In order to quickly and accurately evaluate gas well deliverability,it is necessary to clarify the applicable conditions of the simplified laminarinertial-turbulent gas well deliverability evaluation method(i.e.,press...In order to quickly and accurately evaluate gas well deliverability,it is necessary to clarify the applicable conditions of the simplified laminarinertial-turbulent gas well deliverability evaluation method(i.e.,pressure-squared method and pressure method).In this regard,this paper analyzes the PVT data,simulation wells and field case wells of typical gas reservoirs in China by reviewing the formal evolution of the flow control equation for the real gases in porous media.Then,the applicable conditions of binomial pressure-squared method and pressure method are discussed.And the following research results were obtained.First,when the pressure is lower than 14 MPa,p/(μZ) is basically a constant;and when the pressure is higher than 42 MPa,μZ is basically a constant.Second,the applicable range of the pressure-squared method can be increased from 14 to 20 MPa.In this case,the relative error of absolute open flow potential calculated using the pressure-squared method is less than 5%compared with the pseudo-pressure method.If the pressure is between 20 and 30 MPa,the relative error of the absolute open flow potential calculated using the pressure-squared method is less than 10%.Third,when the pressure exceeds 80 MPa,the relative error of the absolute open flow potential calculated using the pressure method is less than 10%compared with the pseudo-pressure method.If the pressure-squared method is used in the case of high pressure,the calculated absolute open flow potential is lower and the relative error is close to 25%.Fourth,in the case of low pressure,if the pressure is constant,the higher the temperature is,the smaller the relative error between the pressure-squared method and the pseudo-pressure method is.In the case of high pressure,if the pressure is constant,the higher the temperature is,the greater the relative error between the pressure method and the pseudo-pressure method.In conclusion,it is recommended to adopt the pseudo-pressure method in laminareinertial-turbulent gas well deliverability analysis.In the case of low pressure(below 30 MPa),the pressure-squared method can be used.In the case of high pressure(above 80 MPa),the pressure method can be applied.展开更多
The Chinese fir wood was impregnated using a cyclic increasingpressure method(CIPM)with phenolic prepolymers as the impregnating modifier.Unmodified Chinese fir and progressive increasing-pressure method(PIPM)impregna...The Chinese fir wood was impregnated using a cyclic increasingpressure method(CIPM)with phenolic prepolymers as the impregnating modifier.Unmodified Chinese fir and progressive increasing-pressure method(PIPM)impregnated Chinese fir were used as reference samples and were compared and analyzed.The product’s chemical structure,internal morphology,crystal structure,and heat resistance were characterized.The transversal and longitudinal sections showed better filling effects,so that it bore greater external loading and reduced the water storage space.CIPM infused more phenolic prepolymer into the Chinese fir.Not only producing more physical filling but also forming more hydrogen bond associations and chemical bond combinations.Compared with PIPM and unmodi-fied Chinese fir,the CIPM impregnated Chinese fir had better mechanical strength and water resistance.The cellulose chains in CIPM impregnated Chinese fir were more closely linked and their crystallinity were clearly improved.Changes in internal morphology and crystal structure explained the reason why the mechanical properties and water resistance of CIPM impregnated Chinese fir were improved significantly.This Chinese fir had lower thermal decomposition rates,higher decomposition residual rates,and smaller combustion flames,which confirmed that it possessed improved heat and fire resistance.展开更多
In studying the diffusion-controlled adsorption kinetics of aqueous surfactant solutions at the air/solution surface by means of the maximal bubble pressure method, Fick's diffusion equation for a sphere should be...In studying the diffusion-controlled adsorption kinetics of aqueous surfactant solutions at the air/solution surface by means of the maximal bubble pressure method, Fick's diffusion equation for a sphere should be used. In this paper the equation was solved by means of Laplace transformation under different initial and boundary conditions. The dynamic surface adsorption F(t) for a surfactant solution, which was used to describe the diffusion-controlled adsorption kinetics at the solution surface, was derived. Different from the planar surface adsorption, the dynamic surface adsorption F(t) for the short time consists of two terms: one is the same as Ward-Tordai equation and the other reflects the geometric effect caused by the spherical bubble surface. This effect should not be neglected for the very small radius of the capillary. The equilibrium surface tension γeq and the dynamic surface tension γ(t) of aqueous C10E6 [CH3(CH2)9(OCH2CH2)6OH] solution at temperature 25℃ were measuredby means of Wilhelmy plate method and maximal bubble pressure method respectively. As t→ 0, the theoreticalanalysis is in good agreement with experimental results and the dependence of γ(t) on is linear.展开更多
Gas holdup is one of the key parameters in flotation process. Gas holdup as measured by a differential pressure method was investigated and the relative errors compared to the average gas holdup from the volume expans...Gas holdup is one of the key parameters in flotation process. Gas holdup as measured by a differential pressure method was investigated and the relative errors compared to the average gas holdup from the volume expansion method. The errors were used to establish optimum measurement positions. The results show that the measurement position should be in the middle of the column and in the region half way from the center to the wall (the half-radius). The gas holdup along the axial direction is lower at the bottom and higher at the top of the floatation column. The gas holdup along the radial direction is lower near the wall and higher near the center of the flotation column. The average gas holdup measure- ment can be replaced by regional gas holdup values.展开更多
The cut-off negative pressure method is one of effective approaches to solve the seepage flow with free surface. According to the characteristics of this method, however, it has been found out that the deficiency of t...The cut-off negative pressure method is one of effective approaches to solve the seepage flow with free surface. According to the characteristics of this method, however, it has been found out that the deficiency of the algorithms is to easily cause inaccurate simulation in the vicinity of free surface owing to the penalty function with only one controlling penalty parameter. Therefore, an improved cut-off pressure method was presented by constructing penalty function with two controlling penalty parameters. The improved algorithms were illustrated to be able to improve the simulation accuracy and raise the convergence speed through considering the effects of the partially saturated or unsaturated elements more reasonably and calculating the nodal external forces more accurately. Finally, the improved cut-off negative pressure method was applied to the simulation of unsteady seepage flow with free surface, and the corresponding program codes were developed with validation of some cases.展开更多
An improved finite difference method （FDM）is described to solve existing problems such as low efficiency and poor convergence performance in the traditional method adopted to derive the pressure distribution of aero...An improved finite difference method （FDM）is described to solve existing problems such as low efficiency and poor convergence performance in the traditional method adopted to derive the pressure distribution of aerostatic bearings. A detailed theoretical analysis of the pressure distribution of the orifice-compensated aerostatic journal bearing is presented. The nonlinear dimensionless Reynolds equation of the aerostatic journal bearing is solved by the finite difference method. Based on the principle of flow equilibrium, a new iterative algorithm named the variable step size successive approximation method is presented to adjust the pressure at the orifice in the iterative process and enhance the efficiency and convergence performance of the algorithm. A general program is developed to analyze the pressure distribution of the aerostatic journal bearing by Matlab tool. The results show that the improved finite difference method is highly effective, reliable, stable, and convergent. Even when very thin gas film thicknesses （less than 2 Win）are considered, the improved calculation method still yields a result and converges fast.展开更多
The plane strain asymmetrical rolling was analyzed using slab method. The contact arc was replaced by parabola, and the constant surface friction status was adopted during the analysis. The deformation area was divide...The plane strain asymmetrical rolling was analyzed using slab method. The contact arc was replaced by parabola, and the constant surface friction status was adopted during the analysis. The deformation area was divided into three zones according to the direction of the friction. Then, the three zones were studied, respectively. A rolling force model and a rolling torque model were developed based on the analysis, and they were used to analyze the influ- ence of asymmetrical rolling factors on deformation area and unit pressure if they had good precision which was determined by comparing the calculated results with the measured ones.展开更多
Stabilizing pile is a kind of earth shoring structure frequently used in slope engineering. When the piles have cantilever segments above the ground,laggings are usually installed to avoid collapse of soil between pil...Stabilizing pile is a kind of earth shoring structure frequently used in slope engineering. When the piles have cantilever segments above the ground,laggings are usually installed to avoid collapse of soil between piles. Evaluating the earth pressure acting on laggings is of great importance in design process.Since laggings are usually less stiff than piles,the lateral pressure on lagging is much closer to active earth pressure. In order to estimate the lateral earth pressure on lagging more accurately,first,a model test of cantilever stabilizing pile and lagging systems was carried out. Then,basing the experimental results a three-dimensional sliding wedge model was established. Last,the calculation process of the total active force on lagging is presented based on the kinematic approach of limit analysis. A comparison is made between the total active force on lagging calculated by the formula presented in this study and the force on a same-size rigid retaining wall obtained from Rankine's theory. It is found that the proposed method fits well with the experimental results.Parametric studies show that the total active force on lagging increases with the growth of the lagging height and the lagging clear span; while decreases asthe soil internal friction angle and soil cohesion increase.展开更多
Application of pressured grouting method (PGM) in pile engineering can tackle problems encountered during construction of bored piles. Bearing capacity of piles can be increased through compaction of subsoils around p...Application of pressured grouting method (PGM) in pile engineering can tackle problems encountered during construction of bored piles. Bearing capacity of piles can be increased through compaction of subsoils around piles. This paper reports research efforts of this technique by the pile research team in Southwest Jiaotong University in last decade with respect to the construction process, test findings, and primary research conclusions. The social-economical benefits of this method and application market in pile engineering are also analyzed.展开更多
An in-situ TiCp/Al composite was prepared by a thermal explosion/quick pressure method （TE/QP）. The effect of Al content on the reaction temperature as well as the reaction rate has been studied. Phase constituents ...An in-situ TiCp/Al composite was prepared by a thermal explosion/quick pressure method （TE/QP）. The effect of Al content on the reaction temperature as well as the reaction rate has been studied. Phase constituents and the microstructure of the composites and the particle size of the reinforcement were analysed using X-ray diffraction （XRD） and scanning electron microscopy （SEM）. The results have shown that TiCp/Al composite with 40～70 vol. pct TiC particle reinforcement and high relative density can be directly obtained by TE/QP. TiC is the only reaction product when Al content in Al-Ti-C system is no more than 60 vol. pct, but Al3Ti phase will also form when Al content is more than 60 vol. pct. Increasing Al content prolongs the initial reaction time, reduces the highest reaction temperature and the reaction rate, and decreases the size of TiC particles. In addition, the microstructure of TiCp/Al composite and the structure of interface between TiCp and Al are studied using SEM and transmission electron microscopy （TEM）. The results show that the in-situ synthesized TiC particle has fcc cubic structure. The orientation between TiC particles and Al matrix can be described as （220）Al//（022）TiC and [112]Al//[011]TiC. Results of the mechanical property tests reveal that the ultimate strength （σ） and modulus （E） are 687 MPa and 142 GPa respectively when the Al content is 40 vol. pct. On contrary, 6 elongation increases by 3.2% with increasing Al content.展开更多
There is a need for determinations of soil organic carbon (SOC) and inorganic carbon (SIC) due to increasing interest in soil carbon sequestration. Two sets of soil samples were collected separately from the Yanqi Bas...There is a need for determinations of soil organic carbon (SOC) and inorganic carbon (SIC) due to increasing interest in soil carbon sequestration. Two sets of soil samples were collected separately from the Yanqi Basin of northwest China to evaluate loss-on-ignition (LOI) method for estimating SOC and SIC in arid soils through determining SOC using an element analyzer, a modified Walkley-Black method and a LOI method with combustion at 375℃ for 17 h and determining SIC using a pressure calcimeter method and a LOI procedure estimated by a weight loss between 375 to 800℃. Our results indicated that the Walkley-Black method provided 99%recovery of SOC for the arid soils tested. There were strong linear relationships(r > 0.93, P < 0.001) for both SOC and SIC between the traditional method and the LOI technique. One set of soil samples was used to develop relationships between LOI and SOC(by the Walkley-Black method), and between LOI and SIC(by the pressure calcimeter method), and the other set of soil samples was used to evaluate the derived equations by comparing predicted SOC and SIC with measured values. The mean absolute errors were small for both SOC (1.7 g C kg-1) and SIC(1.22 g C kg-1), demonstrating that the LOI method was reliable and could provide accurate estimates of SOC and SIC for arid soils.展开更多
A unified analysis is presented for the stabilized methods including the pres- sure projection method and the pressure gradient local projection method of conforming and nonconforming low-order mixed finite elements f...A unified analysis is presented for the stabilized methods including the pres- sure projection method and the pressure gradient local projection method of conforming and nonconforming low-order mixed finite elements for the stationary Navier-Stokes equa- tions. The existence and uniqueness of the solution and the optimal error estimates are proved.展开更多
A pressure gradient discontinuous finite element formulation for the compressible Navier-Stokes equations is derived based on local projections. The resulting finite element formulation is stable and uniquely solvable...A pressure gradient discontinuous finite element formulation for the compressible Navier-Stokes equations is derived based on local projections. The resulting finite element formulation is stable and uniquely solvable without requiring a B-B stability condition. An error estimate is Obtained.展开更多
Basis of explosion's responsive analysis and anti-explosion's structure design is the relation among thin explosive mass, impulse and plate deformation. In this paper, the limitations of theoretical calculatio...Basis of explosion's responsive analysis and anti-explosion's structure design is the relation among thin explosive mass, impulse and plate deformation. In this paper, the limitations of theoretical calculation and experimental methods are analyzed according to the relation between impulse loading and deformation of steel plate in thin explosive experiment. The time histories of deformation for the square steel plate under the impulse of thin explosive are calculated by the fluid-solid coupling method and the pressure loading method. The advantages of the pressure loading method and the fluid-solid coupling method are compared. The results show that the steel plate deformation can be estimated accurately using the fluid-solid coupling method when the explosive impulse is unknown, while the theoretical calculation and the pressure loading method provide quick and accurate prediction on the steel plate deformation when the explosive impulse is known.展开更多
For transient Naiver-Stokes problems, a stabilized nonconforming finite element method is presented, focusing on two pairs inf-sup unstable finite element spaces, i.e., pNC/pNC triangular and pNQ/pNQ quadrilateral fin...For transient Naiver-Stokes problems, a stabilized nonconforming finite element method is presented, focusing on two pairs inf-sup unstable finite element spaces, i.e., pNC/pNC triangular and pNQ/pNQ quadrilateral finite element spaces. The semi- and full-discrete schemes of the stabilized method are studied based on the pressure projection and a variational multi-scale method. It has some attractive features： avoiding higher-order derivatives and edge-based data structures, adding a discrete velocity term only on the fine scale, being effective for high Reynolds number fluid flows, and avoiding increased computation cost. For the full-discrete scheme, it has second-order estimations of time and is unconditionally stable. The presented numerical results agree well with the theoretical results.展开更多
Plasma synthetic jet actuator（PSJA） has a wide application prospect in the high-speed flow control field for its high jet velocity.In this paper,the influence of the air pressure on the performance of a two-electrod...Plasma synthetic jet actuator（PSJA） has a wide application prospect in the high-speed flow control field for its high jet velocity.In this paper,the influence of the air pressure on the performance of a two-electrode PSJA is investigated by the schlieren method in a large range from 7 k Pa to 100 k Pa.The energy consumed by the PSJA is roughly the same for all the pressure levels.Traces of the precursor shock wave velocity and the jet front velocity vary a lot for different pressures.The precursor shock wave velocity first decreases gradually and then remains at 345 m/s as the air pressure increases.The peak jet front velocity always appears at the first appearance of a jet,and it decreases gradually with the increase of the air pressure.A maximum precursor shock wave velocity of 520 m/s and a maximum jet front velocity of 440 m/s are observed at the pressure of 7 k Pa.The averaged jet velocity in one period ranges from 44 m/s to 54 m/s for all air pressures,and it drops with the rising of the air pressure.High velocities of the precursor shock wave and the jet front indicate that this type of PSJA can still be used to influence the high-speed flow field at 7 k Pa.展开更多
The precise managed pressure drilling(MPD)technology is mainly used to deal with the difficulties encountered when oil and gas open hole sections with multiple pressure systems and the strata with narrow safety densit...The precise managed pressure drilling(MPD)technology is mainly used to deal with the difficulties encountered when oil and gas open hole sections with multiple pressure systems and the strata with narrow safety density window are drilled through.If its liner cementing is carried out according to the conventional method,lost circulation is inevitable in the process of cementing while the displacement efficiency of smallclearance liner cementing is satisfied.If the positive and inverse injection technology is adopted,the cementing quality cannot meet the requirements of later well test engineering of ultradeep wells.In this paper,the cementing operation ofØ114.3 mm liner in Well Longgang 70 which was drilled in the Jiange structure of the Sichuan Basin was taken as an example to explore the application of the cementing technology based on the precise MPD and pressure balancing method to the cementing of long open-hole sections(as long as 859 m)with both high and low pressures running through multiple reservoirs.On the one hand,the technical measures were taken specifically to ensure the annulus filling efficiency of slurry and the pressure balance in the whole process of cementing.And on the other hand,the annulus pressure balance was precisely controlled by virtue of precise MPD devices and by injecting heavy weight drilling fluids through central pipes,and thus the wellbore pressure was kept steady in the whole process of cementing in the strata with narrow safety density window.It is indicated thatØ114.3 mm liner cementing in this well is good with qualified pressure tests and no channeling emerges at a funnel during the staged density reduction.It is concluded that this method can enhance the liner cementing quality of complex ultradeep gas wells and improve the wellbore conditions for the later safe well tests of high-pressure gas wells.展开更多
An active measurement method and its principle was introduced consideringthe low success rate,special difficulty,and long measurement time of the direct gas pressuremeasurement currently used in coal roadways.The tech...An active measurement method and its principle was introduced consideringthe low success rate,special difficulty,and long measurement time of the direct gas pressuremeasurement currently used in coal roadways.The technology of drilling,boreholesealing depth,borehole sealing length,sealing control of the measuring process,compensatorycomputation of gas loss quantity and other key techniques were discussed.Finally,based on the latest instrument the authors developed,a series of experiments of directgas pressure measurement in the coal roadways of the Jincheng and Tongchuanmine district,were carried out.The experimental results show that active gas pressuremeasurement technique has advantages as follows:(1) the application scope of direct gaspressure measurement technique is wide and it does not have the restriction of coalhardness,coal seam fissure and other conditions;(2) the measured results are credible,which can be tested by the same gas pressure value acquired from a different borehole inthe same place;(3) the measurement process is convenient and quick,it takes about 2 to3 days to acquire the gas pressure value in a coal seam.展开更多
基金Project supported by Major Science&Technology Project of PetroChina Company Limited“Research and application of key technologies for development of deepeultra-deep gas reservoirs in Kuqa Depression”(No.:2018E-1803).
文摘In order to quickly and accurately evaluate gas well deliverability,it is necessary to clarify the applicable conditions of the simplified laminarinertial-turbulent gas well deliverability evaluation method(i.e.,pressure-squared method and pressure method).In this regard,this paper analyzes the PVT data,simulation wells and field case wells of typical gas reservoirs in China by reviewing the formal evolution of the flow control equation for the real gases in porous media.Then,the applicable conditions of binomial pressure-squared method and pressure method are discussed.And the following research results were obtained.First,when the pressure is lower than 14 MPa,p/(μZ) is basically a constant;and when the pressure is higher than 42 MPa,μZ is basically a constant.Second,the applicable range of the pressure-squared method can be increased from 14 to 20 MPa.In this case,the relative error of absolute open flow potential calculated using the pressure-squared method is less than 5%compared with the pseudo-pressure method.If the pressure is between 20 and 30 MPa,the relative error of the absolute open flow potential calculated using the pressure-squared method is less than 10%.Third,when the pressure exceeds 80 MPa,the relative error of the absolute open flow potential calculated using the pressure method is less than 10%compared with the pseudo-pressure method.If the pressure-squared method is used in the case of high pressure,the calculated absolute open flow potential is lower and the relative error is close to 25%.Fourth,in the case of low pressure,if the pressure is constant,the higher the temperature is,the smaller the relative error between the pressure-squared method and the pseudo-pressure method is.In the case of high pressure,if the pressure is constant,the higher the temperature is,the greater the relative error between the pressure method and the pseudo-pressure method.In conclusion,it is recommended to adopt the pseudo-pressure method in laminareinertial-turbulent gas well deliverability analysis.In the case of low pressure(below 30 MPa),the pressure-squared method can be used.In the case of high pressure(above 80 MPa),the pressure method can be applied.
基金This work was financially supported by Hunan Provincial Technical Innovation Platform and Talent Program in Science and Technology,China(2019RS2040)the National Natural Science Foundation of China(31770606)Major Science and Technology Program of Hunan Province,PR China(2017NK1010).
文摘The Chinese fir wood was impregnated using a cyclic increasingpressure method(CIPM)with phenolic prepolymers as the impregnating modifier.Unmodified Chinese fir and progressive increasing-pressure method(PIPM)impregnated Chinese fir were used as reference samples and were compared and analyzed.The product’s chemical structure,internal morphology,crystal structure,and heat resistance were characterized.The transversal and longitudinal sections showed better filling effects,so that it bore greater external loading and reduced the water storage space.CIPM infused more phenolic prepolymer into the Chinese fir.Not only producing more physical filling but also forming more hydrogen bond associations and chemical bond combinations.Compared with PIPM and unmodi-fied Chinese fir,the CIPM impregnated Chinese fir had better mechanical strength and water resistance.The cellulose chains in CIPM impregnated Chinese fir were more closely linked and their crystallinity were clearly improved.Changes in internal morphology and crystal structure explained the reason why the mechanical properties and water resistance of CIPM impregnated Chinese fir were improved significantly.This Chinese fir had lower thermal decomposition rates,higher decomposition residual rates,and smaller combustion flames,which confirmed that it possessed improved heat and fire resistance.
基金Supported by the Scientific Research Foundation of the State Education Ministry for the Returned Overseas Chinese Scholars (D4200111).
文摘In studying the diffusion-controlled adsorption kinetics of aqueous surfactant solutions at the air/solution surface by means of the maximal bubble pressure method, Fick's diffusion equation for a sphere should be used. In this paper the equation was solved by means of Laplace transformation under different initial and boundary conditions. The dynamic surface adsorption F(t) for a surfactant solution, which was used to describe the diffusion-controlled adsorption kinetics at the solution surface, was derived. Different from the planar surface adsorption, the dynamic surface adsorption F(t) for the short time consists of two terms: one is the same as Ward-Tordai equation and the other reflects the geometric effect caused by the spherical bubble surface. This effect should not be neglected for the very small radius of the capillary. The equilibrium surface tension γeq and the dynamic surface tension γ(t) of aqueous C10E6 [CH3(CH2)9(OCH2CH2)6OH] solution at temperature 25℃ were measuredby means of Wilhelmy plate method and maximal bubble pressure method respectively. As t→ 0, the theoreticalanalysis is in good agreement with experimental results and the dependence of γ(t) on is linear.
基金supports for this work provided by the NationalKey Technology R&D Program in the 11th Five-Year Plan of China(No. 2008BAB31B03)
文摘Gas holdup is one of the key parameters in flotation process. Gas holdup as measured by a differential pressure method was investigated and the relative errors compared to the average gas holdup from the volume expansion method. The errors were used to establish optimum measurement positions. The results show that the measurement position should be in the middle of the column and in the region half way from the center to the wall (the half-radius). The gas holdup along the axial direction is lower at the bottom and higher at the top of the floatation column. The gas holdup along the radial direction is lower near the wall and higher near the center of the flotation column. The average gas holdup measure- ment can be replaced by regional gas holdup values.
文摘The cut-off negative pressure method is one of effective approaches to solve the seepage flow with free surface. According to the characteristics of this method, however, it has been found out that the deficiency of the algorithms is to easily cause inaccurate simulation in the vicinity of free surface owing to the penalty function with only one controlling penalty parameter. Therefore, an improved cut-off pressure method was presented by constructing penalty function with two controlling penalty parameters. The improved algorithms were illustrated to be able to improve the simulation accuracy and raise the convergence speed through considering the effects of the partially saturated or unsaturated elements more reasonably and calculating the nodal external forces more accurately. Finally, the improved cut-off negative pressure method was applied to the simulation of unsteady seepage flow with free surface, and the corresponding program codes were developed with validation of some cases.
基金The National Natural Science Foundation of China(No50475073,50775036)the High Technology Research Program of Jiangsu Province(NoBG2006035)
文摘An improved finite difference method （FDM）is described to solve existing problems such as low efficiency and poor convergence performance in the traditional method adopted to derive the pressure distribution of aerostatic bearings. A detailed theoretical analysis of the pressure distribution of the orifice-compensated aerostatic journal bearing is presented. The nonlinear dimensionless Reynolds equation of the aerostatic journal bearing is solved by the finite difference method. Based on the principle of flow equilibrium, a new iterative algorithm named the variable step size successive approximation method is presented to adjust the pressure at the orifice in the iterative process and enhance the efficiency and convergence performance of the algorithm. A general program is developed to analyze the pressure distribution of the aerostatic journal bearing by Matlab tool. The results show that the improved finite difference method is highly effective, reliable, stable, and convergent. Even when very thin gas film thicknesses （less than 2 Win）are considered, the improved calculation method still yields a result and converges fast.
基金Item Sponsored by National Natural Science Foundation of China (50104006)National Key Technology Research and Development Program of China(2006BAE03A08)
文摘The plane strain asymmetrical rolling was analyzed using slab method. The contact arc was replaced by parabola, and the constant surface friction status was adopted during the analysis. The deformation area was divided into three zones according to the direction of the friction. Then, the three zones were studied, respectively. A rolling force model and a rolling torque model were developed based on the analysis, and they were used to analyze the influ- ence of asymmetrical rolling factors on deformation area and unit pressure if they had good precision which was determined by comparing the calculated results with the measured ones.
基金financially supported by the National Key Technology Research and Development Program of the Ministry of Science and Technology of China under Grant No. 2012BAJ22B06
文摘Stabilizing pile is a kind of earth shoring structure frequently used in slope engineering. When the piles have cantilever segments above the ground,laggings are usually installed to avoid collapse of soil between piles. Evaluating the earth pressure acting on laggings is of great importance in design process.Since laggings are usually less stiff than piles,the lateral pressure on lagging is much closer to active earth pressure. In order to estimate the lateral earth pressure on lagging more accurately,first,a model test of cantilever stabilizing pile and lagging systems was carried out. Then,basing the experimental results a three-dimensional sliding wedge model was established. Last,the calculation process of the total active force on lagging is presented based on the kinematic approach of limit analysis. A comparison is made between the total active force on lagging calculated by the formula presented in this study and the force on a same-size rigid retaining wall obtained from Rankine's theory. It is found that the proposed method fits well with the experimental results.Parametric studies show that the total active force on lagging increases with the growth of the lagging height and the lagging clear span; while decreases asthe soil internal friction angle and soil cohesion increase.
文摘Application of pressured grouting method (PGM) in pile engineering can tackle problems encountered during construction of bored piles. Bearing capacity of piles can be increased through compaction of subsoils around piles. This paper reports research efforts of this technique by the pile research team in Southwest Jiaotong University in last decade with respect to the construction process, test findings, and primary research conclusions. The social-economical benefits of this method and application market in pile engineering are also analyzed.
文摘An in-situ TiCp/Al composite was prepared by a thermal explosion/quick pressure method （TE/QP）. The effect of Al content on the reaction temperature as well as the reaction rate has been studied. Phase constituents and the microstructure of the composites and the particle size of the reinforcement were analysed using X-ray diffraction （XRD） and scanning electron microscopy （SEM）. The results have shown that TiCp/Al composite with 40～70 vol. pct TiC particle reinforcement and high relative density can be directly obtained by TE/QP. TiC is the only reaction product when Al content in Al-Ti-C system is no more than 60 vol. pct, but Al3Ti phase will also form when Al content is more than 60 vol. pct. Increasing Al content prolongs the initial reaction time, reduces the highest reaction temperature and the reaction rate, and decreases the size of TiC particles. In addition, the microstructure of TiCp/Al composite and the structure of interface between TiCp and Al are studied using SEM and transmission electron microscopy （TEM）. The results show that the in-situ synthesized TiC particle has fcc cubic structure. The orientation between TiC particles and Al matrix can be described as （220）Al//（022）TiC and [112]Al//[011]TiC. Results of the mechanical property tests reveal that the ultimate strength （σ） and modulus （E） are 687 MPa and 142 GPa respectively when the Al content is 40 vol. pct. On contrary, 6 elongation increases by 3.2% with increasing Al content.
基金Supported by the "Hundred Talents Program" of the Chinese Academy of Sciences
文摘There is a need for determinations of soil organic carbon (SOC) and inorganic carbon (SIC) due to increasing interest in soil carbon sequestration. Two sets of soil samples were collected separately from the Yanqi Basin of northwest China to evaluate loss-on-ignition (LOI) method for estimating SOC and SIC in arid soils through determining SOC using an element analyzer, a modified Walkley-Black method and a LOI method with combustion at 375℃ for 17 h and determining SIC using a pressure calcimeter method and a LOI procedure estimated by a weight loss between 375 to 800℃. Our results indicated that the Walkley-Black method provided 99%recovery of SOC for the arid soils tested. There were strong linear relationships(r > 0.93, P < 0.001) for both SOC and SIC between the traditional method and the LOI technique. One set of soil samples was used to develop relationships between LOI and SOC(by the Walkley-Black method), and between LOI and SIC(by the pressure calcimeter method), and the other set of soil samples was used to evaluate the derived equations by comparing predicted SOC and SIC with measured values. The mean absolute errors were small for both SOC (1.7 g C kg-1) and SIC(1.22 g C kg-1), demonstrating that the LOI method was reliable and could provide accurate estimates of SOC and SIC for arid soils.
基金supported by the National Natural Science Foundation of China(Nos.11271273 and 11271298)
文摘A unified analysis is presented for the stabilized methods including the pres- sure projection method and the pressure gradient local projection method of conforming and nonconforming low-order mixed finite elements for the stationary Navier-Stokes equa- tions. The existence and uniqueness of the solution and the optimal error estimates are proved.
基金Project supported by the Science and Technology Foundation of Sichuan Province (No.05GG006- 006-2)the Research Fund for the Introducing Intelligence of University of Electronic Science and Technology of China
文摘A pressure gradient discontinuous finite element formulation for the compressible Navier-Stokes equations is derived based on local projections. The resulting finite element formulation is stable and uniquely solvable without requiring a B-B stability condition. An error estimate is Obtained.
文摘Basis of explosion's responsive analysis and anti-explosion's structure design is the relation among thin explosive mass, impulse and plate deformation. In this paper, the limitations of theoretical calculation and experimental methods are analyzed according to the relation between impulse loading and deformation of steel plate in thin explosive experiment. The time histories of deformation for the square steel plate under the impulse of thin explosive are calculated by the fluid-solid coupling method and the pressure loading method. The advantages of the pressure loading method and the fluid-solid coupling method are compared. The results show that the steel plate deformation can be estimated accurately using the fluid-solid coupling method when the explosive impulse is unknown, while the theoretical calculation and the pressure loading method provide quick and accurate prediction on the steel plate deformation when the explosive impulse is known.
基金supported by the National Natural Science Foundation of China(No.11271273)
文摘For transient Naiver-Stokes problems, a stabilized nonconforming finite element method is presented, focusing on two pairs inf-sup unstable finite element spaces, i.e., pNC/pNC triangular and pNQ/pNQ quadrilateral finite element spaces. The semi- and full-discrete schemes of the stabilized method are studied based on the pressure projection and a variational multi-scale method. It has some attractive features： avoiding higher-order derivatives and edge-based data structures, adding a discrete velocity term only on the fine scale, being effective for high Reynolds number fluid flows, and avoiding increased computation cost. For the full-discrete scheme, it has second-order estimations of time and is unconditionally stable. The presented numerical results agree well with the theoretical results.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.51407197,51522606,51336011,91541120,and 11472306)
文摘Plasma synthetic jet actuator（PSJA） has a wide application prospect in the high-speed flow control field for its high jet velocity.In this paper,the influence of the air pressure on the performance of a two-electrode PSJA is investigated by the schlieren method in a large range from 7 k Pa to 100 k Pa.The energy consumed by the PSJA is roughly the same for all the pressure levels.Traces of the precursor shock wave velocity and the jet front velocity vary a lot for different pressures.The precursor shock wave velocity first decreases gradually and then remains at 345 m/s as the air pressure increases.The peak jet front velocity always appears at the first appearance of a jet,and it decreases gradually with the increase of the air pressure.A maximum precursor shock wave velocity of 520 m/s and a maximum jet front velocity of 440 m/s are observed at the pressure of 7 k Pa.The averaged jet velocity in one period ranges from 44 m/s to 54 m/s for all air pressures,and it drops with the rising of the air pressure.High velocities of the precursor shock wave and the jet front indicate that this type of PSJA can still be used to influence the high-speed flow field at 7 k Pa.
文摘The precise managed pressure drilling(MPD)technology is mainly used to deal with the difficulties encountered when oil and gas open hole sections with multiple pressure systems and the strata with narrow safety density window are drilled through.If its liner cementing is carried out according to the conventional method,lost circulation is inevitable in the process of cementing while the displacement efficiency of smallclearance liner cementing is satisfied.If the positive and inverse injection technology is adopted,the cementing quality cannot meet the requirements of later well test engineering of ultradeep wells.In this paper,the cementing operation ofØ114.3 mm liner in Well Longgang 70 which was drilled in the Jiange structure of the Sichuan Basin was taken as an example to explore the application of the cementing technology based on the precise MPD and pressure balancing method to the cementing of long open-hole sections(as long as 859 m)with both high and low pressures running through multiple reservoirs.On the one hand,the technical measures were taken specifically to ensure the annulus filling efficiency of slurry and the pressure balance in the whole process of cementing.And on the other hand,the annulus pressure balance was precisely controlled by virtue of precise MPD devices and by injecting heavy weight drilling fluids through central pipes,and thus the wellbore pressure was kept steady in the whole process of cementing in the strata with narrow safety density window.It is indicated thatØ114.3 mm liner cementing in this well is good with qualified pressure tests and no channeling emerges at a funnel during the staged density reduction.It is concluded that this method can enhance the liner cementing quality of complex ultradeep gas wells and improve the wellbore conditions for the later safe well tests of high-pressure gas wells.
基金Supported by National Basic Research Program of China(2005cb221504)National Key Technologies R & D Program of China(2006BAK03B01)
文摘An active measurement method and its principle was introduced consideringthe low success rate,special difficulty,and long measurement time of the direct gas pressuremeasurement currently used in coal roadways.The technology of drilling,boreholesealing depth,borehole sealing length,sealing control of the measuring process,compensatorycomputation of gas loss quantity and other key techniques were discussed.Finally,based on the latest instrument the authors developed,a series of experiments of directgas pressure measurement in the coal roadways of the Jincheng and Tongchuanmine district,were carried out.The experimental results show that active gas pressuremeasurement technique has advantages as follows:(1) the application scope of direct gaspressure measurement technique is wide and it does not have the restriction of coalhardness,coal seam fissure and other conditions;(2) the measured results are credible,which can be tested by the same gas pressure value acquired from a different borehole inthe same place;(3) the measurement process is convenient and quick,it takes about 2 to3 days to acquire the gas pressure value in a coal seam.
