Owing to their rolling friction,two-dimensional piston pumps are highly suitable as power components for electro-hydrostatic actuators(EHAs).These pumps are particularly advantageous for applications requiring high ef...Owing to their rolling friction,two-dimensional piston pumps are highly suitable as power components for electro-hydrostatic actuators(EHAs).These pumps are particularly advantageous for applications requiring high efficiency and reliability.However,the ambiguity surrounding the output flow characteristics of individual two-dimensional pumps poses a significant challenge in achieving precise closed-loop control of the EHA positions.To address this issue,this study established a comprehensive numerical model that included gap leakage to analyze the impact of leakage on the output flow characteristics of a two-dimensional piston pump.The validity of the numerical analysis was indirectly confirmed through meticulous measurements of the leakage and volumetric efficiency,ensuring robust results.The research findings indicated that,at lower pump speeds,leakage significantly affected the output flow rate,leading to potential inefficiencies in the system.Conversely,at higher rotational speeds,the impact of leakage was less pronounced,implying that the influence of leakage on the pump outlet flow must be carefully considered and managed for EHAs to perform position servo control.Additionally,the research demonstrates that two-dimensional motion does not have a unique or additional effect on pump leakage,thus simplifying the design considerations.Finally,the study concluded that maintaining an oil-filled leakage environment is beneficial because it helps reduce the impact of leakage and enhances the overall volumetric efficiency of the pump system.展开更多
An aviation hydraulic axial piston pump＇s degradation fiom comprehensive wear is a typical gradual failure model. Accurate wear prediction is difficult as random and uncertain char- acteristics must be factored into ...An aviation hydraulic axial piston pump＇s degradation fiom comprehensive wear is a typical gradual failure model. Accurate wear prediction is difficult as random and uncertain char- acteristics must be factored into the estimation. The internal wear status of the axial piston pump is characterized by the return oil flow based on fault mechanism analysis of the main frictional pairs in the pump. The performance degradation model is described by the Wiener process to predict the remaining useful life （RUL） of the pump. Maximum likelihood estimation （MLE） is performed by utilizing the expectation maximization （EM） algorithm to estimate the initial parameters of the Wiener process while recursive estimation is conducted utilizing the Kalman filter method to estimate the drift coefficient of the Wiener process. The RUL of the pump is then calculated accord- ing to the performance degradation model based on the Wiener process. Experimental results indi- cate that the return oil flow is a suitable characteristic for reflecting the internal wear status of the axial piston pump, and thus the Wiener process-based method may effectively predicate the RUL of the pump.展开更多
The limit working parameters and service life of axial piston pump are determined by the carrying ability and lubrication characteristic of its key friction pairs. Therefore, the design and optimization of the key fri...The limit working parameters and service life of axial piston pump are determined by the carrying ability and lubrication characteristic of its key friction pairs. Therefore, the design and optimization of the key friction pairs are always a key and difficult problem in the research on axial piston pump. In the traditional research on piston/cylinder pair, the assembly relationship of piston and cylinder bore is simplified into ideal cylindrical pair, which can not be used to analyze the influences of radial micro-motion of piston on the distribution characteristics of oil-film thickness and pressure in details. In this paper, based on the lubrication theory of the oil film, a numerical simulation model is built, taking the influences of roughness, elastic deformation of piston and pressure-viscosity effect into consideration. With the simulation model, the dynamic characteristics of the radial micro-motion and pressure distribution are analyzed, and the relationships between radial micro-motion and carrying ability, lubrication condition, and abrasion are discussed. Furthermore, a model pump for pressure distribution measurement of oil film between piston and cylinder bore is designed. The comparison of simulation and experimental results of pressure distribution shows that the simulation model has high accuracy. The experiment and simulation results demonstrate that the pressure distribution has peak values that are much higher than the boundary pressure in the piston chamber due to the radial micro-motion, and the abrasion of piston takes place mainly on the hand close to piston ball. In addition, improvement of manufacturing roundness and straightness of piston and cylinder bore is helpful to improve the carrying ability of piston/cylinder pair. The proposed research provides references for designing piston/cylinder pair, and helps to prolong the service life of axial piston pump.展开更多
This paper presents a kind of modeling approach to the study of the thermal-hydraulic piston pump which is used in the airplane comprehensively. A set of lumped parameter mathematical models are developed which are ba...This paper presents a kind of modeling approach to the study of the thermal-hydraulic piston pump which is used in the airplane comprehensively. A set of lumped parameter mathematical models are developed which are based on conservation of energy. Heat transfer analysis for the piston pump is also given in the paper in which the heat flow inside the piston pump is described precisely. The theoretical basis and modeling stratagy are applied in a typical thermal-hydraulic circuit containing the piston pump. Simulation results are presented which show a comparison of model/rig performance and the agreement obtained demonstrates the validity of the modeling approach.展开更多
A particular emphasis is placed on the virtual prototype technology （VPT） of axial piston pump. With this technology it is convenient and flexible to build a complicated 3D virtual based on real physical model. The ...A particular emphasis is placed on the virtual prototype technology （VPT） of axial piston pump. With this technology it is convenient and flexible to build a complicated 3D virtual based on real physical model. The actual kinematics pairs of the parts were added on the model. The fluid characters were calculated by hydraulic software. The shape of the parts, the flexible body of parts, etc were improved in this prototype. So the virtual prototype of piston pump can work in computer like a real piston pump, and the flow ripple, pressure pulsation, motion principle, stress of parts, etc can be investigated. The development of the VPT is introduced at the beginning, and the modeling process of the virtual prototype is explained. Then a special emphasis is laid on the relationship between the dynamics model and the hydraulic model, and the simulations on the flow ripple, pressure pulsation, motion principle, the stress and strain distribution of the middle shaft and piston are operated. Finally, the advantages and disadvantages of the VPT are discussed. The improved virtual prototype of piston pump more tally with the real situation and the VPT has a great potential in simulation on hydraulic components.展开更多
Axial piston pump with pre-compression volume（PCV） has lower flow ripple in large scale of operating condition than the traditional one. However, there is lack of precise simulation model of the axial piston pump wi...Axial piston pump with pre-compression volume（PCV） has lower flow ripple in large scale of operating condition than the traditional one. However, there is lack of precise simulation model of the axial piston pump with PCV, so the parameters of PCV are difticult to be determined. A finite element simulation model for piston pump with PCV is built by considering the piston movement, the fluid characteristic（including fluid compressibility and viscosity） and the leakage flow rate. Then a test of the pump flow ripple called the secondary source method is implemented to validate the simulation model. Thirdly, by comparing results among the simulation results, test results and results from other publications at the same operating condition, the simulation model is validated and used in optimizing the axial piston pump with PCV. According to the pump flow ripples obtained by the simulation model with different PCV parameters, the flow ripple is the smallest when the PCV angle is 13~, the PCV volume is 1.3 ~ I0-4 m3 at such operating condition that the pump suction pressure is 2 MPa, the pump delivery pressure 15 MPa, the pump speed 1 000 r/min, the swash plate angle 13~. At the same time, the flow ripple can be reduced when the pump suction pressure is 2 MPa, the pump delivery pressure is 5 MPa,15 MPa, 22 MPa, pump speed is 400 r/min, 1 000 r/rain, 1 500 r/rain, the swash plate angle is ll~, 13~, 15~ and 17~, respectively. The finite element simulation model proposed provides a method for optimizing the PCV structure and guiding for designing a quieter axial piston pump.展开更多
The current research about the flow ripple of axial piston pump mainly focuses on the effect of the structure of parts on the flow ripple. Therein, the structure of parts are usually designed and optimized at rated wo...The current research about the flow ripple of axial piston pump mainly focuses on the effect of the structure of parts on the flow ripple. Therein, the structure of parts are usually designed and optimized at rated working conditions. However, the pump usually has to work in large-scale and time-variant working conditions. Therefore, the flow ripple characteristics of pump and analysis for its test accuracy with respect to variant steady-state conditions and transient conditions in a wide range of operating parameters are focused in this paper. First, a simulation model has been constructed, which takes the kinematics of oil film within friction pairs into account for higher accuracy. Afterwards, a test bed which adopts Secondary Source Method is built to verify the model. The simulation and tests results show that the angular position of the piston, corresponding to the position where the peak flow ripple is produced, varies with the different pressure. The pulsating amplitude and pulsation rate of flow ripple increase with the rise of pressure and the variation rate of pressure. For the pump working at a constant speed, the flow pulsation rate decreases dramatically with the increasing speed when the speed is less than 27.78% of the maximum speed, subsequently presents a small decrease tendency with the speed further increasing. With the rise of the variation rate of speed, the pulsating amplitude and pulsation rate of flow ripple increase. As the swash plate angle augments, the pulsating amplitude of flow ripple increases, nevertheless the flow pulsation rate decreases. In contrast with the effect of the variation of pressure, the test accuracy of flow ripple is more sensitive to the variation of speed. It makes the test accuracy above 96.20% available for the pulsating amplitude of pressure deviating within a range of ~6% from the mean pressure. However, with a variation of speed deviating within a range of ±2% from the mean speed, the attainable test accuracy of flow ripple is above 93.07%. The model constructed in this research proposes a method to determine the flow ripple characteristics of pump and its attainable test accuracy under the large-scale and time-variant working conditions. Meanwhile, a discussion about the variation of flow ripple and its obtainable test accuracy with the conditions of the pump working in wide operating ranges is given as well.展开更多
The flow ripple, which is the source of noise in an axial piston pump, is widely studied today with the computational fluid dynamic（CFD） technology development. In the traditional CFD modeling, the fluid compressibi...The flow ripple, which is the source of noise in an axial piston pump, is widely studied today with the computational fluid dynamic（CFD） technology development. In the traditional CFD modeling, the fluid compressibility, which strongly influences the accuracy of the flow ripple simulation results, is often neglected. So a compressible sub-model was added with user defined function（UDF） in the CFD model to predict the flow ripple. At the same time, a test rig of flow ripple was built to study the validity of simulation. The flow ripple of pump was tested with different working parameters, including the rotation speed and the working pressure. The comparisons with experimental results show that the validity of the CFD model with compressible hydraulic oil is acceptable in analyzing the flow tipple characteristics. In this paper, the improved CFD model increases the accuracy of flow ripple rate to about one-magnitude order. Therefore, the compressible model of hydraulic oil is necessary in the flow ripple investigation of CFD simulation. The compressibility of hydraulic oil has significant effect on flow ripple, and the compression ripple takes about 88% of the total flow ripple of pump. Leakage ripple has the lowest proportion of about 4%, and geometrical ripple leakage ripple takes the remnant 8%. Besides, the influence of working parameters was investigated through the CFD simulations and experimental measurements. Comparison results show that the amplitude of flow ripple grows with the increasing of rotation speed and working pressure, and the flow ripple rate is independent of the rotation speed. However, flow ripple rate of piston pump grows with the increasing of working pressure, because the leakage ripple will increase with the pressure growing. The investigation on flow ripple of an axial piston pump using compressible hydraulic oil provides a more validity simulation model for the CFD analyzing and is beneficial to further understanding of the flow ripple characteristics in an axial piston pump.展开更多
Current researches mainly focus on the investigations of the valve plate utilizing pressure relief grooves. However,air?release and cavitation can occur near the grooves. The valve plate utilizing damping holes show e...Current researches mainly focus on the investigations of the valve plate utilizing pressure relief grooves. However,air?release and cavitation can occur near the grooves. The valve plate utilizing damping holes show excellent perfor?mance in avoiding air?release and cavitation. This study aims to reduce the noise emitted from an axial piston pump using a novel valve plate utilizing damping holes. A dynamic pump model is developed,in which the fluid properties are carefully modeled to capture the phenomena of air release and cavitation. The causes of di erent noise sources are investigated using the model. A comprehensive parametric analysis is conducted to enhance the understanding of the e ects of the valve plate parameters on the noise sources. A multi?objective genetic algorithm optimization method is proposed to optimize the parameters of valve plate. The amplitudes of the swash plate moment and flow rates in the inlet and outlet ports are defined as the objective functions. The pressure overshoot and undershoot in the piston chamber are limited by properly constraining the highest and lowest pressure values. A comparison of the various noise sources between the original and optimized designs over a wide range of pressure levels shows that the noise sources are reduced at high pressures. The results of the sound pressure level measurements show that the optimized valve plate reduces the noise level by 1.6 d B(A) at the rated working condition. The proposed method is e ective in reducing the noise of axial piston pumps and contributes to the development of quieter axial piston machines.展开更多
The optimization of the valve plate transition region is an important way of reducing the noise emission for an axial piston pump. However, the optimized methods through simulation or experiment are actually trial and...The optimization of the valve plate transition region is an important way of reducing the noise emission for an axial piston pump. However, the optimized methods through simulation or experiment are actually trial and error, and they cannot indicate the precise structural parameters of the valve plate transition region. In this study, a new design method for the transition region of valve plate based on the matching of flow area and reduction of transient reverse flow was proposed, and with which a valve plate was designed. Then, the impact of the flow ripple in the discharge line of an axial piston pump and the pressure overshoot and undershoot in the piston chamber on hydraulic and structural noise for axial piston pump is discussed. The noise reduction effect of the axial piston pump with this valve plate was analyzed by adopting a flow characteristic simulation model. Finally, the results showed that the application of this design method could contribute much to the reduction of the flow ripple and elimination of the pressure overshoot and undershoot. As a consequence, the method can be used in the design of a low-noise open circuit axial piston pump.展开更多
Axial piston pumps have been widely used in aircraft hydraulic systems to supply the system with pressurized fluid. The continuous improvement of the aircraft performance has put forward the demand on aviation piston ...Axial piston pumps have been widely used in aircraft hydraulic systems to supply the system with pressurized fluid. The continuous improvement of the aircraft performance has put forward the demand on aviation piston pumps for high power density, safety, and reliability. The lubricating interfaces in axial piston machines are the key design issue that greatly determines the pump performance and service life. The cylinder block/valve plate interface is one of these critical lubricating interfaces and has received considerable attention from many researchers in the last half century. This study aims to review the state-of-the-art literature on the cylinder block/valve plate interface comprehensively and systematically. First, we introduce various theoretical models developed to investigate the lubrication behaviors of the interface and compare them in terms of their assumptions and limitations. Second, the experimental studies on the cylinder block/valve plate interface are presented comprehensively, where the involved test rigs are divided into three types according to their fidelity levels and measurement functionality. Third, we summarize some typical approaches of structure optimization, surface shaping, and surface strengthening, which help improve the load-carrying and anti-wear capacities of the interface under severe operating conditions. Finally, the challenges and future trends of the cylinder block/valve plate interface research are discussed briefly.展开更多
Driving a hydraulic cylinder directly by a closed-loop hydraulic pump is currently a key research area in the field of electro-hydraulic control technology,and it is the most direct means to improve the energy efficie...Driving a hydraulic cylinder directly by a closed-loop hydraulic pump is currently a key research area in the field of electro-hydraulic control technology,and it is the most direct means to improve the energy efficiency of an electro-hydraulic control system.So far,this technology has been well applied to the pump-controlled symmetric hydraulic cylinder.However,for the differential cylinder that is widely used in hydraulic technology,satisfactory results have not yet been achieved,due to the asymmetric flow constraint.Therefore,based on the principle of the asymmetric valve controlled asymmetric cylinder in valve controlled cylinder technology,an innovative idea for an asymmetric pump controlled asymmetric cylinder is put forward to address this problem.The scheme proposes to transform the oil suction window of the existing axial piston pump into two series windows.When in use,one window is connected to the rod chamber of the hydraulic cylinder and the other is linked with a low-pressure oil tank.This allows the differential cylinders to be directly controlled by changing the displacement or rotation speed of the pumps.Compared with the loop principle of offsetting the area difference of the differential cylinder through hydraulic valve using existing technology,this method may simplify the circuits and increase the energy efficiency of the system.With the software SimulationX,a hydraulic pump simulation model is set up,which examines the movement characteristics of an individual piston and the compressibility of oil,as well as the flow distribution area as it changes with the rotation angle.The pump structure parameters,especially the size of the unloading groove of the valve plate,are determined through digital simulation.All of the components of the series arranged three distribution-window axial piston pump are designed,based on the simulation analysis of the flow pulse characteristics of the pump,and then the prototype pump is made.The basic characteristics,such as the pressure,flow and noise of the pumps under different rotation speeds,are measured on the test bench.The test results verify the correctness of the principle.The proposed research lays a theoretical foundation for the further development of a new pump-controlled cylinder system.展开更多
An accurate estimation of the remaining useful life（RUL） not only contributes to an effective application of an aviation piston pump, but also meets the necessity of condition based maintenance（CBM）. For the curre...An accurate estimation of the remaining useful life（RUL） not only contributes to an effective application of an aviation piston pump, but also meets the necessity of condition based maintenance（CBM）. For the current RUL evaluation methods, a model-based method is inappropriate for the degradation process of an aviation piston pump due to difficulties of modeling, while a data-based method rarely presents high-accuracy prediction in a long period of time. In this work,an adaptive-order particle filter（AOPF） prognostic process is proposed aiming at improving long-term prediction accuracy of RUL by combining both kinds of methods. A dynamic model is initialized by a data-driven or empirical method. When a new observation comes, the prior state distribution is approximated by a current model. The order of the current model is updated adaptively by fusing the information of the observation. Monte Carlo simulation is employed for estimating the posterior probability density function of future states of the pump＇s degradation.With updating the order number adaptively, the method presents a higher precision in contrast with those of traditional methods. In a case study, the proposed AOPF method is adopted to forecast the degradation status of an aviation piston pump with experimental return oil flow data, and the analytical results show the effectiveness of the proposed AOPF method.展开更多
A novel performance model of losses of pump was presented,which allows an explicit insight into the losses of various friction pairs of pump.The aim is to clarify that to what extent the hydro-mechanical losses affect...A novel performance model of losses of pump was presented,which allows an explicit insight into the losses of various friction pairs of pump.The aim is to clarify that to what extent the hydro-mechanical losses affect efficiency,and to further gain an insight into the variation and distribution characteristics of hydro-mechanical losses over wide operating ranges.A good agreement is found in the comparisons between simulation and experimental results.At rated speed,the hydro-mechanical losses take a proportion ranging from 87% to 89% and from 68% to 97%,respectively,of the total power losses of pump working under 5 MPa pressure conditions,and 13% of full displacement conditions.Furthermore,within the variation of speed ranging from 48% to 100% of rated speed,and pressure ranging from 14% to 100% of rated pressure,the main sources of hydro-mechanical losses change to slipper swash plate pair and valve plate cylinder pair at low displacement conditions,from the piston cylinder pair and slipper swash plate pair at full displacement conditions.Besides,the hydro-mechanical losses in ball guide retainer pair are found to be almost independent of pressure.The derived conclusions clarify the main orientations of efforts to improve the efficiency performance of pump,and the proposed model can service for the design of pump with higher efficiency performance.展开更多
Based on the structure of a certain type of aviation axial-piston pump＇s valve plate which adopts a pre-pressurization fluid path （consisting a damping hole, a buffer chamber, and an orifice） to reduce flow ripple,...Based on the structure of a certain type of aviation axial-piston pump＇s valve plate which adopts a pre-pressurization fluid path （consisting a damping hole, a buffer chamber, and an orifice） to reduce flow ripple, a single-piston model of the aviation axial-piston pump is presented. This sin- gle-piston model comprehensively considers fluid compressibility, orifice restriction effect, fluid resistance in the capillary tube, and the leakage flow. Besides, the instantaneous discharge areas used in the single-piston model have been calculated in detail. Based on the single-piston model, a multi-piston pump model has been established according to the simple hydraulic circuit. The sin- gle- and multi-piston pump models have been realized by the S-function in Matlab/Simulink. The developed multi-piston pump model has been validated by being compared with the numerical result by computational fluid dynamic （CFD）. The effects of the pre-pressurization fluid path on the flow ripple and the instantaneous pressure in the piston chamber have been studied and opti- mized design recommendations for the aviation axial-piston pump have been given out.展开更多
Raising the rotational speed of an axial piston pump is useful for improving its power density;however,the churning losses of the piston increase significantly with increasing speed,and this reduces the performance an...Raising the rotational speed of an axial piston pump is useful for improving its power density;however,the churning losses of the piston increase significantly with increasing speed,and this reduces the performance and efficiency of the axial piston pump.Currently,there has been some research on the churning losses of pistons;however,it has rarely been analyzed from the perspective of the piston number.To improve the performance and efficiency of the axial piston pump,a computational fluid dynamics(CFD)simulation model of the churning loss was established,and the effect of piston number on the churning loss was studied in detail.The simulation analysis results revealed that the churning losses initially increased as the number of pistons increased;however,when the number of pistons increased from six to nine,the torque of the churning losses decreased because of the hydrodynamic shadowing effect.In addition,in the analysis of cavitation results,it was determined that the cavitation area of the axial piston pump was mainly concentrated around the piston,and the cavitation became increasingly severe as the speed increased.By comparing the simulation results with and without the cavitation model,it was observed that the cavitation phenomenon is beneficial for the reduction of churning losses.In this study,a piston churning loss test rig that can eliminate other friction losses was established to verify the accuracy of the simulation results.A comparative analysis indicated that the simulation results were consistent with the actual situation.In addition,this study also conducted a simulation study on seven and nine piston pumps with the same displacement.The simulation results revealed that churning losses of the seven pistons were generally greater than those of the nine pistons under the same displacement.In addition,regarding the same piston number and displacement,reducing the pitch circle radius of piston bores is effective in reducing the churning loss.This research analyzes the effect of piston number on the churning loss,which has certain guiding significance for the structural design and model selection of axial piston pumps.展开更多
The interface between the slipper/swash plate is one of the most important frication pairs in axial piston pumps.The test of this interface in a real pump is very challenging.In this paper,a novel pump prototype is de...The interface between the slipper/swash plate is one of the most important frication pairs in axial piston pumps.The test of this interface in a real pump is very challenging.In this paper,a novel pump prototype is designed and a test rig is set up to study the dynamic lubricating performance of the slipper/swash-plate interface in axial piston machines.Such an experimental setup can simulate the operating condition of a real axial piston pump without changing the relative motion relationship of the interfaces.Considering the lubricant oil film thickness as the main measurement parameter,the attitude of the slipper under the conditions of different load pressure,rotation speed and charge pressure are studied experimentally.After the test,the wear state of the swash plate is observed.According to the friction trace on the surface of the swash plate,the prediction for the attitude of the slipper and the zone easy to wear are verified.展开更多
Increasing the rotating speed is considered as an efficient approach to upgrade the power-to-weight ratio in an axial piston pump,but penalized by more leakage and more severe wear resulting from the adverse cylinder ...Increasing the rotating speed is considered as an efficient approach to upgrade the power-to-weight ratio in an axial piston pump,but penalized by more leakage and more severe wear resulting from the adverse cylinder block tilt.Previous studies mainly focused on the bearing characteristic of the valve plate/cylinder block pair,but the spline coupling also plays a key role in the undesired cylinder block tilt,which has been little studied.A theoretical model for the rotating assembly is presented to investigate the effect of the spline coupling length on the cylinder block tilt and the performance of the valve plate/cylinder block pair.A typical high-speed axial piston pump with the displacement of 5.2 mL/r at 10000 r/min was studied by simulation and experiment.It shows that the optimal spline coupling length is one value increased by 2 mm from the original,bringing a remarkable leakage reduction under the high-speed condition by decreasing the cylinder block tilting angle.The experiment result matches well with the simulation.The influences of the spline coupling on the cylinder block tilt and the leakage were demonstrated.展开更多
This study presents a novel roller piston pump,in which a cam guide-roller type rolling support is adopted to replace the sliding pair support of the swash plate-slipper pair to achieve the oil suction and discharge o...This study presents a novel roller piston pump,in which a cam guide-roller type rolling support is adopted to replace the sliding pair support of the swash plate-slipper pair to achieve the oil suction and discharge of the piston cavity.In addition,the shaft distribution is used to replace the original valve plate distribution and the driving shaft is used as the distribution shaft to remove the valve plate structure,which greatly simplifies the design of the axial piston pump.Such a configuration largely reduces the number of sliding friction pairs of the pump,and avoids the influence of the sliding friction pair on it under high-speed and variable-speed conditions.Firstly,mathematical models of the mechanical and volumetric efficiencies of the roller pump are deduced respectively through force analysis and the compressibility equation.Based on the numerical simulation of MATLAB and AMESim,the effects of load pressure and rotational speed on mechanical and volumetric efficiencies are studied respectively,and it is verified that the roller pump has no structural flow pulsation.The prototype pump is then designed and built,along with a special test rig.The outlet pressure,outlet flow,and torque of the pump under different load pressures and rotational speeds are measured,and the mechanical and volumetric efficiencies of the prototype pump under various load pressures and rotational speeds are obtained.The experimental results are in good agreement with the simulated analysis.When the load pressure is 8 MPa and the speed is 5000 r/min,the mechanical and the volumetric efficiencies are 85.5% and 96.8%,respectively.When the speed is increased to 10000 r/min,the mechanical and the volumetric efficiencies are 66.7% and 95.6%,respectively.The experimental results show that the proposed roller piston pump has excellent efficiency under wide-speed and high-speed conditions and can be a potential solution as a fuel pump in aerospace fuel systems.展开更多
This study investigates tribological performance of MoS2 coating on slipper pair in axial piston pump.Firstly,the MoS2 coating on the surface of slipper pair was prepared by atmospheric plasma spraying treatment techn...This study investigates tribological performance of MoS2 coating on slipper pair in axial piston pump.Firstly,the MoS2 coating on the surface of slipper pair was prepared by atmospheric plasma spraying treatment technology.Secondly,the tribological characteristics of slipper pair under various working conditions were evaluated on ring-on-block tester in oil lubrication.The original and worn surfaces of the specimens were analyzed with scanning electron microscope and energy dispersive spectrometer,and then the wear morphologies of the MoS2 coatings were imaged by X-ray photoelectron spectroscopy.The experimental results showed that the friction coefficients of Cu-based materials with MoS2 coating decreased by about 0.05 at 800 N.Especially,when the external load was set to 800 N,the wear rate of the ZY331608 decreased by about 16.4%after the substrates were treated by the MoS2 coating,which exhibited excellent anti-friction and wear resistance.The formation of the MoS2 lubricating film could be classified into four stages,including the initial friction stage,anchoring stage of MoS2 on friction surface,covering stage of the sliding surface by MoS2 and the formation stage of MoS2 film.The dominating wear mechanisms of Cu-based materials with MoS2 coating were adhesive wear and abrasive wear accompanied with oxidative wear.展开更多
基金Supported by National Natural Science Foundation of China(Grant No.52205072).
文摘Owing to their rolling friction,two-dimensional piston pumps are highly suitable as power components for electro-hydrostatic actuators(EHAs).These pumps are particularly advantageous for applications requiring high efficiency and reliability.However,the ambiguity surrounding the output flow characteristics of individual two-dimensional pumps poses a significant challenge in achieving precise closed-loop control of the EHA positions.To address this issue,this study established a comprehensive numerical model that included gap leakage to analyze the impact of leakage on the output flow characteristics of a two-dimensional piston pump.The validity of the numerical analysis was indirectly confirmed through meticulous measurements of the leakage and volumetric efficiency,ensuring robust results.The research findings indicated that,at lower pump speeds,leakage significantly affected the output flow rate,leading to potential inefficiencies in the system.Conversely,at higher rotational speeds,the impact of leakage was less pronounced,implying that the influence of leakage on the pump outlet flow must be carefully considered and managed for EHAs to perform position servo control.Additionally,the research demonstrates that two-dimensional motion does not have a unique or additional effect on pump leakage,thus simplifying the design considerations.Finally,the study concluded that maintaining an oil-filled leakage environment is beneficial because it helps reduce the impact of leakage and enhances the overall volumetric efficiency of the pump system.
基金supported by the National Natural Science Foundation of China(No.51305011)the National Basic Research Program of China(No.2014CB046402)the 111 Project of China
文摘An aviation hydraulic axial piston pump＇s degradation fiom comprehensive wear is a typical gradual failure model. Accurate wear prediction is difficult as random and uncertain char- acteristics must be factored into the estimation. The internal wear status of the axial piston pump is characterized by the return oil flow based on fault mechanism analysis of the main frictional pairs in the pump. The performance degradation model is described by the Wiener process to predict the remaining useful life （RUL） of the pump. Maximum likelihood estimation （MLE） is performed by utilizing the expectation maximization （EM） algorithm to estimate the initial parameters of the Wiener process while recursive estimation is conducted utilizing the Kalman filter method to estimate the drift coefficient of the Wiener process. The RUL of the pump is then calculated accord- ing to the performance degradation model based on the Wiener process. Experimental results indi- cate that the return oil flow is a suitable characteristic for reflecting the internal wear status of the axial piston pump, and thus the Wiener process-based method may effectively predicate the RUL of the pump.
基金supported by National Natural Science Foundation of China(Grant No. 51075360)Doctoral Foundation of Ministry of Education of China(Grant No. 20090101110041)National Key Technology R&D Program of the Twelfth Five-year Plan of China(Grant No. 2011BAF09B03)
文摘The limit working parameters and service life of axial piston pump are determined by the carrying ability and lubrication characteristic of its key friction pairs. Therefore, the design and optimization of the key friction pairs are always a key and difficult problem in the research on axial piston pump. In the traditional research on piston/cylinder pair, the assembly relationship of piston and cylinder bore is simplified into ideal cylindrical pair, which can not be used to analyze the influences of radial micro-motion of piston on the distribution characteristics of oil-film thickness and pressure in details. In this paper, based on the lubrication theory of the oil film, a numerical simulation model is built, taking the influences of roughness, elastic deformation of piston and pressure-viscosity effect into consideration. With the simulation model, the dynamic characteristics of the radial micro-motion and pressure distribution are analyzed, and the relationships between radial micro-motion and carrying ability, lubrication condition, and abrasion are discussed. Furthermore, a model pump for pressure distribution measurement of oil film between piston and cylinder bore is designed. The comparison of simulation and experimental results of pressure distribution shows that the simulation model has high accuracy. The experiment and simulation results demonstrate that the pressure distribution has peak values that are much higher than the boundary pressure in the piston chamber due to the radial micro-motion, and the abrasion of piston takes place mainly on the hand close to piston ball. In addition, improvement of manufacturing roundness and straightness of piston and cylinder bore is helpful to improve the carrying ability of piston/cylinder pair. The proposed research provides references for designing piston/cylinder pair, and helps to prolong the service life of axial piston pump.
文摘This paper presents a kind of modeling approach to the study of the thermal-hydraulic piston pump which is used in the airplane comprehensively. A set of lumped parameter mathematical models are developed which are based on conservation of energy. Heat transfer analysis for the piston pump is also given in the paper in which the heat flow inside the piston pump is described precisely. The theoretical basis and modeling stratagy are applied in a typical thermal-hydraulic circuit containing the piston pump. Simulation results are presented which show a comparison of model/rig performance and the agreement obtained demonstrates the validity of the modeling approach.
基金supported by National Key Technology R&D Program of the 11th Five-year Plan of China (Grant No. 2006BAF01B01, 2006BAF01B04)
文摘A particular emphasis is placed on the virtual prototype technology （VPT） of axial piston pump. With this technology it is convenient and flexible to build a complicated 3D virtual based on real physical model. The actual kinematics pairs of the parts were added on the model. The fluid characters were calculated by hydraulic software. The shape of the parts, the flexible body of parts, etc were improved in this prototype. So the virtual prototype of piston pump can work in computer like a real piston pump, and the flow ripple, pressure pulsation, motion principle, stress of parts, etc can be investigated. The development of the VPT is introduced at the beginning, and the modeling process of the virtual prototype is explained. Then a special emphasis is laid on the relationship between the dynamics model and the hydraulic model, and the simulations on the flow ripple, pressure pulsation, motion principle, the stress and strain distribution of the middle shaft and piston are operated. Finally, the advantages and disadvantages of the VPT are discussed. The improved virtual prototype of piston pump more tally with the real situation and the VPT has a great potential in simulation on hydraulic components.
基金supported by National Key Technology R&D Program of the Eleventh Five-year Plan of China(Grant No.2011BAF09B03)National Natural Science Foundation of China(Grant No.51075360)
文摘Axial piston pump with pre-compression volume（PCV） has lower flow ripple in large scale of operating condition than the traditional one. However, there is lack of precise simulation model of the axial piston pump with PCV, so the parameters of PCV are difticult to be determined. A finite element simulation model for piston pump with PCV is built by considering the piston movement, the fluid characteristic（including fluid compressibility and viscosity） and the leakage flow rate. Then a test of the pump flow ripple called the secondary source method is implemented to validate the simulation model. Thirdly, by comparing results among the simulation results, test results and results from other publications at the same operating condition, the simulation model is validated and used in optimizing the axial piston pump with PCV. According to the pump flow ripples obtained by the simulation model with different PCV parameters, the flow ripple is the smallest when the PCV angle is 13~, the PCV volume is 1.3 ~ I0-4 m3 at such operating condition that the pump suction pressure is 2 MPa, the pump delivery pressure 15 MPa, the pump speed 1 000 r/min, the swash plate angle 13~. At the same time, the flow ripple can be reduced when the pump suction pressure is 2 MPa, the pump delivery pressure is 5 MPa,15 MPa, 22 MPa, pump speed is 400 r/min, 1 000 r/rain, 1 500 r/rain, the swash plate angle is ll~, 13~, 15~ and 17~, respectively. The finite element simulation model proposed provides a method for optimizing the PCV structure and guiding for designing a quieter axial piston pump.
基金Supported by National Basic Research Program of China(973 Program,Grant No.2014CB046403)National Key Technology R&D Program of the Twelfth Five-year Plan of China(Grant No.2013BAF07B01)
文摘The current research about the flow ripple of axial piston pump mainly focuses on the effect of the structure of parts on the flow ripple. Therein, the structure of parts are usually designed and optimized at rated working conditions. However, the pump usually has to work in large-scale and time-variant working conditions. Therefore, the flow ripple characteristics of pump and analysis for its test accuracy with respect to variant steady-state conditions and transient conditions in a wide range of operating parameters are focused in this paper. First, a simulation model has been constructed, which takes the kinematics of oil film within friction pairs into account for higher accuracy. Afterwards, a test bed which adopts Secondary Source Method is built to verify the model. The simulation and tests results show that the angular position of the piston, corresponding to the position where the peak flow ripple is produced, varies with the different pressure. The pulsating amplitude and pulsation rate of flow ripple increase with the rise of pressure and the variation rate of pressure. For the pump working at a constant speed, the flow pulsation rate decreases dramatically with the increasing speed when the speed is less than 27.78% of the maximum speed, subsequently presents a small decrease tendency with the speed further increasing. With the rise of the variation rate of speed, the pulsating amplitude and pulsation rate of flow ripple increase. As the swash plate angle augments, the pulsating amplitude of flow ripple increases, nevertheless the flow pulsation rate decreases. In contrast with the effect of the variation of pressure, the test accuracy of flow ripple is more sensitive to the variation of speed. It makes the test accuracy above 96.20% available for the pulsating amplitude of pressure deviating within a range of ~6% from the mean pressure. However, with a variation of speed deviating within a range of ±2% from the mean speed, the attainable test accuracy of flow ripple is above 93.07%. The model constructed in this research proposes a method to determine the flow ripple characteristics of pump and its attainable test accuracy under the large-scale and time-variant working conditions. Meanwhile, a discussion about the variation of flow ripple and its obtainable test accuracy with the conditions of the pump working in wide operating ranges is given as well.
基金supported by National Key Technology R&D Program of the Eleventh Five-year Plan of China (Grant No. 2006BAF01B01, Grant No. 2006BAF01B04)Open Foundation of State Key Laboratory of Mechanical System and Vibration of China (Grant No. MSV-2009-02)
文摘The flow ripple, which is the source of noise in an axial piston pump, is widely studied today with the computational fluid dynamic（CFD） technology development. In the traditional CFD modeling, the fluid compressibility, which strongly influences the accuracy of the flow ripple simulation results, is often neglected. So a compressible sub-model was added with user defined function（UDF） in the CFD model to predict the flow ripple. At the same time, a test rig of flow ripple was built to study the validity of simulation. The flow ripple of pump was tested with different working parameters, including the rotation speed and the working pressure. The comparisons with experimental results show that the validity of the CFD model with compressible hydraulic oil is acceptable in analyzing the flow tipple characteristics. In this paper, the improved CFD model increases the accuracy of flow ripple rate to about one-magnitude order. Therefore, the compressible model of hydraulic oil is necessary in the flow ripple investigation of CFD simulation. The compressibility of hydraulic oil has significant effect on flow ripple, and the compression ripple takes about 88% of the total flow ripple of pump. Leakage ripple has the lowest proportion of about 4%, and geometrical ripple leakage ripple takes the remnant 8%. Besides, the influence of working parameters was investigated through the CFD simulations and experimental measurements. Comparison results show that the amplitude of flow ripple grows with the increasing of rotation speed and working pressure, and the flow ripple rate is independent of the rotation speed. However, flow ripple rate of piston pump grows with the increasing of working pressure, because the leakage ripple will increase with the pressure growing. The investigation on flow ripple of an axial piston pump using compressible hydraulic oil provides a more validity simulation model for the CFD analyzing and is beneficial to further understanding of the flow ripple characteristics in an axial piston pump.
基金Supported by National Basic Research Program of China(Grant No.2014CB046403)Zhejiang Provincial Natural Science Foundation of China(Grant No.LQ14E050005)
文摘Current researches mainly focus on the investigations of the valve plate utilizing pressure relief grooves. However,air?release and cavitation can occur near the grooves. The valve plate utilizing damping holes show excellent perfor?mance in avoiding air?release and cavitation. This study aims to reduce the noise emitted from an axial piston pump using a novel valve plate utilizing damping holes. A dynamic pump model is developed,in which the fluid properties are carefully modeled to capture the phenomena of air release and cavitation. The causes of di erent noise sources are investigated using the model. A comprehensive parametric analysis is conducted to enhance the understanding of the e ects of the valve plate parameters on the noise sources. A multi?objective genetic algorithm optimization method is proposed to optimize the parameters of valve plate. The amplitudes of the swash plate moment and flow rates in the inlet and outlet ports are defined as the objective functions. The pressure overshoot and undershoot in the piston chamber are limited by properly constraining the highest and lowest pressure values. A comparison of the various noise sources between the original and optimized designs over a wide range of pressure levels shows that the noise sources are reduced at high pressures. The results of the sound pressure level measurements show that the optimized valve plate reduces the noise level by 1.6 d B(A) at the rated working condition. The proposed method is e ective in reducing the noise of axial piston pumps and contributes to the development of quieter axial piston machines.
基金the National Basic Research Program (973 Program) of China，the Science Fund for Creative Research Groups of the National Natural Science Foundation of China
文摘The optimization of the valve plate transition region is an important way of reducing the noise emission for an axial piston pump. However, the optimized methods through simulation or experiment are actually trial and error, and they cannot indicate the precise structural parameters of the valve plate transition region. In this study, a new design method for the transition region of valve plate based on the matching of flow area and reduction of transient reverse flow was proposed, and with which a valve plate was designed. Then, the impact of the flow ripple in the discharge line of an axial piston pump and the pressure overshoot and undershoot in the piston chamber on hydraulic and structural noise for axial piston pump is discussed. The noise reduction effect of the axial piston pump with this valve plate was analyzed by adopting a flow characteristic simulation model. Finally, the results showed that the application of this design method could contribute much to the reduction of the flow ripple and elimination of the pressure overshoot and undershoot. As a consequence, the method can be used in the design of a low-noise open circuit axial piston pump.
基金supported by Chinese Civil Aircraft Project [No. MJ-2017-S49]China National Postdoctoral Program for Innovative Talents [No. BX20200210]China Postdoctoral Science Foundation [No. 2019M660086]。
文摘Axial piston pumps have been widely used in aircraft hydraulic systems to supply the system with pressurized fluid. The continuous improvement of the aircraft performance has put forward the demand on aviation piston pumps for high power density, safety, and reliability. The lubricating interfaces in axial piston machines are the key design issue that greatly determines the pump performance and service life. The cylinder block/valve plate interface is one of these critical lubricating interfaces and has received considerable attention from many researchers in the last half century. This study aims to review the state-of-the-art literature on the cylinder block/valve plate interface comprehensively and systematically. First, we introduce various theoretical models developed to investigate the lubrication behaviors of the interface and compare them in terms of their assumptions and limitations. Second, the experimental studies on the cylinder block/valve plate interface are presented comprehensively, where the involved test rigs are divided into three types according to their fidelity levels and measurement functionality. Third, we summarize some typical approaches of structure optimization, surface shaping, and surface strengthening, which help improve the load-carrying and anti-wear capacities of the interface under severe operating conditions. Finally, the challenges and future trends of the cylinder block/valve plate interface research are discussed briefly.
基金supported by National Natural Science Foundation of China (Grant No. 50775156)Open Fund of The State Key Lab of Fluid Power Transmission and Control of Zhejiang University, China (Grant No. GZKF-2008006)
文摘Driving a hydraulic cylinder directly by a closed-loop hydraulic pump is currently a key research area in the field of electro-hydraulic control technology,and it is the most direct means to improve the energy efficiency of an electro-hydraulic control system.So far,this technology has been well applied to the pump-controlled symmetric hydraulic cylinder.However,for the differential cylinder that is widely used in hydraulic technology,satisfactory results have not yet been achieved,due to the asymmetric flow constraint.Therefore,based on the principle of the asymmetric valve controlled asymmetric cylinder in valve controlled cylinder technology,an innovative idea for an asymmetric pump controlled asymmetric cylinder is put forward to address this problem.The scheme proposes to transform the oil suction window of the existing axial piston pump into two series windows.When in use,one window is connected to the rod chamber of the hydraulic cylinder and the other is linked with a low-pressure oil tank.This allows the differential cylinders to be directly controlled by changing the displacement or rotation speed of the pumps.Compared with the loop principle of offsetting the area difference of the differential cylinder through hydraulic valve using existing technology,this method may simplify the circuits and increase the energy efficiency of the system.With the software SimulationX,a hydraulic pump simulation model is set up,which examines the movement characteristics of an individual piston and the compressibility of oil,as well as the flow distribution area as it changes with the rotation angle.The pump structure parameters,especially the size of the unloading groove of the valve plate,are determined through digital simulation.All of the components of the series arranged three distribution-window axial piston pump are designed,based on the simulation analysis of the flow pulse characteristics of the pump,and then the prototype pump is made.The basic characteristics,such as the pressure,flow and noise of the pumps under different rotation speeds,are measured on the test bench.The test results verify the correctness of the principle.The proposed research lays a theoretical foundation for the further development of a new pump-controlled cylinder system.
基金co-supported by the National Natural Science Foundation of China(Nos.51620105010,51575019)National Basic Research Program of China(No.2014CB046400)Program 111 of China
文摘An accurate estimation of the remaining useful life（RUL） not only contributes to an effective application of an aviation piston pump, but also meets the necessity of condition based maintenance（CBM）. For the current RUL evaluation methods, a model-based method is inappropriate for the degradation process of an aviation piston pump due to difficulties of modeling, while a data-based method rarely presents high-accuracy prediction in a long period of time. In this work,an adaptive-order particle filter（AOPF） prognostic process is proposed aiming at improving long-term prediction accuracy of RUL by combining both kinds of methods. A dynamic model is initialized by a data-driven or empirical method. When a new observation comes, the prior state distribution is approximated by a current model. The order of the current model is updated adaptively by fusing the information of the observation. Monte Carlo simulation is employed for estimating the posterior probability density function of future states of the pump＇s degradation.With updating the order number adaptively, the method presents a higher precision in contrast with those of traditional methods. In a case study, the proposed AOPF method is adopted to forecast the degradation status of an aviation piston pump with experimental return oil flow data, and the analytical results show the effectiveness of the proposed AOPF method.
基金Project(2014CB046403)supported by the National Basic Research Program of ChinaProject(2013BAF07B01)supported by the National Key Technology R&D Program of China
文摘A novel performance model of losses of pump was presented,which allows an explicit insight into the losses of various friction pairs of pump.The aim is to clarify that to what extent the hydro-mechanical losses affect efficiency,and to further gain an insight into the variation and distribution characteristics of hydro-mechanical losses over wide operating ranges.A good agreement is found in the comparisons between simulation and experimental results.At rated speed,the hydro-mechanical losses take a proportion ranging from 87% to 89% and from 68% to 97%,respectively,of the total power losses of pump working under 5 MPa pressure conditions,and 13% of full displacement conditions.Furthermore,within the variation of speed ranging from 48% to 100% of rated speed,and pressure ranging from 14% to 100% of rated pressure,the main sources of hydro-mechanical losses change to slipper swash plate pair and valve plate cylinder pair at low displacement conditions,from the piston cylinder pair and slipper swash plate pair at full displacement conditions.Besides,the hydro-mechanical losses in ball guide retainer pair are found to be almost independent of pressure.The derived conclusions clarify the main orientations of efforts to improve the efficiency performance of pump,and the proposed model can service for the design of pump with higher efficiency performance.
基金the support of the National Natural Science Foundation of China (No. 51235002)the National Science Foundation for Distinguished Young Scholars (No. 50825502)
文摘Based on the structure of a certain type of aviation axial-piston pump＇s valve plate which adopts a pre-pressurization fluid path （consisting a damping hole, a buffer chamber, and an orifice） to reduce flow ripple, a single-piston model of the aviation axial-piston pump is presented. This sin- gle-piston model comprehensively considers fluid compressibility, orifice restriction effect, fluid resistance in the capillary tube, and the leakage flow. Besides, the instantaneous discharge areas used in the single-piston model have been calculated in detail. Based on the single-piston model, a multi-piston pump model has been established according to the simple hydraulic circuit. The sin- gle- and multi-piston pump models have been realized by the S-function in Matlab/Simulink. The developed multi-piston pump model has been validated by being compared with the numerical result by computational fluid dynamic （CFD）. The effects of the pre-pressurization fluid path on the flow ripple and the instantaneous pressure in the piston chamber have been studied and opti- mized design recommendations for the aviation axial-piston pump have been given out.
基金National Natural Science Foundation of China(Grant No.52005429)Open Foundation of State Key Laboratory of Fluid Power and Mechatronic Systems of China(Grant No.GZKF-201911)National Key Research and Development Program of China(Grant No.2018YFB2000703).
文摘Raising the rotational speed of an axial piston pump is useful for improving its power density;however,the churning losses of the piston increase significantly with increasing speed,and this reduces the performance and efficiency of the axial piston pump.Currently,there has been some research on the churning losses of pistons;however,it has rarely been analyzed from the perspective of the piston number.To improve the performance and efficiency of the axial piston pump,a computational fluid dynamics(CFD)simulation model of the churning loss was established,and the effect of piston number on the churning loss was studied in detail.The simulation analysis results revealed that the churning losses initially increased as the number of pistons increased;however,when the number of pistons increased from six to nine,the torque of the churning losses decreased because of the hydrodynamic shadowing effect.In addition,in the analysis of cavitation results,it was determined that the cavitation area of the axial piston pump was mainly concentrated around the piston,and the cavitation became increasingly severe as the speed increased.By comparing the simulation results with and without the cavitation model,it was observed that the cavitation phenomenon is beneficial for the reduction of churning losses.In this study,a piston churning loss test rig that can eliminate other friction losses was established to verify the accuracy of the simulation results.A comparative analysis indicated that the simulation results were consistent with the actual situation.In addition,this study also conducted a simulation study on seven and nine piston pumps with the same displacement.The simulation results revealed that churning losses of the seven pistons were generally greater than those of the nine pistons under the same displacement.In addition,regarding the same piston number and displacement,reducing the pitch circle radius of piston bores is effective in reducing the churning loss.This research analyzes the effect of piston number on the churning loss,which has certain guiding significance for the structural design and model selection of axial piston pumps.
基金Supported by Open Foundation of the State Key Laboratory of Fluid Power and Mechatronic Systems(Grant No.201718).
文摘The interface between the slipper/swash plate is one of the most important frication pairs in axial piston pumps.The test of this interface in a real pump is very challenging.In this paper,a novel pump prototype is designed and a test rig is set up to study the dynamic lubricating performance of the slipper/swash-plate interface in axial piston machines.Such an experimental setup can simulate the operating condition of a real axial piston pump without changing the relative motion relationship of the interfaces.Considering the lubricant oil film thickness as the main measurement parameter,the attitude of the slipper under the conditions of different load pressure,rotation speed and charge pressure are studied experimentally.After the test,the wear state of the swash plate is observed.According to the friction trace on the surface of the swash plate,the prediction for the attitude of the slipper and the zone easy to wear are verified.
基金This study was co-supported by the National Key R&D Program of China(No.2019YFB2005101)National Outstanding Youth Science Foundation of China(No.51922093)+2 种基金the National Natural Science Foundation of China(No.52105075)the National Natural Science Foundation of China(No.51890882)the Natural Science Foundation of Zhejiang Province(No.LQ21E050022).
文摘Increasing the rotating speed is considered as an efficient approach to upgrade the power-to-weight ratio in an axial piston pump,but penalized by more leakage and more severe wear resulting from the adverse cylinder block tilt.Previous studies mainly focused on the bearing characteristic of the valve plate/cylinder block pair,but the spline coupling also plays a key role in the undesired cylinder block tilt,which has been little studied.A theoretical model for the rotating assembly is presented to investigate the effect of the spline coupling length on the cylinder block tilt and the performance of the valve plate/cylinder block pair.A typical high-speed axial piston pump with the displacement of 5.2 mL/r at 10000 r/min was studied by simulation and experiment.It shows that the optimal spline coupling length is one value increased by 2 mm from the original,bringing a remarkable leakage reduction under the high-speed condition by decreasing the cylinder block tilting angle.The experiment result matches well with the simulation.The influences of the spline coupling on the cylinder block tilt and the leakage were demonstrated.
基金supported by the National Key Research and Development Program of China(No.2019YFB2005202).
文摘This study presents a novel roller piston pump,in which a cam guide-roller type rolling support is adopted to replace the sliding pair support of the swash plate-slipper pair to achieve the oil suction and discharge of the piston cavity.In addition,the shaft distribution is used to replace the original valve plate distribution and the driving shaft is used as the distribution shaft to remove the valve plate structure,which greatly simplifies the design of the axial piston pump.Such a configuration largely reduces the number of sliding friction pairs of the pump,and avoids the influence of the sliding friction pair on it under high-speed and variable-speed conditions.Firstly,mathematical models of the mechanical and volumetric efficiencies of the roller pump are deduced respectively through force analysis and the compressibility equation.Based on the numerical simulation of MATLAB and AMESim,the effects of load pressure and rotational speed on mechanical and volumetric efficiencies are studied respectively,and it is verified that the roller pump has no structural flow pulsation.The prototype pump is then designed and built,along with a special test rig.The outlet pressure,outlet flow,and torque of the pump under different load pressures and rotational speeds are measured,and the mechanical and volumetric efficiencies of the prototype pump under various load pressures and rotational speeds are obtained.The experimental results are in good agreement with the simulated analysis.When the load pressure is 8 MPa and the speed is 5000 r/min,the mechanical and the volumetric efficiencies are 85.5% and 96.8%,respectively.When the speed is increased to 10000 r/min,the mechanical and the volumetric efficiencies are 66.7% and 95.6%,respectively.The experimental results show that the proposed roller piston pump has excellent efficiency under wide-speed and high-speed conditions and can be a potential solution as a fuel pump in aerospace fuel systems.
基金Project(51805376)supported by the National Natural Science Foundation of ChinaProject(LQ17E050003)supported by the Zhejiang Provincial Natural Science Foundation of China+1 种基金Project(GZKF-201719)supported by the Open Foundation of the State Key Laboratory of Fluid Power and Mechatronic Systems,ChinaProject(G20180019)supported by the Basic Scientific Research Projects Foundation of Wenzhou,China。
文摘This study investigates tribological performance of MoS2 coating on slipper pair in axial piston pump.Firstly,the MoS2 coating on the surface of slipper pair was prepared by atmospheric plasma spraying treatment technology.Secondly,the tribological characteristics of slipper pair under various working conditions were evaluated on ring-on-block tester in oil lubrication.The original and worn surfaces of the specimens were analyzed with scanning electron microscope and energy dispersive spectrometer,and then the wear morphologies of the MoS2 coatings were imaged by X-ray photoelectron spectroscopy.The experimental results showed that the friction coefficients of Cu-based materials with MoS2 coating decreased by about 0.05 at 800 N.Especially,when the external load was set to 800 N,the wear rate of the ZY331608 decreased by about 16.4%after the substrates were treated by the MoS2 coating,which exhibited excellent anti-friction and wear resistance.The formation of the MoS2 lubricating film could be classified into four stages,including the initial friction stage,anchoring stage of MoS2 on friction surface,covering stage of the sliding surface by MoS2 and the formation stage of MoS2 film.The dominating wear mechanisms of Cu-based materials with MoS2 coating were adhesive wear and abrasive wear accompanied with oxidative wear.
