We present an estimation of depth of anomalous bodies using normalized full gradient （NFG） of gravity anomaly. Maxima in the NFG map can locate the bodies and indicate their depth. Model calculation using a sphere a...We present an estimation of depth of anomalous bodies using normalized full gradient （NFG） of gravity anomaly. Maxima in the NFG map can locate the bodies and indicate their depth. Model calculation using a sphere and application of the NFG method to gravity anomalies over salt domes in the USA and Denmark shows effectiveness of the method. However, the accuracy of depth estimation strongly depends on the number of term N in the Fourier series used to calculate the NFG. An optimum N for the calculation can be given from a test.展开更多
In order to meet the requirement of structural inspection,the crack spacing and crack width at various heights in the tensile zone of six large depth reinforced concrete beams were measured under several loading level...In order to meet the requirement of structural inspection,the crack spacing and crack width at various heights in the tensile zone of six large depth reinforced concrete beams were measured under several loading levels of serviceability state.The effects of the depth of normal section beams on the crack spacing and crack width were analyzed,and the modified model is proposed for calculating the average crack spacing by thinking about the depth of normal section,the reinforcement arrangement and the effective reinforcement ratio.The relationships of crack widths at any position in the tensile zone and at the reinforcement level on the side surface of beam were studied.By theoretical and statistical analysis,a method is proposed to calculate the ratios of crack widths between any position and the reinforcement level on the side surface of large depth reinforced concrete beams.展开更多
In this study,FLUENT software was employed to simulate the flow pattern and water depth changes in a 120° sharp bend at four discharge rates.To verify the numerical model,a 90° sharp bend was first modeled w...In this study,FLUENT software was employed to simulate the flow pattern and water depth changes in a 120° sharp bend at four discharge rates.To verify the numerical model,a 90° sharp bend was first modeled with a three-dimensional numerical model,and the results were compared with available experimental results.Based on the numerical model validation,a 120° bend was simulated.The results show that the rate of increase of the water depth at the cross-section located 40 cm before the bend,compared with the cross-sections located 40 cm and 80 cm after the bend,decreases with the increase of the normal water depth in the 120° curved channel.Moreover,with increasing normal water depth,the dimensionless water depth change decreases at all cross-sections.At the interior cross-sections of the bend,the transverse water depth slope of the inner half-width is always greater than that of the outer half-width of the channel.Hence,the water depth slope is nonlinear at each crosssection in sharp bends.Two equations reflecting the relationships between the maximum and minimum dimensionless water depths and the normal water depth throughout the channel were obtained.展开更多
基金supported by the Ministry of Science,Researches and Technology,Iran
文摘We present an estimation of depth of anomalous bodies using normalized full gradient （NFG） of gravity anomaly. Maxima in the NFG map can locate the bodies and indicate their depth. Model calculation using a sphere and application of the NFG method to gravity anomalies over salt domes in the USA and Denmark shows effectiveness of the method. However, the accuracy of depth estimation strongly depends on the number of term N in the Fourier series used to calculate the NFG. An optimum N for the calculation can be given from a test.
基金Sponsored by the Outstanding Youth Scientific Fund of Henan Province(Grant No.04120002300)Program for Innovation in University of Henan Province(Grant No.[2004]294)
文摘In order to meet the requirement of structural inspection,the crack spacing and crack width at various heights in the tensile zone of six large depth reinforced concrete beams were measured under several loading levels of serviceability state.The effects of the depth of normal section beams on the crack spacing and crack width were analyzed,and the modified model is proposed for calculating the average crack spacing by thinking about the depth of normal section,the reinforcement arrangement and the effective reinforcement ratio.The relationships of crack widths at any position in the tensile zone and at the reinforcement level on the side surface of beam were studied.By theoretical and statistical analysis,a method is proposed to calculate the ratios of crack widths between any position and the reinforcement level on the side surface of large depth reinforced concrete beams.
文摘In this study,FLUENT software was employed to simulate the flow pattern and water depth changes in a 120° sharp bend at four discharge rates.To verify the numerical model,a 90° sharp bend was first modeled with a three-dimensional numerical model,and the results were compared with available experimental results.Based on the numerical model validation,a 120° bend was simulated.The results show that the rate of increase of the water depth at the cross-section located 40 cm before the bend,compared with the cross-sections located 40 cm and 80 cm after the bend,decreases with the increase of the normal water depth in the 120° curved channel.Moreover,with increasing normal water depth,the dimensionless water depth change decreases at all cross-sections.At the interior cross-sections of the bend,the transverse water depth slope of the inner half-width is always greater than that of the outer half-width of the channel.Hence,the water depth slope is nonlinear at each crosssection in sharp bends.Two equations reflecting the relationships between the maximum and minimum dimensionless water depths and the normal water depth throughout the channel were obtained.
