Space-Based Solar Power(SBSP) presents a promising solution for achieving carbon neutrality and Renewable Electricity 100%(RE100) goals by offering a stable and continuous energy supply. However, its commercialization...Space-Based Solar Power(SBSP) presents a promising solution for achieving carbon neutrality and Renewable Electricity 100%(RE100) goals by offering a stable and continuous energy supply. However, its commercialization faces significant obstacles due to the technical challenges of long-distance microwave Wireless Power Transmission(WPT) from geostationary orbit. Even ground-based kilometer-scale WPT experiments remain difficult because of limited testing infrastructure, high costs, and strict electromagnetic wave regulations. Since the 1975 NASA-Raytheon experiment, which successfully recovered 30 kW of power over 1.55 km, there has been little progress in extending the transmission distance or increasing the retrieved power. This study proposes a cost-effective methodology for conducting long-range WPT experiments in constrained environments by utilizing existing infrastructure. A deep space antenna operating at 2.08 GHz with an output power of 2.3 kW and a gain of 55.3 dBi was used as the transmitter. Two test configurations were implemented: a 1.81 km ground-to-air test using an aerostat to elevate the receiver and a 1.82 km ground-to-ground test using a ladder truck positioned on a plateau. The rectenna consists of a lightweight 3×3 patch antenna array(0.9 m × 0.9 m), accompanied by a steering device and LED indicators to verify power reception. The aerostat-based test achieved a power density of 154.6 mW/m2, which corresponds to approximately 6.2% of the theoretical maximum. The performance gap is primarily attributed to near-field interference, detuning of the patch antenna, rectifier mismatch, and alignment issues. These limitations are expected to be mitigated through improved patch antenna fabrication, a transition from GaN to GaAs rectifiers optimized for lower input power, and the implementation of an automated alignment system. With these enhancements, the recovered power is expected to improve by approximately four to five times. The results demonstrate a practical and scalable framework for long-range WPT experiments under constrained conditions and provide key insights for advancing SBSP technology.展开更多
The microwave wireless power transmission technologies for space solar power station are a crucial field in the international space sector,where various countries are competing in its development.This paper surveys th...The microwave wireless power transmission technologies for space solar power station are a crucial field in the international space sector,where various countries are competing in its development.This paper surveys the research experiments and development efforts related to space solar power stations and microwave wireless power transmission technologies worldwide.The objective is to assess the progress and current state of this technological foundation,determine the necessary focus for developing high-power microwave wireless power transmission technology,and provide clarity on the direction of future technology development in these areas.Finally,a distributed space solar power station plan that is immediately feasible is proposed.展开更多
In the last decade,space solar power satellites(SSPSs)have been conceived to support net-zero carbon emissions and have attracted considerable attention.Electric energy is transmitted to the ground via a microwave pow...In the last decade,space solar power satellites(SSPSs)have been conceived to support net-zero carbon emissions and have attracted considerable attention.Electric energy is transmitted to the ground via a microwave power beam,a technology known as microwave power transmission(MPT).Due to the vast transmission distance of tens of thousands of kilometers,the power transmitting antenna array must span up to 1 kilometer in diameter.At the same time,the size of the rectifying array on the ground should extend over a few kilometers.This makes the MPT system of SSPSs significantly larger than the existing aerospace engineering system.To design and operate a rational MPT system,comprehensive optimization is required.Taking the space MPT system engineering into consideration,a novel multi-objective optimization function is proposed and further analyzed.The multi-objective optimization problem is modeled mathematically.Beam collection efficiency(BCE)is the primary factor,followed by the thermal management capability.Some tapers,designed to solve the conflict between BCE and the thermal problem,are reviewed.In addition to these two factors,rectenna design complexity is included as a functional factor in the optimization objective.Weight coefficients are assigned to these factors to prioritize them.Radiating planar arrays with different aperture illumination fields are studied,and their performances are compared using the multi-objective optimization function.Transmitting array size,rectifying array size,transmission distance,and transmitted power remaine constant in various cases,ensuring fair comparisons.The analysis results show that the proposed optimization function is effective in optimizing and selecting the MPT system architecture.It is also noted that the multi-objective optimization function can be expanded to include other factors in the future.展开更多
In modern industrial applications,ensuring the reliability of mechanical fittings is critical for maintaining operational safety and efficiency,particularly in power grid systems where split pins serve a pivotal role ...In modern industrial applications,ensuring the reliability of mechanical fittings is critical for maintaining operational safety and efficiency,particularly in power grid systems where split pins serve a pivotal role despite being susceptible to environmental degradation and failure.Existing UAV-based inspection systems are hampered by a low representation of split pin elements and complex backgrounds,leading to challenges in accurate fault detection and timely maintenance.To address this pressing issue,our study proposes an innovative fault detection method for split pins.The approach employs a three-step process:first,cropping operations are used to accurately isolate the fittings containing split pins;second,super-resolution reconstruction is applied to enhance image clarity and detail;and finally,an improved YOLOv8 network,augmented with inner-shape IoU and local window attention mechanisms,is utilized to refine local feature extraction and annotation accuracy.Experimental evaluations on a split pin defect dataset demonstrate robust performance,achieving an accuracy rate of 72.1%and a mean average precision(mAP)of 67.7%,thereby validating the method’s effectiveness under challenging conditions.The proposed approach contributes to the field by specifically targeting the challenges associated with split pin detection in UAV-based inspections,offering a practically applicable and reliably precise method.展开更多
To address the challenges of multi-scale differences,complex background interference,and unstable small target positioning in visual inspection of power towers,the existing methods still face issues such as insufficie...To address the challenges of multi-scale differences,complex background interference,and unstable small target positioning in visual inspection of power towers,the existing methods still face issues such as insufficient feature interaction and unstable confidence estimation,which lead to performance degradation in complex backgrounds and occlusion conditions.This paper proposes a precise inspection method for key power tower components using autonomous drone positioning.To this end,this paper makes three key improvements to the you only look once version 11(YOLOv11)framework.First,it constructs C3k2-adaptive multi-receptive field block(C3k2-AMRB),combining multiple dilated convolutions with a reparameterization mechanism to significantly expand the receptive field and enhance multi-scale feature extraction.Second,it designs a hierarchical wavelet interaction unit(HWIU),which leverages high-and low-frequency decomposition and reconstruction of wavelet transform(WT)to achieve cross-scale semantic alignment,enhancing feature discriminability in complex backgrounds.Third,it proposes a distribution-aware confidence refinement head(DACR-Head),which adaptively calibrates classification confidence based on the statistical characteristics of the predicted bounding-box corner distribution,improving the localization stability and accuracy of small targets.Experiments on the inspection of power line assets dataset(InsPLAD)dataset show that the integrated approach achieves a component detection accuracy at intersection over union(IoU)=0.5(CDA_(50))of 88.3%and a component detection robustness(CDR_(50:95))of 69.8%,respectively,improvements of 4.4%and 7.0%over the baseline.展开更多
Currently,the international economic situation is becoming increasingly complex,and there is significant downward pressure on the global economy.In recent years,China’s infrastructure sector has experienced rapid gro...Currently,the international economic situation is becoming increasingly complex,and there is significant downward pressure on the global economy.In recent years,China’s infrastructure sector has experienced rapid growth,with the structure of its power engineering business gradually shifting from traditional infrastructure construction to more diversified areas such as production and operation,as well as emergency repairs.As a result,the transformation of mechanized construction in power transmission and transformation projects has become increasingly urgent.This article proposes a post-evaluation model based on game theory to improve comprehensive weighting and fuzzy grey relational projection sorting,which can be used to evaluate the optimal mechanized construction scheme for power transmission and transformation projects.The model begins by considering the entire lifecycle of power transmission and transformation projects.It constructs a post-evaluation index system that covers the planning and design stage,on-site construction stage,operation and maintenance stage,and the decommissioning and disposal stage,with corresponding calculation methods for each index.The fuzzy grey correlation projection sorting method is then employed to evaluate and rank the construction schemes.To validate the model’s effectiveness,a case study of a power transmission and transformation project in a specific region of China is used.The comprehensive benefits of three proposed mechanized construction schemes are evaluated and compared.According to the evaluation results,Scheme 1 is ranked the highest,with a membership degree of 0.870945,excelling in sustainability.These results suggest that the proposed model can effectively evaluate and make decisions regarding the optimal mechanized construction plan for power transmission and transformation projects.展开更多
Due to the merits of high inspection speed and long detecting distance, Ultrasonic Guided Wave（UGW） method has been commonly applied to the on-line maintenance of power transmission line. However, the guided wave pr...Due to the merits of high inspection speed and long detecting distance, Ultrasonic Guided Wave（UGW） method has been commonly applied to the on-line maintenance of power transmission line. However, the guided wave propagation in this structure is very complicated, leading to the unfavorable defect localization accuracy. Aiming at this situation, a high precision UGW technique for inspection of local surface defect in power transmission line is proposed. The technique is realized by adopting a novel segmental piezoelectric ring transducer and transducer mounting scheme, combining with the comprehensive characterization of wave propagation and circumferential defect positioning with multiple piezoelectric elements. Firstly, the propagation path of guided waves in the multi-wires of transmission line under the proposed technique condition is investigated experimentally. Next, the wave velocities are calculated by dispersion curves and experiment test respectively, and from comparing of the two results, the guided wave mode propagated in transmission line is confirmed to be F（1,1） mode. Finally, the axial and circumferential positioning of local defective wires in transmission line are both achieved, by using multiple piezoelectric elements to surround the stands and send elastic waves into every single wire. The proposed research can play a role of guiding the development of highly effective UGW method and detecting system for multi-wire transmission line.展开更多
Circularly polarized rectennas operating at X-band are studied in this paper. The quasi-square patches fed by aperture coupling are used as the circularly polarized receiving antennas, which are easily matched and int...Circularly polarized rectennas operating at X-band are studied in this paper. The quasi-square patches fed by aperture coupling are used as the circularly polarized receiving antennas, which are easily matched and integrated with the circuits of rectennas. The double-layer structure not only minimizes the size of the rectennas but also decreases the effects of the circuits on the an- tenna. The receiving elements have broader bandwidth and higher gain than the single-layer patches. Two rectennas operating at 10GHz are designed, fabricated and measured. The voltage of 3.86V on a load of 200? is measured and a high RF-DC conversion efficiency of 75% is obtained at 9.98GHz. It is convenient for this kind of rectennas to form large arrays for high power applications.展开更多
Coupled-plate structures are widely used in the practical engineering such as aeronautical,civil and naval engineering etc.Limited works can be found on the vibration of the coupled-plate structure due to the increase...Coupled-plate structures are widely used in the practical engineering such as aeronautical,civil and naval engineering etc.Limited works can be found on the vibration of the coupled-plate structure due to the increased mathematical complexity compared with the single plate structure.In order to study analytically the vibration characteristics and power transmission of the coupled-plate structure,an analytical model consisting of three coupled plates elastically restrained along boundary edges and elastically coupled with arbitrary angle is considered,in which four groups of springs are distributed consistently along each edge of the model to simulate the transverse shearing forces,bending moments,in-plane longitudinal forces and in-plane shearing forces separately.With elastic coupling condition and general boundary condition of both flexural and in-plane vibrations taken into account by setting the stiffness of corresponding springs,the double Fourier series solution to the dynamic response of the structure was obtained by employing the Rayleigh-Ritz method.In order to validate the model,the natural frequency and velocity response of the model are firstly checked against results published in literatures and the ANSYS data,and good agreement was observed.Then,numerical simulation of the effects of several relevant parameters on the vibration characteristics and power transmission of the coupled structure were performed,including boundary conditions,coupling conditions,coupling angle,and location of the external forces.Vibration and energy transmission behaviors were analyzed numerically.The results show that the power transmission can be significantly influenced by the boundary restraints and the location of excitation.When the excitation is located at the central symmetry point of the model,the energy flow shows a symmetrical distribution.Once the location deviates from the central symmetry point,the power circumfluence occurs and the vortex energy field is formed at high frequency.展开更多
This work presents an optimal design method of antenna aperture illumination for microwave power transmission with an annular collection area.The objective is to maximize the ratio of the power radiated on the annular...This work presents an optimal design method of antenna aperture illumination for microwave power transmission with an annular collection area.The objective is to maximize the ratio of the power radiated on the annular collection area to the total transmitted power.By formulating the aperture amplitude distribution through a summation of a special set of series,the optimal design problem can be reduced to finding the maximum ratio of two real quadratic forms.Based on the theory of matrices,the solution to the formulated optimization problem is to determine the largest characteristic value and its associated characteristic vector.To meet security requirements,the peak radiation levels outside the receiving area are considered to be extra constraints.A hybrid grey wolf optimizer and Nelder–Mead simplex method is developed to deal with this constrained optimization problem.In order to demonstrate the effectiveness of the proposed method,numerical experiments on continuous apertures are conducted;then,discrete arrays of isotropic elements are employed to validate the correctness of the optimized results.Finally,patch arrays are adopted to further verify the validity of the proposed method.展开更多
Electrical pollution is a worldwide concern,because it is potentially harmful to human health.Trees not only play a significant role in moderating the climate,but also can be used as shields against electrical polluti...Electrical pollution is a worldwide concern,because it is potentially harmful to human health.Trees not only play a significant role in moderating the climate,but also can be used as shields against electrical pollution.Shielding effects on the electric field strength under transmission lines by two tree species,Populus alba and Larix gmelinii,were examined in this study.The electrical resistivity at different heights of trees was measured using a PiCUS sonic tomograph,which can image the electrical impedance for trees.The electric field strength around the trees was measured with an elf field strength measurement system,HI-3604,and combined with tree resistivity to develop a model for calculating the electric field intensity around trees using the finite element method.In addition,the feasibility of the finite element method was confirmed by comparing the calculated results and experimental data.The results showed that the trees did reduce the electric field strength.The electric field intensity was reduced by 95.6%,and P.alba was better than L.gmelinii at shielding.展开更多
An experimental study is conducted on several retro-reflective beamforming schemes for wireless power transmission to multiple wireless power receivers(referred to herein as“targets”).The experimental results demons...An experimental study is conducted on several retro-reflective beamforming schemes for wireless power transmission to multiple wireless power receivers(referred to herein as“targets”).The experimental results demonstrate that,when multiple targets broadcast continuous-wave pilot signals at respective frequencies,a retro-reflective wireless power transmitter is capable of generating multiple wireless power beams aiming at the respective targets as long as the multiple pilot signals are explicitly separated from one another by the wireless power transmitter.However,various practical complications are identified when the pilot signals of multiple targets are not appropriately differentiated from each other by the wireless power transmitter.Specifically,when multiple pilot signals are considered to be carried by the same frequency,the wireless power transmission performance becomes heavily dependent on the interaction among the pilot signals,which is highly undesirable in practice.In conclusion,it is essential for a retro-reflective wireless power transmitter to explicitly discriminate multiple targets’pilot signals among each other.展开更多
Three design methods for wireless power transmission(WPT)systems using antenna arrays have been investigated.The three methods,corresponding to three common application scenarios of WPT systems,are based on the method...Three design methods for wireless power transmission(WPT)systems using antenna arrays have been investigated.The three methods,corresponding to three common application scenarios of WPT systems,are based on the method of maximum power transmission efficiency(MMPTE)between two antenna arrays.They are unconstrained MMPTE,weighted MMPTE,and constrained MMPTE.To demonstrate the optimal design process with the three methods,a WPT system operating at 2.45 GHz is designed,simulated,and fabricated,in which the transmitting(Tx)array,consisting of 36 microstrip patch elements,is configured as a square and the receiving(Rx)array,consisting of 5 patch elements,is configured as an L shape.The power transmission efficiency(PTE)is then maximized for the three application scenarios,which yields the maximum possible PTEs and the optimized distributions of excitations for both Tx and Rx arrays.The feeding networks are then built based on the optimized distributions of excitations.Simulations and experiments reveal that the unconstrained MMPTE,which corresponds to the application scenario where no radiation pattern shaping is involved,yields the highest PTE.The next highest PTE belongs to the weighted MMPTE,where the power levels at all the receiving elements are imposed to be equal.The constrained MMPTE has the lowest PTE,corresponding to the scenario in which the radiated power pattern is assumed to be flat along with the Rx array.展开更多
Wireless power transmission based on inductive coupling for remotely implanted micro devices has been considered in this paper. The receiving coil, integrated in microsystems and the external transmitting coil compose...Wireless power transmission based on inductive coupling for remotely implanted micro devices has been considered in this paper. The receiving coil, integrated in microsystems and the external transmitting coil compose a loosely coupled transformer. The coupling coefficient was calculated and measured on spacing misalignments. The geometric size of transmitting coil was analyzed for the target of remotely delivering power. The received power was maximized by choosing appropriate value of frequency, tuning capacitance and the load resistance. A conventional full bridge rectifier circuit was employed to convert ac to dc voltage. The received dc power was up to 160 mW with a transmitting vohage of 5 Vrms when the receiving coil was placed at the center of the transmitting coil. This may meet the requirement of some microsystems for high power over a long time.展开更多
In this paper,the case of a battery charger for electric vehicles based on a wireless power transmission is addressed.The specificity of every stage of the overall system is presented.Based on calculated and measured ...In this paper,the case of a battery charger for electric vehicles based on a wireless power transmission is addressed.The specificity of every stage of the overall system is presented.Based on calculated and measured results,relevant capacitive compensations of the transformer and models are suggested and discussed in order to best match the operating mode and aiming at simplifying as much as possible the control and the electronics of the charger.展开更多
This paper presents a theoretical design method for a magnetic energy harvesting module. This module consists of an air-core coil and resonant capacitor. With a simple RLC circuit model, it can derive an equation of h...This paper presents a theoretical design method for a magnetic energy harvesting module. This module consists of an air-core coil and resonant capacitor. With a simple RLC circuit model, it can derive an equation of harvesting energy as a function of coil size. In order to demonstrate the magnetic field, a uniform magnetic field is generated by the developed coil system. From the experimented results, it is successfully demonstrated 100 mW of energy harvesting from a magnetic field of 0.09 mT at 60 Hz. This value is in good agreement with the estimated results. Harvested energy is proportional to the square of the magnetic flux density. However, ICNIRP2010 provides a guideline that an acceptable level for human health in a public space is 0.2 mT at power-line frequency. This paper also discuss the possibilities of several applications related with both magnetic energy harvesting and wireless power transmission.展开更多
A conceptual superconducting DC cable model is designed and its magnetic fields distribution is analyzed with Ansoft/Maxwell soft. A DC Power transmission system is also studied by using the Matlab/Simulink. With the ...A conceptual superconducting DC cable model is designed and its magnetic fields distribution is analyzed with Ansoft/Maxwell soft. A DC Power transmission system is also studied by using the Matlab/Simulink. With the DC Line and AC Ground Fault, the system losses analysis is introduced.The analysis results mainly include the magnetic fields distribution of the HTS cable model with Ansoft/Maxwell, the system loss, the DC Line and AC Ground Fault with Matlab/Simulation.展开更多
Retro reflective beamforming technique has the potential of enabling efficient wireless power transmission over long distance(on the order of meters and even kilometers).In retro reflective beamforming,wireless power ...Retro reflective beamforming technique has the potential of enabling efficient wireless power transmission over long distance(on the order of meters and even kilometers).In retro reflective beamforming,wireless power transmission is guided by pilot signal:Based upon pilot signal broadcasted by a wireless power receiver,a wireless power transmitter delivers focused microwave power beam(s)onto the location of wireless power receiver.When the wireless power receiver’s location is not fixed or when the wireless power receiver’s location is unknown to the wireless power transmitter,the microwave power beam would follow the wireless power receiver’s location dynamically as long as the wireless power receiver broadcasts pilot signal periodically.This paper reviews our research endeavors in recent years on retro reflective beamforming technique targeting three applications:(1)wireless charging for low power mobile/portable electronic devices,(2)space solar power satellites(SSPS)application,and(3)wireless charging in fully enclosed space.The feasibility and potential of retro reflective beamforming technique with applications in wireless power transmission are demonstrated by some preliminary experimental results.展开更多
Date: April 12-15, 2005 Venue: Zhejiang University, Hangzhou, P. R. China Organized by Institute of Mechatronic Control Engineering, Zhejiang University
A microstrip loop resonator loaded with a lumped capacitor is proposed for short-range wireless power transmission applications.The overall physical dimensions of the proposed loop resonator configuration are as small...A microstrip loop resonator loaded with a lumped capacitor is proposed for short-range wireless power transmission applications.The overall physical dimensions of the proposed loop resonator configuration are as small as 3 cm by 3 cm.Power transmission efficiency of greater than 80%is achieved with a power transmission distance smaller than 5 mm via the strong coupling between two loop resonators around 1 GHz,as demonstrated by simulations and measurements.Experimental results also show that the power transmission performance is insensitive to various geometrical misalignments.The numerical and experimental results of this paper reveal a bandwidth of more than 50 MHz within which the power transmission efficiency is above 80%.As a result,the proposed microstrip loop resonator has the potential to accomplish efficient wireless power transmission and high-speed(higher than 10 Mbit/s)wireless communication simultaneously.展开更多
文摘Space-Based Solar Power(SBSP) presents a promising solution for achieving carbon neutrality and Renewable Electricity 100%(RE100) goals by offering a stable and continuous energy supply. However, its commercialization faces significant obstacles due to the technical challenges of long-distance microwave Wireless Power Transmission(WPT) from geostationary orbit. Even ground-based kilometer-scale WPT experiments remain difficult because of limited testing infrastructure, high costs, and strict electromagnetic wave regulations. Since the 1975 NASA-Raytheon experiment, which successfully recovered 30 kW of power over 1.55 km, there has been little progress in extending the transmission distance or increasing the retrieved power. This study proposes a cost-effective methodology for conducting long-range WPT experiments in constrained environments by utilizing existing infrastructure. A deep space antenna operating at 2.08 GHz with an output power of 2.3 kW and a gain of 55.3 dBi was used as the transmitter. Two test configurations were implemented: a 1.81 km ground-to-air test using an aerostat to elevate the receiver and a 1.82 km ground-to-ground test using a ladder truck positioned on a plateau. The rectenna consists of a lightweight 3×3 patch antenna array(0.9 m × 0.9 m), accompanied by a steering device and LED indicators to verify power reception. The aerostat-based test achieved a power density of 154.6 mW/m2, which corresponds to approximately 6.2% of the theoretical maximum. The performance gap is primarily attributed to near-field interference, detuning of the patch antenna, rectifier mismatch, and alignment issues. These limitations are expected to be mitigated through improved patch antenna fabrication, a transition from GaN to GaAs rectifiers optimized for lower input power, and the implementation of an automated alignment system. With these enhancements, the recovered power is expected to improve by approximately four to five times. The results demonstrate a practical and scalable framework for long-range WPT experiments under constrained conditions and provide key insights for advancing SBSP technology.
基金Entrusted Fund of National Institute of Information and Communications Technology(NICT),Japan(JPJ012368C02401)。
文摘The microwave wireless power transmission technologies for space solar power station are a crucial field in the international space sector,where various countries are competing in its development.This paper surveys the research experiments and development efforts related to space solar power stations and microwave wireless power transmission technologies worldwide.The objective is to assess the progress and current state of this technological foundation,determine the necessary focus for developing high-power microwave wireless power transmission technology,and provide clarity on the direction of future technology development in these areas.Finally,a distributed space solar power station plan that is immediately feasible is proposed.
文摘In the last decade,space solar power satellites(SSPSs)have been conceived to support net-zero carbon emissions and have attracted considerable attention.Electric energy is transmitted to the ground via a microwave power beam,a technology known as microwave power transmission(MPT).Due to the vast transmission distance of tens of thousands of kilometers,the power transmitting antenna array must span up to 1 kilometer in diameter.At the same time,the size of the rectifying array on the ground should extend over a few kilometers.This makes the MPT system of SSPSs significantly larger than the existing aerospace engineering system.To design and operate a rational MPT system,comprehensive optimization is required.Taking the space MPT system engineering into consideration,a novel multi-objective optimization function is proposed and further analyzed.The multi-objective optimization problem is modeled mathematically.Beam collection efficiency(BCE)is the primary factor,followed by the thermal management capability.Some tapers,designed to solve the conflict between BCE and the thermal problem,are reviewed.In addition to these two factors,rectenna design complexity is included as a functional factor in the optimization objective.Weight coefficients are assigned to these factors to prioritize them.Radiating planar arrays with different aperture illumination fields are studied,and their performances are compared using the multi-objective optimization function.Transmitting array size,rectifying array size,transmission distance,and transmitted power remaine constant in various cases,ensuring fair comparisons.The analysis results show that the proposed optimization function is effective in optimizing and selecting the MPT system architecture.It is also noted that the multi-objective optimization function can be expanded to include other factors in the future.
基金Fundamental Research Funds for the Central Universities(2023MS134)。
文摘In modern industrial applications,ensuring the reliability of mechanical fittings is critical for maintaining operational safety and efficiency,particularly in power grid systems where split pins serve a pivotal role despite being susceptible to environmental degradation and failure.Existing UAV-based inspection systems are hampered by a low representation of split pin elements and complex backgrounds,leading to challenges in accurate fault detection and timely maintenance.To address this pressing issue,our study proposes an innovative fault detection method for split pins.The approach employs a three-step process:first,cropping operations are used to accurately isolate the fittings containing split pins;second,super-resolution reconstruction is applied to enhance image clarity and detail;and finally,an improved YOLOv8 network,augmented with inner-shape IoU and local window attention mechanisms,is utilized to refine local feature extraction and annotation accuracy.Experimental evaluations on a split pin defect dataset demonstrate robust performance,achieving an accuracy rate of 72.1%and a mean average precision(mAP)of 67.7%,thereby validating the method’s effectiveness under challenging conditions.The proposed approach contributes to the field by specifically targeting the challenges associated with split pin detection in UAV-based inspections,offering a practically applicable and reliably precise method.
基金supported by the National Natural Science Foundation of China(No.61702347)Hebei Academy of Sciences Basic Research Operating Fund Project(No.2025PF21)。
文摘To address the challenges of multi-scale differences,complex background interference,and unstable small target positioning in visual inspection of power towers,the existing methods still face issues such as insufficient feature interaction and unstable confidence estimation,which lead to performance degradation in complex backgrounds and occlusion conditions.This paper proposes a precise inspection method for key power tower components using autonomous drone positioning.To this end,this paper makes three key improvements to the you only look once version 11(YOLOv11)framework.First,it constructs C3k2-adaptive multi-receptive field block(C3k2-AMRB),combining multiple dilated convolutions with a reparameterization mechanism to significantly expand the receptive field and enhance multi-scale feature extraction.Second,it designs a hierarchical wavelet interaction unit(HWIU),which leverages high-and low-frequency decomposition and reconstruction of wavelet transform(WT)to achieve cross-scale semantic alignment,enhancing feature discriminability in complex backgrounds.Third,it proposes a distribution-aware confidence refinement head(DACR-Head),which adaptively calibrates classification confidence based on the statistical characteristics of the predicted bounding-box corner distribution,improving the localization stability and accuracy of small targets.Experiments on the inspection of power line assets dataset(InsPLAD)dataset show that the integrated approach achieves a component detection accuracy at intersection over union(IoU)=0.5(CDA_(50))of 88.3%and a component detection robustness(CDR_(50:95))of 69.8%,respectively,improvements of 4.4%and 7.0%over the baseline.
文摘Currently,the international economic situation is becoming increasingly complex,and there is significant downward pressure on the global economy.In recent years,China’s infrastructure sector has experienced rapid growth,with the structure of its power engineering business gradually shifting from traditional infrastructure construction to more diversified areas such as production and operation,as well as emergency repairs.As a result,the transformation of mechanized construction in power transmission and transformation projects has become increasingly urgent.This article proposes a post-evaluation model based on game theory to improve comprehensive weighting and fuzzy grey relational projection sorting,which can be used to evaluate the optimal mechanized construction scheme for power transmission and transformation projects.The model begins by considering the entire lifecycle of power transmission and transformation projects.It constructs a post-evaluation index system that covers the planning and design stage,on-site construction stage,operation and maintenance stage,and the decommissioning and disposal stage,with corresponding calculation methods for each index.The fuzzy grey correlation projection sorting method is then employed to evaluate and rank the construction schemes.To validate the model’s effectiveness,a case study of a power transmission and transformation project in a specific region of China is used.The comprehensive benefits of three proposed mechanized construction schemes are evaluated and compared.According to the evaluation results,Scheme 1 is ranked the highest,with a membership degree of 0.870945,excelling in sustainability.These results suggest that the proposed model can effectively evaluate and make decisions regarding the optimal mechanized construction plan for power transmission and transformation projects.
基金Supported by National Natural Science Foundation of China(Grant No51605229)Natural Science Foundation of Higher Education Institutions of Jiangsu Province,China(Grant No.16KJB460016)+1 种基金the“333”Project of Jiangsu Province,China(Grant No.BRA2015310)China Postdoctora Science Foundation(Grant No.2016M601844)
文摘Due to the merits of high inspection speed and long detecting distance, Ultrasonic Guided Wave（UGW） method has been commonly applied to the on-line maintenance of power transmission line. However, the guided wave propagation in this structure is very complicated, leading to the unfavorable defect localization accuracy. Aiming at this situation, a high precision UGW technique for inspection of local surface defect in power transmission line is proposed. The technique is realized by adopting a novel segmental piezoelectric ring transducer and transducer mounting scheme, combining with the comprehensive characterization of wave propagation and circumferential defect positioning with multiple piezoelectric elements. Firstly, the propagation path of guided waves in the multi-wires of transmission line under the proposed technique condition is investigated experimentally. Next, the wave velocities are calculated by dispersion curves and experiment test respectively, and from comparing of the two results, the guided wave mode propagated in transmission line is confirmed to be F（1,1） mode. Finally, the axial and circumferential positioning of local defective wires in transmission line are both achieved, by using multiple piezoelectric elements to surround the stands and send elastic waves into every single wire. The proposed research can play a role of guiding the development of highly effective UGW method and detecting system for multi-wire transmission line.
基金Supported by the Development Fund of Shanghai Edu-cation Committee and Shanghai Leading Academic Dis-cipline Project (No.T0102)
文摘Circularly polarized rectennas operating at X-band are studied in this paper. The quasi-square patches fed by aperture coupling are used as the circularly polarized receiving antennas, which are easily matched and integrated with the circuits of rectennas. The double-layer structure not only minimizes the size of the rectennas but also decreases the effects of the circuits on the an- tenna. The receiving elements have broader bandwidth and higher gain than the single-layer patches. Two rectennas operating at 10GHz are designed, fabricated and measured. The voltage of 3.86V on a load of 200? is measured and a high RF-DC conversion efficiency of 75% is obtained at 9.98GHz. It is convenient for this kind of rectennas to form large arrays for high power applications.
基金supported by National Natural Science Foundation of China (Grant No. 10802024)Research Fund for the Doctoral Program of Higher Education of China (Grant No. 200802171009)Innovative Talents Fund of Harbin of China(Grant No.2009RFQXG211)
文摘Coupled-plate structures are widely used in the practical engineering such as aeronautical,civil and naval engineering etc.Limited works can be found on the vibration of the coupled-plate structure due to the increased mathematical complexity compared with the single plate structure.In order to study analytically the vibration characteristics and power transmission of the coupled-plate structure,an analytical model consisting of three coupled plates elastically restrained along boundary edges and elastically coupled with arbitrary angle is considered,in which four groups of springs are distributed consistently along each edge of the model to simulate the transverse shearing forces,bending moments,in-plane longitudinal forces and in-plane shearing forces separately.With elastic coupling condition and general boundary condition of both flexural and in-plane vibrations taken into account by setting the stiffness of corresponding springs,the double Fourier series solution to the dynamic response of the structure was obtained by employing the Rayleigh-Ritz method.In order to validate the model,the natural frequency and velocity response of the model are firstly checked against results published in literatures and the ANSYS data,and good agreement was observed.Then,numerical simulation of the effects of several relevant parameters on the vibration characteristics and power transmission of the coupled structure were performed,including boundary conditions,coupling conditions,coupling angle,and location of the external forces.Vibration and energy transmission behaviors were analyzed numerically.The results show that the power transmission can be significantly influenced by the boundary restraints and the location of excitation.When the excitation is located at the central symmetry point of the model,the energy flow shows a symmetrical distribution.Once the location deviates from the central symmetry point,the power circumfluence occurs and the vortex energy field is formed at high frequency.
基金supported in part by the National Key Research and Development Program of China(2021YFB3900300)in part by the National Natural Science Foundation of China(62201416)+2 种基金in part by the Fundamental Research Funds for the Central Universities(QTZX23070)in part by the Qin Chuang Yuan High-Level Innovative and Entrepreneurial Talents Project(QCYRCXM-2022-314)in part by Singapore Ministry of Education Academic Research Fund Tier 1。
文摘This work presents an optimal design method of antenna aperture illumination for microwave power transmission with an annular collection area.The objective is to maximize the ratio of the power radiated on the annular collection area to the total transmitted power.By formulating the aperture amplitude distribution through a summation of a special set of series,the optimal design problem can be reduced to finding the maximum ratio of two real quadratic forms.Based on the theory of matrices,the solution to the formulated optimization problem is to determine the largest characteristic value and its associated characteristic vector.To meet security requirements,the peak radiation levels outside the receiving area are considered to be extra constraints.A hybrid grey wolf optimizer and Nelder–Mead simplex method is developed to deal with this constrained optimization problem.In order to demonstrate the effectiveness of the proposed method,numerical experiments on continuous apertures are conducted;then,discrete arrays of isotropic elements are employed to validate the correctness of the optimized results.Finally,patch arrays are adopted to further verify the validity of the proposed method.
基金financially supported by the National Key Research and Development Program(2017YFD0600101)the Central University Basic Research and Operating Expenses of Special Funding(2572016CB04)the Harbin Application Technology Research and Development Projects(2016RQQXJ134)
文摘Electrical pollution is a worldwide concern,because it is potentially harmful to human health.Trees not only play a significant role in moderating the climate,but also can be used as shields against electrical pollution.Shielding effects on the electric field strength under transmission lines by two tree species,Populus alba and Larix gmelinii,were examined in this study.The electrical resistivity at different heights of trees was measured using a PiCUS sonic tomograph,which can image the electrical impedance for trees.The electric field strength around the trees was measured with an elf field strength measurement system,HI-3604,and combined with tree resistivity to develop a model for calculating the electric field intensity around trees using the finite element method.In addition,the feasibility of the finite element method was confirmed by comparing the calculated results and experimental data.The results showed that the trees did reduce the electric field strength.The electric field intensity was reduced by 95.6%,and P.alba was better than L.gmelinii at shielding.
基金supported in part by the National Natural Science Foundation of China(61871220)the Natural Science Foundation of Jiangsu Province(BK20201293)。
文摘An experimental study is conducted on several retro-reflective beamforming schemes for wireless power transmission to multiple wireless power receivers(referred to herein as“targets”).The experimental results demonstrate that,when multiple targets broadcast continuous-wave pilot signals at respective frequencies,a retro-reflective wireless power transmitter is capable of generating multiple wireless power beams aiming at the respective targets as long as the multiple pilot signals are explicitly separated from one another by the wireless power transmitter.However,various practical complications are identified when the pilot signals of multiple targets are not appropriately differentiated from each other by the wireless power transmitter.Specifically,when multiple pilot signals are considered to be carried by the same frequency,the wireless power transmission performance becomes heavily dependent on the interaction among the pilot signals,which is highly undesirable in practice.In conclusion,it is essential for a retro-reflective wireless power transmitter to explicitly discriminate multiple targets’pilot signals among each other.
基金the National Natural Science Foundation of China under Grant No.61971231.
文摘Three design methods for wireless power transmission(WPT)systems using antenna arrays have been investigated.The three methods,corresponding to three common application scenarios of WPT systems,are based on the method of maximum power transmission efficiency(MMPTE)between two antenna arrays.They are unconstrained MMPTE,weighted MMPTE,and constrained MMPTE.To demonstrate the optimal design process with the three methods,a WPT system operating at 2.45 GHz is designed,simulated,and fabricated,in which the transmitting(Tx)array,consisting of 36 microstrip patch elements,is configured as a square and the receiving(Rx)array,consisting of 5 patch elements,is configured as an L shape.The power transmission efficiency(PTE)is then maximized for the three application scenarios,which yields the maximum possible PTEs and the optimized distributions of excitations for both Tx and Rx arrays.The feeding networks are then built based on the optimized distributions of excitations.Simulations and experiments reveal that the unconstrained MMPTE,which corresponds to the application scenario where no radiation pattern shaping is involved,yields the highest PTE.The next highest PTE belongs to the weighted MMPTE,where the power levels at all the receiving elements are imposed to be equal.The constrained MMPTE has the lowest PTE,corresponding to the scenario in which the radiated power pattern is assumed to be flat along with the Rx array.
基金National High Technology Research and Development Program of China(863 Program),Grant number:2004AA404013.
文摘Wireless power transmission based on inductive coupling for remotely implanted micro devices has been considered in this paper. The receiving coil, integrated in microsystems and the external transmitting coil compose a loosely coupled transformer. The coupling coefficient was calculated and measured on spacing misalignments. The geometric size of transmitting coil was analyzed for the target of remotely delivering power. The received power was maximized by choosing appropriate value of frequency, tuning capacitance and the load resistance. A conventional full bridge rectifier circuit was employed to convert ac to dc voltage. The received dc power was up to 160 mW with a transmitting vohage of 5 Vrms when the receiving coil was placed at the center of the transmitting coil. This may meet the requirement of some microsystems for high power over a long time.
文摘In this paper,the case of a battery charger for electric vehicles based on a wireless power transmission is addressed.The specificity of every stage of the overall system is presented.Based on calculated and measured results,relevant capacitive compensations of the transformer and models are suggested and discussed in order to best match the operating mode and aiming at simplifying as much as possible the control and the electronics of the charger.
文摘This paper presents a theoretical design method for a magnetic energy harvesting module. This module consists of an air-core coil and resonant capacitor. With a simple RLC circuit model, it can derive an equation of harvesting energy as a function of coil size. In order to demonstrate the magnetic field, a uniform magnetic field is generated by the developed coil system. From the experimented results, it is successfully demonstrated 100 mW of energy harvesting from a magnetic field of 0.09 mT at 60 Hz. This value is in good agreement with the estimated results. Harvested energy is proportional to the square of the magnetic flux density. However, ICNIRP2010 provides a guideline that an acceptable level for human health in a public space is 0.2 mT at power-line frequency. This paper also discuss the possibilities of several applications related with both magnetic energy harvesting and wireless power transmission.
文摘A conceptual superconducting DC cable model is designed and its magnetic fields distribution is analyzed with Ansoft/Maxwell soft. A DC Power transmission system is also studied by using the Matlab/Simulink. With the DC Line and AC Ground Fault, the system losses analysis is introduced.The analysis results mainly include the magnetic fields distribution of the HTS cable model with Ansoft/Maxwell, the system loss, the DC Line and AC Ground Fault with Matlab/Simulation.
基金supported in part by the National Natural Science Foundations of China (Nos. 61871220, 61471195, 61628106)the United States National Science Foundation (Nos. ECCS 1303142, ECCS 1503600)
文摘Retro reflective beamforming technique has the potential of enabling efficient wireless power transmission over long distance(on the order of meters and even kilometers).In retro reflective beamforming,wireless power transmission is guided by pilot signal:Based upon pilot signal broadcasted by a wireless power receiver,a wireless power transmitter delivers focused microwave power beam(s)onto the location of wireless power receiver.When the wireless power receiver’s location is not fixed or when the wireless power receiver’s location is unknown to the wireless power transmitter,the microwave power beam would follow the wireless power receiver’s location dynamically as long as the wireless power receiver broadcasts pilot signal periodically.This paper reviews our research endeavors in recent years on retro reflective beamforming technique targeting three applications:(1)wireless charging for low power mobile/portable electronic devices,(2)space solar power satellites(SSPS)application,and(3)wireless charging in fully enclosed space.The feasibility and potential of retro reflective beamforming technique with applications in wireless power transmission are demonstrated by some preliminary experimental results.
文摘Date: April 12-15, 2005 Venue: Zhejiang University, Hangzhou, P. R. China Organized by Institute of Mechatronic Control Engineering, Zhejiang University
基金the National Natural Science Foundation of China under Grant No.61871220.
文摘A microstrip loop resonator loaded with a lumped capacitor is proposed for short-range wireless power transmission applications.The overall physical dimensions of the proposed loop resonator configuration are as small as 3 cm by 3 cm.Power transmission efficiency of greater than 80%is achieved with a power transmission distance smaller than 5 mm via the strong coupling between two loop resonators around 1 GHz,as demonstrated by simulations and measurements.Experimental results also show that the power transmission performance is insensitive to various geometrical misalignments.The numerical and experimental results of this paper reveal a bandwidth of more than 50 MHz within which the power transmission efficiency is above 80%.As a result,the proposed microstrip loop resonator has the potential to accomplish efficient wireless power transmission and high-speed(higher than 10 Mbit/s)wireless communication simultaneously.
