A metal rubber（MR） dry friction damper was designed based on the load supported by the rotor. An experimental apparatus for obtaining hysteresis loops of support under the precession load was designed. The elastic-d...A metal rubber（MR） dry friction damper was designed based on the load supported by the rotor. An experimental apparatus for obtaining hysteresis loops of support under the precession load was designed. The elastic-damping characteristics of the ring-shaped MR damper used as a rotor support under variable loads were presented by studying the hysteresis loops of the damper. The vibration rigidity and the energy dissipation coefficient were calculated from the hysteresis loops, based on the description of the deformation process of the MR element with simple structure in a dimensionless coordinating system. The calculation results showed that the energy dissipation coefficient in the inner of MR element and on the boundary between the damper and the frame of the rotor support were approximately equal. The comparison of the hysteresis loops for a precession load and a one-axial load indicated a large difference when the coefficient of the energy dissipation and the stiffness of the MR damper were concerned.展开更多
The elastic support/dry friction damper is a type of damper which is used for active vibration control in a rotor system.To establish the analytical model of this type of damper,a two-dimensional friction model-ball/p...The elastic support/dry friction damper is a type of damper which is used for active vibration control in a rotor system.To establish the analytical model of this type of damper,a two-dimensional friction model-ball/plate model was proposed.By using this ball/plate model,a dynamics model of rotor with elastic support/dry friction dampers was established and experimentally verified.Moreover,the damping performance of the elastic support/dry friction damper was studied numerically with respect to some variable parameters.The numerical study shows that the damping performance of the elastic support/dry friction damper is closely related to the stiffness distribution of the rotor-support system,the damper location,the pressing force between the moving and stationary disk,the friction coefficient,the tangential contact stiffness of the contact interface,and the stiffness of the stationary disk.In general,the damper should be located on an elastic support which has a large vibration amplitude in order to achieve a better damping performance,and the more vibration energy in this elastic support concentrates,the better performance of the damper will be.The larger the tangential contact stiffness of the contact interface,and the stiffness of the stationary disk are,the better performance of the damper will be.There will be an optimal value of the friction force at which the damper performs best.展开更多
An aero-engine rotor system is simplified as an unsymmetrical-rigid-rotor with nonlinear-elastic-support based on its characteristics. Governing equations of the rubbing system, obtained from the Lagrange equation, ar...An aero-engine rotor system is simplified as an unsymmetrical-rigid-rotor with nonlinear-elastic-support based on its characteristics. Governing equations of the rubbing system, obtained from the Lagrange equation, are solved by the averaging method to find the bifurcation equations. Then, according to the two-dimensional constraint bi- furcation theory, transition sets and bifurcation diagrams of the system with and without rubbing are given to study the influence of system eccentricity and damping on the bi- furcation behaviors, respectively. Finally, according to the Lyapunov stability theory, the stability region of the steady-state rubbing solution, the boundary of static bifurcation, and the Hopf bifurcation are determined to discuss the influence of system parameters on the evolution of system motion. The results may provide some references for the designer in aero rotor systems.展开更多
A novel transient rotor current control scheme is proposed in this paper for a doubly-fed induction generator（DFIG）equipped with a superconducting magnetic energy storage（SMES） device to enhance its transient volt...A novel transient rotor current control scheme is proposed in this paper for a doubly-fed induction generator（DFIG）equipped with a superconducting magnetic energy storage（SMES） device to enhance its transient voltage and frequency support capacity during grid faults. The SMES connected to the DC-link capacitor of the DFIG is controlled to regulate the transient dc-link voltage so that the whole capacity of the grid side converter（GSC） is dedicated to injecting reactive power to the grid for the transient voltage support. However, the rotor-side converter（RSC） has different control tasks for different periods of the grid fault. Firstly, for Period I, the RSC injects the demagnetizing current to ensure the controllability of the rotor voltage. Then, since the dc stator flux degenerates rapidly in Period II, the required demagnetizing current is low in Period II and the RSC uses the spare capacity to additionally generate the reactive（priority） and active current so that the transient voltage capability is corroborated and the DFIG also positively responds to the system frequency dynamic at the earliest time. Finally, a small amount of demagnetizing current is provided after the fault clearance. Most of the RSC capacity is used to inject the active current to further support the frequency recovery of the system. Simulations are carried out on a simple power system with a wind farm. Comparisons with other commonly used control methods are performed to validate the proposed control method.展开更多
In order to clarify the effects of support structure on a dual-rotor machine,a dynamic model is established which takes into consideration the contact force of ball bearing and the cubic stiffness of elastic support. ...In order to clarify the effects of support structure on a dual-rotor machine,a dynamic model is established which takes into consideration the contact force of ball bearing and the cubic stiffness of elastic support. Bearing clearance,Hertz contact between the ball and race and the varying compliance effect are included in the model of ball bearing. The system response is obtained through numerical integration method,and the vibration due to the periodic change of bearing stiffness is investigated. The motions of periodic,quasiperiodic and even chaotic are found when bearing clearance is used as control parameter to simulate the response of rotor system. The results reveal two typical routes to chaos: quasi-periodic bifurcation and intermittent bifurcation. Large cubic stiffness of elastic support may cause jump and hysteresis phenomena in resonance curve when rotors run at the critical-speed region. The modeling results acquired by numerical simulation will contribute to understanding and controlling of the nonlinear behaviors of the dual-rotor system.展开更多
Considering the elastic supports,the finite element model of rotor-bladed disk-casing system is established using commercial software ANSYS/LS-DYNA.Assuming that broken blade is released from the disk,the complicate r...Considering the elastic supports,the finite element model of rotor-bladed disk-casing system is established using commercial software ANSYS/LS-DYNA.Assuming that broken blade is released from the disk,the complicate rubbing responses of unbalanced rotor-bladed disk-casing system are studied under different operational speeds.In addition,influences of both plastic deformation of blade and casing failure are analyzed.The results show that there exist some multiple even fractional frequencies in the transient and steady vibration responses of unbalanced rotor.Besides,one nodal diameter vibration of bladed disk coupling with the lateral vibration of the shaft as well as the first order bending vibration of blade can be excited under low operational speed,while the first order bending vibration of blade coupling with the lateral vibration of disk-shaft is easily excited under high operational speed.During rubbing process,three distinct contact states can be observed:broken blade-casing contact,broken blade-blade component-casing contact and broken blade-casing contact/blade component-casing contact/blade selfcontact.It is worth noting that the third contact state is related to the operational speed.With the increase of operational speed,self-contact in the blade may occur.展开更多
振动抑制是保障武器装备安全运行的重要基础,在航空发动机中广泛使用弹性环挤压油膜阻尼器(Elastic Ring Squeeze Film Dampers,ERSFD)抑制转子系统振动响应。针对多支点支承的悬臂动力涡轮转子,通过有限元分析和敏感度评估,阐明了ERSF...振动抑制是保障武器装备安全运行的重要基础,在航空发动机中广泛使用弹性环挤压油膜阻尼器(Elastic Ring Squeeze Film Dampers,ERSFD)抑制转子系统振动响应。针对多支点支承的悬臂动力涡轮转子,通过有限元分析和敏感度评估,阐明了ERSFD在不同转子特性下的减振效果。研究结果表明,合理的结构及刚度设计能够有效提升ERSFD的动力特性,为高速转子系统提供更优的抑振效果。不同弹性环支承阻尼对悬臂转子响应的幅值抑制敏感性有所不同,受转子振型等特征影响,对于双支点支承的悬臂动力涡轮,远离动力涡轮支点(5#支点)应用阻尼结构,有利于降低轴段弯曲振型下振动响应;而靠近悬臂动力涡轮支点(6#支点)的阻尼结构,对动力涡轮摆动振动响应抑制效果更显著,可实现振动响应衰减超过70%。通过有针对性地开展弹性环支承阻尼设计,可实现对多支点悬臂动力涡轮转子多阶振型下振动响应抑制。展开更多
机动飞行条件下高速转子系统会同时受到环境载荷以及转子自身的共同激励而产生强烈的强迫响应。为研究其复杂的振动特性,本文采用Vold-Kalman滤波(Vold-Kalman Filter,VKF)对不同基础运动激励下转子系统的实测振动信号进行阶次跟踪滤波...机动飞行条件下高速转子系统会同时受到环境载荷以及转子自身的共同激励而产生强烈的强迫响应。为研究其复杂的振动特性,本文采用Vold-Kalman滤波(Vold-Kalman Filter,VKF)对不同基础运动激励下转子系统的实测振动信号进行阶次跟踪滤波。为验证VKF的有效性及参数设置的可靠性,通过转子动力特性计算生成系统响应的仿真信号,并通过加噪处理模拟测量信号,然后通过VKF提取目标阶次的时域波形。通过陀螺运动转子动力学试验,测得不同基础转动激起的系统振动响应,组合使用VKF和计算阶次跟踪(Computed Order Tracking,COT)提取并分离了转子转频信号和基础低频信号的时域和阶次信息。结果表明,单轴滚转或俯仰运动均会激起与其频率一致的低频振动响应,且滚转、俯仰角速度的大小会影响该低频信号的幅值大小;随着基础运动角速度的变化,转子前四阶振动分量没有发生明显的变化,而基础运动频率与转频之间的频带区域有显著变化。此方法有效地提升了机动飞行下转子支承系统振动信号处理与分析的准确度和效率,降低了信号噪声。展开更多
基金This project is supported by National Natural Science Foundation of China (No.50675042).
文摘A metal rubber（MR） dry friction damper was designed based on the load supported by the rotor. An experimental apparatus for obtaining hysteresis loops of support under the precession load was designed. The elastic-damping characteristics of the ring-shaped MR damper used as a rotor support under variable loads were presented by studying the hysteresis loops of the damper. The vibration rigidity and the energy dissipation coefficient were calculated from the hysteresis loops, based on the description of the deformation process of the MR element with simple structure in a dimensionless coordinating system. The calculation results showed that the energy dissipation coefficient in the inner of MR element and on the boundary between the damper and the frame of the rotor support were approximately equal. The comparison of the hysteresis loops for a precession load and a one-axial load indicated a large difference when the coefficient of the energy dissipation and the stiffness of the MR damper were concerned.
基金supported by the National Natural Science Foundation of China(No.51405393)
文摘The elastic support/dry friction damper is a type of damper which is used for active vibration control in a rotor system.To establish the analytical model of this type of damper,a two-dimensional friction model-ball/plate model was proposed.By using this ball/plate model,a dynamics model of rotor with elastic support/dry friction dampers was established and experimentally verified.Moreover,the damping performance of the elastic support/dry friction damper was studied numerically with respect to some variable parameters.The numerical study shows that the damping performance of the elastic support/dry friction damper is closely related to the stiffness distribution of the rotor-support system,the damper location,the pressing force between the moving and stationary disk,the friction coefficient,the tangential contact stiffness of the contact interface,and the stiffness of the stationary disk.In general,the damper should be located on an elastic support which has a large vibration amplitude in order to achieve a better damping performance,and the more vibration energy in this elastic support concentrates,the better performance of the damper will be.The larger the tangential contact stiffness of the contact interface,and the stiffness of the stationary disk are,the better performance of the damper will be.There will be an optimal value of the friction force at which the damper performs best.
文摘An aero-engine rotor system is simplified as an unsymmetrical-rigid-rotor with nonlinear-elastic-support based on its characteristics. Governing equations of the rubbing system, obtained from the Lagrange equation, are solved by the averaging method to find the bifurcation equations. Then, according to the two-dimensional constraint bi- furcation theory, transition sets and bifurcation diagrams of the system with and without rubbing are given to study the influence of system eccentricity and damping on the bi- furcation behaviors, respectively. Finally, according to the Lyapunov stability theory, the stability region of the steady-state rubbing solution, the boundary of static bifurcation, and the Hopf bifurcation are determined to discuss the influence of system parameters on the evolution of system motion. The results may provide some references for the designer in aero rotor systems.
基金supported by the National Natural Science Foundation of China(Grant No.51307124)the Major Program of the National Natural Science Foundation of China(Grant No.51190105)
文摘A novel transient rotor current control scheme is proposed in this paper for a doubly-fed induction generator（DFIG）equipped with a superconducting magnetic energy storage（SMES） device to enhance its transient voltage and frequency support capacity during grid faults. The SMES connected to the DC-link capacitor of the DFIG is controlled to regulate the transient dc-link voltage so that the whole capacity of the grid side converter（GSC） is dedicated to injecting reactive power to the grid for the transient voltage support. However, the rotor-side converter（RSC） has different control tasks for different periods of the grid fault. Firstly, for Period I, the RSC injects the demagnetizing current to ensure the controllability of the rotor voltage. Then, since the dc stator flux degenerates rapidly in Period II, the required demagnetizing current is low in Period II and the RSC uses the spare capacity to additionally generate the reactive（priority） and active current so that the transient voltage capability is corroborated and the DFIG also positively responds to the system frequency dynamic at the earliest time. Finally, a small amount of demagnetizing current is provided after the fault clearance. Most of the RSC capacity is used to inject the active current to further support the frequency recovery of the system. Simulations are carried out on a simple power system with a wind farm. Comparisons with other commonly used control methods are performed to validate the proposed control method.
基金Sponsored by the National Natural Science Foundation of China(Grant No.11302058)
文摘In order to clarify the effects of support structure on a dual-rotor machine,a dynamic model is established which takes into consideration the contact force of ball bearing and the cubic stiffness of elastic support. Bearing clearance,Hertz contact between the ball and race and the varying compliance effect are included in the model of ball bearing. The system response is obtained through numerical integration method,and the vibration due to the periodic change of bearing stiffness is investigated. The motions of periodic,quasiperiodic and even chaotic are found when bearing clearance is used as control parameter to simulate the response of rotor system. The results reveal two typical routes to chaos: quasi-periodic bifurcation and intermittent bifurcation. Large cubic stiffness of elastic support may cause jump and hysteresis phenomena in resonance curve when rotors run at the critical-speed region. The modeling results acquired by numerical simulation will contribute to understanding and controlling of the nonlinear behaviors of the dual-rotor system.
基金supported by the National Natural Science Foundation of China(No.11772089)the Fundamental Research Funds for the Central Universities (Nos. N160312001and N160313004)the Research Project of State Key Laboratory of Mechanical System and Vibration(No.MSV201707)
文摘Considering the elastic supports,the finite element model of rotor-bladed disk-casing system is established using commercial software ANSYS/LS-DYNA.Assuming that broken blade is released from the disk,the complicate rubbing responses of unbalanced rotor-bladed disk-casing system are studied under different operational speeds.In addition,influences of both plastic deformation of blade and casing failure are analyzed.The results show that there exist some multiple even fractional frequencies in the transient and steady vibration responses of unbalanced rotor.Besides,one nodal diameter vibration of bladed disk coupling with the lateral vibration of the shaft as well as the first order bending vibration of blade can be excited under low operational speed,while the first order bending vibration of blade coupling with the lateral vibration of disk-shaft is easily excited under high operational speed.During rubbing process,three distinct contact states can be observed:broken blade-casing contact,broken blade-blade component-casing contact and broken blade-casing contact/blade component-casing contact/blade selfcontact.It is worth noting that the third contact state is related to the operational speed.With the increase of operational speed,self-contact in the blade may occur.
文摘振动抑制是保障武器装备安全运行的重要基础,在航空发动机中广泛使用弹性环挤压油膜阻尼器(Elastic Ring Squeeze Film Dampers,ERSFD)抑制转子系统振动响应。针对多支点支承的悬臂动力涡轮转子,通过有限元分析和敏感度评估,阐明了ERSFD在不同转子特性下的减振效果。研究结果表明,合理的结构及刚度设计能够有效提升ERSFD的动力特性,为高速转子系统提供更优的抑振效果。不同弹性环支承阻尼对悬臂转子响应的幅值抑制敏感性有所不同,受转子振型等特征影响,对于双支点支承的悬臂动力涡轮,远离动力涡轮支点(5#支点)应用阻尼结构,有利于降低轴段弯曲振型下振动响应;而靠近悬臂动力涡轮支点(6#支点)的阻尼结构,对动力涡轮摆动振动响应抑制效果更显著,可实现振动响应衰减超过70%。通过有针对性地开展弹性环支承阻尼设计,可实现对多支点悬臂动力涡轮转子多阶振型下振动响应抑制。
文摘机动飞行条件下高速转子系统会同时受到环境载荷以及转子自身的共同激励而产生强烈的强迫响应。为研究其复杂的振动特性,本文采用Vold-Kalman滤波(Vold-Kalman Filter,VKF)对不同基础运动激励下转子系统的实测振动信号进行阶次跟踪滤波。为验证VKF的有效性及参数设置的可靠性,通过转子动力特性计算生成系统响应的仿真信号,并通过加噪处理模拟测量信号,然后通过VKF提取目标阶次的时域波形。通过陀螺运动转子动力学试验,测得不同基础转动激起的系统振动响应,组合使用VKF和计算阶次跟踪(Computed Order Tracking,COT)提取并分离了转子转频信号和基础低频信号的时域和阶次信息。结果表明,单轴滚转或俯仰运动均会激起与其频率一致的低频振动响应,且滚转、俯仰角速度的大小会影响该低频信号的幅值大小;随着基础运动角速度的变化,转子前四阶振动分量没有发生明显的变化,而基础运动频率与转频之间的频带区域有显著变化。此方法有效地提升了机动飞行下转子支承系统振动信号处理与分析的准确度和效率,降低了信号噪声。
