NiO-La0.3Ce0.7O2-δ(LDC30) novel anode was investigated for IT-SOFCs(Intermediate Temperature-Solid Oxide Fuel Cells) with LaGaO3-based electrolyte. The results showed that LDC30 has a suitable chemical compatibility ...NiO-La0.3Ce0.7O2-δ(LDC30) novel anode was investigated for IT-SOFCs(Intermediate Temperature-Solid Oxide Fuel Cells) with LaGaO3-based electrolyte. The results showed that LDC30 has a suitable chemical compatibility with NiO and NiO-LDC30 has a good thermal expansion matching with LDC30 interlayer and LSGM(La0.8Sr0.2Ga0.8Mg0.2O3-δ) electrolyte, so NiO-LDC30/LDC30 was considered as a feasible and novel anode system. It was also shown that NiO content plays a key role on polarization performance and morphology of the anode. When the content of NiO was 60%(mass fraction), the polarization loss of anode was the lowest. Next we will optimize the porosity and sintering procedure to modify the microstructure and performance of the anode.展开更多
Layered F-doped cathode materials 0.3 Li_2 MnO_3-0.7 LiMn_(1/3)Ni_(1/3)CO_(1/3))O_(2-x)F_x(x = 0, 0.01, 0.02, 0.03, 0.04,0.05) microspheres made up of nanosized primary grains were prepared through co-precipitation me...Layered F-doped cathode materials 0.3 Li_2 MnO_3-0.7 LiMn_(1/3)Ni_(1/3)CO_(1/3))O_(2-x)F_x(x = 0, 0.01, 0.02, 0.03, 0.04,0.05) microspheres made up of nanosized primary grains were prepared through co-precipitation method. The sample of x = 0.02 demonstrates a large discharge capacity of226 mAh g^(-1) over 100 cycles at 0.1 C and excellent rate performance with discharge capacity of 96 mAh g-1 at 5.0 C and room temperature. Particularly, this material shows much enhanced electrochemical performances even at high temperature of 55 ℃. It delivers a quite high discharge capacity of 233.7 mAh·g^(-1) at 1.0 C with capacity retention as high as 97.9% after 100 cycles. The results demonstrate that the fluorine incorporation stabilizes the cathode structure and maintains stable interfacial resistances.展开更多
Thermoelectric properties of Li-doped Sr0.70Ba0.30Nb2O6-δ ceramics were investigated in the temperature range from 323 K to 1073 K. The electrical conductivity increases significantly after lithium interstitial dopin...Thermoelectric properties of Li-doped Sr0.70Ba0.30Nb2O6-δ ceramics were investigated in the temperature range from 323 K to 1073 K. The electrical conductivity increases significantly after lithium interstitial doping. However, both of the magnitudes of Seebeck coefficient and electrical conductivity vary non-monotonically but synchronously with the doping contents, indicating that doped lithium ions may not be fully ionized and oxygen vacancy may also contribute to carriers. The lattice thermal conductivity increases firstly and then decreases as the doping content increases, which is affected by competing factors.Thermoelectric performance is enhanced by lithium interstitial doping due to the increase of the power factor and the thermoelectric figure of merit reaches maximum value （0.21 at 1073 K） in the sample Sr0.70Ba0.30Li0.10Nb2O6.展开更多
Sm_2(Zr_(0.7)Ce_(0.3))_2O_7是一种三元稀土氧化物材料,具有耐腐蚀性能好、熔点高、热导率低、热稳定性良好等优点,在热障涂层领域有着潜在的应用前景.以Sm_2O_3,ZrOCl_2·8H_2O和Ce(NO_3)3·6H_2O为原材料,通过水热合成法制备...Sm_2(Zr_(0.7)Ce_(0.3))_2O_7是一种三元稀土氧化物材料,具有耐腐蚀性能好、熔点高、热导率低、热稳定性良好等优点,在热障涂层领域有着潜在的应用前景.以Sm_2O_3,ZrOCl_2·8H_2O和Ce(NO_3)3·6H_2O为原材料,通过水热合成法制备了Sm_2(Zr_(0.7)Ce_(0.3))_2O_7是纳米材料,并与同样方法制备的Sm_2Zr_2O_7的相关性能进行了对比.通过TG-DSC、XRD、Raman、SEM等测试手段对材料的热行为、相结构、晶粒尺寸和形貌等参数进行了表征.结果表明:Sm_2(Zr_(0.7)Ce_(0.3))_2O_7纳米材料在高温热处理后为烧绿石结构,初始样品的晶粒尺寸为5.43 nm,比表面积为103.11 m2g^(-1).同时对热导率、热膨胀系数等热物性能进行了研究,其热导率为1.04 W m^(-1)K^(-1),热膨胀系数为10.86×10^(-6)K^(-1),这些性能均满足热障涂层的标准.与Sm_2Zr_2O_7相比,Sm_2(Zr_(0.7)Ce_(0.3))_2O_7具有更优异的性能,是一种具有广泛应用前景的纳米热障涂层材料.展开更多
The Ce0.7Zr0.3O2 solid solution and CeO2 were prepared using the sol-gel method. The phase structure, crystallite sizes and the reducibility of the catalysts were characterized by XRD and H2-TPR techniques. XRD result...The Ce0.7Zr0.3O2 solid solution and CeO2 were prepared using the sol-gel method. The phase structure, crystallite sizes and the reducibility of the catalysts were characterized by XRD and H2-TPR techniques. XRD results indicated that Zr^4＋ had replaced part of Ce^4＋ to form a fluorite-like solid solution, which was favorable to obtain ultrafine nanoparticles. The ratio of main HE consumption for Ce0.7Zr0.3O2：CeO2 was 4.4：1.0, implying that the solid solution could improve the reducibility compared to the single CeO2. The Ce0.7Zr0.3O2 solid solution catalyst showed a sharp combustion peak at 397 ℃, which was 200 ℃ lower than that of the single soot. The good catalytic activity of the Ce0.7Zr0.3O2 was attributed to the formation of nano-CeO2-based solid solution, which enhanced the reducibility and then improved the combustion activity. As Ce0.7Zr0.3O2 could be easily reduced to Ce0.7Zr0.3O2-x meanwhile, after oxygenation, the Ce0.7Zr0.3O2.x was recovered to Ce0.7Zr0.3O2 completely. A catalytic combustion reaction mechanism was proposed： the Ce0.7Zr0.3O2 was reduced to Ce0.7Zr0.3O2-x by the reaction with carbon and then it was recovered to Ce0.7Zr0.3O2-x by the interaction with O2.展开更多
La0.15Sr0.85Ga0.3Fe0.7O3-δ (LSGFO) and La0.15Sr0.85Co0.3Fe0.7O3-δ (LSCFO) mixed oxygenion and electron conducting oxides were synthesized by using a combined EDTA and citrate complexing method, and the corresponding...La0.15Sr0.85Ga0.3Fe0.7O3-δ (LSGFO) and La0.15Sr0.85Co0.3Fe0.7O3-δ (LSCFO) mixed oxygenion and electron conducting oxides were synthesized by using a combined EDTA and citrate complexing method, and the corresponding dense membranes were fabricated. The properties of the oxide powders and membranes were characterized with combined SEM, XRD, H2-TPR, O2-TPD techniques, mechanical strength and oxygen permeation measurement. The results showed that LSGFO had much higher thermochemical stability than LSCFO due to the higher valence stability of Ga3+. After the temperature-programmed reduction by 5% H2 in Ar from 20°C to 1020°C, the basic perovskite structure of LSGFO was successfully preserved. LSGFO also favors the oxygen vacancy formation better than LSCFO. Oxygen permeation measurement demonstrated that LSGFO had higher oxygen permeation flux than LSCFO, but they had similar activation energy for oxygen transportation, with a value of 110 and 117 kJ · mol-1, respectively. The difference in oxygen permeation fluxes was correlated with the difference in oxygen vacancy concentrations for the two materials.展开更多
文摘NiO-La0.3Ce0.7O2-δ(LDC30) novel anode was investigated for IT-SOFCs(Intermediate Temperature-Solid Oxide Fuel Cells) with LaGaO3-based electrolyte. The results showed that LDC30 has a suitable chemical compatibility with NiO and NiO-LDC30 has a good thermal expansion matching with LDC30 interlayer and LSGM(La0.8Sr0.2Ga0.8Mg0.2O3-δ) electrolyte, so NiO-LDC30/LDC30 was considered as a feasible and novel anode system. It was also shown that NiO content plays a key role on polarization performance and morphology of the anode. When the content of NiO was 60%(mass fraction), the polarization loss of anode was the lowest. Next we will optimize the porosity and sintering procedure to modify the microstructure and performance of the anode.
基金financially supported by the National Natural Science Foundation of China (No. 51372136)the NSFC-Guangdong United Fund (No. U1401246)
文摘Layered F-doped cathode materials 0.3 Li_2 MnO_3-0.7 LiMn_(1/3)Ni_(1/3)CO_(1/3))O_(2-x)F_x(x = 0, 0.01, 0.02, 0.03, 0.04,0.05) microspheres made up of nanosized primary grains were prepared through co-precipitation method. The sample of x = 0.02 demonstrates a large discharge capacity of226 mAh g^(-1) over 100 cycles at 0.1 C and excellent rate performance with discharge capacity of 96 mAh g-1 at 5.0 C and room temperature. Particularly, this material shows much enhanced electrochemical performances even at high temperature of 55 ℃. It delivers a quite high discharge capacity of 233.7 mAh·g^(-1) at 1.0 C with capacity retention as high as 97.9% after 100 cycles. The results demonstrate that the fluorine incorporation stabilizes the cathode structure and maintains stable interfacial resistances.
基金supported by the National Basic Research Program of China(Grant No.2013CB632506)the National Natural Science Foundation of China(Grant Nos.51202132,51231007,and 11374186)
文摘Thermoelectric properties of Li-doped Sr0.70Ba0.30Nb2O6-δ ceramics were investigated in the temperature range from 323 K to 1073 K. The electrical conductivity increases significantly after lithium interstitial doping. However, both of the magnitudes of Seebeck coefficient and electrical conductivity vary non-monotonically but synchronously with the doping contents, indicating that doped lithium ions may not be fully ionized and oxygen vacancy may also contribute to carriers. The lattice thermal conductivity increases firstly and then decreases as the doping content increases, which is affected by competing factors.Thermoelectric performance is enhanced by lithium interstitial doping due to the increase of the power factor and the thermoelectric figure of merit reaches maximum value （0.21 at 1073 K） in the sample Sr0.70Ba0.30Li0.10Nb2O6.
文摘Sm_2(Zr_(0.7)Ce_(0.3))_2O_7是一种三元稀土氧化物材料,具有耐腐蚀性能好、熔点高、热导率低、热稳定性良好等优点,在热障涂层领域有着潜在的应用前景.以Sm_2O_3,ZrOCl_2·8H_2O和Ce(NO_3)3·6H_2O为原材料,通过水热合成法制备了Sm_2(Zr_(0.7)Ce_(0.3))_2O_7是纳米材料,并与同样方法制备的Sm_2Zr_2O_7的相关性能进行了对比.通过TG-DSC、XRD、Raman、SEM等测试手段对材料的热行为、相结构、晶粒尺寸和形貌等参数进行了表征.结果表明:Sm_2(Zr_(0.7)Ce_(0.3))_2O_7纳米材料在高温热处理后为烧绿石结构,初始样品的晶粒尺寸为5.43 nm,比表面积为103.11 m2g^(-1).同时对热导率、热膨胀系数等热物性能进行了研究,其热导率为1.04 W m^(-1)K^(-1),热膨胀系数为10.86×10^(-6)K^(-1),这些性能均满足热障涂层的标准.与Sm_2Zr_2O_7相比,Sm_2(Zr_(0.7)Ce_(0.3))_2O_7具有更优异的性能,是一种具有广泛应用前景的纳米热障涂层材料.
基金the Natural Science Foundation of Zhejiang Province (Z404383)
文摘The Ce0.7Zr0.3O2 solid solution and CeO2 were prepared using the sol-gel method. The phase structure, crystallite sizes and the reducibility of the catalysts were characterized by XRD and H2-TPR techniques. XRD results indicated that Zr^4＋ had replaced part of Ce^4＋ to form a fluorite-like solid solution, which was favorable to obtain ultrafine nanoparticles. The ratio of main HE consumption for Ce0.7Zr0.3O2：CeO2 was 4.4：1.0, implying that the solid solution could improve the reducibility compared to the single CeO2. The Ce0.7Zr0.3O2 solid solution catalyst showed a sharp combustion peak at 397 ℃, which was 200 ℃ lower than that of the single soot. The good catalytic activity of the Ce0.7Zr0.3O2 was attributed to the formation of nano-CeO2-based solid solution, which enhanced the reducibility and then improved the combustion activity. As Ce0.7Zr0.3O2 could be easily reduced to Ce0.7Zr0.3O2-x meanwhile, after oxygenation, the Ce0.7Zr0.3O2.x was recovered to Ce0.7Zr0.3O2 completely. A catalytic combustion reaction mechanism was proposed： the Ce0.7Zr0.3O2 was reduced to Ce0.7Zr0.3O2-x by the reaction with carbon and then it was recovered to Ce0.7Zr0.3O2-x by the interaction with O2.
基金Acknowledgements This work was supported by the National Natural Science Foundation of China (Grant No. 59789201), the National Advanced Materials Committee of China (Grant No. 715-006-0122) and the Ministry of Science and Technology, China (Grant No. G1
文摘La0.15Sr0.85Ga0.3Fe0.7O3-δ (LSGFO) and La0.15Sr0.85Co0.3Fe0.7O3-δ (LSCFO) mixed oxygenion and electron conducting oxides were synthesized by using a combined EDTA and citrate complexing method, and the corresponding dense membranes were fabricated. The properties of the oxide powders and membranes were characterized with combined SEM, XRD, H2-TPR, O2-TPD techniques, mechanical strength and oxygen permeation measurement. The results showed that LSGFO had much higher thermochemical stability than LSCFO due to the higher valence stability of Ga3+. After the temperature-programmed reduction by 5% H2 in Ar from 20°C to 1020°C, the basic perovskite structure of LSGFO was successfully preserved. LSGFO also favors the oxygen vacancy formation better than LSCFO. Oxygen permeation measurement demonstrated that LSGFO had higher oxygen permeation flux than LSCFO, but they had similar activation energy for oxygen transportation, with a value of 110 and 117 kJ · mol-1, respectively. The difference in oxygen permeation fluxes was correlated with the difference in oxygen vacancy concentrations for the two materials.
