Weak water-drive offshore reservoirs with complex pore architecture and strong permeability heterogeneity present major challenges,including rapid depletion of formation energy,low waterflood efficiency,and significan...Weak water-drive offshore reservoirs with complex pore architecture and strong permeability heterogeneity present major challenges,including rapid depletion of formation energy,low waterflood efficiency,and significant lateral and vertical variability in crude oil properties,all of which contribute to limited recovery.To support more effective field development,alternative strategies and a deeper understanding of pore-scale flow behavior are urgently needed.In this work,CT imaging and digital image processing were used to construct a digital rock model representative of the target reservoir.A pore-scale flow model was then developed,and the Volume of Fluid(VOF)method was applied to simulate and optimize waterflooding schemes aimed at boosting oil recovery.Optimization focused on adjusting injection rates,varying the oil–water viscosity ratio,and implementing a water-alternating-gas(WAG)process.Results show that,for equal injection volumes,higher injection rates cause early water breakthrough through high-permeability pathways,yielding slower gains in recovery.Lowering the oil–water viscosity ratio improves mobility control,suppresses viscous fingering,enlarges sweep volume,and enhances recovery.When CH_(4)becomes fully miscible,it dissolves into the crude oil,lowering viscosity and eliminating interfacial tension,thereby providing greater displacement efficiency than partially miscible injection.Following a switch from water to gas injection,residual oil saturation decreases and becomes more uniformly distributed,indicating that the combined action of water and gas significantly improves both sweep efficiency and microscopic displacement.展开更多
Automation and intelligence have become the primary trends in the design of investment casting processes.However,the design of gating and riser systems still lacks precise quantitative evaluation criteria.Numerical si...Automation and intelligence have become the primary trends in the design of investment casting processes.However,the design of gating and riser systems still lacks precise quantitative evaluation criteria.Numerical simulation plays a significant role in quantitatively evaluating current processes and making targeted improvements,but its limitations lie in the inability to dynamically reflect the formation outcomes of castings under varying process conditions,making real-time adjustments to gating and riser designs challenging.In this study,an automated design model for gating and riser systems based on integrated parametric 3D modeling-simulation framework is proposed,which enhances the flexibility and usability of evaluating the casting process by simulation.Firstly,geometric feature extraction technology is employed to obtain the geometric information of the target casting.Based on this information,an automated design framework for gating and riser systems is established,incorporating multiple structural parameters for real-time process control.Subsequently,the simulation results for various structural parameters are analyzed,and the influence of these parameters on casting formation is thoroughly investigated.Finally,the optimal design scheme is generated and validated through experimental verification.Simulation analysis and experimental results show that using a larger gate neck(24 mm in side length) and external risers promotes a more uniform temperature distribution and a more stable flow state,effectively eliminating shrinkage cavities and enhancing process yield by 15%.展开更多
The rapid advancement of machine learning based tight-binding Hamiltonian(MLTB)methods has opened new avenues for efficient and accurate electronic structure simulations,particularly in large-scale systems and long-ti...The rapid advancement of machine learning based tight-binding Hamiltonian(MLTB)methods has opened new avenues for efficient and accurate electronic structure simulations,particularly in large-scale systems and long-time scenarios.This review begins with a concise overview of traditional tight-binding(TB)models,including both(semi-)empirical and first-principles approaches,establishing the foundation for understanding MLTB developments.We then present a systematic classification of existing MLTB methodologies,grouped into two major categories:direct prediction of TB Hamiltonian elements and inference of empirical parameters.A comparative analysis with other ML-based electronic structure models is also provided,highlighting the advancement of MLTB approaches.Finally,we explore the emerging MLTB application ecosystem,highlighting how the integration of MLTB models with a diverse suite of post-processing tools from linear-scaling solvers to quantum transport frameworks and molecular dynamics interfaces is essential for tackling complex scientific problems across different domains.The continued advancement of this integrated paradigm promises to accelerate materials discovery and open new frontiers in the predictive simulation of complex quantum phenomena.展开更多
The analysis of the characteristics of the cushion process of the pneumatic cushion cylinder is presented, and the nonlinear model of pneumatic cushion cylinders is built in the form of nonlinear differential equation...The analysis of the characteristics of the cushion process of the pneumatic cushion cylinder is presented, and the nonlinear model of pneumatic cushion cylinders is built in the form of nonlinear differential equations. Besides, through the simulation of the pressure in the cushion chamber, the characteristics of the pneumatic cushion cylinder are obtained, which helps to understand the performance of the pneumatic cushion cylinder and improve or design the better cushion structure.展开更多
This paper presents two approaches for system-level simulation of force-balance accelerometers. The derivation of the system-level model is elaborated and simulation results are obtained from the implementation of tho...This paper presents two approaches for system-level simulation of force-balance accelerometers. The derivation of the system-level model is elaborated and simulation results are obtained from the implementation of those strategies on the fabricated silicon force-balance MEMS accelerometer. The mathematical model presented is implemented in VHDL- AMS and SIMULINK TM,respectively. The simulation results from the two approaches are compared and show a slight difference. Using VHDL-AMS is flexible,reusable,and more accurate. But there is not a mature solver developed for the language and this approach takes more time, while the simulation model can be easily built and quickly evaluated using SIMULINK.展开更多
In order to explore the influence of welding parameters and to investigate the Al alloy (AA) nugget formation process, a comprehensive model involving electrical-thermal-mechanical and metallurgical analysis was estab...In order to explore the influence of welding parameters and to investigate the Al alloy (AA) nugget formation process, a comprehensive model involving electrical-thermal-mechanical and metallurgical analysis was established to numerically display the resistance spot welding (RSW) process within multiple fields and understand the AA-RSW physics. A multi-disciplinary finite element method (FEM) framework and a empirical sub-model were built to analyze the affecting factors on weld nugget and the underlying nature of welding physics with dynamic simulation procedure. Specifically, a counter-intuitive phenomenon of the resistance time-variation caused by the transient inverse virtual variation (TIVV) effect was highlighted and analyzed on the basis of welding current and temperature distribution simulation. The empirical model describing the TIVV phenomenon was used for modifying the dynamic resistance simulation during the AA spot welding process. The numerical and experimental results show that the proposed multi-field FEM model agrees with the measured AA welding feature, and the modified dynamic resistance model captures the physics of nugget growth and the electrical-thermal behavior under varying welding current and fluctuating heat input.展开更多
AIGaN/GaN HEMTs are investigated by numerical simulation from the self-consistent solution of Schr6dinger-Poisson-hydrodynamic （HD） systems. The influences of polarization charge and quantum effects are considered i...AIGaN/GaN HEMTs are investigated by numerical simulation from the self-consistent solution of Schr6dinger-Poisson-hydrodynamic （HD） systems. The influences of polarization charge and quantum effects are considered in this model. Then the two-dimensional conduction band and electron distribution, electron temperature characteristics, Id versus Vd and Id versus Vg, transfer characteristics and transconductance curves are obtained. Corresponding analysis and discussion based on the simulation results are subsequently given.展开更多
The previous study on modeling of the tilt rotor aircraft used to put a premium on the complicated aerodynamic computation, and the research on the motion equations is often constrained to frequently use the oversimpl...The previous study on modeling of the tilt rotor aircraft used to put a premium on the complicated aerodynamic computation, and the research on the motion equations is often constrained to frequently use the oversimplified 6-degree of freedom （DOF） rigid body equations. However, the transfiguration of aircraft during transition stage, is complicated due to the aerodynamic interference and the change of center of gravity （CG）. Moreover, the gyroscopic moment caused by tilting the high-speed revolving rotors seriously interferes with the aircraft attitude. The above-cited 6-DOF single rigid body equations do not take the inertia coupling effects into account during transition. For this sake, the article, reckoning the body, the nacelles and the rotors to be independent entities, establishes a realistic model in the form of multi-body motion equations. First, by applying Newton＇s laws and angular momentum theorem to a mass of elements of the aircraft, the multi-body motion equations in inertial flame as well as in body frame are obtained by integrating over all elements. As the equations are of implicit nonlinear differential type, the consistent initial value problem should be solved. Then, a numerical simulation of the differential equations is conducted by means of the Runge-Kutta-Felhberg integral algorithm. The modeling and the simulation algorithm are verified against the data of XV-15 as an example. The model can be used in the area of flight dynamics, flight control and flight safety of tilt rotor air- craft.展开更多
The constitutive modeling and springback simulation for AA2524 sheet in creep age forming（CAF） process were presented.A series of creep aging tests were performed on AA2524 at the temperature of 180-200 °C and ...The constitutive modeling and springback simulation for AA2524 sheet in creep age forming（CAF） process were presented.A series of creep aging tests were performed on AA2524 at the temperature of 180-200 °C and under the stress of 140-210 MPa for 16 h.Based on these experimental data,material constitutive equations which can well characterize creep aging behaviors of the tested alloy were developed.The effect of interior stress distributed along the sheet thickness on springback was simulated using FE software MSC.MARC by compiling the established constitutive models into the user subroutine.The simulation results showed that the amount of sheet springback was 61.12% when merely considering tensile stress existing along the sheet thickness;while sheet springback was up to 65.93% when taking both tensile and compressive stresses into account.In addition,an AA2524 rectangular sheet was subjected to CAF experiment in resistance furnace.The springback value of the formed rectangular sheet was 68.2%,which was much closer to 65.93%.This confirms that both tensile and compressive stresses across the sheet thickness should be considered in accurately predicting springback of the sheet after forming,which can be more consistent with experimental results.展开更多
A more general narrowband regular-shaped geometry-based statistical model(RS-GBSM) combined with the line of sight(LoS) and single bounce(SB) rays for unmanned aerial vehicle(UAV) multiple-input multiple-output(MIMO) ...A more general narrowband regular-shaped geometry-based statistical model(RS-GBSM) combined with the line of sight(LoS) and single bounce(SB) rays for unmanned aerial vehicle(UAV) multiple-input multiple-output(MIMO) channel is proposed in this paper. The channel characteristics, including space-time correlation function(STCF), Doppler power spectral density(DPSD), level crossing rate(LCR) and average fade duration(AFD), are derived based on the single sphere reference model for a non-isotropic environment. The corresponding sum-of-sinusoids(SoS) simulation models including both the deterministic model and statistical model with finite scatterers are also proposed for practicable implementation. The simulation results illustrate that the simulation models well reproduce the channel characteristics of the single sphere reference model with sufficient simulation scatterers. And the statistical model has a better approximation of the reference model in comparison with the deterministic one when the simulation trials of the stochastic model are sufficient. The effects of the parameters such as flight height, moving direction and Rice factor on the characteristics are also studied.展开更多
Because the normal operation of the engine is located near the equilibrium manifold, the method of equilibrium mani fold nonlinear dynamic modeling is adopted for turbofan engine more than the local train modeling. Th...Because the normal operation of the engine is located near the equilibrium manifold, the method of equilibrium mani fold nonlinear dynamic modeling is adopted for turbofan engine more than the local train modeling. The method studies the sys tem characteristics near the equilibrium manifold. The modeling method can be realized through dynamic and static twostep, and for the specific parameter modeling steps and algorithm are given. The output of the test data is compared with the model output through numerical simulation, to check the model with an additional set of test data. The simulation results show that the model has reached the requirements of engineering accuracy.展开更多
In order to estimate the readiness, sustainability and support capability of the operational unit, an support simulation concept model of the military equipment is given as viewed from the system engineering modeling ...In order to estimate the readiness, sustainability and support capability of the operational unit, an support simulation concept model of the military equipment is given as viewed from the system engineering modeling and simulation. Simulation test of military aircraft is analyzed in detail, it is composed of the operational mission, function maintenance process and resource modeling.展开更多
Various velocity models have been built for Southeast Qinghai-Xizang Plateau with the purpose of revealing the internal dynamics and estimating local seismic hazards.In this study,we use a 3-D full-waveform modeling p...Various velocity models have been built for Southeast Qinghai-Xizang Plateau with the purpose of revealing the internal dynamics and estimating local seismic hazards.In this study,we use a 3-D full-waveform modeling package to systematically validate three published continental-scale velocity models,that is,Shen2016,FWEA18,and USTClitho1.0,leveraging the ample datasets in Southeast Qinghai-Xizang Plateau region.Travel time residuals and waveform similarities are measured between observed empirical Green’s functions and synthetic waveforms.The results show that the Shen2016 model,derived from traditional surface wave tomography,performs best in fitting Rayleigh waves in the Southeast Qinghai-Xizang Plateau,followed by FWEA18,built from full-waveform inversion of long-period body and surface waves.The USTClitho1.0 model,although inverted from body wave datasets,is comparable with FWEA18 in fitting Rayleigh waves.The results also show that all the models are faster than the ground-truth model and show relatively large travel-time residuals and poor waveform similarities at shorter period bands,possibly caused by small-scale structural heterogeneities in the shallower crust.We further invert the time residuals for spatial velocity residuals and reveal that all three models underestimate the amplitudes of high-and low-velocity anomalies.The underestimated amplitude is up to 4%,which is non-negligible considering that the overall amplitude of anomalies is only 5%−10%in the crust.These results suggest that datasets and the inversion method are both essential to building accurate models and further refinements of these models are necessary.展开更多
The global rise in energy demand, particularly in remote and sparsely populated regions, necessitates innovative and cost-effective electrical distribution solutions. Traditional Rural Electrification (RE) methods, li...The global rise in energy demand, particularly in remote and sparsely populated regions, necessitates innovative and cost-effective electrical distribution solutions. Traditional Rural Electrification (RE) methods, like Conventional Rural Electrification (CRE), have proven economically unfeasible in such areas due to high infrastructure costs and low electricity demand. Consequently, Unconventional Rural Electrification (URE) technologies, such as Capacitor Coupled Substations (CCS), are gaining attention as viable alternatives. This study presents the design and simulation of an 80 kW CCS system, which taps power directly from a 132 kV transmission line to supply low-voltage consumers. The critical components of the CCS, the capacitors are calculated, then a MATLAB/Simulink model with the attained results is executed. Mathematical representation and state-space representation for maintaining the desired tapped voltage area also developed. The research further explores the feasibility and operational performance of this CCS configuration, aiming to address the challenges of rural electrification by offering a sustainable and scalable solution. The results show that the desired value of the tapped voltage can be achieved at any level of High Voltage (HV) with the selection of capacitors that are correctly rated. With an adequately designed control strategy, the research also shows that tapped voltage can be attained under both steady-state and dynamic loads. By leveraging CCS technology, the study demonstrates the potential for delivering reliable electricity to underserved areas, highlighting the system’s practicality and effectiveness in overcoming the limitations of conventional distribution methods.展开更多
Dynamic modeling and numerical simulation of hydrate slurry flow behavior are of great importance to offshore hydrate management.For this purpose, a dynamic model of hydrate agglomeration was proposed in this paper.Ba...Dynamic modeling and numerical simulation of hydrate slurry flow behavior are of great importance to offshore hydrate management.For this purpose, a dynamic model of hydrate agglomeration was proposed in this paper.Based on population balance equation, the frame of the dynamic model was established first, which took both hydrate agglomeration and hydrate breakage into consideration.Then, the calculating methods of four key parameters involved in the dynamic model were given according to hydrate agglomeration dynamics.The four key parameters are collision frequency, agglomeration efficiency, breakage frequency and the size distribution of sub particles resulting from particle breakage.After the whole dynamic model was built, it was combined with several traditional solid–liquid flow models and then together solved by the CFD software FLUENT 14.5.Finally, using this method, the influences of flow rate and hydrate volume fraction on hydrate particle size distribution, hydrate volume concentration distribution and pipeline pressure drop were simulated and analyzed.展开更多
A deep understanding of crop-water eco-physiological relations is the basis for quantifying plant physiological responses to soil water stress. Pot experiments were conducted to investigate the winter wheat crop-water...A deep understanding of crop-water eco-physiological relations is the basis for quantifying plant physiological responses to soil water stress. Pot experiments were conducted to investigate the winter wheat crop-water relations under both drought and waterlogging conditions in two sequential growing seasons from 2000 to 2002, and then the data were used to develop and validate models simulating the responses of winter wheat growth to drought and waterlogging stress. The experiment consisted of four treatments, waterlogging (keep 1 to 2 cm water layer depth above soil surface), control (70%-80% field capacity), light drought (40%-50% field capacity) and severe drought (30%-40% field capacity) with six replicates at five stages in the 2000-2001 growth season. Three soil water content treatments (waterlogging, control and drought) with two replicates were designed in the 2001-2002 growth season. Waterlogging and control treatments are the same as in the 2000-2001 growth season. For the drought treatment, no water was supplied and the soil moisture decreased from field capacity to wilting point. Leaf net photosynthetic rate, transpiration rate, predawn leaf water potential, soil water potential, soil water content and dry matter weight of individual organs were measured. Based on crop-water eco-physiological relations, drought and waterlogging stress factors for winter wheat growth simulation model were put forward. Drought stress factors integrated soil water availability, the sensitivity of different development stages and the difference between physiological processes (such as photosynthesis, transpiration and partitioning). The quantification of waterlogging stress factor considered different crop species, soil water status, waterlogging days and sensitivity at different growth stages. Data sets from the pot experiments revealed favorable performance reliability for the simulation sub-models with the drought and waterlogging stress factors.展开更多
The efficiency of particle screening was studied over a range of vibrational parameters including amplitude, frequency and vibrational direction. The Discrete Element Method (DEM) was used to simulate the screening pr...The efficiency of particle screening was studied over a range of vibrational parameters including amplitude, frequency and vibrational direction. The Discrete Element Method (DEM) was used to simulate the screening process. A functional relationship between efficiency and the parameters, both singly and combined, is established. The function is a complicated exponential. Optimal amplitude and frequency values are smaller for particles near the mesh and larger for other particles. The optimum vibration angle is 45° for nearly all kinds of particles. A transverse velocity, V⊥, was defined and V⊥=0.2 m/s was identified to be the most efficient operating point by both simulation and experimental observation. Comparison of these results with those reported by others is included.展开更多
A novel method is proposed to combine the wall-modeled large-eddy simulation(LES) with the diffuse-interface direct-forcing immersed boundary(IB) method.The new developments in this method include:(i) the momentum equ...A novel method is proposed to combine the wall-modeled large-eddy simulation(LES) with the diffuse-interface direct-forcing immersed boundary(IB) method.The new developments in this method include:(i) the momentum equation is integrated along the wall-normal direction to link the tangential component of the effective body force for the IB method to the wall shear stress predicted by the wall model;(ii) a set of Lagrangian points near the wall are introduced to compute the normal component of the effective body force for the IB method by reconstructing the normal component of the velocity. This novel method will be a classical direct-forcing IB method if the grid is fine enough to resolve the flow near the wall. The method is used to simulate the flows around the DARPA SUBOFF model. The results obtained are well comparable to the measured experimental data and wall-resolved LES results.展开更多
Pore structure of porous media, including pore size and topology, is rather complex. In immiscible twophase displacement process, the capillary force affected by pore size dominates the two-phase flow in the porous me...Pore structure of porous media, including pore size and topology, is rather complex. In immiscible twophase displacement process, the capillary force affected by pore size dominates the two-phase flow in the porous media, affecting displacement results. Direct observation of the flow patterns in the porous media is difficult, and therefore knowledge about the two-phase displacement flow is insufficient. In this paper, a two-dimensional(2D) pore structure was extracted from a sandstone sample, and the flow process that CO_2 displaces resident brine in the extracted pore structure was simulated using the Navier eStokes equation combined with the conservative level set method. The simulation results reveal that the pore throat is a crucial factor for determining CO_2 displacement process in the porous media. The two-phase meniscuses in each pore throat were in a self-adjusting process. In the displacement process,CO_2 preferentially broke through the maximum pore throat. Before breaking through the maximum pore throat, the pressure of CO_2 continually increased, and the curvature and position of two-phase interfaces in the other pore throats adjusted accordingly. Once the maximum pore throat was broken through by the CO_2, the capillary force in the other pore throats released accordingly; subsequently, the interfaces withdrew under the effect of capillary fore, preparing for breaking through the next pore throat.Therefore, the two-phase displacement in CO_2 injection is accompanied by the breaking through and adjusting of the two-phase interfaces.展开更多
基金funded by the Research Project of CNOOC(China)Co.,Ltd.Shanghai Branch,grant number 202417716474Research Project of CNOOC Limited,grant number KJZX-2024-0102.
文摘Weak water-drive offshore reservoirs with complex pore architecture and strong permeability heterogeneity present major challenges,including rapid depletion of formation energy,low waterflood efficiency,and significant lateral and vertical variability in crude oil properties,all of which contribute to limited recovery.To support more effective field development,alternative strategies and a deeper understanding of pore-scale flow behavior are urgently needed.In this work,CT imaging and digital image processing were used to construct a digital rock model representative of the target reservoir.A pore-scale flow model was then developed,and the Volume of Fluid(VOF)method was applied to simulate and optimize waterflooding schemes aimed at boosting oil recovery.Optimization focused on adjusting injection rates,varying the oil–water viscosity ratio,and implementing a water-alternating-gas(WAG)process.Results show that,for equal injection volumes,higher injection rates cause early water breakthrough through high-permeability pathways,yielding slower gains in recovery.Lowering the oil–water viscosity ratio improves mobility control,suppresses viscous fingering,enlarges sweep volume,and enhances recovery.When CH_(4)becomes fully miscible,it dissolves into the crude oil,lowering viscosity and eliminating interfacial tension,thereby providing greater displacement efficiency than partially miscible injection.Following a switch from water to gas injection,residual oil saturation decreases and becomes more uniformly distributed,indicating that the combined action of water and gas significantly improves both sweep efficiency and microscopic displacement.
基金financially supported by the National Key Research and Development Program of China (2022YFB3706802)。
文摘Automation and intelligence have become the primary trends in the design of investment casting processes.However,the design of gating and riser systems still lacks precise quantitative evaluation criteria.Numerical simulation plays a significant role in quantitatively evaluating current processes and making targeted improvements,but its limitations lie in the inability to dynamically reflect the formation outcomes of castings under varying process conditions,making real-time adjustments to gating and riser designs challenging.In this study,an automated design model for gating and riser systems based on integrated parametric 3D modeling-simulation framework is proposed,which enhances the flexibility and usability of evaluating the casting process by simulation.Firstly,geometric feature extraction technology is employed to obtain the geometric information of the target casting.Based on this information,an automated design framework for gating and riser systems is established,incorporating multiple structural parameters for real-time process control.Subsequently,the simulation results for various structural parameters are analyzed,and the influence of these parameters on casting formation is thoroughly investigated.Finally,the optimal design scheme is generated and validated through experimental verification.Simulation analysis and experimental results show that using a larger gate neck(24 mm in side length) and external risers promotes a more uniform temperature distribution and a more stable flow state,effectively eliminating shrinkage cavities and enhancing process yield by 15%.
基金supported by the Advanced Materials-National Science and Technology Major Project(Grant No.2025ZD0618401)the National Natural Science Foundation of China(Grant No.12504285)+1 种基金the Natural Science Foundation of Jiangsu Province(Grant No.BK20250472)NFSG grant from BITS-Pilani,Dubai campus。
文摘The rapid advancement of machine learning based tight-binding Hamiltonian(MLTB)methods has opened new avenues for efficient and accurate electronic structure simulations,particularly in large-scale systems and long-time scenarios.This review begins with a concise overview of traditional tight-binding(TB)models,including both(semi-)empirical and first-principles approaches,establishing the foundation for understanding MLTB developments.We then present a systematic classification of existing MLTB methodologies,grouped into two major categories:direct prediction of TB Hamiltonian elements and inference of empirical parameters.A comparative analysis with other ML-based electronic structure models is also provided,highlighting the advancement of MLTB approaches.Finally,we explore the emerging MLTB application ecosystem,highlighting how the integration of MLTB models with a diverse suite of post-processing tools from linear-scaling solvers to quantum transport frameworks and molecular dynamics interfaces is essential for tackling complex scientific problems across different domains.The continued advancement of this integrated paradigm promises to accelerate materials discovery and open new frontiers in the predictive simulation of complex quantum phenomena.
文摘The analysis of the characteristics of the cushion process of the pneumatic cushion cylinder is presented, and the nonlinear model of pneumatic cushion cylinders is built in the form of nonlinear differential equations. Besides, through the simulation of the pressure in the cushion chamber, the characteristics of the pneumatic cushion cylinder are obtained, which helps to understand the performance of the pneumatic cushion cylinder and improve or design the better cushion structure.
文摘This paper presents two approaches for system-level simulation of force-balance accelerometers. The derivation of the system-level model is elaborated and simulation results are obtained from the implementation of those strategies on the fabricated silicon force-balance MEMS accelerometer. The mathematical model presented is implemented in VHDL- AMS and SIMULINK TM,respectively. The simulation results from the two approaches are compared and show a slight difference. Using VHDL-AMS is flexible,reusable,and more accurate. But there is not a mature solver developed for the language and this approach takes more time, while the simulation model can be easily built and quickly evaluated using SIMULINK.
基金Projects (11202125, 61175038) supported by the National Natural Science Foundation of China
文摘In order to explore the influence of welding parameters and to investigate the Al alloy (AA) nugget formation process, a comprehensive model involving electrical-thermal-mechanical and metallurgical analysis was established to numerically display the resistance spot welding (RSW) process within multiple fields and understand the AA-RSW physics. A multi-disciplinary finite element method (FEM) framework and a empirical sub-model were built to analyze the affecting factors on weld nugget and the underlying nature of welding physics with dynamic simulation procedure. Specifically, a counter-intuitive phenomenon of the resistance time-variation caused by the transient inverse virtual variation (TIVV) effect was highlighted and analyzed on the basis of welding current and temperature distribution simulation. The empirical model describing the TIVV phenomenon was used for modifying the dynamic resistance simulation during the AA spot welding process. The numerical and experimental results show that the proposed multi-field FEM model agrees with the measured AA welding feature, and the modified dynamic resistance model captures the physics of nugget growth and the electrical-thermal behavior under varying welding current and fluctuating heat input.
文摘AIGaN/GaN HEMTs are investigated by numerical simulation from the self-consistent solution of Schr6dinger-Poisson-hydrodynamic （HD） systems. The influences of polarization charge and quantum effects are considered in this model. Then the two-dimensional conduction band and electron distribution, electron temperature characteristics, Id versus Vd and Id versus Vg, transfer characteristics and transconductance curves are obtained. Corresponding analysis and discussion based on the simulation results are subsequently given.
基金Graduate Innovation and Practice Foundation of Beijing University of Aeronautics amd Astronautics
文摘The previous study on modeling of the tilt rotor aircraft used to put a premium on the complicated aerodynamic computation, and the research on the motion equations is often constrained to frequently use the oversimplified 6-degree of freedom （DOF） rigid body equations. However, the transfiguration of aircraft during transition stage, is complicated due to the aerodynamic interference and the change of center of gravity （CG）. Moreover, the gyroscopic moment caused by tilting the high-speed revolving rotors seriously interferes with the aircraft attitude. The above-cited 6-DOF single rigid body equations do not take the inertia coupling effects into account during transition. For this sake, the article, reckoning the body, the nacelles and the rotors to be independent entities, establishes a realistic model in the form of multi-body motion equations. First, by applying Newton＇s laws and angular momentum theorem to a mass of elements of the aircraft, the multi-body motion equations in inertial flame as well as in body frame are obtained by integrating over all elements. As the equations are of implicit nonlinear differential type, the consistent initial value problem should be solved. Then, a numerical simulation of the differential equations is conducted by means of the Runge-Kutta-Felhberg integral algorithm. The modeling and the simulation algorithm are verified against the data of XV-15 as an example. The model can be used in the area of flight dynamics, flight control and flight safety of tilt rotor air- craft.
基金Project(2014CB046602)supported by the National Basic Research Program of ChinaProject(20120162110003)supported by Ph D Programs Foundation of Ministry of Education of China
文摘The constitutive modeling and springback simulation for AA2524 sheet in creep age forming（CAF） process were presented.A series of creep aging tests were performed on AA2524 at the temperature of 180-200 °C and under the stress of 140-210 MPa for 16 h.Based on these experimental data,material constitutive equations which can well characterize creep aging behaviors of the tested alloy were developed.The effect of interior stress distributed along the sheet thickness on springback was simulated using FE software MSC.MARC by compiling the established constitutive models into the user subroutine.The simulation results showed that the amount of sheet springback was 61.12% when merely considering tensile stress existing along the sheet thickness;while sheet springback was up to 65.93% when taking both tensile and compressive stresses into account.In addition,an AA2524 rectangular sheet was subjected to CAF experiment in resistance furnace.The springback value of the formed rectangular sheet was 68.2%,which was much closer to 65.93%.This confirms that both tensile and compressive stresses across the sheet thickness should be considered in accurately predicting springback of the sheet after forming,which can be more consistent with experimental results.
基金supported in part by the National Natural Science Foundation of China under Grant 61622101 and Grant 61571020National Science and Technology Major Project under Grant 2018ZX03001031
文摘A more general narrowband regular-shaped geometry-based statistical model(RS-GBSM) combined with the line of sight(LoS) and single bounce(SB) rays for unmanned aerial vehicle(UAV) multiple-input multiple-output(MIMO) channel is proposed in this paper. The channel characteristics, including space-time correlation function(STCF), Doppler power spectral density(DPSD), level crossing rate(LCR) and average fade duration(AFD), are derived based on the single sphere reference model for a non-isotropic environment. The corresponding sum-of-sinusoids(SoS) simulation models including both the deterministic model and statistical model with finite scatterers are also proposed for practicable implementation. The simulation results illustrate that the simulation models well reproduce the channel characteristics of the single sphere reference model with sufficient simulation scatterers. And the statistical model has a better approximation of the reference model in comparison with the deterministic one when the simulation trials of the stochastic model are sufficient. The effects of the parameters such as flight height, moving direction and Rice factor on the characteristics are also studied.
文摘Because the normal operation of the engine is located near the equilibrium manifold, the method of equilibrium mani fold nonlinear dynamic modeling is adopted for turbofan engine more than the local train modeling. The method studies the sys tem characteristics near the equilibrium manifold. The modeling method can be realized through dynamic and static twostep, and for the specific parameter modeling steps and algorithm are given. The output of the test data is compared with the model output through numerical simulation, to check the model with an additional set of test data. The simulation results show that the model has reached the requirements of engineering accuracy.
文摘In order to estimate the readiness, sustainability and support capability of the operational unit, an support simulation concept model of the military equipment is given as viewed from the system engineering modeling and simulation. Simulation test of military aircraft is analyzed in detail, it is composed of the operational mission, function maintenance process and resource modeling.
基金supported by the Special Fund of the Institute of Geophysics,China Earthquake Administration(Nos.DQJB23R28 and DQJB22K40)the National Natural Science Foundation of China(Nos.42304078,U1839210 and 42104043).
文摘Various velocity models have been built for Southeast Qinghai-Xizang Plateau with the purpose of revealing the internal dynamics and estimating local seismic hazards.In this study,we use a 3-D full-waveform modeling package to systematically validate three published continental-scale velocity models,that is,Shen2016,FWEA18,and USTClitho1.0,leveraging the ample datasets in Southeast Qinghai-Xizang Plateau region.Travel time residuals and waveform similarities are measured between observed empirical Green’s functions and synthetic waveforms.The results show that the Shen2016 model,derived from traditional surface wave tomography,performs best in fitting Rayleigh waves in the Southeast Qinghai-Xizang Plateau,followed by FWEA18,built from full-waveform inversion of long-period body and surface waves.The USTClitho1.0 model,although inverted from body wave datasets,is comparable with FWEA18 in fitting Rayleigh waves.The results also show that all the models are faster than the ground-truth model and show relatively large travel-time residuals and poor waveform similarities at shorter period bands,possibly caused by small-scale structural heterogeneities in the shallower crust.We further invert the time residuals for spatial velocity residuals and reveal that all three models underestimate the amplitudes of high-and low-velocity anomalies.The underestimated amplitude is up to 4%,which is non-negligible considering that the overall amplitude of anomalies is only 5%−10%in the crust.These results suggest that datasets and the inversion method are both essential to building accurate models and further refinements of these models are necessary.
文摘The global rise in energy demand, particularly in remote and sparsely populated regions, necessitates innovative and cost-effective electrical distribution solutions. Traditional Rural Electrification (RE) methods, like Conventional Rural Electrification (CRE), have proven economically unfeasible in such areas due to high infrastructure costs and low electricity demand. Consequently, Unconventional Rural Electrification (URE) technologies, such as Capacitor Coupled Substations (CCS), are gaining attention as viable alternatives. This study presents the design and simulation of an 80 kW CCS system, which taps power directly from a 132 kV transmission line to supply low-voltage consumers. The critical components of the CCS, the capacitors are calculated, then a MATLAB/Simulink model with the attained results is executed. Mathematical representation and state-space representation for maintaining the desired tapped voltage area also developed. The research further explores the feasibility and operational performance of this CCS configuration, aiming to address the challenges of rural electrification by offering a sustainable and scalable solution. The results show that the desired value of the tapped voltage can be achieved at any level of High Voltage (HV) with the selection of capacitors that are correctly rated. With an adequately designed control strategy, the research also shows that tapped voltage can be attained under both steady-state and dynamic loads. By leveraging CCS technology, the study demonstrates the potential for delivering reliable electricity to underserved areas, highlighting the system’s practicality and effectiveness in overcoming the limitations of conventional distribution methods.
基金Supported by Shandong Provincial Natural Science Foundation,China(ZR2017MEE057)the Fundamental Research Funds for the Central Universities(14CX02207A,17CX05006,17CX06017)the Graduate Innovation Project of China University of Petroleum(East China)(YCX2017062)
文摘Dynamic modeling and numerical simulation of hydrate slurry flow behavior are of great importance to offshore hydrate management.For this purpose, a dynamic model of hydrate agglomeration was proposed in this paper.Based on population balance equation, the frame of the dynamic model was established first, which took both hydrate agglomeration and hydrate breakage into consideration.Then, the calculating methods of four key parameters involved in the dynamic model were given according to hydrate agglomeration dynamics.The four key parameters are collision frequency, agglomeration efficiency, breakage frequency and the size distribution of sub particles resulting from particle breakage.After the whole dynamic model was built, it was combined with several traditional solid–liquid flow models and then together solved by the CFD software FLUENT 14.5.Finally, using this method, the influences of flow rate and hydrate volume fraction on hydrate particle size distribution, hydrate volume concentration distribution and pipeline pressure drop were simulated and analyzed.
基金Project supported by the National High Technology Research and Development Program of China (863 Program) (No. 2003AA209030) High Technology Research and Development Program of Jiangsu Province (No. BG2004320) the National Natural Science Foundation
文摘A deep understanding of crop-water eco-physiological relations is the basis for quantifying plant physiological responses to soil water stress. Pot experiments were conducted to investigate the winter wheat crop-water relations under both drought and waterlogging conditions in two sequential growing seasons from 2000 to 2002, and then the data were used to develop and validate models simulating the responses of winter wheat growth to drought and waterlogging stress. The experiment consisted of four treatments, waterlogging (keep 1 to 2 cm water layer depth above soil surface), control (70%-80% field capacity), light drought (40%-50% field capacity) and severe drought (30%-40% field capacity) with six replicates at five stages in the 2000-2001 growth season. Three soil water content treatments (waterlogging, control and drought) with two replicates were designed in the 2001-2002 growth season. Waterlogging and control treatments are the same as in the 2000-2001 growth season. For the drought treatment, no water was supplied and the soil moisture decreased from field capacity to wilting point. Leaf net photosynthetic rate, transpiration rate, predawn leaf water potential, soil water potential, soil water content and dry matter weight of individual organs were measured. Based on crop-water eco-physiological relations, drought and waterlogging stress factors for winter wheat growth simulation model were put forward. Drought stress factors integrated soil water availability, the sensitivity of different development stages and the difference between physiological processes (such as photosynthesis, transpiration and partitioning). The quantification of waterlogging stress factor considered different crop species, soil water status, waterlogging days and sensitivity at different growth stages. Data sets from the pot experiments revealed favorable performance reliability for the simulation sub-models with the drought and waterlogging stress factors.
基金the Special Topic of Key Science and Technology of Fujian Province Fund (No.2006HZ0002-2)
文摘The efficiency of particle screening was studied over a range of vibrational parameters including amplitude, frequency and vibrational direction. The Discrete Element Method (DEM) was used to simulate the screening process. A functional relationship between efficiency and the parameters, both singly and combined, is established. The function is a complicated exponential. Optimal amplitude and frequency values are smaller for particles near the mesh and larger for other particles. The optimum vibration angle is 45° for nearly all kinds of particles. A transverse velocity, V⊥, was defined and V⊥=0.2 m/s was identified to be the most efficient operating point by both simulation and experimental observation. Comparison of these results with those reported by others is included.
基金Project supported by the National Natural Science Foundation of China(Nos.91752118,11672305,11232011,and 11572331)the Strategic Priority Research Program(No.XDB22040104)the Key Research Program of Frontier Sciences of the Chinese Academy of Sciences(No.QYZDJ-SSWSYS002)
文摘A novel method is proposed to combine the wall-modeled large-eddy simulation(LES) with the diffuse-interface direct-forcing immersed boundary(IB) method.The new developments in this method include:(i) the momentum equation is integrated along the wall-normal direction to link the tangential component of the effective body force for the IB method to the wall shear stress predicted by the wall model;(ii) a set of Lagrangian points near the wall are introduced to compute the normal component of the effective body force for the IB method by reconstructing the normal component of the velocity. This novel method will be a classical direct-forcing IB method if the grid is fine enough to resolve the flow near the wall. The method is used to simulate the flows around the DARPA SUBOFF model. The results obtained are well comparable to the measured experimental data and wall-resolved LES results.
基金funded by Key Laboratory of Coal-based CO_2 Capture and Geological Storage,Jiangsu Province,ChinaUS Advanced Coal Technology Consortium(No.2013 DFB60140-08)
文摘Pore structure of porous media, including pore size and topology, is rather complex. In immiscible twophase displacement process, the capillary force affected by pore size dominates the two-phase flow in the porous media, affecting displacement results. Direct observation of the flow patterns in the porous media is difficult, and therefore knowledge about the two-phase displacement flow is insufficient. In this paper, a two-dimensional(2D) pore structure was extracted from a sandstone sample, and the flow process that CO_2 displaces resident brine in the extracted pore structure was simulated using the Navier eStokes equation combined with the conservative level set method. The simulation results reveal that the pore throat is a crucial factor for determining CO_2 displacement process in the porous media. The two-phase meniscuses in each pore throat were in a self-adjusting process. In the displacement process,CO_2 preferentially broke through the maximum pore throat. Before breaking through the maximum pore throat, the pressure of CO_2 continually increased, and the curvature and position of two-phase interfaces in the other pore throats adjusted accordingly. Once the maximum pore throat was broken through by the CO_2, the capillary force in the other pore throats released accordingly; subsequently, the interfaces withdrew under the effect of capillary fore, preparing for breaking through the next pore throat.Therefore, the two-phase displacement in CO_2 injection is accompanied by the breaking through and adjusting of the two-phase interfaces.
