In high-altitude nuclear detonations,the proportion of pulsed X-ray energy can exceed 70%,making it a specific monitoring signal for such events.These pulsed X-rays can be captured using a satellite-borne X-ray detect...In high-altitude nuclear detonations,the proportion of pulsed X-ray energy can exceed 70%,making it a specific monitoring signal for such events.These pulsed X-rays can be captured using a satellite-borne X-ray detector following atmospheric transmission.To quantitatively analyze the effects of different satellite detection altitudes,burst heights,and transmission angles on the physical processes of X-ray transport and energy fluence,we developed an atmospheric transmission algorithm for pulsed X-rays from high-altitude nuclear detonations based on scattering correction.The proposed method is an improvement over the traditional analytical method that only computes direct-transmission X-rays.The traditional analytical method exhibits a maximum relative error of 67.79% compared with the Monte Carlo method.Our improved method reduces this error to within 10% under the same conditions,even reaching 1% in certain scenarios.Moreover,its computation time is 48,000 times faster than that of the Monte Carlo method.These results have important theoretical significance and engineering application value for designing satellite-borne nuclear detonation pulsed X-ray detectors,inverting nuclear detonation source terms,and assessing ionospheric effects.展开更多
The temporal response of cadmium-zinc-telluride(CZT) crystals is evaluated at room temperature by using an ultrafast-pulsed x-ray source. The dynamics of carrier relaxation in a CZT single crystal is modeled at a micr...The temporal response of cadmium-zinc-telluride(CZT) crystals is evaluated at room temperature by using an ultrafast-pulsed x-ray source. The dynamics of carrier relaxation in a CZT single crystal is modeled at a microscopic level based on a multi-trapping effect. The effects of the irradiation flux and bias voltage on the amplitude and full width at half maximum(FWHM) of the transient currents are investigated. It is demonstrated that the temporal response process is affected by defect level occupation fraction. A fast photon current can be achieved under intense pulsed x-ray irradiation to be up to 2.78×10~9 photons mm-2·s-1. Meanwhile, it is found that high bias voltage could enhance carrier detrapping by suppressing the capture of structure defects and thus improve the temporal response of CZT detectors.展开更多
Unstable mechanical structure,low energy efficiency,and cooling requirements limit the application of conventional x-ray tubes based on filament as cathode in several academic areas.In this paper,we demonstrate a ligh...Unstable mechanical structure,low energy efficiency,and cooling requirements limit the application of conventional x-ray tubes based on filament as cathode in several academic areas.In this paper,we demonstrate a light-controlled pulsed x-ray tube using multialkali cathode as electron generator.The photocathode active area of the light controlled x-ray tube is 13.2 cm^(2)(41 mm in diameter),which provides high photoelectron-emitting efficiency up to 0.288 mA/lm in 460-nm LED and 2.37-mA maximum tube current.Furthermore,the modulation ability from 1 kHz to 100 kHz of the x-ray tube is tested.The results suggest that the light-controlled pulsed x-ray tube has easy modulation and short x-ray pulse properties and is promising to be the next generation x-ray tube with wide applications in medical radiation therapy as well as the calibration for detectors and scintillators.展开更多
Low-density short-duration pulsed current-assisted aging treatment was applied to the Ti-6Al-4V-0.5Mo-0.5Zr alloy subjected to different solution treatments.The results show that numerous α_(p) phases redissolve into...Low-density short-duration pulsed current-assisted aging treatment was applied to the Ti-6Al-4V-0.5Mo-0.5Zr alloy subjected to different solution treatments.The results show that numerous α_(p) phases redissolve into the new β phase during the pulsed current-assisted aging process,and then the newly formed β phase is mainly transformed into the β_(t) phase,with occasional transition to new α_(p) phase,leading to a remarkable grain refinement,especially for the lamellarαs phases.In comparison to conventional aging treatment,the pulsed current-assisted aging approach achieves a significant enhancement in strength without degrading ductility,yielding an excellent mechanical property combination:a yield strength of 932 MPa,a tensile strength of 1042 MPa,and an elongation of 12.2%.It is primarily ascribed to the increased fraction of β_(t) phases,the obvious grain refinement effect,and the slip block effect induced by the multiple-variantαs colonies distributed within β_(t) phases.展开更多
Pulsed dynamic electrolysis(PDE),driven by renewable energy,has emerged as an innovative electrocatalytic conversion method,demonstrating significant potential in addressing global energy challenges and promoting sust...Pulsed dynamic electrolysis(PDE),driven by renewable energy,has emerged as an innovative electrocatalytic conversion method,demonstrating significant potential in addressing global energy challenges and promoting sustainable development.Despite significant progress in various electrochemical systems,the regulatory mechanisms of PDE in energy and mass transfer and the lifespan extension of electrolysis systems,particularly in water electrolysis(WE)for hydrogen production,remain insufficiently explored.Therefore,there is an urgent need for a deeper understanding of the unique contributions of PDE in mass transfer enhancement,microenvironment regulation,and hydrogen production optimization,aiming to achieve low-energy consumption,high catalytic activity,and long-term stability in the generation of target products.Here,this review critically examines the microenvironmental effects of PDE on energy and mass transfer,the electrode degradation mechanisms in the lifespan extension of electrolysis systems,and the key factors in enhancing WE for hydrogen production,providing a comprehensive summary of current research progress.The review focuses on the complex regulatory mechanisms of frequency,duty cycle,amplitude,and other factors in hydrogen evolution reaction(HER)performance within PDE strategies,revealing the interrelationships among them.Finally,the potential future directions and challenges for transitioning from laboratory studies to industrial applications are proposed.展开更多
Synchrotron method of resonant X-ray reflectivity 2D mapping has been applied to study ultrathin epitaxial layers of WS_(2)grown by pulsed laser deposition on Al_(2)O_(3)(0001)substrates.The measurements were carried ...Synchrotron method of resonant X-ray reflectivity 2D mapping has been applied to study ultrathin epitaxial layers of WS_(2)grown by pulsed laser deposition on Al_(2)O_(3)(0001)substrates.The measurements were carried out across the L absorption edge of tungsten to perform depth-dependent element-selective analysis sensitive to potential chemical modification of the WS_(2)layer in ambient conditions.Despite the few monolayer thickness of the studied film,the experimentally measured maps of reflectance as a function of incident angle and photon energy turned out to be quite informative showing well-pronounced interference effects near W absorption edge at 10210 eV.The synchrotron studies were complemented with conventional non-resonant reflectance measurements carried out in the laboratory at a fixed photon energy corresponding to Cu Kαemission.The reconstruction of the depth and energy dependent scattering length density within the studied multilayers was carried out using the OpenCL empowered fitting software utilizing spectral shaping algorithm which does not rely on the pre-measured reference absorption spectra.A thin WO_(x) layer has been revealed at the surface of the WS_(2)layer pointing out to the effect of water assisted photo-oxidation reported in a number of works related to ultrathin layers of transition metal dichalcogenides.展开更多
Groups of a typical operational amplifier-μA741 were irradiated in a cobalt unit, each group accumulating a different total ionizing dose （TID）. The results showed that the TID caused power consumption current and ...Groups of a typical operational amplifier-μA741 were irradiated in a cobalt unit, each group accumulating a different total ionizing dose （TID）. The results showed that the TID caused power consumption current and slew rate （SR） to degenerate in ultra-linearity, owing to a severe reduction in the current gain of the internal LPNP transistors. Pulsed X-ray irradiation experiments were carried out on the μA741 groups with different values, and the results revealed that the impact on the response to the pulsed X-ray irradiation was greater when the devices absorbed more TID. The mechanism for this is explained on the basis of the circuit construction of the μA741; the sensitive parameters of the circuit were obtained via simulation on SP1CE. The simulation results additionally showed that if the sensitive parameters were optimized, the duration of interruption caused by the pulsed X-ray irradiation would be reduced significantly. In addition, several proposals are provided for hardening the devices.展开更多
Non-metallic inclusions in steel are a significant challenge,affecting material properties and leading to issues such as stress concentration,cracking,and accelerated corrosion.Current methods for removing inclusions,...Non-metallic inclusions in steel are a significant challenge,affecting material properties and leading to issues such as stress concentration,cracking,and accelerated corrosion.Current methods for removing inclusions,including bubble,electromagnetic stirring,filtration separation,fluid flow,and sedimentation,often struggle with the removal of fine inclusions.Apart from these known methods,pulsed electric current(PEC),as an emerging technology,has demonstrated immense potential and environmental advantages.PEC offers adjustable current parameters and simple equipment,making it an attractive alternative to traditional methods.Its green energy-saving features and excellent results in regulating inclusion morphology and migration,as well as inhibiting submerged entry nozzle(SEN)clogging,make it a promising technology.In comparison to continuous current technology,PEC has shown significant advantages in regulating inclusions,not only improving purification efficiency but also demonstrating outstanding performance in flow stability and energy consumption.The ability of PEC to efficiently reduce inclusion numbers enhances the purity and quality of molten steel,improving its mechanical properties.Currently,the theoretical basis for controlling the movement of inclusions by current is mainly composed of three major theories:the double electric layer theory,electromagnetic force reverse separation theory,and electric free energy drive theory.These theories together form an important framework for researchers to understand and optimize the behavior of impurity movement controlled by electric current.Looking ahead,PEC is expected to pave the way for new solutions in directional regulation of inclusion migration,efficient inclusion removal,SEN clogging prevention,and the purification of molten steel.展开更多
In a pulsed plasma thruster,the voltage distribution between the electrodes is a key factor that influences the ionization process.However,few researchers have conducted in-depth studies of this phenomenon in the past...In a pulsed plasma thruster,the voltage distribution between the electrodes is a key factor that influences the ionization process.However,few researchers have conducted in-depth studies of this phenomenon in the past.Reported here are measurements of the voltage distribution between the plates of a parallel-plate pulsed plasma thruster under different discharge voltages,based on which the variations in the total circuit inductance and resistance as well as those between the plates are calculated.The results show that the time-averaged voltage across the plates accounts for 28.7%-50.4%of the capacitor voltage.As the capacitor initial voltage increases from 1250 V to 2000 V,the voltage across the plates rises,but its proportion relative to the capacitor voltage decreases.For every 250 V increase in the capacitor initial voltage,the average voltage proportion across the plates decreases by approximately 2%-3%.Additionally,the voltage proportion decreases gradually from the end near the propellant outward.The voltage distribution ratio between the plates is correlated with the proportions of the resistance and inductance between the plates relative to the total circuit.展开更多
The transition of hydrogen sourcing from carbon-intensive to water-based methodologies is underway,with renewable energy-powered proton exchange membrane water electrolysis(PEMWE)emerging as the preeminent pathway for...The transition of hydrogen sourcing from carbon-intensive to water-based methodologies is underway,with renewable energy-powered proton exchange membrane water electrolysis(PEMWE)emerging as the preeminent pathway for hydrogen production.Despite remarkable advancements in this field,confronting the sluggish electrochemical kinetics and inherent high-energy consumption arising from deteriorated mass transport within PEMWE systems remains a formidable obstacle.This impediment stems primarily from the hindered protons mass transfer and the untimely hydrogen bubbles detachment.To address these challenges,we harness the inherent variability of electrical energy and introduce an innovative pulsed dynamic water electrolysis system.Compared to constant voltage electrolysis(hydrogen production rate:51.6 m L h^(-1),energy consumption:5.37 kWh Nm-^(3)H_(2)),this strategy(hydrogen production rate:66 m L h^(-1),energy consumption:3.83 kWh Nm-^(3)H_(2))increases the hydrogen production rate by approximately 27%and reduces the energy consumption by about 28%.Furthermore,we demonstrate the practicality of this system by integrating it with an off-grid photovoltaic(PV)system designed for outdoor operation,successfully driving a hydrogen production current of up to 500 mA under an average voltage of approximately 2 V.The combined results of in-situ characterization and finite element analysis reveal the performance enhancement mechanism:pulsed dynamic electrolysis(PDE)dramatically accelerates the enrichment of protons at the electrode/solution interface and facilitates the release of bubbles on the electrode surface.As such,PDE-enhanced PEMWE represents a synergistic advancement,concurrently enhancing both the hydrogen generation reaction and associated transport processes.This promising technology not only redefines the landscape of electrolysis-based hydrogen production but also holds immense potential for broadening its application across a diverse spectrum of electrocatalytic endeavors.展开更多
Pulsed magnet technology is the only way to generate ultra-strong magnetic fields higher than 45 T so far.However,the inherently fast-changing field strength(typically on the order of 1000 T/s)poses significant challe...Pulsed magnet technology is the only way to generate ultra-strong magnetic fields higher than 45 T so far.However,the inherently fast-changing field strength(typically on the order of 1000 T/s)poses significant challenges for spectroscopic measurements which rely on time integration of signals to improve spectral qualities.In this work,we report high-sensitivity spectroscopic measurements under pulsed high magnetic fields employing the long flat-top pulsed magnetic field technique.By means of a multiple-capacitor power supply,we were able to generate pulsed high magnetic fields with controllable flat-top pulse width and field stabilities.By synchronizing spectroscopic measurements with the waveform of the flattop magnetic field,the integration time of each spectrum can be increased by up to 100 times compared with that of the conventional spectroscopic measurements under pulsed magnetic fields,thus enabling high-sensitivity spectroscopic measurements under ultra-strong pulsed magnetic fields.These findings promise an efficient way to significantly improve the performance and extend the application of optical measurements under pulsed high magnetic fields.展开更多
The accelerator-generating 6.13 MeV pulsed Gamma by 19F（p, αγ）160 reaction usually synchronizes with an intense bremsstrahlung x-ray which has a maximum energy of 1 MeV. This paper proposes a new method, named the...The accelerator-generating 6.13 MeV pulsed Gamma by 19F（p, αγ）160 reaction usually synchronizes with an intense bremsstrahlung x-ray which has a maximum energy of 1 MeV. This paper proposes a new method, named the scattering and absorbing method, to diagnose the 6.13 MeV Gamma. This method includes two parts： the detector and a scatterer placed in front of the detector. The detector converts the Gamma to electrons and then collects the electrons by a scintillator. In order to restrain the interference of the low-energy background, the scintillator collects the electrons at a small angle. The scintillator is wrapped with electro-absorbing material to absorb the low-energy electrons generated by background x-rays. The theoretical sensitivity ratio of 6.13 MeV Gamma to 1 MeV x-rays is greater than 150. The scatterer is a pretreatment tool to scatter some background x-rays away from the radial beam before they enter the detector. By varying the length, the scatterer can reduce the background x-rays to an acceptable level for the detector.展开更多
Traditional heat treatment methods require a significant amount of time and energy to affect atomic diffusion and enhance the spheroidization process of carbides in bearing steel,while pulsed current can accelerate at...Traditional heat treatment methods require a significant amount of time and energy to affect atomic diffusion and enhance the spheroidization process of carbides in bearing steel,while pulsed current can accelerate atomic diffusion to achieve ultra-fast spheroidization of carbides.However,the understanding of the mechanism by which different pulse current parameters regulate the dissolution behavior of carbides requires a large amount of experimental data to support,which limits the application of pulse current technology in the field of heat treatment.Based on this,quantify the obtained pulse current processing data to create an important dataset that could be applied to machine learning.Through machine learning,the mechanism of mutual influence between carbide regulation and various factors was elucidated,and the optimal spheroidization process parameters were determined.Compared to the 20 h required for traditional heat treatment,the application of pulsed electric current technology achieved ultra-fast spheroidization of GCr15 bearing steel within 90 min.展开更多
Shielding materials are critical for downhole pulsed neutron tool design because they directly influence the accuracy of formation measurements.A well-designed shield configuration ensures that the response of the too...Shielding materials are critical for downhole pulsed neutron tool design because they directly influence the accuracy of formation measurements.A well-designed shield configuration ensures that the response of the tool is maximally representative of the formation without being affected by the tool and borehole environment.This study investigated the effects of boron-containing materials on neutron and gamma detectors based on a newly designed logging-while-drilling tool that is currently undergoing manufacturing.As the boron content increased,the ability to absorb thermal neutrons increased significantly.Through simulation,it was proven that boron carbide(B_(4)C)can be used as an effective boron shielding material for thermal neutrons,and is therefore employed in this work.To shield against thermal neutrons migrating from the mud pipes,the optimal shielding thicknesses for the near-and far-neutron detectors were determined to be 5 and 4 mm.At a porosity of 25 p.u.,near-neutron sensitivity exhibited a 5.6%increase.Furthermore,to shield the capture gamma generated by thermal neutrons once they enter the tool from the mud pipe and formation,internal and external shields for the gamma detector were evaluated.The results show that the internal shield requires a boron content of 75%,whereas the external shield has a thickness of 14.2 mm thickness and a boron content of 25%to minimize the tool effect.展开更多
The kinetic characteristics of plasma-assisted oxidative pyrolysis of ammonia are studied by using the global/fluid models hybrid solution method.Firstly,the stable products of plasma-assisted oxidative pyrolysis of a...The kinetic characteristics of plasma-assisted oxidative pyrolysis of ammonia are studied by using the global/fluid models hybrid solution method.Firstly,the stable products of plasma-assisted oxidative pyrolysis of ammonia are measured.The results show that the consumption of NH_(3)/O_(2)and the production of N_(2)/H_(2)change linearly with the increase of voltage,which indicates the decoupling of nonequilibrium molecular excitation and oxidative pyrolysis of ammonia at low temperatures.Secondly,the detailed reaction kinetics mechanism of ammonia oxidative pyrolysis stimulated by a nanosecond pulse voltage at low pressure and room temperature is established.Based on the reaction path analysis,the simplified mechanism is obtained.The detailed and simplified mechanism simulation results are compared with experimental data to verify the accuracy of the simplified mechanism.Finally,based on the simplified mechanism,the fluid model of ammonia oxidative pyrolysis stimulated by the nanosecond pulse plasma is established to study the pre-sheath/sheath behavior and the resultant consumption and formation of key species.The results show that the generation,development,and propagation of the pre-sheath have a great influence on the formation and consumption of species.The consumption of NH_(3)by the cathode pre-sheath is greater than that by the anode pre-sheath,but the opposite is true for OH and O(1S).However,within the sheath,almost all reactions do not occur.Further,by changing the parameters of nanosecond pulse power supply voltage,it is found that the electron number density,electron current density,and applied peak voltages are not the direct reasons for the structural changes of the sheath and pre-sheath.Furthermore,the discharge interval has little effect on the sheath structure and gas mixture breakdown.The research results of this paper not only help to understand the kinetic promotion of non-equilibrium excitation in the process of oxidative pyrolysis but also help to explore the influence of transport and chemical reaction kinetics on the oxidative pyrolysis of ammonia.展开更多
Type-II Dirac semimetal PtTe2is a promising candidate for various electronic device applications due to its high carrier mobility,high conductivity,and air stability.In this work,we report on the growth of large-scale...Type-II Dirac semimetal PtTe2is a promising candidate for various electronic device applications due to its high carrier mobility,high conductivity,and air stability.In this work,we report on the growth of large-scale PtTe_(2)films by the pulsed laser deposition(PLD)and the comparison of the magnetotransport properties with the PtTe2films grown by the chemical vapor deposition(CVD).The low-temperature Hall curves of the PLD-grown films exhibit a linear behavior,in contrast with the nonlinear characteristic of the Hall behavior observed in CVD-grown films,in which a defect gradient is introduced.Meanwhile,both PtTe2films show weak antilocalization at low temperatures,which is attributed to the strong spin–orbit coupling.展开更多
In this work,we aim to develop a novel post-treatment process combining cryogenic and pulsed electric field treatment to enhance WC-Co cemented carbides.The results show a 15.62%increase in hardness from 1831.38 to 21...In this work,we aim to develop a novel post-treatment process combining cryogenic and pulsed electric field treatment to enhance WC-Co cemented carbides.The results show a 15.62%increase in hardness from 1831.38 to 2117.38 HV30,a 9.60%rise in fracture toughness from 9.06 to 9.93 MPa·m^(1/2),while the friction coefficient decreases from 0.63 to 0.47.Through the residual stress evolution,WC orientation change and the martensitic transformation of Co,and the internal enhancement mechanism of cryogenic combined with pulsed electric field treatment are revealed.The electron wind generated by the pulsed electric field can efficiently reduce the residual stress induced by cryogenic process.The evolution of residual stress promotes the base slip of WC,increasing the degree of{0001}orientation.In addition,the degree of martensitic transformation of Co intensifies,with the hcp-Co/fcc-Co ratio rising from 0.41%to 17.86%.The enhanced WC{0001}orientation and increased hcp-Co content contribute to significant improvements in hardness and wear resistance.This work provides a novel efficient enhancement strategy for ceramics and alloys,with the potential to be a mainstream strengthening method in the future.展开更多
The complicated structure of electronic devices makes the conventional annealing method,which involves placing the entire device in a furnace,insufficient for achieving the desired quality.This issue is currently addr...The complicated structure of electronic devices makes the conventional annealing method,which involves placing the entire device in a furnace,insufficient for achieving the desired quality.This issue is currently addressed through the use of pulsed laser annealing,where a specific target layer is heated,preventing the overheating of other layers or the substrate.However,this method is only applicable to a very limited range of materials and requires very expensive,powerful pulsed laser sources.Herein,a novel approach for the selective local thermal treatment of thin films is proposed;in this method,short,powerful current pulses are applied to the target conductive layer.The application of two current pulses with a length of 1.5 s induced the crystallization of a 160-nm thick indium tin oxide(ITO)film,resulting in a sheet resistance of 8.68Ω·sq^(-1),an average visible light transmittance of 86.69%,and a figure of merit(FoM)of 293.61.This FoM is an order of magnitude higher than that of the as-prepared ITO film,and to the best of our knowledge,is among the highest reported values for the polycrystalline ITO films.Simulations have shown that even faster and more localized crystallization could be achieved by increasing the power of pulsed current.This novel annealing method is applicable to most semi-conductive or metallic thin films and requires only a relatively inexpensive pulsed current source,making it potentially more attractive than pulsed laser annealing.展开更多
Avoiding crystallization while maintaining the original microstructure and mechanical properties of the material are long-term goals of laser welding of Zr-based bulk metallic glass(BMG).In this paper,the effect of pu...Avoiding crystallization while maintaining the original microstructure and mechanical properties of the material are long-term goals of laser welding of Zr-based bulk metallic glass(BMG).In this paper,the effect of pulsed laser welding parameters on the microstructure,crystallization degree,and mechanical properties of Zr57Nb5Cu15.4Ni12.6Al10 BMG is investigated.Non-crystallized welding forming of a zirconium-based amorphous alloy is achieved by optimizing the process parameters of pulsed laser welding.The crystallization degree of Zr-based BMG is mainly determined by the welding speed and power.The welding depth and crystallization area fraction increase with an increase in the effective peak power density.The optimized welding process can effectively reduce the heat accumulation of the weld,thus avoiding crystallization.The flexural strength of the weld can be maintained at 96.5%of the matrix.展开更多
文摘In high-altitude nuclear detonations,the proportion of pulsed X-ray energy can exceed 70%,making it a specific monitoring signal for such events.These pulsed X-rays can be captured using a satellite-borne X-ray detector following atmospheric transmission.To quantitatively analyze the effects of different satellite detection altitudes,burst heights,and transmission angles on the physical processes of X-ray transport and energy fluence,we developed an atmospheric transmission algorithm for pulsed X-rays from high-altitude nuclear detonations based on scattering correction.The proposed method is an improvement over the traditional analytical method that only computes direct-transmission X-rays.The traditional analytical method exhibits a maximum relative error of 67.79% compared with the Monte Carlo method.Our improved method reduces this error to within 10% under the same conditions,even reaching 1% in certain scenarios.Moreover,its computation time is 48,000 times faster than that of the Monte Carlo method.These results have important theoretical significance and engineering application value for designing satellite-borne nuclear detonation pulsed X-ray detectors,inverting nuclear detonation source terms,and assessing ionospheric effects.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.51702271 and U1631116)the Young and Middle-aged Teachers Education and Scientific Research Foundation of Fujian Province,China(Grant No.JAT170407)+1 种基金the High Level Talent Project of Xiamen University of Technology,China(Grant No.YKJ16016R)the Fund of the State Key Laboratory of Solidification Processing in NWPU,China(Grant No.SKLSP201741)
文摘The temporal response of cadmium-zinc-telluride(CZT) crystals is evaluated at room temperature by using an ultrafast-pulsed x-ray source. The dynamics of carrier relaxation in a CZT single crystal is modeled at a microscopic level based on a multi-trapping effect. The effects of the irradiation flux and bias voltage on the amplitude and full width at half maximum(FWHM) of the transient currents are investigated. It is demonstrated that the temporal response process is affected by defect level occupation fraction. A fast photon current can be achieved under intense pulsed x-ray irradiation to be up to 2.78×10~9 photons mm-2·s-1. Meanwhile, it is found that high bias voltage could enhance carrier detrapping by suppressing the capture of structure defects and thus improve the temporal response of CZT detectors.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61901470 and U1931138)the Strategic Pioneer Program on Space Science,Chinese Academy of Sciences(Grant No.XDA15020501-04)+1 种基金the CAS“Light of West China”Program(Grant No.XAB2018A07)the Foundation of State Key Laboratory of China(Grant No.SKLIPR2021).
文摘Unstable mechanical structure,low energy efficiency,and cooling requirements limit the application of conventional x-ray tubes based on filament as cathode in several academic areas.In this paper,we demonstrate a light-controlled pulsed x-ray tube using multialkali cathode as electron generator.The photocathode active area of the light controlled x-ray tube is 13.2 cm^(2)(41 mm in diameter),which provides high photoelectron-emitting efficiency up to 0.288 mA/lm in 460-nm LED and 2.37-mA maximum tube current.Furthermore,the modulation ability from 1 kHz to 100 kHz of the x-ray tube is tested.The results suggest that the light-controlled pulsed x-ray tube has easy modulation and short x-ray pulse properties and is promising to be the next generation x-ray tube with wide applications in medical radiation therapy as well as the calibration for detectors and scintillators.
基金National Key Research and Development Program of China(2021YFB3700801)。
文摘Low-density short-duration pulsed current-assisted aging treatment was applied to the Ti-6Al-4V-0.5Mo-0.5Zr alloy subjected to different solution treatments.The results show that numerous α_(p) phases redissolve into the new β phase during the pulsed current-assisted aging process,and then the newly formed β phase is mainly transformed into the β_(t) phase,with occasional transition to new α_(p) phase,leading to a remarkable grain refinement,especially for the lamellarαs phases.In comparison to conventional aging treatment,the pulsed current-assisted aging approach achieves a significant enhancement in strength without degrading ductility,yielding an excellent mechanical property combination:a yield strength of 932 MPa,a tensile strength of 1042 MPa,and an elongation of 12.2%.It is primarily ascribed to the increased fraction of β_(t) phases,the obvious grain refinement effect,and the slip block effect induced by the multiple-variantαs colonies distributed within β_(t) phases.
基金financially supported by the Key Research and Development Program of Heilongjiang Province(No.2024ZXJ03C06)National Natural Science Foundation of China(No.52476192,No.52106237)+1 种基金Natural Science Foundation of Heilongjiang Province(No.YQ2022E027)Technology Project of China Datang Technology Innovation Co.,Ltd(No.DTKC-2024-20610).
文摘Pulsed dynamic electrolysis(PDE),driven by renewable energy,has emerged as an innovative electrocatalytic conversion method,demonstrating significant potential in addressing global energy challenges and promoting sustainable development.Despite significant progress in various electrochemical systems,the regulatory mechanisms of PDE in energy and mass transfer and the lifespan extension of electrolysis systems,particularly in water electrolysis(WE)for hydrogen production,remain insufficiently explored.Therefore,there is an urgent need for a deeper understanding of the unique contributions of PDE in mass transfer enhancement,microenvironment regulation,and hydrogen production optimization,aiming to achieve low-energy consumption,high catalytic activity,and long-term stability in the generation of target products.Here,this review critically examines the microenvironmental effects of PDE on energy and mass transfer,the electrode degradation mechanisms in the lifespan extension of electrolysis systems,and the key factors in enhancing WE for hydrogen production,providing a comprehensive summary of current research progress.The review focuses on the complex regulatory mechanisms of frequency,duty cycle,amplitude,and other factors in hydrogen evolution reaction(HER)performance within PDE strategies,revealing the interrelationships among them.Finally,the potential future directions and challenges for transitioning from laboratory studies to industrial applications are proposed.
基金supported by the Ministry of Science and Higher Education of the Russian Federation(agreement No.075-15-2021-1349)。
文摘Synchrotron method of resonant X-ray reflectivity 2D mapping has been applied to study ultrathin epitaxial layers of WS_(2)grown by pulsed laser deposition on Al_(2)O_(3)(0001)substrates.The measurements were carried out across the L absorption edge of tungsten to perform depth-dependent element-selective analysis sensitive to potential chemical modification of the WS_(2)layer in ambient conditions.Despite the few monolayer thickness of the studied film,the experimentally measured maps of reflectance as a function of incident angle and photon energy turned out to be quite informative showing well-pronounced interference effects near W absorption edge at 10210 eV.The synchrotron studies were complemented with conventional non-resonant reflectance measurements carried out in the laboratory at a fixed photon energy corresponding to Cu Kαemission.The reconstruction of the depth and energy dependent scattering length density within the studied multilayers was carried out using the OpenCL empowered fitting software utilizing spectral shaping algorithm which does not rely on the pre-measured reference absorption spectra.A thin WO_(x) layer has been revealed at the surface of the WS_(2)layer pointing out to the effect of water assisted photo-oxidation reported in a number of works related to ultrathin layers of transition metal dichalcogenides.
基金supported by the State Key Laboratory Foundation(Grant No.SKLIPR1212)
文摘Groups of a typical operational amplifier-μA741 were irradiated in a cobalt unit, each group accumulating a different total ionizing dose （TID）. The results showed that the TID caused power consumption current and slew rate （SR） to degenerate in ultra-linearity, owing to a severe reduction in the current gain of the internal LPNP transistors. Pulsed X-ray irradiation experiments were carried out on the μA741 groups with different values, and the results revealed that the impact on the response to the pulsed X-ray irradiation was greater when the devices absorbed more TID. The mechanism for this is explained on the basis of the circuit construction of the μA741; the sensitive parameters of the circuit were obtained via simulation on SP1CE. The simulation results additionally showed that if the sensitive parameters were optimized, the duration of interruption caused by the pulsed X-ray irradiation would be reduced significantly. In addition, several proposals are provided for hardening the devices.
基金supported by the Fundamental Research Funds for the Central Universities(No.FRF-BD-23-01).
文摘Non-metallic inclusions in steel are a significant challenge,affecting material properties and leading to issues such as stress concentration,cracking,and accelerated corrosion.Current methods for removing inclusions,including bubble,electromagnetic stirring,filtration separation,fluid flow,and sedimentation,often struggle with the removal of fine inclusions.Apart from these known methods,pulsed electric current(PEC),as an emerging technology,has demonstrated immense potential and environmental advantages.PEC offers adjustable current parameters and simple equipment,making it an attractive alternative to traditional methods.Its green energy-saving features and excellent results in regulating inclusion morphology and migration,as well as inhibiting submerged entry nozzle(SEN)clogging,make it a promising technology.In comparison to continuous current technology,PEC has shown significant advantages in regulating inclusions,not only improving purification efficiency but also demonstrating outstanding performance in flow stability and energy consumption.The ability of PEC to efficiently reduce inclusion numbers enhances the purity and quality of molten steel,improving its mechanical properties.Currently,the theoretical basis for controlling the movement of inclusions by current is mainly composed of three major theories:the double electric layer theory,electromagnetic force reverse separation theory,and electric free energy drive theory.These theories together form an important framework for researchers to understand and optimize the behavior of impurity movement controlled by electric current.Looking ahead,PEC is expected to pave the way for new solutions in directional regulation of inclusion migration,efficient inclusion removal,SEN clogging prevention,and the purification of molten steel.
基金supported by the Beijing Natural Science Foundation(No.QY24166).
文摘In a pulsed plasma thruster,the voltage distribution between the electrodes is a key factor that influences the ionization process.However,few researchers have conducted in-depth studies of this phenomenon in the past.Reported here are measurements of the voltage distribution between the plates of a parallel-plate pulsed plasma thruster under different discharge voltages,based on which the variations in the total circuit inductance and resistance as well as those between the plates are calculated.The results show that the time-averaged voltage across the plates accounts for 28.7%-50.4%of the capacitor voltage.As the capacitor initial voltage increases from 1250 V to 2000 V,the voltage across the plates rises,but its proportion relative to the capacitor voltage decreases.For every 250 V increase in the capacitor initial voltage,the average voltage proportion across the plates decreases by approximately 2%-3%.Additionally,the voltage proportion decreases gradually from the end near the propellant outward.The voltage distribution ratio between the plates is correlated with the proportions of the resistance and inductance between the plates relative to the total circuit.
基金National Natural Science Foundation of China(No.52476192,No.52106237)Natural Science Foundation of Heilongjiang Province(No.YQ2022E027)。
文摘The transition of hydrogen sourcing from carbon-intensive to water-based methodologies is underway,with renewable energy-powered proton exchange membrane water electrolysis(PEMWE)emerging as the preeminent pathway for hydrogen production.Despite remarkable advancements in this field,confronting the sluggish electrochemical kinetics and inherent high-energy consumption arising from deteriorated mass transport within PEMWE systems remains a formidable obstacle.This impediment stems primarily from the hindered protons mass transfer and the untimely hydrogen bubbles detachment.To address these challenges,we harness the inherent variability of electrical energy and introduce an innovative pulsed dynamic water electrolysis system.Compared to constant voltage electrolysis(hydrogen production rate:51.6 m L h^(-1),energy consumption:5.37 kWh Nm-^(3)H_(2)),this strategy(hydrogen production rate:66 m L h^(-1),energy consumption:3.83 kWh Nm-^(3)H_(2))increases the hydrogen production rate by approximately 27%and reduces the energy consumption by about 28%.Furthermore,we demonstrate the practicality of this system by integrating it with an off-grid photovoltaic(PV)system designed for outdoor operation,successfully driving a hydrogen production current of up to 500 mA under an average voltage of approximately 2 V.The combined results of in-situ characterization and finite element analysis reveal the performance enhancement mechanism:pulsed dynamic electrolysis(PDE)dramatically accelerates the enrichment of protons at the electrode/solution interface and facilitates the release of bubbles on the electrode surface.As such,PDE-enhanced PEMWE represents a synergistic advancement,concurrently enhancing both the hydrogen generation reaction and associated transport processes.This promising technology not only redefines the landscape of electrolysis-based hydrogen production but also holds immense potential for broadening its application across a diverse spectrum of electrocatalytic endeavors.
基金financially supported by the National Key Research and Development Program of China(Grant No.2022YFA1602700)the National Natural Science Foundation of China(Grant No.12274159)。
文摘Pulsed magnet technology is the only way to generate ultra-strong magnetic fields higher than 45 T so far.However,the inherently fast-changing field strength(typically on the order of 1000 T/s)poses significant challenges for spectroscopic measurements which rely on time integration of signals to improve spectral qualities.In this work,we report high-sensitivity spectroscopic measurements under pulsed high magnetic fields employing the long flat-top pulsed magnetic field technique.By means of a multiple-capacitor power supply,we were able to generate pulsed high magnetic fields with controllable flat-top pulse width and field stabilities.By synchronizing spectroscopic measurements with the waveform of the flattop magnetic field,the integration time of each spectrum can be increased by up to 100 times compared with that of the conventional spectroscopic measurements under pulsed magnetic fields,thus enabling high-sensitivity spectroscopic measurements under ultra-strong pulsed magnetic fields.These findings promise an efficient way to significantly improve the performance and extend the application of optical measurements under pulsed high magnetic fields.
文摘The accelerator-generating 6.13 MeV pulsed Gamma by 19F（p, αγ）160 reaction usually synchronizes with an intense bremsstrahlung x-ray which has a maximum energy of 1 MeV. This paper proposes a new method, named the scattering and absorbing method, to diagnose the 6.13 MeV Gamma. This method includes two parts： the detector and a scatterer placed in front of the detector. The detector converts the Gamma to electrons and then collects the electrons by a scintillator. In order to restrain the interference of the low-energy background, the scintillator collects the electrons at a small angle. The scintillator is wrapped with electro-absorbing material to absorb the low-energy electrons generated by background x-rays. The theoretical sensitivity ratio of 6.13 MeV Gamma to 1 MeV x-rays is greater than 150. The scatterer is a pretreatment tool to scatter some background x-rays away from the radial beam before they enter the detector. By varying the length, the scatterer can reduce the background x-rays to an acceptable level for the detector.
基金supported by the National Key R&D Program of China(2020YFA0714900,2023YFB3709903)the National Natural Science Foundation of China(U21B2082,52474410)+6 种基金the Key R&D Program of Shandong Province,China(2023CXGC010406)the Scientific Research Special Project for First-Class Disciplines in Inner Mongolia Autonomous Region(YLXKZX-NKD-001)the International Science and Technology Cooperation Project of Higher Education Institutions in Inner Mongolia Autonomous Region(GHXM-002)the Natural Science Foundation of Inner Mongolia Autonomous Region of China(2024ZD06)the Technology Support Project for the Construction of Major Innovation Platforms in Inner Mongolia Autonomous Region(XM2024XTGXQ16)the Beijing Municipal Natural Science Foundation(2222065)the Fundamental Research Funds for the Central Universities(FRF-TP-22-02C2).
文摘Traditional heat treatment methods require a significant amount of time and energy to affect atomic diffusion and enhance the spheroidization process of carbides in bearing steel,while pulsed current can accelerate atomic diffusion to achieve ultra-fast spheroidization of carbides.However,the understanding of the mechanism by which different pulse current parameters regulate the dissolution behavior of carbides requires a large amount of experimental data to support,which limits the application of pulse current technology in the field of heat treatment.Based on this,quantify the obtained pulse current processing data to create an important dataset that could be applied to machine learning.Through machine learning,the mechanism of mutual influence between carbide regulation and various factors was elucidated,and the optimal spheroidization process parameters were determined.Compared to the 20 h required for traditional heat treatment,the application of pulsed electric current technology achieved ultra-fast spheroidization of GCr15 bearing steel within 90 min.
基金supported by the Natural Science Foundation of China(Nos.U23B20151 and 52171253).
文摘Shielding materials are critical for downhole pulsed neutron tool design because they directly influence the accuracy of formation measurements.A well-designed shield configuration ensures that the response of the tool is maximally representative of the formation without being affected by the tool and borehole environment.This study investigated the effects of boron-containing materials on neutron and gamma detectors based on a newly designed logging-while-drilling tool that is currently undergoing manufacturing.As the boron content increased,the ability to absorb thermal neutrons increased significantly.Through simulation,it was proven that boron carbide(B_(4)C)can be used as an effective boron shielding material for thermal neutrons,and is therefore employed in this work.To shield against thermal neutrons migrating from the mud pipes,the optimal shielding thicknesses for the near-and far-neutron detectors were determined to be 5 and 4 mm.At a porosity of 25 p.u.,near-neutron sensitivity exhibited a 5.6%increase.Furthermore,to shield the capture gamma generated by thermal neutrons once they enter the tool from the mud pipe and formation,internal and external shields for the gamma detector were evaluated.The results show that the internal shield requires a boron content of 75%,whereas the external shield has a thickness of 14.2 mm thickness and a boron content of 25%to minimize the tool effect.
基金Fundamental Research Funds for the Central Universities(M23JBZY00050)National Natural Science Foundation of China(22278032)。
文摘The kinetic characteristics of plasma-assisted oxidative pyrolysis of ammonia are studied by using the global/fluid models hybrid solution method.Firstly,the stable products of plasma-assisted oxidative pyrolysis of ammonia are measured.The results show that the consumption of NH_(3)/O_(2)and the production of N_(2)/H_(2)change linearly with the increase of voltage,which indicates the decoupling of nonequilibrium molecular excitation and oxidative pyrolysis of ammonia at low temperatures.Secondly,the detailed reaction kinetics mechanism of ammonia oxidative pyrolysis stimulated by a nanosecond pulse voltage at low pressure and room temperature is established.Based on the reaction path analysis,the simplified mechanism is obtained.The detailed and simplified mechanism simulation results are compared with experimental data to verify the accuracy of the simplified mechanism.Finally,based on the simplified mechanism,the fluid model of ammonia oxidative pyrolysis stimulated by the nanosecond pulse plasma is established to study the pre-sheath/sheath behavior and the resultant consumption and formation of key species.The results show that the generation,development,and propagation of the pre-sheath have a great influence on the formation and consumption of species.The consumption of NH_(3)by the cathode pre-sheath is greater than that by the anode pre-sheath,but the opposite is true for OH and O(1S).However,within the sheath,almost all reactions do not occur.Further,by changing the parameters of nanosecond pulse power supply voltage,it is found that the electron number density,electron current density,and applied peak voltages are not the direct reasons for the structural changes of the sheath and pre-sheath.Furthermore,the discharge interval has little effect on the sheath structure and gas mixture breakdown.The research results of this paper not only help to understand the kinetic promotion of non-equilibrium excitation in the process of oxidative pyrolysis but also help to explore the influence of transport and chemical reaction kinetics on the oxidative pyrolysis of ammonia.
基金Project supported by the National Key R&D Program of China(Grant No.2022YFA1402404)the National Natural Science Foundation of China(Grant Nos.T2394473,624B2070,and 62274085)。
文摘Type-II Dirac semimetal PtTe2is a promising candidate for various electronic device applications due to its high carrier mobility,high conductivity,and air stability.In this work,we report on the growth of large-scale PtTe_(2)films by the pulsed laser deposition(PLD)and the comparison of the magnetotransport properties with the PtTe2films grown by the chemical vapor deposition(CVD).The low-temperature Hall curves of the PLD-grown films exhibit a linear behavior,in contrast with the nonlinear characteristic of the Hall behavior observed in CVD-grown films,in which a defect gradient is introduced.Meanwhile,both PtTe2films show weak antilocalization at low temperatures,which is attributed to the strong spin–orbit coupling.
基金supported by the National Natural Science Foundation of China(Nos.U21A20399 and 52274407)Liaoning Province Applied Basic Research Program(No.2022JH2/101300212).
文摘In this work,we aim to develop a novel post-treatment process combining cryogenic and pulsed electric field treatment to enhance WC-Co cemented carbides.The results show a 15.62%increase in hardness from 1831.38 to 2117.38 HV30,a 9.60%rise in fracture toughness from 9.06 to 9.93 MPa·m^(1/2),while the friction coefficient decreases from 0.63 to 0.47.Through the residual stress evolution,WC orientation change and the martensitic transformation of Co,and the internal enhancement mechanism of cryogenic combined with pulsed electric field treatment are revealed.The electron wind generated by the pulsed electric field can efficiently reduce the residual stress induced by cryogenic process.The evolution of residual stress promotes the base slip of WC,increasing the degree of{0001}orientation.In addition,the degree of martensitic transformation of Co intensifies,with the hcp-Co/fcc-Co ratio rising from 0.41%to 17.86%.The enhanced WC{0001}orientation and increased hcp-Co content contribute to significant improvements in hardness and wear resistance.This work provides a novel efficient enhancement strategy for ceramics and alloys,with the potential to be a mainstream strengthening method in the future.
基金supported by the National Key R&D Program of China(No.2021YFB2801600)the National Natural Science Foundation of China(Nos.52072060,52202164 and 52021001)the Natural Science Foundation of Sichuan(Nos.2023NSFSC1950 and 2022NSFSC1990).
文摘The complicated structure of electronic devices makes the conventional annealing method,which involves placing the entire device in a furnace,insufficient for achieving the desired quality.This issue is currently addressed through the use of pulsed laser annealing,where a specific target layer is heated,preventing the overheating of other layers or the substrate.However,this method is only applicable to a very limited range of materials and requires very expensive,powerful pulsed laser sources.Herein,a novel approach for the selective local thermal treatment of thin films is proposed;in this method,short,powerful current pulses are applied to the target conductive layer.The application of two current pulses with a length of 1.5 s induced the crystallization of a 160-nm thick indium tin oxide(ITO)film,resulting in a sheet resistance of 8.68Ω·sq^(-1),an average visible light transmittance of 86.69%,and a figure of merit(FoM)of 293.61.This FoM is an order of magnitude higher than that of the as-prepared ITO film,and to the best of our knowledge,is among the highest reported values for the polycrystalline ITO films.Simulations have shown that even faster and more localized crystallization could be achieved by increasing the power of pulsed current.This novel annealing method is applicable to most semi-conductive or metallic thin films and requires only a relatively inexpensive pulsed current source,making it potentially more attractive than pulsed laser annealing.
基金Supported by Guangdong Major Project of Basic and Applied Research,China(Grant No.2019B030302010)National Natural Science Foundation of China (Grant Nos.51735003,52205456)
文摘Avoiding crystallization while maintaining the original microstructure and mechanical properties of the material are long-term goals of laser welding of Zr-based bulk metallic glass(BMG).In this paper,the effect of pulsed laser welding parameters on the microstructure,crystallization degree,and mechanical properties of Zr57Nb5Cu15.4Ni12.6Al10 BMG is investigated.Non-crystallized welding forming of a zirconium-based amorphous alloy is achieved by optimizing the process parameters of pulsed laser welding.The crystallization degree of Zr-based BMG is mainly determined by the welding speed and power.The welding depth and crystallization area fraction increase with an increase in the effective peak power density.The optimized welding process can effectively reduce the heat accumulation of the weld,thus avoiding crystallization.The flexural strength of the weld can be maintained at 96.5%of the matrix.
