Hanyu Xu 1,Xuedan Song 1,*,Qing Zhang 1,Chang Yu 1,Jieshan Qiu 1,2,*1 Liaoning Key Lab for Energy Materials and Chemical Engineering,State Key Laboratory of Fine Chemicals,School of Chemical Engineering,Dalian Univers...Hanyu Xu 1,Xuedan Song 1,*,Qing Zhang 1,Chang Yu 1,Jieshan Qiu 1,2,*1 Liaoning Key Lab for Energy Materials and Chemical Engineering,State Key Laboratory of Fine Chemicals,School of Chemical Engineering,Dalian University of Technology,Dalian 116024,Liaoning Province,China.展开更多
Copolymerization of styrene (St) with N-phenylmaleimide (NPMI) was studied with rare earth coordination catalyst Nd(naph)3-AlEt3 in toluene. Characterization of the copolymers showed that the copolymers possess an al...Copolymerization of styrene (St) with N-phenylmaleimide (NPMI) was studied with rare earth coordination catalyst Nd(naph)3-AlEt3 in toluene. Characterization of the copolymers showed that the copolymers possess an alternating structure.展开更多
The catalysts were prepared by the temperature programmed reaction (TPR) of MoO3 with NH3 at various temperatures in the range of 573K～973K, and their hydrodenitrogenation (HDN) activities were tested in situ.It is s...The catalysts were prepared by the temperature programmed reaction (TPR) of MoO3 with NH3 at various temperatures in the range of 573K～973K, and their hydrodenitrogenation (HDN) activities were tested in situ.It is shown that molybdenum nitrid(Mo2N) was formed above 923K and its intermediate MoO2 formed at about 573～623K under the rapid (5K/min.) TPR conditions.Mo2N is the most active species for pyridine HDN among MoO3,MoO2,MoS2,and Mo2N. Moreover,it can be promoted by adding Ni component.It is shown that the Ni/Mo2N catalyst prepared by adding some NiO into the precursor MoO3 has a steady HDN activity Which is far higher than that of the commercial sulfided NiMo/Al2O3(HR346) catalyst.展开更多
Selective catalytic reduction technology using NH3 as a reducing agent（NH3-SCR） is an effective control method to remove nitrogen oxides. TiO2-supported vanadium oxide catalysts with different levels of Ce and Sb mo...Selective catalytic reduction technology using NH3 as a reducing agent（NH3-SCR） is an effective control method to remove nitrogen oxides. TiO2-supported vanadium oxide catalysts with different levels of Ce and Sb modification were prepared by an impregnation method and were characterized by X-ray diffractometer（XRD）, Brunauer-Emmett-Teller（BET）, Transmission electron microscopy（TEM）, Fourier transform infrared spectroscopy（FT-IR）, UV-Vis diffuse reflectance spectroscopy（UV-Vis DRS）, Raman and Hydrogen temperature-programmed reduction（H2-TPR）. The catalytic activities of V5 CexS by/TiO2 catalysts for denitration were investigated in a fixed bed flow microreactor. The results showed that cerium, vanadium and antimony oxide as the active components were well dispersed on TiO2, and the catalysts exhibited a large number of d-d electronic transitions, which were helpful to strengthen SCR reactivity. The V5 CexS by/TiO2 catalysts exhibited a good low temperature NH3-SCR catalytic activity. In the temperature range of 210 to 400℃, the V5 CexS by/TiO2 catalysts gave NO conversion rates above 90%. For the best V5Ce35Sb2/TiO2 catalyst, at a reaction temperature of 210℃, the NO conversion rate had already reached 90%. The catalysts had different catalytic activity with different Ce loadings. With the increase of Ce loading, the NO conversion rate also increased.展开更多
A novel three-dimensional (3D) layered MoS2@graphene functionalized with nitrogen-doped graphene quantum dots (MoS2@N-GQDs-GR) composites as an enhanced electrochemical hydrogen evolution catalyst. The few layered MoS...A novel three-dimensional (3D) layered MoS2@graphene functionalized with nitrogen-doped graphene quantum dots (MoS2@N-GQDs-GR) composites as an enhanced electrochemical hydrogen evolution catalyst. The few layered MoS2 nanoflowers supported on N-GQDs-GR surface were elaborately fabricated by one-pot hydrothermal method, which MoS2 and N-GQDs-GR exist in a bonding manner of Mo-N. In addition, due to the layered MoS2 sheet edge exposes more hydrogen evolution active sites and N-GQDs-GR have high conductivity, the composites exhibit prominent electrocatalytic activity with a low overpotential 99 mV, a small Tafel slope 49.3 mV/dec. Therefore, that the current work will develop HER catalysts may replace Pt.展开更多
An efficient and versatile practical protocol for the chemoselective N-tert-butoxycarbonylation of amines using Nano-γ-Fe2O3 and (BOC)2O. Nano-γ-Fe2O3 was applied as an efficient, green, heterogeneous and reusable c...An efficient and versatile practical protocol for the chemoselective N-tert-butoxycarbonylation of amines using Nano-γ-Fe2O3 and (BOC)2O. Nano-γ-Fe2O3 was applied as an efficient, green, heterogeneous and reusable catalyst at ambient temperature;the method is general for the preparation of N-Boc derivatives of aliphatic, heterocyclic, aromatic as well as amino acid derivatives.展开更多
The effects of the substituents on the cyclopentadienyl ring and the reducing agents on the catalytic activity and the stability of titanocene/NaH or n BuLi systems for the hydrogenation of olefins were investiga...The effects of the substituents on the cyclopentadienyl ring and the reducing agents on the catalytic activity and the stability of titanocene/NaH or n BuLi systems for the hydrogenation of olefins were investigated. For the catalyst systems composed of titanocene/NaH or n BuLi, the nature and the number of the substituents on the cyclopentadienyl ring control the catalytic behavior of those two systems. The effect of the reducing agent on the catalytic activity is relatively small. In addition, the characters of the hydrogenation of various olefins catalyzed respectively by Cp 2TiCl 2/NaH or n BuLi systems were compared.展开更多
An environmentally friendly precursor, adenosine, has been used as a dual source of C and N to synthesize nitrogen-doped carbon catalyst with/without Fe. A hydrothermal carbonization method has been used and water is ...An environmentally friendly precursor, adenosine, has been used as a dual source of C and N to synthesize nitrogen-doped carbon catalyst with/without Fe. A hydrothermal carbonization method has been used and water is the carbonization media. The morphology of samples with/without Fe component has been compared by HRTEM, and the result shows that Fe can promote the graphitization of carbon. Further electro-chemical test shows that the oxygen reduction reaction（ORR） catalytic activity of Fe-containing sample（C–Fe N） is much higher than that of the Fe-free sample（C–N）. Additionally, the intermediates of C–Fe N formed during each synthetic procedure have been thoroughly characterized by multiple methods,and the function of each procedure has been discussed. The C–Fe N sample exhibits high electro-catalytic stability and superior electro-catalytic activity toward ORR in alkaline media, with its half-wave potential 20 mV lower than that of commercial Pt/C（40 wt%）. It is further incorporated into alkaline polymer electrolyte fuel cell（APEFC） as the cathode material and led to a power density of 100 m W/cm;.展开更多
CePO4 （in particular, monoclinic CePO4） has been rarely used to make supported catalysts. Herein, monoclinic CeP04 nanoparticles were prepared by calcining hexagonal CePO4 nanomds （prepared by precipitation） in ai...CePO4 （in particular, monoclinic CePO4） has been rarely used to make supported catalysts. Herein, monoclinic CeP04 nanoparticles were prepared by calcining hexagonal CePO4 nanomds （prepared by precipitation） in air at 900 ℃. Monoclinic CePO4 nanowires were prepared by calcining hexagonal CePO4 nanowires （prepared by hydrothermal synthesis at 150 ℃） in air at 900 ℃. Both monoclinic CePO4 materials were used to support Rh2O3 by impregnation using Rh（NO3）3 as a precursor （followed by calcination）. The catalytic performance of Rh2O3/monoclinic CePO4 composite materials in N2O decomposition and CO oxidation was investigated. It was found that Rh2O3 supported on monoclinic CePO4 nanowims was much more active than Rh2O3 supported on monoclinic CePO4 nanoparticles. The stability of catalysts as a function of reaction time on stream was studied in both reactions. The influence of co-fed CO2, O2, and H2O on the catalytic activity in N20 decomposition was also studied. These catalysts were characterized by employing N2 adsorption-desorption, ICP-OES, XRD, TEM, XPS, H2-TPR, O2-TPD, and CO2-TPD. The correlation between physicochemical properties and catalytic properties was discussed.展开更多
Ni-based catalysts supported by γ-Al_2O_3 were prepared for improving the lower heating value( LHV) of biomass gasification fuel gas through methanation. Prior to the performance tests, the physico-chemical propertie...Ni-based catalysts supported by γ-Al_2O_3 were prepared for improving the lower heating value( LHV) of biomass gasification fuel gas through methanation. Prior to the performance tests, the physico-chemical properties of the catalyst samples were characterized by N_2 isothermal adsorption/desorption, X-ray diffraction( XRD) and a scanning electron microscope( SEM). Afterwards, a series of experiments were carried out to investigate the catalytic performance and the results showthat catalysts with 15% and20% Ni loadings have better methanation catalytic effect than those with 5% and 10% Ni loadings in terms of elevating the LHV of biomass gasification fuel gas. M oreover, controllable influential factors such as the reaction temperature, the H_2/CO ratio and the water content occupy an important position in the methanation of biomass gasification fuel gas. 15 Ni/γ-Al_2O_3 and 20 Ni/γ-Al_2O_3 catalysts have a higher CO conversion and CH_4 selectivity at 350 ℃ and the LHV of biomass gasification fuel gas can be largely increased by 34. 3 % at 350 ℃. Higher H_2/CO ratio and a lower water content are more beneficial for improving the LHV of biomass gasification fuel gas when considering the combination of both CO conversion and CH_4 selectivity. This is due to the fact that a higher H_2/CO ratio and lower water content can increase the extent of the methanation reaction.展开更多
Proton exchange membrane fuel cells(PEMFC)have attracted much attention because of their high energy conversion efficiency,high power density and zero emission of pollutants.However,the high cost of the cathode platin...Proton exchange membrane fuel cells(PEMFC)have attracted much attention because of their high energy conversion efficiency,high power density and zero emission of pollutants.However,the high cost of the cathode platinum group metal(PGM)catalysts creates a barrier for the large-scale application of PEMFC.Tremendous efforts have been devoted to the development of low-cost PGM-free catalysts,especially the Fe-N-C catalysts,to replace the expensive PGM catalysts.However,the characterization methods and evaluation standards of the catalysts varies,which is not conducive to the comparison of PGM-free catalysts.U.S.Department of energy(DOE)is the only authority that specifies the testing standards and activity targets for PGM-free catalysts.In this review,the major breakthroughs of Fe-N-C catalysts are outlined with the reference of DOE standards and targets.The preparation and characteristics of these highly active Fe-N-C catalysts are briefly introduced.Moreover,the efforts on improving the mass transfer and the durability issue of Fe-N-C fuel cell are discussed.Finally,the prospective directions concerning the comprehensive evaluation of the Fe-N-C catalysts are proposed.展开更多
Atomically dispersed iron-nitrogen-carbon(Fe-N-C) catalysts have emerged as the most promising alternative to the expensive Pt-based catalysts for the oxygen reduction reaction(ORR) in proton exchange membrane fuel ce...Atomically dispersed iron-nitrogen-carbon(Fe-N-C) catalysts have emerged as the most promising alternative to the expensive Pt-based catalysts for the oxygen reduction reaction(ORR) in proton exchange membrane fuel cells(PEMFCs),however suffer from low site density of active Fe-N4 moiety and limited mass transport during the catalytic reaction.To address these challenges,we report a three-dimensional(3D) metal-organic frameworks(MOF)-derived Fe-N-C single-atom catalyst.In this well-designed Fe-N-C catalyst,the micro-scale interconnected skeleton,the nano-scale ordered pores and the atomic-scale abundant carbon edge defects inside the skeleton significantly enhance the site density of active Fe-N4 moiety,thus improving the Fe utilization in the final catalyst.Moreover,the combination of the above mentioned micro-and nano-scale structures greatly facilitates the mass transport in the 3D Fe-N-C catalyst.Therefore,the multiscale engineered Fe-N-C single-atom catalyst achieves excellent ORR performance under acidic condition and affords a significantly enhanced current density and power density in PEMFC.Our findings may open new opportunities for the rational design of FeN-C catalysts through multiscale structural engineering.展开更多
Hydroisomerization catalysts Pt/ZSM-22, Pt/ZSM-23, and Pt/ZSM-22/ZSM-23 were prepared by supporting Pt on ZSM-22, ZSM-23, and intergrowth zeolite ZSM-22/ZSM-23, respectively. The typical physicochemical properties of ...Hydroisomerization catalysts Pt/ZSM-22, Pt/ZSM-23, and Pt/ZSM-22/ZSM-23 were prepared by supporting Pt on ZSM-22, ZSM-23, and intergrowth zeolite ZSM-22/ZSM-23, respectively. The typical physicochemical properties of these catalysts were characterized by X-Ray Diffraction （XRD）, N2 absorption-desorption, Pyridine-Fourier Transform Infrared （Py-FTIR）, Transmission Electron Microscopy （TEM）, X-Ray Fluorescence （XRF）, Scanning Electron Microscopy （SEM） and NH3- Temperature Programmed Desorption （NH3-TPD）, and the performance of these catalysts in n-dodecane hydroisomerization was evaluated in a continuous down-flow fixed bed with a stainless steel tubular reactor. The characterization results indicated that the intergrowth zeolite ZSM-22/ZSM-23 possessed the dual structure of ZSM-22 and ZSM-23, and the catalyst Pt/ZSM-22/ZSM-23 had similar pores and weak acidity to Pt/ZSM-22 and Pt/ZSM-23 catalysts. Moreover, Pt/ZSM-22/ZSM-23 catalyst showed a high selectivity in hydroisomerization of long chain n-alkanes to mono-branched isomers. The evaluation results for n-dodecane hydroisomerization indicated that the activity of Pt/ZSM-22/ZSM-23 was the lowest, while the hydroisomerization selectivity was the highest among the three catalysts. The maximum yield of i-dodecane product was 68.3% over Pt/ZSM-22/ZSM-23 at 320 ℃.展开更多
Monometallic catalyst Pt/SAPO-11 was prepared by impregnation method.Bimetallic catalysts LaPt/SAPO-11 or CePt/SAPO-11 was prepared by sequential impregnation method.The catalysts were characterized by X-ray diffracti...Monometallic catalyst Pt/SAPO-11 was prepared by impregnation method.Bimetallic catalysts LaPt/SAPO-11 or CePt/SAPO-11 was prepared by sequential impregnation method.The catalysts were characterized by X-ray diffraction(XRD),nitrogen adsorption,temperature-programmed desorption of ammonia(NH3-TPD),and Fourier transform infrared spectroscopy(FT-IR) techniques.The results showed that with the addition of rare earths the BET surface areas,pore volume,the amount of Bronsted acid and the total acidity of catalys...展开更多
Rational regulation on pore structure and active site density plays critical roles in enhancing the performance of Fe-N-C catalysts. As the microporous structure of the carbon substrate is generally regarded as the ac...Rational regulation on pore structure and active site density plays critical roles in enhancing the performance of Fe-N-C catalysts. As the microporous structure of the carbon substrate is generally regarded as the active site hosts, its hostility to electron/mass transfer could lead to the incomplete fulfillment of the catalytic activity. Besides, the formation of inactive metallic Fe particles during the conventional catalyst synthesis could also decrease the active site density and complicate the identification of real active site. Herein, we developed a facial hydrogen etching methodology to yield single site Fe-N-C catalysts featured with micro/mesoporous hierarchical structure. The hydrogen concentration in pyrolysis process was designated to effectively regulate the pore structure and active site density of the resulted catalysts.The optimized sample achieves excellent ORR catalytic performance with an ultralow H2O2 yield(1%)and superb stability over 10,000 cycles. Our finding provides new thoughts for the rational design of hierarchically porous carbon-based materials and highly promising non-precious metal ORR catalysts.展开更多
Fe/N/C catalysts,synthesized through the pyrolysis of Fe-doped metal–organic framework (MOF) precursors,have attracted extensive attention owing to their promising oxygen reduction reaction (ORR) catalytic activity i...Fe/N/C catalysts,synthesized through the pyrolysis of Fe-doped metal–organic framework (MOF) precursors,have attracted extensive attention owing to their promising oxygen reduction reaction (ORR) catalytic activity in fuel cells and/or metal-air batteries.However,post-treatments (acid washing,second pyrolysis,and so on) are unavoidable to improve ORR catalytic activity and stability.The method for introducing Fe^(3+) sources (anhydrous Fe Cl_(3)) into the MOF structure,in particular,is a critical step that can avoid time-consuming post-treatments and result in more exposed Fe-N_(x) active sites.Herein,three different Fe doping strategies were systematically investigated to explore their influence on the types of active sites formed and ORR performance.Fe-NC(Zn^(2+)),synthesized by one-step pyrolysis of Fe doped ZIF-8 (Zn^(2+)) precursor which was obtained by adding the anhydrous Fe Cl_(3)source into the Zn(NO_(3))_(2)·6H_(2)O/methanol solution before mixing,possessed the highest Fe-N_(x)active sites due to the high-efficiency substitution of Zn^(2+)ions with Fe^(3+) ions during ZIF-8 growth,the strong interaction between Fe^(3+) ions and N atoms of 2-Methylimidazole (2-MIm),and ZIF-8’s micropore confinement effect.As a result,Fe-NC(Zn^(2+)) presented high ORR activity in the entire p H range (p H=1,7,and 13).At p H=13,Fe-NC(Zn^(2+)) exhibited a half-wave potential (E1/2) of 0.95 V (vs.reversible hydrogen electrode),which was 70 m V higher than that of commercial Pt/C.More importantly,Fe-NC(Zn^(2+)) showed superior ORR stability in neutral media without performance loss after 5,000 cycles.A record-high open-circuit voltage(1.9 V) was obtained when Fe-NC(Zn^(2+)) was used as a cathodic catalyst in assembled Mg-air batteries in neutral media.The assembled liquid and all-solid Mg-air batteries with high performance indicated that Fe-NC(Zn^(2+)) has enormous potential for use in flexible and wearable Mg-air batteries.展开更多
A series of Ni/AlMCM-41 catalysts with different nickel contents was prepared via the incipient wetness impregnation method. The effects of the nickel content on the structure, acidity and metal function of the cataly...A series of Ni/AlMCM-41 catalysts with different nickel contents was prepared via the incipient wetness impregnation method. The effects of the nickel content on the structure, acidity and metal function of the catalysts were studied by using different techniques. In the test of n-dodecane hydroconversion, it was found that the metal and acid functions were well balanced over a 2.0%Ni(mass fraction)/AlMCM-41 catalyst, which gave the maximal isomerization selectivity and a homolytic cleavage products.展开更多
Supported KVO3 catalysts were prepared by impregnating different kinds of supporters (α-Al2O3, γ-Al2O3 and SiO2 powders) with a KVO3 solution. The activity of the bare supporters and supported catalysts were ev...Supported KVO3 catalysts were prepared by impregnating different kinds of supporters (α-Al2O3, γ-Al2O3 and SiO2 powders) with a KVO3 solution. The activity of the bare supporters and supported catalysts were evaluated in a continuous micro-reactivity test unit, with n-butane as a raw material. The results show that KVO3 has no catalytic activity, but it can increase the selectivity to light olefins. The supporter of α-Al2O3 has good catalytic performance for n-butane cracking when the reaction temperature is below 700℃.展开更多
文摘Hanyu Xu 1,Xuedan Song 1,*,Qing Zhang 1,Chang Yu 1,Jieshan Qiu 1,2,*1 Liaoning Key Lab for Energy Materials and Chemical Engineering,State Key Laboratory of Fine Chemicals,School of Chemical Engineering,Dalian University of Technology,Dalian 116024,Liaoning Province,China.
基金This project was supported by the National Natural Science Foundation of China. (No.29974024,20254001)
文摘Copolymerization of styrene (St) with N-phenylmaleimide (NPMI) was studied with rare earth coordination catalyst Nd(naph)3-AlEt3 in toluene. Characterization of the copolymers showed that the copolymers possess an alternating structure.
文摘The catalysts were prepared by the temperature programmed reaction (TPR) of MoO3 with NH3 at various temperatures in the range of 573K～973K, and their hydrodenitrogenation (HDN) activities were tested in situ.It is shown that molybdenum nitrid(Mo2N) was formed above 923K and its intermediate MoO2 formed at about 573～623K under the rapid (5K/min.) TPR conditions.Mo2N is the most active species for pyridine HDN among MoO3,MoO2,MoS2,and Mo2N. Moreover,it can be promoted by adding Ni component.It is shown that the Ni/Mo2N catalyst prepared by adding some NiO into the precursor MoO3 has a steady HDN activity Which is far higher than that of the commercial sulfided NiMo/Al2O3(HR346) catalyst.
基金supported by the Natural Science Foundation of China (Nos. 21376261, 21173270)the Beijing Natural Science Foundation (2142027)+1 种基金Doctor select Foundation (No. 20130007110007)the National Hi-Tech Research and Development Program (863) of China (No. 2013AA065302)
文摘Selective catalytic reduction technology using NH3 as a reducing agent（NH3-SCR） is an effective control method to remove nitrogen oxides. TiO2-supported vanadium oxide catalysts with different levels of Ce and Sb modification were prepared by an impregnation method and were characterized by X-ray diffractometer（XRD）, Brunauer-Emmett-Teller（BET）, Transmission electron microscopy（TEM）, Fourier transform infrared spectroscopy（FT-IR）, UV-Vis diffuse reflectance spectroscopy（UV-Vis DRS）, Raman and Hydrogen temperature-programmed reduction（H2-TPR）. The catalytic activities of V5 CexS by/TiO2 catalysts for denitration were investigated in a fixed bed flow microreactor. The results showed that cerium, vanadium and antimony oxide as the active components were well dispersed on TiO2, and the catalysts exhibited a large number of d-d electronic transitions, which were helpful to strengthen SCR reactivity. The V5 CexS by/TiO2 catalysts exhibited a good low temperature NH3-SCR catalytic activity. In the temperature range of 210 to 400℃, the V5 CexS by/TiO2 catalysts gave NO conversion rates above 90%. For the best V5Ce35Sb2/TiO2 catalyst, at a reaction temperature of 210℃, the NO conversion rate had already reached 90%. The catalysts had different catalytic activity with different Ce loadings. With the increase of Ce loading, the NO conversion rate also increased.
基金financially supported by the National Natural Science Foundation of China(Nos. 21165016, 21175108, 21265018)the Science and Technology Support Projects of Gansu Province (Nos. 1011GKCA025, 090GKCA036,1208RJZM289)
文摘A novel three-dimensional (3D) layered MoS2@graphene functionalized with nitrogen-doped graphene quantum dots (MoS2@N-GQDs-GR) composites as an enhanced electrochemical hydrogen evolution catalyst. The few layered MoS2 nanoflowers supported on N-GQDs-GR surface were elaborately fabricated by one-pot hydrothermal method, which MoS2 and N-GQDs-GR exist in a bonding manner of Mo-N. In addition, due to the layered MoS2 sheet edge exposes more hydrogen evolution active sites and N-GQDs-GR have high conductivity, the composites exhibit prominent electrocatalytic activity with a low overpotential 99 mV, a small Tafel slope 49.3 mV/dec. Therefore, that the current work will develop HER catalysts may replace Pt.
文摘An efficient and versatile practical protocol for the chemoselective N-tert-butoxycarbonylation of amines using Nano-γ-Fe2O3 and (BOC)2O. Nano-γ-Fe2O3 was applied as an efficient, green, heterogeneous and reusable catalyst at ambient temperature;the method is general for the preparation of N-Boc derivatives of aliphatic, heterocyclic, aromatic as well as amino acid derivatives.
基金Supported by the Educational Com mittee of L iaoning Province
文摘The effects of the substituents on the cyclopentadienyl ring and the reducing agents on the catalytic activity and the stability of titanocene/NaH or n BuLi systems for the hydrogenation of olefins were investigated. For the catalyst systems composed of titanocene/NaH or n BuLi, the nature and the number of the substituents on the cyclopentadienyl ring control the catalytic behavior of those two systems. The effect of the reducing agent on the catalytic activity is relatively small. In addition, the characters of the hydrogenation of various olefins catalyzed respectively by Cp 2TiCl 2/NaH or n BuLi systems were compared.
基金financially supported by the National Natural Science Foundation of China(21573167,21633008,91545205,21125312)National Key Research and Development Program(2016YFB0101203)+2 种基金the National Basic Research Program(2012CB932800,2012CB215500)the Doctoral Fund of Ministry of Education of China(20110141130002)the Fundamental Research Funds for the Central Universities(2014203020207)
文摘An environmentally friendly precursor, adenosine, has been used as a dual source of C and N to synthesize nitrogen-doped carbon catalyst with/without Fe. A hydrothermal carbonization method has been used and water is the carbonization media. The morphology of samples with/without Fe component has been compared by HRTEM, and the result shows that Fe can promote the graphitization of carbon. Further electro-chemical test shows that the oxygen reduction reaction（ORR） catalytic activity of Fe-containing sample（C–Fe N） is much higher than that of the Fe-free sample（C–N）. Additionally, the intermediates of C–Fe N formed during each synthetic procedure have been thoroughly characterized by multiple methods,and the function of each procedure has been discussed. The C–Fe N sample exhibits high electro-catalytic stability and superior electro-catalytic activity toward ORR in alkaline media, with its half-wave potential 20 mV lower than that of commercial Pt/C（40 wt%）. It is further incorporated into alkaline polymer electrolyte fuel cell（APEFC） as the cathode material and led to a power density of 100 m W/cm;.
基金Supported by the National Natural Science Foundation of China(21177028,21477022)
文摘CePO4 （in particular, monoclinic CePO4） has been rarely used to make supported catalysts. Herein, monoclinic CeP04 nanoparticles were prepared by calcining hexagonal CePO4 nanomds （prepared by precipitation） in air at 900 ℃. Monoclinic CePO4 nanowires were prepared by calcining hexagonal CePO4 nanowires （prepared by hydrothermal synthesis at 150 ℃） in air at 900 ℃. Both monoclinic CePO4 materials were used to support Rh2O3 by impregnation using Rh（NO3）3 as a precursor （followed by calcination）. The catalytic performance of Rh2O3/monoclinic CePO4 composite materials in N2O decomposition and CO oxidation was investigated. It was found that Rh2O3 supported on monoclinic CePO4 nanowims was much more active than Rh2O3 supported on monoclinic CePO4 nanoparticles. The stability of catalysts as a function of reaction time on stream was studied in both reactions. The influence of co-fed CO2, O2, and H2O on the catalytic activity in N20 decomposition was also studied. These catalysts were characterized by employing N2 adsorption-desorption, ICP-OES, XRD, TEM, XPS, H2-TPR, O2-TPD, and CO2-TPD. The correlation between physicochemical properties and catalytic properties was discussed.
基金The International S&T Cooperation Program of China(No.2014DFE70150)
文摘Ni-based catalysts supported by γ-Al_2O_3 were prepared for improving the lower heating value( LHV) of biomass gasification fuel gas through methanation. Prior to the performance tests, the physico-chemical properties of the catalyst samples were characterized by N_2 isothermal adsorption/desorption, X-ray diffraction( XRD) and a scanning electron microscope( SEM). Afterwards, a series of experiments were carried out to investigate the catalytic performance and the results showthat catalysts with 15% and20% Ni loadings have better methanation catalytic effect than those with 5% and 10% Ni loadings in terms of elevating the LHV of biomass gasification fuel gas. M oreover, controllable influential factors such as the reaction temperature, the H_2/CO ratio and the water content occupy an important position in the methanation of biomass gasification fuel gas. 15 Ni/γ-Al_2O_3 and 20 Ni/γ-Al_2O_3 catalysts have a higher CO conversion and CH_4 selectivity at 350 ℃ and the LHV of biomass gasification fuel gas can be largely increased by 34. 3 % at 350 ℃. Higher H_2/CO ratio and a lower water content are more beneficial for improving the LHV of biomass gasification fuel gas when considering the combination of both CO conversion and CH_4 selectivity. This is due to the fact that a higher H_2/CO ratio and lower water content can increase the extent of the methanation reaction.
基金supported by the National Thousand Talents Plan of Chinathe National Natural Science Foundation of China(Grant Nos.21673014 and U1766216)+1 种基金the 111 project(B17002)funded by the Ministry of Education of Chinathe Fundamental Research Funds for the Central Universities of China
文摘Proton exchange membrane fuel cells(PEMFC)have attracted much attention because of their high energy conversion efficiency,high power density and zero emission of pollutants.However,the high cost of the cathode platinum group metal(PGM)catalysts creates a barrier for the large-scale application of PEMFC.Tremendous efforts have been devoted to the development of low-cost PGM-free catalysts,especially the Fe-N-C catalysts,to replace the expensive PGM catalysts.However,the characterization methods and evaluation standards of the catalysts varies,which is not conducive to the comparison of PGM-free catalysts.U.S.Department of energy(DOE)is the only authority that specifies the testing standards and activity targets for PGM-free catalysts.In this review,the major breakthroughs of Fe-N-C catalysts are outlined with the reference of DOE standards and targets.The preparation and characteristics of these highly active Fe-N-C catalysts are briefly introduced.Moreover,the efforts on improving the mass transfer and the durability issue of Fe-N-C fuel cell are discussed.Finally,the prospective directions concerning the comprehensive evaluation of the Fe-N-C catalysts are proposed.
基金supported by the National Natural Science Foundation of China(51722103,52071231 and 51571149)the Natural Science Foundation of Tianjin City(19JCJQJC61900)。
文摘Atomically dispersed iron-nitrogen-carbon(Fe-N-C) catalysts have emerged as the most promising alternative to the expensive Pt-based catalysts for the oxygen reduction reaction(ORR) in proton exchange membrane fuel cells(PEMFCs),however suffer from low site density of active Fe-N4 moiety and limited mass transport during the catalytic reaction.To address these challenges,we report a three-dimensional(3D) metal-organic frameworks(MOF)-derived Fe-N-C single-atom catalyst.In this well-designed Fe-N-C catalyst,the micro-scale interconnected skeleton,the nano-scale ordered pores and the atomic-scale abundant carbon edge defects inside the skeleton significantly enhance the site density of active Fe-N4 moiety,thus improving the Fe utilization in the final catalyst.Moreover,the combination of the above mentioned micro-and nano-scale structures greatly facilitates the mass transport in the 3D Fe-N-C catalyst.Therefore,the multiscale engineered Fe-N-C single-atom catalyst achieves excellent ORR performance under acidic condition and affords a significantly enhanced current density and power density in PEMFC.Our findings may open new opportunities for the rational design of FeN-C catalysts through multiscale structural engineering.
基金the financial supports form Petrochina(050508-04-02)the National Natural Science Foundation of China(No.21073235,and 20833011)
文摘Hydroisomerization catalysts Pt/ZSM-22, Pt/ZSM-23, and Pt/ZSM-22/ZSM-23 were prepared by supporting Pt on ZSM-22, ZSM-23, and intergrowth zeolite ZSM-22/ZSM-23, respectively. The typical physicochemical properties of these catalysts were characterized by X-Ray Diffraction （XRD）, N2 absorption-desorption, Pyridine-Fourier Transform Infrared （Py-FTIR）, Transmission Electron Microscopy （TEM）, X-Ray Fluorescence （XRF）, Scanning Electron Microscopy （SEM） and NH3- Temperature Programmed Desorption （NH3-TPD）, and the performance of these catalysts in n-dodecane hydroisomerization was evaluated in a continuous down-flow fixed bed with a stainless steel tubular reactor. The characterization results indicated that the intergrowth zeolite ZSM-22/ZSM-23 possessed the dual structure of ZSM-22 and ZSM-23, and the catalyst Pt/ZSM-22/ZSM-23 had similar pores and weak acidity to Pt/ZSM-22 and Pt/ZSM-23 catalysts. Moreover, Pt/ZSM-22/ZSM-23 catalyst showed a high selectivity in hydroisomerization of long chain n-alkanes to mono-branched isomers. The evaluation results for n-dodecane hydroisomerization indicated that the activity of Pt/ZSM-22/ZSM-23 was the lowest, while the hydroisomerization selectivity was the highest among the three catalysts. The maximum yield of i-dodecane product was 68.3% over Pt/ZSM-22/ZSM-23 at 320 ℃.
基金supported by the Foundation of Jiangsu Key Laboratory of Precious Metals Chemistry (SYGK0710)Natural Scientific Foundation of Jiangsu Teachers University of Technology (KYY06029)
文摘Monometallic catalyst Pt/SAPO-11 was prepared by impregnation method.Bimetallic catalysts LaPt/SAPO-11 or CePt/SAPO-11 was prepared by sequential impregnation method.The catalysts were characterized by X-ray diffraction(XRD),nitrogen adsorption,temperature-programmed desorption of ammonia(NH3-TPD),and Fourier transform infrared spectroscopy(FT-IR) techniques.The results showed that with the addition of rare earths the BET surface areas,pore volume,the amount of Bronsted acid and the total acidity of catalys...
基金supported by the National Natural Science Foundation of China(21633008,21433003,U1601211,21733004)National Science and Technology Major Project(2016YFB0101202)+1 种基金Jilin Province Science and Technology Development Program(20150101066JC,20160622037JC,20170203003SF,20170520150JH)Hundred Talents Program of Chinese Academy of Sciences and the Recruitment Program of Foreign Experts(WQ20122200077)
文摘Rational regulation on pore structure and active site density plays critical roles in enhancing the performance of Fe-N-C catalysts. As the microporous structure of the carbon substrate is generally regarded as the active site hosts, its hostility to electron/mass transfer could lead to the incomplete fulfillment of the catalytic activity. Besides, the formation of inactive metallic Fe particles during the conventional catalyst synthesis could also decrease the active site density and complicate the identification of real active site. Herein, we developed a facial hydrogen etching methodology to yield single site Fe-N-C catalysts featured with micro/mesoporous hierarchical structure. The hydrogen concentration in pyrolysis process was designated to effectively regulate the pore structure and active site density of the resulted catalysts.The optimized sample achieves excellent ORR catalytic performance with an ultralow H2O2 yield(1%)and superb stability over 10,000 cycles. Our finding provides new thoughts for the rational design of hierarchically porous carbon-based materials and highly promising non-precious metal ORR catalysts.
基金supported by the National Natural Science Foundation of China(22171266)the FJIRSM&IUE Joint Research Fund(RHZX-2019-002)+2 种基金the STS Project(KFJ-STS-QYZD-2021-09002)the National Key Basic Research Program of China(2017YFA0403402)the Project of the National Natural Science Foundation of China(U1932119)。
文摘Fe/N/C catalysts,synthesized through the pyrolysis of Fe-doped metal–organic framework (MOF) precursors,have attracted extensive attention owing to their promising oxygen reduction reaction (ORR) catalytic activity in fuel cells and/or metal-air batteries.However,post-treatments (acid washing,second pyrolysis,and so on) are unavoidable to improve ORR catalytic activity and stability.The method for introducing Fe^(3+) sources (anhydrous Fe Cl_(3)) into the MOF structure,in particular,is a critical step that can avoid time-consuming post-treatments and result in more exposed Fe-N_(x) active sites.Herein,three different Fe doping strategies were systematically investigated to explore their influence on the types of active sites formed and ORR performance.Fe-NC(Zn^(2+)),synthesized by one-step pyrolysis of Fe doped ZIF-8 (Zn^(2+)) precursor which was obtained by adding the anhydrous Fe Cl_(3)source into the Zn(NO_(3))_(2)·6H_(2)O/methanol solution before mixing,possessed the highest Fe-N_(x)active sites due to the high-efficiency substitution of Zn^(2+)ions with Fe^(3+) ions during ZIF-8 growth,the strong interaction between Fe^(3+) ions and N atoms of 2-Methylimidazole (2-MIm),and ZIF-8’s micropore confinement effect.As a result,Fe-NC(Zn^(2+)) presented high ORR activity in the entire p H range (p H=1,7,and 13).At p H=13,Fe-NC(Zn^(2+)) exhibited a half-wave potential (E1/2) of 0.95 V (vs.reversible hydrogen electrode),which was 70 m V higher than that of commercial Pt/C.More importantly,Fe-NC(Zn^(2+)) showed superior ORR stability in neutral media without performance loss after 5,000 cycles.A record-high open-circuit voltage(1.9 V) was obtained when Fe-NC(Zn^(2+)) was used as a cathodic catalyst in assembled Mg-air batteries in neutral media.The assembled liquid and all-solid Mg-air batteries with high performance indicated that Fe-NC(Zn^(2+)) has enormous potential for use in flexible and wearable Mg-air batteries.
基金the Funds for the National Key Fundamental Research and Developm ent Projects of China (No.G19990 2 2 4 0 2 )
文摘A series of Ni/AlMCM-41 catalysts with different nickel contents was prepared via the incipient wetness impregnation method. The effects of the nickel content on the structure, acidity and metal function of the catalysts were studied by using different techniques. In the test of n-dodecane hydroconversion, it was found that the metal and acid functions were well balanced over a 2.0%Ni(mass fraction)/AlMCM-41 catalyst, which gave the maximal isomerization selectivity and a homolytic cleavage products.
文摘Supported KVO3 catalysts were prepared by impregnating different kinds of supporters (α-Al2O3, γ-Al2O3 and SiO2 powders) with a KVO3 solution. The activity of the bare supporters and supported catalysts were evaluated in a continuous micro-reactivity test unit, with n-butane as a raw material. The results show that KVO3 has no catalytic activity, but it can increase the selectivity to light olefins. The supporter of α-Al2O3 has good catalytic performance for n-butane cracking when the reaction temperature is below 700℃.
