Pure titanium fabricated by powder metallurgy generally encounters problems including low relative density and low strength,which limits its application performance.This work proposed a multi-step pressing(MSP)techniq...Pure titanium fabricated by powder metallurgy generally encounters problems including low relative density and low strength,which limits its application performance.This work proposed a multi-step pressing(MSP)technique for developing highstrength pure titanium.The MSP processes of spherical Ti powders of 15–53μm,53–105μm,and 75–180μm were systematically investigated through multi-particle fnite element method(MPFEM)compared with conventional one-step pressing(OSP)technique.The relative density,phase constitution,microstructure,and compressive mechanical properties of the sintered bulk pure titanium were characterized.Simulation results demonstrate that the MSP technique signifcantly increases the relative density of green compacts by 3.2%,3.3%,and 5.2%,respectively,compared with OSP technique.Experimental results indicate the relative density of the sintered specimens prepared by MSP spherical powders increases by 5.4%,4.5%,and 4.5%,respectively,compared to OSP,and the yield strength improves by 16%,13%,and 18%.For the sintered specimens prepared by MSP irregular powder of 15–53μm,the relative density increases by 6.0%and the yield strength increases by 15%.The enhancement of relative density and yield strength is mainly because the MSP technique mitigates stress concentration between powder particles.Compared to spherical powder,irregular powder exhibits stronger mechanical interlocking owing to the greater propensity for displacement and deformation,which facilitates mutual wedging and interlocking,resulting in superior strength performance.展开更多
The features of additive manufacturing(AM)have made commercially pure titanium(CP-Ti)an attractive candidate material for biomedical implants.However,achieving high strength and ductility is challenging because of the...The features of additive manufacturing(AM)have made commercially pure titanium(CP-Ti)an attractive candidate material for biomedical implants.However,achieving high strength and ductility is challenging because of the columnar structures and fine martensite formation.This study investigated the effect of carbon nanotubes(CNTs)addition on the microstructure and mechanical properties of grade 1 CP-Ti(Gr-1)during the laser powder bed fusion(L-PBF)process.A minute amount of 0.2%mass fraction(wt%)CNTs addition resulted in a high yield strength of approximately 700 MPa and exceptional ductility of 25.7%.Therein,a portion of the CNTs dissolved in the matrix as solute atoms,contributing to solution strengthening,while others were transformed into Ti C_(x)through an in situ reaction with the Ti matrix.Furthermore,the addition of CNTs resulted in the formation of a larger fraction of equiaxed grains and increased the activity of basal and prismatic slip systems.Hence,Gr-1 with CNTs exhibited significantly increased ductility while maintaining a high strength comparable to that of Gr-1 without CNTs.The insights gained from this study provide a novel approach for designing strong and ductile Ti alloys for AM.展开更多
The development of microstructure and texture during cold deep drawing of commercially pure titanium（CP-Ti） was investigated.Three parts,stretching region,drawing region and flange region,were sequentially formed in...The development of microstructure and texture during cold deep drawing of commercially pure titanium（CP-Ti） was investigated.Three parts,stretching region,drawing region and flange region,were sequentially formed in the deep drawing process of the hemispheric surface part,with reference to deformation modes and strain regimes.Results show that the plastic strain is accommodated by dislocation slip and deformation twinning in the whole deep drawing process.The texture of the CP-Ti sheet and its drawn part consists of rolling texture component and recrystallization texture component.The intensity and type of the initial texture varied during the drawing process are related to the production of deformation twinning and dislocation slip.Twinning weakens the initial texture by randomizing the orientations of crystals,especially for the recrystallization texture.The recrystallization texture in the drawing region disappears due to the significant forming of twinning.Furthermore,over drawing would result in the predominance of dislocation slip and the texture is strengthened.展开更多
Titanium with gradient nano-to-micron scale grains from surface to matrix was fabricated by surface mechanical grinding treatment(SMGT) at room temperature.The SMGT-treated titanium shows higher strength than that of ...Titanium with gradient nano-to-micron scale grains from surface to matrix was fabricated by surface mechanical grinding treatment(SMGT) at room temperature.The SMGT-treated titanium shows higher strength than that of as-received one,but moderate ductility between those of ultra-fine grained(UFG) and coarse-grained titanium.Tensile stress-strain curves of SMGT-treated titanium show double strain hardening regimes.The strain hardening rate(dσ/dε) decreases with increasing strain in tensile deformation.The high strain hardening rate at initial yielding is attributed to nano-to-micron-grained surface layer.The low strain hardening rate at large plastic strain regime primarily results from coarse-grained matrix.The SMGT-treated titanium shows a ductile fracture mode with a large number of dimples.The small size of dimples in the treated surface layer is due to the combination of the high strength and strain hardening exponent.The difference between dimple size in nano-to-micron-grained surface layer and coarse-grained matrix is discussed in terms of plastic zone size at the tip of crack in the SMGT-treated titanium.展开更多
In order to reveal the differences caused by forging and rolling process for titanium ingots, hot compression behavior, mechanical properties and the microstructures of forged billets and rolled ones were investigated...In order to reveal the differences caused by forging and rolling process for titanium ingots, hot compression behavior, mechanical properties and the microstructures of forged billets and rolled ones were investigated in detail using Gleeble-1500 thermal mechanical simulator, universal testing machine and optical microscope （OM）. The compression deformation experimental data of commercially pure titanium （CP-Ti） were mapped to be a T vs lg diagram in which data fall into three distinct regions, i.e., three-stage work hardening, two-stage work hardening and flow softening, which can be separated by border lines at 17.5 and 15.4 for lg Z, where Z represents the Zener-Hollomon parameter. The deformation twin is found to have higher Z-value corresponding to the work hardening region. The differences in microstructures and mechanical properties for two kinds of billets indicate that forged billet consists of deformation twins and some twin intersections, and many twins cross the grain boundaries. However, nearly no twins can be seen in the microstructure of billet formed by rolling under optical microscope （OM）, but there are equiaxed and platelike grains. Tensile tests and Vickers hardness test indicate that yield strength, tensile strength and microhardness of the samples after forging are higher than those after rolling.展开更多
TA2 pure titanium was chosen to research the interaction among deformation, recrystallization and phase transformation during hot compression. The samples were hot compressed by thermal simulation method with differen...TA2 pure titanium was chosen to research the interaction among deformation, recrystallization and phase transformation during hot compression. The samples were hot compressed by thermal simulation method with different processing parameters. Variant selection induced by stress during cooling after compression was found. The prismatical texture component which featured that the [0001] direction perpendicular to the compressing direction produced preferentially under the compressing stress. As a result, the transformedα phase possesses strong prismatical texture which is different with the basal texture of compressed αphase. The minimum elastic strain energy is demonstrated to be the main reason that causes the variant selection. Dynamic recrystallization behavior and microstructure evolution during hot compression were also studied.展开更多
The effects of cold rolling and annealing on the microstructure and textural evolution of a commercially pure titanium（CP-Ti） sheet were investigated. Electron backscatter diffractometry demonstrates that the deform...The effects of cold rolling and annealing on the microstructure and textural evolution of a commercially pure titanium（CP-Ti） sheet were investigated. Electron backscatter diffractometry demonstrates that the deformation during rolling is accommodated by twinning and slip. Additionally, twinning is the dominant deformation mechanism when the cold rolling reduction is less than 40%. During rolling, {11ˉ22}11ˉ2ˉ3contraction twinning（CT） and {10ˉ12}10ˉ11 extension twinning（ET） are activated. And, the intensity of the（0002） pole along the ND gradually increases with increasing deformation. During annealing, the fraction of low angle grain boundaries（LAGBs） and the intensity of the（0002） pole along the ND gradually decrease slightly with increasing annealing time, while twinning lamellae disappear rapidly. When the annealing time reaches 60 min, 20% cold-rolled sheet recrystallizes almost completely.展开更多
Key Laboratory for Beam Technology and Materials Modification, Institute ofLow Energy Nuclear Physics, Beijing Normal UniversityThe morphology, composition, and phase structure of the oxide coatings produced on the su...Key Laboratory for Beam Technology and Materials Modification, Institute ofLow Energy Nuclear Physics, Beijing Normal UniversityThe morphology, composition, and phase structure of the oxide coatings produced on the surface ofpure titanium by alternating-current microarc discharge in aluminate solution were investigated byX-ray diffraction and scanning electron microscopy. The profiles of the hardness H and the elasticmodulus E in the coatings were determined using a nanoindentation method. The concentrationdistributions of Ti, Al, and O in the coating show that this coating over 30 mu m thick contains twolayers: an outer layer and an inner layer. The oxide coating is mainly composed of TiO_2 rutile andAl_2TiO_5 compounds. During oxidation, the temperature in the microarc discharge channel was veryhigh to make the local coating molten. From the surface to the interior of the coating, H and Eincrease gradually, and then reach maximum values of 9.78 GPa and 176 GPa respectively at a distanceof 7 mu m from the coating/titanium interface. They are also rather high near the interface.展开更多
Equal channel angular pressing(ECAP)is one of the most effective processes to produce ultra-fine grain(UFG)and nanocrystalline(NC)materials.Because the commercially pure titanium exhibits excellent biocompatibility pr...Equal channel angular pressing(ECAP)is one of the most effective processes to produce ultra-fine grain(UFG)and nanocrystalline(NC)materials.Because the commercially pure titanium exhibits excellent biocompatibility properties,it has a significant potential to be utilized as an implant material.The low static and dynamic strengths of the pure titanium are one of the weaknesses of this material.This defect can be removed by applying the ECAP process on the pure titanium.In this work,the commercially pure titanium Grade2(CP-Ti of Grade2)was pressed at room temperature by the ECAP process via a channel angle of135°for3passes.The microstructural analysis and mechanical tests such as tensile test,hardness test,three-point bending test and Charpy impact test were all carried out on the ECAPed CP-Ti through3passes.The microstructural evolution reveals that by applying the ECAP process,coarse grain(CG)structure develops to UFG/NC structure.Moreover,the results of the mechanical tests show that the process significantly increases the yield and ultimate tensile strengths,bending strength,hardness and fracture toughness of the commercially pure titanium so that it can be used as a replacement for metallic alloys used as biomaterials.展开更多
In order to establish the rolling process parameters of grade-2 commercially pure titanium （CP-Ti）, it is necessary to understand the transformation mechanism and mechanical properties of this material. The β→α t...In order to establish the rolling process parameters of grade-2 commercially pure titanium （CP-Ti）, it is necessary to understand the transformation mechanism and mechanical properties of this material. The β→α transformation kinetics of the grade-2 CP-Ti during continuous cooling was measured and its hot compression behavior was investigated using Gleeble-1500 thermal mechanical simulator. Dynamic CCT diagram confirms that cooling rate has an obvious effect on the start and finishing transformation and microstructures at room temperature. The critical cooling rate for γ-phase transforms to a phase is about 15℃/s. When the cooling rate is higher than 15 ℃/s, some β phases with fine granular shape remain residually into plate-like structure. The plate-like a phase forms at cooling rate lower than 2 ℃/s, serrate a phase forms at medium cooling rates, about 5-15℃/s. The flow stress behavior of grade-2 CP-Ti was investigated in a temperature range of 700-900℃ and strain rate of 3.6-40 mm/min. The results show that dynamic recrystallization, dynamic recovery and work-hardening obviously occur during hot deformation. Constitutive equation of grade-2 CP-Ti was established by analyzing the relationship of the deformation temperature, strain rate, deformation degree and deformation resistance.展开更多
The strength of traditional commercially pure titanium(CP-Ti) alloys often fails to meet the demand of structural materials. In order to enhance their mechanical properties, the cold-rolled CP-Ti alloys were annealed ...The strength of traditional commercially pure titanium(CP-Ti) alloys often fails to meet the demand of structural materials. In order to enhance their mechanical properties, the cold-rolled CP-Ti alloys were annealed at different temperatures, and the recrystallization behavior and texture evolution were investigated. It was found that the bimodal microstructure(equiaxed and elongated grains) was formed after partial recrystallization, and the corresponding sample exhibited an excellent combination of ultimate tensile strength(702 MPa) and total elongation(36.4%). The recrystallization nucleation of CP-Ti sheets occurred preferentially in the high strain and the high-angle grain boundaries(HAGBs) regions. Meanwhile, the internal misorientations of the deformed heterogeneous grains increased and transformed into HAGBs, which further promoted the recrystallization nucleation. The main recrystallization texture was basal TD-split texture transformed from cold-rolled basal RD-split texture, and the oriented nucleation played a dominated role during recrystallization.展开更多
The specimens cut from the cold-rolled pure titanium sheet at 0°,45°and 90°to the rolling direction were treated by high density electropulsing(maximum current density J=(7.22-7.96)×10^(3)A/mm^(2),...The specimens cut from the cold-rolled pure titanium sheet at 0°,45°and 90°to the rolling direction were treated by high density electropulsing(maximum current density J=(7.22-7.96)×10^(3)A/mm^(2),pulse period t_(p)=110μs).The mechanical properties and microstructures of the cold-rolled,electropulsed and conventional annealed commercially pure titanium sheet were examined by using uniaxial tension test machine and optical microscope(OM),respectively.The results show that the deformation behavior of the electropulsed pure titanium sheet is significantly different from that of conventional annealed pure titanium sheet.The difference of the mechanical properties between the 0°,45°and 90°direction specimens is almost diminished.It is mainly due to the increase in dislocation mobility and formation of lamellar microstructure after the electropulsing.展开更多
A review on severe plastic deformation（SPD） technique of equal channel angular pressing（ECAP） process of commercially pure titanium（CP-Ti） alloys was presented with a major emphasize on the influence of ECAP par...A review on severe plastic deformation（SPD） technique of equal channel angular pressing（ECAP） process of commercially pure titanium（CP-Ti） alloys was presented with a major emphasize on the influence of ECAP parameters that include channel and curvature angles, processing route, temperature of operation, pressing speed, internal heating, number of pass through the die and back pressure. Various ECAP characteristics such as microstructure, strain inhomogeneity and mechanical properties are considered to achieve the maximum homogeneity, equilibrium grain refinement and mechanical improvement of CP-Ti. Investigations show that a pressing speed of 1-3 mm/s at 450 °C with route BC along with channel and curvature angles of 90° and 20° respectively with backpressure can lead to the most homogeneous ultrafine microstructure.展开更多
The effects of electropulsing-assisted ultrasonic surface rolling process on surface mechanical properties andmicrostructure evolution of commercial pure titanium were investigated. It was found that the surface mecha...The effects of electropulsing-assisted ultrasonic surface rolling process on surface mechanical properties andmicrostructure evolution of commercial pure titanium were investigated. It was found that the surface mechanical prop-erties were significantly enhanced compared to traditional ultrasonic surface rolling process （USRP）, leading to smallersurface roughness and smoother morphology with fewer cracks and defects. Moreover, surface strengthened layer wasremarkably enhanced with deeper severe plastic deformation layer and higher surface hardness. Remarkable enhancementsof surface mechanical properties may be related to the gradient refined microstructure, the enhanced severe plasticdeformation layer and the accelerated formation of sub-boundaries and twins induced by coupling effects of USRP andelectropulsing. The primary intrinsic reasons for these improvements may be attributed to the thermal and athermal effectscaused by electropulsing treatment, which would accelerate dislocation mobility and atom diffusion.展开更多
The microstructure, physical and mechanical, and chemical properties of micro-arc calcium phosphate （CAP） coatings deposited under different process voltages in the range of 150-400 V on the commercially pure titani...The microstructure, physical and mechanical, and chemical properties of micro-arc calcium phosphate （CAP） coatings deposited under different process voltages in the range of 150-400 V on the commercially pure titanium （Ti） and Ti-40%Nb （Ti-40Nb） （mass fraction） alloy were investigated by the SEM, TEM, XRD and EDX methods. The coating thickness, roughness, and sizes of structural elements were measured and showed similar linear character depending on the process voltage for the coatings on both substrates. SEM results showed the porous morphology with spherical shape structural elements and rough surface relief of the coatings. XRD and TEM studies exhibited the amorphous structure of the CaP coating. With increasing the process voltage to 300-400 V, the crystalline phases, such as CaHPO4 and β-Ca2P207, were formed onto the coatings. The annealing leads to the formation of complex poly-phase structure with crystalline phases： CaTi4（PO4）6, β-Ca2P2O7, TiP2O7, TiNb（PO4）3, TiO2, NbO2, and Nb2O5. The applied voltage and process duration in the ranges of 200-250 V and 5-10 min, respectively, revealed the coating formed on Ti and Ti-40Nb with optimal properties： thickness of 40-70μm, porosity of 20%-25%, roughness （Ra） of 2.5-5.0 μm, adhesion strength of 15-30 MPa, and Ca/P mole ratio of 0.5-0.7.展开更多
The corrosion behaviors of pure titanium and its weldment welded by tungsten inert gas （TIG） welding in simulated desulfurized flue gas condensates in thermal power plant chimney were investigated using potentiodyna...The corrosion behaviors of pure titanium and its weldment welded by tungsten inert gas （TIG） welding in simulated desulfurized flue gas condensates in thermal power plant chimney were investigated using potentiodynamic polarization, electrochemical impedance spectroscopy （EIS） and immersion tests. The effects of heat input and shielding gases on the corrosion behavior of the welded titanium were also studied. Grain coarsening and Widmanst^itten structure were found in both the fusion zone and the heat-affected zone. The welded titanium exhibited active-passive behavior in the simulated condensates. Both the polarization curves and EIS measurements confirmed that TIG welding process with different parameters had few effects on the corrosion behavior. It was proved that the microstructure changes were not the key material factors affecting the corrosion behavior of pure titanium under the test conditions, while the oxide film had remarkable effect on improving the corrosion resistance.展开更多
Commercially pure titanium（CP Ti） has been actively used in the plate heat exchanger due to its light weight, high specific strength, and excellent corrosion resistance. However, researches for the plastic deformati...Commercially pure titanium（CP Ti） has been actively used in the plate heat exchanger due to its light weight, high specific strength, and excellent corrosion resistance. However, researches for the plastic deformation characteristics and press formability of the CP Ti sheet are not much in comparison with automotive steels and aluminum alloys. The mechanical properties and hardening behavior evaluated in stress-strain relation of the CP Ti sheet are clarified in relation with press formability. The flow curve denoting true stress-true strain relation for CP Ti sheet is fitted well by the Kim-Tuan hardening equation rather than Voce and Swift models. The forming limit curve（FLC） of CP Ti sheet as a criterion for press formability was experimentally evaluated by punch stretching test and analytically predicted via Hora＇s modified maximum force criterion. The predicted FLC by adopting Kim-Tuan hardening model and appropriate yield function shows good correlation with the experimental results of punch stretching test.展开更多
Since titanium has high affinity for hydrogen and reacts reversibly with hydrogen,the precipitation of titanium hydrides in titanium and its alloys cannot be ignored.Two most common hydride precipitates in α-Ti matrix...Since titanium has high affinity for hydrogen and reacts reversibly with hydrogen,the precipitation of titanium hydrides in titanium and its alloys cannot be ignored.Two most common hydride precipitates in α-Ti matrix areγ-hydride and δ-hydride,however their mechanisms for precipitation are still unclear.In the present study,we find that both γ-hydride and δ-hydride phases with different specific orientations were randomly precipitated in the as-received hot forged commercially pure Ti.In addition,a large amount of the titanium hydrides can be introduced into Ti matrix with selective precipitation by using electrochemical treatment.Cs-corrected scanning transmission electron microscopy is used to study the precipitation mechanisms of the two hydrides.It is revealed that the γ-hydride and δ-hydride precipitations are both formed through slip+shuffle mechanisms involving a unit of two layers of titanium atoms,but the difference is that the γ-hydride is formed by prismatic slip corresponding to hydrogen occupying the octahedral sites of α-Ti,while the δ-hydride is formed by basal slip corresponding to hydrogen occupying the tetrahedral sites ofα-Ti.展开更多
The surface nanostructures of commercial pure titanium was realized by the modified shot peening equipment commonly used in industry through the special treatment process. The results show that high-energy-shot-peenin...The surface nanostructures of commercial pure titanium was realized by the modified shot peening equipment commonly used in industry through the special treatment process. The results show that high-energy-shot-peening(HESP) commonly used to prepare nanostructured surface layers can be achieved by the increase of pill size, pill speed, and treatment time in the commercial shot peening equipment. XRD, SEM and TEM were used to characterize the surface layer microstructure of treated specimens. The analytic results show that the main deformation mode of commercial pure Ti is twinning. At the beginning of deformation, the dislocations are formed and twins occur within or on plane, then twins in intersection plane appear, and at last the twin characteristics disappear in the surface layer after longer treatment time. The deformation layer depth increases with treatment time in a certain period when the pill size and speed are unchanged. And in the severe plastic deformation (SPD) layer in which the twins are not identified easily by using SEM, the nanocrystalline microstructures are found under TEM. The finest grain size in the surface layer is about 40 nm, and the depth of nanostructured layers is over 60 μm. The microhardness of the nanostructured surface layers is enhanced significantly after shot peening compared with that of the initial simple.展开更多
A niobium-modified layer on pure titanium surface was obtained by means of double glow plasma surface alloying technique. The modified layer was uniform, continuous, compact and well adhered to the substrate. The niob...A niobium-modified layer on pure titanium surface was obtained by means of double glow plasma surface alloying technique. The modified layer was uniform, continuous, compact and well adhered to the substrate. The niobium composition in the modified layer decreased gradually from the surface to the substrate. The oxidation behavior of the niobium-modified layer was investigated and com- pared with the untreated surface at 900 ~C for 100 h. Characterization of the layers was performed using X-ray diffraction and scanning electron microscope, respectively. The test results show that the oxidation behavior of pure titanium was improved by niobium alloying process. Niobium has a positive influence on the oxidation resistance.展开更多
基金supports from the National Natural Science Foundation of China(No.52404382)the Key Research and Development Project of Shaanxi Province(No.2023-YBGY-090).
文摘Pure titanium fabricated by powder metallurgy generally encounters problems including low relative density and low strength,which limits its application performance.This work proposed a multi-step pressing(MSP)technique for developing highstrength pure titanium.The MSP processes of spherical Ti powders of 15–53μm,53–105μm,and 75–180μm were systematically investigated through multi-particle fnite element method(MPFEM)compared with conventional one-step pressing(OSP)technique.The relative density,phase constitution,microstructure,and compressive mechanical properties of the sintered bulk pure titanium were characterized.Simulation results demonstrate that the MSP technique signifcantly increases the relative density of green compacts by 3.2%,3.3%,and 5.2%,respectively,compared with OSP technique.Experimental results indicate the relative density of the sintered specimens prepared by MSP spherical powders increases by 5.4%,4.5%,and 4.5%,respectively,compared to OSP,and the yield strength improves by 16%,13%,and 18%.For the sintered specimens prepared by MSP irregular powder of 15–53μm,the relative density increases by 6.0%and the yield strength increases by 15%.The enhancement of relative density and yield strength is mainly because the MSP technique mitigates stress concentration between powder particles.Compared to spherical powder,irregular powder exhibits stronger mechanical interlocking owing to the greater propensity for displacement and deformation,which facilitates mutual wedging and interlocking,resulting in superior strength performance.
基金financially supported by the National Key Research and Development Project of the Ministry of Science and Technology of China(No.2022YFB4601000)the Fundamental Research Funds for the Central Universities(No.2042023kf0103)the Ministry of Trade,Industry and Energy,Korea(No.20013095)。
文摘The features of additive manufacturing(AM)have made commercially pure titanium(CP-Ti)an attractive candidate material for biomedical implants.However,achieving high strength and ductility is challenging because of the columnar structures and fine martensite formation.This study investigated the effect of carbon nanotubes(CNTs)addition on the microstructure and mechanical properties of grade 1 CP-Ti(Gr-1)during the laser powder bed fusion(L-PBF)process.A minute amount of 0.2%mass fraction(wt%)CNTs addition resulted in a high yield strength of approximately 700 MPa and exceptional ductility of 25.7%.Therein,a portion of the CNTs dissolved in the matrix as solute atoms,contributing to solution strengthening,while others were transformed into Ti C_(x)through an in situ reaction with the Ti matrix.Furthermore,the addition of CNTs resulted in the formation of a larger fraction of equiaxed grains and increased the activity of basal and prismatic slip systems.Hence,Gr-1 with CNTs exhibited significantly increased ductility while maintaining a high strength comparable to that of Gr-1 without CNTs.The insights gained from this study provide a novel approach for designing strong and ductile Ti alloys for AM.
基金Project(SKLSP200906) supported by the Fund of State Key Laboratory of Solidification Processing in NWPUProject(B08040) supported by Program of Introducing Talents of Discipline in the Project of Advanced Materials and Their Forming Technology
文摘The development of microstructure and texture during cold deep drawing of commercially pure titanium（CP-Ti） was investigated.Three parts,stretching region,drawing region and flange region,were sequentially formed in the deep drawing process of the hemispheric surface part,with reference to deformation modes and strain regimes.Results show that the plastic strain is accommodated by dislocation slip and deformation twinning in the whole deep drawing process.The texture of the CP-Ti sheet and its drawn part consists of rolling texture component and recrystallization texture component.The intensity and type of the initial texture varied during the drawing process are related to the production of deformation twinning and dislocation slip.Twinning weakens the initial texture by randomizing the orientations of crystals,especially for the recrystallization texture.The recrystallization texture in the drawing region disappears due to the significant forming of twinning.Furthermore,over drawing would result in the predominance of dislocation slip and the texture is strengthened.
基金Project(2014CB644003)supported by the National Basic Research Program of ChinaProject(51321003)supported by the National Natural Science Foundation of ChinaProject(B06025)supported by"111"Project of China
文摘Titanium with gradient nano-to-micron scale grains from surface to matrix was fabricated by surface mechanical grinding treatment(SMGT) at room temperature.The SMGT-treated titanium shows higher strength than that of as-received one,but moderate ductility between those of ultra-fine grained(UFG) and coarse-grained titanium.Tensile stress-strain curves of SMGT-treated titanium show double strain hardening regimes.The strain hardening rate(dσ/dε) decreases with increasing strain in tensile deformation.The high strain hardening rate at initial yielding is attributed to nano-to-micron-grained surface layer.The low strain hardening rate at large plastic strain regime primarily results from coarse-grained matrix.The SMGT-treated titanium shows a ductile fracture mode with a large number of dimples.The small size of dimples in the treated surface layer is due to the combination of the high strength and strain hardening exponent.The difference between dimple size in nano-to-micron-grained surface layer and coarse-grained matrix is discussed in terms of plastic zone size at the tip of crack in the SMGT-treated titanium.
文摘In order to reveal the differences caused by forging and rolling process for titanium ingots, hot compression behavior, mechanical properties and the microstructures of forged billets and rolled ones were investigated in detail using Gleeble-1500 thermal mechanical simulator, universal testing machine and optical microscope （OM）. The compression deformation experimental data of commercially pure titanium （CP-Ti） were mapped to be a T vs lg diagram in which data fall into three distinct regions, i.e., three-stage work hardening, two-stage work hardening and flow softening, which can be separated by border lines at 17.5 and 15.4 for lg Z, where Z represents the Zener-Hollomon parameter. The deformation twin is found to have higher Z-value corresponding to the work hardening region. The differences in microstructures and mechanical properties for two kinds of billets indicate that forged billet consists of deformation twins and some twin intersections, and many twins cross the grain boundaries. However, nearly no twins can be seen in the microstructure of billet formed by rolling under optical microscope （OM）, but there are equiaxed and platelike grains. Tensile tests and Vickers hardness test indicate that yield strength, tensile strength and microhardness of the samples after forging are higher than those after rolling.
文摘TA2 pure titanium was chosen to research the interaction among deformation, recrystallization and phase transformation during hot compression. The samples were hot compressed by thermal simulation method with different processing parameters. Variant selection induced by stress during cooling after compression was found. The prismatical texture component which featured that the [0001] direction perpendicular to the compressing direction produced preferentially under the compressing stress. As a result, the transformedα phase possesses strong prismatical texture which is different with the basal texture of compressed αphase. The minimum elastic strain energy is demonstrated to be the main reason that causes the variant selection. Dynamic recrystallization behavior and microstructure evolution during hot compression were also studied.
基金Projects(51505046,51421001)supported by the National Natural Science Foundation of China
文摘The effects of cold rolling and annealing on the microstructure and textural evolution of a commercially pure titanium（CP-Ti） sheet were investigated. Electron backscatter diffractometry demonstrates that the deformation during rolling is accommodated by twinning and slip. Additionally, twinning is the dominant deformation mechanism when the cold rolling reduction is less than 40%. During rolling, {11ˉ22}11ˉ2ˉ3contraction twinning（CT） and {10ˉ12}10ˉ11 extension twinning（ET） are activated. And, the intensity of the（0002） pole along the ND gradually increases with increasing deformation. During annealing, the fraction of low angle grain boundaries（LAGBs） and the intensity of the（0002） pole along the ND gradually decrease slightly with increasing annealing time, while twinning lamellae disappear rapidly. When the annealing time reaches 60 min, 20% cold-rolled sheet recrystallizes almost completely.
文摘Key Laboratory for Beam Technology and Materials Modification, Institute ofLow Energy Nuclear Physics, Beijing Normal UniversityThe morphology, composition, and phase structure of the oxide coatings produced on the surface ofpure titanium by alternating-current microarc discharge in aluminate solution were investigated byX-ray diffraction and scanning electron microscopy. The profiles of the hardness H and the elasticmodulus E in the coatings were determined using a nanoindentation method. The concentrationdistributions of Ti, Al, and O in the coating show that this coating over 30 mu m thick contains twolayers: an outer layer and an inner layer. The oxide coating is mainly composed of TiO_2 rutile andAl_2TiO_5 compounds. During oxidation, the temperature in the microarc discharge channel was veryhigh to make the local coating molten. From the surface to the interior of the coating, H and Eincrease gradually, and then reach maximum values of 9.78 GPa and 176 GPa respectively at a distanceof 7 mu m from the coating/titanium interface. They are also rather high near the interface.
文摘Equal channel angular pressing(ECAP)is one of the most effective processes to produce ultra-fine grain(UFG)and nanocrystalline(NC)materials.Because the commercially pure titanium exhibits excellent biocompatibility properties,it has a significant potential to be utilized as an implant material.The low static and dynamic strengths of the pure titanium are one of the weaknesses of this material.This defect can be removed by applying the ECAP process on the pure titanium.In this work,the commercially pure titanium Grade2(CP-Ti of Grade2)was pressed at room temperature by the ECAP process via a channel angle of135°for3passes.The microstructural analysis and mechanical tests such as tensile test,hardness test,three-point bending test and Charpy impact test were all carried out on the ECAPed CP-Ti through3passes.The microstructural evolution reveals that by applying the ECAP process,coarse grain(CG)structure develops to UFG/NC structure.Moreover,the results of the mechanical tests show that the process significantly increases the yield and ultimate tensile strengths,bending strength,hardness and fracture toughness of the commercially pure titanium so that it can be used as a replacement for metallic alloys used as biomaterials.
基金Project(J51504) supported by Shanghai Leading Academic Discipline Project,China
文摘In order to establish the rolling process parameters of grade-2 commercially pure titanium （CP-Ti）, it is necessary to understand the transformation mechanism and mechanical properties of this material. The β→α transformation kinetics of the grade-2 CP-Ti during continuous cooling was measured and its hot compression behavior was investigated using Gleeble-1500 thermal mechanical simulator. Dynamic CCT diagram confirms that cooling rate has an obvious effect on the start and finishing transformation and microstructures at room temperature. The critical cooling rate for γ-phase transforms to a phase is about 15℃/s. When the cooling rate is higher than 15 ℃/s, some β phases with fine granular shape remain residually into plate-like structure. The plate-like a phase forms at cooling rate lower than 2 ℃/s, serrate a phase forms at medium cooling rates, about 5-15℃/s. The flow stress behavior of grade-2 CP-Ti was investigated in a temperature range of 700-900℃ and strain rate of 3.6-40 mm/min. The results show that dynamic recrystallization, dynamic recovery and work-hardening obviously occur during hot deformation. Constitutive equation of grade-2 CP-Ti was established by analyzing the relationship of the deformation temperature, strain rate, deformation degree and deformation resistance.
基金financially supported by the National Natural Science Foundation of China (No.52104372)the Fundamental Research Funds for the Central Universities,China (No.N2107001)the China Postdoctoral Science Foundation (No.2019M651129)。
文摘The strength of traditional commercially pure titanium(CP-Ti) alloys often fails to meet the demand of structural materials. In order to enhance their mechanical properties, the cold-rolled CP-Ti alloys were annealed at different temperatures, and the recrystallization behavior and texture evolution were investigated. It was found that the bimodal microstructure(equiaxed and elongated grains) was formed after partial recrystallization, and the corresponding sample exhibited an excellent combination of ultimate tensile strength(702 MPa) and total elongation(36.4%). The recrystallization nucleation of CP-Ti sheets occurred preferentially in the high strain and the high-angle grain boundaries(HAGBs) regions. Meanwhile, the internal misorientations of the deformed heterogeneous grains increased and transformed into HAGBs, which further promoted the recrystallization nucleation. The main recrystallization texture was basal TD-split texture transformed from cold-rolled basal RD-split texture, and the oriented nucleation played a dominated role during recrystallization.
文摘The specimens cut from the cold-rolled pure titanium sheet at 0°,45°and 90°to the rolling direction were treated by high density electropulsing(maximum current density J=(7.22-7.96)×10^(3)A/mm^(2),pulse period t_(p)=110μs).The mechanical properties and microstructures of the cold-rolled,electropulsed and conventional annealed commercially pure titanium sheet were examined by using uniaxial tension test machine and optical microscope(OM),respectively.The results show that the deformation behavior of the electropulsed pure titanium sheet is significantly different from that of conventional annealed pure titanium sheet.The difference of the mechanical properties between the 0°,45°and 90°direction specimens is almost diminished.It is mainly due to the increase in dislocation mobility and formation of lamellar microstructure after the electropulsing.
基金Project(DMR-0968825)support by National Science Foundation Through Grant
文摘A review on severe plastic deformation（SPD） technique of equal channel angular pressing（ECAP） process of commercially pure titanium（CP-Ti） alloys was presented with a major emphasize on the influence of ECAP parameters that include channel and curvature angles, processing route, temperature of operation, pressing speed, internal heating, number of pass through the die and back pressure. Various ECAP characteristics such as microstructure, strain inhomogeneity and mechanical properties are considered to achieve the maximum homogeneity, equilibrium grain refinement and mechanical improvement of CP-Ti. Investigations show that a pressing speed of 1-3 mm/s at 450 °C with route BC along with channel and curvature angles of 90° and 20° respectively with backpressure can lead to the most homogeneous ultrafine microstructure.
基金financial support from the Shenzhen Development and Reform Commission Engineering Laboratory Project(Shenzhen development and Reform2015-1033)the Shenzhen Science and Technology supporting Plan Project(GJHS20160331183313435)the China Postdoctoral Science Foundation(No.2017M620770)
文摘The effects of electropulsing-assisted ultrasonic surface rolling process on surface mechanical properties andmicrostructure evolution of commercial pure titanium were investigated. It was found that the surface mechanical prop-erties were significantly enhanced compared to traditional ultrasonic surface rolling process （USRP）, leading to smallersurface roughness and smoother morphology with fewer cracks and defects. Moreover, surface strengthened layer wasremarkably enhanced with deeper severe plastic deformation layer and higher surface hardness. Remarkable enhancementsof surface mechanical properties may be related to the gradient refined microstructure, the enhanced severe plasticdeformation layer and the accelerated formation of sub-boundaries and twins induced by coupling effects of USRP andelectropulsing. The primary intrinsic reasons for these improvements may be attributed to the thermal and athermal effectscaused by electropulsing treatment, which would accelerate dislocation mobility and atom diffusion.
基金Project(III.23.2.5)supported by the Fundamental Research Program of the Siberian Branch of Russian Academy of SciencesProject(15-03-07659)supported by the Russian Foundation for Basic Research+1 种基金Project(CR16-22)supported by the China and Russia on the Implementation of Inter-governmental ScientificTechnological Cooperation Projects of the Notice(NSC foreign word[2012]No.269)
文摘The microstructure, physical and mechanical, and chemical properties of micro-arc calcium phosphate （CAP） coatings deposited under different process voltages in the range of 150-400 V on the commercially pure titanium （Ti） and Ti-40%Nb （Ti-40Nb） （mass fraction） alloy were investigated by the SEM, TEM, XRD and EDX methods. The coating thickness, roughness, and sizes of structural elements were measured and showed similar linear character depending on the process voltage for the coatings on both substrates. SEM results showed the porous morphology with spherical shape structural elements and rough surface relief of the coatings. XRD and TEM studies exhibited the amorphous structure of the CaP coating. With increasing the process voltage to 300-400 V, the crystalline phases, such as CaHPO4 and β-Ca2P207, were formed onto the coatings. The annealing leads to the formation of complex poly-phase structure with crystalline phases： CaTi4（PO4）6, β-Ca2P2O7, TiP2O7, TiNb（PO4）3, TiO2, NbO2, and Nb2O5. The applied voltage and process duration in the ranges of 200-250 V and 5-10 min, respectively, revealed the coating formed on Ti and Ti-40Nb with optimal properties： thickness of 40-70μm, porosity of 20%-25%, roughness （Ra） of 2.5-5.0 μm, adhesion strength of 15-30 MPa, and Ca/P mole ratio of 0.5-0.7.
基金supported by the National Natural Science Foundation of China (No.51131008)
文摘The corrosion behaviors of pure titanium and its weldment welded by tungsten inert gas （TIG） welding in simulated desulfurized flue gas condensates in thermal power plant chimney were investigated using potentiodynamic polarization, electrochemical impedance spectroscopy （EIS） and immersion tests. The effects of heat input and shielding gases on the corrosion behavior of the welded titanium were also studied. Grain coarsening and Widmanst^itten structure were found in both the fusion zone and the heat-affected zone. The welded titanium exhibited active-passive behavior in the simulated condensates. Both the polarization curves and EIS measurements confirmed that TIG welding process with different parameters had few effects on the corrosion behavior. It was proved that the microstructure changes were not the key material factors affecting the corrosion behavior of pure titanium under the test conditions, while the oxide film had remarkable effect on improving the corrosion resistance.
基金supported by the National Research Foundation of Korea (NRF) granted by the Korea government [2014R1A2A2A01005903]Priority Research Centers Program (2010-0020089)support from a grant [R0003356] (Tuning Professional Support Center in Daegu Metropolitan City) funded by the Ministry of Trade, Industry and Energy (MOTIE, Korea)
文摘Commercially pure titanium（CP Ti） has been actively used in the plate heat exchanger due to its light weight, high specific strength, and excellent corrosion resistance. However, researches for the plastic deformation characteristics and press formability of the CP Ti sheet are not much in comparison with automotive steels and aluminum alloys. The mechanical properties and hardening behavior evaluated in stress-strain relation of the CP Ti sheet are clarified in relation with press formability. The flow curve denoting true stress-true strain relation for CP Ti sheet is fitted well by the Kim-Tuan hardening equation rather than Voce and Swift models. The forming limit curve（FLC） of CP Ti sheet as a criterion for press formability was experimentally evaluated by punch stretching test and analytically predicted via Hora＇s modified maximum force criterion. The predicted FLC by adopting Kim-Tuan hardening model and appropriate yield function shows good correlation with the experimental results of punch stretching test.
基金This work was supported financially by the National Natural Science Foundation of China(Nos.51621003,11374028and U1330112)the Scientific Research Key Program of Beijing Municipal Commission of Education(No.KZ201310005002)+1 种基金the Beijing Municipal Found for Scientific Innovation(No.PXM2019014204500031)the Foundation on the Creative Research Team Construction Promotion Project of Beijing Municipal Institution(No.IDHT20190503)。
文摘Since titanium has high affinity for hydrogen and reacts reversibly with hydrogen,the precipitation of titanium hydrides in titanium and its alloys cannot be ignored.Two most common hydride precipitates in α-Ti matrix areγ-hydride and δ-hydride,however their mechanisms for precipitation are still unclear.In the present study,we find that both γ-hydride and δ-hydride phases with different specific orientations were randomly precipitated in the as-received hot forged commercially pure Ti.In addition,a large amount of the titanium hydrides can be introduced into Ti matrix with selective precipitation by using electrochemical treatment.Cs-corrected scanning transmission electron microscopy is used to study the precipitation mechanisms of the two hydrides.It is revealed that the γ-hydride and δ-hydride precipitations are both formed through slip+shuffle mechanisms involving a unit of two layers of titanium atoms,but the difference is that the γ-hydride is formed by prismatic slip corresponding to hydrogen occupying the octahedral sites of α-Ti,while the δ-hydride is formed by basal slip corresponding to hydrogen occupying the tetrahedral sites ofα-Ti.
基金Project(50171017) support by the National Natural Science Foundation of China project(2001101054) supported by the Science and Technology Foundation of Liaoning Province project(02H25008) supported by the Aeronautical Basic Science Foundation
文摘The surface nanostructures of commercial pure titanium was realized by the modified shot peening equipment commonly used in industry through the special treatment process. The results show that high-energy-shot-peening(HESP) commonly used to prepare nanostructured surface layers can be achieved by the increase of pill size, pill speed, and treatment time in the commercial shot peening equipment. XRD, SEM and TEM were used to characterize the surface layer microstructure of treated specimens. The analytic results show that the main deformation mode of commercial pure Ti is twinning. At the beginning of deformation, the dislocations are formed and twins occur within or on plane, then twins in intersection plane appear, and at last the twin characteristics disappear in the surface layer after longer treatment time. The deformation layer depth increases with treatment time in a certain period when the pill size and speed are unchanged. And in the severe plastic deformation (SPD) layer in which the twins are not identified easily by using SEM, the nanocrystalline microstructures are found under TEM. The finest grain size in the surface layer is about 40 nm, and the depth of nanostructured layers is over 60 μm. The microhardness of the nanostructured surface layers is enhanced significantly after shot peening compared with that of the initial simple.
文摘A niobium-modified layer on pure titanium surface was obtained by means of double glow plasma surface alloying technique. The modified layer was uniform, continuous, compact and well adhered to the substrate. The niobium composition in the modified layer decreased gradually from the surface to the substrate. The oxidation behavior of the niobium-modified layer was investigated and com- pared with the untreated surface at 900 ~C for 100 h. Characterization of the layers was performed using X-ray diffraction and scanning electron microscope, respectively. The test results show that the oxidation behavior of pure titanium was improved by niobium alloying process. Niobium has a positive influence on the oxidation resistance.
