The corrosion behaviors of T5 （225 ℃, 6.5 h） and T6 （460 ℃, 2 h ＋ 225 ℃, 12 h） peak-aged Mg-7Gd- 5Y-1Nd-0.5Zr alloys with oxide films were investigated by optical microscope （OM）, scanning electron microsco...The corrosion behaviors of T5 （225 ℃, 6.5 h） and T6 （460 ℃, 2 h ＋ 225 ℃, 12 h） peak-aged Mg-7Gd- 5Y-1Nd-0.5Zr alloys with oxide films were investigated by optical microscope （OM）, scanning electron microscopy （SEM）, and energy-dispersive spectroscopy （EDS）. The weight loss rates and electrochemical tests were also analyzed. The thicknesses of T5 and T6 oxide films are roughly 0.6 and 1.0 μm, respectively. The components of oxide films mainly consist of O, Mg, Y, Nd, and Gd, and the T6 oxide film results in surfaces with larger peaks than T5 oxide film. In addition, Y, Nd, and Gd peaks are all higher than those of Mg-7Gd-5Y- 1Nd-0.5Zr alloys, but Mg peak is consistently far below than that of the alloys. The specimens could be arranged in de- creasing order of corrosion rates and corrosion current densi- ties： T6 oxide film 〈 T5 oxide film 〈 T6 without oxide film 〈 T5 without oxide film. The oxide films are compact to increase the corrosion resistance for Mg-7Gd-5Y-1Nd-0.5Zr alloys, which will provide a guiding insight into the corrosion and protection of Mg-RE alloys in atmospheric environments.展开更多
Strain-controlled fatigue characteristics of peakaged and over-aged Mg_(96.47)Nd_(2.9)Zn_(0.21)magnesium alloys containing 0.42Zr,including stress response,strain resistance,hysteresis loops,strain-life and correspond...Strain-controlled fatigue characteristics of peakaged and over-aged Mg_(96.47)Nd_(2.9)Zn_(0.21)magnesium alloys containing 0.42Zr,including stress response,strain resistance,hysteresis loops,strain-life and corresponding lowcycle fatigue life prediction model,were studied.In the peak-aged state(T61:540℃×8 h+200℃×14 h),the alloy shows higher cyclic stress response,but lower ductility than the alloy in the over-aged state(T6_(2):540℃×8 h+200℃×400 h).The yield strength and ultimate tensile strength of the alloy under T6_(1)-and T6_(2)-treated conditions are close.Compared with T6_(1)-treated alloy,the steady stress amplitude occurred in T6_(2)-treated alloy is due to higher ductility and more homogenous deformation.In T6_(1)state,the fatigue cracks in the alloy first initiate along the cracked persistent slip bands and then propagate in the trans-granular mode,while in the T6_(2)state,the fatigue cracks initiate along grain boundaries and then propagate in the inter-granular mode.展开更多
This article reports a systematic investigation on the relationship between the microstructure evolution and mechanical properties of as-cast Mg-9.5Gd-2.3Y-1Zn-0.5Zr(VW92,wt.%)alloy during aging treatment.The results ...This article reports a systematic investigation on the relationship between the microstructure evolution and mechanical properties of as-cast Mg-9.5Gd-2.3Y-1Zn-0.5Zr(VW92,wt.%)alloy during aging treatment.The results indicate that the alloy exhibits obvious double peak-aging characteristics at 180℃,200℃,and 220℃;the first peak-aging appeared at 96 h,48 h,and 48 h,respectively,while the second peak-aging occurred at 204 h,180 h,and 180 h,respectively.Moreover,the strengths of the first peak-aging were higher than those of the second peak-aging.Consequently,the first peak-aging at 200℃ achieved the best mechanical properties,with ultimate tensile strength(UTS),yield strength(YS),and elongation(EL)of 380(±2.0)MPa,255(±1.8)MPa,and 12.8(±1.7)%,respectively.While the strength decreased in the second peak-aging,the elongation increased to 17.2(±0.5)%.The first peak-aging strengthening is ascribed to the participation of the nano-β' phases in the matrix and the long period stacking ordered(LPSO)phases at grain boundaries(GBs).Additionally,the second peak-aging strengthening is associated with the emergence of a relatively new 3D structure comprising longchain-like structural phases β'+β'_(F) tβ_(1),γ' phases,and LPSO phases within the grain,combined with the fine and uniform LPSO phases at the GBs.展开更多
Inferior absolute strength and dissolution properties are the main bottlenecks for the widespread application of dissolvable magnesium alloys in complex working environments for unconventional oil and gas resources.He...Inferior absolute strength and dissolution properties are the main bottlenecks for the widespread application of dissolvable magnesium alloys in complex working environments for unconventional oil and gas resources.Here,a novel functional peak-aged Mg-9.5Gd-2.7Y-0.9Zn-0.8Cu-0.4Ni(wt.%) alloy for fracturing tools is reported,and it possesses an ultimate tensile strength of 457.6 MPa,ultimate compressive strength of 620.7 MPa and dissolution rate of ~43.7 mg·cm^(-2)·h^(-1) in 3 wt.% KCl solutions at 93℃.The excellent strength of the agedalloy is primarily attributed to the combination of grain refinement,long-period stacking ordered(LPSO) strengthening,and precipitation strengthening induced by stacking fault and β’ phase,among which the precipitation strengthening is dominant.Further investigations confirm that the corrosion is triggered from the micro-galvanic coupling between the Mg matrix and the cathodic lamellar and block LPSO phases.Strip-shaped corrosion pits along with LPSO phases are subsequently formed,significantly accelerating corrosion.The β’ precipitates can effectively improve the strength without compromising the dissolution rate because of their nanoscale size.This study provides an excellent material selection for dissolvable fracturing tools and presents a strategy by which a synergistic combination of strength and dissolution rate is achieved via peak-aging treatment.展开更多
基金financially supported by the National Natural Science Foundation of China(No.51204020)the National Basic Research Program of China(Nos.2013CB632202 and 2013CB632205)
文摘The corrosion behaviors of T5 （225 ℃, 6.5 h） and T6 （460 ℃, 2 h ＋ 225 ℃, 12 h） peak-aged Mg-7Gd- 5Y-1Nd-0.5Zr alloys with oxide films were investigated by optical microscope （OM）, scanning electron microscopy （SEM）, and energy-dispersive spectroscopy （EDS）. The weight loss rates and electrochemical tests were also analyzed. The thicknesses of T5 and T6 oxide films are roughly 0.6 and 1.0 μm, respectively. The components of oxide films mainly consist of O, Mg, Y, Nd, and Gd, and the T6 oxide film results in surfaces with larger peaks than T5 oxide film. In addition, Y, Nd, and Gd peaks are all higher than those of Mg-7Gd-5Y- 1Nd-0.5Zr alloys, but Mg peak is consistently far below than that of the alloys. The specimens could be arranged in de- creasing order of corrosion rates and corrosion current densi- ties： T6 oxide film 〈 T5 oxide film 〈 T6 without oxide film 〈 T5 without oxide film. The oxide films are compact to increase the corrosion resistance for Mg-7Gd-5Y-1Nd-0.5Zr alloys, which will provide a guiding insight into the corrosion and protection of Mg-RE alloys in atmospheric environments.
基金financially supported by the Key Research Project of Jiangxi Academy of Sciences(No.2017YZD2-03)the Introduction Doctoral Program of Jiangxi Academy of Sciences(No.2016-YYB-09)the Collaborative innovation GSP Project of Jiangxi Academy of Sciences(No.2016-XTPH1-09)。
文摘Strain-controlled fatigue characteristics of peakaged and over-aged Mg_(96.47)Nd_(2.9)Zn_(0.21)magnesium alloys containing 0.42Zr,including stress response,strain resistance,hysteresis loops,strain-life and corresponding lowcycle fatigue life prediction model,were studied.In the peak-aged state(T61:540℃×8 h+200℃×14 h),the alloy shows higher cyclic stress response,but lower ductility than the alloy in the over-aged state(T6_(2):540℃×8 h+200℃×400 h).The yield strength and ultimate tensile strength of the alloy under T6_(1)-and T6_(2)-treated conditions are close.Compared with T6_(1)-treated alloy,the steady stress amplitude occurred in T6_(2)-treated alloy is due to higher ductility and more homogenous deformation.In T6_(1)state,the fatigue cracks in the alloy first initiate along the cracked persistent slip bands and then propagate in the trans-granular mode,while in the T6_(2)state,the fatigue cracks initiate along grain boundaries and then propagate in the inter-granular mode.
基金supported by National Natural Science Foundation of China(No.U21A2048)the Science and Technology Research Program of the Chongqing Municipal Education Commission(No.KJZDK202201108)+2 种基金Academician in Chongqing Leaded Guidance Project of Science,Technology Innovation(No.CSTB2023YSZX-JCX0006)the Science and Technology Research Project of Chongqing Municipal Education Commission(No.KJQN202101126)Chongqing Natural Science Foundation(No.CSTB2024NSCQ-MSX0574).
文摘This article reports a systematic investigation on the relationship between the microstructure evolution and mechanical properties of as-cast Mg-9.5Gd-2.3Y-1Zn-0.5Zr(VW92,wt.%)alloy during aging treatment.The results indicate that the alloy exhibits obvious double peak-aging characteristics at 180℃,200℃,and 220℃;the first peak-aging appeared at 96 h,48 h,and 48 h,respectively,while the second peak-aging occurred at 204 h,180 h,and 180 h,respectively.Moreover,the strengths of the first peak-aging were higher than those of the second peak-aging.Consequently,the first peak-aging at 200℃ achieved the best mechanical properties,with ultimate tensile strength(UTS),yield strength(YS),and elongation(EL)of 380(±2.0)MPa,255(±1.8)MPa,and 12.8(±1.7)%,respectively.While the strength decreased in the second peak-aging,the elongation increased to 17.2(±0.5)%.The first peak-aging strengthening is ascribed to the participation of the nano-β' phases in the matrix and the long period stacking ordered(LPSO)phases at grain boundaries(GBs).Additionally,the second peak-aging strengthening is associated with the emergence of a relatively new 3D structure comprising longchain-like structural phases β'+β'_(F) tβ_(1),γ' phases,and LPSO phases within the grain,combined with the fine and uniform LPSO phases at the GBs.
基金The Major State Research and Development Program of China (No. 2021YFB3701100, No. SQ2020YFF0405156)the National Natural Science Foundation of China (No.52171097, No. 51971020)+2 种基金Beijing Laboratory of Metallic Materials and Processing for Modern Transportationthe Fundamental Research Funds for the Central Universities(No. FRF-IC-20–08)“Dingxinbeike” Project(G20200001105) for the international communication。
文摘Inferior absolute strength and dissolution properties are the main bottlenecks for the widespread application of dissolvable magnesium alloys in complex working environments for unconventional oil and gas resources.Here,a novel functional peak-aged Mg-9.5Gd-2.7Y-0.9Zn-0.8Cu-0.4Ni(wt.%) alloy for fracturing tools is reported,and it possesses an ultimate tensile strength of 457.6 MPa,ultimate compressive strength of 620.7 MPa and dissolution rate of ~43.7 mg·cm^(-2)·h^(-1) in 3 wt.% KCl solutions at 93℃.The excellent strength of the agedalloy is primarily attributed to the combination of grain refinement,long-period stacking ordered(LPSO) strengthening,and precipitation strengthening induced by stacking fault and β’ phase,among which the precipitation strengthening is dominant.Further investigations confirm that the corrosion is triggered from the micro-galvanic coupling between the Mg matrix and the cathodic lamellar and block LPSO phases.Strip-shaped corrosion pits along with LPSO phases are subsequently formed,significantly accelerating corrosion.The β’ precipitates can effectively improve the strength without compromising the dissolution rate because of their nanoscale size.This study provides an excellent material selection for dissolvable fracturing tools and presents a strategy by which a synergistic combination of strength and dissolution rate is achieved via peak-aging treatment.
