This paper investigates the effect of hydrogen on the transformation ratcheting of NiTi shape memory alloy(SMA)wires in the experimental and theoretical aspects.In the aspect of experiments,the NiTi SMA orthodontic wi...This paper investigates the effect of hydrogen on the transformation ratcheting of NiTi shape memory alloy(SMA)wires in the experimental and theoretical aspects.In the aspect of experiments,the NiTi SMA orthodontic wires are hydrogen charged by the electrochemical charging method at room temperature with varying charging durations and charging lengths.After that,the ex-situ cyclic tension-unloading experiments are performed for the charged and non-charged wires.Experimental results reveal that the two transformation platforms(two-step MT)occur during the forward MT at the beginning and end of cyclic deformation for hydrogen-charged wires,which can be regarded as a global response of the non-charged and charged regions.Furthermore,this two-step MT and transformation ratcheting aggravate with the increase of the charging duration.In the aspect of the theoretical model,a diffusional-mechanically coupled constitutive model is developed.In this constitutive model,the strain is considered as four components:elasticity,transformation(MT),hydrogen expansion and transformation-induced plasticity(TRIP).Combining Helmholtz free energy and Clausius–Duhem inequality,the thermodynamic driving forces of MT and TRIP are obtained.Fick’s law and the mass conservation equation are incorporated to derive the evolution of hydrogen concentration.A transition from material points to the whole wire is employed to extend the model from a material point to the entire wire,and the overall response with a heterogeneous hydrogen concentration field is obtained.The proposed model's ability to predict the transformation ratcheting of the non-charged and charged NiTi SMA wires is verified by contrasting predictions and experimental results.展开更多
The behavior of rolling contact fatigue (RCF) of medium carbon bainitic back-up roll steel was investigated under its actual work conditions. A kind of asperity-scale surface originated cracks, which is lying parallel...The behavior of rolling contact fatigue (RCF) of medium carbon bainitic back-up roll steel was investigated under its actual work conditions. A kind of asperity-scale surface originated cracks, which is lying parallel or at an acute angle to the surfaces, initiated after unidirectional plastic flow of the material in thin surface layer had occurred. Theoretical analysis indicates that they nucleate due to plastic ratcheting induced by asperity contact stresses, and consequently are named as ratcheting cracks. After nucleating and initially propagating, they arrest at some depth and resume propagating till about 70%-80% of the RCF failure life by initially turning parallel to contact surfaces. Their behavior of initiation and propagation is confined to a thin layer prior to the formation of surface distress. According to the critical principle of the preventive grinding strategy, removing the asperity influenced surface layer at about 70%-80% of the RCF failure life can effectively prevent the ratcheting cracks from developing into surface distress, which can lead to the formation of macro-RCF failure soon.展开更多
This paper proposes a novel unified visco-plastic constitutive model for uniaxial ratcheting behaviors. The cyclic deformation of the material presents remarkable time-dependence and history memory phenomena. The frac...This paper proposes a novel unified visco-plastic constitutive model for uniaxial ratcheting behaviors. The cyclic deformation of the material presents remarkable time-dependence and history memory phenomena. The fractional(fractional-order)derivative is an efficient tool for modeling these phenomena. Therefore, we develop a cyclic fractional-order unified visco-plastic(FVP) constitutive model. Specifically, within the framework of the cyclic elasto-plastic theory, the fractional derivative is used to describe the accumulated plastic strain rate and nonlinear kinematic hardening rule based on the Ohno-Abdel-Karim model. Moreover, a new radial return method for the back stress is developed to describe the unclosed hysteresis loops of the stress-strain properly.The capacity of the FVP model used to predict the cyclic deformation of the SS304 stainless steel is verified through a comparison with the corresponding experimental data found in the literature(KANG, G. Z., KAN, Q. H., ZHANG, J., and SUN, Y. F. Timedependent ratcheting experiments of SS304 stainless steel. International Journal of Plasticity, 22(5), 858–894(2006)). The FVP model is shown to be successful in predicting the rate-dependent ratcheting behaviors of the SS304 stainless steel.展开更多
An experimental study was carried out on the strain cyclic characteristics and ratcheting of U71Mn rail steel subjected to non-proportional multiaxial cyclic loading. The strain cyclic characteristics were researched ...An experimental study was carried out on the strain cyclic characteristics and ratcheting of U71Mn rail steel subjected to non-proportional multiaxial cyclic loading. The strain cyclic characteristics were researched under the strain-controlled circular load path. The ratcheting was investigated for the stress-controlled multiaxial circular, elliptical and rhombic load paths with different mean stresses, stress amplitudes and their histories. The experiment shows that U71Mn rail steel features the cyclic non-hardening/softening, and its strain cyclic characteristics depend greatly on the strain amplitude but slightly on its history. However, the ratcheting of U71Mn rail steel depends greatly not only on the values of mean stress and stress amplitude, but also on their histories. In the meantime, the shape of load path and its history also apparently influence the ratcheting. The ratcheting changes with the different loading paths.展开更多
In order to investigate the ratcheting behavior of T225NG alloy, a series of ratcheting tests under uniaxial long-cyclic stressing were performed. The results show that the ratcheting strain of this alloy can get into...In order to investigate the ratcheting behavior of T225NG alloy, a series of ratcheting tests under uniaxial long-cyclic stressing were performed. The results show that the ratcheting strain of this alloy can get into shakedown after tens （or hundreds） of thousand cycles. After the ratcheting strain is saturated under the condition that stress amplitude is half of peak stress, it will bring about subsequent fatigue failure, and relationship between fatigue life and one of peak stress and saturated ratcheting （SR） strain meets power law. As the alloy is under stress jiggling with stress amplitude that is 1%-2.5% of peak stress, the ratcheting strain still become remarkable and goes into shakedown after several hundreds of thousand cycles but there exists little accessional strain caused by creep effect. It is notable that, when the peak stress is 85%-100% of yield stress, the long-cyclic stressing will lead SR strain to be from 1.4% to 2.5% even if the initial ratio of ratcheting strain is zero. Based on ratcheting threshold property of peak stress and monotonicity of relationship between the peak stress and SR strain, a saturated ratcheting model （SRM） is developed to predict SR strain and to estimate saturated creep strain also. In addition, the classes of ratcheting evolutions of metals are discussed.展开更多
The accumulation of inelastic deformation occurring in NiTi shape memory alloy under the stress-controlled cyclic loading condition is named transformation ratcheting, since it is mainly caused by the solid-solid tran...The accumulation of inelastic deformation occurring in NiTi shape memory alloy under the stress-controlled cyclic loading condition is named transformation ratcheting, since it is mainly caused by the solid-solid transformation from austenite to martensite phase and vice versa. The transformation ratcheting and its effect on the fatigue life （i.e., transformation-fatigue interaction） are key issues that should be addressed in order to assess the fatigue of NiTi shape memory alloy more accurately. In this paper, the advances in the studies on the transformation ratcheting and rateheting-fatigue interaction of super-elastic NiTi shape memory alloy in recent years are reviewed： First, experimental observation of the uniaxial transformation ratcheting and ratcheting-fatigue interaction of super-elastic NiTi alloy under the stress-controlled cyclic loading conditions is treated, and the detrimental effect of transformation ratcheting on the fatigue life is addressed; Secondly, two types of cyclic constitutive models （i.e., a macroscopic phenomeno- logical model and a micromechanical one based on crystal plasticity） constructed to describe the transformation ratcheting of super-elastic NiTi alloy are discussed; Furthermore, an energy-based failure model is provided and dealt with by comparing its predicted fatigue lives with experimental ones; Finally, some suggestions about future work are made.展开更多
Based on the experimental results of the ratcheting for SS304 stainless steel, a new visco-plastic cyclic constitutive model was established to describe the uniaxial and multiaxial ratcheting of the material at room a...Based on the experimental results of the ratcheting for SS304 stainless steel, a new visco-plastic cyclic constitutive model was established to describe the uniaxial and multiaxial ratcheting of the material at room and elevated temperatures within the framework of unified visco-plasticity. In the model, the temperature dependence of the ratcheting was emphasized, and the dynamic strain aging occurred in the temperature range of 4 00-600℃ for the material was taken into account particularly. Finally, the prediction capability of the developed model was checked by comparing to the corresponding experimental results.展开更多
The uniaxial time-dependent strain cyclic behaviors and ratcheting of SS304 stainless steel were studied at high temperatures （350 ℃ and 700 ℃）. The effects of straining and stressing rates, holding time at the pe...The uniaxial time-dependent strain cyclic behaviors and ratcheting of SS304 stainless steel were studied at high temperatures （350 ℃ and 700 ℃）. The effects of straining and stressing rates, holding time at the peak and/or valley of each cycle in addition to ambient temperature on the cyclic softening/hardening behavior and ratcheting of the material were discussed. It can be seen from experimental results that the material presents remarkable time dependence at 700 ℃, and the ratcheting strain depends greatly on the stressing rate, holding time and ambient temperature. Some significant conclusions are obtained, which are useful to build a constitutive model describiog the time-dependent cyclic deformation of the material.展开更多
Uniaxial ratcheting behaviour and low cycle fatigue(LCF)failure mechanism of nickel-based single crystal superalloy DD6 with[001]orientation are investigated through the stresscontrolled LCF tests with stress ratio of...Uniaxial ratcheting behaviour and low cycle fatigue(LCF)failure mechanism of nickel-based single crystal superalloy DD6 with[001]orientation are investigated through the stresscontrolled LCF tests with stress ratio of-1.Then the deformation behaviour during the wholelifetime from the beginning of the experiment to the fracture of the specimen,as well as the fractographic/metallographic morphology,are compared with the strain-controlled LCF experimental results.Through the scanning electron microscope(SEM)observations,it is shown that the failure characteristics under stress-controlled LCF loading are similar with those under strain-controlled loading.Nevertheless,unlike strain-controlled LCF loading,even under fully reversed cycle loading for stress-controlled LCF,DD6 shows significant ratcheting behaviour due to the tensioncompression asymmetry.In addition,the LCF lifetimes under stress control are significantly shorter than the LCF lifetimes under strain control,and the culprit might be the detrimental effect of ratcheting strain on LCF lifetime.Based on these phenomena,an improved crystal plasticity constitutive model on the basis of slip-based Walker constitutive model is developed through modifying the kinematic hardening rule in order to overcome the inaccurate prediction of decelerating stageand stable stage of ratcheting behaviour.Furthermore,combining the continuum damage mechanics,a damage-coupled crystal plasticity constitutive model is proposed to reflect the damage behaviour of DD6 and the accelerating stage of ratcheting behaviour.The simulation results for the stress-controlled LCF deformation behaviour including the whole-lifetime ratcheting behaviour show good agreement with the experimental data.展开更多
An experimental study was carried out of the cyclic behavior of U71Mn rail steel subjected to uniaxial strain and stress. The effects of cyclic struin amplitude, mean struin,strain loading rate and their histories on ...An experimental study was carried out of the cyclic behavior of U71Mn rail steel subjected to uniaxial strain and stress. The effects of cyclic struin amplitude, mean struin,strain loading rate and their histories on the strain cyclic characteristics were studied.Under the asymmetrical stress cycling, the effects of stress amplitude, mean stress,stress loading rate and their histories on the ratcheting were analyzed. The interaction between strain cycling and stress cycling was also discussed. It is shown that either the cyclic characteristics under strain cycling or the ratcheting under asymmetrical stress cycling depends not only on the cumnt loading state, but also on the previous loading history. Some significant results are obtained.展开更多
The uniaxial ratcheting behavior of a polyetherimide (PEI) polymer 'TECAPEI' was studied using stress-controlled cyclic loading at room temperature, including both cyclic tension-compression with non-zero tens...The uniaxial ratcheting behavior of a polyetherimide (PEI) polymer 'TECAPEI' was studied using stress-controlled cyclic loading at room temperature, including both cyclic tension-compression with non-zero tensile mean stress and tension- unloading tests. The experimental observations were focused on the time-dependent ratcheting of the PEI polymer revealed in cyclic tests at diverse stress rates and with different peak stress holding times. The results showed that the PEI polymer shows obvious ratcheting deformation; i.e., the ratcheting strain accumulates progressively in the tensile direction during stress- controlled cyclic tests with non-zero mean stress. The ratcheting is highly dependent on the applied mean stress and stress am-plitude, and is also characterized by a strong time-dependency during the cyclic stressing at diverse stress rates and with different peak stress holding times. The time-dependent ratcheting of the PEI polymer is caused mainly by its remarkable viscosity. A comparison of the ratcheting occurring before and beyond the ultimate stress point of the PEI polymer showed that the ratcheting beyond the ultimate stress point is more significant than that occurring before that point.展开更多
A series of monotonic uniaxial tensile tests, strain-controlled and stress-controlled cyclic tests of SA508-3 steel were conducted from 25 to 350℃. Results showed that the steel exhibited temperature-dependent cyclic...A series of monotonic uniaxial tensile tests, strain-controlled and stress-controlled cyclic tests of SA508-3 steel were conducted from 25 to 350℃. Results showed that the steel exhibited temperature-dependent cyclic softening characteristic and obvious ratcheting behavior, and dynamic strain aging was observed in the range of 250-350℃. Based on experimental observations, a temperature-dependent cyclic plastic constitutive model was proposed by introducing the nonlinear cyclic softening and kinematic hardening rules, and the dynamic strain aging was also considered into the constitutive model. Comparisons between experiments and simulations were carded out to validate the proposed model at elevated temperature.展开更多
To quickly predict the fatigue limit of 6061 aluminum alloy,two assessment methods based on the temperature evolution and the steady ratcheting strain difference under cyclic loading,respectively,were proposed.The tem...To quickly predict the fatigue limit of 6061 aluminum alloy,two assessment methods based on the temperature evolution and the steady ratcheting strain difference under cyclic loading,respectively,were proposed.The temperature evolutions during static and cyclic loadings were both measured by infrared thermography.Fatigue tests show that the temperature evolution was closely related to the cyclic loading,and the cyclic loading range can be divided into three sections according to the regular of temperature evolution in different section.The mechanism of temperature evolution under different cyclic loadings was also analyzed due to the thermoelastic,viscous,and thermoplastic effects.Additionally,ratcheting strain under cyclic loading was also measured,and the results show that the evolution of the ratcheting strain under cyclic loading above the fatigue limit undergone three stages:the first increasing stage,the second steady state,and the final abrupt increase stage.The fatigue limit of the 6061 aluminum alloy was quickly estimated based on transition point of linear fitting of temperature increase and the steady value of ratcheting strain difference.Besides,it is feasible and quick of the two methods by the proof of the traditional S-N curve.展开更多
An experimental study was carried out on the strain cyclic characteristics and ratcheting of 316L stainless steel subjected to uniaxial and multiaxial cyclic loading. The strain cyclic characteristics were researched ...An experimental study was carried out on the strain cyclic characteristics and ratcheting of 316L stainless steel subjected to uniaxial and multiaxial cyclic loading. The strain cyclic characteristics were researched under the strain-controlled uniaxial tension-compression and multiaxial circular paths of loading. The ratcheting tests were conducted for the stress-controlled uniaxial tension-compression and multiaxial circular, rhombic and linear paths of loading with different mean stresses, stress amplitudes and histories. The experiment results show that 316L stainless steel features the cyclic hardening, and its strain cyclic characteristics depend on the strain amplitude and its history apparently. The ratcheting of 316L stainless steel depends greatly on the Values of mean stress, stress amplitude and their histories. In the meantime, the shape of load path and its history also apparently influence the ratcheting.展开更多
Because of the size limitation of weld joints in different regions, the traditional standard bar specimen is not suitable to investigate the mechanical properties of weld joints. In this study, miniature specimens wer...Because of the size limitation of weld joints in different regions, the traditional standard bar specimen is not suitable to investigate the mechanical properties of weld joints. In this study, miniature specimens were extracted from specific regions(base metal, weld metal, and three heat-affected zones) of API X80 and X70 weld joints. Uniaxial tensile tests were conducted to obtain the mechanical properties of different regions, and then uniaxial ratcheting tests were conducted to investigate the ratcheting behaviors of the different regions under the same peak and nominal stresses. Under both the tensile tests and ratcheting tests, the weld joints exhibit heterogeneous results, such as different mechanical properties and ratcheting behaviors, which were region dependent. Furthermore, the yield strength and yield-to-tensile strength ratio contribute differently to the ratcheting response.展开更多
An objective of this work is to develop a validated computational model that can be used to estimate ratcheting accumulation behavior of granular soils due to high-cyclic loading. An accumulation model was proposed to...An objective of this work is to develop a validated computational model that can be used to estimate ratcheting accumulation behavior of granular soils due to high-cyclic loading. An accumulation model was proposed to describe only the envelope of the maximum plastic deformations generated during the cyclic loading process, which can calculate the accumulated deformation by means of relatively large load cycle increments. The concept of volumetric hardening was incorporated into the model and a so-called overstress formulation was employed to describe the evolution of the accumulated volumetric deformation as a state parameter. The model accounted for ratcheting shakedown and accumulation such as a pseudo-yield surface(a shakedown surface) associated with loading inside the current virgin yield surface which was implemented into the well-known modified Cam-clay model. Finally, the model was calibrated using data from the stress-controlled drained cyclic triaxial tests on homogeneous fine grained sands. It is seen that the model can successfully represent important features of the ratcheting accumulation of both volumetric and deviatoric deformation caused by repeated drained loading over a large number of cycles.展开更多
The uniaxial ratcheting behaviors of several metals with different crystal structures or values of fault energy were observed by the stress-controlled cyclic tests at room temperature. The prescribed metals included 3...The uniaxial ratcheting behaviors of several metals with different crystal structures or values of fault energy were observed by the stress-controlled cyclic tests at room temperature. The prescribed metals included 316L stainless steel, pure copper, pure aluminum, and ordinary 20# carbon steel. The effects of applied mean stress, stress amplitude and stress ratio on the uniaxial ratcheting were also investigated. The observations show that different crystal structures or values of fault energy result in more or less different ratcheting behaviors for the prescribed metals. The different ratcheting behaviors are partially caused by the variation of dislocation mobility.展开更多
The ratcheting response of 316 stainless steel samples at the vicinity of notch roots under single-and multi-step loading conditions is evaluated.Multi-step tests were conducted to examine local ratcheting at differen...The ratcheting response of 316 stainless steel samples at the vicinity of notch roots under single-and multi-step loading conditions is evaluated.Multi-step tests were conducted to examine local ratcheting at different low–high–high and high–low–low loading sequences.The stress levels over loading steps and their sequences highly influenced ratcheting magnitude and rate.The change of stress level from low to high promoted ratcheting over proceeding cycles while ratcheting strains dropped in magnitude for opposing sequence where stress level dropped from high to low.Local ratcheting strain values at the vicinity of notch root were found noticeably larger than nominal ratcheting values measured at farer distances from notch edge through use of strain gauges.Ratcheting values in both mediums of local and nominal were promoted as notch diameter increased.To assess progressive ratcheting response and stress relaxation concurrently,the Ahmadzadeh-Varvani(A-V)kinematic hardening rule was coupled with Neuber’s rule enabling to calculate local stress at notch root of steel samples.Local stress/strain values were progressed at notch root over applied asymmetric stress cycles resulting in ratcheting buildup through A-V model.The relaxation of stress values at a given peak-valley strain event was governed through the Neuber’s rule.Experimental ratcheting data were found agreeable with those predicted through the coupled framework.展开更多
A series of fully reversed axial, torsional strain-controlled cyclic tests and two multiaxial ratcheting tests were conducted on weld metal specimens using an Instron8521 tension-torsional servo-controlled testing mac...A series of fully reversed axial, torsional strain-controlled cyclic tests and two multiaxial ratcheting tests were conducted on weld metal specimens using an Instron8521 tension-torsional servo-controlled testing machine. The weld metal showed clear cyclic softening under axial, torsional and multiaxial loading. A modified kinematic hardening rule was proposed in which a multiaxial-loading-dependent parameter incorporated the radial evanescence term of the Burlet-Cailletaud mode with the Ohno-Wang kinematic hardening rule to predict the multiaxial ratcheting effects. The introduction of yield stress evolved with accumulated plasticity strain enables the model to predict cyclic plasticity behavior of cyclic softening or cyclic hardening materials. Thus modified model considers the isotropic hardening as well as kinematic hardening of yield surface, and it can present description of plasticity behavior and ratcheting of cyclic softening and cyclic hardening materials well under multiaxial loading.展开更多
In this paper, cyclic loading behavior of carbon steel pressurized piping elbows are described. Effects of internal pressure and bending moment amplitude on the ratcheting rate are investigated. The AF kinematic harde...In this paper, cyclic loading behavior of carbon steel pressurized piping elbows are described. Effects of internal pressure and bending moment amplitude on the ratcheting rate are investigated. The AF kinematic hardening model is used to predict the plastic behavior of the elbows. Material parameters and stress-strain data have been obtained from several stabilized cycles of specimens that are subjected to symmetric strain cycles. The results show that the maximum ratcheting strain occurred mainly in the hoop direction at flanks. Hoop strain ratcheting was found at intrados for individual specimen. Ratcheting strain rate increases with increase of the bending loading level at the constant internal pressure. The results show that the initial rate of ratcheting is large and then it decreases with the increasing cycles. The FE model predicts the hoop strain ratcheting rate to be near that found experimentally in all cases that M/Ml≤1..展开更多
基金Financial supports from the National Natural Science Foundation of China NSFC(No.12322203,12072296)are greatly appreciated.
文摘This paper investigates the effect of hydrogen on the transformation ratcheting of NiTi shape memory alloy(SMA)wires in the experimental and theoretical aspects.In the aspect of experiments,the NiTi SMA orthodontic wires are hydrogen charged by the electrochemical charging method at room temperature with varying charging durations and charging lengths.After that,the ex-situ cyclic tension-unloading experiments are performed for the charged and non-charged wires.Experimental results reveal that the two transformation platforms(two-step MT)occur during the forward MT at the beginning and end of cyclic deformation for hydrogen-charged wires,which can be regarded as a global response of the non-charged and charged regions.Furthermore,this two-step MT and transformation ratcheting aggravate with the increase of the charging duration.In the aspect of the theoretical model,a diffusional-mechanically coupled constitutive model is developed.In this constitutive model,the strain is considered as four components:elasticity,transformation(MT),hydrogen expansion and transformation-induced plasticity(TRIP).Combining Helmholtz free energy and Clausius–Duhem inequality,the thermodynamic driving forces of MT and TRIP are obtained.Fick’s law and the mass conservation equation are incorporated to derive the evolution of hydrogen concentration.A transition from material points to the whole wire is employed to extend the model from a material point to the entire wire,and the overall response with a heterogeneous hydrogen concentration field is obtained.The proposed model's ability to predict the transformation ratcheting of the non-charged and charged NiTi SMA wires is verified by contrasting predictions and experimental results.
文摘The behavior of rolling contact fatigue (RCF) of medium carbon bainitic back-up roll steel was investigated under its actual work conditions. A kind of asperity-scale surface originated cracks, which is lying parallel or at an acute angle to the surfaces, initiated after unidirectional plastic flow of the material in thin surface layer had occurred. Theoretical analysis indicates that they nucleate due to plastic ratcheting induced by asperity contact stresses, and consequently are named as ratcheting cracks. After nucleating and initially propagating, they arrest at some depth and resume propagating till about 70%-80% of the RCF failure life by initially turning parallel to contact surfaces. Their behavior of initiation and propagation is confined to a thin layer prior to the formation of surface distress. According to the critical principle of the preventive grinding strategy, removing the asperity influenced surface layer at about 70%-80% of the RCF failure life can effectively prevent the ratcheting cracks from developing into surface distress, which can lead to the formation of macro-RCF failure soon.
基金Project supported by the National Natural Science Foundation of China(Nos.11790282,U1534204,and 11472179)the Natural Science Foundation of Hebei Province of China(No.A2016210099)
文摘This paper proposes a novel unified visco-plastic constitutive model for uniaxial ratcheting behaviors. The cyclic deformation of the material presents remarkable time-dependence and history memory phenomena. The fractional(fractional-order)derivative is an efficient tool for modeling these phenomena. Therefore, we develop a cyclic fractional-order unified visco-plastic(FVP) constitutive model. Specifically, within the framework of the cyclic elasto-plastic theory, the fractional derivative is used to describe the accumulated plastic strain rate and nonlinear kinematic hardening rule based on the Ohno-Abdel-Karim model. Moreover, a new radial return method for the back stress is developed to describe the unclosed hysteresis loops of the stress-strain properly.The capacity of the FVP model used to predict the cyclic deformation of the SS304 stainless steel is verified through a comparison with the corresponding experimental data found in the literature(KANG, G. Z., KAN, Q. H., ZHANG, J., and SUN, Y. F. Timedependent ratcheting experiments of SS304 stainless steel. International Journal of Plasticity, 22(5), 858–894(2006)). The FVP model is shown to be successful in predicting the rate-dependent ratcheting behaviors of the SS304 stainless steel.
基金Financially supported by the National Natural Science Foundation of China(197T2041)the Excellent Youth Fund of Sichuan Province.
文摘An experimental study was carried out on the strain cyclic characteristics and ratcheting of U71Mn rail steel subjected to non-proportional multiaxial cyclic loading. The strain cyclic characteristics were researched under the strain-controlled circular load path. The ratcheting was investigated for the stress-controlled multiaxial circular, elliptical and rhombic load paths with different mean stresses, stress amplitudes and their histories. The experiment shows that U71Mn rail steel features the cyclic non-hardening/softening, and its strain cyclic characteristics depend greatly on the strain amplitude but slightly on its history. However, the ratcheting of U71Mn rail steel depends greatly not only on the values of mean stress and stress amplitude, but also on their histories. In the meantime, the shape of load path and its history also apparently influence the ratcheting. The ratcheting changes with the different loading paths.
文摘In order to investigate the ratcheting behavior of T225NG alloy, a series of ratcheting tests under uniaxial long-cyclic stressing were performed. The results show that the ratcheting strain of this alloy can get into shakedown after tens （or hundreds） of thousand cycles. After the ratcheting strain is saturated under the condition that stress amplitude is half of peak stress, it will bring about subsequent fatigue failure, and relationship between fatigue life and one of peak stress and saturated ratcheting （SR） strain meets power law. As the alloy is under stress jiggling with stress amplitude that is 1%-2.5% of peak stress, the ratcheting strain still become remarkable and goes into shakedown after several hundreds of thousand cycles but there exists little accessional strain caused by creep effect. It is notable that, when the peak stress is 85%-100% of yield stress, the long-cyclic stressing will lead SR strain to be from 1.4% to 2.5% even if the initial ratio of ratcheting strain is zero. Based on ratcheting threshold property of peak stress and monotonicity of relationship between the peak stress and SR strain, a saturated ratcheting model （SRM） is developed to predict SR strain and to estimate saturated creep strain also. In addition, the classes of ratcheting evolutions of metals are discussed.
基金Project supported by the National Natural Science Foundation of China (No. 11025210)Sichuan Provincial Youth Science and Technology Innovation Team, China (2013)
文摘The accumulation of inelastic deformation occurring in NiTi shape memory alloy under the stress-controlled cyclic loading condition is named transformation ratcheting, since it is mainly caused by the solid-solid transformation from austenite to martensite phase and vice versa. The transformation ratcheting and its effect on the fatigue life （i.e., transformation-fatigue interaction） are key issues that should be addressed in order to assess the fatigue of NiTi shape memory alloy more accurately. In this paper, the advances in the studies on the transformation ratcheting and rateheting-fatigue interaction of super-elastic NiTi shape memory alloy in recent years are reviewed： First, experimental observation of the uniaxial transformation ratcheting and ratcheting-fatigue interaction of super-elastic NiTi alloy under the stress-controlled cyclic loading conditions is treated, and the detrimental effect of transformation ratcheting on the fatigue life is addressed; Secondly, two types of cyclic constitutive models （i.e., a macroscopic phenomeno- logical model and a micromechanical one based on crystal plasticity） constructed to describe the transformation ratcheting of super-elastic NiTi alloy are discussed; Furthermore, an energy-based failure model is provided and dealt with by comparing its predicted fatigue lives with experimental ones; Finally, some suggestions about future work are made.
基金supported by the Theoretical Research Fund of Sichuan Province(No.03JY029-062-2)the Scientific Research Foundation for the Returned Overseas Chinese Scholars(SRF-ROCS),State Education Ministry of China(No.2003-406-01).
文摘Based on the experimental results of the ratcheting for SS304 stainless steel, a new visco-plastic cyclic constitutive model was established to describe the uniaxial and multiaxial ratcheting of the material at room and elevated temperatures within the framework of unified visco-plasticity. In the model, the temperature dependence of the ratcheting was emphasized, and the dynamic strain aging occurred in the temperature range of 4 00-600℃ for the material was taken into account particularly. Finally, the prediction capability of the developed model was checked by comparing to the corresponding experimental results.
基金Item Sponsored by National Natural Science Foundation of China (NSFC10402037) Theoretical Research Fund of SouthwestJiaotong University (2005XJB23)
文摘The uniaxial time-dependent strain cyclic behaviors and ratcheting of SS304 stainless steel were studied at high temperatures （350 ℃ and 700 ℃）. The effects of straining and stressing rates, holding time at the peak and/or valley of each cycle in addition to ambient temperature on the cyclic softening/hardening behavior and ratcheting of the material were discussed. It can be seen from experimental results that the material presents remarkable time dependence at 700 ℃, and the ratcheting strain depends greatly on the stressing rate, holding time and ambient temperature. Some significant conclusions are obtained, which are useful to build a constitutive model describiog the time-dependent cyclic deformation of the material.
基金financial support from National Natural Science Foundation of China(Nos.51875020,51675024 and 51811540406)National Science and Technology Major Project(No.2017-IV-0004-0041)+1 种基金Aviation Science Foundation of China(No.6141B090314)Academic Excellence Foundation of BUAA。
文摘Uniaxial ratcheting behaviour and low cycle fatigue(LCF)failure mechanism of nickel-based single crystal superalloy DD6 with[001]orientation are investigated through the stresscontrolled LCF tests with stress ratio of-1.Then the deformation behaviour during the wholelifetime from the beginning of the experiment to the fracture of the specimen,as well as the fractographic/metallographic morphology,are compared with the strain-controlled LCF experimental results.Through the scanning electron microscope(SEM)observations,it is shown that the failure characteristics under stress-controlled LCF loading are similar with those under strain-controlled loading.Nevertheless,unlike strain-controlled LCF loading,even under fully reversed cycle loading for stress-controlled LCF,DD6 shows significant ratcheting behaviour due to the tensioncompression asymmetry.In addition,the LCF lifetimes under stress control are significantly shorter than the LCF lifetimes under strain control,and the culprit might be the detrimental effect of ratcheting strain on LCF lifetime.Based on these phenomena,an improved crystal plasticity constitutive model on the basis of slip-based Walker constitutive model is developed through modifying the kinematic hardening rule in order to overcome the inaccurate prediction of decelerating stageand stable stage of ratcheting behaviour.Furthermore,combining the continuum damage mechanics,a damage-coupled crystal plasticity constitutive model is proposed to reflect the damage behaviour of DD6 and the accelerating stage of ratcheting behaviour.The simulation results for the stress-controlled LCF deformation behaviour including the whole-lifetime ratcheting behaviour show good agreement with the experimental data.
文摘An experimental study was carried out of the cyclic behavior of U71Mn rail steel subjected to uniaxial strain and stress. The effects of cyclic struin amplitude, mean struin,strain loading rate and their histories on the strain cyclic characteristics were studied.Under the asymmetrical stress cycling, the effects of stress amplitude, mean stress,stress loading rate and their histories on the ratcheting were analyzed. The interaction between strain cycling and stress cycling was also discussed. It is shown that either the cyclic characteristics under strain cycling or the ratcheting under asymmetrical stress cycling depends not only on the cumnt loading state, but also on the previous loading history. Some significant results are obtained.
基金Project (No 2008TPL_Z03) supported by the Key Open Foundation of State Key Laboratory of Traction Power, China
文摘The uniaxial ratcheting behavior of a polyetherimide (PEI) polymer 'TECAPEI' was studied using stress-controlled cyclic loading at room temperature, including both cyclic tension-compression with non-zero tensile mean stress and tension- unloading tests. The experimental observations were focused on the time-dependent ratcheting of the PEI polymer revealed in cyclic tests at diverse stress rates and with different peak stress holding times. The results showed that the PEI polymer shows obvious ratcheting deformation; i.e., the ratcheting strain accumulates progressively in the tensile direction during stress- controlled cyclic tests with non-zero mean stress. The ratcheting is highly dependent on the applied mean stress and stress am-plitude, and is also characterized by a strong time-dependency during the cyclic stressing at diverse stress rates and with different peak stress holding times. The time-dependent ratcheting of the PEI polymer is caused mainly by its remarkable viscosity. A comparison of the ratcheting occurring before and beyond the ultimate stress point of the PEI polymer showed that the ratcheting beyond the ultimate stress point is more significant than that occurring before that point.
基金Financial supports by the National Natural Science Foundation of China (No. 11572265)the distinguished Young Scholars of Sichuan (No. 2017JQ0019)the Science and Technology on Reactor System Design Technology Laboratory of China are appreciated
文摘A series of monotonic uniaxial tensile tests, strain-controlled and stress-controlled cyclic tests of SA508-3 steel were conducted from 25 to 350℃. Results showed that the steel exhibited temperature-dependent cyclic softening characteristic and obvious ratcheting behavior, and dynamic strain aging was observed in the range of 250-350℃. Based on experimental observations, a temperature-dependent cyclic plastic constitutive model was proposed by introducing the nonlinear cyclic softening and kinematic hardening rules, and the dynamic strain aging was also considered into the constitutive model. Comparisons between experiments and simulations were carded out to validate the proposed model at elevated temperature.
基金This work was financially supported by the National Natural Science Foundation of China(Nos.51505322 and 51775366)the Natural Science Foundation of Shanxi Province,China(No.201801D221137).
文摘To quickly predict the fatigue limit of 6061 aluminum alloy,two assessment methods based on the temperature evolution and the steady ratcheting strain difference under cyclic loading,respectively,were proposed.The temperature evolutions during static and cyclic loadings were both measured by infrared thermography.Fatigue tests show that the temperature evolution was closely related to the cyclic loading,and the cyclic loading range can be divided into three sections according to the regular of temperature evolution in different section.The mechanism of temperature evolution under different cyclic loadings was also analyzed due to the thermoelastic,viscous,and thermoplastic effects.Additionally,ratcheting strain under cyclic loading was also measured,and the results show that the evolution of the ratcheting strain under cyclic loading above the fatigue limit undergone three stages:the first increasing stage,the second steady state,and the final abrupt increase stage.The fatigue limit of the 6061 aluminum alloy was quickly estimated based on transition point of linear fitting of temperature increase and the steady value of ratcheting strain difference.Besides,it is feasible and quick of the two methods by the proof of the traditional S-N curve.
文摘An experimental study was carried out on the strain cyclic characteristics and ratcheting of 316L stainless steel subjected to uniaxial and multiaxial cyclic loading. The strain cyclic characteristics were researched under the strain-controlled uniaxial tension-compression and multiaxial circular paths of loading. The ratcheting tests were conducted for the stress-controlled uniaxial tension-compression and multiaxial circular, rhombic and linear paths of loading with different mean stresses, stress amplitudes and histories. The experiment results show that 316L stainless steel features the cyclic hardening, and its strain cyclic characteristics depend on the strain amplitude and its history apparently. The ratcheting of 316L stainless steel depends greatly on the Values of mean stress, stress amplitude and their histories. In the meantime, the shape of load path and its history also apparently influence the ratcheting.
基金supported by the National Natural Science Foundation of China (No. 51435012)
文摘Because of the size limitation of weld joints in different regions, the traditional standard bar specimen is not suitable to investigate the mechanical properties of weld joints. In this study, miniature specimens were extracted from specific regions(base metal, weld metal, and three heat-affected zones) of API X80 and X70 weld joints. Uniaxial tensile tests were conducted to obtain the mechanical properties of different regions, and then uniaxial ratcheting tests were conducted to investigate the ratcheting behaviors of the different regions under the same peak and nominal stresses. Under both the tensile tests and ratcheting tests, the weld joints exhibit heterogeneous results, such as different mechanical properties and ratcheting behaviors, which were region dependent. Furthermore, the yield strength and yield-to-tensile strength ratio contribute differently to the ratcheting response.
基金Projects(41302219,41302076)supported by the National Natural Science Foundation of China
文摘An objective of this work is to develop a validated computational model that can be used to estimate ratcheting accumulation behavior of granular soils due to high-cyclic loading. An accumulation model was proposed to describe only the envelope of the maximum plastic deformations generated during the cyclic loading process, which can calculate the accumulated deformation by means of relatively large load cycle increments. The concept of volumetric hardening was incorporated into the model and a so-called overstress formulation was employed to describe the evolution of the accumulated volumetric deformation as a state parameter. The model accounted for ratcheting shakedown and accumulation such as a pseudo-yield surface(a shakedown surface) associated with loading inside the current virgin yield surface which was implemented into the well-known modified Cam-clay model. Finally, the model was calibrated using data from the stress-controlled drained cyclic triaxial tests on homogeneous fine grained sands. It is seen that the model can successfully represent important features of the ratcheting accumulation of both volumetric and deviatoric deformation caused by repeated drained loading over a large number of cycles.
基金support of the National Natural Science Foundation of China (Grant No. 10772153)
文摘The uniaxial ratcheting behaviors of several metals with different crystal structures or values of fault energy were observed by the stress-controlled cyclic tests at room temperature. The prescribed metals included 316L stainless steel, pure copper, pure aluminum, and ordinary 20# carbon steel. The effects of applied mean stress, stress amplitude and stress ratio on the uniaxial ratcheting were also investigated. The observations show that different crystal structures or values of fault energy result in more or less different ratcheting behaviors for the prescribed metals. The different ratcheting behaviors are partially caused by the variation of dislocation mobility.
基金Authors wish to acknowledge the financial support by the Natural Sciences and Engineering Research Council(NSERC)of Canada.
文摘The ratcheting response of 316 stainless steel samples at the vicinity of notch roots under single-and multi-step loading conditions is evaluated.Multi-step tests were conducted to examine local ratcheting at different low–high–high and high–low–low loading sequences.The stress levels over loading steps and their sequences highly influenced ratcheting magnitude and rate.The change of stress level from low to high promoted ratcheting over proceeding cycles while ratcheting strains dropped in magnitude for opposing sequence where stress level dropped from high to low.Local ratcheting strain values at the vicinity of notch root were found noticeably larger than nominal ratcheting values measured at farer distances from notch edge through use of strain gauges.Ratcheting values in both mediums of local and nominal were promoted as notch diameter increased.To assess progressive ratcheting response and stress relaxation concurrently,the Ahmadzadeh-Varvani(A-V)kinematic hardening rule was coupled with Neuber’s rule enabling to calculate local stress at notch root of steel samples.Local stress/strain values were progressed at notch root over applied asymmetric stress cycles resulting in ratcheting buildup through A-V model.The relaxation of stress values at a given peak-valley strain event was governed through the Neuber’s rule.Experimental ratcheting data were found agreeable with those predicted through the coupled framework.
文摘A series of fully reversed axial, torsional strain-controlled cyclic tests and two multiaxial ratcheting tests were conducted on weld metal specimens using an Instron8521 tension-torsional servo-controlled testing machine. The weld metal showed clear cyclic softening under axial, torsional and multiaxial loading. A modified kinematic hardening rule was proposed in which a multiaxial-loading-dependent parameter incorporated the radial evanescence term of the Burlet-Cailletaud mode with the Ohno-Wang kinematic hardening rule to predict the multiaxial ratcheting effects. The introduction of yield stress evolved with accumulated plasticity strain enables the model to predict cyclic plasticity behavior of cyclic softening or cyclic hardening materials. Thus modified model considers the isotropic hardening as well as kinematic hardening of yield surface, and it can present description of plasticity behavior and ratcheting of cyclic softening and cyclic hardening materials well under multiaxial loading.
文摘In this paper, cyclic loading behavior of carbon steel pressurized piping elbows are described. Effects of internal pressure and bending moment amplitude on the ratcheting rate are investigated. The AF kinematic hardening model is used to predict the plastic behavior of the elbows. Material parameters and stress-strain data have been obtained from several stabilized cycles of specimens that are subjected to symmetric strain cycles. The results show that the maximum ratcheting strain occurred mainly in the hoop direction at flanks. Hoop strain ratcheting was found at intrados for individual specimen. Ratcheting strain rate increases with increase of the bending loading level at the constant internal pressure. The results show that the initial rate of ratcheting is large and then it decreases with the increasing cycles. The FE model predicts the hoop strain ratcheting rate to be near that found experimentally in all cases that M/Ml≤1..
