Multi-layer riveted structures are widely applied to aircraft.During the service,cracks may appear within these structures due to stress concentration of the riveted holes.The guided wave monitoring has been proved to...Multi-layer riveted structures are widely applied to aircraft.During the service,cracks may appear within these structures due to stress concentration of the riveted holes.The guided wave monitoring has been proved to be an effective tool to deal with this problem.However,there is a lack of understanding of the wave propagation process across such kinds of structures.This study proposes a piezoelectric guided wave simulation method to reveal the propagation of guided waves in multi-layer riveted structures.Effects of pretension force,friction coefficient,and cracks that might influence wave characteristics are studied.The guided wave simulation data is compared with the experimental results and the results verify the simulation model.Then the guided wave propagation in a more complex long-beam butt joint structure is further simulated.展开更多
There are numerous riveting points on the large-sized aircraft panel, irregular row of riveting points on delta wing. It is essential to plan the riveting sequence reasonably to improve the efficiency and accuracy of ...There are numerous riveting points on the large-sized aircraft panel, irregular row of riveting points on delta wing. It is essential to plan the riveting sequence reasonably to improve the efficiency and accuracy of automatic drilling and riveting. Therefore, this article presents a new multi-objective optimization method based on ant colony optimization （ACO）. Multi-objective optimization model of automatic drilling and riveting sequence planning is built by expressing the efficiency and accuracy of riveting as functions of the points＇ coordinates. In order to search the sequences efficiently and improve the quality of the sequences, a new local pheromone updating rule is applied when the ants search sequences. Pareto dominance is incorporated into the proposed ACO to find out the non-dominated sequences. This method is tested on a hyperbolicity panel model of ARJ21 and the result shows its feasibility and superiority compared with particle swarm optimization （PSO） and genetic algorithm （GA）.展开更多
In this paper,self-piercing riveting(SPR)and friction self-piercing riveting(F-SPR)processes were employed to join aluminum alloy AA5182-O sheets.Parallel studies were carried out to compare the two processes in terms...In this paper,self-piercing riveting(SPR)and friction self-piercing riveting(F-SPR)processes were employed to join aluminum alloy AA5182-O sheets.Parallel studies were carried out to compare the two processes in terms of joint macrogeometry,tooling force,microhardness,quasi-static mechanical performance,and fatigue behavior.The results indicate that the F-SPR process formed both rivet–sheet interlocking and sheet–sheet solid-state bonding,whereas the SPR process only contained rivet–sheet interlocking.For the same rivet flaring,the F-SPR process required 63%less tooling force than the SPR process because of the softening effect of frictional heat and the lower rivet hardness of F-SPR.The decrease in the switch depth of the F-SPR resulted in more hardening of the aluminum alloy surrounding the rivet.The higher hardness of aluminum and formation of solid-state bonding enhanced the F-SPR joint stiffness under lap-shear loading,which contributed to the higher quasi-static lap-shear strength and longer fatigue life compared to those of the SPR joints.展开更多
Friction self-piercing riveting(F-SPR)is an emerging technique for low ductility materials joining,which creates a mechanical and solid-state hybrid joint with a semi-hollow rivet.The severe plastic deformation of wor...Friction self-piercing riveting(F-SPR)is an emerging technique for low ductility materials joining,which creates a mechanical and solid-state hybrid joint with a semi-hollow rivet.The severe plastic deformation of work materials and localized elevated temperatures during the F-SPR process yield complex and heterogeneous microstructures.The cut-off action of the work materials by the rivet further complicates the material flow during joint formation.This study employed the F-SPR process to join AA7075-T6 aluminum alloy sheets and systematically investigated the microstructural evolutions using electron backscatter diffraction(EBSD)techniques.The results suggested that as the base material approached the rivet,grains were deformed and recrystallized,forming two distinct fine grain zones(FGZs)surrounding the rivet and in the rivet cavity,re s pectively.Solid-state bonding of aluminum sheets occurred in the FGZs.The formation of FGZ outside the rivet is due to dynamic recrystallization(DRX)triggered by the sliding-to-sticking transition at the rivet/sheet interface.The FGZ in the rivet cavity was caused by the rotation of the trapped aluminum,which created a sticking affected zone at the trapped aluminum/lower sheet interface and led to DRX.Strain rate gradient in the trapped aluminum drove the further expansion of the sticking affected zone and resulted in grain refinement in a larger span.展开更多
With the increasing applications of novel materials and structures in new-generation aircraft,conventional joining techniques in aircraft component assembly are greatly challenged.To meet those challenges,the electrom...With the increasing applications of novel materials and structures in new-generation aircraft,conventional joining techniques in aircraft component assembly are greatly challenged.To meet those challenges,the electromagnetic riveting(EMR)technique was developed as an advanced joining tool,which exhibits obvious advantages in the assembly of new-generation aircraft.In this paper,the riveting principle of EMR was analyzed,and its development history and status were presented in detail.Then,equipment features of three typical EMR systems were given.Moreover,three important applications of EMR were covered,i.e.,composite structure riveting,titanium rivet and large-size aluminum rivet riveting,and interference fit bolt installation.Specially,a novel strengthening method for mechanical linking holes based on EMR was also presented,which can significantly improve the fatigue behaviors of mechanical joints.Finally,open questions in the EMR field were discussed,and some recommendations for future work were also made.This paper can be useful for optimizing the joint designs of aircraft components and improving the level of aircraft maintenance.展开更多
The riveting joint is one of the important joint methods to permanently fasten two thin-walled sheet-metal parts. It is most ba- sic to efficiently analyze and estimate the deformation of the riveting joint for the pe...The riveting joint is one of the important joint methods to permanently fasten two thin-walled sheet-metal parts. It is most ba- sic to efficiently analyze and estimate the deformation of the riveting joint for the performance, fatigue durability and damage of the riveting structure in the aircraft. This paper researches the riveting process mathematics modeling and simulating to more accurately analyze deformation of thin-walled sheet-metal parts. First, the mathematics and mechanics models for the elastic deformation, plastic deformation and springback of the rivet are built by mechanics theory. Second, on the basis of ABAQUS system, a finite element system, an instance made up of the rivet and two thin-walled sheet-metal parts of aluminum alloy is used to analyze and simulate the stress and deformation. What＇s more, a comparison is made between the results obtained by the mathematics and mechanics models and those by finite element method （FEM）. The models are proved true by the calculating and simulation results of the instance.展开更多
Self-piercing riveting(SPR)is a cold forming technique used to fasten together two or more sheets of materials with a rivet without the need to predrill a hole.The application of SPR in the automotive sector has becom...Self-piercing riveting(SPR)is a cold forming technique used to fasten together two or more sheets of materials with a rivet without the need to predrill a hole.The application of SPR in the automotive sector has become increasingly popular mainly due to the growing use of lightweight materials in transportation applications.However,SPR joining of these advanced light materials remains a challenge as these materials often lack a good combination of high strength and ductility to resist the large plastic deformation induced by the SPR process.In this paper,SPR joints of advanced materials and their corresponding failure mechanisms are discussed,aiming to provide the foundation for future improvement of SPR joint quality.This paper is divided into three major sections:1)joint failures focusing on joint defects originated from the SPR process and joint failure modes under different mechanical loading conditions,2)joint corrosion issues,and 3)joint optimisation via process parameters and advanced techniques.展开更多
Self-piercing riveting(SPR)has been widely used in automobile industry,and the strength prediction of SPR joints always attracts the attention of researchers.In this work,a prediction method of the cross-tension stren...Self-piercing riveting(SPR)has been widely used in automobile industry,and the strength prediction of SPR joints always attracts the attention of researchers.In this work,a prediction method of the cross-tension strength of SPR joints was proposed on the basis of finite element(FE)simulation and extreme gradient boosting decision tree(XGBoost)algorithm.An FE model of SPR process was established to simulate the plastic deformations of rivet and substrate materials and verified in terms of cross-sectional dimensions of SPR joints.The residual mechanical field from SPR process simulation was imported into a 2D FE model for the cross-tension testing simulation of SPR joints,and cross-tension strengths from FE simulation show a good consistence with the experiment result.Based on the verified FE model,the mechanical properties and thickness of substrate materials were varied and then used for FE simulation to obtain cross-tension strengths of a number of SPR joints,which were used to train the regression model based on the XGBoost algorithm in order to achieve prediction for cross-tension strength of SPR joints.Results show that the cross-tension strengths of SPR steel/aluminum joints could be successfully predicted by the XGBoost regression model with a respective error less than 7.6%compared to experimental values.展开更多
To fulfill the demands for higher quality,efficiency and flexibility in aviation industry,a multi-functional end effector is designed to automate the drilling and riveting processes in assembling carbon fiber reinforc...To fulfill the demands for higher quality,efficiency and flexibility in aviation industry,a multi-functional end effector is designed to automate the drilling and riveting processes in assembling carbon fiber reinforced polymer(CFRP)and aluminum components for a robotic aircraft assembly system.To meet the specific functional requirements for blind rivet installation on CFRP and aluminum materials,additional modules are incorporated on the end effector aside of the basic processing modules for drilling.And all of these processing modules allow for a onestep-drilling-countersinking process,hole inspection,automatic rivet feed,rivet geometry check,sealant application,rivet insertion and installation.Besides,to guarantee the better quality of the hole drilled and joints riveted,several online detection and adjustment measures are applied to this end effector,including the reference detection and perpendicular calibration,which could effectively ensure the positioning precision and perpendicular accuracy as demanded.Finally,the test result shows that this end effector is capable of producing each hole to a positioning precision within ±0.5 mm,aperpendicular accuracy within 0.3°,a diameter tolerance of H8,and a countersink depth tolerance of±0.01 mm.Moreover,it could drill and rivet up to three joints per minute,with acceptable shearing and tensile strength.展开更多
The concave die design of self-pierce riveting(SPR) is of critical importance for product quality. The optimization of concave die parameters based on orthogonal test is proposed to explore the relationship between se...The concave die design of self-pierce riveting(SPR) is of critical importance for product quality. The optimization of concave die parameters based on orthogonal test is proposed to explore the relationship between self-pierce riveted joint quality and die parameters. There are nine independent die parameter factors in orthogonal test and each factor has 4 levels. In order to evaluate the interlock and neck thickness, we carry out numerical simulations by the software DEFORM-2D. Then, the primary and secondary factors that affect the joint quality have been found out by means of range analysis. Finally, an optimization scheme is brought forward to design concave die in SPR process, which indicates that the joint has higher quality than that of former orthogonal tests.This work can be extended by a detailed mechanical and fatigue analysis for the joint quality of SPR process.展开更多
A recently developed friction self-piercing riveting(F-SPR)technique based on the combination of fric-tion stir processing and riveting has been reported to possess both solid-state bonding and mechanical fastening ch...A recently developed friction self-piercing riveting(F-SPR)technique based on the combination of fric-tion stir processing and riveting has been reported to possess both solid-state bonding and mechanical fastening characteristics.However,there is still a lack of quantitative understanding of the hybrid en-hancement mechanism,hindering its engineering application.To fill in this gap,the current research investigated the microstructure evolution,microhardness distribution,and miniature-tensile performance of the aluminum alloy AA7075-T6 F-SPR joints by experiments.An accurate numerical simulation model was established to quantitatively evaluate the individual contributions of microstructure,local bonding strength,and macro interlocking to the performance of the joint,which could well explain the experi-mental results.It was found that due to the friction stirring of the rivet,solid-state bonding driven by dynamic recrystallization is realized between the trapped aluminum in the rivet cavity and the bottom aluminum sheet.The solid-state bonding zone has 75%yield strength,81%ultimate tensile strength,and 106%elongation compared to the base material.This solid-state bonding enables the internal interlock-ing between the trapped aluminum and the rivet to withstand the additional load,which forms a novel dual-interlock fastening mechanism and increases the peak cross-tension force by 14.3%compared to the single-interlock joint.展开更多
Carbon fiber reinforced polymer(CFRP) and AZ31B Mg alloy were joined by the friction self-piercing riveting(F-SPR) with different steel rivet shank sizes. With the increase of rivet shank size, lap shear fracture load...Carbon fiber reinforced polymer(CFRP) and AZ31B Mg alloy were joined by the friction self-piercing riveting(F-SPR) with different steel rivet shank sizes. With the increase of rivet shank size, lap shear fracture load and mechanical interlock distance increased. Ultrafine grains were formed at the joint in AZ31B as a result of dynamic recrystallization, which contributed to the higher hardness. Fatigue life of the CFRP-AZ31B joint was studied at various peak loads of 0.5, 1, 2, and 3 kN and compared with the resistance spot welded AZ31B-AZ31B from the open literature. The fatigue performance was better at higher peak load(>2 kN) and comparable to that of resistance spot welding of AZ31B to AZ31B at lower peak loads(<1 kN). From fractography, the crack initiation for lower peak load(<1 kN) case was observed at the fretting positions on the top and bottom surfaces of AZ31B sheet. When peak load was increased, fretting between the rivet and the top of AZ31B became more dominant to initiate a crack during fatigue testing.展开更多
A new testing methodology was developed to quantitively study galvanic corrosion of AZ31B and thermoset carbon-fiber–reinforced polymer spot-joined by a friction self-piercing riveting process.Pre-defined areas of AZ...A new testing methodology was developed to quantitively study galvanic corrosion of AZ31B and thermoset carbon-fiber–reinforced polymer spot-joined by a friction self-piercing riveting process.Pre-defined areas of AZ31B in the joint were exposed in 0.1 M NaCl solution over time.Massive galvanic corrosion of AZ31B was observed as exposure time increased.The measured volume loss was converted into corrosion current that was at least 48 times greater than the corrosion current of AZ31B without galvanic coupling.Ninety percent of the mechanical joint integrity was retained for corroded F-SPR joints to 200 h and then decreased because of the massive volume loss of AZ31B。展开更多
Carbon fiber reinforced plastic(CFRP)and aluminum stacks are widely used in aviation industry due to light weight and high performance.Millions of rivet holes need to be drilled on body materials,and more than 80%of f...Carbon fiber reinforced plastic(CFRP)and aluminum stacks are widely used in aviation industry due to light weight and high performance.Millions of rivet holes need to be drilled on body materials,and more than 80%of fatigue cracks occur at the connection holes,so the damage and residual stress of hole surface have crucial effect on the riveting fatigue life of CFRP/aluminum stacks and the flight performance.Recently,robotic rotary ultrasonic drilling(RRUD)technology is a promising method to machine the stacks.However,the hole surface strengthening mechanism in RRUD and the service performance of the riveting joint are not verified.Thus,in this paper,the hole surface strengthening mechanism of RRUD for CFRP/aluminum stacks is investigated,a theoretical residual stress model is established,and the fatigue life experiment of riveted joints is conducted.Firstly,analysis on residual stress in RRUD is carried out with consideration of strengthening force and cutting temperature.Residual stress model is established based on the calculation of elastic stress,plastic stress and stress release.Validation experiment results show that ultrasonic vibration changes residual stress from tensile stress to compressive stress.At the same time,comparative damage analysis of CFRP hole exit and hole surface in robotic conventional drilling(RCD)and RRUD is presented.Finally,fatigue strength experiments of riveted joints are conducted for performance verification.Experimental results indicate that fatigue life of single-hole riveted joints is increased by 68%with ultrasonic vibration,and four-hole riveted joint arranged according to aerospace design standards is increased by more than 86%.展开更多
Friction self-piercing riveting(F-SPR)process based on a pip die has been invented to solve the cracking problems in riveting high-strength and low-ductility light metals,such as magnesium alloys,cast aluminum,and 7 s...Friction self-piercing riveting(F-SPR)process based on a pip die has been invented to solve the cracking problems in riveting high-strength and low-ductility light metals,such as magnesium alloys,cast aluminum,and 7 series aluminum alloys.In this paper,in order to solve quality issues caused by the misalignment between rivet and pip-die in F-SPR,a flat-die based F-SPR process was proposed and employed to join 1.27 mm-thick AA6061-T6 to 3 mm-thick AZ31B.The results indicate that a 1.0 mm die distance is effective to avoid rivet upset and insufficient flaring.As the feed rate increases,the heat input in the whole process decreases,resulting in a larger riveting force,which in turn increases both the bottom thickness and interlock amount.Besides,solid-state bonding,including Al-Mg intermetallic compounds(IMCs),Al-Mg mechanical mixture,and Al-Fe atom interdiffusion was observed at the joint interfaces.The upper Al layer was softened,but the lower Mg layer was hardened,and both sheets exhibited a narrowed affected region with the increase of feed rate,while the rivet hardness shows no obvious change.Three fracture modes appeared accompanying the variations in lap-shear strength and energy absorption as the feed rate increased from 2 mm/s to 8 mm/s.Finally,the F-SPR process using a flat die was compared to those using a pip die and a flat bottom die to show the advantage of flat die on coping with the misalignment problem.展开更多
The application of magnesium alloys to automobiles is increasing due to their superior specific strength and specific stiffness.In this study,an upper sheet of AZ31 magnesium alloy and a lower sheet of cold-rolled ste...The application of magnesium alloys to automobiles is increasing due to their superior specific strength and specific stiffness.In this study,an upper sheet of AZ31 magnesium alloy and a lower sheet of cold-rolled steel were joined by self-piercing riveting(SPR),a method commonly used to join automotive panels.A cross-shaped specimen was fabricated with a punching force of 35 kN,which exhibited the best joint strength for the SPR joint specimen geometry.Monotonic and fatigue strengths were evaluated using cross-shaped specimens at loading angles of 0°,45°,and 90°.The load amplitude corresponding to the fatigue endurance limit was assumed to be at 106 cycles,and the fatigue ratios(=fatigue endurance limit/static strength)at the loading angles of 0°,45°,and 90°are 22%,13%,and 9%,respectively.For all three loading angle specimens,fatigue cracks initiated at the triple point where the rivet shank,the upper sheet and the lower sheet are in contact with each other,with the cracks propagating through the thickness of the upper sheet and ultimately leading to fracture.The fatigue lifetimes were evaluated through the von-Mises stress,maximum principal stress,and equivalent stress intensity factor.It was found that the fatigue lifetimes could be evaluated most appropriately through the maximum principal stress.展开更多
To extend the service life of the clinched joint,a reconditioning process conducted with an additional tubular rivet was proposed in this work.Different reconditioning forces were employed to produce dissimilar recond...To extend the service life of the clinched joint,a reconditioning process conducted with an additional tubular rivet was proposed in this work.Different reconditioning forces were employed to produce dissimilar reconditioned joints by experimental method.The experimental results indicated that the neck fracture was the common failure mode of both original clinched and reconditioned joints.Compared with the original clinched joint,the shearing strength of the reconditioned joint produced by a reconditioning force of 40 kN increased from 1810.5 to 1986.47 N,and the energy absorption increased from 2.34 to 3.46 J.The range of effective reconditioning force was from 35 to 40 kN and 40 kN was the best choice for reconditioning the AA5052 failed joints.The mechanical properties of the reconditioned joints are obviously better than those of the original clinched joints,which fully demonstrates that the reconditioning method proposed in this work has a broad prospect of industrial application.展开更多
Static tensile and fatigue tests were performed on shear and tensile self-piercing riveted aluminium-steel structures to evaluate their mechanical and fatigue properties. The influences of the thickness and the streng...Static tensile and fatigue tests were performed on shear and tensile self-piercing riveted aluminium-steel structures to evaluate their mechanical and fatigue properties. The influences of the thickness and the strength of the high strength steel on mechanical and fatigue performances were investigated based on the tensile and F-N curves of the joints. The results show that mechanical and fatigue properties of the shear self-piercing riveted joints are much better than those of the tensile self-piercing riveted joints. Mechanical and fatigue performances of the two joints were significantly influenced by the thickness and strength of the steel sheet, and were markedly improved when the thickness of steel sheet increased. The steel strength showed significantly different effects on shear and tensile riveted structures, i. e. , when the steel strength increased, the strength of the shear structure greatly increased while the tensile structure just had a slight increase in the strength. Fatigue failure generally occurred in the sheet materials and the fatigue crack location changed with increasing the sheet thickness and the sheet strength.展开更多
A new friction-based riveting technique, Rotating Hammer Riveting(RHR), is demonstrated to fully form AZ31 Mg rivet heads in a mere 0.23 s. Heat and pressure generated through severe plastic deformation during the pro...A new friction-based riveting technique, Rotating Hammer Riveting(RHR), is demonstrated to fully form AZ31 Mg rivet heads in a mere 0.23 s. Heat and pressure generated through severe plastic deformation during the process was sufficient to form the Mg rivet head without the need for a pre-heating operation. Due to preliminary twinning and followed by dynamic recrystallization, AZ31 Mg grains in the rivet head were refined during RHR, which enhance the formability of Mg rivets by triggering grain boundary sliding and reducing plastic anisotropy of Mg. In addition, RHR joints showed a metallurgical bond between the rivet head and top AZ31 Mg sheet, which eliminates a significant pathway for corrosion.展开更多
Most researches on the static performance of stiffened panel joined by friction stir welding（FSW） mainly focus on the compression stability rather than shear stability. To evaluate the potential of FSW as a replacem...Most researches on the static performance of stiffened panel joined by friction stir welding（FSW） mainly focus on the compression stability rather than shear stability. To evaluate the potential of FSW as a replacement for traditional rivet fastening for stiffened panel assembly in aviation application, finite element method（FEM） is applied to compare compression and shear stability performances of FSW stiffened panels with stability performances of riveted stiffened panels. FEMs of 2024-T3 aluminum alloy FSW and riveted stiffened panels are developed and nonlinear static analysis method is applied to obtain buckling pattern, buckling load and load carrying capability of each panel model. The accuracy of each FEM of FSW stiffened panel is evaluated by stability experiment of FSW stiffened panel specimens with identical geometry and boundary condition and the accuracy of each FEM of riveted stiffened panel is evaluated by semi-empirical calculation formulas. It is found that FEMs without considering weld-induced initial imperfections notably overestimate the static strengths of FSW stiffened panels. FEM results show that, buckling patterns of both FSW and riveted compression stiffened panels represent local buckling of plate between stiffeners. The initial buckling waves of FSW stiffened panel emerge uniformly in each plate between stiffeners while those of riveted panel mainly emerge in the mid-plate. Buckling patterns of both FSW and riveted shear stiffened panels represent local buckling of plate close to the loading corner. FEM results indicate that, shear buckling of FSW stiffened panel is less sensitive to the initial imperfections than compression buckling. Load carrying capability of FSW stiffened panel is less sensitive to the initial imperfections than initial buckling. It can be concluded that buckling loads of FSW panels are a bit lower than those of riveted panels whereas carrying capabilities of FSW panels are almost equivalent to those of riveted panels with identical geometries. Finite element method for simulating static performances of FSW and riveted stiffened panels is proposed and evaluated and some beneficial conclusions are obtained, which offer useful references for analysis and application of FSW to replace rivet fastening in aviation stiffened panel assembly.展开更多
文摘Multi-layer riveted structures are widely applied to aircraft.During the service,cracks may appear within these structures due to stress concentration of the riveted holes.The guided wave monitoring has been proved to be an effective tool to deal with this problem.However,there is a lack of understanding of the wave propagation process across such kinds of structures.This study proposes a piezoelectric guided wave simulation method to reveal the propagation of guided waves in multi-layer riveted structures.Effects of pretension force,friction coefficient,and cracks that might influence wave characteristics are studied.The guided wave simulation data is compared with the experimental results and the results verify the simulation model.Then the guided wave propagation in a more complex long-beam butt joint structure is further simulated.
基金National Natural Science Foundation of China (50805119)Aeronautical Science Foundation of China (2009ZE53)
文摘There are numerous riveting points on the large-sized aircraft panel, irregular row of riveting points on delta wing. It is essential to plan the riveting sequence reasonably to improve the efficiency and accuracy of automatic drilling and riveting. Therefore, this article presents a new multi-objective optimization method based on ant colony optimization （ACO）. Multi-objective optimization model of automatic drilling and riveting sequence planning is built by expressing the efficiency and accuracy of riveting as functions of the points＇ coordinates. In order to search the sequences efficiently and improve the quality of the sequences, a new local pheromone updating rule is applied when the ants search sequences. Pareto dominance is incorporated into the proposed ACO to find out the non-dominated sequences. This method is tested on a hyperbolicity panel model of ARJ21 and the result shows its feasibility and superiority compared with particle swarm optimization （PSO） and genetic algorithm （GA）.
基金The authors would like to acknowledge the financial support of the National Natural Science Foundation of China(52025058 and U1764251)the National Key Research and Development Program of China(2016YFB0101606-8).
文摘In this paper,self-piercing riveting(SPR)and friction self-piercing riveting(F-SPR)processes were employed to join aluminum alloy AA5182-O sheets.Parallel studies were carried out to compare the two processes in terms of joint macrogeometry,tooling force,microhardness,quasi-static mechanical performance,and fatigue behavior.The results indicate that the F-SPR process formed both rivet–sheet interlocking and sheet–sheet solid-state bonding,whereas the SPR process only contained rivet–sheet interlocking.For the same rivet flaring,the F-SPR process required 63%less tooling force than the SPR process because of the softening effect of frictional heat and the lower rivet hardness of F-SPR.The decrease in the switch depth of the F-SPR resulted in more hardening of the aluminum alloy surrounding the rivet.The higher hardness of aluminum and formation of solid-state bonding enhanced the F-SPR joint stiffness under lap-shear loading,which contributed to the higher quasi-static lap-shear strength and longer fatigue life compared to those of the SPR joints.
基金financial support of the National Natural Science Foundation of China(Grant Nos.52025058 and U1764251)the National Key Research and Development Program of China(Grant No.2016YFB0101606-08)+1 种基金Shanghai Jiao Tong Universityfinancially supported by Project to Create Research and Educational Hubs for Innovative Manufacturing in Asia,Joining and Welding Research Institute,Osaka University。
文摘Friction self-piercing riveting(F-SPR)is an emerging technique for low ductility materials joining,which creates a mechanical and solid-state hybrid joint with a semi-hollow rivet.The severe plastic deformation of work materials and localized elevated temperatures during the F-SPR process yield complex and heterogeneous microstructures.The cut-off action of the work materials by the rivet further complicates the material flow during joint formation.This study employed the F-SPR process to join AA7075-T6 aluminum alloy sheets and systematically investigated the microstructural evolutions using electron backscatter diffraction(EBSD)techniques.The results suggested that as the base material approached the rivet,grains were deformed and recrystallized,forming two distinct fine grain zones(FGZs)surrounding the rivet and in the rivet cavity,re s pectively.Solid-state bonding of aluminum sheets occurred in the FGZs.The formation of FGZ outside the rivet is due to dynamic recrystallization(DRX)triggered by the sliding-to-sticking transition at the rivet/sheet interface.The FGZ in the rivet cavity was caused by the rotation of the trapped aluminum,which created a sticking affected zone at the trapped aluminum/lower sheet interface and led to DRX.Strain rate gradient in the trapped aluminum drove the further expansion of the sticking affected zone and resulted in grain refinement in a larger span.
基金funded by the Major National Research Project of Numerical Control Machine and Basic Manufacturing Equipment of China(No.2016ZX04002004-008).
文摘With the increasing applications of novel materials and structures in new-generation aircraft,conventional joining techniques in aircraft component assembly are greatly challenged.To meet those challenges,the electromagnetic riveting(EMR)technique was developed as an advanced joining tool,which exhibits obvious advantages in the assembly of new-generation aircraft.In this paper,the riveting principle of EMR was analyzed,and its development history and status were presented in detail.Then,equipment features of three typical EMR systems were given.Moreover,three important applications of EMR were covered,i.e.,composite structure riveting,titanium rivet and large-size aluminum rivet riveting,and interference fit bolt installation.Specially,a novel strengthening method for mechanical linking holes based on EMR was also presented,which can significantly improve the fatigue behaviors of mechanical joints.Finally,open questions in the EMR field were discussed,and some recommendations for future work were also made.This paper can be useful for optimizing the joint designs of aircraft components and improving the level of aircraft maintenance.
基金National Natural Science Foundation of China （50805119） Aeronautical Science Foundation in China （2010ZE53049） Fund of National Engineering and Research Center for Commercial Aircraft Manufacturing （SAMC11 -JS-07-200）
文摘The riveting joint is one of the important joint methods to permanently fasten two thin-walled sheet-metal parts. It is most ba- sic to efficiently analyze and estimate the deformation of the riveting joint for the performance, fatigue durability and damage of the riveting structure in the aircraft. This paper researches the riveting process mathematics modeling and simulating to more accurately analyze deformation of thin-walled sheet-metal parts. First, the mathematics and mechanics models for the elastic deformation, plastic deformation and springback of the rivet are built by mechanics theory. Second, on the basis of ABAQUS system, a finite element system, an instance made up of the rivet and two thin-walled sheet-metal parts of aluminum alloy is used to analyze and simulate the stress and deformation. What＇s more, a comparison is made between the results obtained by the mathematics and mechanics models and those by finite element method （FEM）. The models are proved true by the calculating and simulation results of the instance.
文摘Self-piercing riveting(SPR)is a cold forming technique used to fasten together two or more sheets of materials with a rivet without the need to predrill a hole.The application of SPR in the automotive sector has become increasingly popular mainly due to the growing use of lightweight materials in transportation applications.However,SPR joining of these advanced light materials remains a challenge as these materials often lack a good combination of high strength and ductility to resist the large plastic deformation induced by the SPR process.In this paper,SPR joints of advanced materials and their corresponding failure mechanisms are discussed,aiming to provide the foundation for future improvement of SPR joint quality.This paper is divided into three major sections:1)joint failures focusing on joint defects originated from the SPR process and joint failure modes under different mechanical loading conditions,2)joint corrosion issues,and 3)joint optimisation via process parameters and advanced techniques.
基金Supported by National Natural Science Foundation of China(Grant No.51805375).
文摘Self-piercing riveting(SPR)has been widely used in automobile industry,and the strength prediction of SPR joints always attracts the attention of researchers.In this work,a prediction method of the cross-tension strength of SPR joints was proposed on the basis of finite element(FE)simulation and extreme gradient boosting decision tree(XGBoost)algorithm.An FE model of SPR process was established to simulate the plastic deformations of rivet and substrate materials and verified in terms of cross-sectional dimensions of SPR joints.The residual mechanical field from SPR process simulation was imported into a 2D FE model for the cross-tension testing simulation of SPR joints,and cross-tension strengths from FE simulation show a good consistence with the experiment result.Based on the verified FE model,the mechanical properties and thickness of substrate materials were varied and then used for FE simulation to obtain cross-tension strengths of a number of SPR joints,which were used to train the regression model based on the XGBoost algorithm in order to achieve prediction for cross-tension strength of SPR joints.Results show that the cross-tension strengths of SPR steel/aluminum joints could be successfully predicted by the XGBoost regression model with a respective error less than 7.6%compared to experimental values.
基金supported by the National Natural Science Foundations of China(Nos.5157051626,51475225)
文摘To fulfill the demands for higher quality,efficiency and flexibility in aviation industry,a multi-functional end effector is designed to automate the drilling and riveting processes in assembling carbon fiber reinforced polymer(CFRP)and aluminum components for a robotic aircraft assembly system.To meet the specific functional requirements for blind rivet installation on CFRP and aluminum materials,additional modules are incorporated on the end effector aside of the basic processing modules for drilling.And all of these processing modules allow for a onestep-drilling-countersinking process,hole inspection,automatic rivet feed,rivet geometry check,sealant application,rivet insertion and installation.Besides,to guarantee the better quality of the hole drilled and joints riveted,several online detection and adjustment measures are applied to this end effector,including the reference detection and perpendicular calibration,which could effectively ensure the positioning precision and perpendicular accuracy as demanded.Finally,the test result shows that this end effector is capable of producing each hole to a positioning precision within ±0.5 mm,aperpendicular accuracy within 0.3°,a diameter tolerance of H8,and a countersink depth tolerance of±0.01 mm.Moreover,it could drill and rivet up to three joints per minute,with acceptable shearing and tensile strength.
基金the National Natural Science Foundation of China(No.51375282)the China Postdoctoral Science Foundation(No.2012T50621)the Open Fund of Shanghai Key Laboratory of Digital Manufacture for Thin-walled Structures(No.2011003)
文摘The concave die design of self-pierce riveting(SPR) is of critical importance for product quality. The optimization of concave die parameters based on orthogonal test is proposed to explore the relationship between self-pierce riveted joint quality and die parameters. There are nine independent die parameter factors in orthogonal test and each factor has 4 levels. In order to evaluate the interlock and neck thickness, we carry out numerical simulations by the software DEFORM-2D. Then, the primary and secondary factors that affect the joint quality have been found out by means of range analysis. Finally, an optimization scheme is brought forward to design concave die in SPR process, which indicates that the joint has higher quality than that of former orthogonal tests.This work can be extended by a detailed mechanical and fatigue analysis for the joint quality of SPR process.
基金support of the National Natural Science Foundation of China(Grant Nos.52025058 and U1764251)the State Key Laboratory of Mechan-ical System and Vibration(Grant No.MSVZD202111)+1 种基金the Japan Society for the Promotion of Science(JSPS)KAKENHI(Grant No.21K14439)Shanghai Jiao Tong University.
文摘A recently developed friction self-piercing riveting(F-SPR)technique based on the combination of fric-tion stir processing and riveting has been reported to possess both solid-state bonding and mechanical fastening characteristics.However,there is still a lack of quantitative understanding of the hybrid en-hancement mechanism,hindering its engineering application.To fill in this gap,the current research investigated the microstructure evolution,microhardness distribution,and miniature-tensile performance of the aluminum alloy AA7075-T6 F-SPR joints by experiments.An accurate numerical simulation model was established to quantitatively evaluate the individual contributions of microstructure,local bonding strength,and macro interlocking to the performance of the joint,which could well explain the experi-mental results.It was found that due to the friction stirring of the rivet,solid-state bonding driven by dynamic recrystallization is realized between the trapped aluminum in the rivet cavity and the bottom aluminum sheet.The solid-state bonding zone has 75%yield strength,81%ultimate tensile strength,and 106%elongation compared to the base material.This solid-state bonding enables the internal interlock-ing between the trapped aluminum and the rivet to withstand the additional load,which forms a novel dual-interlock fastening mechanism and increases the peak cross-tension force by 14.3%compared to the single-interlock joint.
基金financially sponsored by the US Department Energy Vehicle Technologies Office, as part of the Joining Core Program。
文摘Carbon fiber reinforced polymer(CFRP) and AZ31B Mg alloy were joined by the friction self-piercing riveting(F-SPR) with different steel rivet shank sizes. With the increase of rivet shank size, lap shear fracture load and mechanical interlock distance increased. Ultrafine grains were formed at the joint in AZ31B as a result of dynamic recrystallization, which contributed to the higher hardness. Fatigue life of the CFRP-AZ31B joint was studied at various peak loads of 0.5, 1, 2, and 3 kN and compared with the resistance spot welded AZ31B-AZ31B from the open literature. The fatigue performance was better at higher peak load(>2 kN) and comparable to that of resistance spot welding of AZ31B to AZ31B at lower peak loads(<1 kN). From fractography, the crack initiation for lower peak load(<1 kN) case was observed at the fretting positions on the top and bottom surfaces of AZ31B sheet. When peak load was increased, fretting between the rivet and the top of AZ31B became more dominant to initiate a crack during fatigue testing.
基金financially sponsored by the US Department Energy Vehicle Technologies Office, as part of the Joining Core Programmanaged by UT-Battelle LLC for the US Department of Energy under Contract DE-AC05-00OR22725。
文摘A new testing methodology was developed to quantitively study galvanic corrosion of AZ31B and thermoset carbon-fiber–reinforced polymer spot-joined by a friction self-piercing riveting process.Pre-defined areas of AZ31B in the joint were exposed in 0.1 M NaCl solution over time.Massive galvanic corrosion of AZ31B was observed as exposure time increased.The measured volume loss was converted into corrosion current that was at least 48 times greater than the corrosion current of AZ31B without galvanic coupling.Ninety percent of the mechanical joint integrity was retained for corroded F-SPR joints to 200 h and then decreased because of the massive volume loss of AZ31B。
基金the the Project on the Technological Leading Talent Teams Led by Frontiers Science Center for Complex Equipment System Dynamics(No.FSCCESD220401)the Jiangsu Funding Program for Excellent Postdoctoral Talent(No.2022ZB264).
文摘Carbon fiber reinforced plastic(CFRP)and aluminum stacks are widely used in aviation industry due to light weight and high performance.Millions of rivet holes need to be drilled on body materials,and more than 80%of fatigue cracks occur at the connection holes,so the damage and residual stress of hole surface have crucial effect on the riveting fatigue life of CFRP/aluminum stacks and the flight performance.Recently,robotic rotary ultrasonic drilling(RRUD)technology is a promising method to machine the stacks.However,the hole surface strengthening mechanism in RRUD and the service performance of the riveting joint are not verified.Thus,in this paper,the hole surface strengthening mechanism of RRUD for CFRP/aluminum stacks is investigated,a theoretical residual stress model is established,and the fatigue life experiment of riveted joints is conducted.Firstly,analysis on residual stress in RRUD is carried out with consideration of strengthening force and cutting temperature.Residual stress model is established based on the calculation of elastic stress,plastic stress and stress release.Validation experiment results show that ultrasonic vibration changes residual stress from tensile stress to compressive stress.At the same time,comparative damage analysis of CFRP hole exit and hole surface in robotic conventional drilling(RCD)and RRUD is presented.Finally,fatigue strength experiments of riveted joints are conducted for performance verification.Experimental results indicate that fatigue life of single-hole riveted joints is increased by 68%with ultrasonic vibration,and four-hole riveted joint arranged according to aerospace design standards is increased by more than 86%.
基金financial support of the National Natural Science Foundation of China(Grant Nos.52025058 and U1764251)。
文摘Friction self-piercing riveting(F-SPR)process based on a pip die has been invented to solve the cracking problems in riveting high-strength and low-ductility light metals,such as magnesium alloys,cast aluminum,and 7 series aluminum alloys.In this paper,in order to solve quality issues caused by the misalignment between rivet and pip-die in F-SPR,a flat-die based F-SPR process was proposed and employed to join 1.27 mm-thick AA6061-T6 to 3 mm-thick AZ31B.The results indicate that a 1.0 mm die distance is effective to avoid rivet upset and insufficient flaring.As the feed rate increases,the heat input in the whole process decreases,resulting in a larger riveting force,which in turn increases both the bottom thickness and interlock amount.Besides,solid-state bonding,including Al-Mg intermetallic compounds(IMCs),Al-Mg mechanical mixture,and Al-Fe atom interdiffusion was observed at the joint interfaces.The upper Al layer was softened,but the lower Mg layer was hardened,and both sheets exhibited a narrowed affected region with the increase of feed rate,while the rivet hardness shows no obvious change.Three fracture modes appeared accompanying the variations in lap-shear strength and energy absorption as the feed rate increased from 2 mm/s to 8 mm/s.Finally,the F-SPR process using a flat die was compared to those using a pip die and a flat bottom die to show the advantage of flat die on coping with the misalignment problem.
基金This study was supported by the Research Program funded by the SeoulTech(Seoul National University of Science&Technology).
文摘The application of magnesium alloys to automobiles is increasing due to their superior specific strength and specific stiffness.In this study,an upper sheet of AZ31 magnesium alloy and a lower sheet of cold-rolled steel were joined by self-piercing riveting(SPR),a method commonly used to join automotive panels.A cross-shaped specimen was fabricated with a punching force of 35 kN,which exhibited the best joint strength for the SPR joint specimen geometry.Monotonic and fatigue strengths were evaluated using cross-shaped specimens at loading angles of 0°,45°,and 90°.The load amplitude corresponding to the fatigue endurance limit was assumed to be at 106 cycles,and the fatigue ratios(=fatigue endurance limit/static strength)at the loading angles of 0°,45°,and 90°are 22%,13%,and 9%,respectively.For all three loading angle specimens,fatigue cracks initiated at the triple point where the rivet shank,the upper sheet and the lower sheet are in contact with each other,with the cracks propagating through the thickness of the upper sheet and ultimately leading to fracture.The fatigue lifetimes were evaluated through the von-Mises stress,maximum principal stress,and equivalent stress intensity factor.It was found that the fatigue lifetimes could be evaluated most appropriately through the maximum principal stress.
基金financial supports from the National Natural Science Foundation of China (No. 51805416)the Young Elite Scientists Sponsorship Program by CAST, China (No. YESS20200279)+3 种基金the Natural Science Foundation of Hunan Province, China (No. 2020JJ5716)the Project of State Key Laboratory of High Performance Complex Manufacturing, Central South University, China (No. ZZYJKT2019-01)the Hunan Provincial Natural Science Foundation for Excellent Young Scholars, China (No. 2021JJ20059)the Huxiang High-Level Talent Gathering Project of Hunan Province, China (No. 2019RS1002)。
文摘To extend the service life of the clinched joint,a reconditioning process conducted with an additional tubular rivet was proposed in this work.Different reconditioning forces were employed to produce dissimilar reconditioned joints by experimental method.The experimental results indicated that the neck fracture was the common failure mode of both original clinched and reconditioned joints.Compared with the original clinched joint,the shearing strength of the reconditioned joint produced by a reconditioning force of 40 kN increased from 1810.5 to 1986.47 N,and the energy absorption increased from 2.34 to 3.46 J.The range of effective reconditioning force was from 35 to 40 kN and 40 kN was the best choice for reconditioning the AA5052 failed joints.The mechanical properties of the reconditioned joints are obviously better than those of the original clinched joints,which fully demonstrates that the reconditioning method proposed in this work has a broad prospect of industrial application.
基金supported by Key Technologies Research and Development (R & D) Program of Anhui Province of China (1604a0902134)the Key Discipline Team (AKZDXK2015C03 )the Anhui University Provincial Natural Science Research Projects(KJ2016A181 and KJ2016A183)
文摘Static tensile and fatigue tests were performed on shear and tensile self-piercing riveted aluminium-steel structures to evaluate their mechanical and fatigue properties. The influences of the thickness and the strength of the high strength steel on mechanical and fatigue performances were investigated based on the tensile and F-N curves of the joints. The results show that mechanical and fatigue properties of the shear self-piercing riveted joints are much better than those of the tensile self-piercing riveted joints. Mechanical and fatigue performances of the two joints were significantly influenced by the thickness and strength of the steel sheet, and were markedly improved when the thickness of steel sheet increased. The steel strength showed significantly different effects on shear and tensile riveted structures, i. e. , when the steel strength increased, the strength of the shear structure greatly increased while the tensile structure just had a slight increase in the strength. Fatigue failure generally occurred in the sheet materials and the fatigue crack location changed with increasing the sheet thickness and the sheet strength.
基金the support of the U.S.Department of Energy Vehicle Technologies Office(DOE/VTO)Joining Core Program。
文摘A new friction-based riveting technique, Rotating Hammer Riveting(RHR), is demonstrated to fully form AZ31 Mg rivet heads in a mere 0.23 s. Heat and pressure generated through severe plastic deformation during the process was sufficient to form the Mg rivet head without the need for a pre-heating operation. Due to preliminary twinning and followed by dynamic recrystallization, AZ31 Mg grains in the rivet head were refined during RHR, which enhance the formability of Mg rivets by triggering grain boundary sliding and reducing plastic anisotropy of Mg. In addition, RHR joints showed a metallurgical bond between the rivet head and top AZ31 Mg sheet, which eliminates a significant pathway for corrosion.
文摘Most researches on the static performance of stiffened panel joined by friction stir welding（FSW） mainly focus on the compression stability rather than shear stability. To evaluate the potential of FSW as a replacement for traditional rivet fastening for stiffened panel assembly in aviation application, finite element method（FEM） is applied to compare compression and shear stability performances of FSW stiffened panels with stability performances of riveted stiffened panels. FEMs of 2024-T3 aluminum alloy FSW and riveted stiffened panels are developed and nonlinear static analysis method is applied to obtain buckling pattern, buckling load and load carrying capability of each panel model. The accuracy of each FEM of FSW stiffened panel is evaluated by stability experiment of FSW stiffened panel specimens with identical geometry and boundary condition and the accuracy of each FEM of riveted stiffened panel is evaluated by semi-empirical calculation formulas. It is found that FEMs without considering weld-induced initial imperfections notably overestimate the static strengths of FSW stiffened panels. FEM results show that, buckling patterns of both FSW and riveted compression stiffened panels represent local buckling of plate between stiffeners. The initial buckling waves of FSW stiffened panel emerge uniformly in each plate between stiffeners while those of riveted panel mainly emerge in the mid-plate. Buckling patterns of both FSW and riveted shear stiffened panels represent local buckling of plate close to the loading corner. FEM results indicate that, shear buckling of FSW stiffened panel is less sensitive to the initial imperfections than compression buckling. Load carrying capability of FSW stiffened panel is less sensitive to the initial imperfections than initial buckling. It can be concluded that buckling loads of FSW panels are a bit lower than those of riveted panels whereas carrying capabilities of FSW panels are almost equivalent to those of riveted panels with identical geometries. Finite element method for simulating static performances of FSW and riveted stiffened panels is proposed and evaluated and some beneficial conclusions are obtained, which offer useful references for analysis and application of FSW to replace rivet fastening in aviation stiffened panel assembly.
