Phthalate esters(PAEs),typical pollutants widely used as plasticizers,are ubiquitous in various indoor and outdoor environments.PAEs exist in both gas and particle phases,posing risks to human health.In the present st...Phthalate esters(PAEs),typical pollutants widely used as plasticizers,are ubiquitous in various indoor and outdoor environments.PAEs exist in both gas and particle phases,posing risks to human health.In the present study,we chose four typical kinds of indoor and outdoor environments with the longest average human residence times to assess the human exposure in Hangzhou,including newly decorated residences,ordinary residences,offices and outdoor air.In order to analyze the pollution levels and characteristics of 15 gasand particle-phase PAEs in indoor and outdoor environments,air and particulate samples were collected simultaneously.The total PAEs concentrations in the four types of environments were 25,396,25,466.8,15,388.8 and 3616.2 ng/m^3,respectively.DEHP and DEP were the most abundant,and DMPP was at the lowest level.Distinct variations in the distributions of indoor/outdoor,gas/particle-phase and different molecular weights of PAEs were observed,showing that indoor environments were the main sources of PAEs pollution.While most PAEs tended to exsit in indoor sites and gas-phase,the high-molecular-weight chemicals tended to exist in the particle-phase and were mainly found in PM2.5.PAEs were more likely adsorbed by small particles,especially for the indoor environments.There existed a good correlation between the particle matter concentrations and the PAEs levels.In addition,neither temperature nor humidity had obvious effects on the distributions of the PAEs concentrations.展开更多
The effect of equal-channel angular pressing(ECAP)processing at room temperature and 300℃on the distribution of the second phase particles and its influence on hardness and electrical conductivity of the commercial C...The effect of equal-channel angular pressing(ECAP)processing at room temperature and 300℃on the distribution of the second phase particles and its influence on hardness and electrical conductivity of the commercial Cu-0.81Cr-0.07Zr alloy were investigated.Microstructural characterization indicated that the area fraction of coarse Cr-rich particles decreased after ECAP processing.This reduction was attributed to the Cr dissolution induced by plastic deformation.The electrical conductivity of the alloy decreased by 12%after 4 ECAP passes at room temperature due to the increase of electrons scattering caused by higher Cr content in solid solution and higher density of defects in the matrix.These results were supported by the reduction of the Cu lattice parameter and by the exothermic reactions,during differential scanning calorimetry(DSC)analysis,observed only in the samples subjected to ECAP processing.Aging heat treatment after ECAP processing promoted an additional hardening effect and the complete recuperation of the electrical conductivity,caused by the re-precipitation of the partially dissolved particles.The better combination of hardness(191 HV)and electrical conductivity(83.5%(IACS))was obtained after 4 ECAP passes at room temperature and subsequent aging at 380℃for 1 h.展开更多
Two types of stress relaxation tests were carried out to investigate the incubation time for incipient precipi-tation of Ti（C,N） in deformed austenite and （Ti,Mo）C in ferrite of ferritic Ti-Mo microalloyed steel T...Two types of stress relaxation tests were carried out to investigate the incubation time for incipient precipi-tation of Ti（C,N） in deformed austenite and （Ti,Mo）C in ferrite of ferritic Ti-Mo microalloyed steel The size dis-tribution, amount and chemical composition of precipitates were obtained by using physicochemical phase analysis, and calculated according to thermodynamics and kinetics. The experimental results demonstrated that the incubation time was reduced with increasing Ti content, and prolonged with the addition of Mo. After 30 % deformation at 850 ℃, the nucleation of strain-induced Ti（C,N） was a relatively slow process. On the other hand, the temperature where the nucleation rate of （Ti, Mo）C in ferrite was the highest descended first and then ascended with increasing Ti content, and so did the temperature where the incubation time was the shortest. The key point is that the tempera-ture of steel containing about 0.09 % Ti is the lowest. The mass fraction of MC-type particles with size smaller than 10 nm in steel containing 0.09% Ti and 0.2% Mo reached 73.7%. The size distributions of precipitates in steel containing 0.09% Ti were relatively concentrated compared with that in steel containing 0.07% Ti.展开更多
Nanoparticles are extensively introduced to improve the mechanical,physical,and chemical properties of alloys.In the present study,the underlying nano-refinement mechanisms of face-centered cubic Zr(Fe,Cr)_(2)secondar...Nanoparticles are extensively introduced to improve the mechanical,physical,and chemical properties of alloys.In the present study,the underlying nano-refinement mechanisms of face-centered cubic Zr(Fe,Cr)_(2)secondary phase particles(SPPs)that precipitated in Zircaloy-4 alloy under high-temperature compression were investigated in detail by utilizing high-resolution transmission electron microscopy(HRTEM)and conventional TEM techniques.The frequently observed Zr(Fe,Cr)_(2)SPPs were incoherent with the matrix and exhibited brittle fracture behaviors without measurable plasticity.HRTEM observations revealed two mechanisms underlying the nano-refinement of incoherent micro-sized SPPs via localized shear fracture on{11¯2}SPP and nanoprecipitate-assisted bending fracture,respectively.The latter was,for the first time,found to occur when the movements of large SPPs were blocked by nanometer-sized SPP during alloy deformation.Accordingly,two force models were proposed to visualize their potential nano-refinement processes.The knowledge attained from this study sheds new light on the deformation behaviors of Zr(Fe,Cr)_(2)SPPs and their associated size refinement mechanisms under high-temperature compression,and is expected to greatly benefit the process optimization of zirconium alloys to achieve precipitate nano-refinement.展开更多
The second phase particle effect on texture evolution of polycrystalline material is studied through phase-field method. A unique field variable is introduced into the phase-field model to represent the second phase p...The second phase particle effect on texture evolution of polycrystalline material is studied through phase-field method. A unique field variable is introduced into the phase-field model to represent the second phase particles. Elastic interaction between particles and grains is also considered. Results indicate that in the presence of second phase particles the average particle diameter turns smaller than in the absence of these particles and retards texture formation by pinning effect. The second phase particles change the strain energy profile, which tremendously influences the pinning effect.展开更多
The selective abnormal growth of Goss grains in magnetic sheets of Fe-3%Si （grade Hi-B） induced by second-phase particles （AlN and MnS） was studied using a modified Monte Carlo Ports model. The starting microstruc...The selective abnormal growth of Goss grains in magnetic sheets of Fe-3%Si （grade Hi-B） induced by second-phase particles （AlN and MnS） was studied using a modified Monte Carlo Ports model. The starting microstructures for the simulations were generated from electron backscatter diffraction （EBSD） orientation imaging maps of recrystallized samples. In the simulation, second-phase particles were assumed to be randomly distributed in the initial microstructures and the Zener drag effect of particles on Goss grain boundaries was assumed to be selectively invalid because of the unique properties of Goss grain boundaries. The simulation results suggest that normal growth of the matrix grains stagnates because of the pinning effect of particles on their boundaries. During the onset of abnormal grain growth, some Goss grains with concave boundaries in the initial microstructure grow fast abnormally and other Goss grains with convex boundaries shrink and eventually disappear.展开更多
The second phase particle dispersed in microalloyed steel has different effects on grain growth depending on their size and volume fiaction of the second phase particles which will change during welding thermal cycles...The second phase particle dispersed in microalloyed steel has different effects on grain growth depending on their size and volume fiaction of the second phase particles which will change during welding thermal cycles. The particle coarsening and dissolution kinetics model was analyzed for continuous heating and cooling. In addition, based on experimental data, the coupled equation of grain growth was established by introducing limited size of grain growth with the consideration of the second phase particles pinning effects. Using Monte Carlo method based on experimental data model, the grain growth simulation for heat-affected zone of microalloyed steel welds was achieved. The calculating results were well in agreement with that of experiments.展开更多
The deactivation behavior by crystallite growth of nickel nanoparticles on various supports（carbon nanofibers, zirconia, Si C, α-Al2O3 and γ-Al2O3） was investigated in the aqueous phase reforming of ethylene glyco...The deactivation behavior by crystallite growth of nickel nanoparticles on various supports（carbon nanofibers, zirconia, Si C, α-Al2O3 and γ-Al2O3） was investigated in the aqueous phase reforming of ethylene glycol. Supported Ni catalysts of ~10 wt% were prepared by impregnation of carbon nanofibers（CNF）,Zr O2, SiC, γ-Al2O3 and α-Al2O3. The extent of the Ni nanoparticle growth on various support materials follows the order CNF ~ ZrO2〉 SiC 〉 γ-Al2O3〉〉 α-Al2O3 which sequence, however, was determined by the initial Ni particle size. Based on the observed nickel leaching and the specific growth characteristics; the particle size distribution and the effect of loading on the growth rate, Ostwald ripening is suggested to be the main mechanism contributing to nickel particle growth. Remarkably, initially smaller Ni particles（~12 nm） supported on α-Al2O3 were found to outgrow Ni particles with initially larger size（~20 nm）. It is put forward that the higher susceptibility with respect to oxidation of the smaller Ni nanoparticles and differences in initial particle size distribution are responsible for this behavior.展开更多
Fast ionic conductors are one kind of solid state material with ionic conductivity as high as that of melten salts or liquid electrolytes.Ionic conductivity is one of the important parameters for characterizing a fast...Fast ionic conductors are one kind of solid state material with ionic conductivity as high as that of melten salts or liquid electrolytes.Ionic conductivity is one of the important parameters for characterizing a fast ionic conductor.For a long time materialists and chemists have made great efforts in search of new fast ionic conductors with high ionic conductivity.In view of structure,they have synthesised silver and copper fast ionic conductors with so called open structures.But it is not so successful for searching more applicable alkaline fast ionic conductors.Since polymer has flexibility for making thin film,it concentrates attention on the polymer-alkaline salt complex.Fenton et al.have first reported poly(ethylene oxide) (PEO)-alkaline salt complex.Later on Armard et al.have investigated the electrical property of PEO-NaSCN.展开更多
The equation governing the motion of a quantum particle is considered in nonrelativistic non-commutative phase space. For this aim, we first study new Poisson brackets in non-commutative phase space and obtain the mod...The equation governing the motion of a quantum particle is considered in nonrelativistic non-commutative phase space. For this aim, we first study new Poisson brackets in non-commutative phase space and obtain the modified equations of motion. Next, using novel transformations, we solve the equation of motion and report the exact analytical solutions.展开更多
Particle size and crystallinity of silicon nanoparticles were determined by analyzing the optical extinction spectra of colloidal suspensions. Experimental results from these colloids were anaiyzed using Mie theory in...Particle size and crystallinity of silicon nanoparticles were determined by analyzing the optical extinction spectra of colloidal suspensions. Experimental results from these colloids were anaiyzed using Mie theory in connection with effective medium theory, in order to determine particle sizes and their internal structure with the simple technique of optical transmission spectroscopy. By modeling an effective refractive index for the particles, the crystalline volume fraction can be extracted from extinction spectra in addition to information about the size. The crystalline volume fraction determined in this way were used to calibrate the ratio of the Raman cross sections for nanocrystalline and amorphous silicon, which was found to be σc./σa = 0.66展开更多
Nanoparticles with competitive interactions in solution can aggregate into complex structures. In this work, the synergistic self-assembles of binary particles with electrostatic and van der Waals interactions are stu...Nanoparticles with competitive interactions in solution can aggregate into complex structures. In this work, the synergistic self-assembles of binary particles with electrostatic and van der Waals interactions are studied with the particle Langevin dynamics simulation using a simple coarse-grained particle model. Various aggregations such as spherical, stacking-disk and tube structures are observed by varying the particles size and the interaction strength. The aggregation structures are explained with the packing theories of amphiphilic molecules in solution and dibolck copolymers in bulk. When the opposite ions are introduced into solution, the distribution of structures in the phase diagram appears an obvious offset. The simulation result is helpful to deeply understand the formation mechanism of complex nanostructures of multicomponent particles in solution.展开更多
The thermal radiation of micron-sized condensed phase particles plays a dominant role during the heat transfer process in aluminized Solid Rocket Motors(SRMs).Open research mainly focuses on the radiative properties o...The thermal radiation of micron-sized condensed phase particles plays a dominant role during the heat transfer process in aluminized Solid Rocket Motors(SRMs).Open research mainly focuses on the radiative properties of alumina particles while the study considering the presence of aluminum is lacking.In addition,the thermal radiation inside the SRM with consideration of the participating particles is seldom studied.In this work,the multiscale method of predicting the thermal environment inside SRMs is established from the particle radiation at microscale to the twophase flow and heat transfer at macroscale.The effective gray radiative properties of individual particles(alumina,aluminum,and hybrid alumina/aluminum)and particles cloud are investigated with the Mie theory and approximate method.Then a numerical method for predicting the thermal environment inside SRMs with considering particle radiation is established and applied in a subscale motor.The convective and radiative heat flux distributions along inner wall of motor are obtained,and it is found that the heat transfer in the combustion chamber is dominated by thermal radiation and the radiative heat flux is essentially a constant of 5.6–6.8 MW/m^(2).The convective heat transfer plays a dominant role in the nozzle and the heat flux reaches the maximum value of 11.2 MW/m^(2) near the throat.As the combustion efficiency of aluminum drops,the radiative heat flux remains unchanged in most regions and increases slightly along the diverging section wall of the nozzle.展开更多
Abnormal grain growth(AGG)has been widely observed in many friction stir welded(FSWed)joints during post-weld heat treatment(PWHT).The coarse grain structure not only reduces the strength of the joint but also limits ...Abnormal grain growth(AGG)has been widely observed in many friction stir welded(FSWed)joints during post-weld heat treatment(PWHT).The coarse grain structure not only reduces the strength of the joint but also limits its usage in superplastic forming.Several methods have been reported in previous studies to inhibit AGG,but all of them can only mitigate AGG.Complete inhibition of AGG was not achieved.In the current research,AGG was widely observed during the PWHT of friction stir welded AA6061.Multi-pass FSW enhanced the thermal stability of the as-welded grain structure but did not eliminate the occurrence of AGG.A new welding method was developed with the ball-milled Al–Ti powder mixture introduced into the stir zone and proved effective in inhibiting AGG in FSWed AA6061 during PWHT.The adoption of 5-pass FSW with an alternate rotation mode succeeded in producing an AGG-free sample.Microscopic characterizations conducted in the stir zone showed an evolution of Al–Ti powder mixture into different particle formations and Al3Ti new phase.Quantitative analysis of the second phase particles(SPPs)in the stir zone confirmed the increases in both particle number and average size.The quantitative results fit well with Humphreys’grain growth model,which theoretically explains the mechanism for AGG inhibition,i.e.,the significantly enhanced particle pinning effect.展开更多
Hot-dip Zn-Ti galvanizing can restrain the excess growth of the coating which has better corrosion resist- ances than hot-dip pure Zn. The change rules of Г2 intermetallic compound in hot-dip Zn-Ti galvanizing is inv...Hot-dip Zn-Ti galvanizing can restrain the excess growth of the coating which has better corrosion resist- ances than hot-dip pure Zn. The change rules of Г2 intermetallic compound in hot-dip Zn-Ti galvanizing is investiga ted by immersion time, titanium content and the slag test using scanning electron microscopy （SEM）, energy dis- persive spectroscopy （EDS） and X-ray diffraction （XRD）. And the mechanism of nucleation and growth of Г2 inter- metallic compound is analysed. The results show that, when adding 0. 05mass% titanium to the zinc bath, the Г2 particles form in the η layer, which nucleate by obtaining Ti atoms from the phase and Fe atoms from the dissol- ving ζ phase layer. Moreover, the more titanium is added into the bath, the more and bigger Гz particles appear. The Fz particles in the coatings grow up noticeably with prolonging the immersion time.展开更多
The effects of tungsten inert gas arc-assisted friction stir welding(TIG-FSW)on the microstructure,tensile properties and corrosion resistance of AA6016 and AA2519 alloys lap joints were investigated by means of optic...The effects of tungsten inert gas arc-assisted friction stir welding(TIG-FSW)on the microstructure,tensile properties and corrosion resistance of AA6016 and AA2519 alloys lap joints were investigated by means of optical microscope,scanning electron microscope,tensile test at room temperature,corrosion immersion tests and electrochemical measurements.The results show that the introduction of TIG arc during FSW process results in a more uniform microstructure of the joint with no tunnel hole defects.Furthermore,it enhances tensile strength and elongation of the joint with increased rates of 11.5%and 50.0%,respectively;meanwhile,the corrosion current density and largest corrosion depth are decreased with reduction rates of 78.2%and 45.7%,respectively.TIG-FSW can promote flow,contact and diffusion of materials,thus improving microstructure of the joint.Additionally,it reduces the size and number of secondary phase particles.Consequently,these factors contribute to the higher tensile properties and corrosion resistance of the joints.展开更多
Microstructure evolution and texture development and their effects on mechanical properties of a Mg-Gd-Y-Zr alloy during equal channel angular pressing（ECAP） were investigated.It is found that the microstructure is ...Microstructure evolution and texture development and their effects on mechanical properties of a Mg-Gd-Y-Zr alloy during equal channel angular pressing（ECAP） were investigated.It is found that the microstructure is still inhomogeneous after four passes,and two zones,namely the fine grain zone（FGZ） and the coarse grain zone（CGZ） are formed.The grain refinement occurs mainly by particle-stimulated nucleation（PSN） mechanism,which led to a more random texture after four passes of ECAP.In the ECAP-processed alloy,the strength did not increase while the ductility was enhanced dramatically compared with the as-received condition.The change of ductility of this alloy was discussed in terms of texture and second phase particles.展开更多
Friction stir welding (FSW) with water cooling and air cooling was used to weld 2219-T62 aluminum alloy joints with a thickness of 20 mm. The effect of cooling conditions on the corrosion resistance of joints in 3.5% ...Friction stir welding (FSW) with water cooling and air cooling was used to weld 2219-T62 aluminum alloy joints with a thickness of 20 mm. The effect of cooling conditions on the corrosion resistance of joints in 3.5% NaCl solution was investigated using the open circuit potential (OCP), the potentiodynamic polarization, and the corrosion morphology after immersing for different time. And the precipitates distribution was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results reveal that the weld nugget zone (WNZ) owning positive potential, lower corrosion current density and fine and uniform precipitates, is much more difficult to corrode than the heat affected zone (HAZ) and the base metal (BM). Compared with air-cooled joint, the water-cooled joint has better corrosion resistance. In addition, the results of microstructure observation show that the potential, distribution and size of second phase particles determine the corrosion resistance of FSW AA2219 alloy joints in chlorine-contained solution.展开更多
The effects of rare earth Ce on the microstructure and mechanical properties of impure copper containing Pb were investigated using OM,SEM,EPMA,TEM and tensile testing.TEM and EDS analysis reveal that spherical CePb3 ...The effects of rare earth Ce on the microstructure and mechanical properties of impure copper containing Pb were investigated using OM,SEM,EPMA,TEM and tensile testing.TEM and EDS analysis reveal that spherical CePb3 particles form after Ce addition.CePb3 particles,with average size of^3.6μm,homogenously distribute in the Cu matrix.Due to small lattice misfit(~4.62%)with Cu matrix,CePb3 particles can act as effective nucleation sites beneficial to the grain refinement.Pb at grain boundaries seriously deteriorates the mechanical properties of Cu.The tensile strength and the elongation of Cu-0.1 Pb are decreased by 43.1%and 56.7%compared with those of pure copper,respectively.Ce can purify grain boundaries,cause the precipitation of CePb3 particles and refine grain sizes,which contribute to significant improvement of the mechanical properties of Cu.Compared with Cu-0.1Pb,the tensile strength(179 MPa)and the elongation(38.5%)of Cu-0.1Pb-0.3Ce are increased by 117.6%and 151.6%,respectively.展开更多
Cu-Sn-Ti brazing filler is a new type of copper-based brazing filler for brazing diamond tools currently used in industry,but it suffers from poor wear resistance,high brazing temperature and low bond strength.This pa...Cu-Sn-Ti brazing filler is a new type of copper-based brazing filler for brazing diamond tools currently used in industry,but it suffers from poor wear resistance,high brazing temperature and low bond strength.This paper provides a way to improve the strength of dia-mond-brazed joints by adding zirconium carbide and tungsten carbide reinforcing phase particles to the Cu-Sn-Ti alloy,respectively.Dia-mond particles were attached to Q460 steel using Cu-Sn-Ti composite filler with the addition of the reinforcing phase,and experimental in-struments such as scanning electron microscope,X-ray diffractometer and energy spectrometer were used to investigate the brazed joint per-formance of the composite brazing material for brazing diamond.The results show that the addition of enhanced phase particles resulted in a metallurgical reaction at the joint of the composite brazed diamond,achieving a higher strength joint with no obvious cracks at the interface,while the addition of 15 wt.%WC resulted in excellent wear resistance and the highest hardness at the joint interface.展开更多
基金supported by the National Key R&D Program of China (No. 2016YFC0207103)the National Natural Science Foundation of China (No. 21607127)the Brain Bridge project with Koninklijke Philips N.V. (No. BB3-2016-01)
文摘Phthalate esters(PAEs),typical pollutants widely used as plasticizers,are ubiquitous in various indoor and outdoor environments.PAEs exist in both gas and particle phases,posing risks to human health.In the present study,we chose four typical kinds of indoor and outdoor environments with the longest average human residence times to assess the human exposure in Hangzhou,including newly decorated residences,ordinary residences,offices and outdoor air.In order to analyze the pollution levels and characteristics of 15 gasand particle-phase PAEs in indoor and outdoor environments,air and particulate samples were collected simultaneously.The total PAEs concentrations in the four types of environments were 25,396,25,466.8,15,388.8 and 3616.2 ng/m^3,respectively.DEHP and DEP were the most abundant,and DMPP was at the lowest level.Distinct variations in the distributions of indoor/outdoor,gas/particle-phase and different molecular weights of PAEs were observed,showing that indoor environments were the main sources of PAEs pollution.While most PAEs tended to exsit in indoor sites and gas-phase,the high-molecular-weight chemicals tended to exist in the particle-phase and were mainly found in PM2.5.PAEs were more likely adsorbed by small particles,especially for the indoor environments.There existed a good correlation between the particle matter concentrations and the PAEs levels.In addition,neither temperature nor humidity had obvious effects on the distributions of the PAEs concentrations.
文摘The effect of equal-channel angular pressing(ECAP)processing at room temperature and 300℃on the distribution of the second phase particles and its influence on hardness and electrical conductivity of the commercial Cu-0.81Cr-0.07Zr alloy were investigated.Microstructural characterization indicated that the area fraction of coarse Cr-rich particles decreased after ECAP processing.This reduction was attributed to the Cr dissolution induced by plastic deformation.The electrical conductivity of the alloy decreased by 12%after 4 ECAP passes at room temperature due to the increase of electrons scattering caused by higher Cr content in solid solution and higher density of defects in the matrix.These results were supported by the reduction of the Cu lattice parameter and by the exothermic reactions,during differential scanning calorimetry(DSC)analysis,observed only in the samples subjected to ECAP processing.Aging heat treatment after ECAP processing promoted an additional hardening effect and the complete recuperation of the electrical conductivity,caused by the re-precipitation of the partially dissolved particles.The better combination of hardness(191 HV)and electrical conductivity(83.5%(IACS))was obtained after 4 ECAP passes at room temperature and subsequent aging at 380℃for 1 h.
基金Item Sponsored by National Key Technology Research and Development Program in 11th Five-Year Plan of China (2006BE03A0)
文摘Two types of stress relaxation tests were carried out to investigate the incubation time for incipient precipi-tation of Ti（C,N） in deformed austenite and （Ti,Mo）C in ferrite of ferritic Ti-Mo microalloyed steel The size dis-tribution, amount and chemical composition of precipitates were obtained by using physicochemical phase analysis, and calculated according to thermodynamics and kinetics. The experimental results demonstrated that the incubation time was reduced with increasing Ti content, and prolonged with the addition of Mo. After 30 % deformation at 850 ℃, the nucleation of strain-induced Ti（C,N） was a relatively slow process. On the other hand, the temperature where the nucleation rate of （Ti, Mo）C in ferrite was the highest descended first and then ascended with increasing Ti content, and so did the temperature where the incubation time was the shortest. The key point is that the tempera-ture of steel containing about 0.09 % Ti is the lowest. The mass fraction of MC-type particles with size smaller than 10 nm in steel containing 0.09% Ti and 0.2% Mo reached 73.7%. The size distributions of precipitates in steel containing 0.09% Ti were relatively concentrated compared with that in steel containing 0.07% Ti.
文摘Nanoparticles are extensively introduced to improve the mechanical,physical,and chemical properties of alloys.In the present study,the underlying nano-refinement mechanisms of face-centered cubic Zr(Fe,Cr)_(2)secondary phase particles(SPPs)that precipitated in Zircaloy-4 alloy under high-temperature compression were investigated in detail by utilizing high-resolution transmission electron microscopy(HRTEM)and conventional TEM techniques.The frequently observed Zr(Fe,Cr)_(2)SPPs were incoherent with the matrix and exhibited brittle fracture behaviors without measurable plasticity.HRTEM observations revealed two mechanisms underlying the nano-refinement of incoherent micro-sized SPPs via localized shear fracture on{11¯2}SPP and nanoprecipitate-assisted bending fracture,respectively.The latter was,for the first time,found to occur when the movements of large SPPs were blocked by nanometer-sized SPP during alloy deformation.Accordingly,two force models were proposed to visualize their potential nano-refinement processes.The knowledge attained from this study sheds new light on the deformation behaviors of Zr(Fe,Cr)_(2)SPPs and their associated size refinement mechanisms under high-temperature compression,and is expected to greatly benefit the process optimization of zirconium alloys to achieve precipitate nano-refinement.
基金supported by the National Natural Science Foundation of China(Grant Nos.51174168,and 51274167)"111"Project,China(Grant No.B08040)
文摘The second phase particle effect on texture evolution of polycrystalline material is studied through phase-field method. A unique field variable is introduced into the phase-field model to represent the second phase particles. Elastic interaction between particles and grains is also considered. Results indicate that in the presence of second phase particles the average particle diameter turns smaller than in the absence of these particles and retards texture formation by pinning effect. The second phase particles change the strain energy profile, which tremendously influences the pinning effect.
基金financially supported by the National Key Research and Development Program of China(No 2016YFB0700505)the China’s State Grid Corporation of Science and Technology Projects(No.SGRI-WD71-13-002)+1 种基金the National Natural Science Foundation of China(Nos.51571020 and 51371030)the Nationa High Technology Research and Development Program of China(No.2015AA034201)
文摘The selective abnormal growth of Goss grains in magnetic sheets of Fe-3%Si （grade Hi-B） induced by second-phase particles （AlN and MnS） was studied using a modified Monte Carlo Ports model. The starting microstructures for the simulations were generated from electron backscatter diffraction （EBSD） orientation imaging maps of recrystallized samples. In the simulation, second-phase particles were assumed to be randomly distributed in the initial microstructures and the Zener drag effect of particles on Goss grain boundaries was assumed to be selectively invalid because of the unique properties of Goss grain boundaries. The simulation results suggest that normal growth of the matrix grains stagnates because of the pinning effect of particles on their boundaries. During the onset of abnormal grain growth, some Goss grains with concave boundaries in the initial microstructure grow fast abnormally and other Goss grains with convex boundaries shrink and eventually disappear.
文摘The second phase particle dispersed in microalloyed steel has different effects on grain growth depending on their size and volume fiaction of the second phase particles which will change during welding thermal cycles. The particle coarsening and dissolution kinetics model was analyzed for continuous heating and cooling. In addition, based on experimental data, the coupled equation of grain growth was established by introducing limited size of grain growth with the consideration of the second phase particles pinning effects. Using Monte Carlo method based on experimental data model, the grain growth simulation for heat-affected zone of microalloyed steel welds was achieved. The calculating results were well in agreement with that of experiments.
基金the support of the Smart Mix Program of The Netherlands Ministry of Economic Affairs, Agriculture and Innovation and The Netherlands Ministry of Education, Culture and Science (Grant no. 053.70.011)
文摘The deactivation behavior by crystallite growth of nickel nanoparticles on various supports（carbon nanofibers, zirconia, Si C, α-Al2O3 and γ-Al2O3） was investigated in the aqueous phase reforming of ethylene glycol. Supported Ni catalysts of ~10 wt% were prepared by impregnation of carbon nanofibers（CNF）,Zr O2, SiC, γ-Al2O3 and α-Al2O3. The extent of the Ni nanoparticle growth on various support materials follows the order CNF ~ ZrO2〉 SiC 〉 γ-Al2O3〉〉 α-Al2O3 which sequence, however, was determined by the initial Ni particle size. Based on the observed nickel leaching and the specific growth characteristics; the particle size distribution and the effect of loading on the growth rate, Ostwald ripening is suggested to be the main mechanism contributing to nickel particle growth. Remarkably, initially smaller Ni particles（~12 nm） supported on α-Al2O3 were found to outgrow Ni particles with initially larger size（~20 nm）. It is put forward that the higher susceptibility with respect to oxidation of the smaller Ni nanoparticles and differences in initial particle size distribution are responsible for this behavior.
文摘Fast ionic conductors are one kind of solid state material with ionic conductivity as high as that of melten salts or liquid electrolytes.Ionic conductivity is one of the important parameters for characterizing a fast ionic conductor.For a long time materialists and chemists have made great efforts in search of new fast ionic conductors with high ionic conductivity.In view of structure,they have synthesised silver and copper fast ionic conductors with so called open structures.But it is not so successful for searching more applicable alkaline fast ionic conductors.Since polymer has flexibility for making thin film,it concentrates attention on the polymer-alkaline salt complex.Fenton et al.have first reported poly(ethylene oxide) (PEO)-alkaline salt complex.Later on Armard et al.have investigated the electrical property of PEO-NaSCN.
基金Supported by the China Scholarship Councilthe Hanjiang Scholar Project of Shaanxi University of Technology
文摘The equation governing the motion of a quantum particle is considered in nonrelativistic non-commutative phase space. For this aim, we first study new Poisson brackets in non-commutative phase space and obtain the modified equations of motion. Next, using novel transformations, we solve the equation of motion and report the exact analytical solutions.
文摘Particle size and crystallinity of silicon nanoparticles were determined by analyzing the optical extinction spectra of colloidal suspensions. Experimental results from these colloids were anaiyzed using Mie theory in connection with effective medium theory, in order to determine particle sizes and their internal structure with the simple technique of optical transmission spectroscopy. By modeling an effective refractive index for the particles, the crystalline volume fraction can be extracted from extinction spectra in addition to information about the size. The crystalline volume fraction determined in this way were used to calibrate the ratio of the Raman cross sections for nanocrystalline and amorphous silicon, which was found to be σc./σa = 0.66
基金V. ACKNOWLEDGMENTS The computer simulation is performed on the High Performance Computing Center of Tianjin University,China. This work was supported by the National Natural Science Foundation of China （No.21274107 and No.91127046）. We thank Prof. Bin Zhang, Rui Xu, Bo Du, and Dr. Zi-lu Wang in Tianjin University for helpful discussions.
文摘Nanoparticles with competitive interactions in solution can aggregate into complex structures. In this work, the synergistic self-assembles of binary particles with electrostatic and van der Waals interactions are studied with the particle Langevin dynamics simulation using a simple coarse-grained particle model. Various aggregations such as spherical, stacking-disk and tube structures are observed by varying the particles size and the interaction strength. The aggregation structures are explained with the packing theories of amphiphilic molecules in solution and dibolck copolymers in bulk. When the opposite ions are introduced into solution, the distribution of structures in the phase diagram appears an obvious offset. The simulation result is helpful to deeply understand the formation mechanism of complex nanostructures of multicomponent particles in solution.
基金supported by the Innovative Talents Support Plan of China Postdoctoral Foundation(No.BX20180244)National Natural Science Foundation of China(No.51825604)the Fundamental Research Funds for the Central Universities of China(No.xjj2018029)。
文摘The thermal radiation of micron-sized condensed phase particles plays a dominant role during the heat transfer process in aluminized Solid Rocket Motors(SRMs).Open research mainly focuses on the radiative properties of alumina particles while the study considering the presence of aluminum is lacking.In addition,the thermal radiation inside the SRM with consideration of the participating particles is seldom studied.In this work,the multiscale method of predicting the thermal environment inside SRMs is established from the particle radiation at microscale to the twophase flow and heat transfer at macroscale.The effective gray radiative properties of individual particles(alumina,aluminum,and hybrid alumina/aluminum)and particles cloud are investigated with the Mie theory and approximate method.Then a numerical method for predicting the thermal environment inside SRMs with considering particle radiation is established and applied in a subscale motor.The convective and radiative heat flux distributions along inner wall of motor are obtained,and it is found that the heat transfer in the combustion chamber is dominated by thermal radiation and the radiative heat flux is essentially a constant of 5.6–6.8 MW/m^(2).The convective heat transfer plays a dominant role in the nozzle and the heat flux reaches the maximum value of 11.2 MW/m^(2) near the throat.As the combustion efficiency of aluminum drops,the radiative heat flux remains unchanged in most regions and increases slightly along the diverging section wall of the nozzle.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.51204108 and 51675337)the National Research Foundation for Doctoral Program of Higher Education of China(Grant No.20120073120120)the Shanghai Committee of Science and Technology(Grant No.11ZR1418100).
文摘Abnormal grain growth(AGG)has been widely observed in many friction stir welded(FSWed)joints during post-weld heat treatment(PWHT).The coarse grain structure not only reduces the strength of the joint but also limits its usage in superplastic forming.Several methods have been reported in previous studies to inhibit AGG,but all of them can only mitigate AGG.Complete inhibition of AGG was not achieved.In the current research,AGG was widely observed during the PWHT of friction stir welded AA6061.Multi-pass FSW enhanced the thermal stability of the as-welded grain structure but did not eliminate the occurrence of AGG.A new welding method was developed with the ball-milled Al–Ti powder mixture introduced into the stir zone and proved effective in inhibiting AGG in FSWed AA6061 during PWHT.The adoption of 5-pass FSW with an alternate rotation mode succeeded in producing an AGG-free sample.Microscopic characterizations conducted in the stir zone showed an evolution of Al–Ti powder mixture into different particle formations and Al3Ti new phase.Quantitative analysis of the second phase particles(SPPs)in the stir zone confirmed the increases in both particle number and average size.The quantitative results fit well with Humphreys’grain growth model,which theoretically explains the mechanism for AGG inhibition,i.e.,the significantly enhanced particle pinning effect.
基金Sponsored by Science and Technology Planning Project of Guangdong Province of China(2011B010300017)
文摘Hot-dip Zn-Ti galvanizing can restrain the excess growth of the coating which has better corrosion resist- ances than hot-dip pure Zn. The change rules of Г2 intermetallic compound in hot-dip Zn-Ti galvanizing is investiga ted by immersion time, titanium content and the slag test using scanning electron microscopy （SEM）, energy dis- persive spectroscopy （EDS） and X-ray diffraction （XRD）. And the mechanism of nucleation and growth of Г2 inter- metallic compound is analysed. The results show that, when adding 0. 05mass% titanium to the zinc bath, the Г2 particles form in the η layer, which nucleate by obtaining Ti atoms from the phase and Fe atoms from the dissol- ving ζ phase layer. Moreover, the more titanium is added into the bath, the more and bigger Гz particles appear. The Fz particles in the coatings grow up noticeably with prolonging the immersion time.
文摘The effects of tungsten inert gas arc-assisted friction stir welding(TIG-FSW)on the microstructure,tensile properties and corrosion resistance of AA6016 and AA2519 alloys lap joints were investigated by means of optical microscope,scanning electron microscope,tensile test at room temperature,corrosion immersion tests and electrochemical measurements.The results show that the introduction of TIG arc during FSW process results in a more uniform microstructure of the joint with no tunnel hole defects.Furthermore,it enhances tensile strength and elongation of the joint with increased rates of 11.5%and 50.0%,respectively;meanwhile,the corrosion current density and largest corrosion depth are decreased with reduction rates of 78.2%and 45.7%,respectively.TIG-FSW can promote flow,contact and diffusion of materials,thus improving microstructure of the joint.Additionally,it reduces the size and number of secondary phase particles.Consequently,these factors contribute to the higher tensile properties and corrosion resistance of the joints.
文摘Microstructure evolution and texture development and their effects on mechanical properties of a Mg-Gd-Y-Zr alloy during equal channel angular pressing（ECAP） were investigated.It is found that the microstructure is still inhomogeneous after four passes,and two zones,namely the fine grain zone（FGZ） and the coarse grain zone（CGZ） are formed.The grain refinement occurs mainly by particle-stimulated nucleation（PSN） mechanism,which led to a more random texture after four passes of ECAP.In the ECAP-processed alloy,the strength did not increase while the ductility was enhanced dramatically compared with the as-received condition.The change of ductility of this alloy was discussed in terms of texture and second phase particles.
基金Project (51405392) supported by the National Natural Science Foundation of ChinaProject (2019T120954) supported by the China Postdoctoral Science Foundation+1 种基金Project (3102019MS0404) supported by Fundamental Research Funds for the Central Universities, ChinaProject (2018BSHQYXMZZ31) supported by the Postdoctoral Science Foundation of Shaanxi Province, China。
文摘Friction stir welding (FSW) with water cooling and air cooling was used to weld 2219-T62 aluminum alloy joints with a thickness of 20 mm. The effect of cooling conditions on the corrosion resistance of joints in 3.5% NaCl solution was investigated using the open circuit potential (OCP), the potentiodynamic polarization, and the corrosion morphology after immersing for different time. And the precipitates distribution was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results reveal that the weld nugget zone (WNZ) owning positive potential, lower corrosion current density and fine and uniform precipitates, is much more difficult to corrode than the heat affected zone (HAZ) and the base metal (BM). Compared with air-cooled joint, the water-cooled joint has better corrosion resistance. In addition, the results of microstructure observation show that the potential, distribution and size of second phase particles determine the corrosion resistance of FSW AA2219 alloy joints in chlorine-contained solution.
基金Projects(ZR2018MEE005,ZR2018MEE016)supported by the Natural Science Foundation of Shandong Province,ChinaProject(J18KA059)supported by the Higher Educational Science and Technology Program of Shandong Province,ChinaProject(HJ16B01)supported by the Doctoral Fund of Yantai University,China。
文摘The effects of rare earth Ce on the microstructure and mechanical properties of impure copper containing Pb were investigated using OM,SEM,EPMA,TEM and tensile testing.TEM and EDS analysis reveal that spherical CePb3 particles form after Ce addition.CePb3 particles,with average size of^3.6μm,homogenously distribute in the Cu matrix.Due to small lattice misfit(~4.62%)with Cu matrix,CePb3 particles can act as effective nucleation sites beneficial to the grain refinement.Pb at grain boundaries seriously deteriorates the mechanical properties of Cu.The tensile strength and the elongation of Cu-0.1 Pb are decreased by 43.1%and 56.7%compared with those of pure copper,respectively.Ce can purify grain boundaries,cause the precipitation of CePb3 particles and refine grain sizes,which contribute to significant improvement of the mechanical properties of Cu.Compared with Cu-0.1Pb,the tensile strength(179 MPa)and the elongation(38.5%)of Cu-0.1Pb-0.3Ce are increased by 117.6%and 151.6%,respectively.
基金supported by the Anhui provincial Natural Science Foundation(No.2008085QE231).
文摘Cu-Sn-Ti brazing filler is a new type of copper-based brazing filler for brazing diamond tools currently used in industry,but it suffers from poor wear resistance,high brazing temperature and low bond strength.This paper provides a way to improve the strength of dia-mond-brazed joints by adding zirconium carbide and tungsten carbide reinforcing phase particles to the Cu-Sn-Ti alloy,respectively.Dia-mond particles were attached to Q460 steel using Cu-Sn-Ti composite filler with the addition of the reinforcing phase,and experimental in-struments such as scanning electron microscope,X-ray diffractometer and energy spectrometer were used to investigate the brazed joint per-formance of the composite brazing material for brazing diamond.The results show that the addition of enhanced phase particles resulted in a metallurgical reaction at the joint of the composite brazed diamond,achieving a higher strength joint with no obvious cracks at the interface,while the addition of 15 wt.%WC resulted in excellent wear resistance and the highest hardness at the joint interface.
