To reduce the damage of the pressurizing panel structure of a fuselage caused by an explosion at the“least risk bomb location”in an aircraft structure,a new pre-separation panel structure was designed to resist blas...To reduce the damage of the pressurizing panel structure of a fuselage caused by an explosion at the“least risk bomb location”in an aircraft structure,a new pre-separation panel structure was designed to resist blast loading.First,the dynamic strain response and morphology of impact damage of the new pre-separation panel were measured in an impact damage test.Second,the commercial software LS-DYNA was used to calculate the propagation of the blast shock wave,and the results were compared with empirical equations to verify the rationality of the numerical calculation method.Finally,the fluid–structure coupling method was used to calculate the damage process of the pre-separation panel structure under the impact of an explosion wave and an impact block.The calculated results were in good agreement with the test results,which showed the rationality of the calculation method and the model.The residual strength of the damaged pre-separation panel was significantly higher than that of the original damaged panel.The results show that the new pre-separation panel structure is reasonable and has certain significance for guiding the design of plenum chambers with strong resistance to implosion for aircraft fuselages.展开更多
The plenum chamber of a heat setting machine is a key structure for distributing hot air to different air channels.Its outlet velocity uniformity directly determines the heating uniformity of textiles,significantly af...The plenum chamber of a heat setting machine is a key structure for distributing hot air to different air channels.Its outlet velocity uniformity directly determines the heating uniformity of textiles,significantly affecting the heat setting performance.In a traditional heat setting machine,the outlet airflow maldistribution of the plenum chamber still exists.In this study,a novel plenum chamber with an airfoil baffle was established to improve the uniformity of the velocity distribution at the outlet in a heat setting machine.The structural influence of the plenum chamber on the velocity distribution was investigated using a computational fluid dynamics program.It was found that a chamber with a smaller outlet partition thickness had a better outlet velocity uniformity.The structural optimization of the plenum chamber was conducted using the particle swarm optimization algorithm.The outlet partition thickness,the transverse distance and the longitudinal distance of the optimized plenum chamber were 20,686.2 and 274.6 mm,respectively.Experiments were carried out.The experimental and simulated results showed that the optimized plenum chamber with an airfoil baffle could improve the outlet velocity uniformity.The air outlet velocity uniformity index of the optimized plenum chamber with an airfoil baffle was 4.75%higher than that of the plenum chamber without an airfoil baffle and 5.98%higher than that of the conventional chamber with a square baffle in a commercial heat setting machine.展开更多
The 6th Plenary Session of the 18th CPC Central Committee was a very important meeting upon China’s entry into a decisive stage for completing the all-round construction of a moderately prosperous society,opening a n...The 6th Plenary Session of the 18th CPC Central Committee was a very important meeting upon China’s entry into a decisive stage for completing the all-round construction of a moderately prosperous society,opening a new process of展开更多
In order to evaluate the effects of the FHs （flow holes） on the inner barrel, which were installed in the upper plenum of the Monju reactor vessel, a high resolution meshes around the FHs was constructed. Using this...In order to evaluate the effects of the FHs （flow holes） on the inner barrel, which were installed in the upper plenum of the Monju reactor vessel, a high resolution meshes around the FHs was constructed. Using this model, it was mainly clear that in the 40% rated operational conditions, the shape of the FHs on the inner barrel did not change largely to the upper plenum thermal-hydraulics. The effect of the FHs on the honeycomb structure in the upper structure was also investigated in these calculations. The results indicated that the height of thermal stratification interface became lower than that evaluated from the test data.展开更多
THE new leadership in place in the Party since November last year and in their government positions as of March this year have spoken a great deal about the issue of urbanization. This plenum has given two ideas about...THE new leadership in place in the Party since November last year and in their government positions as of March this year have spoken a great deal about the issue of urbanization. This plenum has given two ideas about how accelerated urbanization might occur. One is to address the household registration system,展开更多
The China Society for Human Rights Studies （CSHRS） organized on Nov. 28 a forum to study and implement the guidelines of the third plenary session of the 18th Central Committee of the Communist Party of China （CPC...The China Society for Human Rights Studies （CSHRS） organized on Nov. 28 a forum to study and implement the guidelines of the third plenary session of the 18th Central Committee of the Communist Party of China （CPC）. Executive members of CSHRS and other CSHRS members in Beijing discussed improvement of judicial protection for human rights and legal construction in China. CSHRS President Luo Haocai, who was vice chairman of the 10th National Committee of the Chinese People＇s Political Consultative Conference, delivered a speech at the forum.展开更多
The 20th Central Committee of the Communist Party of China(CPC)convened its fourth plenary session in Beijing from October 20 to 23.Participants at the session deliberated over and adopted the Recommendations of the C...The 20th Central Committee of the Communist Party of China(CPC)convened its fourth plenary session in Beijing from October 20 to 23.Participants at the session deliberated over and adopted the Recommendations of the CPC Central Committee for Formulating the 15th Five-Year Plan for Economic and Social Development,according to a communique of the session released on October 23.The Political Bureau of the CPC Central Committee presided over the meeting.展开更多
Hydraulic performance of an inlet plenum in a printed-circuit heat exchanger has been analyzed using three-dimensional Reynolds-Averaged Navier-Stokes equations. The numerical model of the inlet plenum was constructed...Hydraulic performance of an inlet plenum in a printed-circuit heat exchanger has been analyzed using three-dimensional Reynolds-Averaged Navier-Stokes equations. The numerical model of the inlet plenum was constructed through grid dependency test, calculation domain tests, and turbulence model and numerical scheme selections. Shear stress transport turbulence model was used for analysis of turbulence. Non-uniformity of the flow in zigzag flow channels was evaluated for the reference case. Parametric studies have been performed with the angle of the inlet plenum wall, radius of curvature of the inlet plenum wall, and width of the inlet pipes. The effects of these parameters on the flow uniformity and friction performance were evaluated.展开更多
A comparative computational fluid dynamics(CFD)study was conducted on the three different types of pressurized water reactor(PWR)upper plenum,named TYPE 1(support columns(SCs)and control rod guide tubes(CRGTs)with two...A comparative computational fluid dynamics(CFD)study was conducted on the three different types of pressurized water reactor(PWR)upper plenum,named TYPE 1(support columns(SCs)and control rod guide tubes(CRGTs)with two large windows),TYPE 2(SCs and CRGTs without windows),and TYPE 3(two parallel perforated barrel shells and CRGTs).First,three types of upper plenum geometry information were collected,simplified,and adopted into the BORA facility,which is a 1/5 scale system of the four-loop PWR reactor.Then,the geometry,including the upper half core,upper plenum region,and hot legs,was built using the Salome platform.After that,an unsteady calculation to simulate the reactor balance operation at hot full power scenario was performed.Finally,the differences of flowrate distribution at the core outlet and temperature distribution and transverse velocity inside the hot legs with different upper plenum internals were compared.The results suggest that TYPE 1 upper plenum internals cause the largest flowrate difference at the core outlet while TYPE 3 leads to the most even distributed flowrate.The distribution and evolution pattern of the tangential velocity inside hot legs is highly dependent on the upper plenum internals.Two counter-rotating swirls exist inside the TYPE 1 hot leg and only one swirl revolving around the hog leg axis exist inside the TYPE 2 hot leg.For TYPE 3,two swirls like that of TYPE 1 rotating around the hot leg axis significantly increase the temperature homogenization speed.This research provides meaningful guidelines for the future optimization and design of advanced PWR upper plenum internal structures.展开更多
Most hydrodynamic fluidized bed models, including CFD codes, neglect any effects of the plenum chamber volume. Experiments were performed in a 0.13 m ID fluidization column to determine plenum chamber volume effects o...Most hydrodynamic fluidized bed models, including CFD codes, neglect any effects of the plenum chamber volume. Experiments were performed in a 0.13 m ID fluidization column to determine plenum chamber volume effects on fluidized bed hydrodynamics for FCC and glass particles. Two low-pressure-drop distributors were used, one with a single orifice, and the other with 33 orifices and the same total open area as the single orifice. The results show two peaks in the frequency spectra for the single-orifice distributor, one representing bubble eruption at the bed surface and the other of higher frequency corresponding to the bubbling frequency at the distributor. The latter decreased slightly with increasing plenum volume and with increasing bed depth. For the multi-orifice distributor, broad frequency spectra from pressure measurements became narrower and moved towards higher frequency with decreasing plenum volume.展开更多
文摘To reduce the damage of the pressurizing panel structure of a fuselage caused by an explosion at the“least risk bomb location”in an aircraft structure,a new pre-separation panel structure was designed to resist blast loading.First,the dynamic strain response and morphology of impact damage of the new pre-separation panel were measured in an impact damage test.Second,the commercial software LS-DYNA was used to calculate the propagation of the blast shock wave,and the results were compared with empirical equations to verify the rationality of the numerical calculation method.Finally,the fluid–structure coupling method was used to calculate the damage process of the pre-separation panel structure under the impact of an explosion wave and an impact block.The calculated results were in good agreement with the test results,which showed the rationality of the calculation method and the model.The residual strength of the damaged pre-separation panel was significantly higher than that of the original damaged panel.The results show that the new pre-separation panel structure is reasonable and has certain significance for guiding the design of plenum chambers with strong resistance to implosion for aircraft fuselages.
基金National Natural Science Foundation of China(No.62173307)the Key R&D Projects of Science and Technology Department of Zhejiang Province,China(Nos.2023C01158,2022C01065 and 2022C01188)the Fundamental Research Funds of Zhejiang Sci-Tech University,China(No.22242298-Y)。
文摘The plenum chamber of a heat setting machine is a key structure for distributing hot air to different air channels.Its outlet velocity uniformity directly determines the heating uniformity of textiles,significantly affecting the heat setting performance.In a traditional heat setting machine,the outlet airflow maldistribution of the plenum chamber still exists.In this study,a novel plenum chamber with an airfoil baffle was established to improve the uniformity of the velocity distribution at the outlet in a heat setting machine.The structural influence of the plenum chamber on the velocity distribution was investigated using a computational fluid dynamics program.It was found that a chamber with a smaller outlet partition thickness had a better outlet velocity uniformity.The structural optimization of the plenum chamber was conducted using the particle swarm optimization algorithm.The outlet partition thickness,the transverse distance and the longitudinal distance of the optimized plenum chamber were 20,686.2 and 274.6 mm,respectively.Experiments were carried out.The experimental and simulated results showed that the optimized plenum chamber with an airfoil baffle could improve the outlet velocity uniformity.The air outlet velocity uniformity index of the optimized plenum chamber with an airfoil baffle was 4.75%higher than that of the plenum chamber without an airfoil baffle and 5.98%higher than that of the conventional chamber with a square baffle in a commercial heat setting machine.
文摘The 6th Plenary Session of the 18th CPC Central Committee was a very important meeting upon China’s entry into a decisive stage for completing the all-round construction of a moderately prosperous society,opening a new process of
文摘In order to evaluate the effects of the FHs （flow holes） on the inner barrel, which were installed in the upper plenum of the Monju reactor vessel, a high resolution meshes around the FHs was constructed. Using this model, it was mainly clear that in the 40% rated operational conditions, the shape of the FHs on the inner barrel did not change largely to the upper plenum thermal-hydraulics. The effect of the FHs on the honeycomb structure in the upper structure was also investigated in these calculations. The results indicated that the height of thermal stratification interface became lower than that evaluated from the test data.
文摘THE new leadership in place in the Party since November last year and in their government positions as of March this year have spoken a great deal about the issue of urbanization. This plenum has given two ideas about how accelerated urbanization might occur. One is to address the household registration system,
文摘The China Society for Human Rights Studies （CSHRS） organized on Nov. 28 a forum to study and implement the guidelines of the third plenary session of the 18th Central Committee of the Communist Party of China （CPC）. Executive members of CSHRS and other CSHRS members in Beijing discussed improvement of judicial protection for human rights and legal construction in China. CSHRS President Luo Haocai, who was vice chairman of the 10th National Committee of the Chinese People＇s Political Consultative Conference, delivered a speech at the forum.
文摘The 20th Central Committee of the Communist Party of China(CPC)convened its fourth plenary session in Beijing from October 20 to 23.Participants at the session deliberated over and adopted the Recommendations of the CPC Central Committee for Formulating the 15th Five-Year Plan for Economic and Social Development,according to a communique of the session released on October 23.The Political Bureau of the CPC Central Committee presided over the meeting.
基金supported by the National Research Foundation of Korea (NRF), (Grant No. 2009-0083510)funded by the Korean government (MSIP) through the Multi-phenomena CFD Engineering Research Center
文摘Hydraulic performance of an inlet plenum in a printed-circuit heat exchanger has been analyzed using three-dimensional Reynolds-Averaged Navier-Stokes equations. The numerical model of the inlet plenum was constructed through grid dependency test, calculation domain tests, and turbulence model and numerical scheme selections. Shear stress transport turbulence model was used for analysis of turbulence. Non-uniformity of the flow in zigzag flow channels was evaluated for the reference case. Parametric studies have been performed with the angle of the inlet plenum wall, radius of curvature of the inlet plenum wall, and width of the inlet pipes. The effects of these parameters on the flow uniformity and friction performance were evaluated.
基金the National Natural Science Foundation of China(Grant No.12075185).
文摘A comparative computational fluid dynamics(CFD)study was conducted on the three different types of pressurized water reactor(PWR)upper plenum,named TYPE 1(support columns(SCs)and control rod guide tubes(CRGTs)with two large windows),TYPE 2(SCs and CRGTs without windows),and TYPE 3(two parallel perforated barrel shells and CRGTs).First,three types of upper plenum geometry information were collected,simplified,and adopted into the BORA facility,which is a 1/5 scale system of the four-loop PWR reactor.Then,the geometry,including the upper half core,upper plenum region,and hot legs,was built using the Salome platform.After that,an unsteady calculation to simulate the reactor balance operation at hot full power scenario was performed.Finally,the differences of flowrate distribution at the core outlet and temperature distribution and transverse velocity inside the hot legs with different upper plenum internals were compared.The results suggest that TYPE 1 upper plenum internals cause the largest flowrate difference at the core outlet while TYPE 3 leads to the most even distributed flowrate.The distribution and evolution pattern of the tangential velocity inside hot legs is highly dependent on the upper plenum internals.Two counter-rotating swirls exist inside the TYPE 1 hot leg and only one swirl revolving around the hog leg axis exist inside the TYPE 2 hot leg.For TYPE 3,two swirls like that of TYPE 1 rotating around the hot leg axis significantly increase the temperature homogenization speed.This research provides meaningful guidelines for the future optimization and design of advanced PWR upper plenum internal structures.
基金the Natural Sciences and Engineering Research Council of Canada for supporting this project financially
文摘Most hydrodynamic fluidized bed models, including CFD codes, neglect any effects of the plenum chamber volume. Experiments were performed in a 0.13 m ID fluidization column to determine plenum chamber volume effects on fluidized bed hydrodynamics for FCC and glass particles. Two low-pressure-drop distributors were used, one with a single orifice, and the other with 33 orifices and the same total open area as the single orifice. The results show two peaks in the frequency spectra for the single-orifice distributor, one representing bubble eruption at the bed surface and the other of higher frequency corresponding to the bubbling frequency at the distributor. The latter decreased slightly with increasing plenum volume and with increasing bed depth. For the multi-orifice distributor, broad frequency spectra from pressure measurements became narrower and moved towards higher frequency with decreasing plenum volume.
