We investigated the influence of PEG on the surface morphology,photocatalytic performance,photovoltaic conversion efficiency(PCE),and performance in complex environments of TiO_(2)-PEG composite films.The PEG content ...We investigated the influence of PEG on the surface morphology,photocatalytic performance,photovoltaic conversion efficiency(PCE),and performance in complex environments of TiO_(2)-PEG composite films.The PEG content was varied to further optimize the comprehensive performance of the composite films.Using titanium isopropoxide as the main raw material,TiO_(2)-PEG sol was prepared via sol-gel method and coated on the surface of photovoltaic(PV)glass by spin coating.The surface morphology and crystalline phase of the TiO_(2)-PEG film were analyzed,and the effects of the TiO_(2)-PEG film on the photocatalytic performance,PCE,contact angle,and performance in complex environments of PV glass were studied.The experimental results show that under the specified experimental conditions,when 4 g PEG10000 is added,the comprehensive performance of the coated PV glass reaches its optimum,with an average transmittance of 91.73%at 550 nm.Using methylene blue(MB)dye degradation experiments,the degradation rate after 2 hours of xenon lamp irradiation reaches 98.15%.The photovoltaic conversion efficiency of the composite film reaches 16.33%,and the contact angle is 3.28°,indicating a superhydrophilic state.It is demonstrated that the appropriate amount of PEG can enhance the transmittance,self-cleaning performance,and photovoltaic conversion efficiency of coated PV glass.展开更多
This research investigates the influence of indoor and outdoor factors on photovoltaic(PV)power generation at Utrecht University to accurately predict PV system performance by identifying critical impact factors and i...This research investigates the influence of indoor and outdoor factors on photovoltaic(PV)power generation at Utrecht University to accurately predict PV system performance by identifying critical impact factors and improving renewable energy efficiency.To predict plant efficiency,nineteen variables are analyzed,consisting of nine indoor photovoltaic panel characteristics(Open Circuit Voltage(Voc),Short Circuit Current(Isc),Maximum Power(Pmpp),Maximum Voltage(Umpp),Maximum Current(Impp),Filling Factor(FF),Parallel Resistance(Rp),Series Resistance(Rs),Module Temperature)and ten environmental factors(Air Temperature,Air Humidity,Dew Point,Air Pressure,Irradiation,Irradiation Propagation,Wind Speed,Wind Speed Propagation,Wind Direction,Wind Direction Propagation).This study provides a new perspective not previously addressed in the literature.In this study,different machine learning methods such as Multilayer Perceptron(MLP),Multivariate Adaptive Regression Spline(MARS),Multiple Linear Regression(MLR),and Random Forest(RF)models are used to predict power values using data from installed PVpanels.Panel values obtained under real field conditions were used to train the models,and the results were compared.The Multilayer Perceptron(MLP)model was achieved with the highest classification accuracy of 0.990%.The machine learning models used for solar energy forecasting show high performance and produce results close to actual values.Models like Multi-Layer Perceptron(MLP)and Random Forest(RF)can be used in diverse locations based on load demand.展开更多
Radio-photovoltaic cells(RPVCs)are able to offer high reliability and extended operational lifetimes,making them ideal for harsh-environment applications.However,the two-stage energy conversion process inherently limi...Radio-photovoltaic cells(RPVCs)are able to offer high reliability and extended operational lifetimes,making them ideal for harsh-environment applications.However,the two-stage energy conversion process inherently limits energy conversion efficiency(ECE).This study presents a novel RPVC design based on a waveguide light concentration(WLC)scheme,employing multilayer-stacked GAGG:Ce scintillation waveguides alternately loaded with^(90)Sr radioisotope sources.Electron beam irradiation tests revealed highly efficient radioluminescence(RL)emission from the edge surfaces of GAGG:Ce waveguide at electron energies exceeding 60 keV.A RPVC prototype incorporating 1.43 Ci of^(90)Sr achieved a maximum output power(Pmax)of 48.9μW,with an unprecedented ECE of 2.96%—the highest reported value for radioisotope-powered RPVCs to date.Furthermore,a multi-module integrated RPVC prototype demonstrated a Pmax of 3.17 mW,with a short circuit current of 2.23 mA and an open circuit voltage of 2.14 V.Remarkably,the device exhibited only 13.8%RL performance degradation after a 50-year equivalent electron beam irradiation(total fluence:5.625×10^(18)e/cm^(2)),confirming exceptional radiation hardness.These findings demonstrate that the WLC-based RPVCs achieve both high power output and exceptional long-term stability,representing a substantial advancement for facilitating nuclear battery applications.展开更多
Due to the high consumption of fossil fuels and the environmental challenges the world is facing, the transition towards renewable energies has become increasingly evident. Thus, enhancing the performance of different...Due to the high consumption of fossil fuels and the environmental challenges the world is facing, the transition towards renewable energies has become increasingly evident. Thus, enhancing the performance of different renewable energy systems became a fundamental research focus. Improving the annual solar photovoltaic systems efficiencies became a critical need to maintain system performance and durability. The major challenge facing solar photovoltaic system technology to be controlled and reduced is the overheating of the solar cells, where this factor not only affects panel efficiency but also causes heat-induced structural damages, and long-term exposure which may accelerate material degradation, reduce panel lifespan, and potentially develop hot spots. Among the different solutions is the use of phase change materials. This research demonstrates detailed recent literature review alongside with the appropriate classifications and critical analysis related to four distinct PCM-based cooling systems: pure PCM, composite PCM, finned PCM, and hybrid PCM systems. These PCM systems affect solar system efficiency, electrical power generation, and temperature. Findings revealed that hydrated salt HS36 and paraffin wax RT42 in pure PCM systems can highly enhance system electrical efficiency, as well as enhancements achieved through composite PCM systems incorporating multiwall carbon, graphene nanoplatelets, and magnesium oxide. Moreover, finned PCM integrated with zinc nanoparticles and aluminum fins, demonstrated promising efficiency improvements. On the other hand, hybrid PCM systems, such as PVT-RT35HC integrated with graphene nanoparticle nanofluids, show significant efficiency gains and electrical power enhancements, knowing that the majority of studies performed during the last three years were introducing hybrid cooling systems integrated with phase change materials. This research article shows the potential of PCM-based cooling solutions in advancing renewable energy technologies and covers a comprehensive review that goes through the recent studies of the last three years about employing phase-change materials as a cooling system for solar cells through different ways that can be classified into four main categories which are pure PCM, composite PCM, finned PCM and hybrid cooling systems.展开更多
Carbon-based perovskite solar cells have attracted much attention,due to their low cost,simple preparation process and high chemical stability.However,the devices exhibit low photoelectric conversion efficiency,owing ...Carbon-based perovskite solar cells have attracted much attention,due to their low cost,simple preparation process and high chemical stability.However,the devices exhibit low photoelectric conversion efficiency,owing to the presence of defects and interface impedance between the perovskite active layer and the contact interface.In order to minimize the interfacial defects and improve the charge transfer performance between the perovskite layer and the contact interface,cetyltrimethylammonium chloride(CTAC)was introduced into the lower interface of HTL-free carbon-based perovskite solar cells,because CTAC can be used as interface modification material to passivate the buried interface of perovskite and promote grain growth.It was found that CTAC can not only passivate the interface defects of perovskite,but also improve the crystalline quality of perovskite.As a result,the photovoltaic conversion efficiency of reaches 17.18%,which is 12.5%higher than that of the control group.After 20 days in air with 60%RH humidity,the cell can still maintain more than 90%of the initial efficiency,which provides a new strategy for interfacial passivation of perovskite solar cells.展开更多
A series of new polymer donors (PT-PP, PT-2fPP and PT-4fPP) were synthesized based on alkylthiophene substituted benzodithiophene (BDT-T) and pyrido[3,4-b]pyrazine (PP) building blocks and the effects of fluorination ...A series of new polymer donors (PT-PP, PT-2fPP and PT-4fPP) were synthesized based on alkylthiophene substituted benzodithiophene (BDT-T) and pyrido[3,4-b]pyrazine (PP) building blocks and the effects of fluorination on the polymer properties were explored. Photophysical properties, charge mobilities and morphologies of the three polymers have been intensively investigated. The results indicated that the introduction of the fluorine atom at meta-positions of phenyl substituted PP unit hardly affected their highest occupied molecular orbital (HOMO) level. More importantly, controlling the degree of side-chain fluorination in the polymers is crucial for optimizing the blend morphology. Three polymers showed different photovoltaic properties. The polymer solar cell (PSC) based on the single layer device structure of ITO/PEDOT:PSS/PT-4fPP:PC71BM (1:1, w:w)/ZrAcac/Al demonstrates a high power conversion efficiency (PCE) of 7.61% under the illumination of AM 1.5G,100 mW cm-2, which is the highest value for PP-based PSCs.展开更多
Inverted(p-i-n)perovskite solar cells(PSCs)are favored by researchers owing to their superior compatibility with flexible substrates and tandem device fabrication.Additionally,the hole transport layer(HTL)serves as a ...Inverted(p-i-n)perovskite solar cells(PSCs)are favored by researchers owing to their superior compatibility with flexible substrates and tandem device fabrication.Additionally,the hole transport layer(HTL)serves as a template for perovskite growth,which is critical for enhancing the device performance.However,the current research on how the HTL promotes perovskite crystallization is insufficient.Here,4PADCB,a self-assembled monolayer(SAM)hole transport material,was optimized as a superior template for perovskite growth through comparative analysis;accordingly,compact perovskite film with vertical growth was prepared.The better matched energy level alignment between 4PADCB and perovskite suppressed nonradiative recombination at the interface and enabled rapid hole extraction.Moreover,high-quality perovskite film growth on 4PADCB exhibited lower Young's modulus and less residual stress.By integrating 4PADCB into p-i-n PSCs,the optimal device achieved a power conversion efficiency of 24.80%,with an open-circuit voltage of 1.156 V,thus achieving the best rank among devices without perovskite post-treatment,additives,dopants,or intermediate layers.Furthermore,the unencapsulated device demonstrated exceptional thermostability and photostability under maximum power point tracking.Thus,this work provides a new understanding for the development of novel SAMs and perovskite growth,and it is expected to further improve device performance.展开更多
Comprehensive Summary Compared to electron transporting layer materials,the species and numbers of hole transporting layer(HTL)materials for organic solar cells(OSCs)are rare.The development of HTL materials with exce...Comprehensive Summary Compared to electron transporting layer materials,the species and numbers of hole transporting layer(HTL)materials for organic solar cells(OSCs)are rare.The development of HTL materials with excellent hole collection ability and non-corrosive nature is a long-standing issue in the field of OSCs.Herein,we designed and synthesized a series of conjugated polyelectrolytes(CPEs)with continuously varied energy levels toward HTL materials for efficient OSCs.Through a“mutual doping”treatment,we obtained a CPE composite PCT-F:POM with a WF of 5.48 eV and a conductivity of 1.56х10^(-3)S/m,meaning that a good hole collection ability can be expected for PCT-F:POM.The OSC modified by PCT-F:POM showed a high PCE of 18.0%,which was superior to the reference device with PEDOT:PSS.Moreover,the PCT-F:POM-based OSC could maintain 91%of the initial PCE value after storage of 20 d,meaning that the long-term stability of OSCs is improved by incorporating the PCT-F:POM HTL.In addition,PCT-F:POM possesses good compatibility with large-area processing technique;i.e.,a PCT-F:POM HTL was processed by the blade-coating method for fabricating 1 cm^(2)OSC,and a PCE of 15.1%could be achieved.The results suggest the promising perspective of PCT-F:POM in practical applications.展开更多
基金Funded by the Project of Guangxi Science and Technology(No.ZY24212061)the Project of Guangxi Science and Technology Major Program(No.AA24263054)the Project of Beihai Science and Technology(No.202379002)。
文摘We investigated the influence of PEG on the surface morphology,photocatalytic performance,photovoltaic conversion efficiency(PCE),and performance in complex environments of TiO_(2)-PEG composite films.The PEG content was varied to further optimize the comprehensive performance of the composite films.Using titanium isopropoxide as the main raw material,TiO_(2)-PEG sol was prepared via sol-gel method and coated on the surface of photovoltaic(PV)glass by spin coating.The surface morphology and crystalline phase of the TiO_(2)-PEG film were analyzed,and the effects of the TiO_(2)-PEG film on the photocatalytic performance,PCE,contact angle,and performance in complex environments of PV glass were studied.The experimental results show that under the specified experimental conditions,when 4 g PEG10000 is added,the comprehensive performance of the coated PV glass reaches its optimum,with an average transmittance of 91.73%at 550 nm.Using methylene blue(MB)dye degradation experiments,the degradation rate after 2 hours of xenon lamp irradiation reaches 98.15%.The photovoltaic conversion efficiency of the composite film reaches 16.33%,and the contact angle is 3.28°,indicating a superhydrophilic state.It is demonstrated that the appropriate amount of PEG can enhance the transmittance,self-cleaning performance,and photovoltaic conversion efficiency of coated PV glass.
文摘This research investigates the influence of indoor and outdoor factors on photovoltaic(PV)power generation at Utrecht University to accurately predict PV system performance by identifying critical impact factors and improving renewable energy efficiency.To predict plant efficiency,nineteen variables are analyzed,consisting of nine indoor photovoltaic panel characteristics(Open Circuit Voltage(Voc),Short Circuit Current(Isc),Maximum Power(Pmpp),Maximum Voltage(Umpp),Maximum Current(Impp),Filling Factor(FF),Parallel Resistance(Rp),Series Resistance(Rs),Module Temperature)and ten environmental factors(Air Temperature,Air Humidity,Dew Point,Air Pressure,Irradiation,Irradiation Propagation,Wind Speed,Wind Speed Propagation,Wind Direction,Wind Direction Propagation).This study provides a new perspective not previously addressed in the literature.In this study,different machine learning methods such as Multilayer Perceptron(MLP),Multivariate Adaptive Regression Spline(MARS),Multiple Linear Regression(MLR),and Random Forest(RF)models are used to predict power values using data from installed PVpanels.Panel values obtained under real field conditions were used to train the models,and the results were compared.The Multilayer Perceptron(MLP)model was achieved with the highest classification accuracy of 0.990%.The machine learning models used for solar energy forecasting show high performance and produce results close to actual values.Models like Multi-Layer Perceptron(MLP)and Random Forest(RF)can be used in diverse locations based on load demand.
基金supported by the National Key Research and Development Program of China(No.2022YFB1903200)the Electronic Components Project of China(No.2009ZYHN0003).
文摘Radio-photovoltaic cells(RPVCs)are able to offer high reliability and extended operational lifetimes,making them ideal for harsh-environment applications.However,the two-stage energy conversion process inherently limits energy conversion efficiency(ECE).This study presents a novel RPVC design based on a waveguide light concentration(WLC)scheme,employing multilayer-stacked GAGG:Ce scintillation waveguides alternately loaded with^(90)Sr radioisotope sources.Electron beam irradiation tests revealed highly efficient radioluminescence(RL)emission from the edge surfaces of GAGG:Ce waveguide at electron energies exceeding 60 keV.A RPVC prototype incorporating 1.43 Ci of^(90)Sr achieved a maximum output power(Pmax)of 48.9μW,with an unprecedented ECE of 2.96%—the highest reported value for radioisotope-powered RPVCs to date.Furthermore,a multi-module integrated RPVC prototype demonstrated a Pmax of 3.17 mW,with a short circuit current of 2.23 mA and an open circuit voltage of 2.14 V.Remarkably,the device exhibited only 13.8%RL performance degradation after a 50-year equivalent electron beam irradiation(total fluence:5.625×10^(18)e/cm^(2)),confirming exceptional radiation hardness.These findings demonstrate that the WLC-based RPVCs achieve both high power output and exceptional long-term stability,representing a substantial advancement for facilitating nuclear battery applications.
文摘Due to the high consumption of fossil fuels and the environmental challenges the world is facing, the transition towards renewable energies has become increasingly evident. Thus, enhancing the performance of different renewable energy systems became a fundamental research focus. Improving the annual solar photovoltaic systems efficiencies became a critical need to maintain system performance and durability. The major challenge facing solar photovoltaic system technology to be controlled and reduced is the overheating of the solar cells, where this factor not only affects panel efficiency but also causes heat-induced structural damages, and long-term exposure which may accelerate material degradation, reduce panel lifespan, and potentially develop hot spots. Among the different solutions is the use of phase change materials. This research demonstrates detailed recent literature review alongside with the appropriate classifications and critical analysis related to four distinct PCM-based cooling systems: pure PCM, composite PCM, finned PCM, and hybrid PCM systems. These PCM systems affect solar system efficiency, electrical power generation, and temperature. Findings revealed that hydrated salt HS36 and paraffin wax RT42 in pure PCM systems can highly enhance system electrical efficiency, as well as enhancements achieved through composite PCM systems incorporating multiwall carbon, graphene nanoplatelets, and magnesium oxide. Moreover, finned PCM integrated with zinc nanoparticles and aluminum fins, demonstrated promising efficiency improvements. On the other hand, hybrid PCM systems, such as PVT-RT35HC integrated with graphene nanoparticle nanofluids, show significant efficiency gains and electrical power enhancements, knowing that the majority of studies performed during the last three years were introducing hybrid cooling systems integrated with phase change materials. This research article shows the potential of PCM-based cooling solutions in advancing renewable energy technologies and covers a comprehensive review that goes through the recent studies of the last three years about employing phase-change materials as a cooling system for solar cells through different ways that can be classified into four main categories which are pure PCM, composite PCM, finned PCM and hybrid cooling systems.
基金National Natural Science Foundation of China (52162028)Natural Science Foundation of Jiangxi Province (20232ACB204011,20224BAB204001)+3 种基金Education Department of Jiangxi Province (GJJ2201001)Jingdezhen Municipal Science and Technology Bureau (2023GY001-16,2023ZDGG001 and 20224SF005-08)Opening Project of National Engineering Research Center for Domestic&Building Ceramics (GCZX2301)State Key Laboratory of New Ceramics and Fine Processing in Tsinghua University (KF202309,KF202414)。
文摘Carbon-based perovskite solar cells have attracted much attention,due to their low cost,simple preparation process and high chemical stability.However,the devices exhibit low photoelectric conversion efficiency,owing to the presence of defects and interface impedance between the perovskite active layer and the contact interface.In order to minimize the interfacial defects and improve the charge transfer performance between the perovskite layer and the contact interface,cetyltrimethylammonium chloride(CTAC)was introduced into the lower interface of HTL-free carbon-based perovskite solar cells,because CTAC can be used as interface modification material to passivate the buried interface of perovskite and promote grain growth.It was found that CTAC can not only passivate the interface defects of perovskite,but also improve the crystalline quality of perovskite.As a result,the photovoltaic conversion efficiency of reaches 17.18%,which is 12.5%higher than that of the control group.After 20 days in air with 60%RH humidity,the cell can still maintain more than 90%of the initial efficiency,which provides a new strategy for interfacial passivation of perovskite solar cells.
基金supported by the National Natural Science Foundation of China (51673205, 21506258)National Key Research & Development Projects of China (2017YFA0206600)+3 种基金Hunan Provincial Natural Science Foundation for Distinguished Young Scholars (2017JJ1029)Natural Science Foundation of Hunan Province (2016JJ3134)Project of Innovation-driven Plan in Central South University, China (2016CX035)the Fundamental Research Funds for the Central Universities of Central South University (2016zzts023)
文摘A series of new polymer donors (PT-PP, PT-2fPP and PT-4fPP) were synthesized based on alkylthiophene substituted benzodithiophene (BDT-T) and pyrido[3,4-b]pyrazine (PP) building blocks and the effects of fluorination on the polymer properties were explored. Photophysical properties, charge mobilities and morphologies of the three polymers have been intensively investigated. The results indicated that the introduction of the fluorine atom at meta-positions of phenyl substituted PP unit hardly affected their highest occupied molecular orbital (HOMO) level. More importantly, controlling the degree of side-chain fluorination in the polymers is crucial for optimizing the blend morphology. Three polymers showed different photovoltaic properties. The polymer solar cell (PSC) based on the single layer device structure of ITO/PEDOT:PSS/PT-4fPP:PC71BM (1:1, w:w)/ZrAcac/Al demonstrates a high power conversion efficiency (PCE) of 7.61% under the illumination of AM 1.5G,100 mW cm-2, which is the highest value for PP-based PSCs.
基金supported by the National Science Fund for Distinguished Young Scholars(21925506)National Natural Science Foundation of China(U21A20331,81903743,22209192 and 62275251)+1 种基金Natural Science Foundation of Zhejiang Province(LY24F040002)China Postdoctoral Science Foundation(2022M713242).
文摘Inverted(p-i-n)perovskite solar cells(PSCs)are favored by researchers owing to their superior compatibility with flexible substrates and tandem device fabrication.Additionally,the hole transport layer(HTL)serves as a template for perovskite growth,which is critical for enhancing the device performance.However,the current research on how the HTL promotes perovskite crystallization is insufficient.Here,4PADCB,a self-assembled monolayer(SAM)hole transport material,was optimized as a superior template for perovskite growth through comparative analysis;accordingly,compact perovskite film with vertical growth was prepared.The better matched energy level alignment between 4PADCB and perovskite suppressed nonradiative recombination at the interface and enabled rapid hole extraction.Moreover,high-quality perovskite film growth on 4PADCB exhibited lower Young's modulus and less residual stress.By integrating 4PADCB into p-i-n PSCs,the optimal device achieved a power conversion efficiency of 24.80%,with an open-circuit voltage of 1.156 V,thus achieving the best rank among devices without perovskite post-treatment,additives,dopants,or intermediate layers.Furthermore,the unencapsulated device demonstrated exceptional thermostability and photostability under maximum power point tracking.Thus,this work provides a new understanding for the development of novel SAMs and perovskite growth,and it is expected to further improve device performance.
基金support from Fundamental Research Funds for the Central Universities(buctrc202140)the National Natural Science Foundation of China(No.52273166).
文摘Comprehensive Summary Compared to electron transporting layer materials,the species and numbers of hole transporting layer(HTL)materials for organic solar cells(OSCs)are rare.The development of HTL materials with excellent hole collection ability and non-corrosive nature is a long-standing issue in the field of OSCs.Herein,we designed and synthesized a series of conjugated polyelectrolytes(CPEs)with continuously varied energy levels toward HTL materials for efficient OSCs.Through a“mutual doping”treatment,we obtained a CPE composite PCT-F:POM with a WF of 5.48 eV and a conductivity of 1.56х10^(-3)S/m,meaning that a good hole collection ability can be expected for PCT-F:POM.The OSC modified by PCT-F:POM showed a high PCE of 18.0%,which was superior to the reference device with PEDOT:PSS.Moreover,the PCT-F:POM-based OSC could maintain 91%of the initial PCE value after storage of 20 d,meaning that the long-term stability of OSCs is improved by incorporating the PCT-F:POM HTL.In addition,PCT-F:POM possesses good compatibility with large-area processing technique;i.e.,a PCT-F:POM HTL was processed by the blade-coating method for fabricating 1 cm^(2)OSC,and a PCE of 15.1%could be achieved.The results suggest the promising perspective of PCT-F:POM in practical applications.
