Ceramic thin plates were prepared using kaolin,potassium sodium feldspar and quartz powder as the main raw materials and kaolin,α-Al_(2)O_(3),MoO_(3) and AlF_(3)·3H_(2)O as additives.The experiment examined the ...Ceramic thin plates were prepared using kaolin,potassium sodium feldspar and quartz powder as the main raw materials and kaolin,α-Al_(2)O_(3),MoO_(3) and AlF_(3)·3H_(2)O as additives.The experiment examined the effects of different additives on mullite formation,as well as the microstructure and properties of the ceramic thin plates.Additionally,the study explored the toughening and strengthening mechanisms induced by the additives,providing a theoretical foundation for further optimizing the toughness of ceramic thin plates.The results showed that the D4 sample fired at 1220℃(with an addition of 20 wt% α-Al_(2)O_(3))exhibited the best performance,with a water absorption rate of 0.07%,apparent porosity of 0.18%,bulk density of 2.75 g·cm^(-3),firing shrinkage of 12.76%,bending strength reaching 101.93 MPa,and fracture toughness of 2.51 MPa·m^(1/2).As the amount ofα-Al_(2)O_(3) additive increased,the ceramic thin plates exhibited a greater abundance of short rod-like mullite and corundum grains,which were tightly packed together,forming a framework for the ceramic thin plates.This microstructure enhanced pathways for crack propagation,dispersed internal stresses,and increased fracture surface energy,resulting in significant improvements in both strength and fracture toughness of the ceramic thin plates.展开更多
We investigate the effects of projectile material on high-speed penetration/perforation of Inconel 718 alloy(IN718)plates.High-speed ballistic impact tests are conducted on 2 mm-thickness IN718 plates with 5-mm-diamet...We investigate the effects of projectile material on high-speed penetration/perforation of Inconel 718 alloy(IN718)plates.High-speed ballistic impact tests are conducted on 2 mm-thickness IN718 plates with 5-mm-diameter stainless steel 304(SS304),Ti alloy TC4,and Al alloy AA1060 spherical projectiles.The impact processes are captured with high-speed photography.Optical and scanning electron microscopy and laser scan are conducted on recovered projectiles and targets.Finite element models of the ballistic impact are established based on the coupled Eulerian-Lagrangian algorithm with the Johnson-Cook constitutive model and failure criterion,and can well reproduce the experimental results.The experimental and simulated data related to projectile dynamics,and the geometries of postmortem projectiles and bullet holes are analyzed with phenomenological models.Projectile velocity evolution can be described with hydrodynamic models of penetration.Dimensional analysis reveals a universal relationship between the bullet hole expansion coefficient and the normalized dynamic pressure,regardless of the projectile material.However,the projectile material does affect projectile deformation,bullet hole size,and energy absorption of target.展开更多
This paper aims to explore and quantify the nonlinear vibration response of tri-directional functionally graded sandwich(3D-FGSW)plates partially supported by a Pasternak foundation(PF)subjected to blast loading(BL).A...This paper aims to explore and quantify the nonlinear vibration response of tri-directional functionally graded sandwich(3D-FGSW)plates partially supported by a Pasternak foundation(PF)subjected to blast loading(BL).A key objective is to develop a computationally efficient finite element framework capable of accurately capturing the complex behavior of 3D-FGSW plates.The studied configuration features a two-dimensional functionally graded material(2D-FGM)core between two threedimensional functionally graded material(3D-FGM)face layers.Nonlinear geometric effects,including mid-plane stretching,are modeled using von K arm an-type assumptions,and the governing equations are formulated via Hamilton's principle within an improved first-order shear deformation theory(iFSDT).The accuracy and computational efficiency of the proposed method are validated through comparison with existing benchmark solutions.Subsequently,a comprehensive parametric study is carried out to examine the effects of geometric dimensions,material properties,foundation sizes,and boundary conditions(BCs)on the nonlinear vibration of 3D-FGSW plates.The findings of this work are expected to provide valuable insights for the design and manufacturing of advanced sandwich structures subjected to BL.展开更多
A design idea for single-component metamaterial plates is proposed to achieve the thermal stability of flexural wave bandgap by the perforated and pre-curved patterns.The band structure analysis suggests that perforat...A design idea for single-component metamaterial plates is proposed to achieve the thermal stability of flexural wave bandgap by the perforated and pre-curved patterns.The band structure analysis suggests that perforation can release part of the in-plane thermal expansion to weaken the softening effect of thermal stress.Introducing precurved components to the perforated structure will stop the decrement of the bandgap frequency in thermal environment,and even make the frequency higher with appropriate structural parameters.The bending stiffness of the heated plate is enhanced by the thermal deflection induced stiffening effect of the pre-curved components.The segmented pre-curved component presents a strong ability to resist the thermal influence on the flexural wave bandgap.A simplified model is established for the local structure of the precurved component.The theoretical calculations explain the thermally induced frequency increment of the bandgap and the discrepancy in the thermal response between the two pre-curved models.The transmittance of flexural wave validates the effectiveness of the proposed design.展开更多
A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The resu...A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The results show that cold-pressing produces intense plastic deformation near the corrugated surface of the Al plate,which promotes dynamic recrystallization of the Al substrate near the interface during the subsequent hot-pressing.In addition,the initial corrugation on the surface of the Al plate also changes the local stress state near the interface during hot pressing,which has a large effect on the texture components of the substrates near the corrugated interface.The construction of the corrugated interface can greatly enhance the shear strength by 2−4 times due to the increased contact area and the strong“mechanical gearing”effect.Moreover,the mechanical properties are largely depended on the orientation relationship between corrugated direction and loading direction.展开更多
Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The t...Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The traditional thermal elastic-plastic finite element method(TEP-FEM)can accurately predict welding deformation.However,its efficiency is low because of the complex nonlinear transient computation,making it difficult to meet the needs of rapid engineering evaluation.To address this challenge,this study proposes an efficient prediction method for welding deformation in marine thin plate butt welds.This method is based on the coupled temperature gradient-thermal strain method(TG-TSM)that integrates inherent strain theory with a shell element finite element model.The proposed method first extracts the distribution pattern and characteristic value of welding-induced inherent strain through TEP-FEM analysis.This strain is then converted into the equivalent thermal load applied to the shell element model for rapid computation.The proposed method-particularly,the gradual temperature gradient-thermal strain method(GTG-TSM)-achieved improved computational efficiency and consistent precision.Furthermore,the proposed method required much less computation time than the traditional TEP-FEM.Thus,this study lays the foundation for future prediction of welding deformation in more complex marine thin plates.展开更多
In order to investigate the penetration performance of Linear-Shaped Charge(LSC),Embowed LinearShaped Charge(ELSC),and Embowed Linear Explosively Formed Projectile(ELEFP)on T-shaped stiffened plates,a series of near-f...In order to investigate the penetration performance of Linear-Shaped Charge(LSC),Embowed LinearShaped Charge(ELSC),and Embowed Linear Explosively Formed Projectile(ELEFP)on T-shaped stiffened plates,a series of near-field air-burst experiments are conducted.The damage modes and characteristics of the target plates are compared and analyzed.Each flat plate section is completely punctured,resulting in a penetration hole.The damage modes induced by the three charge types on the stiffened plate structure are consistent,characterized by shear failure in the central region of the flat plate due to penetration by the penetrator,localized plastic deformation of the flat plate,and local penetration failure resulting from partial perforation of the central stiffener.The penetration lengths caused by ELSC and ELEFP are 45.1%and 46.1% larger than that of LSC,while the half-width of the penetration hole generated by ELEFP is 54.2% and 24.7% smaller than that of ELSC and LSC,respectively.The penetration height caused by ELEFP are 17.5%and 62.1% larger than that of ELSC and LSC,respectively.The stiffener effectively segments the damage area,enhancing the local structural strength and limiting the extent of plastic deformation in the flat plate section.The comparative results show that the ELSC proves to be more effective for efficient large-scale damage,and ELEFP is more suitable for achieving efficient localized damage.展开更多
[Background and purposes]Proton exchange membrane fuel cells(PEMFCs),which convert hydrogen energy directly into electrical energy and water,have received overwhelming attention,owing to their potential to significant...[Background and purposes]Proton exchange membrane fuel cells(PEMFCs),which convert hydrogen energy directly into electrical energy and water,have received overwhelming attention,owing to their potential to significantly reduce energy consumption,pollution emissions and reliance on fossil fuels.Bipolar plates are the major part and key component of PEMFCs stack,which provide mechanical strength,collect and conduct current segregate oxidants and reduce agents.They contribute 70-80%weight and 20-30%cost of a whole stack,while significantly affecting the power density.There are three types plates,including metal bipolar plate,graphite bipolar plate and composite bipolar plate.Stainless steel bipolar plates,as one of metal bipolar plate,exhibit promising manufacturability,competitive cost and durability among various metal materials.However,stainless steel would be corroded in the harsh acid(pH 2-5)and humid PEMFCs environment,whereas the leached ions will contaminate the membrane.In addition,the passivated film formed on the surface will increase the interfacial contact resistance(ICR).In order to improve the corrosion resistance and electrical conductivity of steel bipolar plates,surface coatings are essential.Metal nitride coatings,metal carbide coatings,polymer coatings and carbon-based coatings have been introduced in recent years.Carbon-based coatings,mainly including a-C(amorphous Carbon),Ta-C(Tetrahedral amorphous carbon)and DLC(diamond-like carbon),have attracted considerable attention from both academia and industry,owing to their superior performance,such as chemical inertness,mechanical hardness and electrical conductivity.However,Ta-C films as protective coating of PEMFCs have been rarely reported,due to the difficulty in production for industrial application.In this paper,multi-layer Ta-C composite films were produced by using customized industrial-scale vacuum equipment to address those issues.[Methods]Multiple layered Ta-C coatings were prepared by using PIS624 equipment,which assembled filtered cathodic arc evaporation,ion beam and magnetron sputtering into one equipment,while SS304 and silicon specimens were used as substrate for testing and analysis.Adhesion layer and intermediate layer were deposited by using magnetron sputtering at deposition temperature of 150℃and pressure of 3×10^(−1) Pa,while the sputtering current was set to be 5 A and bias power to be 300 V.The Ta-C layer was coated at arc current of 80-100 A,bias voltage of 1500 V and gas flow of 75 sccm.A scanning electron microscope(CIQTEK SEM3200)was used to characterize surface morphology,coating structure and cross-section profile of the coatings.Raman spectrometer(LabRam HR Evolution,HORIBA JOBIN YVON)was used to identify the bonding valence states.Electrochemical tests were performed by using an electrochemical work station(CHI760,Shanghai Chenhua Instrument Co.,Ltd.),with the traditional three electrode system,where saturated Ag/AgCl and platinum mesh were used as the reference electrode and counter electrode,respectively.All samples were mounted in plastic tube and sealed with epoxy resin,with an exposure area of 2.25 cm^(2),serving as the working electrode.Electrochemical measurements were carried out in simulated PEMFCs cathode environment in 0.5 mol·L^(−1) H_(2)SO_(4)+5 ppm F−solution,at operating temperature of 70℃.As the cathode environment was harsher than the anode environment,all the samples are stabilized at the open-circuit potential(OCP)for approximately 30 min before the EIS measurements.ICR between bipolar plates and GDL was a key parameter affecting performance of the PEMFCs stack.The test sample sandwiched between 2 pieces of carbon paper(simulate gas diffusion layer,GDL)was placed between 2 gold-plated copper electrodes at a compaction pressure of 1.4 MPa,which was considered to be the conventional compaction pressure in the PEMFCs.Under the same conditions,the resistance of a single carbon paper was measured as well.The ICR was calculated according to the formula ICR=1/2(R2−R1)×S,where S was the contact area between GDL and coated stainless steel BPPs.All data of ICR were measured three times for averaging.[Results]The coatings deposited by filtered cathodic arc technology were compact and smooth,which reduced coating porosity and favorable to corrosion resistance.The coating thickness of adhesion and intermediate layers were 180 nm,while the protective Ta-C coating thickness was about 300 nm,forming multiple coating to provide stronger protection for metal bipolar plates.Cr,Ti,Nb and Ta coatings were selected as adhesion layers for comparison.According to electrochemical test,Ta and Nb coatings have higher corrosion resistance.However,Ta and Nb materials would be costly when they are used for mass production.Relatively,Cr and Ti materials were cost effective.Hence,a comprehensive assessment was indispensable to decide the materials to be selected as adhesion layer.Ta-TiN and Ti-TiN combined adhesion and intermediate layer exhibited stronger corrosion resistance,with the corrosion current to be less than 10^(−6) A·cm^(−2).Ta-C protective coating deposited by using filtered cathodic arc technology indicated displayed higher corrosion resistance,with the average corrosion density to be about 1.26×10^(−7) A·cm^(−2).Ta-C coating also shown larger contact angle,with the highest hydrophobicity,which was one of the important advantages for Ta-C,in terms of corrosion resistance.According to Raman spectroscopy,the I(D)/I(G)=549.8/1126.7=0.487,with the estimated fraction of sp^(3) bonding to be in the range of 5154%.The intermediate layer TiN has higher conductivity than the CrN layer.Considering cost,corrosion performance and ICR result,the Ti-TiN layer combination is recommended for industrial scale application.[Conclusions]Multiple layer coating structure of Ta-C film had stronger corrosion resistance;with more than 50%sp^(3) content,while it also had larger water contact angle and higher corrosion resistance than DLC film.The filtered arcing deposition technology was able to make the film to be more consistent and stable than normal arcing technology in terms of the preparation of Ta-C.The coating displayed corrosion density of 1.26×10^(−7) A·cm^(−2) and ICR of less than 5 mΩ·cm^(2),far beyond technical target of 2025 DOE(US Department of Energy).This indicated that the mass-production scale coating technology for PEMFC bipolar plates is highly possible.展开更多
Since the initial observation of carbon nanotubes(CNTs)and graphene platelets(GPLs)in the 1990 and 2000s,the demand for high-performance structural applications and multifunctional materials has driven significant int...Since the initial observation of carbon nanotubes(CNTs)and graphene platelets(GPLs)in the 1990 and 2000s,the demand for high-performance structural applications and multifunctional materials has driven significant interest in composite structures reinforced with GPLs and CNTs.Incorporating these nanofillers into matrix materials markedly enhances the mechanical properties of the structures.To further improve efficiency and functionality,func-tionally graded(FG)distributions of CNTs and GPLs have been proposed.This study presents an extensive review of computational approaches developed to predict the global behavior of composite structural components enhanced with CNT and GPL nanofillers.The analysis focuses on key structural elements,such as plate-type configurations,cylindrical and curved shells,and beams,emphasizing the computational techniques utilized to simulate their mechanical behavior.The utilization of three-dimensional elasticity theories and equivalent single-layer(ESL)frameworks,which are widely employed in the modeling and analysis of these composites,is comprehensively discussed.Additionally,the paper examines various mechanical performance aspects,including static,buckling,post-buckling,vibrational,and dynamic responses for the mentioned structures.The unique features of hybrid nanocomposites,combining CNTs and GPLs,are also analyzed.Furthermore,the study delves into the fabrication and processing techniques of these materials,with a particular focus on strategies to mitigate nanofiller agglomeration.The review extends to cover thermal and electrical properties,durability under environmental exposure,fatigue resistance,and vibration-damping characteristics.In conclusion,the paper underscores the necessity for ongoing advancements in computational modeling to facilitate improved design,analysis,and optimization of nanocomposite structures.Future research opportunities in this rapidly advancing domain are also outlined.展开更多
Odd elasticity introduces active moduli to the antisymmetric components of the elastic tensor,which describe the asymmetric coupling between different deformation modes in a medium and quantify the work extracted duri...Odd elasticity introduces active moduli to the antisymmetric components of the elastic tensor,which describe the asymmetric coupling between different deformation modes in a medium and quantify the work extracted during quasi-static strain cycles.The introduction of active moduli renders the elastic tensor non-Hermitian,breaking the Maxwell-Betti reciprocity and enabling the observation of phenomena that cannot occur in traditional passive media.Here,we develop an analytical dynamic model for odd elastic circular plates to investigate the effects of odd elasticity on motion in rotationally symmetric geometries.We report a novel nonreciprocal rotating wave and explore the effects of different odd elastic moduli on chiral deformation.Nonreciprocal rotating waves represent a distinct dynamic mode,exhibiting unidirectional propagation with amplitude increasing or decreasing exclusively along a specific direction.The amplitude change during motion reveals the system’s non-conservation of energy.展开更多
Bipolar plates(BPs)are essential multifunctional components in vanadium redox flow batteries(VRFBs)that require excellent electrical conductivity,low permeability,and strong solid support for the stack.However,convent...Bipolar plates(BPs)are essential multifunctional components in vanadium redox flow batteries(VRFBs)that require excellent electrical conductivity,low permeability,and strong solid support for the stack.However,conventional BPs are based on graphite sheets,which provide mechanical properties and corrosion resistance but have limitations in terms of electrical conductivity.Although carbon nanotubes(CNTs)have excellent properties,CNT composites with low CNT volume fractions(10–20%)have increased electrolyte permeability and limited electrical conductivity improvement,resulting in low durability and efficiency for VRFBs.This study proposes a novel concept of horizontally aligned CNT nanocomposite bipolar plate(HACN-BP)to address these issues.The HACN-BPs feature an optimized conduction path with a CNT volume fraction of 59%,resulting in reduced manufacturing time while demonstrating superior conductivity and permeability compared to conventional BPs.Furthermore,integrated HACN-BP mitigates ohmic loss that occurs in the BPs,thereby mitigating the potential drop by 40%.Therefore,the utilization of HACN-BP shows superior performance compared to recent studies,a substantial improvement of more than 6%in energy efficiency and 14%in capacity over conventional BP.展开更多
BACKGROUND Simultanagnosia is a neurological disorder that impairs an individual's ability to perceive more than one object at a time visually.While the individual may acknowledge the presence of multiple objects ...BACKGROUND Simultanagnosia is a neurological disorder that impairs an individual's ability to perceive more than one object at a time visually.While the individual may acknowledge the presence of multiple objects in his field of view,he cannot generally summarize the overall percept.CASE SUMMARY We describe a case of simultanagnosia in Posterior Cortical Atrophy,evidenced by the Ishihara color test.A 54-year-old woman complained of reading problems despite normal visual acuity and a structural eye exam.The patient failed to identify any of the Ishihara color plates in either eye despite adequate naming of colors.Automated visual field testing showed a homonymous hemianopia.Structural and functional neuroimaging and cerebrospinal fluid analysis were consistent with posterior cortical atrophy.CONCLUSION Simultanagnosia can be tested with the Ishihara pseudoisochromatic plates because the recognition of embedded number patterns in the test requires appreciation of a collection of individual stimuli.展开更多
This paper presents a novel fully edge-based smoothed finite element method for free vibration analysis of functionally graded plates,incorporating a quasi-weak form of smoothed integral within an edge-based finite el...This paper presents a novel fully edge-based smoothed finite element method for free vibration analysis of functionally graded plates,incorporating a quasi-weak form of smoothed integral within an edge-based finite element method framework.Employing first-order shear deformation plate theory,the present method accounts for transverse shear strain and rotary inertia effects while addressing exponentially graded material properties along the plate thickness.The formulation integrates a three-node Mindlin plate element(MIN3)with a shear stabilization technique to prevent shear locking.The quasi-weak form of smoothed integral necessitates the evaluation of indefinite integrals for shape functions,effectively tacking domain integrals related to the shape functions without partial derivatives.By applying both quasi-weak form of smoothed integral and strain smoothing technique,all domain integrals in stiffness and mass matrices are converted into boundary integrals over smoothing domains.Therefore,isoparametric mapping and computing of Jacobian matrix are completely eliminated throughout the solution process.The natural frequencies obtained using the present method are in good agreement with those reported in the literature,highlighting the versatility of the present method for free vibration analysis of functionally graded plates.Notably,the present method demonstrates advantages in eliminating shear locking and reducing sensitivity to mesh distortion.展开更多
Characteristics of heat transfer and flow of Newtonian and non-Newtonian fluids through porous walls and in porous media are studied due to their wide range of applications including geothermal reservoirs,heat exchang...Characteristics of heat transfer and flow of Newtonian and non-Newtonian fluids through porous walls and in porous media are studied due to their wide range of applications including geothermal reservoirs,heat exchangers,marine propulsion,and aerodynamics.The current study investigates the characteristics of heat transport in a reactive third-grade fluid,moving through permeable parallel plates,with uniform suction/injection velocity.The two permeable,parallel plates are maintained at the same,constant temperature.After being transformed into its dimensionless equivalent,governing equations are solved by employing the Least Squares Method(LSM).The LSM results are further validated with numerical solutions for temperature and velocity.The impact of cross-flow Reynolds number,Peclet number,heat generation parameter,non-Newtonian parameter,and Brinkman number on entropy generation,velocity,temperature,and Bejan number are investigated.Theresults indicate that temperature distribution is significantly influenced by the third-grade fluid parameter.The maximum temperature drops from almost 0.12 to 0.10 as the third-grade fluid parameter increases from0.05 to 0.4.When the cross-flow Reynolds number is raised from 0.05 to 3,the maximum temperature drops from 0.12 to around 0.09.Temperature is strongly influenced by the heat generation parameter.A greater understanding of the thermal characteristics necessary for the design of a variety of systems,such as heat exchangers,marine propulsion,aerodynamic systems,etc.,may be gained from the findings of the current study.展开更多
This study proposes a three-dimensional(3D)coupled magneto-electro-elastic problem for the static analysis of multilayered plates embedding piezomagnetic and piezoelectric layers by considering both sensor and actuato...This study proposes a three-dimensional(3D)coupled magneto-electro-elastic problem for the static analysis of multilayered plates embedding piezomagnetic and piezoelectric layers by considering both sensor and actuator configurations.The 3D governing equations for the magneto-electro-elastic static behavior of plates are explicitly show that are made by the three 3D equilibrium equations,the 3D divergence equation for magnetic induction,and the 3D divergence equation for the electric displacement.The proposed solution involves the exponential matrix in the thickness direction and primary variables’harmonic forms in the in-plane ones.A closed-form solution is performed considering simply-supported boundary conditions.Interlaminar continuity conditions are imposed for displacements,magnetic potential,electric potential,transverse shear/normal stresses,transverse normal magnetic induction and transverse normal electric displacement.Therefore,a layerwise approach is adopted.The results section is composed of an assessment part,where the present model is compared to past 3D electro-elastic or magneto-elastic formulations and a new benchmark part.Benchmarks consider sensor and actuator plate configurations for the fully coupled magneto-electro-elastic cases for different thickness ratios.Tabular and graphical results are presented for displacements,stresses,magnetic potential,electric potential,transverse normal magnetic induction and transverse normal electric displacement.For each presented benchmark,magneto-electro-elastic coupling and thickness and material layer effects are discussed in depth.展开更多
A mesh-free method is presented to investigate the static bending properties of functionally graded carbon nanotube-reinforced composite(FG-CNTRC)plates.The curvature of the plate is directly interpolated with the nod...A mesh-free method is presented to investigate the static bending properties of functionally graded carbon nanotube-reinforced composite(FG-CNTRC)plates.The curvature of the plate is directly interpolated with the nodal deflections due to the higher-order continuity property of the moving leastsquares approximation,establishing a mesh-free computational scheme where the nodal deflections are the only unknowns.The convergence and efficiency of the proposed method are studied based on a homogeneous square plate.The FG-CNTRC plates are modeled with continuously varying Young’s moduli along the thickness direction according to the volume fraction of the carbon nanotubes(CNTs).Detailed studies have been conducted on the effects of different boundary conditions,CNT volume fractions,geometric shapes,and width-to-thickness ratios on bending behavior.CNT efficiency parameters are introduced to account for load transfer between the nanotubes and the matrix,treating the nanocomposites as orthotropic materials.However,in the actual structure,arranging the CNTs in the desired direction is more difficult compared to other fibers.Therefore,in the present study,CNTs in the composites are considered to be arranged randomly,resulting in the composite properties being treated as isotropic.The study includes second-order derivatives of deflections,and the finite element method typically requires C1 continuity for interpolation,which introduces challenges in building elements and constructing interpolation functions.The distinct advantage of the mesh-free method is that it requires only C0 weight functions.A mesh-free computational scheme based on moving leastsquares approximations for composite plates using Kirchhoffplate theory is established.Bending analyses of homogeneous and FG-CNTRC plates are conducted using the proposed method.Aspects such as boundary conditions,CNT volume fractions,geometric shapes,and width-to-thickness ratios are also discussed.Regular node arrangements and background meshes are adopted in the present study.Results are computed using different scalar parameters and numbers of nodes.Convergence properties for the central deflection of isotropic plates are analyzed in terms of the number of nodes and different scalar parameters.The normalized central deflection is defined and examined under various boundary conditions.展开更多
A three-dimensional(3D)analytical formulation is proposed to put together magnetic,electric and elastic fields to analyze the vibration modes of simply-supported layered piezo-electro-magnetic plates.The present 3D mo...A three-dimensional(3D)analytical formulation is proposed to put together magnetic,electric and elastic fields to analyze the vibration modes of simply-supported layered piezo-electro-magnetic plates.The present 3D model allows analyses for layered smart plates in both open-circuit and closed-circuit configurations.The secondorder differential equations written in the mixed curvilinear reference system govern the magneto-electro-elastic free vibration problem for multilayered plates.This set consists of the 3D equations of motion and the 3D divergence equations for the magnetic induction and electric displacement.Navier harmonic forms in the planar directions and the exponential matrix method in the transversal direction of the plate are applied to solve the second-order differential equations in terms of displacements.For these reasons,simply-supported boundary conditions are considered.Imposition of interlaminar continuity conditions on primary variables(displacements,magnetic potential,electric potential),and some secondary variables(transverse normal and transverse shear stresses,transverse normal magnetic induction/electric displacement)allows the implementation of the layer-wise approach.Assessments for both load boundary configurations are proposed in the results section to validate the present 3D approach.3D electro-elastic and 3D magneto-elastic coupling validations are performed separately considering different models from the open literature.A new benchmark involving a full magneto-electro-elastic coupling for multilayered plates is presented considering both load boundary configurations for different thickness ratios.For this benchmark,circular frequency values and related vibration modes through the transverse direction in terms of displacements,magnetic and electric potential,transverse normal magnetic induction/electric displacement are shown to visualize the magneto-electroelastic coupling and material and thickness layer effects.The present formulation has been entirely implemented in an academic Matlab(R2024a)code developed by the authors.In this paper,for the first time,the second-order differential equations governing the magneto-electro-elastic problem for the free vibration analysis of plates has been solved considering the mixed mode of harmonic forms and exponential matrix.The exponential matrix permits computing the secondary variable of the problem(stresses,electric displacement components and magnetic induction components)exactly,directly from constitutive and geometrical equations.In addition,the very simple and elegant formulation permits having a code with very low computational costs.The present manuscript aims to fill the void in open literature regarding reference 3D solutions for the free vibration analysis of magneto-electro-elastic plates.展开更多
In the fabrication and monitoring of parts in composite structures,which are being used more and more in a variety of engineering applications,the prediction and fatigue failure detection in composite materials is a d...In the fabrication and monitoring of parts in composite structures,which are being used more and more in a variety of engineering applications,the prediction and fatigue failure detection in composite materials is a difficult problem.This difficulty arises from several factors,such as the lack of a comprehensive investigation of the fatigue failure phenomena,the lack of a well-defined fatigue damage theory used for fatigue damage prediction,and the inhomogeneity of composites because of their multiple internal borders.This study investigates the fatigue behavior of carbon fiber reinforced with epoxy(CFRE)laminated composite plates under spectrum loading utilizing a uniqueDeep LearningNetwork consisting of a convolutional neural network(CNN).Themethod includes establishing Finite Element Model(FEM)in a plate model under a spectrum fatigue loading.Then,a CNN is trained for fatigue behavior prediction.The training phase produces promising results,showing the model’s performance with 94.21%accuracy,92.63%regression,and 91.55%F-score.To evaluate the model’s reliability,a comparison is made between fatigue data from the CNN and the FEM.It was found that the error band for this comparison is less than 0.3878MPa,affirming the accuracy and reliability of the proposed technique.The proposed method results converge with available experimental results in the literature,thus,the study suggests the broad applicability of this method to other different composite structures.展开更多
Installing the splitter plates is a passive aerodynamic solution for eliminating vortex-induced vibration (VIV). However, the influences of splitter plates on the VIV and aerostatic performances are more complicated d...Installing the splitter plates is a passive aerodynamic solution for eliminating vortex-induced vibration (VIV). However, the influences of splitter plates on the VIV and aerostatic performances are more complicated due to aerodynamic interference between highway and railway decks. To study the effects of splitter plates, wind tunnel experiments for measuring VIV and aerostatic forces of twin decks under two opposite flow directions were conducted, while the surrounding flow and wind pressure of static twin decks with and without splitter plates are numerically simulated. The results showed that the incoming flow direction affects the VIV response and aerostatic coefficients. The highway deck has poor vertical and torsional VIV, and the VIV region and amplitude are different under different directions. While the railway deck only has vertical VIV when located upstream. The splitter plates can impede the process of vortex generation, shedding and impinging at the gap between twin deck, and significantly reducing the surface fluctuating pressure coefficient, thus effectively suppressing the VIV of twin decks. While, the splitter plates hurt the upstream deck regarding static wind stability and have little effect on the downstream deck. The splitter plates of appropriate width are recommended to improve VIV performances in twin parallel bridges.展开更多
Legendre polynomial method is well-known in modeling acoustic wave characteristics.This method uses for the mechanical displacements a single polynomial expansion over the entire sandwich layers.This results in a limi...Legendre polynomial method is well-known in modeling acoustic wave characteristics.This method uses for the mechanical displacements a single polynomial expansion over the entire sandwich layers.This results in a limitation in the accuracy of the field profile restitution.Thus,it can deal with the guided waves in layered sandwich only when the material properties of adjacent layers do not change significantly.Despite the great efforts regarding this issue in the literature,there remain open questions.One of them is:“what is the exact threshold of contrasting material properties of adjacent layers for which this polynomial method cannot correctly restitute the roots of guided waves?”We investigated this numerical issue using the calculated guided phase velocities in 0°/φ/0°-carbon fibre reinforced plastics(CFRP)sandwich plates with gradually increasing angleφ.Then,we approached this numerical problem by varying the middle layer thickness h90°for the 0°/90°/0°-CFRP sandwich structure,and we proposed an exact thickness threshold of the middle layer for the Legendre polynomial method limitations.We showed that the polynomial method fails to calculate the quasi-symmetric Lamb mode in 0°/φ/0°-CFRP whenφ>25°.Moreover,we introduced a new Lamb mode so-called minimum-group-velocity that has never been addressed in literature.展开更多
基金Funded by the National Key Technology Research and Development Program of the Ministry of Science and Technology of China(No.2023YFB4204302)。
文摘Ceramic thin plates were prepared using kaolin,potassium sodium feldspar and quartz powder as the main raw materials and kaolin,α-Al_(2)O_(3),MoO_(3) and AlF_(3)·3H_(2)O as additives.The experiment examined the effects of different additives on mullite formation,as well as the microstructure and properties of the ceramic thin plates.Additionally,the study explored the toughening and strengthening mechanisms induced by the additives,providing a theoretical foundation for further optimizing the toughness of ceramic thin plates.The results showed that the D4 sample fired at 1220℃(with an addition of 20 wt% α-Al_(2)O_(3))exhibited the best performance,with a water absorption rate of 0.07%,apparent porosity of 0.18%,bulk density of 2.75 g·cm^(-3),firing shrinkage of 12.76%,bending strength reaching 101.93 MPa,and fracture toughness of 2.51 MPa·m^(1/2).As the amount ofα-Al_(2)O_(3) additive increased,the ceramic thin plates exhibited a greater abundance of short rod-like mullite and corundum grains,which were tightly packed together,forming a framework for the ceramic thin plates.This microstructure enhanced pathways for crack propagation,dispersed internal stresses,and increased fracture surface energy,resulting in significant improvements in both strength and fracture toughness of the ceramic thin plates.
基金supported by National Natural Science Foundation of China(No.12402465)Sichuan Science and Technology Program(No.2023NSFSC1284)。
文摘We investigate the effects of projectile material on high-speed penetration/perforation of Inconel 718 alloy(IN718)plates.High-speed ballistic impact tests are conducted on 2 mm-thickness IN718 plates with 5-mm-diameter stainless steel 304(SS304),Ti alloy TC4,and Al alloy AA1060 spherical projectiles.The impact processes are captured with high-speed photography.Optical and scanning electron microscopy and laser scan are conducted on recovered projectiles and targets.Finite element models of the ballistic impact are established based on the coupled Eulerian-Lagrangian algorithm with the Johnson-Cook constitutive model and failure criterion,and can well reproduce the experimental results.The experimental and simulated data related to projectile dynamics,and the geometries of postmortem projectiles and bullet holes are analyzed with phenomenological models.Projectile velocity evolution can be described with hydrodynamic models of penetration.Dimensional analysis reveals a universal relationship between the bullet hole expansion coefficient and the normalized dynamic pressure,regardless of the projectile material.However,the projectile material does affect projectile deformation,bullet hole size,and energy absorption of target.
文摘This paper aims to explore and quantify the nonlinear vibration response of tri-directional functionally graded sandwich(3D-FGSW)plates partially supported by a Pasternak foundation(PF)subjected to blast loading(BL).A key objective is to develop a computationally efficient finite element framework capable of accurately capturing the complex behavior of 3D-FGSW plates.The studied configuration features a two-dimensional functionally graded material(2D-FGM)core between two threedimensional functionally graded material(3D-FGM)face layers.Nonlinear geometric effects,including mid-plane stretching,are modeled using von K arm an-type assumptions,and the governing equations are formulated via Hamilton's principle within an improved first-order shear deformation theory(iFSDT).The accuracy and computational efficiency of the proposed method are validated through comparison with existing benchmark solutions.Subsequently,a comprehensive parametric study is carried out to examine the effects of geometric dimensions,material properties,foundation sizes,and boundary conditions(BCs)on the nonlinear vibration of 3D-FGSW plates.The findings of this work are expected to provide valuable insights for the design and manufacturing of advanced sandwich structures subjected to BL.
基金Project supported by the National Natural Science Foundation of China(Nos.12102321 and 52192633)the Natural Science Basic Research Plan in Shaanxi Province of China(No.2025JCYBMS-050)。
文摘A design idea for single-component metamaterial plates is proposed to achieve the thermal stability of flexural wave bandgap by the perforated and pre-curved patterns.The band structure analysis suggests that perforation can release part of the in-plane thermal expansion to weaken the softening effect of thermal stress.Introducing precurved components to the perforated structure will stop the decrement of the bandgap frequency in thermal environment,and even make the frequency higher with appropriate structural parameters.The bending stiffness of the heated plate is enhanced by the thermal deflection induced stiffening effect of the pre-curved components.The segmented pre-curved component presents a strong ability to resist the thermal influence on the flexural wave bandgap.A simplified model is established for the local structure of the precurved component.The theoretical calculations explain the thermally induced frequency increment of the bandgap and the discrepancy in the thermal response between the two pre-curved models.The transmittance of flexural wave validates the effectiveness of the proposed design.
基金supported by Guangdong Major Project of Basic and Applied Basic Research, China (No. 2020B0301030006)Fundamental Research Funds for the Central Universities, China (No. SWU-XDJH202313)+1 种基金Chongqing Postdoctoral Science Foundation Funded Project, China (No. 2112012728014435)the Chongqing Postgraduate Research and Innovation Project, China (No. CYS23197)。
文摘A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The results show that cold-pressing produces intense plastic deformation near the corrugated surface of the Al plate,which promotes dynamic recrystallization of the Al substrate near the interface during the subsequent hot-pressing.In addition,the initial corrugation on the surface of the Al plate also changes the local stress state near the interface during hot pressing,which has a large effect on the texture components of the substrates near the corrugated interface.The construction of the corrugated interface can greatly enhance the shear strength by 2−4 times due to the increased contact area and the strong“mechanical gearing”effect.Moreover,the mechanical properties are largely depended on the orientation relationship between corrugated direction and loading direction.
基金Supported by the National Natural Science Foundation of China under Grant No.51975138the High-Tech Ship Scientific Research Project from the Ministry of Industry and Information Technology under Grant No.CJ05N20the National Defense Basic Research Project under Grant No.JCKY2023604C006.
文摘Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The traditional thermal elastic-plastic finite element method(TEP-FEM)can accurately predict welding deformation.However,its efficiency is low because of the complex nonlinear transient computation,making it difficult to meet the needs of rapid engineering evaluation.To address this challenge,this study proposes an efficient prediction method for welding deformation in marine thin plate butt welds.This method is based on the coupled temperature gradient-thermal strain method(TG-TSM)that integrates inherent strain theory with a shell element finite element model.The proposed method first extracts the distribution pattern and characteristic value of welding-induced inherent strain through TEP-FEM analysis.This strain is then converted into the equivalent thermal load applied to the shell element model for rapid computation.The proposed method-particularly,the gradual temperature gradient-thermal strain method(GTG-TSM)-achieved improved computational efficiency and consistent precision.Furthermore,the proposed method required much less computation time than the traditional TEP-FEM.Thus,this study lays the foundation for future prediction of welding deformation in more complex marine thin plates.
基金supported by the National Natural Science Foundation of China(Grant Nos.52271307,52061135107,52192692,11802025)the Liao Ning Excellent Youth Fund Program(Grant No.2023JH3/10200012)+1 种基金the Liao Ning Revitalization Tal-ents Program(Grant No.XLYC1908027)the Fundamental Research Funds for the Central Universities(Grant Nos.DUT20RC(3)025,DUT20TD108,DUT20LAB308)。
文摘In order to investigate the penetration performance of Linear-Shaped Charge(LSC),Embowed LinearShaped Charge(ELSC),and Embowed Linear Explosively Formed Projectile(ELEFP)on T-shaped stiffened plates,a series of near-field air-burst experiments are conducted.The damage modes and characteristics of the target plates are compared and analyzed.Each flat plate section is completely punctured,resulting in a penetration hole.The damage modes induced by the three charge types on the stiffened plate structure are consistent,characterized by shear failure in the central region of the flat plate due to penetration by the penetrator,localized plastic deformation of the flat plate,and local penetration failure resulting from partial perforation of the central stiffener.The penetration lengths caused by ELSC and ELEFP are 45.1%and 46.1% larger than that of LSC,while the half-width of the penetration hole generated by ELEFP is 54.2% and 24.7% smaller than that of ELSC and LSC,respectively.The penetration height caused by ELEFP are 17.5%and 62.1% larger than that of ELSC and LSC,respectively.The stiffener effectively segments the damage area,enhancing the local structural strength and limiting the extent of plastic deformation in the flat plate section.The comparative results show that the ELSC proves to be more effective for efficient large-scale damage,and ELEFP is more suitable for achieving efficient localized damage.
基金Major Science and technology projects of Anhui Province (202103a05020003)。
文摘[Background and purposes]Proton exchange membrane fuel cells(PEMFCs),which convert hydrogen energy directly into electrical energy and water,have received overwhelming attention,owing to their potential to significantly reduce energy consumption,pollution emissions and reliance on fossil fuels.Bipolar plates are the major part and key component of PEMFCs stack,which provide mechanical strength,collect and conduct current segregate oxidants and reduce agents.They contribute 70-80%weight and 20-30%cost of a whole stack,while significantly affecting the power density.There are three types plates,including metal bipolar plate,graphite bipolar plate and composite bipolar plate.Stainless steel bipolar plates,as one of metal bipolar plate,exhibit promising manufacturability,competitive cost and durability among various metal materials.However,stainless steel would be corroded in the harsh acid(pH 2-5)and humid PEMFCs environment,whereas the leached ions will contaminate the membrane.In addition,the passivated film formed on the surface will increase the interfacial contact resistance(ICR).In order to improve the corrosion resistance and electrical conductivity of steel bipolar plates,surface coatings are essential.Metal nitride coatings,metal carbide coatings,polymer coatings and carbon-based coatings have been introduced in recent years.Carbon-based coatings,mainly including a-C(amorphous Carbon),Ta-C(Tetrahedral amorphous carbon)and DLC(diamond-like carbon),have attracted considerable attention from both academia and industry,owing to their superior performance,such as chemical inertness,mechanical hardness and electrical conductivity.However,Ta-C films as protective coating of PEMFCs have been rarely reported,due to the difficulty in production for industrial application.In this paper,multi-layer Ta-C composite films were produced by using customized industrial-scale vacuum equipment to address those issues.[Methods]Multiple layered Ta-C coatings were prepared by using PIS624 equipment,which assembled filtered cathodic arc evaporation,ion beam and magnetron sputtering into one equipment,while SS304 and silicon specimens were used as substrate for testing and analysis.Adhesion layer and intermediate layer were deposited by using magnetron sputtering at deposition temperature of 150℃and pressure of 3×10^(−1) Pa,while the sputtering current was set to be 5 A and bias power to be 300 V.The Ta-C layer was coated at arc current of 80-100 A,bias voltage of 1500 V and gas flow of 75 sccm.A scanning electron microscope(CIQTEK SEM3200)was used to characterize surface morphology,coating structure and cross-section profile of the coatings.Raman spectrometer(LabRam HR Evolution,HORIBA JOBIN YVON)was used to identify the bonding valence states.Electrochemical tests were performed by using an electrochemical work station(CHI760,Shanghai Chenhua Instrument Co.,Ltd.),with the traditional three electrode system,where saturated Ag/AgCl and platinum mesh were used as the reference electrode and counter electrode,respectively.All samples were mounted in plastic tube and sealed with epoxy resin,with an exposure area of 2.25 cm^(2),serving as the working electrode.Electrochemical measurements were carried out in simulated PEMFCs cathode environment in 0.5 mol·L^(−1) H_(2)SO_(4)+5 ppm F−solution,at operating temperature of 70℃.As the cathode environment was harsher than the anode environment,all the samples are stabilized at the open-circuit potential(OCP)for approximately 30 min before the EIS measurements.ICR between bipolar plates and GDL was a key parameter affecting performance of the PEMFCs stack.The test sample sandwiched between 2 pieces of carbon paper(simulate gas diffusion layer,GDL)was placed between 2 gold-plated copper electrodes at a compaction pressure of 1.4 MPa,which was considered to be the conventional compaction pressure in the PEMFCs.Under the same conditions,the resistance of a single carbon paper was measured as well.The ICR was calculated according to the formula ICR=1/2(R2−R1)×S,where S was the contact area between GDL and coated stainless steel BPPs.All data of ICR were measured three times for averaging.[Results]The coatings deposited by filtered cathodic arc technology were compact and smooth,which reduced coating porosity and favorable to corrosion resistance.The coating thickness of adhesion and intermediate layers were 180 nm,while the protective Ta-C coating thickness was about 300 nm,forming multiple coating to provide stronger protection for metal bipolar plates.Cr,Ti,Nb and Ta coatings were selected as adhesion layers for comparison.According to electrochemical test,Ta and Nb coatings have higher corrosion resistance.However,Ta and Nb materials would be costly when they are used for mass production.Relatively,Cr and Ti materials were cost effective.Hence,a comprehensive assessment was indispensable to decide the materials to be selected as adhesion layer.Ta-TiN and Ti-TiN combined adhesion and intermediate layer exhibited stronger corrosion resistance,with the corrosion current to be less than 10^(−6) A·cm^(−2).Ta-C protective coating deposited by using filtered cathodic arc technology indicated displayed higher corrosion resistance,with the average corrosion density to be about 1.26×10^(−7) A·cm^(−2).Ta-C coating also shown larger contact angle,with the highest hydrophobicity,which was one of the important advantages for Ta-C,in terms of corrosion resistance.According to Raman spectroscopy,the I(D)/I(G)=549.8/1126.7=0.487,with the estimated fraction of sp^(3) bonding to be in the range of 5154%.The intermediate layer TiN has higher conductivity than the CrN layer.Considering cost,corrosion performance and ICR result,the Ti-TiN layer combination is recommended for industrial scale application.[Conclusions]Multiple layer coating structure of Ta-C film had stronger corrosion resistance;with more than 50%sp^(3) content,while it also had larger water contact angle and higher corrosion resistance than DLC film.The filtered arcing deposition technology was able to make the film to be more consistent and stable than normal arcing technology in terms of the preparation of Ta-C.The coating displayed corrosion density of 1.26×10^(−7) A·cm^(−2) and ICR of less than 5 mΩ·cm^(2),far beyond technical target of 2025 DOE(US Department of Energy).This indicated that the mass-production scale coating technology for PEMFC bipolar plates is highly possible.
文摘Since the initial observation of carbon nanotubes(CNTs)and graphene platelets(GPLs)in the 1990 and 2000s,the demand for high-performance structural applications and multifunctional materials has driven significant interest in composite structures reinforced with GPLs and CNTs.Incorporating these nanofillers into matrix materials markedly enhances the mechanical properties of the structures.To further improve efficiency and functionality,func-tionally graded(FG)distributions of CNTs and GPLs have been proposed.This study presents an extensive review of computational approaches developed to predict the global behavior of composite structural components enhanced with CNT and GPL nanofillers.The analysis focuses on key structural elements,such as plate-type configurations,cylindrical and curved shells,and beams,emphasizing the computational techniques utilized to simulate their mechanical behavior.The utilization of three-dimensional elasticity theories and equivalent single-layer(ESL)frameworks,which are widely employed in the modeling and analysis of these composites,is comprehensively discussed.Additionally,the paper examines various mechanical performance aspects,including static,buckling,post-buckling,vibrational,and dynamic responses for the mentioned structures.The unique features of hybrid nanocomposites,combining CNTs and GPLs,are also analyzed.Furthermore,the study delves into the fabrication and processing techniques of these materials,with a particular focus on strategies to mitigate nanofiller agglomeration.The review extends to cover thermal and electrical properties,durability under environmental exposure,fatigue resistance,and vibration-damping characteristics.In conclusion,the paper underscores the necessity for ongoing advancements in computational modeling to facilitate improved design,analysis,and optimization of nanocomposite structures.Future research opportunities in this rapidly advancing domain are also outlined.
基金The Innovative Projects of Key Disciplines of Civil Engineering of Changsha University of Science and Technology,24ZDXK07,Andi Lai。
文摘Odd elasticity introduces active moduli to the antisymmetric components of the elastic tensor,which describe the asymmetric coupling between different deformation modes in a medium and quantify the work extracted during quasi-static strain cycles.The introduction of active moduli renders the elastic tensor non-Hermitian,breaking the Maxwell-Betti reciprocity and enabling the observation of phenomena that cannot occur in traditional passive media.Here,we develop an analytical dynamic model for odd elastic circular plates to investigate the effects of odd elasticity on motion in rotationally symmetric geometries.We report a novel nonreciprocal rotating wave and explore the effects of different odd elastic moduli on chiral deformation.Nonreciprocal rotating waves represent a distinct dynamic mode,exhibiting unidirectional propagation with amplitude increasing or decreasing exclusively along a specific direction.The amplitude change during motion reveals the system’s non-conservation of energy.
基金supported by the Nano&Material Technology Development Program through the National R&D Program through the National Research Foundation of Korea(NRF)funded by the Ministry of Science and ICT(RS-202300260461).
文摘Bipolar plates(BPs)are essential multifunctional components in vanadium redox flow batteries(VRFBs)that require excellent electrical conductivity,low permeability,and strong solid support for the stack.However,conventional BPs are based on graphite sheets,which provide mechanical properties and corrosion resistance but have limitations in terms of electrical conductivity.Although carbon nanotubes(CNTs)have excellent properties,CNT composites with low CNT volume fractions(10–20%)have increased electrolyte permeability and limited electrical conductivity improvement,resulting in low durability and efficiency for VRFBs.This study proposes a novel concept of horizontally aligned CNT nanocomposite bipolar plate(HACN-BP)to address these issues.The HACN-BPs feature an optimized conduction path with a CNT volume fraction of 59%,resulting in reduced manufacturing time while demonstrating superior conductivity and permeability compared to conventional BPs.Furthermore,integrated HACN-BP mitigates ohmic loss that occurs in the BPs,thereby mitigating the potential drop by 40%.Therefore,the utilization of HACN-BP shows superior performance compared to recent studies,a substantial improvement of more than 6%in energy efficiency and 14%in capacity over conventional BP.
文摘BACKGROUND Simultanagnosia is a neurological disorder that impairs an individual's ability to perceive more than one object at a time visually.While the individual may acknowledge the presence of multiple objects in his field of view,he cannot generally summarize the overall percept.CASE SUMMARY We describe a case of simultanagnosia in Posterior Cortical Atrophy,evidenced by the Ishihara color test.A 54-year-old woman complained of reading problems despite normal visual acuity and a structural eye exam.The patient failed to identify any of the Ishihara color plates in either eye despite adequate naming of colors.Automated visual field testing showed a homonymous hemianopia.Structural and functional neuroimaging and cerebrospinal fluid analysis were consistent with posterior cortical atrophy.CONCLUSION Simultanagnosia can be tested with the Ishihara pseudoisochromatic plates because the recognition of embedded number patterns in the test requires appreciation of a collection of individual stimuli.
基金financial support from the National Natural Science Foundation of China(12172131,12162014)the Jiangxi Provincial Cultivation Program for Academic and Technical Leaders of Major Subjects(20225BCJ22010)are gratefully acknowledged.
文摘This paper presents a novel fully edge-based smoothed finite element method for free vibration analysis of functionally graded plates,incorporating a quasi-weak form of smoothed integral within an edge-based finite element method framework.Employing first-order shear deformation plate theory,the present method accounts for transverse shear strain and rotary inertia effects while addressing exponentially graded material properties along the plate thickness.The formulation integrates a three-node Mindlin plate element(MIN3)with a shear stabilization technique to prevent shear locking.The quasi-weak form of smoothed integral necessitates the evaluation of indefinite integrals for shape functions,effectively tacking domain integrals related to the shape functions without partial derivatives.By applying both quasi-weak form of smoothed integral and strain smoothing technique,all domain integrals in stiffness and mass matrices are converted into boundary integrals over smoothing domains.Therefore,isoparametric mapping and computing of Jacobian matrix are completely eliminated throughout the solution process.The natural frequencies obtained using the present method are in good agreement with those reported in the literature,highlighting the versatility of the present method for free vibration analysis of functionally graded plates.Notably,the present method demonstrates advantages in eliminating shear locking and reducing sensitivity to mesh distortion.
文摘Characteristics of heat transfer and flow of Newtonian and non-Newtonian fluids through porous walls and in porous media are studied due to their wide range of applications including geothermal reservoirs,heat exchangers,marine propulsion,and aerodynamics.The current study investigates the characteristics of heat transport in a reactive third-grade fluid,moving through permeable parallel plates,with uniform suction/injection velocity.The two permeable,parallel plates are maintained at the same,constant temperature.After being transformed into its dimensionless equivalent,governing equations are solved by employing the Least Squares Method(LSM).The LSM results are further validated with numerical solutions for temperature and velocity.The impact of cross-flow Reynolds number,Peclet number,heat generation parameter,non-Newtonian parameter,and Brinkman number on entropy generation,velocity,temperature,and Bejan number are investigated.Theresults indicate that temperature distribution is significantly influenced by the third-grade fluid parameter.The maximum temperature drops from almost 0.12 to 0.10 as the third-grade fluid parameter increases from0.05 to 0.4.When the cross-flow Reynolds number is raised from 0.05 to 3,the maximum temperature drops from 0.12 to around 0.09.Temperature is strongly influenced by the heat generation parameter.A greater understanding of the thermal characteristics necessary for the design of a variety of systems,such as heat exchangers,marine propulsion,aerodynamic systems,etc.,may be gained from the findings of the current study.
文摘This study proposes a three-dimensional(3D)coupled magneto-electro-elastic problem for the static analysis of multilayered plates embedding piezomagnetic and piezoelectric layers by considering both sensor and actuator configurations.The 3D governing equations for the magneto-electro-elastic static behavior of plates are explicitly show that are made by the three 3D equilibrium equations,the 3D divergence equation for magnetic induction,and the 3D divergence equation for the electric displacement.The proposed solution involves the exponential matrix in the thickness direction and primary variables’harmonic forms in the in-plane ones.A closed-form solution is performed considering simply-supported boundary conditions.Interlaminar continuity conditions are imposed for displacements,magnetic potential,electric potential,transverse shear/normal stresses,transverse normal magnetic induction and transverse normal electric displacement.Therefore,a layerwise approach is adopted.The results section is composed of an assessment part,where the present model is compared to past 3D electro-elastic or magneto-elastic formulations and a new benchmark part.Benchmarks consider sensor and actuator plate configurations for the fully coupled magneto-electro-elastic cases for different thickness ratios.Tabular and graphical results are presented for displacements,stresses,magnetic potential,electric potential,transverse normal magnetic induction and transverse normal electric displacement.For each presented benchmark,magneto-electro-elastic coupling and thickness and material layer effects are discussed in depth.
基金supported by the National Natural Science Foundation of China(No.52374110)Key scientific and technological projects of Henan province(No.242102320337)Basic Research Fund of Zhongyuan University of Technology(No.K2022QN008).
文摘A mesh-free method is presented to investigate the static bending properties of functionally graded carbon nanotube-reinforced composite(FG-CNTRC)plates.The curvature of the plate is directly interpolated with the nodal deflections due to the higher-order continuity property of the moving leastsquares approximation,establishing a mesh-free computational scheme where the nodal deflections are the only unknowns.The convergence and efficiency of the proposed method are studied based on a homogeneous square plate.The FG-CNTRC plates are modeled with continuously varying Young’s moduli along the thickness direction according to the volume fraction of the carbon nanotubes(CNTs).Detailed studies have been conducted on the effects of different boundary conditions,CNT volume fractions,geometric shapes,and width-to-thickness ratios on bending behavior.CNT efficiency parameters are introduced to account for load transfer between the nanotubes and the matrix,treating the nanocomposites as orthotropic materials.However,in the actual structure,arranging the CNTs in the desired direction is more difficult compared to other fibers.Therefore,in the present study,CNTs in the composites are considered to be arranged randomly,resulting in the composite properties being treated as isotropic.The study includes second-order derivatives of deflections,and the finite element method typically requires C1 continuity for interpolation,which introduces challenges in building elements and constructing interpolation functions.The distinct advantage of the mesh-free method is that it requires only C0 weight functions.A mesh-free computational scheme based on moving leastsquares approximations for composite plates using Kirchhoffplate theory is established.Bending analyses of homogeneous and FG-CNTRC plates are conducted using the proposed method.Aspects such as boundary conditions,CNT volume fractions,geometric shapes,and width-to-thickness ratios are also discussed.Regular node arrangements and background meshes are adopted in the present study.Results are computed using different scalar parameters and numbers of nodes.Convergence properties for the central deflection of isotropic plates are analyzed in terms of the number of nodes and different scalar parameters.The normalized central deflection is defined and examined under various boundary conditions.
文摘A three-dimensional(3D)analytical formulation is proposed to put together magnetic,electric and elastic fields to analyze the vibration modes of simply-supported layered piezo-electro-magnetic plates.The present 3D model allows analyses for layered smart plates in both open-circuit and closed-circuit configurations.The secondorder differential equations written in the mixed curvilinear reference system govern the magneto-electro-elastic free vibration problem for multilayered plates.This set consists of the 3D equations of motion and the 3D divergence equations for the magnetic induction and electric displacement.Navier harmonic forms in the planar directions and the exponential matrix method in the transversal direction of the plate are applied to solve the second-order differential equations in terms of displacements.For these reasons,simply-supported boundary conditions are considered.Imposition of interlaminar continuity conditions on primary variables(displacements,magnetic potential,electric potential),and some secondary variables(transverse normal and transverse shear stresses,transverse normal magnetic induction/electric displacement)allows the implementation of the layer-wise approach.Assessments for both load boundary configurations are proposed in the results section to validate the present 3D approach.3D electro-elastic and 3D magneto-elastic coupling validations are performed separately considering different models from the open literature.A new benchmark involving a full magneto-electro-elastic coupling for multilayered plates is presented considering both load boundary configurations for different thickness ratios.For this benchmark,circular frequency values and related vibration modes through the transverse direction in terms of displacements,magnetic and electric potential,transverse normal magnetic induction/electric displacement are shown to visualize the magneto-electroelastic coupling and material and thickness layer effects.The present formulation has been entirely implemented in an academic Matlab(R2024a)code developed by the authors.In this paper,for the first time,the second-order differential equations governing the magneto-electro-elastic problem for the free vibration analysis of plates has been solved considering the mixed mode of harmonic forms and exponential matrix.The exponential matrix permits computing the secondary variable of the problem(stresses,electric displacement components and magnetic induction components)exactly,directly from constitutive and geometrical equations.In addition,the very simple and elegant formulation permits having a code with very low computational costs.The present manuscript aims to fill the void in open literature regarding reference 3D solutions for the free vibration analysis of magneto-electro-elastic plates.
文摘In the fabrication and monitoring of parts in composite structures,which are being used more and more in a variety of engineering applications,the prediction and fatigue failure detection in composite materials is a difficult problem.This difficulty arises from several factors,such as the lack of a comprehensive investigation of the fatigue failure phenomena,the lack of a well-defined fatigue damage theory used for fatigue damage prediction,and the inhomogeneity of composites because of their multiple internal borders.This study investigates the fatigue behavior of carbon fiber reinforced with epoxy(CFRE)laminated composite plates under spectrum loading utilizing a uniqueDeep LearningNetwork consisting of a convolutional neural network(CNN).Themethod includes establishing Finite Element Model(FEM)in a plate model under a spectrum fatigue loading.Then,a CNN is trained for fatigue behavior prediction.The training phase produces promising results,showing the model’s performance with 94.21%accuracy,92.63%regression,and 91.55%F-score.To evaluate the model’s reliability,a comparison is made between fatigue data from the CNN and the FEM.It was found that the error band for this comparison is less than 0.3878MPa,affirming the accuracy and reliability of the proposed technique.The proposed method results converge with available experimental results in the literature,thus,the study suggests the broad applicability of this method to other different composite structures.
基金Projects(51925808,52078504,51822803) supported by the National Natural Science Foundation of ChinaProject(2022JJ10082) supported by the Natural Science Foundation of Hunan Province,China+1 种基金Project(N2022Z004) supported by the Research on Technology Development Trend and Key Common Problems in Railway,ChinaProject(Xplorer Prize 2021) supported by the Tencent Foundation,China。
文摘Installing the splitter plates is a passive aerodynamic solution for eliminating vortex-induced vibration (VIV). However, the influences of splitter plates on the VIV and aerostatic performances are more complicated due to aerodynamic interference between highway and railway decks. To study the effects of splitter plates, wind tunnel experiments for measuring VIV and aerostatic forces of twin decks under two opposite flow directions were conducted, while the surrounding flow and wind pressure of static twin decks with and without splitter plates are numerically simulated. The results showed that the incoming flow direction affects the VIV response and aerostatic coefficients. The highway deck has poor vertical and torsional VIV, and the VIV region and amplitude are different under different directions. While the railway deck only has vertical VIV when located upstream. The splitter plates can impede the process of vortex generation, shedding and impinging at the gap between twin deck, and significantly reducing the surface fluctuating pressure coefficient, thus effectively suppressing the VIV of twin decks. While, the splitter plates hurt the upstream deck regarding static wind stability and have little effect on the downstream deck. The splitter plates of appropriate width are recommended to improve VIV performances in twin parallel bridges.
基金supported by the National Natural Science Foundation of China(Grant No.12102131).
文摘Legendre polynomial method is well-known in modeling acoustic wave characteristics.This method uses for the mechanical displacements a single polynomial expansion over the entire sandwich layers.This results in a limitation in the accuracy of the field profile restitution.Thus,it can deal with the guided waves in layered sandwich only when the material properties of adjacent layers do not change significantly.Despite the great efforts regarding this issue in the literature,there remain open questions.One of them is:“what is the exact threshold of contrasting material properties of adjacent layers for which this polynomial method cannot correctly restitute the roots of guided waves?”We investigated this numerical issue using the calculated guided phase velocities in 0°/φ/0°-carbon fibre reinforced plastics(CFRP)sandwich plates with gradually increasing angleφ.Then,we approached this numerical problem by varying the middle layer thickness h90°for the 0°/90°/0°-CFRP sandwich structure,and we proposed an exact thickness threshold of the middle layer for the Legendre polynomial method limitations.We showed that the polynomial method fails to calculate the quasi-symmetric Lamb mode in 0°/φ/0°-CFRP whenφ>25°.Moreover,we introduced a new Lamb mode so-called minimum-group-velocity that has never been addressed in literature.
