A design idea for single-component metamaterial plates is proposed to achieve the thermal stability of flexural wave bandgap by the perforated and pre-curved patterns.The band structure analysis suggests that perforat...A design idea for single-component metamaterial plates is proposed to achieve the thermal stability of flexural wave bandgap by the perforated and pre-curved patterns.The band structure analysis suggests that perforation can release part of the in-plane thermal expansion to weaken the softening effect of thermal stress.Introducing precurved components to the perforated structure will stop the decrement of the bandgap frequency in thermal environment,and even make the frequency higher with appropriate structural parameters.The bending stiffness of the heated plate is enhanced by the thermal deflection induced stiffening effect of the pre-curved components.The segmented pre-curved component presents a strong ability to resist the thermal influence on the flexural wave bandgap.A simplified model is established for the local structure of the precurved component.The theoretical calculations explain the thermally induced frequency increment of the bandgap and the discrepancy in the thermal response between the two pre-curved models.The transmittance of flexural wave validates the effectiveness of the proposed design.展开更多
Ceramic thin plates were prepared using kaolin,potassium sodium feldspar and quartz powder as the main raw materials and kaolin,α-Al_(2)O_(3),MoO_(3) and AlF_(3)·3H_(2)O as additives.The experiment examined the ...Ceramic thin plates were prepared using kaolin,potassium sodium feldspar and quartz powder as the main raw materials and kaolin,α-Al_(2)O_(3),MoO_(3) and AlF_(3)·3H_(2)O as additives.The experiment examined the effects of different additives on mullite formation,as well as the microstructure and properties of the ceramic thin plates.Additionally,the study explored the toughening and strengthening mechanisms induced by the additives,providing a theoretical foundation for further optimizing the toughness of ceramic thin plates.The results showed that the D4 sample fired at 1220℃(with an addition of 20 wt% α-Al_(2)O_(3))exhibited the best performance,with a water absorption rate of 0.07%,apparent porosity of 0.18%,bulk density of 2.75 g·cm^(-3),firing shrinkage of 12.76%,bending strength reaching 101.93 MPa,and fracture toughness of 2.51 MPa·m^(1/2).As the amount ofα-Al_(2)O_(3) additive increased,the ceramic thin plates exhibited a greater abundance of short rod-like mullite and corundum grains,which were tightly packed together,forming a framework for the ceramic thin plates.This microstructure enhanced pathways for crack propagation,dispersed internal stresses,and increased fracture surface energy,resulting in significant improvements in both strength and fracture toughness of the ceramic thin plates.展开更多
This paper aims to explore and quantify the nonlinear vibration response of tri-directional functionally graded sandwich(3D-FGSW)plates partially supported by a Pasternak foundation(PF)subjected to blast loading(BL).A...This paper aims to explore and quantify the nonlinear vibration response of tri-directional functionally graded sandwich(3D-FGSW)plates partially supported by a Pasternak foundation(PF)subjected to blast loading(BL).A key objective is to develop a computationally efficient finite element framework capable of accurately capturing the complex behavior of 3D-FGSW plates.The studied configuration features a two-dimensional functionally graded material(2D-FGM)core between two threedimensional functionally graded material(3D-FGM)face layers.Nonlinear geometric effects,including mid-plane stretching,are modeled using von K arm an-type assumptions,and the governing equations are formulated via Hamilton's principle within an improved first-order shear deformation theory(iFSDT).The accuracy and computational efficiency of the proposed method are validated through comparison with existing benchmark solutions.Subsequently,a comprehensive parametric study is carried out to examine the effects of geometric dimensions,material properties,foundation sizes,and boundary conditions(BCs)on the nonlinear vibration of 3D-FGSW plates.The findings of this work are expected to provide valuable insights for the design and manufacturing of advanced sandwich structures subjected to BL.展开更多
A 32-channel charge-sensitive amplifier(CSA)is designed for fast timing in the delay-line readout of a parallel plate avalanche counter(PPAC)array.It is realized on a PCB with operational amplifiers and other discrete...A 32-channel charge-sensitive amplifier(CSA)is designed for fast timing in the delay-line readout of a parallel plate avalanche counter(PPAC)array.It is realized on a PCB with operational amplifiers and other discrete components.Each channel consists of an integrator,a pole-zero cancellation net,and a linear amplification stage,which can be adapted to accommodate either positive or negative input signals.The RMS equivalent input noise charges are 3.3 fC,the conversion gains are approximately±2 mV∕fC,and the intrinsic time resolution reaches 32 ps.In the prototype PPAC application,the CSA performs as well as the commercial FTA820A amplifier,providing a position resolution as good as 0.17 mm,and exhibiting reliable stability during several hours of continuous data acquisition.展开更多
In this paper,a theoretical model is established for locally resonant plates with general resonators,and the corresponding governing equation is derived.The model provides a mathematical demonstration of the locally r...In this paper,a theoretical model is established for locally resonant plates with general resonators,and the corresponding governing equation is derived.The model provides a mathematical demonstration of the locally resonant effect,which contains two parts:the first part is induced by translation coupling,and the second part is induced by rotation coupling.The second part cannot be reflected by most existing theoretical models.The analytical solutions of the dynamic response are compared with the direct numerical simulation(DNS)results for two locally resonant plates with different resonator types,thereby validating the general applicability of the present model.The rotation coupling effect leads to the frequency-dependent effective rotational inertia density and anisotropic dispersion relation of the locally resonant plate,as well as the enhancement of the structural vibration suppression ability.展开更多
A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The resu...A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The results show that cold-pressing produces intense plastic deformation near the corrugated surface of the Al plate,which promotes dynamic recrystallization of the Al substrate near the interface during the subsequent hot-pressing.In addition,the initial corrugation on the surface of the Al plate also changes the local stress state near the interface during hot pressing,which has a large effect on the texture components of the substrates near the corrugated interface.The construction of the corrugated interface can greatly enhance the shear strength by 2−4 times due to the increased contact area and the strong“mechanical gearing”effect.Moreover,the mechanical properties are largely depended on the orientation relationship between corrugated direction and loading direction.展开更多
In this paper,we define for the trace operator,the solution of certain models of vibrating plates standards with initial data in a strategic region spaces of weak regularities.Indeed,we know that the notion of regiona...In this paper,we define for the trace operator,the solution of certain models of vibrating plates standards with initial data in a strategic region spaces of weak regularities.Indeed,we know that the notion of regional controllability is more adapted to systems described by dynamic systems.Regional controllability results in a strategic area were established for vibrating plates by the Hilbertian Uniqueness Method.展开更多
Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The t...Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The traditional thermal elastic-plastic finite element method(TEP-FEM)can accurately predict welding deformation.However,its efficiency is low because of the complex nonlinear transient computation,making it difficult to meet the needs of rapid engineering evaluation.To address this challenge,this study proposes an efficient prediction method for welding deformation in marine thin plate butt welds.This method is based on the coupled temperature gradient-thermal strain method(TG-TSM)that integrates inherent strain theory with a shell element finite element model.The proposed method first extracts the distribution pattern and characteristic value of welding-induced inherent strain through TEP-FEM analysis.This strain is then converted into the equivalent thermal load applied to the shell element model for rapid computation.The proposed method-particularly,the gradual temperature gradient-thermal strain method(GTG-TSM)-achieved improved computational efficiency and consistent precision.Furthermore,the proposed method required much less computation time than the traditional TEP-FEM.Thus,this study lays the foundation for future prediction of welding deformation in more complex marine thin plates.展开更多
High-Mg andesites(HMAs)typically originate in subduction-related tectonic settings,including active continental margins and island arcs,and studies of HMAs can constrain the tectonic evolution of the South China Block...High-Mg andesites(HMAs)typically originate in subduction-related tectonic settings,including active continental margins and island arcs,and studies of HMAs can constrain the tectonic evolution of the South China Block and Paleo-Tethyan Ocean.This paper presents new chronological and geochemical data for high-Mg gabbroic diorites in the Funing area,southern South China.The gabbroic diorites yield ages of 254-249 Ma,and have moderate SiO2 contents(51.3%-57.8%),high MgO contents(4.6%-10.2%)and Mg^(#)values(52-75),enrichment in large-ion lithophile elements and light rare earth elements,and depletion in high-field-strength elements-collectively displaying geochemical signatures typical of sanukites.The gabbroic diorites have radiogenic initial Sr and Pb isotopic compositions,and negativeεNd(t)andεHf(t)values.These characteristics distinguish the Funing gabbroic diorites from subduction-related igneous rocks in the Paleo-Pacific tectonic domain.Instead,they are isotopically similar to HMAs and basalts along the Paleo-Tethys suture.We propose the high-Mg gabbroic diorites and basaltic andesites in Funing area share a common mantle source,linked to subduction and rollback of the Paleo-Tethyan plate beneath the South China Block,which triggered back-arc rifting and partial melting of the metasomatized lithospheric mantle during the Late Permian to Early Triassic.展开更多
The transformation of the dissimilar metals in the welding area into a single metal is an important method for achieving high-quality welded connection in the dissimilar metal laminated composite plate.In this study,a...The transformation of the dissimilar metals in the welding area into a single metal is an important method for achieving high-quality welded connection in the dissimilar metal laminated composite plate.In this study,a high-performance titanium/steel composite plate(TSCP)with pure titaniumization in the welding area was prepared by cold spraying,hot rolling and heat treatment processes.The results indicate that cold spraying achieves effective pre-composite deposition of titanium particles while inhibiting interfacial oxidation and Fe-Ti alloying reactions,producing a relatively dense pure titanium coating with a low porosity of only 1.2%.Hot rolling eliminates internal defects and promotes strong metallurgical bonding of the composite interface.The heat treatment promotes the recrystallization and reduces the dislocation density within the coating.The interfacial bonding strength of the welding area with pure titaniumization of TSCP is 257 MPa,and the tensile strength of that is 414 MPa,reaching 95.6%of the TSCP’s base material.展开更多
We investigate the effects of projectile material on high-speed penetration/perforation of Inconel 718 alloy(IN718)plates.High-speed ballistic impact tests are conducted on 2 mm-thickness IN718 plates with 5-mm-diamet...We investigate the effects of projectile material on high-speed penetration/perforation of Inconel 718 alloy(IN718)plates.High-speed ballistic impact tests are conducted on 2 mm-thickness IN718 plates with 5-mm-diameter stainless steel 304(SS304),Ti alloy TC4,and Al alloy AA1060 spherical projectiles.The impact processes are captured with high-speed photography.Optical and scanning electron microscopy and laser scan are conducted on recovered projectiles and targets.Finite element models of the ballistic impact are established based on the coupled Eulerian-Lagrangian algorithm with the Johnson-Cook constitutive model and failure criterion,and can well reproduce the experimental results.The experimental and simulated data related to projectile dynamics,and the geometries of postmortem projectiles and bullet holes are analyzed with phenomenological models.Projectile velocity evolution can be described with hydrodynamic models of penetration.Dimensional analysis reveals a universal relationship between the bullet hole expansion coefficient and the normalized dynamic pressure,regardless of the projectile material.However,the projectile material does affect projectile deformation,bullet hole size,and energy absorption of target.展开更多
In order to investigate the penetration performance of Linear-Shaped Charge(LSC),Embowed LinearShaped Charge(ELSC),and Embowed Linear Explosively Formed Projectile(ELEFP)on T-shaped stiffened plates,a series of near-f...In order to investigate the penetration performance of Linear-Shaped Charge(LSC),Embowed LinearShaped Charge(ELSC),and Embowed Linear Explosively Formed Projectile(ELEFP)on T-shaped stiffened plates,a series of near-field air-burst experiments are conducted.The damage modes and characteristics of the target plates are compared and analyzed.Each flat plate section is completely punctured,resulting in a penetration hole.The damage modes induced by the three charge types on the stiffened plate structure are consistent,characterized by shear failure in the central region of the flat plate due to penetration by the penetrator,localized plastic deformation of the flat plate,and local penetration failure resulting from partial perforation of the central stiffener.The penetration lengths caused by ELSC and ELEFP are 45.1%and 46.1% larger than that of LSC,while the half-width of the penetration hole generated by ELEFP is 54.2% and 24.7% smaller than that of ELSC and LSC,respectively.The penetration height caused by ELEFP are 17.5%and 62.1% larger than that of ELSC and LSC,respectively.The stiffener effectively segments the damage area,enhancing the local structural strength and limiting the extent of plastic deformation in the flat plate section.The comparative results show that the ELSC proves to be more effective for efficient large-scale damage,and ELEFP is more suitable for achieving efficient localized damage.展开更多
In this paper,the free vibration and stationary stochastic response of functionally graded(FG)rectangular plates with varying thickness in supersonic flow and thermal environment are analyzed.Two types of material pro...In this paper,the free vibration and stationary stochastic response of functionally graded(FG)rectangular plates with varying thickness in supersonic flow and thermal environment are analyzed.Two types of material property variations of FG plates with varying thickness are considered:the variation along the direction perpendicular to the mid-surface and that along the direction perpendicular to the bottom surface.Considering the effects of aerodynamic pressure and thermal load,the governing equations of motion of FG plates with varying thickness are derived using Hamilton’s principle within the framework of first-order shear deformation theory.A meshfree Jacobi radial point interpolation(Jacobi-RPI)shape function is constructed by combining the Jacobi polynomials and radial basis to approximate the displacement components of the plate.The accuracy and reliability of the present approach are confirmed through sufficient comparisons with numerical results from the published literature and the finite element software ABAQUS.Finally,the effects of different parameters on the free vibration and stationary stochastic response of FG plates are investigated.展开更多
A high-order hybrid numerical framework is developed by coupling a three-stage exponential time integrator with a Runge–Kutta scheme for the efficient solution of partial differential equations involving first-order ...A high-order hybrid numerical framework is developed by coupling a three-stage exponential time integrator with a Runge–Kutta scheme for the efficient solution of partial differential equations involving first-order time derivatives.The proposed scheme attains third-order temporal accuracy and is rigorously validated through stability and convergence analyses for both scalar and coupled systems.Its effectiveness is demonstrated by simulating unsteady Eyring-Prandtl non-Newtonian nanofluid flow over a Riga plate with coupled heat and mass transfer under electromagnetic actuation.The physical model accounts for Brownian motion and thermophoresis,and the nanofluid considered is a Prandtl-type non-Newtonian base fluid containing suspended nanoparticles,with heat and mass transport governed by coupled momentum,energy,and concentration equations.Numerical simulations are performed over practically relevant parameter ranges,with the Reynolds number fixed at Re=5 and the Prandtl number set to Pr=3 to represent moderate inertial and thermal diffusion effects typical of nanofluid transport systems.To enhance computational efficiency,an artificial neural network(ANN)-based surrogate model is developed to predict the skin friction coefficient and local Sherwood number as functions of Reynolds number,Prandtl number,Schmidt number,Brownian motion,and thermophoresis parameters.The training dataset is generated entirely from high-fidelity numerical simulations produced by the proposed hybrid scheme.The data are systematically partitioned into 70%for training,15%for validation,and 15%for testing,ensuring reliable generalization.Regression analysis yields a near-unity correlation coefficient(R≈0.99),while error histograms exhibit tightly clustered residuals around zero,confirming high predictive accuracy.Furthermore,a benchmark convergence study using Stokes’first problem demonstrates that the proposed scheme consistently achieves lower global error norms than the classical Runge–Kutta method for identical spatial and temporal resolutions.Overall,this study introduces a novel computational intelligence framework that integrates high-order numerical solvers with machine learning,offering a robust and time-efficient tool for advanced modeling and real-time prediction of non-Newtonian nanofluid transport phenomena under electromagnetic flow control.展开更多
With the continuous increase in performance requirements for power systems in the aerospace and low-altitude economy sectors,designing lightweight and highstrength blade structures with excellent dynamic characteristi...With the continuous increase in performance requirements for power systems in the aerospace and low-altitude economy sectors,designing lightweight and highstrength blade structures with excellent dynamic characteristics has become critical.This paper puts forward a dynamic model for a rotating functionally graded graphenereinforced(FG-GPR)sandwich metal porous cantilever pre-twisted plate(PTP),aiming to analyze its natural vibration characteristics.To this end,the mixture principle and the revised Halpin-Tsai model are used to determine the parameters of graphene and porosity distributions in the core layer.With the classical plate theory,the Rayleigh-Ritz method,and the polynomials,the dynamic equations are derived to solve for the free vibration mode shapes and frequencies of the rotating FG-GPR sandwich metal porous cantilever PTP.The comparison of natural frequencies and mode shapes with available literature results confirms the precision of the theoretical formulation and numerical computations.The bending stiffnesses are analyzed.Finally,the effects of different graphene/pore distributions,length-to-thickness/width ratios,layer thickness ratios,twist angles,and rotational speeds on the natural frequencies of the system are systematically investigated.展开更多
Functionally graded material(FGM)plates are widely used in various engineering structures owing to their tailor-made mechanical properties,whereas cracked homogeneous plates constitute a canonical setting in fracture ...Functionally graded material(FGM)plates are widely used in various engineering structures owing to their tailor-made mechanical properties,whereas cracked homogeneous plates constitute a canonical setting in fracture mechanics analysis.These two classes of problems respectively embody material non-uniformity and geometric discontinuity,thereby imposing more stringent requirements on numerical methods in terms of high-order field continuity and accurate defect representation.Based on the classical Kirchhoff-Love plate theory,a numerical manifold method(MLS-NMM)incorporating moving least squares(MLS)interpolation is developed for bending analysis of FGM plates and fracture simulation of homogeneous plates with defects.The method constructs an H^(2)-regular approximation with high-order continuous weighting functions and,combined with the separation of mathematical and physical covers,establishes a unified framework that accurately handles material gradients and cracks without mesh reconstruction.For the crack tip,a singular physical cover incorporating the Williams asymptotic field is introduced to achieve local enrichment,enabling the natural capture of displacement discontinuity and stress singularity.Stress intensity factors are extracted using the interaction integral method,and the dimensionless J-integral shows a maximum relative error below 1.2%compared with the reference solution.Numerical results indicate that MLS-NMM exhibits excellent convergence performance:using 676 mathematical nodes,the nondimensional central deflection of both FGM and homogeneous plates agrees with reference solutions with a maximum relative error below 0.81%,and no shear locking occurs.A systematic analysis reveals that for a simply supported on all four edges(SSSS)FGM square plate with a/h=10,the nondimensional central deflection increases by 212%as the gradient index nrises from 0 to 5.For a homogeneous plate containing a central crack with c/a=0.6,the nondimensional central deflection increases by approximately 46%compared with the intact plate.Under weak boundary constraints(e.g.,SFSF),the deformation is markedly amplified,with the deflection reaching more than three times that under strong constraints(SCSC).The proposed method provides an efficient,reconstruction-free numerical tool for high-accuracy bending and fracture analyses of FGM and cracked thin-plate structures.展开更多
Objective: To investigate the therapeutic advantages of closed reduction and Kirschner wire fixation versus open reduction and plate fixation in patients with hand surgery fractures. Methods: The sample was collected ...Objective: To investigate the therapeutic advantages of closed reduction and Kirschner wire fixation versus open reduction and plate fixation in patients with hand surgery fractures. Methods: The sample was collected from May 2021 to May 2025, consisting of 80 patients with hand surgery fractures. These patients were randomly divided into two groups using the red and blue ball method: the plate fixation group (40 cases, treated with open reduction and plate fixation) and the Kirschner wire fixation group (40 cases, treated with closed reduction and Kirschner wire fixation). The therapeutic effects between the two groups were randomly compared. Results: The Kirschner wire fixation group outperformed the plate fixation group in all indicators except for hand function scores (p < 0.05). There was no statistically significant difference in hand function scores between the two groups (p > 0.05). Conclusion: Compared with open reduction and plate fixation, closed reduction and Kirschner wire fixation for patients with hand surgery fractures achieves a more pronounced therapeutic effect, with advantages such as less trauma, shorter operation time, less bleeding, and a lower incidence of complications. It is suitable for hand surgery fractures with good stability. Open reduction and plate internal fixation have greater advantages in complex fractures and cases requiring high stability, and are worthy of promotion and application.展开更多
Titanium plates with a Ti−O solid solution surface-hardened layer were cold roll-bonded with 304 stainless steel plates with high work hardening rates.The evolution and mechanisms affecting the interfacial bonding str...Titanium plates with a Ti−O solid solution surface-hardened layer were cold roll-bonded with 304 stainless steel plates with high work hardening rates.The evolution and mechanisms affecting the interfacial bonding strength in titanium/stainless steel laminated composites were investigated.Results indicate that the hardened layer reduces the interfacial bonding strength from over 261 MPa to less than 204 MPa.During the cold roll-bonding process,the hardened layer fractures,leading to the formation of multi-scale cracks that are difficult for the stainless steel to fill.This not only hinders the development of an interlocking interface but also leads to the presence of numerous microcracks and hardened blocks along the nearly straight interface,consequently weakening the interfacial bonding strength.In metals with high work hardening rates,the conventional approach of enhancing interface interlocking and improving interfacial bonding strength by using a surface-hardened layer becomes less effective.展开更多
On January 7,2025,01:05:15 UTC(9:05 a.m.local time)southern Tibet was rocked by a M_(W)7.1 earthquake(M_(W)=moment magnitude,USGS)centered(28.639°N 87.361°E)in the Lhasa Block north of the India/Eurasia Plat...On January 7,2025,01:05:15 UTC(9:05 a.m.local time)southern Tibet was rocked by a M_(W)7.1 earthquake(M_(W)=moment magnitude,USGS)centered(28.639°N 87.361°E)in the Lhasa Block north of the India/Eurasia Plate boundary,in a remote area about 180 km SW of Xigaze,in Dingri County of Shigatse of the Xizang Autonomous Region(Figure 1).展开更多
On February 8,2025,a remote area in the Caribbean Sea was rocked by a large M_(W)7.6(USGS,2025) earthquake,centered 209 km SSW of Georgetown,the capital of the Cayman Islands,and the largest city(population~41 000) of...On February 8,2025,a remote area in the Caribbean Sea was rocked by a large M_(W)7.6(USGS,2025) earthquake,centered 209 km SSW of Georgetown,the capital of the Cayman Islands,and the largest city(population~41 000) of the British Overseas Territories(Figure 1).The earthquake was significant due to its large magnitude,potential regional impact,and the possibility of generating a tsunami.展开更多
基金Project supported by the National Natural Science Foundation of China(Nos.12102321 and 52192633)the Natural Science Basic Research Plan in Shaanxi Province of China(No.2025JCYBMS-050)。
文摘A design idea for single-component metamaterial plates is proposed to achieve the thermal stability of flexural wave bandgap by the perforated and pre-curved patterns.The band structure analysis suggests that perforation can release part of the in-plane thermal expansion to weaken the softening effect of thermal stress.Introducing precurved components to the perforated structure will stop the decrement of the bandgap frequency in thermal environment,and even make the frequency higher with appropriate structural parameters.The bending stiffness of the heated plate is enhanced by the thermal deflection induced stiffening effect of the pre-curved components.The segmented pre-curved component presents a strong ability to resist the thermal influence on the flexural wave bandgap.A simplified model is established for the local structure of the precurved component.The theoretical calculations explain the thermally induced frequency increment of the bandgap and the discrepancy in the thermal response between the two pre-curved models.The transmittance of flexural wave validates the effectiveness of the proposed design.
基金Funded by the National Key Technology Research and Development Program of the Ministry of Science and Technology of China(No.2023YFB4204302)。
文摘Ceramic thin plates were prepared using kaolin,potassium sodium feldspar and quartz powder as the main raw materials and kaolin,α-Al_(2)O_(3),MoO_(3) and AlF_(3)·3H_(2)O as additives.The experiment examined the effects of different additives on mullite formation,as well as the microstructure and properties of the ceramic thin plates.Additionally,the study explored the toughening and strengthening mechanisms induced by the additives,providing a theoretical foundation for further optimizing the toughness of ceramic thin plates.The results showed that the D4 sample fired at 1220℃(with an addition of 20 wt% α-Al_(2)O_(3))exhibited the best performance,with a water absorption rate of 0.07%,apparent porosity of 0.18%,bulk density of 2.75 g·cm^(-3),firing shrinkage of 12.76%,bending strength reaching 101.93 MPa,and fracture toughness of 2.51 MPa·m^(1/2).As the amount ofα-Al_(2)O_(3) additive increased,the ceramic thin plates exhibited a greater abundance of short rod-like mullite and corundum grains,which were tightly packed together,forming a framework for the ceramic thin plates.This microstructure enhanced pathways for crack propagation,dispersed internal stresses,and increased fracture surface energy,resulting in significant improvements in both strength and fracture toughness of the ceramic thin plates.
文摘This paper aims to explore and quantify the nonlinear vibration response of tri-directional functionally graded sandwich(3D-FGSW)plates partially supported by a Pasternak foundation(PF)subjected to blast loading(BL).A key objective is to develop a computationally efficient finite element framework capable of accurately capturing the complex behavior of 3D-FGSW plates.The studied configuration features a two-dimensional functionally graded material(2D-FGM)core between two threedimensional functionally graded material(3D-FGM)face layers.Nonlinear geometric effects,including mid-plane stretching,are modeled using von K arm an-type assumptions,and the governing equations are formulated via Hamilton's principle within an improved first-order shear deformation theory(iFSDT).The accuracy and computational efficiency of the proposed method are validated through comparison with existing benchmark solutions.Subsequently,a comprehensive parametric study is carried out to examine the effects of geometric dimensions,material properties,foundation sizes,and boundary conditions(BCs)on the nonlinear vibration of 3D-FGSW plates.The findings of this work are expected to provide valuable insights for the design and manufacturing of advanced sandwich structures subjected to BL.
基金supported by the National Natural Science Foundation of China(Nos.U2167202,12225504,12005276)the Natural Science Foundation of Shandong Province(No.ZR2024QA172)the Fundamental Research Funds of Shandong University.
文摘A 32-channel charge-sensitive amplifier(CSA)is designed for fast timing in the delay-line readout of a parallel plate avalanche counter(PPAC)array.It is realized on a PCB with operational amplifiers and other discrete components.Each channel consists of an integrator,a pole-zero cancellation net,and a linear amplification stage,which can be adapted to accommodate either positive or negative input signals.The RMS equivalent input noise charges are 3.3 fC,the conversion gains are approximately±2 mV∕fC,and the intrinsic time resolution reaches 32 ps.In the prototype PPAC application,the CSA performs as well as the commercial FTA820A amplifier,providing a position resolution as good as 0.17 mm,and exhibiting reliable stability during several hours of continuous data acquisition.
基金Project supported by the National Natural Science Foundation of China(No.12472062)。
文摘In this paper,a theoretical model is established for locally resonant plates with general resonators,and the corresponding governing equation is derived.The model provides a mathematical demonstration of the locally resonant effect,which contains two parts:the first part is induced by translation coupling,and the second part is induced by rotation coupling.The second part cannot be reflected by most existing theoretical models.The analytical solutions of the dynamic response are compared with the direct numerical simulation(DNS)results for two locally resonant plates with different resonator types,thereby validating the general applicability of the present model.The rotation coupling effect leads to the frequency-dependent effective rotational inertia density and anisotropic dispersion relation of the locally resonant plate,as well as the enhancement of the structural vibration suppression ability.
基金supported by Guangdong Major Project of Basic and Applied Basic Research, China (No. 2020B0301030006)Fundamental Research Funds for the Central Universities, China (No. SWU-XDJH202313)+1 种基金Chongqing Postdoctoral Science Foundation Funded Project, China (No. 2112012728014435)the Chongqing Postgraduate Research and Innovation Project, China (No. CYS23197)。
文摘A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The results show that cold-pressing produces intense plastic deformation near the corrugated surface of the Al plate,which promotes dynamic recrystallization of the Al substrate near the interface during the subsequent hot-pressing.In addition,the initial corrugation on the surface of the Al plate also changes the local stress state near the interface during hot pressing,which has a large effect on the texture components of the substrates near the corrugated interface.The construction of the corrugated interface can greatly enhance the shear strength by 2−4 times due to the increased contact area and the strong“mechanical gearing”effect.Moreover,the mechanical properties are largely depended on the orientation relationship between corrugated direction and loading direction.
文摘In this paper,we define for the trace operator,the solution of certain models of vibrating plates standards with initial data in a strategic region spaces of weak regularities.Indeed,we know that the notion of regional controllability is more adapted to systems described by dynamic systems.Regional controllability results in a strategic area were established for vibrating plates by the Hilbertian Uniqueness Method.
基金Supported by the National Natural Science Foundation of China under Grant No.51975138the High-Tech Ship Scientific Research Project from the Ministry of Industry and Information Technology under Grant No.CJ05N20the National Defense Basic Research Project under Grant No.JCKY2023604C006.
文摘Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The traditional thermal elastic-plastic finite element method(TEP-FEM)can accurately predict welding deformation.However,its efficiency is low because of the complex nonlinear transient computation,making it difficult to meet the needs of rapid engineering evaluation.To address this challenge,this study proposes an efficient prediction method for welding deformation in marine thin plate butt welds.This method is based on the coupled temperature gradient-thermal strain method(TG-TSM)that integrates inherent strain theory with a shell element finite element model.The proposed method first extracts the distribution pattern and characteristic value of welding-induced inherent strain through TEP-FEM analysis.This strain is then converted into the equivalent thermal load applied to the shell element model for rapid computation.The proposed method-particularly,the gradual temperature gradient-thermal strain method(GTG-TSM)-achieved improved computational efficiency and consistent precision.Furthermore,the proposed method required much less computation time than the traditional TEP-FEM.Thus,this study lays the foundation for future prediction of welding deformation in more complex marine thin plates.
基金supported by the National Natural Science Foundation of China (42473063)Guike AD24010023, the Seventh Guangxi Zhuang Autonomous Region Bagui Scholars Program (to LIU Xijun)the Guangxi Natural Science Foundations of China (2025GXNSFBA069054)
文摘High-Mg andesites(HMAs)typically originate in subduction-related tectonic settings,including active continental margins and island arcs,and studies of HMAs can constrain the tectonic evolution of the South China Block and Paleo-Tethyan Ocean.This paper presents new chronological and geochemical data for high-Mg gabbroic diorites in the Funing area,southern South China.The gabbroic diorites yield ages of 254-249 Ma,and have moderate SiO2 contents(51.3%-57.8%),high MgO contents(4.6%-10.2%)and Mg^(#)values(52-75),enrichment in large-ion lithophile elements and light rare earth elements,and depletion in high-field-strength elements-collectively displaying geochemical signatures typical of sanukites.The gabbroic diorites have radiogenic initial Sr and Pb isotopic compositions,and negativeεNd(t)andεHf(t)values.These characteristics distinguish the Funing gabbroic diorites from subduction-related igneous rocks in the Paleo-Pacific tectonic domain.Instead,they are isotopically similar to HMAs and basalts along the Paleo-Tethys suture.We propose the high-Mg gabbroic diorites and basaltic andesites in Funing area share a common mantle source,linked to subduction and rollback of the Paleo-Tethyan plate beneath the South China Block,which triggered back-arc rifting and partial melting of the metasomatized lithospheric mantle during the Late Permian to Early Triassic.
基金financially supported by the National Key R&D Program of China(No.2018YFA0707300)the National Natural Science Foundation of China(No.52374376)。
文摘The transformation of the dissimilar metals in the welding area into a single metal is an important method for achieving high-quality welded connection in the dissimilar metal laminated composite plate.In this study,a high-performance titanium/steel composite plate(TSCP)with pure titaniumization in the welding area was prepared by cold spraying,hot rolling and heat treatment processes.The results indicate that cold spraying achieves effective pre-composite deposition of titanium particles while inhibiting interfacial oxidation and Fe-Ti alloying reactions,producing a relatively dense pure titanium coating with a low porosity of only 1.2%.Hot rolling eliminates internal defects and promotes strong metallurgical bonding of the composite interface.The heat treatment promotes the recrystallization and reduces the dislocation density within the coating.The interfacial bonding strength of the welding area with pure titaniumization of TSCP is 257 MPa,and the tensile strength of that is 414 MPa,reaching 95.6%of the TSCP’s base material.
基金supported by National Natural Science Foundation of China(No.12402465)Sichuan Science and Technology Program(No.2023NSFSC1284)。
文摘We investigate the effects of projectile material on high-speed penetration/perforation of Inconel 718 alloy(IN718)plates.High-speed ballistic impact tests are conducted on 2 mm-thickness IN718 plates with 5-mm-diameter stainless steel 304(SS304),Ti alloy TC4,and Al alloy AA1060 spherical projectiles.The impact processes are captured with high-speed photography.Optical and scanning electron microscopy and laser scan are conducted on recovered projectiles and targets.Finite element models of the ballistic impact are established based on the coupled Eulerian-Lagrangian algorithm with the Johnson-Cook constitutive model and failure criterion,and can well reproduce the experimental results.The experimental and simulated data related to projectile dynamics,and the geometries of postmortem projectiles and bullet holes are analyzed with phenomenological models.Projectile velocity evolution can be described with hydrodynamic models of penetration.Dimensional analysis reveals a universal relationship between the bullet hole expansion coefficient and the normalized dynamic pressure,regardless of the projectile material.However,the projectile material does affect projectile deformation,bullet hole size,and energy absorption of target.
基金supported by the National Natural Science Foundation of China(Grant Nos.52271307,52061135107,52192692,11802025)the Liao Ning Excellent Youth Fund Program(Grant No.2023JH3/10200012)+1 种基金the Liao Ning Revitalization Tal-ents Program(Grant No.XLYC1908027)the Fundamental Research Funds for the Central Universities(Grant Nos.DUT20RC(3)025,DUT20TD108,DUT20LAB308)。
文摘In order to investigate the penetration performance of Linear-Shaped Charge(LSC),Embowed LinearShaped Charge(ELSC),and Embowed Linear Explosively Formed Projectile(ELEFP)on T-shaped stiffened plates,a series of near-field air-burst experiments are conducted.The damage modes and characteristics of the target plates are compared and analyzed.Each flat plate section is completely punctured,resulting in a penetration hole.The damage modes induced by the three charge types on the stiffened plate structure are consistent,characterized by shear failure in the central region of the flat plate due to penetration by the penetrator,localized plastic deformation of the flat plate,and local penetration failure resulting from partial perforation of the central stiffener.The penetration lengths caused by ELSC and ELEFP are 45.1%and 46.1% larger than that of LSC,while the half-width of the penetration hole generated by ELEFP is 54.2% and 24.7% smaller than that of ELSC and LSC,respectively.The penetration height caused by ELEFP are 17.5%and 62.1% larger than that of ELSC and LSC,respectively.The stiffener effectively segments the damage area,enhancing the local structural strength and limiting the extent of plastic deformation in the flat plate section.The comparative results show that the ELSC proves to be more effective for efficient large-scale damage,and ELEFP is more suitable for achieving efficient localized damage.
文摘In this paper,the free vibration and stationary stochastic response of functionally graded(FG)rectangular plates with varying thickness in supersonic flow and thermal environment are analyzed.Two types of material property variations of FG plates with varying thickness are considered:the variation along the direction perpendicular to the mid-surface and that along the direction perpendicular to the bottom surface.Considering the effects of aerodynamic pressure and thermal load,the governing equations of motion of FG plates with varying thickness are derived using Hamilton’s principle within the framework of first-order shear deformation theory.A meshfree Jacobi radial point interpolation(Jacobi-RPI)shape function is constructed by combining the Jacobi polynomials and radial basis to approximate the displacement components of the plate.The accuracy and reliability of the present approach are confirmed through sufficient comparisons with numerical results from the published literature and the finite element software ABAQUS.Finally,the effects of different parameters on the free vibration and stationary stochastic response of FG plates are investigated.
基金supported and funded by the Deanship of Scientific Research at Imam Mohammad Ibn Saud Islamic University(IMSIU)(grant number IMSIU-DDRSP2603).
文摘A high-order hybrid numerical framework is developed by coupling a three-stage exponential time integrator with a Runge–Kutta scheme for the efficient solution of partial differential equations involving first-order time derivatives.The proposed scheme attains third-order temporal accuracy and is rigorously validated through stability and convergence analyses for both scalar and coupled systems.Its effectiveness is demonstrated by simulating unsteady Eyring-Prandtl non-Newtonian nanofluid flow over a Riga plate with coupled heat and mass transfer under electromagnetic actuation.The physical model accounts for Brownian motion and thermophoresis,and the nanofluid considered is a Prandtl-type non-Newtonian base fluid containing suspended nanoparticles,with heat and mass transport governed by coupled momentum,energy,and concentration equations.Numerical simulations are performed over practically relevant parameter ranges,with the Reynolds number fixed at Re=5 and the Prandtl number set to Pr=3 to represent moderate inertial and thermal diffusion effects typical of nanofluid transport systems.To enhance computational efficiency,an artificial neural network(ANN)-based surrogate model is developed to predict the skin friction coefficient and local Sherwood number as functions of Reynolds number,Prandtl number,Schmidt number,Brownian motion,and thermophoresis parameters.The training dataset is generated entirely from high-fidelity numerical simulations produced by the proposed hybrid scheme.The data are systematically partitioned into 70%for training,15%for validation,and 15%for testing,ensuring reliable generalization.Regression analysis yields a near-unity correlation coefficient(R≈0.99),while error histograms exhibit tightly clustered residuals around zero,confirming high predictive accuracy.Furthermore,a benchmark convergence study using Stokes’first problem demonstrates that the proposed scheme consistently achieves lower global error norms than the classical Runge–Kutta method for identical spatial and temporal resolutions.Overall,this study introduces a novel computational intelligence framework that integrates high-order numerical solvers with machine learning,offering a robust and time-efficient tool for advanced modeling and real-time prediction of non-Newtonian nanofluid transport phenomena under electromagnetic flow control.
基金Project supported by the National Natural Science Foundation of China(Nos.12272056 and 11832002)。
文摘With the continuous increase in performance requirements for power systems in the aerospace and low-altitude economy sectors,designing lightweight and highstrength blade structures with excellent dynamic characteristics has become critical.This paper puts forward a dynamic model for a rotating functionally graded graphenereinforced(FG-GPR)sandwich metal porous cantilever pre-twisted plate(PTP),aiming to analyze its natural vibration characteristics.To this end,the mixture principle and the revised Halpin-Tsai model are used to determine the parameters of graphene and porosity distributions in the core layer.With the classical plate theory,the Rayleigh-Ritz method,and the polynomials,the dynamic equations are derived to solve for the free vibration mode shapes and frequencies of the rotating FG-GPR sandwich metal porous cantilever PTP.The comparison of natural frequencies and mode shapes with available literature results confirms the precision of the theoretical formulation and numerical computations.The bending stiffnesses are analyzed.Finally,the effects of different graphene/pore distributions,length-to-thickness/width ratios,layer thickness ratios,twist angles,and rotational speeds on the natural frequencies of the system are systematically investigated.
基金supported by Beijing Natural Science Foundation(L233025)。
文摘Functionally graded material(FGM)plates are widely used in various engineering structures owing to their tailor-made mechanical properties,whereas cracked homogeneous plates constitute a canonical setting in fracture mechanics analysis.These two classes of problems respectively embody material non-uniformity and geometric discontinuity,thereby imposing more stringent requirements on numerical methods in terms of high-order field continuity and accurate defect representation.Based on the classical Kirchhoff-Love plate theory,a numerical manifold method(MLS-NMM)incorporating moving least squares(MLS)interpolation is developed for bending analysis of FGM plates and fracture simulation of homogeneous plates with defects.The method constructs an H^(2)-regular approximation with high-order continuous weighting functions and,combined with the separation of mathematical and physical covers,establishes a unified framework that accurately handles material gradients and cracks without mesh reconstruction.For the crack tip,a singular physical cover incorporating the Williams asymptotic field is introduced to achieve local enrichment,enabling the natural capture of displacement discontinuity and stress singularity.Stress intensity factors are extracted using the interaction integral method,and the dimensionless J-integral shows a maximum relative error below 1.2%compared with the reference solution.Numerical results indicate that MLS-NMM exhibits excellent convergence performance:using 676 mathematical nodes,the nondimensional central deflection of both FGM and homogeneous plates agrees with reference solutions with a maximum relative error below 0.81%,and no shear locking occurs.A systematic analysis reveals that for a simply supported on all four edges(SSSS)FGM square plate with a/h=10,the nondimensional central deflection increases by 212%as the gradient index nrises from 0 to 5.For a homogeneous plate containing a central crack with c/a=0.6,the nondimensional central deflection increases by approximately 46%compared with the intact plate.Under weak boundary constraints(e.g.,SFSF),the deformation is markedly amplified,with the deflection reaching more than three times that under strong constraints(SCSC).The proposed method provides an efficient,reconstruction-free numerical tool for high-accuracy bending and fracture analyses of FGM and cracked thin-plate structures.
文摘Objective: To investigate the therapeutic advantages of closed reduction and Kirschner wire fixation versus open reduction and plate fixation in patients with hand surgery fractures. Methods: The sample was collected from May 2021 to May 2025, consisting of 80 patients with hand surgery fractures. These patients were randomly divided into two groups using the red and blue ball method: the plate fixation group (40 cases, treated with open reduction and plate fixation) and the Kirschner wire fixation group (40 cases, treated with closed reduction and Kirschner wire fixation). The therapeutic effects between the two groups were randomly compared. Results: The Kirschner wire fixation group outperformed the plate fixation group in all indicators except for hand function scores (p < 0.05). There was no statistically significant difference in hand function scores between the two groups (p > 0.05). Conclusion: Compared with open reduction and plate fixation, closed reduction and Kirschner wire fixation for patients with hand surgery fractures achieves a more pronounced therapeutic effect, with advantages such as less trauma, shorter operation time, less bleeding, and a lower incidence of complications. It is suitable for hand surgery fractures with good stability. Open reduction and plate internal fixation have greater advantages in complex fractures and cases requiring high stability, and are worthy of promotion and application.
基金supported by the National Key R&D Program of China (No. 2018YFA0707300)the National Natural Science Foundation of China (No. 52374376)the Introduction Plan for High end Foreign Experts, China (No. G2023105001L)。
文摘Titanium plates with a Ti−O solid solution surface-hardened layer were cold roll-bonded with 304 stainless steel plates with high work hardening rates.The evolution and mechanisms affecting the interfacial bonding strength in titanium/stainless steel laminated composites were investigated.Results indicate that the hardened layer reduces the interfacial bonding strength from over 261 MPa to less than 204 MPa.During the cold roll-bonding process,the hardened layer fractures,leading to the formation of multi-scale cracks that are difficult for the stainless steel to fill.This not only hinders the development of an interlocking interface but also leads to the presence of numerous microcracks and hardened blocks along the nearly straight interface,consequently weakening the interfacial bonding strength.In metals with high work hardening rates,the conventional approach of enhancing interface interlocking and improving interfacial bonding strength by using a surface-hardened layer becomes less effective.
文摘On January 7,2025,01:05:15 UTC(9:05 a.m.local time)southern Tibet was rocked by a M_(W)7.1 earthquake(M_(W)=moment magnitude,USGS)centered(28.639°N 87.361°E)in the Lhasa Block north of the India/Eurasia Plate boundary,in a remote area about 180 km SW of Xigaze,in Dingri County of Shigatse of the Xizang Autonomous Region(Figure 1).
文摘On February 8,2025,a remote area in the Caribbean Sea was rocked by a large M_(W)7.6(USGS,2025) earthquake,centered 209 km SSW of Georgetown,the capital of the Cayman Islands,and the largest city(population~41 000) of the British Overseas Territories(Figure 1).The earthquake was significant due to its large magnitude,potential regional impact,and the possibility of generating a tsunami.
