A high-performance Ti-Ni-B alloy with good tensile properties and reduced mechanical anisotropy was developed by promoting the columnar to equiaxed transition(CET)of prior-βgrains and modifyingα-laths to equiaxed gr...A high-performance Ti-Ni-B alloy with good tensile properties and reduced mechanical anisotropy was developed by promoting the columnar to equiaxed transition(CET)of prior-βgrains and modifyingα-laths to equiaxed grains.Both Ni and B contributed to the refinement of columnar prior-βgrains during the L→βphase transformation by generating constitutional undercooling.Compared with Ni,B had a su-perior capability of generating constitutional undercooling,which not only replaced a significant amount of Ni with a minor addition to reduce the formation of brittle eutectoid,but also reacted with Ti to form TiB to promote heterogeneous nucleation ofα-Ti grains during theβ→αphase transformation.Together with the restricted growth ofα-laths induced by the refinement of prior-βgrains,a fully equiaxedα-Ti structure was obtained.The competition between the negative effect of brittle eutectoid and the positive role ofα-lath to equiaxed grain transition on the ductility of as-printed Ti-Ni-B alloys was fundamen-tally governed by the morphology of eutectoid and technically dependent on the Ni-B content.When the addition was 1.2Ni-0.06B(wt.%)or less,the positive effect ofα-lath on equiaxed grain transition can effectively mitigate the issue of reduced ductility caused by brittle eutectoid.In contrast,at 1.8Ni-0.09B or greater,the negative effect of eutectoid dominated.New insights into microstructural design obtained through the aforementioned approach were presented and discussed.展开更多
TiAI-based alloys with various compositions (including Ti-48Al, Ti-47Al-2Cr-2Nb, Ti-47Al-2Cr-2Nb-0.2B and Ti-47Al-3Cr, in mole fraction) had been prepared by elemental powder metallurgy (EPM). The results have shown t...TiAI-based alloys with various compositions (including Ti-48Al, Ti-47Al-2Cr-2Nb, Ti-47Al-2Cr-2Nb-0.2B and Ti-47Al-3Cr, in mole fraction) had been prepared by elemental powder metallurgy (EPM). The results have shown that the density of the prepared Ti-48AI alloy increases with increasing hot pressing temperature up to 1300℃. The Ti-48AI alloy microstructure mainly consisted of island-like Ti3Al phase and TiAl matrix at hot pressing temperature below 1300℃, however, coarse α2/γ lamellar colonies and γ grains appeared at 1400℃. It has also indicated that the additions of elemental Cr and B can refine the alloy microstructure. The main microstructural inhomogeneity in EPM TiAI-based alloys was the island-like α2 phase or the aggregate of α2/γ lamellar colony, and such island-like structure will be inherited during subsequent heat treatment in (α＋γ) field. Only after heat treatment in a field would this structure be eliminated. The mechanical properties of EPM TiAl-based alloys with various compositions were tested, and the effect of alloy elements on the mechanical properties was closely related to that of alloy elements on the alloy microstructures. Based on the above results, TiAI-based alloy exhaust valves were fabricated by elemental powder metallurgy and diffusion joining. The automobile engine test had demonstrated that the performance of the manufactured valves was very promising for engine service.展开更多
The potential of powder metallurgy processing for the manufacture of Al?SrB6 composites was explored. Al4Sr particles fractured extensively during the ball milling of Al?15Sr/Al?4B powder mixtures. There was no intera...The potential of powder metallurgy processing for the manufacture of Al?SrB6 composites was explored. Al4Sr particles fractured extensively during the ball milling of Al?15Sr/Al?4B powder mixtures. There was no interaction between the Al4Sr and AlB2 compounds across the section of the aluminium grains in the as-milled state. SrB6 formed, when the ball milled powder blends were subsequently annealed at sufficiently high temperatures. Ball milling for 1 h was sufficient for SrB6 to become the major constituent in powder blends annealed at 700 °C while it took 2 h of ball milling for powder blends annealed at 600 °C. Higher annealing temperatures and longer ball milling time encouraged the formation of the SrB6 compound while the latter made a great impact on the microstructural features of the Al?SrB6 composite. The SrB6 compound particles were much smaller and more uniformly distributed across the aluminium matrix grains in powder grains ball milled for 2 h before the annealing treatments at 600 °C and 700 °C.展开更多
Multiphase CrMnFeCoNi high-entropy alloys(HEAs)were prepared by a powder metallurgy process com-bining mechanical alloying(MA)and vacuum hot-pressing sintering(HPS).The single-phase face-centered cubic(FCC)HEA powder ...Multiphase CrMnFeCoNi high-entropy alloys(HEAs)were prepared by a powder metallurgy process com-bining mechanical alloying(MA)and vacuum hot-pressing sintering(HPS).The single-phase face-centered cubic(FCC)HEA powder prepared by MA was sintered into a bulk HEA specimen containing FCC phase matrix along with precipitated M 23 C 6 phase and nanoscaleσphase particles.When the sintering temper-ature was 1223 K,the ultimate strength reaches 1300±11.6 MPa,and the elongation exceeds 4%±0.6%.Microstructural characterization reveals that the formation of nanoscale particles and deformation twins play critical roles in improving the strain hardening(SH)ability.Prolonging the MA time promoted the formation of the precipitated phase and enhanced the SH ability by increasing the number of precip-itated particles.The SH capacity increases significantly with increasing sintering temperature,which is attributed to a significant enhancement in the twinning capacity due to grain growth and the reduced number ofσphase particles.Through systematic studies,the planar glide of dislocations was found to be the main mode of deformation,while deformation twinning appeared as an auxiliary deformation mode when the twinning stress was reached.Although the formation of precipitates leads to grain bound-ary and precipitation strengthening effects,crack initiation is more prominent owing to increased grain boundary brittleness around the precipitated M 23 C 6 phase.The prominence of crack initiation is a contra-diction that must be reconciled with regard to precipitation strengthening.This work serves as a useful reference for the preparation of high-strength HEA parts by powder metallurgy.展开更多
Multiwalled carbon nanotubes (MWNTs) were treated with the reflux within the concentrated nitric acid for 0-25 h to purify and disperse the tangled MWNTs. The effect of reflux time on the morphology and the weight los...Multiwalled carbon nanotubes (MWNTs) were treated with the reflux within the concentrated nitric acid for 0-25 h to purify and disperse the tangled MWNTs. The effect of reflux time on the morphology and the weight loss of MWNTs were investigated. Meanwhile,the dispersion of MWNTs with 0-2.0 wt.% in 2024Al powders using mechanical stirring with an assisting ultrasonic shaker in ethanol was also studied. The results show that the reflux time markedly affects the morphology of MWNTs. The weight loss of MWNTs i...展开更多
Graphite flake/Cu composite has attracted tremendous attention as a promising heat sinks materials owing to its easy machinability and superior thermal properties. However, its preparation process still faces several ...Graphite flake/Cu composite has attracted tremendous attention as a promising heat sinks materials owing to its easy machinability and superior thermal properties. However, its preparation process still faces several technological limitations including complex, time-consuming and costly synthetic approaches. In this work, a facile and scalable intermittently electroplated method is applied to prepare Cu-coated graphite flake composite powders, which are subsequently sintered into dense composite bulks. The results show that the graphite flake is successfully coated with a uniform and compact Cu shell,which effectively inhibits the segregation accumulation of graphite flakes and contributes to homogeneous distribution of graphite in the sintered graphite flake/Cu composites. The as-sintered composites exhibit an excellent thermal conductivity of 710 W·m-1·K-1and an outstanding bending strength of 93 MPa. Such performance, together with the simple, efficient powder-preparation process, suggests that the present strategy may open up opportunities for the development of thermal management materials.展开更多
Porous metals are a class of cellular materials with lightweight and unique mechanical,electrical,thermal,physical and acoustic characteristics.Magnesium and magnesium alloy foams have exhibited excellent advantages.I...Porous metals are a class of cellular materials with lightweight and unique mechanical,electrical,thermal,physical and acoustic characteristics.Magnesium and magnesium alloy foams have exhibited excellent advantages.In particular,open-cell Mg-based foams(porous Mg/Mg alloy foams)have been used for bioresorbable implants,CO_(2)trapping systems,filters,heat exchangers,absorbent panels and many other applications.While significant progress has been taken in producing porous Mg-based foams with good structure-property relations,but with a large number of different processing parameters,different mechanical properties and pore morphologies of each porous Mg-based foam,it is essential to understand the individual effects of each aspect of the parameters.Therefore,the present article summarized the effects of available processing parameters on the structure and mechanical properties of the porous Mg-based foams.Finally,the future perspectives to enhance the structure and properties of porous Mg/Mg alloy foams were discussed.展开更多
Two kinds of high strength-damping aluminum alloys （LZ7） were fabricated by rapid solidification and powder metallurgy （RS-PM） process. One material was extruded to profile aluminum directly and the other was extr...Two kinds of high strength-damping aluminum alloys （LZ7） were fabricated by rapid solidification and powder metallurgy （RS-PM） process. One material was extruded to profile aluminum directly and the other was extruded to bar and then rolled to sheet. The damping capacity over a temperature range of 25-300 ℃was studied with damping mechanical thermal analyzer （DMTA） and the microstructures were investigated by optical microscopy （OM）, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The experimental results show that the damping capacity increases with the test temperature elevating. Internal friction value of rolled sheet aluminum is up to 11.5×10^-2 and that of profile aluminum is as high as 6.0×10^-2 and 7.5×10^-2 at 300 ℃, respectively. Microstructure analysis shows the shape of precipitation phase of rolled alloy is more regular and the distribution is more homogeneous than that of profile alloy. Meanwhile, the interface between particulate and matrix of rolled sheet alloy is looser than that of profile alloy. Maybe the differences at interface can explain why damping capacity of rolled sheet alloy is higher than that of profile alloys at high temperature （above 120 ℃）.展开更多
A new technique, powder compact foaming process for the production of aluminumfoams has been studied in this article. According to this method, the aluminum pow-der is mixed with a powder foaming agent (TiH_2). Subseq...A new technique, powder compact foaming process for the production of aluminumfoams has been studied in this article. According to this method, the aluminum pow-der is mixed with a powder foaming agent (TiH_2). Subsequent to mixing, the powderblend is hot compacted to obtain a dense semi--finished product. Upon heating to tem-peratures within the range of the melting point, the foaming agent decomposes to evolvegas and the semi--finished product expands into a porous cellular aluminum. Foamingprocess is the key in this method. Based on experiments, the foaming characteris-tics were mainly analyzed and discussed. Experiments show that the aluminum--foamwith closed pores and a uniform cell structure of high porosity can be obtained usingthis method by adjusting the foaming parameters: the content of foaming agent andfoaming temperature.展开更多
A hypereutectic Al-Si alloy powder was prepared by ultrasonic gas atomization process. The morphologies, microstructure and phase constituent of the alloy powder were studied. The results showed that powder of the all...A hypereutectic Al-Si alloy powder was prepared by ultrasonic gas atomization process. The morphologies, microstructure and phase constituent of the alloy powder were studied. The results showed that powder of the alloy was very fine and its microstructure was mainly consisted of Si crystals plus intermetallic compound A19FeSi3, which were.very fine and uniformly distributed.展开更多
To control the morphology and particle size of dense spherical molybdenum powder prepared by radio frequency（RF） plasma from irregular molybdenum powder as a precursor, plasma process parameters were optimized in th...To control the morphology and particle size of dense spherical molybdenum powder prepared by radio frequency（RF） plasma from irregular molybdenum powder as a precursor, plasma process parameters were optimized in this paper. The effects of the carrier gas flow rate and molybdenum powder feeding rate on the shape and size of the final products were studied. The molybdenum powder morphology was examined using high-resolution scanning electron microscopy. The powder phases were analyzed by X-ray diffraction. The tap density and apparent density of the molybdenum powder were investigated using a Hall flow meter and a Scott volumeter. The optimal process parameters for the spherical molybdenum powder preparation are 50 g/min powder feeding rate and 0.6 m^3/h carrier gas rate. In addition, pure spherical molybdenum powder can be obtained from irregular powder, and the tap density is enhanced after plasma processing. The average size is reduced from 72 to 62 μm, and the tap density is increased from 2.7 to 6.2 g/cm^3. Therefore, RF plasma is a promising method for the preparation of high-density and high-purity spherical powders.展开更多
This study described a hydrometallurgical method to investigate the separation of rare earth elements（REEs）from rare earth polishing powder wastes（REPPWs）containing large amounts of rare earth oxides with a major ...This study described a hydrometallurgical method to investigate the separation of rare earth elements（REEs）from rare earth polishing powder wastes（REPPWs）containing large amounts of rare earth oxides with a major phase of CeO2 and minor phases of La2O3,Pr2O3,and Nd2O3 using a process devised by the authors.The suggested approach consisted of five processes：the synthesis of NaR E（SO4）2·xH2O from rare earth oxides in Na2SO4-H2SO4-H2 O solutions（Process 1）,the conversion of NaR E（SO4）2·xH2O into RE（OH）3 using NaO H（Process 2）,and the oxidation of Ce（OH）3 into Ce（OH）4 using air with O2 injection（Process 3）,followed by Processes 4 and 5 for separation of REEs by acid leaching using HCl and H2SO4,respectively.To confirm the high yield of NaR E（SO4）2·xH2O in Process 1,experiments were carried out under various Na2SO4 concentrations（0.4–2.5 mol/L）,sulfuric acid concentrations（6–14 mol/L）,and reaction temperatures（95–125 oC）.In addition,the effect of the pH value on the separation of Ce（OH）4 in HCl-H2 O solutions with Ce（OH）4,La-,Pr-,and Nd（OH）3 in Process 4 was also investigated.On the basis of above results,the possibility of effective separation of REEs from REPPWs could be confirmed.展开更多
The morphology and the formation of Y2BaCuO5 phase in powder melting processed YBa2Cu3O7-x superconductors were investigated. The experimental results show the heat treatment can not change the shape of Y2BaCuO5 parti...The morphology and the formation of Y2BaCuO5 phase in powder melting processed YBa2Cu3O7-x superconductors were investigated. The experimental results show the heat treatment can not change the shape of Y2BaCuO5 particles in powder melting processed samples. The formation of round Y2BaCuO5 phase is due to relative content of each constitution of precursor powders in powder melting process. For powder melting process, the excessive liquid phase is eliminated, which restrains the preferred growth of Y2BaCuO5 particles.展开更多
Strontium bismuth tantalum (SBT) fine power was prepared by Sol-Gel method. Pentaethoxy tantalum, strontium acetate and bismuth subnitrate were used as raw materials, and were dissolved in proper order in ethylene gl...Strontium bismuth tantalum (SBT) fine power was prepared by Sol-Gel method. Pentaethoxy tantalum, strontium acetate and bismuth subnitrate were used as raw materials, and were dissolved in proper order in ethylene glycol to form transparent sol. The mixed precursor was dried at 80℃ and annealed at 800℃ for 1 h. Crystallized nanometer sized SBT fine powder was obtained and characterized by XRD.展开更多
Compaction processes are one the most important par ts of powder forming technology. The main applications are focused on pieces for a utomotive, aeronautic, electric and electronic industries. The main goals of the c...Compaction processes are one the most important par ts of powder forming technology. The main applications are focused on pieces for a utomotive, aeronautic, electric and electronic industries. The main goals of the compaction processes are to obtain a compact with the geometrical requirements, without cracks, and with a uniform distribution of density. Design of such proc esses consist, essentially, in determine the sequence and relative displacements of die and punches in order to achieve such goals. A.B. Khoei presented a gener al framework for the finite element simulation of powder forming processes based on the following aspects; a large displacement formulation, centred on a total and updated Lagrangian formulation; an adaptive finite element strategy based on error estimates and automatic remeshing techniques; a cap model based on a hard ening rule in modelling of the highly non-linear behaviour of material; and the use of an efficient contact algorithm in the context of an interface element fo rmulation. In these references, the non-linear behaviour of powder was adequately desc ribed by the cap plasticity model. However, it suffers from a serious deficiency when the stress-point reaches a yield surface. In the flow theory of plasticit y, the transition from an elastic state to an elasto-plastic state appears more or less abruptly. For powder material it is very difficult to define the locati on of yield surface, because there is no distinct transition from elastic to ela stic-plastic behaviour. Results of experimental test on some hard met al powder show that the plastic effects were begun immediately upon loading. In such mater ials the domain of the yield surface would collapse to a point, so making the di rection of plastic increment indeterminate, because all directions are normal to a point. Thus, the classical plasticity theory cannot deal with such materials and an advanced constitutive theory is necessary. In the present paper, the constitutive equations of powder materials will be discussed via an endochronic theory of plasticity. This theory provides a unifi ed point of view to describe the elastic-plastic behaviour of material since it places no requirement for a yield surface and a ’loading function’ to disting uish between loading an unloading. Endochronic theory of plasticity has been app lied to a number of metallic materials, concrete and sand, but to the knowledge of authors, no numerical scheme of the model has been applied to powder material . In the present paper, a new approach is developed based on an endochronic rate independent, density-dependent plasticity model for describing the isothermal deformation behavior of metal powder at low homologous temperature. Although the concept of yield surface has not been explicitly assumed in endochronic theory, it is shown that the cone-cap plasticity yield surface (Fig.1), which is the m ost commonly used plasticity models for describing the behavior of powder materi al can be easily derived as a special case of the proposed endochronic theory. Fig.1 Trace of cone-cap yield function on the meridian pl ane for different relative density As large deformation is observed in powder compaction process, a hypoelastic-pl astic formulation is developed in the context of finite deformation plasticity. Constitutive equations are stated in unrotated frame of reference that greatly s implifies endochronic constitutive relation in finite plasticity. Constitutive e quations of the endochronic theory and their numerical integration are establish ed and procedures for determining material parameters of the model are demonstra ted. Finally, the numerical schemes are examined for efficiency in the model ling of a tip shaped component, as shown in Fig.2. Fig.2 A shaped tip component. a) Geometry, boundary conditio n and finite element mesh; b) density distribution at final stage of展开更多
As computer simulation increasingly supports engine er ing design and manufacture, the requirement for a computer software environment providing an integration platform for computational engineering software increas e...As computer simulation increasingly supports engine er ing design and manufacture, the requirement for a computer software environment providing an integration platform for computational engineering software increas es. A key component of an integrated environment is the use of computational eng ineering to assist and support solutions for complex design. Computer methods fo r structural, flow and thermal analysis are well developed and have been used in design for many years. Many software packages are now available which provi de an advanced capability. However, they are not designed for modelling of powde r forming processes. This paper describes the powder compaction software (PCS_SU T), which is designed for pre- and post-processing for computational simulatio n of the process compaction of powder. In the PCS_SUT software, the adaptive analysis of transient metal powder forming process is simulated by the finite element method based on deformation theories . The error estimates and adaptive remeshing schemes are applied for updated co -ordinate analysis. A generalized Newmark scheme is used for the time domain di scretization and the final nonlinear equations are solved by a Newton-Raphson p rocedure. An incremental elasto-plastic material model is used to simulate the compaction process. To describe the constitutive model of nonlinear behaviour of powder materials, a combination of Mohr-Coulomb and elliptical yield cap model is applied. This model reflects the yielding, frictional and densification char acteristics of powder along with strain and geometrical hardening which occurs d uring the compaction process. A hardening rule is used to define the dependence of the yield surface on the degree of plastic straining. A plasticity theory for friction is employed in the treatment of the powder-tooling interface. The inv olvement of two different materials, which have contact and relative movement in relation to each other, must be considered. A special formulation for friction modelling is coupled with a material formulation. The interface behaviour betwee n the die and the powder is modelled by using an interface element mesh. In the present paper, we have demonstrated pre- and post-processor finite elem ent software, written in Visual Basic, to generate the graphical model and visua lly display the computed results. The software consist of three main part: · Pre-processor: It is used to create the model, generate an app ropriate finite element grid, apply the appropriate boundary conditions, and vie w the total model. The geometric model can be used to associate the mesh with th e physical attributes such as element properties, material properties, or loads and boundary conditions. · Analysis: It can deal with two-dimensional and axi-symmetric applications for linear and non-linear behaviour of material in static and dyna mic analyses. Both triangular and quadrilateral elements are available in the e lement library, including 3-noded, 6-noded and 7-noded (T6B1) triangles and 4 -noded, 8-noded and 9-noded quadrilaterals. The direct implicit algorithm bas ed on the generalized Newmark scheme is used for the time integration and an aut omatic time step control facility is provided. For non-linear iteration, choice s among fully or modified Newton-Raphson method and quasi-Newton method, using the initial stiffness method, Davidon inverse method or BFGS inverse method, ar e possible. · Post-processor: It provides visualization of the computed resu lts, when the finite element model and analysis have been completed. Post-proce ssing is vital to allow the appropriate interpretation of the completed results of the finite element analysis. It provides the visual means to interpret the va st amounts of computed results generated. Finally, the powder behaviour during the compaction of a multi-level component is numerically simulated by the PCS_SUT software, as shown in Fig.1. The predict ive compaction forces at different displacements are computed and compared with the available experimental展开更多
Lunar surface additive manufacturing with lunar regolith is a key step in in-situ resource utilization.The powder spreading process is the key process,which has a major impact on the quality of the powder bed and the ...Lunar surface additive manufacturing with lunar regolith is a key step in in-situ resource utilization.The powder spreading process is the key process,which has a major impact on the quality of the powder bed and the precision of molded parts.In this study,the discrete element method(DEM)was adopted to simulate the powder spreading process with a roller.The three powder bed quality indicators,including the molding layer offset,voidage fraction,and surface roughness,were established.Besides,the influence of the three process parameters,which are roller’s translational speed,rotational speed,and powder spreading layer thickness on the powder bed quality indicators was also analyzed.The results show that with the reduction of the powder spreading layer thickness and the increase of the rotational speed,the offset increased significantly;when the translational speed increased,the offset first increased and then decreased,which resulted in an extreme value;with the increase of the layer thickness and the decrease of the translational speed,the values for voidage fraction and surface roughness significantly reduced.The powder bed quality indicators were adopted as the optimization objective,and the multi-objective parameter optimization was carried out.The predicted optimal powder spreading parameters and powder bed quality indicators were then obtained.Moreover,the optimal values were then verified.This study can provide informative guidance for in-situ manufacturing at the moon in future deep space exploration missions.展开更多
Red-emission （Y0.95Eu0.05）2O3 submicron spheres and microplates were selectively obtained via hydrothermal precursor synthesis （150 °C, 12 h） followed by calcination at 1000 °C. Characterizations of the ...Red-emission （Y0.95Eu0.05）2O3 submicron spheres and microplates were selectively obtained via hydrothermal precursor synthesis （150 °C, 12 h） followed by calcination at 1000 °C. Characterizations of the products were carried out by combined means of XRD, FT-IR, FE-SEM and PL analysis. The precursors could be modulated from basic-carbonate submicron spheres to normal carbonate microplates by increasing the molar ratio of urea to Y＋Eu from 10 to 40-100. The resultant oxides largely retain their respective precursor morphologies at 1000 °C, but morphology confined crystal growth was observed for the microplates, yielding more enhanced exposure of the （400） facets. Both the （Y0.95Eu0.05）2O3 spheres and microplates exhibit nearly identical positions of the PL bands and similar asymmetry factors of luminescence [I（5D0→7F2）/I（5D0→7F1）, ～11] under 250 nm excitation, but the microplates show a significantly strong red emission at ～613 nm （ ～1.33 times that of the spheres） owing to their larger particle size and denser packing of primary phosphor crystallites.展开更多
In the endeavor to maximize the refinement effect of primary Si and alleviate the inherent brittleness of hypereutectic Al-Si alloy,the approach of coating P as a modifier on powder was adopted.The ultimate aim was to...In the endeavor to maximize the refinement effect of primary Si and alleviate the inherent brittleness of hypereutectic Al-Si alloy,the approach of coating P as a modifier on powder was adopted.The ultimate aim was to create more heterogeneous fine Al P nucleus and enhance the nucleation efficiency of primary Si on Al P to refine the coarse primary Si to nano-scale during 3D printing.In the combination of large undercooling and high density of nucleation sites,the size of primary Si was successfully refined to 200–300 nm and the divorced eutectic was also induced to modify the microstructure of matrix.In the presence of nano-scale primary Si,the melting pool boundary(MPB)feature disappeared and the fracture mechanism also changed from load transfer to interfacial fracture.Compared with the pristine alloy,the ductility was increased four times without significantly changing the ultimate tensile strength(UTS)and wear resistance.The improvement of ductility is attributed to the refinement of primary Si,the disappearance of MPB features and the formation of divorced eutectic.The optimal tensile properties were:UTS-482 MPa,yield strength-320 MPa and ductility of 8.1%at 0.05 wt.%P.These are comparable to those for high-strength Al alloys.展开更多
Homogeneous co-precipitation and hydrothermal treatment were used to prepare nano- and highly dispersed Ni O/YSZ(yttria-stabilized zirconia) composite powders. Composite powders of size less than 100 nm were successfu...Homogeneous co-precipitation and hydrothermal treatment were used to prepare nano- and highly dispersed Ni O/YSZ(yttria-stabilized zirconia) composite powders. Composite powders of size less than 100 nm were successfully prepared. This process did not require separate sintering of the YSZ and Ni O to be used as the raw materials for solid oxide fuel cells. The performance of a cell fabricated using the new powders(max.power density ~0.87 W/cm^2) was higher than that of a cell fabricated using conventional powders(max. power density ~0.73 W/cm^2). Co-precipitation and hydrothermal treatment proved to be very effective processes for reducing cell production costs as well as improving cell performance.展开更多
基金This work was supported by the National Natural Science Foun-dation of China(Nos.52074254,51874271,and 52174349)the Key Projects of International Cooperation(No.122111KYSB20200034)+3 种基金the Project of Key Laboratory of Science and Technology on Par-ticle Materials(No.CXJJ-22S043)the CAS Project for Young Scientists in Basic Research(No.YSBR-025)This work was finan-cially supported by the Selection of Best Candidates to Undertake Key Research Projects(No.211110230200)This research work was also financially supported by the OU Master Plan Implementation Project promoted under Osaka University.
文摘A high-performance Ti-Ni-B alloy with good tensile properties and reduced mechanical anisotropy was developed by promoting the columnar to equiaxed transition(CET)of prior-βgrains and modifyingα-laths to equiaxed grains.Both Ni and B contributed to the refinement of columnar prior-βgrains during the L→βphase transformation by generating constitutional undercooling.Compared with Ni,B had a su-perior capability of generating constitutional undercooling,which not only replaced a significant amount of Ni with a minor addition to reduce the formation of brittle eutectoid,but also reacted with Ti to form TiB to promote heterogeneous nucleation ofα-Ti grains during theβ→αphase transformation.Together with the restricted growth ofα-laths induced by the refinement of prior-βgrains,a fully equiaxedα-Ti structure was obtained.The competition between the negative effect of brittle eutectoid and the positive role ofα-lath to equiaxed grain transition on the ductility of as-printed Ti-Ni-B alloys was fundamen-tally governed by the morphology of eutectoid and technically dependent on the Ni-B content.When the addition was 1.2Ni-0.06B(wt.%)or less,the positive effect ofα-lath on equiaxed grain transition can effectively mitigate the issue of reduced ductility caused by brittle eutectoid.In contrast,at 1.8Ni-0.09B or greater,the negative effect of eutectoid dominated.New insights into microstructural design obtained through the aforementioned approach were presented and discussed.
基金the National Natural Science Foundation of China (Project 59895150) and the National Advanced Materials Committee (Project 7
文摘TiAI-based alloys with various compositions (including Ti-48Al, Ti-47Al-2Cr-2Nb, Ti-47Al-2Cr-2Nb-0.2B and Ti-47Al-3Cr, in mole fraction) had been prepared by elemental powder metallurgy (EPM). The results have shown that the density of the prepared Ti-48AI alloy increases with increasing hot pressing temperature up to 1300℃. The Ti-48AI alloy microstructure mainly consisted of island-like Ti3Al phase and TiAl matrix at hot pressing temperature below 1300℃, however, coarse α2/γ lamellar colonies and γ grains appeared at 1400℃. It has also indicated that the additions of elemental Cr and B can refine the alloy microstructure. The main microstructural inhomogeneity in EPM TiAI-based alloys was the island-like α2 phase or the aggregate of α2/γ lamellar colony, and such island-like structure will be inherited during subsequent heat treatment in (α＋γ) field. Only after heat treatment in a field would this structure be eliminated. The mechanical properties of EPM TiAl-based alloys with various compositions were tested, and the effect of alloy elements on the mechanical properties was closely related to that of alloy elements on the alloy microstructures. Based on the above results, TiAI-based alloy exhaust valves were fabricated by elemental powder metallurgy and diffusion joining. The automobile engine test had demonstrated that the performance of the manufactured valves was very promising for engine service.
文摘The potential of powder metallurgy processing for the manufacture of Al?SrB6 composites was explored. Al4Sr particles fractured extensively during the ball milling of Al?15Sr/Al?4B powder mixtures. There was no interaction between the Al4Sr and AlB2 compounds across the section of the aluminium grains in the as-milled state. SrB6 formed, when the ball milled powder blends were subsequently annealed at sufficiently high temperatures. Ball milling for 1 h was sufficient for SrB6 to become the major constituent in powder blends annealed at 700 °C while it took 2 h of ball milling for powder blends annealed at 600 °C. Higher annealing temperatures and longer ball milling time encouraged the formation of the SrB6 compound while the latter made a great impact on the microstructural features of the Al?SrB6 composite. The SrB6 compound particles were much smaller and more uniformly distributed across the aluminium matrix grains in powder grains ball milled for 2 h before the annealing treatments at 600 °C and 700 °C.
基金supported by the National Natu-ral Science Foundation of China(Nos.52061021,51861016,and 51871132)the Science and Technology Major Project of Yun-nan Province(Nos.202202AG050004,202002AB080001)+2 种基金the Young and Middle-Aged Academic and Technical Leaders Reserve Talent Project(No.202005AC160039)support by the Ministry of Science and Higher Educa-tion of the Russian Federation in the framework of the Increase Competitiveness Program of NUST«MISiS»(No.K2-2020-046)financial support from the China Scholarship Council(CSC,No.201906220226).
文摘Multiphase CrMnFeCoNi high-entropy alloys(HEAs)were prepared by a powder metallurgy process com-bining mechanical alloying(MA)and vacuum hot-pressing sintering(HPS).The single-phase face-centered cubic(FCC)HEA powder prepared by MA was sintered into a bulk HEA specimen containing FCC phase matrix along with precipitated M 23 C 6 phase and nanoscaleσphase particles.When the sintering temper-ature was 1223 K,the ultimate strength reaches 1300±11.6 MPa,and the elongation exceeds 4%±0.6%.Microstructural characterization reveals that the formation of nanoscale particles and deformation twins play critical roles in improving the strain hardening(SH)ability.Prolonging the MA time promoted the formation of the precipitated phase and enhanced the SH ability by increasing the number of precip-itated particles.The SH capacity increases significantly with increasing sintering temperature,which is attributed to a significant enhancement in the twinning capacity due to grain growth and the reduced number ofσphase particles.Through systematic studies,the planar glide of dislocations was found to be the main mode of deformation,while deformation twinning appeared as an auxiliary deformation mode when the twinning stress was reached.Although the formation of precipitates leads to grain bound-ary and precipitation strengthening effects,crack initiation is more prominent owing to increased grain boundary brittleness around the precipitated M 23 C 6 phase.The prominence of crack initiation is a contra-diction that must be reconciled with regard to precipitation strengthening.This work serves as a useful reference for the preparation of high-strength HEA parts by powder metallurgy.
文摘Multiwalled carbon nanotubes (MWNTs) were treated with the reflux within the concentrated nitric acid for 0-25 h to purify and disperse the tangled MWNTs. The effect of reflux time on the morphology and the weight loss of MWNTs were investigated. Meanwhile,the dispersion of MWNTs with 0-2.0 wt.% in 2024Al powders using mechanical stirring with an assisting ultrasonic shaker in ethanol was also studied. The results show that the reflux time markedly affects the morphology of MWNTs. The weight loss of MWNTs i...
基金financially supported by the National Key Research and Development Program of China(No.2016YFC0700905)the National Natural Science Foundation of China(Grant No.51674232,No.51972304 and No.51702331)。
文摘Graphite flake/Cu composite has attracted tremendous attention as a promising heat sinks materials owing to its easy machinability and superior thermal properties. However, its preparation process still faces several technological limitations including complex, time-consuming and costly synthetic approaches. In this work, a facile and scalable intermittently electroplated method is applied to prepare Cu-coated graphite flake composite powders, which are subsequently sintered into dense composite bulks. The results show that the graphite flake is successfully coated with a uniform and compact Cu shell,which effectively inhibits the segregation accumulation of graphite flakes and contributes to homogeneous distribution of graphite in the sintered graphite flake/Cu composites. The as-sintered composites exhibit an excellent thermal conductivity of 710 W·m-1·K-1and an outstanding bending strength of 93 MPa. Such performance, together with the simple, efficient powder-preparation process, suggests that the present strategy may open up opportunities for the development of thermal management materials.
基金supported by the Natural Science Foundation of Jiangsu Province of China(Grant No.BK20171437)Key R&D Program of Jiangsu Province of China(Grant No.BE2018044)+2 种基金the Guiding Captital for Industry Development Project of Suqian of China(Grant No.H201714)the Basic Science Research Project of Nantong of China(Grant No.JC2021190)the Natural Science Foundation of China(Grant No.12072105).
文摘Porous metals are a class of cellular materials with lightweight and unique mechanical,electrical,thermal,physical and acoustic characteristics.Magnesium and magnesium alloy foams have exhibited excellent advantages.In particular,open-cell Mg-based foams(porous Mg/Mg alloy foams)have been used for bioresorbable implants,CO_(2)trapping systems,filters,heat exchangers,absorbent panels and many other applications.While significant progress has been taken in producing porous Mg-based foams with good structure-property relations,but with a large number of different processing parameters,different mechanical properties and pore morphologies of each porous Mg-based foam,it is essential to understand the individual effects of each aspect of the parameters.Therefore,the present article summarized the effects of available processing parameters on the structure and mechanical properties of the porous Mg-based foams.Finally,the future perspectives to enhance the structure and properties of porous Mg/Mg alloy foams were discussed.
基金Project (50971012) supported by the National Natural Science Foundation of China
文摘Two kinds of high strength-damping aluminum alloys （LZ7） were fabricated by rapid solidification and powder metallurgy （RS-PM） process. One material was extruded to profile aluminum directly and the other was extruded to bar and then rolled to sheet. The damping capacity over a temperature range of 25-300 ℃was studied with damping mechanical thermal analyzer （DMTA） and the microstructures were investigated by optical microscopy （OM）, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The experimental results show that the damping capacity increases with the test temperature elevating. Internal friction value of rolled sheet aluminum is up to 11.5×10^-2 and that of profile aluminum is as high as 6.0×10^-2 and 7.5×10^-2 at 300 ℃, respectively. Microstructure analysis shows the shape of precipitation phase of rolled alloy is more regular and the distribution is more homogeneous than that of profile alloy. Meanwhile, the interface between particulate and matrix of rolled sheet alloy is looser than that of profile alloy. Maybe the differences at interface can explain why damping capacity of rolled sheet alloy is higher than that of profile alloys at high temperature （above 120 ℃）.
文摘A new technique, powder compact foaming process for the production of aluminumfoams has been studied in this article. According to this method, the aluminum pow-der is mixed with a powder foaming agent (TiH_2). Subsequent to mixing, the powderblend is hot compacted to obtain a dense semi--finished product. Upon heating to tem-peratures within the range of the melting point, the foaming agent decomposes to evolvegas and the semi--finished product expands into a porous cellular aluminum. Foamingprocess is the key in this method. Based on experiments, the foaming characteris-tics were mainly analyzed and discussed. Experiments show that the aluminum--foamwith closed pores and a uniform cell structure of high porosity can be obtained usingthis method by adjusting the foaming parameters: the content of foaming agent andfoaming temperature.
基金This work has been supported by the Flu,tda~ion Of harbin institute of Technology for Out standing YOungScientists (No. 1832).
文摘A hypereutectic Al-Si alloy powder was prepared by ultrasonic gas atomization process. The morphologies, microstructure and phase constituent of the alloy powder were studied. The results showed that powder of the alloy was very fine and its microstructure was mainly consisted of Si crystals plus intermetallic compound A19FeSi3, which were.very fine and uniformly distributed.
基金financially supported by the 2012 Western Materials Innovation Foundation of China (No. XBCL-1-06)the Science and Technology Coordinating Innovative Engineering Project of Shaanxi Province of China (No. 2014KTCQ01-35)+1 种基金the Natural Science Foundation of Shaanxi Province of China (No. 2014JM6226)the Specialized Research Fund of Education Commission of Shaanxi Province of China (No. 2013JK0905)
文摘To control the morphology and particle size of dense spherical molybdenum powder prepared by radio frequency（RF） plasma from irregular molybdenum powder as a precursor, plasma process parameters were optimized in this paper. The effects of the carrier gas flow rate and molybdenum powder feeding rate on the shape and size of the final products were studied. The molybdenum powder morphology was examined using high-resolution scanning electron microscopy. The powder phases were analyzed by X-ray diffraction. The tap density and apparent density of the molybdenum powder were investigated using a Hall flow meter and a Scott volumeter. The optimal process parameters for the spherical molybdenum powder preparation are 50 g/min powder feeding rate and 0.6 m^3/h carrier gas rate. In addition, pure spherical molybdenum powder can be obtained from irregular powder, and the tap density is enhanced after plasma processing. The average size is reduced from 72 to 62 μm, and the tap density is increased from 2.7 to 6.2 g/cm^3. Therefore, RF plasma is a promising method for the preparation of high-density and high-purity spherical powders.
文摘This study described a hydrometallurgical method to investigate the separation of rare earth elements（REEs）from rare earth polishing powder wastes（REPPWs）containing large amounts of rare earth oxides with a major phase of CeO2 and minor phases of La2O3,Pr2O3,and Nd2O3 using a process devised by the authors.The suggested approach consisted of five processes：the synthesis of NaR E（SO4）2·xH2O from rare earth oxides in Na2SO4-H2SO4-H2 O solutions（Process 1）,the conversion of NaR E（SO4）2·xH2O into RE（OH）3 using NaO H（Process 2）,and the oxidation of Ce（OH）3 into Ce（OH）4 using air with O2 injection（Process 3）,followed by Processes 4 and 5 for separation of REEs by acid leaching using HCl and H2SO4,respectively.To confirm the high yield of NaR E（SO4）2·xH2O in Process 1,experiments were carried out under various Na2SO4 concentrations（0.4–2.5 mol/L）,sulfuric acid concentrations（6–14 mol/L）,and reaction temperatures（95–125 oC）.In addition,the effect of the pH value on the separation of Ce（OH）4 in HCl-H2 O solutions with Ce（OH）4,La-,Pr-,and Nd（OH）3 in Process 4 was also investigated.On the basis of above results,the possibility of effective separation of REEs from REPPWs could be confirmed.
基金Funded by the National Natural Science Foundation of China (50432050)the National High Technology Research and Development Program of China(2007AA03Z241)
文摘The morphology and the formation of Y2BaCuO5 phase in powder melting processed YBa2Cu3O7-x superconductors were investigated. The experimental results show the heat treatment can not change the shape of Y2BaCuO5 particles in powder melting processed samples. The formation of round Y2BaCuO5 phase is due to relative content of each constitution of precursor powders in powder melting process. For powder melting process, the excessive liquid phase is eliminated, which restrains the preferred growth of Y2BaCuO5 particles.
文摘Strontium bismuth tantalum (SBT) fine power was prepared by Sol-Gel method. Pentaethoxy tantalum, strontium acetate and bismuth subnitrate were used as raw materials, and were dissolved in proper order in ethylene glycol to form transparent sol. The mixed precursor was dried at 80℃ and annealed at 800℃ for 1 h. Crystallized nanometer sized SBT fine powder was obtained and characterized by XRD.
文摘Compaction processes are one the most important par ts of powder forming technology. The main applications are focused on pieces for a utomotive, aeronautic, electric and electronic industries. The main goals of the compaction processes are to obtain a compact with the geometrical requirements, without cracks, and with a uniform distribution of density. Design of such proc esses consist, essentially, in determine the sequence and relative displacements of die and punches in order to achieve such goals. A.B. Khoei presented a gener al framework for the finite element simulation of powder forming processes based on the following aspects; a large displacement formulation, centred on a total and updated Lagrangian formulation; an adaptive finite element strategy based on error estimates and automatic remeshing techniques; a cap model based on a hard ening rule in modelling of the highly non-linear behaviour of material; and the use of an efficient contact algorithm in the context of an interface element fo rmulation. In these references, the non-linear behaviour of powder was adequately desc ribed by the cap plasticity model. However, it suffers from a serious deficiency when the stress-point reaches a yield surface. In the flow theory of plasticit y, the transition from an elastic state to an elasto-plastic state appears more or less abruptly. For powder material it is very difficult to define the locati on of yield surface, because there is no distinct transition from elastic to ela stic-plastic behaviour. Results of experimental test on some hard met al powder show that the plastic effects were begun immediately upon loading. In such mater ials the domain of the yield surface would collapse to a point, so making the di rection of plastic increment indeterminate, because all directions are normal to a point. Thus, the classical plasticity theory cannot deal with such materials and an advanced constitutive theory is necessary. In the present paper, the constitutive equations of powder materials will be discussed via an endochronic theory of plasticity. This theory provides a unifi ed point of view to describe the elastic-plastic behaviour of material since it places no requirement for a yield surface and a ’loading function’ to disting uish between loading an unloading. Endochronic theory of plasticity has been app lied to a number of metallic materials, concrete and sand, but to the knowledge of authors, no numerical scheme of the model has been applied to powder material . In the present paper, a new approach is developed based on an endochronic rate independent, density-dependent plasticity model for describing the isothermal deformation behavior of metal powder at low homologous temperature. Although the concept of yield surface has not been explicitly assumed in endochronic theory, it is shown that the cone-cap plasticity yield surface (Fig.1), which is the m ost commonly used plasticity models for describing the behavior of powder materi al can be easily derived as a special case of the proposed endochronic theory. Fig.1 Trace of cone-cap yield function on the meridian pl ane for different relative density As large deformation is observed in powder compaction process, a hypoelastic-pl astic formulation is developed in the context of finite deformation plasticity. Constitutive equations are stated in unrotated frame of reference that greatly s implifies endochronic constitutive relation in finite plasticity. Constitutive e quations of the endochronic theory and their numerical integration are establish ed and procedures for determining material parameters of the model are demonstra ted. Finally, the numerical schemes are examined for efficiency in the model ling of a tip shaped component, as shown in Fig.2. Fig.2 A shaped tip component. a) Geometry, boundary conditio n and finite element mesh; b) density distribution at final stage of
文摘As computer simulation increasingly supports engine er ing design and manufacture, the requirement for a computer software environment providing an integration platform for computational engineering software increas es. A key component of an integrated environment is the use of computational eng ineering to assist and support solutions for complex design. Computer methods fo r structural, flow and thermal analysis are well developed and have been used in design for many years. Many software packages are now available which provi de an advanced capability. However, they are not designed for modelling of powde r forming processes. This paper describes the powder compaction software (PCS_SU T), which is designed for pre- and post-processing for computational simulatio n of the process compaction of powder. In the PCS_SUT software, the adaptive analysis of transient metal powder forming process is simulated by the finite element method based on deformation theories . The error estimates and adaptive remeshing schemes are applied for updated co -ordinate analysis. A generalized Newmark scheme is used for the time domain di scretization and the final nonlinear equations are solved by a Newton-Raphson p rocedure. An incremental elasto-plastic material model is used to simulate the compaction process. To describe the constitutive model of nonlinear behaviour of powder materials, a combination of Mohr-Coulomb and elliptical yield cap model is applied. This model reflects the yielding, frictional and densification char acteristics of powder along with strain and geometrical hardening which occurs d uring the compaction process. A hardening rule is used to define the dependence of the yield surface on the degree of plastic straining. A plasticity theory for friction is employed in the treatment of the powder-tooling interface. The inv olvement of two different materials, which have contact and relative movement in relation to each other, must be considered. A special formulation for friction modelling is coupled with a material formulation. The interface behaviour betwee n the die and the powder is modelled by using an interface element mesh. In the present paper, we have demonstrated pre- and post-processor finite elem ent software, written in Visual Basic, to generate the graphical model and visua lly display the computed results. The software consist of three main part: · Pre-processor: It is used to create the model, generate an app ropriate finite element grid, apply the appropriate boundary conditions, and vie w the total model. The geometric model can be used to associate the mesh with th e physical attributes such as element properties, material properties, or loads and boundary conditions. · Analysis: It can deal with two-dimensional and axi-symmetric applications for linear and non-linear behaviour of material in static and dyna mic analyses. Both triangular and quadrilateral elements are available in the e lement library, including 3-noded, 6-noded and 7-noded (T6B1) triangles and 4 -noded, 8-noded and 9-noded quadrilaterals. The direct implicit algorithm bas ed on the generalized Newmark scheme is used for the time integration and an aut omatic time step control facility is provided. For non-linear iteration, choice s among fully or modified Newton-Raphson method and quasi-Newton method, using the initial stiffness method, Davidon inverse method or BFGS inverse method, ar e possible. · Post-processor: It provides visualization of the computed resu lts, when the finite element model and analysis have been completed. Post-proce ssing is vital to allow the appropriate interpretation of the completed results of the finite element analysis. It provides the visual means to interpret the va st amounts of computed results generated. Finally, the powder behaviour during the compaction of a multi-level component is numerically simulated by the PCS_SUT software, as shown in Fig.1. The predict ive compaction forces at different displacements are computed and compared with the available experimental
文摘Lunar surface additive manufacturing with lunar regolith is a key step in in-situ resource utilization.The powder spreading process is the key process,which has a major impact on the quality of the powder bed and the precision of molded parts.In this study,the discrete element method(DEM)was adopted to simulate the powder spreading process with a roller.The three powder bed quality indicators,including the molding layer offset,voidage fraction,and surface roughness,were established.Besides,the influence of the three process parameters,which are roller’s translational speed,rotational speed,and powder spreading layer thickness on the powder bed quality indicators was also analyzed.The results show that with the reduction of the powder spreading layer thickness and the increase of the rotational speed,the offset increased significantly;when the translational speed increased,the offset first increased and then decreased,which resulted in an extreme value;with the increase of the layer thickness and the decrease of the translational speed,the values for voidage fraction and surface roughness significantly reduced.The powder bed quality indicators were adopted as the optimization objective,and the multi-objective parameter optimization was carried out.The predicted optimal powder spreading parameters and powder bed quality indicators were then obtained.Moreover,the optimal values were then verified.This study can provide informative guidance for in-situ manufacturing at the moon in future deep space exploration missions.
基金Projects (50172030, 50972025, 50990303, 51172038) supported by the National Natural Science Foundation of ChinaProject supported by the Liaoning BaiQianWan Talents Program, China+1 种基金Projects (N110802001, N100702001) supported by the Fundamental Research Funds for the Central Universities, ChinaProject supported by the China Scholarship Council
文摘Red-emission （Y0.95Eu0.05）2O3 submicron spheres and microplates were selectively obtained via hydrothermal precursor synthesis （150 °C, 12 h） followed by calcination at 1000 °C. Characterizations of the products were carried out by combined means of XRD, FT-IR, FE-SEM and PL analysis. The precursors could be modulated from basic-carbonate submicron spheres to normal carbonate microplates by increasing the molar ratio of urea to Y＋Eu from 10 to 40-100. The resultant oxides largely retain their respective precursor morphologies at 1000 °C, but morphology confined crystal growth was observed for the microplates, yielding more enhanced exposure of the （400） facets. Both the （Y0.95Eu0.05）2O3 spheres and microplates exhibit nearly identical positions of the PL bands and similar asymmetry factors of luminescence [I（5D0→7F2）/I（5D0→7F1）, ～11] under 250 nm excitation, but the microplates show a significantly strong red emission at ～613 nm （ ～1.33 times that of the spheres） owing to their larger particle size and denser packing of primary phosphor crystallites.
基金financially supported by the National Key Research and Development Program of China(No.2018YFB1105100)the Scientific Instrument Developing Project of the Chinese Academy of Sciences(No.YJKYYQ20190011)。
文摘In the endeavor to maximize the refinement effect of primary Si and alleviate the inherent brittleness of hypereutectic Al-Si alloy,the approach of coating P as a modifier on powder was adopted.The ultimate aim was to create more heterogeneous fine Al P nucleus and enhance the nucleation efficiency of primary Si on Al P to refine the coarse primary Si to nano-scale during 3D printing.In the combination of large undercooling and high density of nucleation sites,the size of primary Si was successfully refined to 200–300 nm and the divorced eutectic was also induced to modify the microstructure of matrix.In the presence of nano-scale primary Si,the melting pool boundary(MPB)feature disappeared and the fracture mechanism also changed from load transfer to interfacial fracture.Compared with the pristine alloy,the ductility was increased four times without significantly changing the ultimate tensile strength(UTS)and wear resistance.The improvement of ductility is attributed to the refinement of primary Si,the disappearance of MPB features and the formation of divorced eutectic.The optimal tensile properties were:UTS-482 MPa,yield strength-320 MPa and ductility of 8.1%at 0.05 wt.%P.These are comparable to those for high-strength Al alloys.
基金supported by Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Education, Science and Technology (2012R1A1A1013782)a fostering project funded by the Ministry of Education, Science and Technology (MEST)
文摘Homogeneous co-precipitation and hydrothermal treatment were used to prepare nano- and highly dispersed Ni O/YSZ(yttria-stabilized zirconia) composite powders. Composite powders of size less than 100 nm were successfully prepared. This process did not require separate sintering of the YSZ and Ni O to be used as the raw materials for solid oxide fuel cells. The performance of a cell fabricated using the new powders(max.power density ~0.87 W/cm^2) was higher than that of a cell fabricated using conventional powders(max. power density ~0.73 W/cm^2). Co-precipitation and hydrothermal treatment proved to be very effective processes for reducing cell production costs as well as improving cell performance.
