This study aims to thoroughly investigate the axial power peaking factors (PPF) within the low-enriched uranium (LEU) core of the Ghana Research Reactor-1 (GHARR-1). This study uses advanced simulation tools, like the...This study aims to thoroughly investigate the axial power peaking factors (PPF) within the low-enriched uranium (LEU) core of the Ghana Research Reactor-1 (GHARR-1). This study uses advanced simulation tools, like the MCNPX code for analysing neutron behavior and the PARET/ANL code for understanding power variations, to get a clearer picture of the reactor’s performance. The analysis covers the initial six years of GHARR-1’s operation and includes projections for its whole 60-year lifespan. We closely observed the patterns of both the highest and average PPFs at 21 axial nodes, with measurements taken every ten years. The findings of this study reveal important patterns in power distribution within the core, which are essential for improving the safety regulations and fuel management techniques of the reactor. We provide a meticulous approach, extensive data, and an analysis of the findings, highlighting the significance of continuous monitoring and analysis for proactive management of nuclear reactors. The findings of this study not only enhance our comprehension of nuclear reactor safety but also carry significant ramifications for sustainable energy progress in Ghana and the wider global context. Nuclear engineering is essential in tackling global concerns, such as the demand for clean and dependable energy sources. Research on optimising nuclear reactors, particularly in terms of safety and efficiency, is crucial for the ongoing advancement and acceptance of nuclear energy.展开更多
In this paper,we present a high peak power passively Q-switched intracavity frequency-doubled green laser based on an efficient LED-pumped Nd:YAG dual-rod laser module.In quasi-continuous wave(QCW)running operation,th...In this paper,we present a high peak power passively Q-switched intracavity frequency-doubled green laser based on an efficient LED-pumped Nd:YAG dual-rod laser module.In quasi-continuous wave(QCW)running operation,the average output power of the fundamental laser at 1064 nm reaches as high as 20.98 W at a repetition rate of 50 Hz with a maximum single pulse energy of 419.6 mJ,corresponding to a maximum optical conversion efficiency of 38.8%and a slope efficiency of 41%.展开更多
Improving power distribution characteristics of space time block codes(STBCs),namely peak to average power ratio(PAPR),average to minimum power ratio(Ave/min),and probability of transmitting"zero"by antenna,...Improving power distribution characteristics of space time block codes(STBCs),namely peak to average power ratio(PAPR),average to minimum power ratio(Ave/min),and probability of transmitting"zero"by antenna,makes easier their practical implementation.To this end,this study proposes to multiply full diversity STB C with a non-singular matrix in multiple input multiple output(MIMO)or multiple input single output(MISO)systems with linear or maximum likelihood(ML)receivers.It is proved that the obtained code achieves full diversity and the order of detection complexity does not change.The proposed method is applied to different types of STBCs.The bit error rate(BER)and power distribution characteristics of the new codes demonstrate the superiority of the introduced method.Further,lower and upper bounds on the BER of the obtained STBCs are derived for all receivers.The proposed method provides trade-off among PAPR,spectral efficiency,energy efficiency,and BER.展开更多
For high-power impulse magnetron sputtering(HIPIMS),the peak power applied to the target is of great importance for regulating the ionization degree of the metal target and ion/atom flux ratio.In this work,chromium(Cr...For high-power impulse magnetron sputtering(HIPIMS),the peak power applied to the target is of great importance for regulating the ionization degree of the metal target and ion/atom flux ratio.In this work,chromium(Cr)films were deposited on 316-L stainless steel substrates and silicon(100) wafers with different peak powers by HIPIMS.The relationship between peak target power and properties of Cr films was explored in detail.The resulting structure and mechanical properties of deposited Cr films were characterized by X-ray diffraction(XRD),transmission electron microscope(TEM),atomic force microscopy(AFM),indentation hardness and scratch tester.The results indicate that the ionization degree of metal target and ion/atom flux ratio increase with the increase in peak power but without the loss of deposition rate at the same time.At low ionization degree,the deposited Cr film has low compressive residual stress and low hardness but good adhesion strength.When the ionization degree of target metal increases with increasing peak power,Cr film exhibits finer size and smoother surface with improved hardness but decreased adhesion strength.展开更多
The test process of electric vehicles (EVs) traction battery peak power is analyzed in detail. Aimed at a special “traction” design of versatile battery—HORIZON~ C~2M Battery, the features are introduced. According...The test process of electric vehicles (EVs) traction battery peak power is analyzed in detail. Aimed at a special “traction” design of versatile battery—HORIZON~ C~2M Battery, the features are introduced. According to the peak power test schedule, the test parameters of HORIZON~ C~2M Battery are calculated and the charging and discharging experiments are carried out. The sustained (30 s) discharge power capability of battery at 2/3 of its open circuit voltage at each of various depths of discharge is determined. The dynamic internal resistance under peak power test is established. Considering the temperature impact during discharging, the peak power capability at each of various depths of discharge is corrected. The correctness of peak power test is validated by combining theory analysis with test results.展开更多
Objective:The Holmium:yttrium-aluminum-garnet(Ho:YAG)laser is the standard lithotrite for ureteroscopy.This paper is to evaluate a Ho:YAG laser with a novel effect function in vitro,which allows a real-time variation ...Objective:The Holmium:yttrium-aluminum-garnet(Ho:YAG)laser is the standard lithotrite for ureteroscopy.This paper is to evaluate a Ho:YAG laser with a novel effect function in vitro,which allows a real-time variation of pulse duration and pulse peak power.Methods:Two types of phantom calculi with four degrees of hardness were made for fragmentation and retropulsion experiments.Fragmentation was analysed at 5(0.5 J/10 Hz),10(1 J/10 Hz),and 20(2 J/10 Hz)W in non-floating phantom calculi,retropulsion in an ureteral model at 10(1 J/10 Hz)and 20(2 J/10 Hz)W using floating phantom calculi.The effect function was set to 25%,50%,75%,and 100%of the maximum possible effect function at each power setting.Primary outcomes:fragmentation(mm^3),the distance of retropulsion(cm);5 measurements for each trial.Results:An increase of the effect feature(25%vs.100%),i.e.,an increase of pulse peak power and decrease of pulse duration,improved Ho:YAG laser fragmentation.This effect was remarkable in soft stone composition,while there was a trend for improved fragmentation with an increase of the effect feature in hard stone composition.Retropulsion increased with increasing effect function,independently of stone composition.The major limitations of the study are the use of artificial stones and the in vitro setup.Conclusion:Changes in pulse duration and pulse peak power may lead to improved stone fragmentation,most prominently in soft stones,but also lead to increased retropulsion.This new effect function may enhance Ho:YAG laser fragmentation when maximum power output is limited or retropulsion is excluded.展开更多
A test pattern generator （TPG） which can highly reduce the peak power consumption during built-in self-test （BIST） application is proposed. The proposed TPG, called LPpe-TPG, consists of a linear feedback shift re...A test pattern generator （TPG） which can highly reduce the peak power consumption during built-in self-test （BIST） application is proposed. The proposed TPG, called LPpe-TPG, consists of a linear feedback shift register （LFSR） and some control circuits. A procedure is presented firstly to make compare vectors between pseudorandom test patterns by adding some circuits to the original LFSR and secondly to insert some vectors between two successive pseudorandom test patterns according to the ordinal selection of every two bits of the compare vector. Then the changes between any successive test patterns of the test set generated by the LPpe-TPG are not more than twice. This leads to a decrease of the weighted switching activity （WSA） of the circuit under test （CUT） and therefore a reduction of the power consumption. Experimental results based on some ISCAS＇ 85 benchmark circuits show that the peak power consumption has been reduced by 25.25% to 64.46%. Also, the effectiveness of our approach to reduce the total and average power consumption is kept, without losing stuck-at fault coverage.展开更多
The laser device is the core component of coherent Doppler wind lidar.The peak power and pulse width of laser transmitting pulse have important effects on SNR.Based on coherent Doppler wind pulse lidar,the peak power ...The laser device is the core component of coherent Doppler wind lidar.The peak power and pulse width of laser transmitting pulse have important effects on SNR.Based on coherent Doppler wind pulse lidar,the peak power and pulse width influence on SNR is studied on the theoretical derivation and analysis,and the results show that the higher the peak power can realize the greater the signal-to-noise ratio of coherent Doppler wind lidar.But when the peak power is too large,the laser pulse may appear nonlinear phenomenon,which cause the damage of the laser.So,the peak power must be less than the stimulated brillouin scattering power threshold.Increasing the pulse width can make the laser device to output more energy,but it will also make the spatial resolution lower,and the influence of turbulence on SNR will be greater.After a series of simulation analyses,it can be concluded that when the peak power is 650W and the pulse width is 340ns,the SNR of the system can be maximized.In addition,the coherent Doppler wind lidar system is set up to carry out corresponding experimental verification.The experimental results are consistent with the theoretical analysis and simulation,which verifies the correctness of the theoretical analysis and simulation results.It provides theoretical basis and practical ex-perience for the design of laser transmitting pulse in coherent Doppler wind lidar system.展开更多
A high peak power IPL system (Lumecca) was tested to determine the correlation between a high peak power and the successful treatment of pigmented and vascular lesions. Short pulse duration in the millisecond range an...A high peak power IPL system (Lumecca) was tested to determine the correlation between a high peak power and the successful treatment of pigmented and vascular lesions. Short pulse duration in the millisecond range and high peak power of 3.3 kW/cm<sup>2</sup> enabled selective and effective destruction, not only of pigment, but also of vessels in a comparable manner to a pulsed dye laser. Only one treatment session at a low fluence (8 - 16 J/cm<sup>2</sup>) was sufficient to achieve the desired results.展开更多
An acoustic-optic Q-switched all-fiber laser With a high-repetition-rate, a short pulse width, a wide spectrum, and a high conversion efficiency is experimentally demonstrated. In the laser configuration, a （1＋1）x ...An acoustic-optic Q-switched all-fiber laser With a high-repetition-rate, a short pulse width, a wide spectrum, and a high conversion efficiency is experimentally demonstrated. In the laser configuration, a （1＋1）x 1 side-pumping coupler is introduced to perform backward pumping, and a 10/130%tm Yb fiber is adopted. The acoustic-optic component operates in the first direction, achieving a Q-switched pulse with a repetition rate adjustable in the range of 20 kHz-80 kHz. Under a repetition rate of 20 kHz and a pump power of 6.76 W, the fiber laser obtains a highly efficient and stable pulse output, with an average power of 4.3 W, a pulse width of 56 ns, a peak power of 3.83 kW, and a power density of 1.39x 101~ W/cm2. Particularly, the optic-optic conversion efficiency of the laser reaches as high as 64%. Another feature of the pulsed laser is that the high reflection mirror reflects the pump light as well, which brings the secondary absorption of the pump power into the gain fiber.展开更多
A Cognitive radio communication link is possible to be interrupted easily when its physical channel suffers severe fading. Relay technology is an effective way to mitigate the fading effect of wireless channels in a n...A Cognitive radio communication link is possible to be interrupted easily when its physical channel suffers severe fading. Relay technology is an effective way to mitigate the fading effect of wireless channels in a network. Based on the highest achievable rate of the relay channels, this paper considers a cognitive radio relay network where the secondary transmitter communicates with the receiver through the best relay node under the peak power constraint of a primary receiver. Intuitively, the secondary transmission can benefit from an intermediate relay node chosen from N possible nodes. To quantify this benefit, outage probability of cognitive radio relay networks is derived and also the closed-form expressions for outage capacity and ergodic capacity of cognitive radio relay networks are obtained in Rayleigh fading channels. Numerical simulation results are provided to show that the outage capacity and ergodic capacity benefit tremendously by properly increasing the number of relaying nodes.展开更多
Data transmission through a wireless network has faced various signal problems in the past decades.The orthogonal frequency division multiplexing(OFDM)technique is widely accepted in multiple data transfer patterns at...Data transmission through a wireless network has faced various signal problems in the past decades.The orthogonal frequency division multiplexing(OFDM)technique is widely accepted in multiple data transfer patterns at various frequency bands.A recent wireless communication network uses OFDM in longterm evolution(LTE)and 5G,among others.The main problem faced by 5G wireless OFDM is distortion of transmission signals in the network.This transmission loss is called peak-to-average power ratio(PAPR).This wireless signal distortion can be reduced using various techniques.This study uses machine learning-based algorithm to solve the problem of PAPR in 5G wireless communication.Partial transmit sequence(PTS)helps in the fast transfer of data in wireless LTE.PTS is merged with deep belief neural network(DBNet)for the efficient processing of signals in wireless 5G networks.Result indicates that the proposed system outperforms other existing techniques.Therefore,PAPR reduction in OFDM by DBNet is optimized with the help of an evolutionary algorithm called particle swarm optimization.Hence,the specified design supports in improving the proposed PAPR reduction architecture.展开更多
The complex-valued modulating vectors for the subcarriers consist of two kinds of components: One is the information-bearing components superposed with pseudo-randomized phases and the other is the suppression compone...The complex-valued modulating vectors for the subcarriers consist of two kinds of components: One is the information-bearing components superposed with pseudo-randomized phases and the other is the suppression components with specified scrambling phases. The pseudo randomized phases are generated according to the predefined polynomial and mapping function whereas the scrambling phases are from a gradient algorithm. The simulation results verify the rationality and validity of the phase scrambling.展开更多
A correlation overlapping partial transmit sequence(C-OPTS) algorithm is proposed to solve the issue of high complexity of overlapping partial transmit sequence(OPTS) algorithm in suppressing the peak to average power...A correlation overlapping partial transmit sequence(C-OPTS) algorithm is proposed to solve the issue of high complexity of overlapping partial transmit sequence(OPTS) algorithm in suppressing the peak to average power ratio(PAPR) of filter bank multicarrier-offset quadrature amplitude modulation(FBMC-OQAM) signals.The V subblocks in partial transmit sequence(PTS) are regrouped into U combinations according to the correlation coefficient p,and overlapping subblocks are allowed between adjacent groups.The search starts from the first group and sets the phase factors of the subsequent groups to 1.When the phase factors of the non-overlapping subblocks in the first group are determined,the subsequent groups are searched in turn to determine their respective phase factors.Starting from the second data block,the data overlapped with it should be taken into account when determining its optimal phase factor vector.Theoretical analysis and simulation results indicate that compared with the OPTS algorithm,the proposed algorithm can significantly reduce the computational complexity at the cost of slight deterioration of PAPR performance.Meanwhile,compared with the even-odd iterative double-layers OPTS(ID-OPTS) algorithm,it can further reduce the complexity and obtain a better PAPR suppression effect.展开更多
A non-sputtering discharge is utilized to verify the effect of replacement of gas ions by metallic ions and consequent decrease in the secondary electron emission coefficient in the discharge current curves in high-po...A non-sputtering discharge is utilized to verify the effect of replacement of gas ions by metallic ions and consequent decrease in the secondary electron emission coefficient in the discharge current curves in high-power impulse magnetron sputtering （HiPIMS）. In the non-sputtering discharge involving hydrogen, replacement of ions is avoided while the rarefaction still contributes. The initial peak and ensuing decay disappear and all the discharge current curves show a similar feature as the HiPIMS discharge of materials with low sputtering yields such as carbon. The results demonstrate the key effect of ion replacement during sputtering.展开更多
A study is presented of the laser welding behaviour of an SiC particulate re-inforced Al-alloy comPOsite using a pulsed Nd-YAG laser. The influences of laser weldingparameters of laser intensity, pulse duration and th...A study is presented of the laser welding behaviour of an SiC particulate re-inforced Al-alloy comPOsite using a pulsed Nd-YAG laser. The influences of laser weldingparameters of laser intensity, pulse duration and the beamjs focus position on the depth ofweld penetration as well as the size of weld bead width were investigated. A typical mi-crostructure of a weld section reveals that the three distinct zones are present. Cracks andporosity were fOund to be two major defects in laser welded metal matrix composites(MMC). These investigations have led to an optimum welding condition proposed forlaser welding of SiC partiulate reinforced aluminium alloy comPosites with minimum de-fects.展开更多
The aim of this work is to present a theoretical study of external magnetic field effect on a bifacial silicon solar cell’s electrical parameters (peak power, fill factor and load resistance) using the J-V and P-V ch...The aim of this work is to present a theoretical study of external magnetic field effect on a bifacial silicon solar cell’s electrical parameters (peak power, fill factor and load resistance) using the J-V and P-V characteristics. After the resolution of the magneto transport equation and continuity equation of excess minority carriers in the base of the bifacial silicon solar cell under multispectral illumination, the photo-current density and the photovoltage are determined and the J-V and P-V curves are plotted. Using simultaneously the J-V and P-V curves, we determine, according to magnetic field intensity, the peak photocurrent density, the peak photovoltage, the peak electric power, the fill factor and the load resistance at the peak power point. The numerical data show that the solar cell’s peak power decreases with magnetic field intensity while the fill factor and the load resistance increase.展开更多
This letter reports the development of a 50MW S-band klystron in the Institute of Electronics, Chinese Academy of Sciences （IECAS）. It adopted a structure of six-cavity and single output window. Under conditions of ...This letter reports the development of a 50MW S-band klystron in the Institute of Electronics, Chinese Academy of Sciences （IECAS）. It adopted a structure of six-cavity and single output window. Under conditions of an RF （Radio Frequency） pulse width of 4t, ts, a beam voltage of 305,9kV and a beam current of 368A, the peak output power has achieved 51.4MW with an efficiency of 45.6% and a gain of 54dB.展开更多
A problem of peak power in DC-electrified railway systems is mainly caused by train power demand during acceleration.If this power is reduced,substation peak power will be significantly decreased.This paper presents a...A problem of peak power in DC-electrified railway systems is mainly caused by train power demand during acceleration.If this power is reduced,substation peak power will be significantly decreased.This paper presents a study on optimal energy saving in DC-electrified railway with on-board energy storage system(OBESS) by using peak demand cutting strategy under different trip time controls.The proposed strategy uses OBESS to store recovered braking energy and find an appropriated time to deliver the stored energy back to the power network in such a way that peak power of every substations is reduced.Bangkok Mass Transit System(BTS)-Silom Line in Thailand is used to test and verify the proposed strategy.The results show that substation peak power is reduced by63.49% and net energy consumption is reduced by 15.56%using coasting and deceleration trip time control.展开更多
This study deals with the problem of mainlobe jamming suppression for rotated array radar.The interference becomes spatially nonstationary while the radar array rotates,which causes the mismatch between the weight and...This study deals with the problem of mainlobe jamming suppression for rotated array radar.The interference becomes spatially nonstationary while the radar array rotates,which causes the mismatch between the weight and the snapshots and thus the loss of target signal to noise ratio(SNR)of pulse compression.In this paper,we explore the spatial divergence of interference sources and consider the rotated array radar anti-mainlobe jamming problem as a generalized rotated array mixed signal(RAMS)model firstly.Then the corresponding algorithm improved blind source separation(BSS)using the frequency domain of robust principal component analysis(FDRPCA-BSS)is proposed based on the established rotating model.It can eliminate the influence of the rotating parts and address the problem of loss of SNR.Finally,the measured peakto-average power ratio(PAPR)of each separated channel is performed to identify the target echo channel among the separated channels.Simulation results show that the proposed method is practically feasible and can suppress the mainlobe jamming with lower loss of SNR.展开更多
文摘This study aims to thoroughly investigate the axial power peaking factors (PPF) within the low-enriched uranium (LEU) core of the Ghana Research Reactor-1 (GHARR-1). This study uses advanced simulation tools, like the MCNPX code for analysing neutron behavior and the PARET/ANL code for understanding power variations, to get a clearer picture of the reactor’s performance. The analysis covers the initial six years of GHARR-1’s operation and includes projections for its whole 60-year lifespan. We closely observed the patterns of both the highest and average PPFs at 21 axial nodes, with measurements taken every ten years. The findings of this study reveal important patterns in power distribution within the core, which are essential for improving the safety regulations and fuel management techniques of the reactor. We provide a meticulous approach, extensive data, and an analysis of the findings, highlighting the significance of continuous monitoring and analysis for proactive management of nuclear reactors. The findings of this study not only enhance our comprehension of nuclear reactor safety but also carry significant ramifications for sustainable energy progress in Ghana and the wider global context. Nuclear engineering is essential in tackling global concerns, such as the demand for clean and dependable energy sources. Research on optimising nuclear reactors, particularly in terms of safety and efficiency, is crucial for the ongoing advancement and acceptance of nuclear energy.
基金supported by the Nanjing University of Posts and Telecommunications Foundation,China(Grant Nos.JUH219002 and JUH219007)the Key R&D Program of Shandong Province,China(Grant No.2021CXGC010202)。
文摘In this paper,we present a high peak power passively Q-switched intracavity frequency-doubled green laser based on an efficient LED-pumped Nd:YAG dual-rod laser module.In quasi-continuous wave(QCW)running operation,the average output power of the fundamental laser at 1064 nm reaches as high as 20.98 W at a repetition rate of 50 Hz with a maximum single pulse energy of 419.6 mJ,corresponding to a maximum optical conversion efficiency of 38.8%and a slope efficiency of 41%.
基金supported by Iran National Science Foundation(INSF)under grant number 93018647。
文摘Improving power distribution characteristics of space time block codes(STBCs),namely peak to average power ratio(PAPR),average to minimum power ratio(Ave/min),and probability of transmitting"zero"by antenna,makes easier their practical implementation.To this end,this study proposes to multiply full diversity STB C with a non-singular matrix in multiple input multiple output(MIMO)or multiple input single output(MISO)systems with linear or maximum likelihood(ML)receivers.It is proved that the obtained code achieves full diversity and the order of detection complexity does not change.The proposed method is applied to different types of STBCs.The bit error rate(BER)and power distribution characteristics of the new codes demonstrate the superiority of the introduced method.Further,lower and upper bounds on the BER of the obtained STBCs are derived for all receivers.The proposed method provides trade-off among PAPR,spectral efficiency,energy efficiency,and BER.
基金financially supported by Joint Fund of National Natural Science Foundation of China and China Academy of Engineering Physics (No.U1330113)the National Natural Science Foundation of China (No.31300787)the Overseas Famous Teacher Program of Chinese Education Ministry (No. MS2010XNJT070)。
文摘For high-power impulse magnetron sputtering(HIPIMS),the peak power applied to the target is of great importance for regulating the ionization degree of the metal target and ion/atom flux ratio.In this work,chromium(Cr)films were deposited on 316-L stainless steel substrates and silicon(100) wafers with different peak powers by HIPIMS.The relationship between peak target power and properties of Cr films was explored in detail.The resulting structure and mechanical properties of deposited Cr films were characterized by X-ray diffraction(XRD),transmission electron microscope(TEM),atomic force microscopy(AFM),indentation hardness and scratch tester.The results indicate that the ionization degree of metal target and ion/atom flux ratio increase with the increase in peak power but without the loss of deposition rate at the same time.At low ionization degree,the deposited Cr film has low compressive residual stress and low hardness but good adhesion strength.When the ionization degree of target metal increases with increasing peak power,Cr film exhibits finer size and smoother surface with improved hardness but decreased adhesion strength.
文摘The test process of electric vehicles (EVs) traction battery peak power is analyzed in detail. Aimed at a special “traction” design of versatile battery—HORIZON~ C~2M Battery, the features are introduced. According to the peak power test schedule, the test parameters of HORIZON~ C~2M Battery are calculated and the charging and discharging experiments are carried out. The sustained (30 s) discharge power capability of battery at 2/3 of its open circuit voltage at each of various depths of discharge is determined. The dynamic internal resistance under peak power test is established. Considering the temperature impact during discharging, the peak power capability at each of various depths of discharge is corrected. The correctness of peak power test is validated by combining theory analysis with test results.
文摘Objective:The Holmium:yttrium-aluminum-garnet(Ho:YAG)laser is the standard lithotrite for ureteroscopy.This paper is to evaluate a Ho:YAG laser with a novel effect function in vitro,which allows a real-time variation of pulse duration and pulse peak power.Methods:Two types of phantom calculi with four degrees of hardness were made for fragmentation and retropulsion experiments.Fragmentation was analysed at 5(0.5 J/10 Hz),10(1 J/10 Hz),and 20(2 J/10 Hz)W in non-floating phantom calculi,retropulsion in an ureteral model at 10(1 J/10 Hz)and 20(2 J/10 Hz)W using floating phantom calculi.The effect function was set to 25%,50%,75%,and 100%of the maximum possible effect function at each power setting.Primary outcomes:fragmentation(mm^3),the distance of retropulsion(cm);5 measurements for each trial.Results:An increase of the effect feature(25%vs.100%),i.e.,an increase of pulse peak power and decrease of pulse duration,improved Ho:YAG laser fragmentation.This effect was remarkable in soft stone composition,while there was a trend for improved fragmentation with an increase of the effect feature in hard stone composition.Retropulsion increased with increasing effect function,independently of stone composition.The major limitations of the study are the use of artificial stones and the in vitro setup.Conclusion:Changes in pulse duration and pulse peak power may lead to improved stone fragmentation,most prominently in soft stones,but also lead to increased retropulsion.This new effect function may enhance Ho:YAG laser fragmentation when maximum power output is limited or retropulsion is excluded.
文摘A test pattern generator （TPG） which can highly reduce the peak power consumption during built-in self-test （BIST） application is proposed. The proposed TPG, called LPpe-TPG, consists of a linear feedback shift register （LFSR） and some control circuits. A procedure is presented firstly to make compare vectors between pseudorandom test patterns by adding some circuits to the original LFSR and secondly to insert some vectors between two successive pseudorandom test patterns according to the ordinal selection of every two bits of the compare vector. Then the changes between any successive test patterns of the test set generated by the LPpe-TPG are not more than twice. This leads to a decrease of the weighted switching activity （WSA） of the circuit under test （CUT） and therefore a reduction of the power consumption. Experimental results based on some ISCAS＇ 85 benchmark circuits show that the peak power consumption has been reduced by 25.25% to 64.46%. Also, the effectiveness of our approach to reduce the total and average power consumption is kept, without losing stuck-at fault coverage.
文摘The laser device is the core component of coherent Doppler wind lidar.The peak power and pulse width of laser transmitting pulse have important effects on SNR.Based on coherent Doppler wind pulse lidar,the peak power and pulse width influence on SNR is studied on the theoretical derivation and analysis,and the results show that the higher the peak power can realize the greater the signal-to-noise ratio of coherent Doppler wind lidar.But when the peak power is too large,the laser pulse may appear nonlinear phenomenon,which cause the damage of the laser.So,the peak power must be less than the stimulated brillouin scattering power threshold.Increasing the pulse width can make the laser device to output more energy,but it will also make the spatial resolution lower,and the influence of turbulence on SNR will be greater.After a series of simulation analyses,it can be concluded that when the peak power is 650W and the pulse width is 340ns,the SNR of the system can be maximized.In addition,the coherent Doppler wind lidar system is set up to carry out corresponding experimental verification.The experimental results are consistent with the theoretical analysis and simulation,which verifies the correctness of the theoretical analysis and simulation results.It provides theoretical basis and practical ex-perience for the design of laser transmitting pulse in coherent Doppler wind lidar system.
文摘A high peak power IPL system (Lumecca) was tested to determine the correlation between a high peak power and the successful treatment of pigmented and vascular lesions. Short pulse duration in the millisecond range and high peak power of 3.3 kW/cm<sup>2</sup> enabled selective and effective destruction, not only of pigment, but also of vessels in a comparable manner to a pulsed dye laser. Only one treatment session at a low fluence (8 - 16 J/cm<sup>2</sup>) was sufficient to achieve the desired results.
基金supported by the National Natural Science Foundation of China(Grant No.61307057)the State Key Laboratory of Tribology,Tsinghua University,China(Grant No.SKLT12B08)China Postdoctoral Science Foundation(Grant Nos.2012M520258 and 2013T60109)
文摘An acoustic-optic Q-switched all-fiber laser With a high-repetition-rate, a short pulse width, a wide spectrum, and a high conversion efficiency is experimentally demonstrated. In the laser configuration, a （1＋1）x 1 side-pumping coupler is introduced to perform backward pumping, and a 10/130%tm Yb fiber is adopted. The acoustic-optic component operates in the first direction, achieving a Q-switched pulse with a repetition rate adjustable in the range of 20 kHz-80 kHz. Under a repetition rate of 20 kHz and a pump power of 6.76 W, the fiber laser obtains a highly efficient and stable pulse output, with an average power of 4.3 W, a pulse width of 56 ns, a peak power of 3.83 kW, and a power density of 1.39x 101~ W/cm2. Particularly, the optic-optic conversion efficiency of the laser reaches as high as 64%. Another feature of the pulsed laser is that the high reflection mirror reflects the pump light as well, which brings the secondary absorption of the pump power into the gain fiber.
文摘A Cognitive radio communication link is possible to be interrupted easily when its physical channel suffers severe fading. Relay technology is an effective way to mitigate the fading effect of wireless channels in a network. Based on the highest achievable rate of the relay channels, this paper considers a cognitive radio relay network where the secondary transmitter communicates with the receiver through the best relay node under the peak power constraint of a primary receiver. Intuitively, the secondary transmission can benefit from an intermediate relay node chosen from N possible nodes. To quantify this benefit, outage probability of cognitive radio relay networks is derived and also the closed-form expressions for outage capacity and ergodic capacity of cognitive radio relay networks are obtained in Rayleigh fading channels. Numerical simulation results are provided to show that the outage capacity and ergodic capacity benefit tremendously by properly increasing the number of relaying nodes.
文摘Data transmission through a wireless network has faced various signal problems in the past decades.The orthogonal frequency division multiplexing(OFDM)technique is widely accepted in multiple data transfer patterns at various frequency bands.A recent wireless communication network uses OFDM in longterm evolution(LTE)and 5G,among others.The main problem faced by 5G wireless OFDM is distortion of transmission signals in the network.This transmission loss is called peak-to-average power ratio(PAPR).This wireless signal distortion can be reduced using various techniques.This study uses machine learning-based algorithm to solve the problem of PAPR in 5G wireless communication.Partial transmit sequence(PTS)helps in the fast transfer of data in wireless LTE.PTS is merged with deep belief neural network(DBNet)for the efficient processing of signals in wireless 5G networks.Result indicates that the proposed system outperforms other existing techniques.Therefore,PAPR reduction in OFDM by DBNet is optimized with the help of an evolutionary algorithm called particle swarm optimization.Hence,the specified design supports in improving the proposed PAPR reduction architecture.
文摘The complex-valued modulating vectors for the subcarriers consist of two kinds of components: One is the information-bearing components superposed with pseudo-randomized phases and the other is the suppression components with specified scrambling phases. The pseudo randomized phases are generated according to the predefined polynomial and mapping function whereas the scrambling phases are from a gradient algorithm. The simulation results verify the rationality and validity of the phase scrambling.
基金Supported by the National Natural Science Foundation of China(No.61601296,61701295,61801286)the Major Scientific and Technological Innovation Projects in Chengdu(No.2019-YF08-00082-GX)the Talent Program of Shanghai University of Engineering Science(No.2018RC43)。
文摘A correlation overlapping partial transmit sequence(C-OPTS) algorithm is proposed to solve the issue of high complexity of overlapping partial transmit sequence(OPTS) algorithm in suppressing the peak to average power ratio(PAPR) of filter bank multicarrier-offset quadrature amplitude modulation(FBMC-OQAM) signals.The V subblocks in partial transmit sequence(PTS) are regrouped into U combinations according to the correlation coefficient p,and overlapping subblocks are allowed between adjacent groups.The search starts from the first group and sets the phase factors of the subsequent groups to 1.When the phase factors of the non-overlapping subblocks in the first group are determined,the subsequent groups are searched in turn to determine their respective phase factors.Starting from the second data block,the data overlapped with it should be taken into account when determining its optimal phase factor vector.Theoretical analysis and simulation results indicate that compared with the OPTS algorithm,the proposed algorithm can significantly reduce the computational complexity at the cost of slight deterioration of PAPR performance.Meanwhile,compared with the even-odd iterative double-layers OPTS(ID-OPTS) algorithm,it can further reduce the complexity and obtain a better PAPR suppression effect.
基金Supported by the National Natural Science Foundation of China under Grant Nos 51301004 and U1330110the Guangdong Innovative and Entrepreneurial Research Team Program under Grant No 2013N080+1 种基金the Shenzhen Science and Technology Research Grant under Grant Nos JCYJ20140903102215536 and JCYJ20150828093127698the City University of Hong Kong Applied Research Grant under Grant No 9667104
文摘A non-sputtering discharge is utilized to verify the effect of replacement of gas ions by metallic ions and consequent decrease in the secondary electron emission coefficient in the discharge current curves in high-power impulse magnetron sputtering （HiPIMS）. In the non-sputtering discharge involving hydrogen, replacement of ions is avoided while the rarefaction still contributes. The initial peak and ensuing decay disappear and all the discharge current curves show a similar feature as the HiPIMS discharge of materials with low sputtering yields such as carbon. The results demonstrate the key effect of ion replacement during sputtering.
文摘A study is presented of the laser welding behaviour of an SiC particulate re-inforced Al-alloy comPOsite using a pulsed Nd-YAG laser. The influences of laser weldingparameters of laser intensity, pulse duration and the beamjs focus position on the depth ofweld penetration as well as the size of weld bead width were investigated. A typical mi-crostructure of a weld section reveals that the three distinct zones are present. Cracks andporosity were fOund to be two major defects in laser welded metal matrix composites(MMC). These investigations have led to an optimum welding condition proposed forlaser welding of SiC partiulate reinforced aluminium alloy comPosites with minimum de-fects.
文摘The aim of this work is to present a theoretical study of external magnetic field effect on a bifacial silicon solar cell’s electrical parameters (peak power, fill factor and load resistance) using the J-V and P-V characteristics. After the resolution of the magneto transport equation and continuity equation of excess minority carriers in the base of the bifacial silicon solar cell under multispectral illumination, the photo-current density and the photovoltage are determined and the J-V and P-V curves are plotted. Using simultaneously the J-V and P-V curves, we determine, according to magnetic field intensity, the peak photocurrent density, the peak photovoltage, the peak electric power, the fill factor and the load resistance at the peak power point. The numerical data show that the solar cell’s peak power decreases with magnetic field intensity while the fill factor and the load resistance increase.
文摘This letter reports the development of a 50MW S-band klystron in the Institute of Electronics, Chinese Academy of Sciences （IECAS）. It adopted a structure of six-cavity and single output window. Under conditions of an RF （Radio Frequency） pulse width of 4t, ts, a beam voltage of 305,9kV and a beam current of 368A, the peak output power has achieved 51.4MW with an efficiency of 45.6% and a gain of 54dB.
文摘A problem of peak power in DC-electrified railway systems is mainly caused by train power demand during acceleration.If this power is reduced,substation peak power will be significantly decreased.This paper presents a study on optimal energy saving in DC-electrified railway with on-board energy storage system(OBESS) by using peak demand cutting strategy under different trip time controls.The proposed strategy uses OBESS to store recovered braking energy and find an appropriated time to deliver the stored energy back to the power network in such a way that peak power of every substations is reduced.Bangkok Mass Transit System(BTS)-Silom Line in Thailand is used to test and verify the proposed strategy.The results show that substation peak power is reduced by63.49% and net energy consumption is reduced by 15.56%using coasting and deceleration trip time control.
基金supported by the National Natural Science Foundation of China(62271255,61871218,61801211)the Fundamental Research Funds for the Central Universities(3082019NC2019002,NG2020001,NP2014504)+2 种基金the Open Research Fund of State Key Laboratory of Space-Ground Integrated Information Technology(2018_SGIIT_KFJJ_AI_03)the Funding of Postgraduate Research Practice&Innovation Program of Jiangsu Province(KYCX200201)the Open Research Fund of the Key Laboratory of Radar Imaging and Microwave Photonics(Nanjing University of Aeronautics and Astronautics),Ministry of E ducation(NJ20210001)。
文摘This study deals with the problem of mainlobe jamming suppression for rotated array radar.The interference becomes spatially nonstationary while the radar array rotates,which causes the mismatch between the weight and the snapshots and thus the loss of target signal to noise ratio(SNR)of pulse compression.In this paper,we explore the spatial divergence of interference sources and consider the rotated array radar anti-mainlobe jamming problem as a generalized rotated array mixed signal(RAMS)model firstly.Then the corresponding algorithm improved blind source separation(BSS)using the frequency domain of robust principal component analysis(FDRPCA-BSS)is proposed based on the established rotating model.It can eliminate the influence of the rotating parts and address the problem of loss of SNR.Finally,the measured peakto-average power ratio(PAPR)of each separated channel is performed to identify the target echo channel among the separated channels.Simulation results show that the proposed method is practically feasible and can suppress the mainlobe jamming with lower loss of SNR.
