...To address the escalating demand for high-mobility transparent and conductive oxide(TCO)films in heterojunction solar cells,multiple components doped In_(2)O_(3) targets were proposed.The In_(2)O_(3) targets incorporating 1 wt.%CeO_(2),Ta_(2)O_(5),and TiO_(2) were sintered under different sintering temperatures and times.All the targets show the cubic bixbyite phase of In_(2)O_(3).The microstructure illustrates densely packed fine grains and uniform elemental distribution.Notably,increasing the sintering temperature and holding time contributes to effective pore elimination within the targets.A relative density of greater than 99.5%is obtained for the targets sintered at 1500℃ for 4 and 6 h,and the corresponding optimum resistivity decreases from 1.068×10^(-3)to 9.73×10^(-4)Ω·cm.These results provide the experimental basis of fabricating In_(2)O_(3)-based targets for depositing high mobility TCO films by magnetron sputtering.展开更多
基金supported by the National Natural Science Foundation of China(No.51974131)Hebei Outstanding Youth Fund Project(No.E2020209082),Tangshan Key R&D Program project(No.22150232J)Sixth Division Wujiaqu City Science and Technology Plan Project(2410).
文摘During the sintering process of iron ore,a large amount of nitrogen oxides is generated,for which there is currently no efficient and economical treatment process.Therefore,it is necessary to implement process control in sintering production to keep the mass concentration of NO_(x)in sintering flue gas at a low level.Through industrial trials at sintering sites,methods such as correlation analysis,path analysis,and multiple linear regression were applied to analyze the influence of various factors on NO emissions during the sintering process.The results indicate that negative correlations exist between nitrogen monoxide(NO)emissions and negative pressure,permeability index,O_(2) concentration,CO concentration,and flue gas temperature.Conversely,positive correlations exist between NO emissions and dust concentration,water vapor volume fraction,and sintering bed speed.Among these factors,O_(2) concentration and dust concentration are identified as the most significant influencing factors on NO emissions.By analyzing the masses and modes of influence of different factors,the mechanisms of action of each factor were obtained.Specifically,O_(2) concentration,dust concentration,permeability index,CO concentration,and flue gas temperature play a direct dominant role in NO emissions during the sintering process,while water vapor volume fraction,sintering trolley speed,and negative pressure have an indirect effect.A predictive model for NO mass concentration in flue gas was established with an accuracy rate of 91.6%,showing consistent overall trends with actual values.Finally,denitrification strategies for sintering industrial production were proposed,along with prospects for preliminary denitrification of sintering flue gas using fluidized bed conditions in the duct.
基金Project(52274290)supported by the National Natural Science Foundation of ChinaProject(72088101)supported by the Basic Science Center Project for National Natural Science Foundation of China。
文摘A pre-reduction sintering process with flue gas recirculation(PSP_(fsg)-FGR)was developed to mitigate alkalis harm to the blast furnace and reduce the flue gas emission in the whole ironmaking process.The results indicated that the pre-reduction sintering process(PSP)can effectively remove 58.02%of K and 30.68%of Na from raw mixtures and improve yield and tumbler index to 74.40%and 68.69%,respectively.Moreover,PSP was conducive to reducing NO_(x) and SO_(2)emissions and simultaneously increasing CO content in flue gas.Circulating CO-containing flue gas to sintering bed effectively recycled CO and further improved K and Na removal ratio to 74.11%and 32.92%,respectively.Microstructural analysis revealed that the pre-reduced sinter mainly consisted of magnetite,wustite and a small quantity of metallic iron,and very few silicate glass phase was also formed.This process can simultaneously realize alkali metal elements removal as well as flue gas emission reduction from the integrated ironmaking process.
基金supported by the National Natural Science Foundation of China(52204331)Natural Science Foundation of Anhui Province Youth Project(2208085QE145)the Open Project Program of Key Laboratory of Metallurgical Emission Reduction&Resources Recycling(Anhui University of Technology),Ministry of Education(JKF20-03).
文摘Steel rolling sludge,an oil-containing waste generated during steel production,was difficult to manage.Prolonged storage poses significant environmental and health hazards.Most steel enterprises in China use steel rolling sludge directly as a raw material for sintering.However,its adhesive nature caused poor mixing with other materials,affecting the quality of the sinter.Herein,the incorporation of steel rolling sludge incineration slag into the sintering process was investigated for experimental purposes.The results indicated that adding 1%incinerated steel rolling sludge to the sintering raw material was feasible.At this proportion,both the yield and the tumbler index of the sinter have improved,primarily due to the oxidation reaction of Fe_(3)O_(4)present in the steel rolling sludge incineration slag during the sintering process,which significantly increases the sensible heat of the sinter and enhances the sintering mineralization reaction.Notably,the addition of steel rolling sludge incineration slag reduced dioxin concentrations in the sintering flue gas.Although CO,NO_(x),and SO_(2)emission concentrations slightly increased,the existing flue gas treatment system effectively controlled their emissions.
基金supported by the General Program of the National Natural Science Foundation of China(No.52274326)the China Baowu Low Carbon Metallurgy Innovation Foundation(No.BWLCF202109)the Seventh Batch of Ten Thousand Talents Plan of China(No.ZX20220553).
文摘Sinter is the core raw material for blast furnaces.Flue pressure,which is an important state parameter,affects sinter quality.In this paper,flue pressure prediction and optimization were studied based on the shapley additive explanation(SHAP)to predict the flue pressure and take targeted adjustment measures.First,the sintering process data were collected and processed.A flue pressure prediction model was then constructed after comparing different feature selection methods and model algorithms using SHAP+extremely random-ized trees(ET).The prediction accuracy of the model within the error range of±0.25 kPa was 92.63%.SHAP analysis was employed to improve the interpretability of the prediction model.The effects of various sintering operation parameters on flue pressure,the relation-ship between the numerical range of key operation parameters and flue pressure,the effect of operation parameter combinations on flue pressure,and the prediction process of the flue pressure prediction model on a single sample were analyzed.A flue pressure optimization module was also constructed and analyzed when the prediction satisfied the judgment conditions.The operating parameter combination was then pushed.The flue pressure was increased by 5.87%during the verification process,achieving a good optimization effect.
基金supported by the Basic Science Center Project for the National Natural Science Foundation of China(No.72088101)the S&T Program of Hebei(No.23564101D).
文摘As the bed depth increases,sintering yield increases,but the productivity decreases.To reveal the reasons for the decrease in productivity and explore targeted solutions,the bed resistance of mixtures,wet zone,and combustion zone was analyzed in the laboratory.The results showed that the decreased porosity of mixture resulted in the increased bed resistance by 160.56%when the bed depth increased from 600 to 1000 mm.After improving porosity of 1%by adding loosening bars with optimized size and distribution,the bed resistance decreased,and the productivity increased by 5%.The increase in bed depth increased the thickness of the wet zone from 120 to 680 mm and the resistance from 1.56 to 8.83 kPa.By using a three-stage intensive mixer and pre-adding water for granulation,the moisture of mixture was reduced by 0.6%,and the sintering productivity increased by 4%.Besides,the high bed resistance is mainly caused by the increase in the thickness of the combustion zone from 31.9 to 132.7 mm,and the bed resistance increased from 0.70 to 5.62 kPa.The bed resistance of the combustion zone at 900 mm was increased by 90.51%compared to 700 mm.After optimization of the distribution of coke breeze,the thickness of combustion zone at the lower layer decreased from 132.7 to 106.84 mm and permeability improved significantly.
基金supported by the National Key R&D Pro-gram of China(No.2022YFB3805701)National Natural Science Foundation of China(NSFC)(No.52371182,51701052,52192592,52192593)+1 种基金Young Elite Scientists Sponsorship Program by CAST(No.2019QNRC001)the Heilongjiang Touyan Innovation Team Program.
文摘1.Introduction.Ni-Mn-X(X=Ga,In,Sn,or Sb)Heusler alloys have versatile properties[1-4],such as shape memory effect[1],superelastic-ity[5],magnetocaloric effect[3],elastocaloric effect[6],and even multicaloric effect[7],that indicate their potential for use in actu-ators,sensors,micropumps,energy harvesters,and solid-state re-frigeration[8-10].Among the alloys,Ni-Mn-Sn-based alloys are environment-friendly and cost-effective[6,7,11],and hence,they have received widespread attention.
基金Natural Science Foundation of Shanghai(24ZR1400800)he Natural Science Foundation of China(U23A20685,52073058,91963204)+1 种基金the National Key R&D Program of China(2021YFB3701400)Shanghai Sailing Program(23YF1400200)。
文摘High-performance graphite materials have important roles in aerospace and nuclear reactor technologies because of their outstanding chemical stability and high-temperature performance.Their traditional production method relies on repeated impregnation-carbonization and graphitization,and is plagued by lengthy preparation cycles and high energy consumption.Phase transition-assisted self-pressurized selfsintering technology can rapidly produce high-strength graphite materials,but the fracture strain of the graphite materials produced is poor.To solve this problem,this study used a two-step sintering method to uniformly introduce micro-nano pores into natural graphite-based bulk graphite,achieving improved fracture strain of the samples without reducing their density and mechanical properties.Using natural graphite powder,micron-diamond,and nano-diamond as raw materials,and by precisely controlling the staged pressure release process,the degree of diamond phase transition expansion was effectively regulated.The strain-to-failure of the graphite samples reached 1.2%,a 35%increase compared to samples produced by fullpressure sintering.Meanwhile,their flexural strength exceeded 110 MPa,and their density was over 1.9 g/cm^(3).The process therefore produced both a high strength and a high fracture strain.The interface evolution and toughening mechanism during the two-step sintering process were investigated.It is believed that the micro-nano pores formed have two roles:as stress concentrators they induce yielding by shear and as multi-crack propagation paths they significantly lengthen the crack propagation path.The two-step sintering phase transition strategy introduces pores and provides a new approach for increasing the fracture strain of brittle materials.
基金Student Training Program for Innovation and Entrepreneurship of Hangzhou Institute for Advanced Study,UCAS(CXCY20230305)Chinese Academy of Sciences Key Project(ZDRW-CN-2021-3-1-18)。
文摘Ceramic dielectric materials with high dielectric strength and mechanisms of their internal factors affecting dielectric strength are significantly valuable for industrial application,especially for selection of suitable dielectric materials for high-power microwave transmission devices and reliable power transmission.Pure magnesium oxide(MgO),a kind of ceramic dielectric material,possesses great application potential in high-power microwave transmission devices due to its high theoretical dielectric strength,low dielectric constant,and low dielectric loss properties,but its application is limited by high sintering temperature during preparation.This work presented the preparation of a new type of multiphase ceramics based on MgO,which was MgO-1%ZrO_(2)-1%CaCO_(3-x)%MnCO_(3)(MZCM_(x),x=0,0.25,0.50,1.00,1.50,in molar),and their phase structures,morphological features,and dielectric properties were investigated.It was found that inclusion of ZrO_(2) and CaCO_(3) effectively inhibited excessive growth of MgO grains by formation of second phase,while addition of MnCO_(3) promoted the grain boundary diffusion process during the sintering process and reduced activation energy for the grain growth,resulting in a lower ceramic sintering temperature.Excellent performance,including high dielectric strength(Eb=92.3 kV/mm)and quality factor(Q×f=216642 GHz),simultaneously accompanying low dielectric loss(<0.03%),low temperature coefficient of dielectric constant(20.3×10^(–6)℃^(–1),85℃)and resonance frequency(–12.54×10^(–6)℃^(–1)),was achieved in MZCM1.00 ceramics under a relatively low sintering temperature of 1350℃.This work offers an effective solution for selecting dielectric materials for high-power microwave transmission devices.
基金National Natural Science Foundation of China (U24A2052)Shanghai Eastern Talent Plan。
文摘ZnAl_(2)O_(4) and ZnAl_(2)O_(4)-based ceramics have attracted much attention from researchers due to their good microwave dielectric,thermal and mechanical properties.In this work,the influence of 5%(in mass)CuO-TiO_(2)-Nb_(2)O_(5)(CTN)ternary composite oxide additives with different composition ratios on sintering behavior and properties of ZnAl_(2)O_(4) microwave dielectric ceramics was investigated.When the molar fraction ranges of Cu,Ti and Nb elements in 5%CTN additives are 0.625-0.875,0-0.250 and 0.125-0.625,respectively,sintering temperature of ZnAl_(2)O_(4) ceramics can be reduced from above 1400℃to below 1000℃.The sintering additives CN(Cu:Nb=1:1,molar ratio)and CTN(Cu:Ti:Nb=4:1:3,molar ratio)can reduce sintering temperature of ZnAl_(2)O_(4) ceramics to 975 and 1000℃,respectively,while maintaining good dielectric properties(dielectric constantε_(r)=11.36,quality factor Q׃=8245 GHz andε_(r)=9.52,Q׃=22249 GHz)and flexural strengths(200 and 161 MPa),which are expected to be applied in preparation of low temperature co-fired ceramic(LTCC)materials with copper electrodes.Low-temperature sintering of the ZnAl_(2)O_(4)+CTN system is characterized as activated sintering.Nanometer-level amorphous interfacial films containing Cu,Ti,and Nb elements are observed at the grain boundaries,which may provide fast diffusion pathways for mass transportation during the sintering process.Valence changes of Ti and Cu ions,along with changes of oxygen vacancies,are confirmed,which provides a potential mechanism for reduced sintering temperature of ZnAl_(2)O_(4) ceramics.In addition,a series of reactions occurring at the grain boundaries can activate these boundaries and further promote the sintering densification process.These results suggest a promising way to design a novel LTCC material with excellent properties based on the low temperature sintering of ceramics with the sintering aid of CuO-TiO_(2)-Nb_(2)O_(5) composite oxide.
基金supported by Natural Science Foundation of Chongqing(No.CSTB2023NSCQ-BHX0166)Postdoctoral Science Foundation of China(No.2024T171095)Fundamental Research Funds for the Central Universities(No.2024CDJXY003).
文摘Limestone was pretreated via the mechanical activation method,and burnt lime was partially substituted by the pretreated limestone for better sinter indices and lower sintering costs.With the reduction in the size distribution of the pretreated limestone,the particle morphology,the activity of the calcined limestone and the fluidity of the liquid phase during sintering are all improved.When the substitution ratio of the pretreated limestone for burnt lime is kept at 50%,the granulation performance and sinter indices in sinter pot tests are both better compared with that of the base case.Much denser interleaved texture in product sinter is formed with the reduction of sinter porosity and improvement of silico-ferrite of calcium and alumina amount.When the particle size of the pretreated limestone is maintained within the optimal range of 0–2 mm,the tumble index,yield and productivity increase by 7.2%,2.6%and 11.2%,respectively,while the solid fuel rate decreases by 8.7%.In the corresponding sinter industry production,the tumble index and output of the product sinter are comparable to those of the base case,while the coke dosage is reduced by 9.0%.Reduction index and reduction degradation index(RDI_(+3.15))are both higher than 74%.The cost of raw materials in sintering process can be greatly reduced.
基金financially supported by the Liaoning Revitalization Talents Program(No.XLYC2203133)the Fundamental Research Funds for the Central Universities(No.N2302018)the Ningbo Yuyao City Science and Technology Plan Project(No.2023J03010010).
文摘Nickel-based alloys applied in marine environments often face multiple challenges of stress,corrosion and wear.In this work,heterostructured NiCrTi alloy was prepared by spark plasma sintering coarse Ni20Cr and ultrafine Ti powders.Apart that some are dissolved into the nickel alloy,Ti powders react in situ with Ni20Cr during sintering to form hard intermetallic Ni_(3)Ti.It builds up a typical heterostructure that endows NiCrTi alloy with well-balanced mechanical strength and plasticity,e.g.high yield strength of 1321 MPa,compressive strength of 2470 MPa,and compressive strain of 20%.On tribocorrosion,the hard shell enriched with Ti transforms to connected protrusion and form in situ surface texture.Oxides or wear debris are trapped at the textured surface and compacted to form a stable tribofilm.Thus negative synergy between corrosion and wear is observed for NiCrTi and high tribocorrosion resistance is achieved.At a potential of+0.3 V,the tribocorrosion rate of NiCrTi is reduced by an order of magnitude to 1.87×10^(-5)mm^(3)/(Nm)in comparison to the alloy Ni20Cr.
基金supported by the National Research Foundation of Korea(NRF)grant funded by the Korea government(MSIT)(No.2021R1A2C1007400)supported,partly,by the National R&D Program through the National Research Foundation of Korea(NRF)funded by the Ministry of Science and ICT(Nos.NRF-2020M3H4A3106383,NRF2020M3H4A3081764)+1 种基金supported,partly,by ETRI(No.21YB1610)supported by a Korea Institute for Advancement of Technology(KIAT)grant funded by the Korea Government(MOTIE)(No.P0008458,HRD Program for Industrial Innovation)。
文摘Four types of submicron Ag-coated Cu particles with different Ag contents were prepared as sintering paste fillers,and the Ag contents of the particles were measured to be 10,20,30,and 40 wt.%.Four types of particles(in order of increasing Ag content:A10,A20,A30,and A40)were surface-modified with stearic acid,to suppress the Ag shell dewetting and improve sinterability.The surface-modified particles were mixed with a polyol-based solvent to fabricate a resin-free paste.Subsequently,the pastes were screen-printed onto a slide glass and sintered at 250°C in a nitrogen atmosphere for 1-10 min to form an electrode.The electrical resistivity of the sintered film as a function of sintering time was measured using a four-point probe.All the four surface-modified Cu@Ag particles with different Ag contents exhibited decreased electrical resistivity.Particularly,the largest difference in values after and before the surface modification was observed for A40 with the highest Ag content;the electrical resistivities of the initial and surface-modified particles were 1.51×10^(-4) and 6.67×10^(-5)Ω·cm,respectively,after sintering for 10 min.The findings of this study confirmed that the surface modification using stearic acid effectively suppressed the dewetting of the Ag shell and improved the sinterability of the submicron Cu@Ag particles.
文摘Light-weight Mg-based alloys have gained attention owing to their various applications in engineering and biomedicalfields.Recent advancements in modern powder metallurgy techniques,such as spark plasma technique(SPS),have enabled achieving near-net-shape products with tailored properties and decreased in-process oxidation.However,improving their mechanical and physical properties require further enhancement.In this study,a novel Mg-0.7Ca alloy was produced using SPS process.The effects of process parameters such as sintering time and additive type on the microstructural evolutions,phase arrangements,and mechanical and physical properties of the consolidated materials were investigated through various characterization techniques.Full-dense samples were produced from 60-minute ball-milled powder mixtures through spark plasma sintering at 420℃ for 7,10,and 13 min under 38 MPa of externally applied pressure.The obtained samples were then characterized using Field Emission Scanning Electron Microscopy(FESEM),Electron Backscatter Diffraction(EBSD),X-ray Energy Dispersive Spectroscopy(EDS),and X-ray Diffraction(XRD)analysis methods,as well as mechanical tests including compression strength and micro-hardness measurements.The results indicated that while improved densification behavior is observed in paraffin-contained samples,relatively better compression properties are achieved in starch-contained alloys.It is also found that the phase arrangement of the starch-contained samples includes higher fractions of the secondary phases such as oxides and residual carbons,which can positively affect the mechanical strength,despite decreased hardness.The microstructural characterizations showed an intensified thermomechanical response of the materials in both groups via increased sintering time.However,the competition between the influencing parameters causes scattered strengthening behavior and texture in the consolidated samples.Detailed discussions about the densification behavior,texture,and obtained characteristics were also included.
文摘Additive manufacturing(AM)is an advanced production method for layer-by-layer fabrication,offering a paradigm shift in manufacturing.However,the sustainability of AM processes is poor,since suppliers recommend reusing 50%-70%of reprocessed powder,contributing to a significant increase in material disposal.To explore the possibility of fully reusing the polymeric material,we conduct a comprehensive characterisation of the powder particulates,in combination with analysis of the final prints.Utilizing optical and scanning electron microscopes,we statistically evaluate the size,morphology,and shape of the particles.Furthermore,tensile strength and deformation of printed bars is evaluated,showcasing the impact of aging on the print properties.The findings reveal that consecutive reuse of used powder significantly influences dimensional accuracy of the printed parts.We detect a 30.63%relative value of shrinkage after six printing iterations,which corresponds to an absolute shrinkage increase by 0.98%.This is significant considering the standard shrinkage for the material used is already 3.2%.Additionally,parts that are printed with reused material exhibit a small increase in elongation at yield,as well as an unexpected rise in tensile strength.Significant agglomeration of small particles is observed in the aged powder,since there are particles of less than 10μm,which are not found in the virgin powder.These results contribute to a better understanding of the issues related to the reusing of aged material,and offer invaluable insights for mitigating the environmental impact that is associated with material disposal in AM.
基金Funded by the Key Research and Development Projects of Anhui Province(No.2022a05020026)the Key Technologies R&D Program of CNBM(Nos.2021HX0809,2021HX1011)the Anhui Science and Technology Major Project(No.2021e03020009)。
文摘Iron phosphate based glass-ceramics with deliberately added Ce as an active nuclide simulant were prepared by microwave sintering.The sintering characteristics,including phases and structural evolution,and chemical durability were investigated.XRD showed that NaZr_(2)(PO_(4))_(3) and FePO_(4) became the main crystalline phases of glass-ceramics with increasing sintering temperature.SEM revealed the glass-ceramics compactness increased first and then decreased as sintering temperature increased.Raman spectrum showed that,as sintering temperature increased,the network structure of glass-ceramics changed from mainly containing orthophosphate and pyrophosphate to a single orthophosphate.After immersion for 28 days,LR_(Na),LR_(Zr) and LR_(Ce) of the glass-ceramics prepared at 1000℃ were as low as 3.64×10^(-5),0.25×10^(-9) and 5.70×10^(-9)g/m^(2)/d respectively.The results indicate that iron phosphate based glass-ceramics can be prepared by rapid microwave sintering of glass powders and there is a potential of employing such microwave sintering technique in processing of glass-ceramics nuclear waste form.
基金supported by the Natural Science Foundation of Shanghai(No.23ZR1421500)the National Natural Science Foundation of China(Nos.52474412,52127807,52271035)+3 种基金the Shanghai Municipal Commission of Economy and Informatization(No.GYOJ2022-2-02)the United Innovation Program of Shanghai Commercial Aircraft Engine(No.AR966)the SPMI Project from Shanghai Academy of Spaceflight Technology(No.SPMI2022-06)the Ningbo International Science and Technology Cooperation Program(No.2023H004)。
文摘As a reliable additive manufacturing technology,the stereolithography(SLA)ceramic core necessitates a tailored sintering process to achieve optimal performance.This study explored the effects of final sintering temperatures(specifically 1,150,1,250,and 1,300°C)on the properties of SLA-fabricated SiO_(2)-based ceramic cores reinforced with nano-ZrO_(2)(at concentrations of 1.0wt.%,1.5wt.%,and 2.0wt.%).The results demonstrate that increasing the final sintering temperature and the incorporation of nano-ZrO_(2)enhance the viscous fiow of quartz glass,resulting in a higher sintering degree.As the final sintering temperature rises,the ceramic samples exhibit increased shrinkage rate,decreased apparent porosity,and increased bulk density.Higher final sintering temperatures also promote greater cristobalite precipitation,promoting an increase in the amount and precipitation rate of quartz during investment casting.The formation of a cristobalite and ZrSiO_4 network at elevated temperatures effectively inhibits the viscous flow of quartz glass,thereby significantly improving high-temperature flexural strength and creep resistance of ceramic cores.When the content of nano-ZrO_(2)is between 1.5wt.%and 2.0wt.%,the final sintering temperature of 1,250°C is the best choice.Under these conditions,the shrinkage rate along the Z direction ranges from 3.35%to 3.68%,the porosity lies between 25.57%and 26.03%,the bulk density varies from 1.612 to 1.645 g·cm^(-3),the room temperature fiexural strength is between 26.79 and 27.85 MPa,and the fiexural strength at high temperatures is within the range of 30.77 to 33.02 MPa.The defiection at high-temperatures is 3.37-5.31 mm,while the surface roughness of the upper surface is 3.26-4.79μm,and the surface roughness of the side surface is 4.97-5.79μm.These findings provide valuable guidance for optimizing the sintering processes of SLA ceramic cores,offering potential for industrial applications.
基金supported by the National Natural Science Foun-dation of China(No.52372061)the Project of the Education Department of Jilin Province(No.JJKH20231163KJ).
文摘1.Introduction B_(4)C ceramics have high potential for use in aerospace,military,nuclear energy,and other fields owing to their excellent properties such as low density,high melting point,high hardness,high chem-ical stability,excellent wear resistance,and good neutron absorp-tion ability[1-3].However,the fracture toughness(1.9 MPa·m^(1/2))of B_(4)C is poor[2].Furthermore,the low diffusion coefficient asso-ciated with the strong covalent bond of B_(4)C makes it very difficult to achieve densification through traditional pressureless sintering.For example,after the pressureless sintering of B_(4)C at 2375℃ for 1 h,Roy et al.[4]achieved a relative density of only 87%.
基金supports from the National Science Foundation of China under Grant number of No.52174329China Baowu Low Carbon Metallurgy Innovation Foundation(BWLCF202216).
文摘The permeability of the sintering process can be significantly improved by the pellet sintering,but the excessive permeability will impact the heat accumulation of the sinter bed.Thus,it is very essential to clarify the influence of the pellet particle size on the heat transfer process of sintering.Therefore,pilot-scale sinter pot tests of pellet sintering with manganese ore fines of different particle sizes were conducted,and traditional sintering was compared to reveal the heat transfer process of sintering and its impact on the microstructure of sintered ore.The results indicate that under suitable pellet sizes(8-12 mm),the heat transfer efficiency and the heat accumulation effect between the layers of sinter bed are strengthened by the pellet sintering,as well as the highest temperature in the combustion zone and the duration of high-temperature zone.This also leads to the further growth of ferrotephroite or hausmannite in liquid phase and its more reasonable crystal distribution.Ultimately,compared with the traditional sintering process,the total solid fuel consumption can be reduced by 20%-30%,and the productivity can be increased by 11.71%-16.21%.
基金Funded by the National Natural Science Foundation of China(Nos.52322207 and 52202289)the National Key Research and Development Plan of China(No.2021YFB3701400)+2 种基金the Independent Innovation Projects of the Hubei Longzhong Laboratory(No.2022ZZ-11)Funded by the National Natural Science Foundation of China(Nos.52322207 and 52202289)the National Key Research and Development Plan of China(No.2021YFB3701400)the Independent Innovation Projects of the Hubei Longzhong Laboratory(No.2022ZZ-11)。
文摘BiCuSeO thermoelectric ceramics were fabricated using self-propagating high-temperature synthesis(SHS)combined with spark plasma sintering(SPS),and their phase compositions,microstructure,electrical properties,and thermal properties were systematically characterized and analyzed.The experimental results demonstrate that applying high-pressure condition during the sintering process will effectively restrict grain growth,reduce porosity,and lead to an increase in electrical conductivity.Simultaneously,high pressure sintering conditions reduce grain size and introduce additional grain boundaries and defects,which strengthens phonon scattering,thereby further decreasing both lattice thermal conductivity and total thermal conductivity.As a result,the high-pressure conditions significantly improve the thermoelectric figure of merit(ZT)of BiCuSeO.In brief,the samples sintered at 600℃under 200 MPa achieve a maximum ZT value of 0.64 at approximately 792 K.
基金supported by the Joint Fund of NSFC-Guangxi(U21A2065)Guangxi Natural Science Foundation(2021GXNSFAA220020)+1 种基金the National Natural Science Foundation of China(62364007)Science and Technology Major Project of Guangxi(AA21077018).
文摘To address the escalating demand for high-mobility transparent and conductive oxide(TCO)films in heterojunction solar cells,multiple components doped In_(2)O_(3) targets were proposed.The In_(2)O_(3) targets incorporating 1 wt.%CeO_(2),Ta_(2)O_(5),and TiO_(2) were sintered under different sintering temperatures and times.All the targets show the cubic bixbyite phase of In_(2)O_(3).The microstructure illustrates densely packed fine grains and uniform elemental distribution.Notably,increasing the sintering temperature and holding time contributes to effective pore elimination within the targets.A relative density of greater than 99.5%is obtained for the targets sintered at 1500℃ for 4 and 6 h,and the corresponding optimum resistivity decreases from 1.068×10^(-3)to 9.73×10^(-4)Ω·cm.These results provide the experimental basis of fabricating In_(2)O_(3)-based targets for depositing high mobility TCO films by magnetron sputtering.
