The rapid industrial growth and increasing population have led to significant pollution and deterioration of the natural atmospheric environment.Major atmospheric pollutants include NO_(2)and CO_(2).Hence,it is impera...The rapid industrial growth and increasing population have led to significant pollution and deterioration of the natural atmospheric environment.Major atmospheric pollutants include NO_(2)and CO_(2).Hence,it is imperative to develop NO_(2)and CO_(2)sensors for ambient conditions,that can be used in indoor air quality monitoring,breath analysis,food spoilage detection,etc.In the present study,two thin film nanocomposite(nickel oxide-graphene and nickel oxide-silver nanowires)gas sensors are fabricated using direct ink writing.The nano-composites are investigated for their structural,optical,and electrical properties.Later the nano-composite is deposited on the interdigitated electrode(IDE)pattern to form NO_(2)and CO_(2)sensors.The deposited films are then exposed to NO_(2)and CO_(2)gases separately and their response and recovery times are determined using a custom-built gas sensing setup.Nickel oxide-graphene provides a good response time and recovery time of 10 and 9 s,respectively for NO_(2),due to the higher electron affinity of graphene towards NO_(2).Nickel oxide-silver nanowire nano-composite is suited for CO_(2)gas because silver is an excellent electrocatalyst for CO_(2)by giving response and recovery times of 11 s each.This is the first report showcasing NiO nano-composites for NO_(2)and CO_(2)sensing at room temperature.展开更多
Inverted perovskite solar cells(PSCs)have stood out in recent years for their great potential in offering low-temperature compatibility,long-term stability and tandem cell suitability.However,challenges persist,partic...Inverted perovskite solar cells(PSCs)have stood out in recent years for their great potential in offering low-temperature compatibility,long-term stability and tandem cell suitability.However,challenges persist,particularly concerning the use of nickel oxide nanoparticles(NiO_(x)NPs)as the hole transport material,where issues such as low conductivity,impurity-induced aggregation and interface redox reactions significantly hinder device performance.In response,this study presents a novel synthesis method for NiO_(x)NPs,leveraging the introduction of ammonium salt dopants(NH_(4)Cl and NH_(4)SCN),and the solar cell utilizing the doped NiO_(x)substrate exhibits much enhanced device performance.Furthermore,doped solar cells reach 23.27%power conversion efficiency(PCE)when a self-assembled monolayer(SAM)is further employed.This study provides critical insights into the synthesis and growth pathways of NiO_(x)NPs,propelling the development of efficient hole transport materials for high-performance PSCs.展开更多
Li/Ni mixing negatively influences the discharge capacity of lithium nickel oxide and high-nickel ternary cathode materials.However,accurately measuring the Li/Ni mixing degree is difficult due to the preferred orient...Li/Ni mixing negatively influences the discharge capacity of lithium nickel oxide and high-nickel ternary cathode materials.However,accurately measuring the Li/Ni mixing degree is difficult due to the preferred orientation of labbased XRD measurements using Bragg–Brentano geometry.Here,we find that employing spherical harmonics in Rietveld refinement to eliminate the preferred orientation can significantly decrease the measurement error of the Li/Ni mixing ratio.The Li/Ni mixing ratio obtained from Rietveld refinement with spherical harmonics shows a strong correlation with discharge capacity,which means the electrochemical capacity of lithium nickel oxide and high-nickel ternary cathode can be estimated by the Li/Ni mixing degree.Our findings provide a simple and accurate method to estimate the Li/Ni mixing degree,which is valuable to the structural analysis and screening of the synthesis conditions of lithium nickel oxide and high-nickel ternary cathode materials.展开更多
To obtain the appropriate conditions for eliminating Fe3＋from NiSO4 solution, the digestion solution of the clinker was used as raw material, which was obtained from roasting the nickel oxide ore with （NH4）2SO4. Th...To obtain the appropriate conditions for eliminating Fe3＋from NiSO4 solution, the digestion solution of the clinker was used as raw material, which was obtained from roasting the nickel oxide ore with （NH4）2SO4. The ammonium jarosite was successfully synthesized from the solution with analytic grade NH4HCO3. The effects of reaction temperature, reaction time, end pH value of reaction on the removal rate of iron were investigated, and the effect of the initial concentration of Fe3＋was also discussed. All of those factors had significant effects on the removal rate of Fe3＋, among which the reaction temperature was the most prominent. The appropriate reaction conditions were concluded as follows： reaction temperature 95 ℃ reaction time 3.5 h, end pH value of reaction 2.5 at initial concentration of Fe3＋19.36 g/L. The physical aspect of （NH4）2Fe6（SO4）4（OH）12 was cluster figure composed of sheet or prismatic particles with smooth surface.展开更多
A nanocomposite of nickel oxide/carbon nanotubes was prepared through a simple chemical precipitation followed by thermal annealing. The electrochemical capacitance of this electrode material was studied. When the mas...A nanocomposite of nickel oxide/carbon nanotubes was prepared through a simple chemical precipitation followed by thermal annealing. The electrochemical capacitance of this electrode material was studied. When the mass fraction of CNTs (carbon nanotubes) in NiO/CNT composites increases, the electrical resistivity of nanocomposites decreases and becomes similar to that of pure CNTs when it reaches 30%. The specific surface area of composites increases with increasing CNT mass fraction and the specific capacitance reaches 160 F/g under 10 mA/g discharge current density at CNT mass fraction of 10%.展开更多
The emergence of inverted perovskite solar cells(PSCs) has attached great attention derived from the potential in improving stability. Charge transporting layer, especially hole transporting layer is crucial for effic...The emergence of inverted perovskite solar cells(PSCs) has attached great attention derived from the potential in improving stability. Charge transporting layer, especially hole transporting layer is crucial for efficient inverted PSCs. Organic materials were used as hole transporting layer previously. Recently, more and more inorganic hole transporting materials have been deployed for further improving the device stability. Nickel oxide(NiOx) as p-type metal oxide, owning high charge mobility and intrinsic stability,has been widely adopted in inverted PSCs. High performance over 20% efficiency has been achieved on NiOx base inverted PSCs. Herein, we have summarized recent progresses and strategies on the NiOx based PSCs, including the synthesis or deposition methods of NiOx, doping and surface modification of NiOx for efficient and stable PSCs. Finally, we will discuss current challenges of utilizing NiOx HTLs in PSCs and attempt to give probable solutions to make further development in efficient as well as stable NiOx based PSCs.展开更多
In this study, coral?like yolk–shell?structured NiO/C composite microspheres(denoted as CYS?NiO/C) were prepared using spray pyrolysis. The unique yolk–shell structure was characterized, and the formation mechanism ...In this study, coral?like yolk–shell?structured NiO/C composite microspheres(denoted as CYS?NiO/C) were prepared using spray pyrolysis. The unique yolk–shell structure was characterized, and the formation mechanism of the structure was proposed. Both the phase separation of the polyvinylpyrrolidone and polystyrene(PS) colloidal solution and the decompo?sition of the size?controlled PS nanobeads in the droplet played crucial roles in the formation of the unique coral?like yolk–shell structure. The CYS?NiO/C microspheres delivered a reversible discharge capacity of 991 mAh g^(-1) after 500 cycles at the current density of 1.0 A g^(-1). The dis?charge capacity of the CYS?NiO/C microspheres after the 1000 th cycle at the current density of 2.0 A g^(-1) was 635 mAh g^(-1), and the capacity retention measured from the second cycle was 91%. The final discharge capacities of the CYS?NiO/C microspheres at the current densities of 0.5, 1.5, 3.0, 5.0, 7.0, and 10.0 A g^(-1) were 753, 648, 560, 490, 440, and 389 mAh g^(-1), respectively. The synergetic e ect of the coral?like yolk–shell structure with well?defined interconnected mesopores and highly conductive carbon resulted in the excellent Li+?ion storage properties of the CYS?NiO/C microspheres.展开更多
The carbon and nickel oxide/carbon composite electrodes were prepared by plasma jet and magnetron sput-tering techniques. The investigations were performed to evaluate the influence of the Ar/C2H2 ratio on the specifi...The carbon and nickel oxide/carbon composite electrodes were prepared by plasma jet and magnetron sput-tering techniques. The investigations were performed to evaluate the influence of the Ar/C2H2 ratio on the specific capacitance values of carbon and NiO/carbon electrodes. The obtained electrodes were investigated by scanning electron microscopy, Raman scattering spectroscopy （RS）, and X-ray diffraction techniques. The surface of the carbon electrodes became less porous and more homogenous with increasing Ar/C2H2. The RS results indicated that the fraction of the sp2 carbon sites increased with increasing Ar/C2H2 ratio. The increase of the Ar/C2H2 ratio increased the capacitance values from 0.73 up to 3.8 F/g. Meanwhile, after the deposition of the nickel oxide on the carbon, the capacitance increased ten and more times and varied in the range of 7.6-86.1 F/g.展开更多
Semiconductor metal oxides have attracted wide attention in the area of gas sensor due to that they have unique advantages in the rapid and accurate detection of harmful gases.A simple strategy is to synthesize porous...Semiconductor metal oxides have attracted wide attention in the area of gas sensor due to that they have unique advantages in the rapid and accurate detection of harmful gases.A simple strategy is to synthesize porous NiO hollow microspheres via a simple hydrothermal method with trisodium citrate as structure guide agent is presented in this paper,and the shell of the microsphere is composed of porous and lamellar assembly units.The cavity proportion can be adjusted by changing the amount of trisodium citrate.A reasonable mechanism was proposed to explain the formation of porous NiO hollow microspheres.As a gas-sensing material,porous NiO hollow microspheres show excellent gas selectivity and rapid response recovery time for n-butyl alcohol gas.When the content of trisodium citrate was 0.10 g,the synthesized hollow sphere NiO had the highest response value(25.6)to 100×10^(-6) of n-butyl alcohol at 300℃ and the response and recovery times were only 68 and 10 s.展开更多
The preparation of Ni oxide films and their capacitive mechanism are discussed in this paper. Nickel oxide film electrodes perform pseudocapacitance in aqueous KOH and NaOH but perform double layer capacitance in LiCI...The preparation of Ni oxide films and their capacitive mechanism are discussed in this paper. Nickel oxide film electrodes perform pseudocapacitance in aqueous KOH and NaOH but perform double layer capacitance in LiCIO4/PC (propylence carbonate). The effect of increasing the specific capacitance was observed when Ni oxide film electrodes are doped with Co. A specific capacitance of around 70 F/g was achieved when using Ni oxide films doped with Co as electrodes and 1 mol/L aqueous KOH or NaOH as an electrolyte.展开更多
Thermal stability has long been recognized as a major limitation for the application of ligand modification in high-temperature reactions. Herein, we demonstrate polymeric phosphate as an efficient and stable ligand t...Thermal stability has long been recognized as a major limitation for the application of ligand modification in high-temperature reactions. Herein, we demonstrate polymeric phosphate as an efficient and stable ligand to tune the selectivity of propane oxidative dehydrogenation. Beneficial from the weakened affinity of propene, NiO modified with polymeric phosphate shows a selectivity 2–3 times higher than NiO towards the production of propene. The success of this regulation verifies the feasibility of ligand modification in high-temperature gas-phase reactions and shines a light on its applications in other important industrial reactions.展开更多
A new type of calcium-based regenerable carbon dioxide （CO_2） sorbent, CaO-NiO, was synthesized via the sol-gel method. The as synthesized CO_2 sorbent was in the form of nanoparticles. The CO_2 sorption temperature...A new type of calcium-based regenerable carbon dioxide （CO_2） sorbent, CaO-NiO, was synthesized via the sol-gel method. The as synthesized CO_2 sorbent was in the form of nanoparticles. The CO_2 sorption temperature and capacity of the sorbent were examined using thermogravi- metric analysis （TGA）. The CaO-NiO sorbent is able to capture CO_2 at a lower sorption temperature （465 ℃） than pure calcium oxide （CaO） （600 ℃）. The role of NiO in the CaO-NiO sorbent in lowering the CO_2 sorption temperature was also investigated. The sorbent was char- acterized by X-ray diffractometer （XRD）, N_2 adsorption-desorption analysis, high resolution transmission electron microscopy （HRTEM） and scanning electron microscopy （SEM）. CaO and NiO were found to coexist in the sorbent. Neither solid solution nor mixed metal oxide was formed. NiO did not react with CO_2 in the sorption process; but it worked like a catalyst to promote the CaO carbonation reaction. It is suggested that this new CaO-NiO sorbent may have a promising application as an effective CO_2 sorbent with lower energy consumption.展开更多
A new process for electrolytic production of a perfluorinated compound, （CF3）3N, using lanthanum nickel oxide-coated Ni sheet anode in the （CH3）4NF· 4.0HF melt at room temperature, was developed. Thin films o...A new process for electrolytic production of a perfluorinated compound, （CF3）3N, using lanthanum nickel oxide-coated Ni sheet anode in the （CH3）4NF· 4.0HF melt at room temperature, was developed. Thin films of the lanthanum nickel oxides were prepared on Ni sheets by sol-gel coating method using polyvinlylpyrrolidone（PVP）. The main components of the thin films were La2O3, LaNiO3, and La2NiO4 at 500, 750 and 1000℃, respectively. The anode performance in the （CH3）4NF·4.0HF melt depends greatly on the main component of the thin film, and the LaNiO3-coated Ni sheet anode gives the best anode performance. The potential of LaNiO3-coated Ni sheet anode remains constant at 5.9 V during electrolysis at 20 mA·cm^-2 in the （CH3）4NF·4.0HF melt for 100 h. This is because LaNiO3 and NiF3 and/or Ni2F5, the latter of which was formed during electrolysis, in the film give a high electronic conductivity to the surface film during electrolysis. The maximum mole fraction of （CF3）3N （21.4%） was obtained at 20 mA·cm^-2 in （CH3）4NF·4.0HF melt using the LaNiO3-coated Ni sheet.展开更多
The d-band state of materials is an important descriptor for activity of oxygen evolution reaction(OER).For NiO materials,there is rarely concern about tuning their d-band states to tailor the OER behaviors.Herein,NiO...The d-band state of materials is an important descriptor for activity of oxygen evolution reaction(OER).For NiO materials,there is rarely concern about tuning their d-band states to tailor the OER behaviors.Herein,NiO nanocrystals with doping small amount of La^(3+)were used to regulate d-band states for promoting OER activity.Density of states calculations based on density functional theory revealed that La^(3+)doping produced upper shift of d-band center,which would induce stronger electronic interaction between surface Ni atoms and species of oxygen evolution reaction intermediates.Further density functional theory calculation illustrated that La^(3+)doped NiO possessed reduced Gibbs free energy in adsorbing species of OER intermediate.Predicted by theoretical calculations,trace La^(3+)was introduced into crystal lattice of NiO nanoparticles.The La^(3+)doped NiO nanocrystal showed much promoted OER activity than corresponding pristine NiO product.Further electrochemical analysis revealed that La^(3+)doping into NiO increased the intrinsic activity such as improved active sites and reduced charge transfer resistance.The in-situ Raman spectra suggested that NiO phase in La^(3+)doped NiO could be better maintained than pristine NiO during the OER.This work provides an effective strategy to tune the d-band center of NiO for efficient electrocatalytic OER.展开更多
Nanosized nickel oxide powders were prepared by thermal decomposition of the nickel citrate gel precursors. The thermal decomposition and powder materials derived from calcination of these gel precursors with various ...Nanosized nickel oxide powders were prepared by thermal decomposition of the nickel citrate gel precursors. The thermal decomposition and powder materials derived from calcination of these gel precursors with various ratios of citric acid （CA） to nickel at different temperatures and times were characterized by thermal analysis （TG/DTA）, scanning electron microscopy （SEM）, x-ray diffraction （XRD）, and measurement of specific surface area （BET） with porosity analyses. The optimized processing conditions of calcination temperature 400℃ for 1 hour with the CA/Ni ratio of 1.2, were determined to produce the nanosized nickel oxide pow- ders with a high specific surface area of 181 m^2/g, nanometer particle sizes of 15-25 nm, micro-pore diameter distribution between 4-10 nm. The capacitance characteristics of the nanosized nickel oxide electrode in various concentrations of KOH solutions were studied by the cyclic voltammetry （CV） exhibiting both a double-layer capacitance and a faradaic pseudocapacitance. The nanosized nickel oxide electrode shows a high cyclic stability and is promising for high performance electrochemical capacitors.展开更多
In this study,we fabricated a NiOx film by electrodeposition of an ethanediamine nickel complex precursor(pH=11)on a fluorine‐doped tin oxide substrate.The resulting film is robust and exhibits high catalytic activit...In this study,we fabricated a NiOx film by electrodeposition of an ethanediamine nickel complex precursor(pH=11)on a fluorine‐doped tin oxide substrate.The resulting film is robust and exhibits high catalytic activity for electrochemical water oxidation.Water oxidation is initiated with an overpotential of375mV(1mA/cm2)and a steady current density of8.5mA/cm2is maintained for at least10h at1.3V versus the normal hydrogen electrode.Kinetic analysis reveals that there is a2e?/3H+pre‐equilibrium process before the chemical rate‐determining step.The low‐cost preparation,robustness,and longevity make this catalyst competitive for applications in solar energy conversion and storage.展开更多
A new sol-gel process for the preparation of ultrafine nickel hydroxideelectrode materials was developed. The composite electrodes consisting of carbon nanotubes andNi(OH)_2 were developed by mixing the hydroxide and ...A new sol-gel process for the preparation of ultrafine nickel hydroxideelectrode materials was developed. The composite electrodes consisting of carbon nanotubes andNi(OH)_2 were developed by mixing the hydroxide and carbon nanotubes together in different massratios. In order to enhance energy density, a combined type pseudocapacitor/electric double layercapacitor was considered and its electrochemical properties were characterized by cyclic voltammetryand dc charge/discharge test. The combined capacitor shows excellent capacitor behavior with anoperating voltage up to 1.6 V in KOH aqueous electrolyte. Stable charge/discharge behaviors wereobserved with much higher specific capacitance values of 24 F/g compared with that of EDLC (12 F/g)by introducing 60 percent Ni(0H)_2 in the anode material. By using the modified anode of aNi(OH)_2/carbon nanotubes composite electrode, the specific capacitance of the cell was lesssensitive to discharge current density compared with that of the capacitor employing pure nickelhydroxide as anode. The combined capacitor in this study exhibits high energy density and stablepower characteristics.展开更多
In order to study the effect of catalysts’morphology on the electrochemical reduction of nitrogen gas,sample catalysts of NiO with four different morphologies(hollow spherical,sea urchin-shape,cubic block,and rod-lik...In order to study the effect of catalysts’morphology on the electrochemical reduction of nitrogen gas,sample catalysts of NiO with four different morphologies(hollow spherical,sea urchin-shape,cubic block,and rod-like)were prepared.Characterization of the NiO catalysts was carried out using SEM,BET,XRD and electrochemical investigation techniques.The results indicated that the nitrogen reduction reaction(NRR)is strictly dependent on the morphology of the NiO catalysts,as the hollow spherical NiO showed the best electrochemical NRR performance of NH3 yield rate(3.21μg h^-1 mg^-1 cat.,4.1910^-11 mol cm^-2 s^-1)and Faradaic efficiency(1.37%),which was higher than the yields and efficiencies of the rod-NiO(1.8μg h^-1 mg^-1 cat.,3.2410^-11 mol cm^-2 s^-1,1.17%),sea urchin-NiO(1.66μg h^-1 mg^-1 cat.,2.4410^-11 mol cm^-2 s^-1,1.08%)and cubic block-NiO(1.32μg h^-1 mg^-1 cat.,2.1410^-11 mol cm^-2 s^-1,0.81%),respectively.These results match the order of the specific surface area of the NiO samples,with hollow spherical(113.91 m^2 g^-1)>rod-NiO(55.12 m^2 g^-1)sea urchin-NiO(55.29 m^2 g^-1)>cubic block-NiO(38.57 m^2 g^-1).This correlation can be attributed to the fact that large specific surface areas can provide more active sites for electrocatalysis.This work demonstrates the effect of the morphology of the NiO catalysts on its electrochemical NRR properties,which could offer some opportunity for the preparation of new electrode materials with improved electrocatalytic properties.展开更多
The triblock copolymer(PAA-b-PAN-b-PAA) iSs prepared by reversible addition-fragmentation chaintransfer polymerization,and then blended with polymer(PAN) and metal hydroxide(Ni(OH)2) as a precursor for heat-treatment....The triblock copolymer(PAA-b-PAN-b-PAA) iSs prepared by reversible addition-fragmentation chaintransfer polymerization,and then blended with polymer(PAN) and metal hydroxide(Ni(OH)2) as a precursor for heat-treatment.A composite material of hierarchical porous nanofibers and nickel oxide nanopa rticles(HPCF@NiO) is prepared by electrospinning combined with high-tempe rature carbonization.The effects of the ratio of PAA and PAA-b-PAN-b-PAA on the internal structure of nanofibers and their electrochemical properties as positive electrode materials are investigated.The experimental results show that when the ratio of PAA to PAA-b-PAN-b-PAA is 1.3 to 0.4,it has good pore structure and excellent electrochemical performance.At the current density of 1 A/g,the specific capacitance is 188.7 F/g and the potential window is -1 V to 0.37 V.The asymmetric supercapacitor assembled with activated carbon as the negative electrode materials has a specific capacitance of 21.2 F/g in 2 mol/L KOH and a capacitance retention of 85.7% after 12,500 cycles at different current density.展开更多
Quasi-one-dimensional NiO with a hierarchically porous structure was synthesized through a facile coordination−precipitation method with the coupling effect of ammonia and a post-calcination treatment.The electrocatal...Quasi-one-dimensional NiO with a hierarchically porous structure was synthesized through a facile coordination−precipitation method with the coupling effect of ammonia and a post-calcination treatment.The electrocatalytic properties of NiO fibers for the oxidation of ethanol were compared with those of NiO spheres.The results show that the fibrous NiO possesses a larger specific surface area of 140.153 m2/g and a lower electrical resistivity of 4.5×105Ω·m,leading to an impressively superior electrocatalytic activity to spherical NiO for ethanol oxidation in alkaline media.The current decay on fibrous NiO at 0.6 V in 100−900 s was 0.00003%,which is much lower than that of spherical NiO,indicating its better stability.The unique morphology and hierarchically porous structure give the fibrous NiO great potential to be used as an anodic electrocatalyst for direct ethanol fuel cells.展开更多
文摘The rapid industrial growth and increasing population have led to significant pollution and deterioration of the natural atmospheric environment.Major atmospheric pollutants include NO_(2)and CO_(2).Hence,it is imperative to develop NO_(2)and CO_(2)sensors for ambient conditions,that can be used in indoor air quality monitoring,breath analysis,food spoilage detection,etc.In the present study,two thin film nanocomposite(nickel oxide-graphene and nickel oxide-silver nanowires)gas sensors are fabricated using direct ink writing.The nano-composites are investigated for their structural,optical,and electrical properties.Later the nano-composite is deposited on the interdigitated electrode(IDE)pattern to form NO_(2)and CO_(2)sensors.The deposited films are then exposed to NO_(2)and CO_(2)gases separately and their response and recovery times are determined using a custom-built gas sensing setup.Nickel oxide-graphene provides a good response time and recovery time of 10 and 9 s,respectively for NO_(2),due to the higher electron affinity of graphene towards NO_(2).Nickel oxide-silver nanowire nano-composite is suited for CO_(2)gas because silver is an excellent electrocatalyst for CO_(2)by giving response and recovery times of 11 s each.This is the first report showcasing NiO nano-composites for NO_(2)and CO_(2)sensing at room temperature.
基金supported by the Open Research Fund of Songshan Lake Materials Laboratory(No.2021SLABFK09)the National Natural Science Foundation of China(No.22109093)+1 种基金the Program for Professor of Special Appointment(Eastern Scholar)at Shanghai Institutions of Higher Learning and the Shanghai Rising-Star Program(No.19QA1403800)the Project of Innovative Development Agency of Republic of Uzbekistan(No.FZ-20200929177)and Shanghai Technical Service Computing Center of Science and Engineering,Shanghai University.
文摘Inverted perovskite solar cells(PSCs)have stood out in recent years for their great potential in offering low-temperature compatibility,long-term stability and tandem cell suitability.However,challenges persist,particularly concerning the use of nickel oxide nanoparticles(NiO_(x)NPs)as the hole transport material,where issues such as low conductivity,impurity-induced aggregation and interface redox reactions significantly hinder device performance.In response,this study presents a novel synthesis method for NiO_(x)NPs,leveraging the introduction of ammonium salt dopants(NH_(4)Cl and NH_(4)SCN),and the solar cell utilizing the doped NiO_(x)substrate exhibits much enhanced device performance.Furthermore,doped solar cells reach 23.27%power conversion efficiency(PCE)when a self-assembled monolayer(SAM)is further employed.This study provides critical insights into the synthesis and growth pathways of NiO_(x)NPs,propelling the development of efficient hole transport materials for high-performance PSCs.
基金Project supported by the Natural Science Foundation of Beijing(Grant No.Z200013)the Beijing Municipal Science&Technology(Grant No.Z191100004719001)the National Natural Science Foundation of China(Grant Nos.52325207 and 22005333)。
文摘Li/Ni mixing negatively influences the discharge capacity of lithium nickel oxide and high-nickel ternary cathode materials.However,accurately measuring the Li/Ni mixing degree is difficult due to the preferred orientation of labbased XRD measurements using Bragg–Brentano geometry.Here,we find that employing spherical harmonics in Rietveld refinement to eliminate the preferred orientation can significantly decrease the measurement error of the Li/Ni mixing ratio.The Li/Ni mixing ratio obtained from Rietveld refinement with spherical harmonics shows a strong correlation with discharge capacity,which means the electrochemical capacity of lithium nickel oxide and high-nickel ternary cathode can be estimated by the Li/Ni mixing degree.Our findings provide a simple and accurate method to estimate the Li/Ni mixing degree,which is valuable to the structural analysis and screening of the synthesis conditions of lithium nickel oxide and high-nickel ternary cathode materials.
基金Project(51204054)supported by the National Natural Science Foundation of ChinaProject(N110402012)supported by Fundamental Research Funds for the Central Universities,ChinaProject(2007CB613603)supported by the National Basic Research Program of China
文摘To obtain the appropriate conditions for eliminating Fe3＋from NiSO4 solution, the digestion solution of the clinker was used as raw material, which was obtained from roasting the nickel oxide ore with （NH4）2SO4. The ammonium jarosite was successfully synthesized from the solution with analytic grade NH4HCO3. The effects of reaction temperature, reaction time, end pH value of reaction on the removal rate of iron were investigated, and the effect of the initial concentration of Fe3＋was also discussed. All of those factors had significant effects on the removal rate of Fe3＋, among which the reaction temperature was the most prominent. The appropriate reaction conditions were concluded as follows： reaction temperature 95 ℃ reaction time 3.5 h, end pH value of reaction 2.5 at initial concentration of Fe3＋19.36 g/L. The physical aspect of （NH4）2Fe6（SO4）4（OH）12 was cluster figure composed of sheet or prismatic particles with smooth surface.
基金This project was financially supported by the National Natural Science Foundation of China under grant No.50307009the Ministry of Science and Technology of South Korea through National Research Lab Program.
文摘A nanocomposite of nickel oxide/carbon nanotubes was prepared through a simple chemical precipitation followed by thermal annealing. The electrochemical capacitance of this electrode material was studied. When the mass fraction of CNTs (carbon nanotubes) in NiO/CNT composites increases, the electrical resistivity of nanocomposites decreases and becomes similar to that of pure CNTs when it reaches 30%. The specific surface area of composites increases with increasing CNT mass fraction and the specific capacitance reaches 160 F/g under 10 mA/g discharge current density at CNT mass fraction of 10%.
基金supported by the National Natural Science Foundation of China (Grant numbers: 61925405 and 51972102)。
文摘The emergence of inverted perovskite solar cells(PSCs) has attached great attention derived from the potential in improving stability. Charge transporting layer, especially hole transporting layer is crucial for efficient inverted PSCs. Organic materials were used as hole transporting layer previously. Recently, more and more inorganic hole transporting materials have been deployed for further improving the device stability. Nickel oxide(NiOx) as p-type metal oxide, owning high charge mobility and intrinsic stability,has been widely adopted in inverted PSCs. High performance over 20% efficiency has been achieved on NiOx base inverted PSCs. Herein, we have summarized recent progresses and strategies on the NiOx based PSCs, including the synthesis or deposition methods of NiOx, doping and surface modification of NiOx for efficient and stable PSCs. Finally, we will discuss current challenges of utilizing NiOx HTLs in PSCs and attempt to give probable solutions to make further development in efficient as well as stable NiOx based PSCs.
基金supported by the National Research Foundation of Korea (NRF) Grant funded by the Korea government (MSIP) (NRF-2018R1A4A1024691, NRF-2017M1A2A2087577, and NRF-2018R1D1A3B07042514)
文摘In this study, coral?like yolk–shell?structured NiO/C composite microspheres(denoted as CYS?NiO/C) were prepared using spray pyrolysis. The unique yolk–shell structure was characterized, and the formation mechanism of the structure was proposed. Both the phase separation of the polyvinylpyrrolidone and polystyrene(PS) colloidal solution and the decompo?sition of the size?controlled PS nanobeads in the droplet played crucial roles in the formation of the unique coral?like yolk–shell structure. The CYS?NiO/C microspheres delivered a reversible discharge capacity of 991 mAh g^(-1) after 500 cycles at the current density of 1.0 A g^(-1). The dis?charge capacity of the CYS?NiO/C microspheres after the 1000 th cycle at the current density of 2.0 A g^(-1) was 635 mAh g^(-1), and the capacity retention measured from the second cycle was 91%. The final discharge capacities of the CYS?NiO/C microspheres at the current densities of 0.5, 1.5, 3.0, 5.0, 7.0, and 10.0 A g^(-1) were 753, 648, 560, 490, 440, and 389 mAh g^(-1), respectively. The synergetic e ect of the coral?like yolk–shell structure with well?defined interconnected mesopores and highly conductive carbon resulted in the excellent Li+?ion storage properties of the CYS?NiO/C microspheres.
基金partly funded by the European Union (European Regional Development Fund) PlasTEP|# 033| KST 770123
文摘The carbon and nickel oxide/carbon composite electrodes were prepared by plasma jet and magnetron sput-tering techniques. The investigations were performed to evaluate the influence of the Ar/C2H2 ratio on the specific capacitance values of carbon and NiO/carbon electrodes. The obtained electrodes were investigated by scanning electron microscopy, Raman scattering spectroscopy （RS）, and X-ray diffraction techniques. The surface of the carbon electrodes became less porous and more homogenous with increasing Ar/C2H2. The RS results indicated that the fraction of the sp2 carbon sites increased with increasing Ar/C2H2 ratio. The increase of the Ar/C2H2 ratio increased the capacitance values from 0.73 up to 3.8 F/g. Meanwhile, after the deposition of the nickel oxide on the carbon, the capacitance increased ten and more times and varied in the range of 7.6-86.1 F/g.
基金financially supported by the Natural Science Basic Research Plan in Shaanxi Province of China(No.2018JM2015)the Fundamental Research Funds for the Central Universities(No.3102017jc01001)the National Key Research and Development Program of China(No.2017YFC0211500)。
文摘Semiconductor metal oxides have attracted wide attention in the area of gas sensor due to that they have unique advantages in the rapid and accurate detection of harmful gases.A simple strategy is to synthesize porous NiO hollow microspheres via a simple hydrothermal method with trisodium citrate as structure guide agent is presented in this paper,and the shell of the microsphere is composed of porous and lamellar assembly units.The cavity proportion can be adjusted by changing the amount of trisodium citrate.A reasonable mechanism was proposed to explain the formation of porous NiO hollow microspheres.As a gas-sensing material,porous NiO hollow microspheres show excellent gas selectivity and rapid response recovery time for n-butyl alcohol gas.When the content of trisodium citrate was 0.10 g,the synthesized hollow sphere NiO had the highest response value(25.6)to 100×10^(-6) of n-butyl alcohol at 300℃ and the response and recovery times were only 68 and 10 s.
基金The authors acknowledge the National Natural Science Foun-dation of China under grant number 50082001 for financial support.
文摘The preparation of Ni oxide films and their capacitive mechanism are discussed in this paper. Nickel oxide film electrodes perform pseudocapacitance in aqueous KOH and NaOH but perform double layer capacitance in LiCIO4/PC (propylence carbonate). The effect of increasing the specific capacitance was observed when Ni oxide film electrodes are doped with Co. A specific capacitance of around 70 F/g was achieved when using Ni oxide films doped with Co as electrodes and 1 mol/L aqueous KOH or NaOH as an electrolyte.
基金was supported by the National Natural Science Foundation of China(91545113,21703050)the China Postdoctoral Science Foundation(2017M610363,2018T110584)+2 种基金Shell Global Solutions International B.V.(PT71423,PT74557)the Fok Ying Tong Education Foundation(131015)the Science&Technology Program of Ningbo(2017C50014)~~
文摘Thermal stability has long been recognized as a major limitation for the application of ligand modification in high-temperature reactions. Herein, we demonstrate polymeric phosphate as an efficient and stable ligand to tune the selectivity of propane oxidative dehydrogenation. Beneficial from the weakened affinity of propene, NiO modified with polymeric phosphate shows a selectivity 2–3 times higher than NiO towards the production of propene. The success of this regulation verifies the feasibility of ligand modification in high-temperature gas-phase reactions and shines a light on its applications in other important industrial reactions.
基金supported by Long Term Research Grant(LRGS)(203/PKT/6723001) from Ministry of Higher Education(MOHE)Research University Team Grant(1001/PJKIMIA/854001) from University Sains MalaysiaPostgraduate Research Grant Scheme(PRGS) from University Sains Malaysia and USM Fellowship
文摘A new type of calcium-based regenerable carbon dioxide （CO_2） sorbent, CaO-NiO, was synthesized via the sol-gel method. The as synthesized CO_2 sorbent was in the form of nanoparticles. The CO_2 sorption temperature and capacity of the sorbent were examined using thermogravi- metric analysis （TGA）. The CaO-NiO sorbent is able to capture CO_2 at a lower sorption temperature （465 ℃） than pure calcium oxide （CaO） （600 ℃）. The role of NiO in the CaO-NiO sorbent in lowering the CO_2 sorption temperature was also investigated. The sorbent was char- acterized by X-ray diffractometer （XRD）, N_2 adsorption-desorption analysis, high resolution transmission electron microscopy （HRTEM） and scanning electron microscopy （SEM）. CaO and NiO were found to coexist in the sorbent. Neither solid solution nor mixed metal oxide was formed. NiO did not react with CO_2 in the sorption process; but it worked like a catalyst to promote the CaO carbonation reaction. It is suggested that this new CaO-NiO sorbent may have a promising application as an effective CO_2 sorbent with lower energy consumption.
文摘A new process for electrolytic production of a perfluorinated compound, （CF3）3N, using lanthanum nickel oxide-coated Ni sheet anode in the （CH3）4NF· 4.0HF melt at room temperature, was developed. Thin films of the lanthanum nickel oxides were prepared on Ni sheets by sol-gel coating method using polyvinlylpyrrolidone（PVP）. The main components of the thin films were La2O3, LaNiO3, and La2NiO4 at 500, 750 and 1000℃, respectively. The anode performance in the （CH3）4NF·4.0HF melt depends greatly on the main component of the thin film, and the LaNiO3-coated Ni sheet anode gives the best anode performance. The potential of LaNiO3-coated Ni sheet anode remains constant at 5.9 V during electrolysis at 20 mA·cm^-2 in the （CH3）4NF·4.0HF melt for 100 h. This is because LaNiO3 and NiF3 and/or Ni2F5, the latter of which was formed during electrolysis, in the film give a high electronic conductivity to the surface film during electrolysis. The maximum mole fraction of （CF3）3N （21.4%） was obtained at 20 mA·cm^-2 in （CH3）4NF·4.0HF melt using the LaNiO3-coated Ni sheet.
基金financial support from the National Natural Science Foundation of China(No.22072183)the Natural Science Foundation of Hunan Province,China(No.2022JJ30690)。
文摘The d-band state of materials is an important descriptor for activity of oxygen evolution reaction(OER).For NiO materials,there is rarely concern about tuning their d-band states to tailor the OER behaviors.Herein,NiO nanocrystals with doping small amount of La^(3+)were used to regulate d-band states for promoting OER activity.Density of states calculations based on density functional theory revealed that La^(3+)doping produced upper shift of d-band center,which would induce stronger electronic interaction between surface Ni atoms and species of oxygen evolution reaction intermediates.Further density functional theory calculation illustrated that La^(3+)doped NiO possessed reduced Gibbs free energy in adsorbing species of OER intermediate.Predicted by theoretical calculations,trace La^(3+)was introduced into crystal lattice of NiO nanoparticles.The La^(3+)doped NiO nanocrystal showed much promoted OER activity than corresponding pristine NiO product.Further electrochemical analysis revealed that La^(3+)doping into NiO increased the intrinsic activity such as improved active sites and reduced charge transfer resistance.The in-situ Raman spectra suggested that NiO phase in La^(3+)doped NiO could be better maintained than pristine NiO during the OER.This work provides an effective strategy to tune the d-band center of NiO for efficient electrocatalytic OER.
基金the National Natural Science Foundation of China(No.50134020)
文摘Nanosized nickel oxide powders were prepared by thermal decomposition of the nickel citrate gel precursors. The thermal decomposition and powder materials derived from calcination of these gel precursors with various ratios of citric acid （CA） to nickel at different temperatures and times were characterized by thermal analysis （TG/DTA）, scanning electron microscopy （SEM）, x-ray diffraction （XRD）, and measurement of specific surface area （BET） with porosity analyses. The optimized processing conditions of calcination temperature 400℃ for 1 hour with the CA/Ni ratio of 1.2, were determined to produce the nanosized nickel oxide pow- ders with a high specific surface area of 181 m^2/g, nanometer particle sizes of 15-25 nm, micro-pore diameter distribution between 4-10 nm. The capacitance characteristics of the nanosized nickel oxide electrode in various concentrations of KOH solutions were studied by the cyclic voltammetry （CV） exhibiting both a double-layer capacitance and a faradaic pseudocapacitance. The nanosized nickel oxide electrode shows a high cyclic stability and is promising for high performance electrochemical capacitors.
基金supported by the National Basic Research Program of China(973 program,2014CB239402)the National Natural Science Foundation of China(21476043)the Swedish Energy Agency and K&A Wallenberg Foundation~~
文摘In this study,we fabricated a NiOx film by electrodeposition of an ethanediamine nickel complex precursor(pH=11)on a fluorine‐doped tin oxide substrate.The resulting film is robust and exhibits high catalytic activity for electrochemical water oxidation.Water oxidation is initiated with an overpotential of375mV(1mA/cm2)and a steady current density of8.5mA/cm2is maintained for at least10h at1.3V versus the normal hydrogen electrode.Kinetic analysis reveals that there is a2e?/3H+pre‐equilibrium process before the chemical rate‐determining step.The low‐cost preparation,robustness,and longevity make this catalyst competitive for applications in solar energy conversion and storage.
文摘A new sol-gel process for the preparation of ultrafine nickel hydroxideelectrode materials was developed. The composite electrodes consisting of carbon nanotubes andNi(OH)_2 were developed by mixing the hydroxide and carbon nanotubes together in different massratios. In order to enhance energy density, a combined type pseudocapacitor/electric double layercapacitor was considered and its electrochemical properties were characterized by cyclic voltammetryand dc charge/discharge test. The combined capacitor shows excellent capacitor behavior with anoperating voltage up to 1.6 V in KOH aqueous electrolyte. Stable charge/discharge behaviors wereobserved with much higher specific capacitance values of 24 F/g compared with that of EDLC (12 F/g)by introducing 60 percent Ni(0H)_2 in the anode material. By using the modified anode of aNi(OH)_2/carbon nanotubes composite electrode, the specific capacitance of the cell was lesssensitive to discharge current density compared with that of the capacitor employing pure nickelhydroxide as anode. The combined capacitor in this study exhibits high energy density and stablepower characteristics.
基金The project was supported by the National Natural Science Foundation of China(NSFC,21703161).We thank Prof.Xingmao Jiang at Wuhan Institute of Technology for his assistance in collecting N2 adsorption-desorption isotherms data.
文摘In order to study the effect of catalysts’morphology on the electrochemical reduction of nitrogen gas,sample catalysts of NiO with four different morphologies(hollow spherical,sea urchin-shape,cubic block,and rod-like)were prepared.Characterization of the NiO catalysts was carried out using SEM,BET,XRD and electrochemical investigation techniques.The results indicated that the nitrogen reduction reaction(NRR)is strictly dependent on the morphology of the NiO catalysts,as the hollow spherical NiO showed the best electrochemical NRR performance of NH3 yield rate(3.21μg h^-1 mg^-1 cat.,4.1910^-11 mol cm^-2 s^-1)and Faradaic efficiency(1.37%),which was higher than the yields and efficiencies of the rod-NiO(1.8μg h^-1 mg^-1 cat.,3.2410^-11 mol cm^-2 s^-1,1.17%),sea urchin-NiO(1.66μg h^-1 mg^-1 cat.,2.4410^-11 mol cm^-2 s^-1,1.08%)and cubic block-NiO(1.32μg h^-1 mg^-1 cat.,2.1410^-11 mol cm^-2 s^-1,0.81%),respectively.These results match the order of the specific surface area of the NiO samples,with hollow spherical(113.91 m^2 g^-1)>rod-NiO(55.12 m^2 g^-1)sea urchin-NiO(55.29 m^2 g^-1)>cubic block-NiO(38.57 m^2 g^-1).This correlation can be attributed to the fact that large specific surface areas can provide more active sites for electrocatalysis.This work demonstrates the effect of the morphology of the NiO catalysts on its electrochemical NRR properties,which could offer some opportunity for the preparation of new electrode materials with improved electrocatalytic properties.
基金partly supported by the National Natural Science Foundation of China(No.51763014)the Program for Hongliu Distinguished Young Scholars in Lanzhou University of Technology(No.J201801)Joint fund between Shenyang National Laboratory for Materials Science and State Key Laboratory of Advanced Processing and Recycling of Nonferrous Metals(No.18LHPY002)。
文摘The triblock copolymer(PAA-b-PAN-b-PAA) iSs prepared by reversible addition-fragmentation chaintransfer polymerization,and then blended with polymer(PAN) and metal hydroxide(Ni(OH)2) as a precursor for heat-treatment.A composite material of hierarchical porous nanofibers and nickel oxide nanopa rticles(HPCF@NiO) is prepared by electrospinning combined with high-tempe rature carbonization.The effects of the ratio of PAA and PAA-b-PAN-b-PAA on the internal structure of nanofibers and their electrochemical properties as positive electrode materials are investigated.The experimental results show that when the ratio of PAA to PAA-b-PAN-b-PAA is 1.3 to 0.4,it has good pore structure and excellent electrochemical performance.At the current density of 1 A/g,the specific capacitance is 188.7 F/g and the potential window is -1 V to 0.37 V.The asymmetric supercapacitor assembled with activated carbon as the negative electrode materials has a specific capacitance of 21.2 F/g in 2 mol/L KOH and a capacitance retention of 85.7% after 12,500 cycles at different current density.
基金Project(51404306)supported by the National Natural Science Foundation of ChinaProject(JNJJ201613)supported by Jiana Foundation of Central South University,ChinaProject(2017YFC0210401)supported by the National Key Research and Development Program of China。
文摘Quasi-one-dimensional NiO with a hierarchically porous structure was synthesized through a facile coordination−precipitation method with the coupling effect of ammonia and a post-calcination treatment.The electrocatalytic properties of NiO fibers for the oxidation of ethanol were compared with those of NiO spheres.The results show that the fibrous NiO possesses a larger specific surface area of 140.153 m2/g and a lower electrical resistivity of 4.5×105Ω·m,leading to an impressively superior electrocatalytic activity to spherical NiO for ethanol oxidation in alkaline media.The current decay on fibrous NiO at 0.6 V in 100−900 s was 0.00003%,which is much lower than that of spherical NiO,indicating its better stability.The unique morphology and hierarchically porous structure give the fibrous NiO great potential to be used as an anodic electrocatalyst for direct ethanol fuel cells.
