Freeze-thaw(F-T)cycle is receiving increasing attention as a primary threat to the long-term stability of rock engineering in high-elevation regions.In this study,artificial F-T cycle tests are first conducted on pre-...Freeze-thaw(F-T)cycle is receiving increasing attention as a primary threat to the long-term stability of rock engineering in high-elevation regions.In this study,artificial F-T cycle tests are first conducted on pre-flawed sandstone specimens with real-time frost heave pressure(FHP)monitoring,followed by subsequent cyclic loading tests with different maximum stresses.Given the water-ice-sandstone interaction,the evolution process of FHP in flaws can be divided into six phases,i.e.initial,silence,eruption,reduction,second-arising,and dissipation phases.Its magnitude exhibits an exponential decrease with increasing F-T cycle number.The influences of F-T cycles and the maximum stress on the fatigue mechanical characteristics of flawed sandstone are revealed.Subjected to higher F-T cycles and maximum stress,larger irreversible strain and less dissipated energy are accumulated inside flawed sandstone specimens,leading to faster damage and lower fatigue life.The three-stage evolution characters of irreversible strain and dissipated energy are both weakened by repeated F-T treatment,i.e.the prolonged initial and accelerated stages and shortened stable stage.In addition,the repeated F-T cycles diminish the impact of prefabricated flaws on cracking behavior of flawed sandstone specimens,and the fatigue failure pattern changes from shear-dominated failure with a transfixion shear band to tensile-dominated failure with massive tensile cracks as the F-T cycle number increases.Employing the scanning electron microscopy(SEM),the underlying damage mechanisms of flawed rocks under the coupling effect of F-T treatment and cyclic loading are discussed.Finally,an F-T-fatigue damage model is proposed based on FHP evolution and irreversible strain,which possesses distinct physical significance and reasonably quantifies the F-T deterioration and fatigue damage accumulation of flawed rocks.展开更多
In order to investigate the dynamic mechanical properties of amphibolite and sericite-quartz schist under confi ning pressure, two rocks are subjected to impact loadings with different strain rates and confi ning pres...In order to investigate the dynamic mechanical properties of amphibolite and sericite-quartz schist under confi ning pressure, two rocks are subjected to impact loadings with different strain rates and confi ning pressures by using split Hopkinson pressure bar equipment with a confi ning pressure device. Based on the experimental results, the stress-strain curves are analyzed and the effects of confi ning pressure and strain rates on the dynamic compressive strength, peak strain and failure mode are summarized. The results show that:(1) The characteristics of two rocks in the ascent stage of the stressstrain curve are basically the same, but in the descent stage, the rocks gradually show plastic deformation characteristics as the confi ning pressure increases.(2) The dynamic compressive strength and peak strain of two rocks increase as the strain rate increases and the confi ning pressure effects are obvious.(3) Due to the effect of confi ning pressure, the normal stress on the damage surface of the rock increases correspondingly, the bearing capacity of the crack friction exceeds the material cohesion and the slippage of the fractured rock is controlled, which all lead to the compression and shear failure mode of rock. The theoretical analysis and experimental methods to study the dynamic failure mode and other related characteristics of rock are useful in developing standards for engineering practice.展开更多
Two loosely coupled single degree of freedom (SDOF) systems were used to model the flexural and direct shear responses of one-way reinforced concrete slabs subjected to explosive loading. Blast test results show that ...Two loosely coupled single degree of freedom (SDOF) systems were used to model the flexural and direct shear responses of one-way reinforced concrete slabs subjected to explosive loading. Blast test results show that the SDOF systems are accurate in predicting the failure mode of the slab under blast loads by incorporating the effects of the strain rate effect caused by rapid load application. Based on different damage criteria, pressure-impulse (P-I) diagrams of the two failure modes were analyzed with the SDOF systems. The effects of span length, concrete strength, and reinforcement ratio of the slab on the P-I diagram were also investigated. Results indicate that a slab tends to fail in direct shear mode when it is of a smaller span length and tends to fail in flexure mode when it is of a larger span length. With the increase of the concrete strength or reinforced ratio, both the flexure and shear capacity increase. Based on numerical results, a simplified method and a semi analytical equation for deriving the P-I diagram are proposed for different failure modes and damage levels.展开更多
This paper presents the design, analysis and experimental study of a loading system for heavy-duty nodes test based on a large-scale multi-directional in-plane loading device, which has been used in a full-scale heavy...This paper presents the design, analysis and experimental study of a loading system for heavy-duty nodes test based on a large-scale multi-directional in-plane loading device, which has been used in a full-scale heavy-duty support node test. Test loads of the support reached 6 567 kN with multi-directional loading requirements, which outrange the capacity of the available loading devices. Through the reinforcement of a large-scale multi-directional inplane loading device, the innovative design of a self-balanced load transferring device, and other arrangement considerations of the loading system, the test was implemented and the loading capacity of the ring was considerably enlarged. Due to the heavy loading requirements, some checking computations of the ring and the load transferring device outranged the limit of the Chinese national code "Code for Design of Steel Structures (GB 50017—2003)", thus elastic-plastic finite element (FE) analysis was carried out on the two devices, and also the real-time monitoring on the whole loading systems during experiments to ensure test safety. FE analysis and test results show that the loading system worked elastically during experiments.展开更多
The modified suction caisson(MSC) is a novel type of foundation for ocean engineering, consisting of a short external closed-top cylinder-shaped structure surrounding the upper part of the regular suction caisson(RSC)...The modified suction caisson(MSC) is a novel type of foundation for ocean engineering, consisting of a short external closed-top cylinder-shaped structure surrounding the upper part of the regular suction caisson(RSC). The MSC can provide larger lateral bearing capacity and limit the deflection compared with the RSC. Therefore, the MSC can be much more appropriate to use as an offshore wind turbine foundation. Model tests on the MSC in saturated sand subjected to monotonic lateral loading were carried out to investigate the effects of external structure sizes on the sand surface deformation and the earth pressure distribution along the embedded depth. Test results show that the deformation range of the sand surface increases with the increasing width and length of the external structure. The magnitude of sand upheaval around the MSC is smaller than that of the RSC and the sand upheaval value around the MSC in the loading direction decreases with the increasing external structure dimensions. The net earth pressure in the loading direction acting on the internal compartment of the MSC is smaller than that of the RSC at the same embedded depth. The maximum net earth pressure acting on the external structure outer wall in the loading direction is larger than that of the internal compartment, indicating that a considerable amount of the lateral load and moment is resisted by the external skirt structure.展开更多
In order to investigate the relationship between bar diameter and loading rate of the split Hopkinson pressure bar(SHPB) setup under the failure of rock specimen and realize the medium strain rate loading of specimen,...In order to investigate the relationship between bar diameter and loading rate of the split Hopkinson pressure bar(SHPB) setup under the failure of rock specimen and realize the medium strain rate loading of specimen,new SHPB setups with different elastic bar's diameters of 22,36,50 and 75 mm were constructed.The tests were carried out on these setups at different loading rates,and the specimens had the same diameter of elastic bars and same ratio of length to diameter.The test results show that the larger the elastic bar's diameter is,the less the loading rate is needed to cause specimen failure,they show good power relationship,and that under the same strain rate loading,specimens are broken more seriously with larger diameter SHPB setup than with smaller one.展开更多
The split-Hopkinson pressure bar(SHPB)is a widely used experimental technique for studying the mechanical properties of materials at high strain rates.There are two kinds of loading methods applied in the SHPB techniq...The split-Hopkinson pressure bar(SHPB)is a widely used experimental technique for studying the mechanical properties of materials at high strain rates.There are two kinds of loading methods applied in the SHPB technique,namely one-side loading and symmetric loading.However,the experimental accuracy of the two loading methods is affected by the interface contact.The present study focused on the inadequate contact caused by the misalignment of the pressure bars.The commercial software ABAQUS was used for simulations.The result shows that the inadequate contact caused by the alignment of the bars has a non-negligible effect on the calculated results.Compared with the one-side loading Hopkinson pressure bar,the symmetric loading Hopkinson pressure bar has a more relaxed requirement for the alignment of the bars.The conclusion arrived at in this paper can help researchers to make a reasonable choice between one-side and symmetric loading Hopkinson pressure bars according to actual requirements.展开更多
A hull structure is prone to local deformation and damage due to the pressure load on the surface.How to simulate surface pressure is an important issue in ship structure test.The loading mode of hydraulic actuator co...A hull structure is prone to local deformation and damage due to the pressure load on the surface.How to simulate surface pressure is an important issue in ship structure test.The loading mode of hydraulic actuator combined with high-pressure flexible bladder was proposed,and the numerical model of the loading device based on flexible bladder was established.The design and analysis method of high-pressure flexible bladder based on aramid-fiber reinforced thermoplastic polyurethane was proposed to break through the surface pressure loading technology of ship structures.The surface pressure loading system based on flexible bladder was developed.The ultimate strength verification test of the box girder under the combined action of bending moment and pressure was carried out to systematically verify the feasibility and applicability of the loading system.The results show that the surface pressure loading technology can be used well for applying uniform pressure to ship structures.Compared with the traditional surface loading methods,the improved device can be applied with horizontal constant pressure load,with rapid response and safe process,and the pressure load is always stable with the increase of the bending moment load during the test.The requirement for uniform loading in the comprehensive strength test of large structural models is satisfied and the accuracy of the test results is improved by this system.展开更多
The study of pressure stimulated current(PSC)changes of rocks is significant to monitor dynamic disasters in mines and rock masses.The existing studies focus on change laws and mechanism of currents generated under th...The study of pressure stimulated current(PSC)changes of rocks is significant to monitor dynamic disasters in mines and rock masses.The existing studies focus on change laws and mechanism of currents generated under the loading of rocks.An electrical and mechanics test system was established in this paper to explore the impacts of loading rates on PSCs.The results indicated that PSC curves of different rocks had different change laws under low/high loading rates.When the loading rate was relatively low,PSC curves firstly changed gently and then increased exponentially.Under high loading rates,PSC curves experienced the rapid increase stage,gentle increase stage and sudden change stage.The compressive strength could greatly affect the peak PSC in case of rock failure.The loading rate was a key factor in average PSC.Under low loading rates,the variations of PSCs conformed to the damage charge model of fracture mechanics,while they did not at the fracture moment.Under high loading rates,the PSCs at low stress didn’t fit the model due to the stress impact effects.The experimental results could provide theoretical basis for the influence of loading rates on PSCs.展开更多
To reveal the water inrush mechanics of underground deep rock mass subjected to dynamic disturbance such as blasting, compression-shear rock crack initiation rule and the evolution of crack tip stress intensity factor...To reveal the water inrush mechanics of underground deep rock mass subjected to dynamic disturbance such as blasting, compression-shear rock crack initiation rule and the evolution of crack tip stress intensity factor are analyzed under static-dynamic loading and seepage water pressure on the basis of theoretical deduction and experimental research. It is shown that the major influence factors of the crack tip stress intensity factor are seepage pressure, dynamic load, static stress and crack angle. The existence of seepage water pressure aggravates propagation of branch cracks. With the seepage pressure increasing, the branch crack experiences unstable extension from stable propagation. The dynamic load in the direction of maximum main stress increases type I crack tip stress intensity factor and its influence on type II crack intensity factor is related with crack angle and material property. Crack initiation angle changes with the dynamic load. The initial crack initiation angle of type I dynamic crack fracture is 70.5°. The compression-shear crack initial strength is related to seepage pressure, confining pressure, and dynamic load. Experimental results verify that the initial crack strength increases with the confining pressure increasing, and decreases with the seepage pressure increasing.展开更多
The characteristics of dynamic stress in the seabed under wave loading are constant principal stress and continuous rotation of the principal stress direction. Cyclic triaxial-torsional coupling shear tests were peffo...The characteristics of dynamic stress in the seabed under wave loading are constant principal stress and continuous rotation of the principal stress direction. Cyclic triaxial-torsional coupling shear tests were pefformed on saturated silt by the hollow cylinder apparatus under different relative densities, deviator stress ratios and vibration frequencies to study the development of pore water pressure of the saturated silt under wave loading. It was found that the development of pore water pressure follows the trend of ＂fast - steady - drastic＂. The turning point from fast to steady stage is not affected by relative density and deviator stress ratio. However, the turning point from steady to drastic stage relies on relative density and deviator stress ratio. The vibration cycle for the liquefaction of saturated silt decreases with increasing deviator stress ratio and increases with relative density. The vibration cycle for the liquefaction of the saturated silt increases with vibration frequency and reaches a peak value, after which it decreases with increasing vibration frequency for the relative density of 70%. But the vibration cycle for the liquefaction of saturated silt increases with vibration frequency for the relative density of 30%. The development of pore water pressure of the saturated silt is influenced by relative density and vibration frequency.展开更多
Existing studies have focused on the behavior of the retaining wall equipped with expanded polystyrene(EPS)geofoam inclusions under semi-infinite surcharge loading rather than limited surcharge loading.In this paper,t...Existing studies have focused on the behavior of the retaining wall equipped with expanded polystyrene(EPS)geofoam inclusions under semi-infinite surcharge loading rather than limited surcharge loading.In this paper,the failure mode and the earth pressure acting on the rigid retaining wall with EPS geofoam inclusions and granular backfills(henceforth referred to as EPS-wall),under limited surcharge loading are investigated through two-and three-dimensional model tests.The testing results show that different from the sliding of almost all the backfill in the EPS-wall under semi-infinite surcharge loading,only an approximately triangular backfill slides in the wall under limited surcharge loading.The distribution of the lateral earth pressure on the EPS-wall under limited surcharge loading is non-linear,and the distribution changes from the increase of the wall depth to the decrease with the increase of the limited surcharge loading.An approach based on the force equilibrium of a differential element is developed to predict the lateral earth pressure behind the EPS-wall subjected to limited surcharge loading,and its performance was fully validated by the three-dimensional model tests.展开更多
With the increase of underground engineering construction depth,the phenomenon of surrounding rock sudden failure caused by supporting structure failure occurs frequently.The conventional unloading con-fining pressure...With the increase of underground engineering construction depth,the phenomenon of surrounding rock sudden failure caused by supporting structure failure occurs frequently.The conventional unloading con-fining pressure(CUCP)test cannot simulate the plastic yielding and instantaneous unloading process of supporting structure to rock.Thus,a high stress loading-instantaneous unloading confining pressure(HSL-IUCP)test method was proposed and applied by considering bolt’s fracture under stress.The wall thickness of confining pressure plates and the material of bolts were changed to realize different confin-ing pressure loading stiffness(CPLS)and lateral maximum allowable deformation(LMAD).The superio-rity of HSL-ICPU method is verified compared with CUCP.The rock failure mechanism caused by sudden failure of supporting structure is obtained.The results show that when CPLS increases from 1.35 to 2.33 GN/m,rock’s peak strength and elastic modulus increase by 25.18%and 23.70%,respectively.The fracture characteristics change from tensile failure to tensile-shear mixed failure.When LMAD decreases from 0.40 to 0.16 mm,rock’s residual strength,peak strain,and residual strain decrease by 91.80%,16.94%,and 21.92%,respectively,and post-peak drop modulus increases by 140.47%.The test results obtained by this method are closer to rock’s real mechanical response characteristics compared with CUCP.展开更多
Hemispherical asymmetry in core dynamics induces degree-1 pressure variations at the core mantle boundary （CMB）, which in turn deforms the overlaying elastic mantle, at the same time keeps center of mass of the whol...Hemispherical asymmetry in core dynamics induces degree-1 pressure variations at the core mantle boundary （CMB）, which in turn deforms the overlaying elastic mantle, at the same time keeps center of mass of the whole Earth stationary in space. We develop a systematic procedure to deal with the degree-1 CMB pressure loading. We find by direct calculation a surprisingly negative load Love number h1=-1.425 for vertical displacement. Further analysis indicates that the negative hi corre- sponds to thickening above the positive load that defies intuition that pressure inflation pushes over- laying material up and thins the enveloping shell. We also redefine the pressure load Love numbers in general to enable comparison between the surface mass load and the CMB pressure load for the whole spectrum of harmonic degrees. We find that the gravitational perturbations from the two kinds of loads at degrees n〉l are very similar in amplitude but opposite in sign. In particular, if the CMB pressure variation at degree 2 is at the level of -1 hpa/yr （1 cm water height per year）, it would perturb the variation of Earth＇s oblateness, known as the J2, at the observed level.展开更多
A quasi-static/dynamic pressure-tension compound loading system was established in this paper for the research of cellular mechanical circumstances. Both radical and circumferential strain of the basement membrane wer...A quasi-static/dynamic pressure-tension compound loading system was established in this paper for the research of cellular mechanical circumstances. Both radical and circumferential strain of the basement membrane were studied and compared in theoretical calculations by using the FEA Software ABAQUS and experimental measurements. The tension of the basement membrane was studied both in ABUQUES results and experimental results, the relation between the height of the concave cavity, the radius of the membrane and the strain of the membrane were studied in details.展开更多
Skin integrity breakdown and pressure ulcer formation on the heel are predictable and preventable healthcare occurrences. By minimizing surface contact pressures that can cause heel capillary occlusion, heel off-loadi...Skin integrity breakdown and pressure ulcer formation on the heel are predictable and preventable healthcare occurrences. By minimizing surface contact pressures that can cause heel capillary occlusion, heel off-loading devices help mitigate the risk of decubitus ulceration. The purpose of this study is to investigate the efficacy of six off-loading methods commonly used in clinical settings to decrease heel contact pressure. Pressure mapping is used to evaluate contact pressure at the heel for underweight, normal weight, and overweight simulations. Based upon averages across four trials, it is shown that all devices reduce heel contact pressure when compared to no off-load- ing. The PRUventor™ boot exhibits significantly lower average pressure values than other off-load- ing strategies tested, suggesting that the PRUventor™ is the most effective off-loading device. From the analysis of the experimental data and comparison to similar data for respective off-loading alternatives, it is concluded that the PRUventor™ boot is an effective heel off-loading device for use in clinical settings.展开更多
By increasing the yield strengths of austenitic stainless steels for pressure vessels with strain hardening techniques,the elastic load bearing capacity of austenitic stainless steel pressure vessels can be significan...By increasing the yield strengths of austenitic stainless steels for pressure vessels with strain hardening techniques,the elastic load bearing capacity of austenitic stainless steel pressure vessels can be significantly improved.Two kinds of strain hardening methods are often used for austenitic stainless steel pressure vessels：Avesta model for ambient temperature applications and Ardeform model for cryogenic temperature applications.Both methods are obtained from conventional design rules based on the linear elastic theory,and only consider the hardening effect from materials.Consequently this limits the applications of strain hardening techniques for austenitic stainless steel pressure vessels because of safety concerns.This paper investigates the effect of strain hardening on the load bearing capacity of austenitic stainless steel pressure vessels under large deformation,based on the elastic-plastic theory.Firstly,to understand the effect of strain hardening on material behavior,the plastic instability loads of a round tensile bar specimen are derived under two different loading paths and validated by experiments.Secondly,to investigate the effect of strain hardening on pressure vessels strength, the plastic instability pressure under strain hardening is derived and further validated by finite element simulations.Further,the safety margin of pressure vessels after strain hardening is analyzed by comparing the safety factor values calculated from bursting tests,finite element analyses,and standards.The researching results show that the load bearing capacity of pressure vessels at ambient temperature is independent of the loading history when the effects of both material strain hardening and structural deformation are considered.Finite element simulations and bursting tests results show that the minimum safety factor of austenitic stainless steel pressure vessels with 5% strain hardening is close to the recommended value for common pressure vessels specified in the European pressure vessel standard.The proposed study also shows that in the strain hardening design of austenitic stainless steel pressure vessels,the calculation for plastic instability pressure could use theoretical formula or finite element analyses based on geometrical dimensions and material property parameters before strain hardening,but a 5%strain should be employed as a design limit.The proposed research can be used for the strain hardening design of austenitic stainless steel pressure vessels safely.展开更多
According to the interaction of three shallow tunnels with large section, the analytical solution to rock pressure has been derived and discussed. The load model is given when the bilateral tunnels are excavated. Acco...According to the interaction of three shallow tunnels with large section, the analytical solution to rock pressure has been derived and discussed. The load model is given when the bilateral tunnels are excavated. According to the model, the stresses of three tunnels and single tunnel are calculated and compared to analyze the distribution characteristics, where the stresses are influenced by controlling factors of clear distance, covering depth and inclination angle of ground surface. The results show that, in general, the bias distribution is more serious. Therefore, it is significant to settle down the load model of three shallow tunnels so as to determine the measure of reinforcement and design the structure of support. The model and results can be used as a theoretical basis in designation and further research of the three shallow tunnels.展开更多
Coal and gas outbursts are dynamic disasters in which a large mass of gas and coal suddenly emerges in a mining space within a split second.The interaction between the gas pressure and stress environment is one of the...Coal and gas outbursts are dynamic disasters in which a large mass of gas and coal suddenly emerges in a mining space within a split second.The interaction between the gas pressure and stress environment is one of the key factors that induce coal and gas outbursts.In this study,first,the coupling relationship between the gas pressure in the coal body ahead of the working face and the dynamic load was investigated using experimental observations,numerical simulations,and mine-site investigations.It was observed that the impact rate of the dynamic load on the gas-bearing coal can significantly change the gas pressure.The faster the impact rate,the speedier the increase in gas pressure.Moreover,the gas pressure rise was faster closer to the impact interface.Subsequently,based on engineering background,we proposed three models of stress and gas pressure distribution in the coal body ahead of the working face:static load,stress disturbance,and dynamic load conditions.Finally,the gas pressure distribution and outburst mechanism were investigated.The high concentration of gas pressure appearing at the coal body ahead of the working face was caused by the dynamic load.The gas pressure first increased gradually to a peak value and then decreased with increasing distance from the working face.The increase in gas pressure plays a major role in outburst initiation by resulting in the ability to more easily reach the critical points needed for outburst initiation.Moreover,the stronger the dynamic load,the greater the outburst initiation risk.The results of this study provide practical guidance for the early warning and prevention of coal and gas outbursts.展开更多
With von Mises yield criterion,the loading range of Net Section Collapse(NSC) Criteria is extended from combined tension and bending loadings to combined bending,torsion and internal pressure loadings.A new theoretica...With von Mises yield criterion,the loading range of Net Section Collapse(NSC) Criteria is extended from combined tension and bending loadings to combined bending,torsion and internal pressure loadings.A new theoretical analyzing method of plastic limit load for pressure pipe with incomplete welding defects based on the extended NSC Criteria is presented and the correlative formulas are deduced,the influences of pipe curvature,circumferential length and depth of incomplete welding defects on the plastic limit load of pressure pipe are considered as well in this method.Meanwhile,according to the orthogonal experimental design method,the plastic limit loads are calculated by the finite element method and compared with the theoretical values.The results show that the expressions of plastic limit load of pressure pipe with incomplete welding defects under bending,torsion and internal pressure based on extended NSC criteria are reliable.The study provides an important theoretical basis for the establishment of safety assessment measure towards pressure pipe with incomplete welding defects.展开更多
基金support from the National Natural Science Foundation of China(Grant Nos.42377144,52225904 and 52039007)supported by the New Cornerstone Science Foundation through the XPLORER PRIZE.
文摘Freeze-thaw(F-T)cycle is receiving increasing attention as a primary threat to the long-term stability of rock engineering in high-elevation regions.In this study,artificial F-T cycle tests are first conducted on pre-flawed sandstone specimens with real-time frost heave pressure(FHP)monitoring,followed by subsequent cyclic loading tests with different maximum stresses.Given the water-ice-sandstone interaction,the evolution process of FHP in flaws can be divided into six phases,i.e.initial,silence,eruption,reduction,second-arising,and dissipation phases.Its magnitude exhibits an exponential decrease with increasing F-T cycle number.The influences of F-T cycles and the maximum stress on the fatigue mechanical characteristics of flawed sandstone are revealed.Subjected to higher F-T cycles and maximum stress,larger irreversible strain and less dissipated energy are accumulated inside flawed sandstone specimens,leading to faster damage and lower fatigue life.The three-stage evolution characters of irreversible strain and dissipated energy are both weakened by repeated F-T treatment,i.e.the prolonged initial and accelerated stages and shortened stable stage.In addition,the repeated F-T cycles diminish the impact of prefabricated flaws on cracking behavior of flawed sandstone specimens,and the fatigue failure pattern changes from shear-dominated failure with a transfixion shear band to tensile-dominated failure with massive tensile cracks as the F-T cycle number increases.Employing the scanning electron microscopy(SEM),the underlying damage mechanisms of flawed rocks under the coupling effect of F-T treatment and cyclic loading are discussed.Finally,an F-T-fatigue damage model is proposed based on FHP evolution and irreversible strain,which possesses distinct physical significance and reasonably quantifies the F-T deterioration and fatigue damage accumulation of flawed rocks.
基金National Natural Science Foundation of China under Grant No.51378497
文摘In order to investigate the dynamic mechanical properties of amphibolite and sericite-quartz schist under confi ning pressure, two rocks are subjected to impact loadings with different strain rates and confi ning pressures by using split Hopkinson pressure bar equipment with a confi ning pressure device. Based on the experimental results, the stress-strain curves are analyzed and the effects of confi ning pressure and strain rates on the dynamic compressive strength, peak strain and failure mode are summarized. The results show that:(1) The characteristics of two rocks in the ascent stage of the stressstrain curve are basically the same, but in the descent stage, the rocks gradually show plastic deformation characteristics as the confi ning pressure increases.(2) The dynamic compressive strength and peak strain of two rocks increase as the strain rate increases and the confi ning pressure effects are obvious.(3) Due to the effect of confi ning pressure, the normal stress on the damage surface of the rock increases correspondingly, the bearing capacity of the crack friction exceeds the material cohesion and the slippage of the fractured rock is controlled, which all lead to the compression and shear failure mode of rock. The theoretical analysis and experimental methods to study the dynamic failure mode and other related characteristics of rock are useful in developing standards for engineering practice.
基金Project(JC11-02-18) supported by the Scientific Foundation of National University of Defense Technology, ChinaProject(11202236) supported by the National Natural Science Foundation of China
文摘Two loosely coupled single degree of freedom (SDOF) systems were used to model the flexural and direct shear responses of one-way reinforced concrete slabs subjected to explosive loading. Blast test results show that the SDOF systems are accurate in predicting the failure mode of the slab under blast loads by incorporating the effects of the strain rate effect caused by rapid load application. Based on different damage criteria, pressure-impulse (P-I) diagrams of the two failure modes were analyzed with the SDOF systems. The effects of span length, concrete strength, and reinforcement ratio of the slab on the P-I diagram were also investigated. Results indicate that a slab tends to fail in direct shear mode when it is of a smaller span length and tends to fail in flexure mode when it is of a larger span length. With the increase of the concrete strength or reinforced ratio, both the flexure and shear capacity increase. Based on numerical results, a simplified method and a semi analytical equation for deriving the P-I diagram are proposed for different failure modes and damage levels.
基金Supported by National Natural Science Foundation of China (No. 50878066)the National Key Technology R&D Program in the 11th Five-Year Plan of China (No. 2006BAJ01B02)the Key Technologies R&D Program of Heilongjiang Province, China (No. GB02C204)
文摘This paper presents the design, analysis and experimental study of a loading system for heavy-duty nodes test based on a large-scale multi-directional in-plane loading device, which has been used in a full-scale heavy-duty support node test. Test loads of the support reached 6 567 kN with multi-directional loading requirements, which outrange the capacity of the available loading devices. Through the reinforcement of a large-scale multi-directional inplane loading device, the innovative design of a self-balanced load transferring device, and other arrangement considerations of the loading system, the test was implemented and the loading capacity of the ring was considerably enlarged. Due to the heavy loading requirements, some checking computations of the ring and the load transferring device outranged the limit of the Chinese national code "Code for Design of Steel Structures (GB 50017—2003)", thus elastic-plastic finite element (FE) analysis was carried out on the two devices, and also the real-time monitoring on the whole loading systems during experiments to ensure test safety. FE analysis and test results show that the loading system worked elastically during experiments.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.51639002 and 51379118)the SDUST Research Fund(Grant No.2015KYTD104)
文摘The modified suction caisson(MSC) is a novel type of foundation for ocean engineering, consisting of a short external closed-top cylinder-shaped structure surrounding the upper part of the regular suction caisson(RSC). The MSC can provide larger lateral bearing capacity and limit the deflection compared with the RSC. Therefore, the MSC can be much more appropriate to use as an offshore wind turbine foundation. Model tests on the MSC in saturated sand subjected to monotonic lateral loading were carried out to investigate the effects of external structure sizes on the sand surface deformation and the earth pressure distribution along the embedded depth. Test results show that the deformation range of the sand surface increases with the increasing width and length of the external structure. The magnitude of sand upheaval around the MSC is smaller than that of the RSC and the sand upheaval value around the MSC in the loading direction decreases with the increasing external structure dimensions. The net earth pressure in the loading direction acting on the internal compartment of the MSC is smaller than that of the RSC at the same embedded depth. The maximum net earth pressure acting on the external structure outer wall in the loading direction is larger than that of the internal compartment, indicating that a considerable amount of the lateral load and moment is resisted by the external skirt structure.
基金Project(10472134) supported by the National Natural Science Foundation of China
文摘In order to investigate the relationship between bar diameter and loading rate of the split Hopkinson pressure bar(SHPB) setup under the failure of rock specimen and realize the medium strain rate loading of specimen,new SHPB setups with different elastic bar's diameters of 22,36,50 and 75 mm were constructed.The tests were carried out on these setups at different loading rates,and the specimens had the same diameter of elastic bars and same ratio of length to diameter.The test results show that the larger the elastic bar's diameter is,the less the loading rate is needed to cause specimen failure,they show good power relationship,and that under the same strain rate loading,specimens are broken more seriously with larger diameter SHPB setup than with smaller one.
基金This work was supported by the Natural Science Foundation of Shannxi Province,China(2021JQ-947)the China Postdoctoral Science Fund(2019M653785)+1 种基金The author Dr.Cao is very grateful for the support received from the Young Scientists Fund of the National Natural Science Foundation of China[grant number 51904332]Natural Science Foundation of Shannxi Province,China[grant number 2020JQ-934].
文摘The split-Hopkinson pressure bar(SHPB)is a widely used experimental technique for studying the mechanical properties of materials at high strain rates.There are two kinds of loading methods applied in the SHPB technique,namely one-side loading and symmetric loading.However,the experimental accuracy of the two loading methods is affected by the interface contact.The present study focused on the inadequate contact caused by the misalignment of the pressure bars.The commercial software ABAQUS was used for simulations.The result shows that the inadequate contact caused by the alignment of the bars has a non-negligible effect on the calculated results.Compared with the one-side loading Hopkinson pressure bar,the symmetric loading Hopkinson pressure bar has a more relaxed requirement for the alignment of the bars.The conclusion arrived at in this paper can help researchers to make a reasonable choice between one-side and symmetric loading Hopkinson pressure bars according to actual requirements.
文摘A hull structure is prone to local deformation and damage due to the pressure load on the surface.How to simulate surface pressure is an important issue in ship structure test.The loading mode of hydraulic actuator combined with high-pressure flexible bladder was proposed,and the numerical model of the loading device based on flexible bladder was established.The design and analysis method of high-pressure flexible bladder based on aramid-fiber reinforced thermoplastic polyurethane was proposed to break through the surface pressure loading technology of ship structures.The surface pressure loading system based on flexible bladder was developed.The ultimate strength verification test of the box girder under the combined action of bending moment and pressure was carried out to systematically verify the feasibility and applicability of the loading system.The results show that the surface pressure loading technology can be used well for applying uniform pressure to ship structures.Compared with the traditional surface loading methods,the improved device can be applied with horizontal constant pressure load,with rapid response and safe process,and the pressure load is always stable with the increase of the bending moment load during the test.The requirement for uniform loading in the comprehensive strength test of large structural models is satisfied and the accuracy of the test results is improved by this system.
基金the State Key Laboratory of Coal Resources and Safe Mining,China University of Mining and Technology(No.SKLCRSM22KF011)the National Natural Science Foundation of China(Nos.52130411,52104191,51974120,and 51904103)+1 种基金the Natural Science Foundation of Hunan Province(No.2021JJ40204)the Science and Technology Innovation Program of Hunan Province(No.2020RC3047).
文摘The study of pressure stimulated current(PSC)changes of rocks is significant to monitor dynamic disasters in mines and rock masses.The existing studies focus on change laws and mechanism of currents generated under the loading of rocks.An electrical and mechanics test system was established in this paper to explore the impacts of loading rates on PSCs.The results indicated that PSC curves of different rocks had different change laws under low/high loading rates.When the loading rate was relatively low,PSC curves firstly changed gently and then increased exponentially.Under high loading rates,PSC curves experienced the rapid increase stage,gentle increase stage and sudden change stage.The compressive strength could greatly affect the peak PSC in case of rock failure.The loading rate was a key factor in average PSC.Under low loading rates,the variations of PSCs conformed to the damage charge model of fracture mechanics,while they did not at the fracture moment.Under high loading rates,the PSCs at low stress didn’t fit the model due to the stress impact effects.The experimental results could provide theoretical basis for the influence of loading rates on PSCs.
基金Projects(51174228,51174088,51204068,51274097)supported by the National Natural Science Foundation of China
文摘To reveal the water inrush mechanics of underground deep rock mass subjected to dynamic disturbance such as blasting, compression-shear rock crack initiation rule and the evolution of crack tip stress intensity factor are analyzed under static-dynamic loading and seepage water pressure on the basis of theoretical deduction and experimental research. It is shown that the major influence factors of the crack tip stress intensity factor are seepage pressure, dynamic load, static stress and crack angle. The existence of seepage water pressure aggravates propagation of branch cracks. With the seepage pressure increasing, the branch crack experiences unstable extension from stable propagation. The dynamic load in the direction of maximum main stress increases type I crack tip stress intensity factor and its influence on type II crack intensity factor is related with crack angle and material property. Crack initiation angle changes with the dynamic load. The initial crack initiation angle of type I dynamic crack fracture is 70.5°. The compression-shear crack initial strength is related to seepage pressure, confining pressure, and dynamic load. Experimental results verify that the initial crack strength increases with the confining pressure increasing, and decreases with the seepage pressure increasing.
基金supported by The Key Project of National Natural Science Foundation of China(Grant Nos.50639010 and 50909039)
文摘The characteristics of dynamic stress in the seabed under wave loading are constant principal stress and continuous rotation of the principal stress direction. Cyclic triaxial-torsional coupling shear tests were pefformed on saturated silt by the hollow cylinder apparatus under different relative densities, deviator stress ratios and vibration frequencies to study the development of pore water pressure of the saturated silt under wave loading. It was found that the development of pore water pressure follows the trend of ＂fast - steady - drastic＂. The turning point from fast to steady stage is not affected by relative density and deviator stress ratio. However, the turning point from steady to drastic stage relies on relative density and deviator stress ratio. The vibration cycle for the liquefaction of saturated silt decreases with increasing deviator stress ratio and increases with relative density. The vibration cycle for the liquefaction of the saturated silt increases with vibration frequency and reaches a peak value, after which it decreases with increasing vibration frequency for the relative density of 70%. But the vibration cycle for the liquefaction of saturated silt increases with vibration frequency for the relative density of 30%. The development of pore water pressure of the saturated silt is influenced by relative density and vibration frequency.
基金funding support from National Natural Science Foundation of China(Grant No.52179109)Jiangsu Provincial Natural Science Foundation(Grant No.BK20230967)Open Research Fund of State Key Laboratory of Mechanical Behavior and System Safety of Traffic Engineering Structures,Shijiazhuang Tiedao University(Grant No.KF2022-02).
文摘Existing studies have focused on the behavior of the retaining wall equipped with expanded polystyrene(EPS)geofoam inclusions under semi-infinite surcharge loading rather than limited surcharge loading.In this paper,the failure mode and the earth pressure acting on the rigid retaining wall with EPS geofoam inclusions and granular backfills(henceforth referred to as EPS-wall),under limited surcharge loading are investigated through two-and three-dimensional model tests.The testing results show that different from the sliding of almost all the backfill in the EPS-wall under semi-infinite surcharge loading,only an approximately triangular backfill slides in the wall under limited surcharge loading.The distribution of the lateral earth pressure on the EPS-wall under limited surcharge loading is non-linear,and the distribution changes from the increase of the wall depth to the decrease with the increase of the limited surcharge loading.An approach based on the force equilibrium of a differential element is developed to predict the lateral earth pressure behind the EPS-wall subjected to limited surcharge loading,and its performance was fully validated by the three-dimensional model tests.
基金the National Natural Science Foundation of China(Nos.52374218,52174122 and 52374094)Outstanding Youth Fund of Shandong Natural Science Foundation(No.ZR2022YQ49)Taishan Scholar Project in Shandong Province(Nos.tspd20210313 and tsqn202211150).
文摘With the increase of underground engineering construction depth,the phenomenon of surrounding rock sudden failure caused by supporting structure failure occurs frequently.The conventional unloading con-fining pressure(CUCP)test cannot simulate the plastic yielding and instantaneous unloading process of supporting structure to rock.Thus,a high stress loading-instantaneous unloading confining pressure(HSL-IUCP)test method was proposed and applied by considering bolt’s fracture under stress.The wall thickness of confining pressure plates and the material of bolts were changed to realize different confin-ing pressure loading stiffness(CPLS)and lateral maximum allowable deformation(LMAD).The superio-rity of HSL-ICPU method is verified compared with CUCP.The rock failure mechanism caused by sudden failure of supporting structure is obtained.The results show that when CPLS increases from 1.35 to 2.33 GN/m,rock’s peak strength and elastic modulus increase by 25.18%and 23.70%,respectively.The fracture characteristics change from tensile failure to tensile-shear mixed failure.When LMAD decreases from 0.40 to 0.16 mm,rock’s residual strength,peak strain,and residual strain decrease by 91.80%,16.94%,and 21.92%,respectively,and post-peak drop modulus increases by 140.47%.The test results obtained by this method are closer to rock’s real mechanical response characteristics compared with CUCP.
文摘Hemispherical asymmetry in core dynamics induces degree-1 pressure variations at the core mantle boundary （CMB）, which in turn deforms the overlaying elastic mantle, at the same time keeps center of mass of the whole Earth stationary in space. We develop a systematic procedure to deal with the degree-1 CMB pressure loading. We find by direct calculation a surprisingly negative load Love number h1=-1.425 for vertical displacement. Further analysis indicates that the negative hi corre- sponds to thickening above the positive load that defies intuition that pressure inflation pushes over- laying material up and thins the enveloping shell. We also redefine the pressure load Love numbers in general to enable comparison between the surface mass load and the CMB pressure load for the whole spectrum of harmonic degrees. We find that the gravitational perturbations from the two kinds of loads at degrees n〉l are very similar in amplitude but opposite in sign. In particular, if the CMB pressure variation at degree 2 is at the level of -1 hpa/yr （1 cm water height per year）, it would perturb the variation of Earth＇s oblateness, known as the J2, at the observed level.
文摘A quasi-static/dynamic pressure-tension compound loading system was established in this paper for the research of cellular mechanical circumstances. Both radical and circumferential strain of the basement membrane were studied and compared in theoretical calculations by using the FEA Software ABAQUS and experimental measurements. The tension of the basement membrane was studied both in ABUQUES results and experimental results, the relation between the height of the concave cavity, the radius of the membrane and the strain of the membrane were studied in details.
文摘Skin integrity breakdown and pressure ulcer formation on the heel are predictable and preventable healthcare occurrences. By minimizing surface contact pressures that can cause heel capillary occlusion, heel off-loading devices help mitigate the risk of decubitus ulceration. The purpose of this study is to investigate the efficacy of six off-loading methods commonly used in clinical settings to decrease heel contact pressure. Pressure mapping is used to evaluate contact pressure at the heel for underweight, normal weight, and overweight simulations. Based upon averages across four trials, it is shown that all devices reduce heel contact pressure when compared to no off-load- ing. The PRUventor™ boot exhibits significantly lower average pressure values than other off-load- ing strategies tested, suggesting that the PRUventor™ is the most effective off-loading device. From the analysis of the experimental data and comparison to similar data for respective off-loading alternatives, it is concluded that the PRUventor™ boot is an effective heel off-loading device for use in clinical settings.
基金supported by National Key Technology R&D Program of China under the 11th Five-year(Grant No.2006BAK02B02),and China Special Equipment Science & Technology Cooperation Platform
文摘By increasing the yield strengths of austenitic stainless steels for pressure vessels with strain hardening techniques,the elastic load bearing capacity of austenitic stainless steel pressure vessels can be significantly improved.Two kinds of strain hardening methods are often used for austenitic stainless steel pressure vessels：Avesta model for ambient temperature applications and Ardeform model for cryogenic temperature applications.Both methods are obtained from conventional design rules based on the linear elastic theory,and only consider the hardening effect from materials.Consequently this limits the applications of strain hardening techniques for austenitic stainless steel pressure vessels because of safety concerns.This paper investigates the effect of strain hardening on the load bearing capacity of austenitic stainless steel pressure vessels under large deformation,based on the elastic-plastic theory.Firstly,to understand the effect of strain hardening on material behavior,the plastic instability loads of a round tensile bar specimen are derived under two different loading paths and validated by experiments.Secondly,to investigate the effect of strain hardening on pressure vessels strength, the plastic instability pressure under strain hardening is derived and further validated by finite element simulations.Further,the safety margin of pressure vessels after strain hardening is analyzed by comparing the safety factor values calculated from bursting tests,finite element analyses,and standards.The researching results show that the load bearing capacity of pressure vessels at ambient temperature is independent of the loading history when the effects of both material strain hardening and structural deformation are considered.Finite element simulations and bursting tests results show that the minimum safety factor of austenitic stainless steel pressure vessels with 5% strain hardening is close to the recommended value for common pressure vessels specified in the European pressure vessel standard.The proposed study also shows that in the strain hardening design of austenitic stainless steel pressure vessels,the calculation for plastic instability pressure could use theoretical formula or finite element analyses based on geometrical dimensions and material property parameters before strain hardening,but a 5%strain should be employed as a design limit.The proposed research can be used for the strain hardening design of austenitic stainless steel pressure vessels safely.
基金Projects(2013CB036004, 2011CB013800) supported by the National Basic Research Program of ChinaProject(51178468, 50908234) supported by the National Natural Science Foundation of ChinaProject(2011G103-B) supported by the Science and Technology Development of Railway in China
文摘According to the interaction of three shallow tunnels with large section, the analytical solution to rock pressure has been derived and discussed. The load model is given when the bilateral tunnels are excavated. According to the model, the stresses of three tunnels and single tunnel are calculated and compared to analyze the distribution characteristics, where the stresses are influenced by controlling factors of clear distance, covering depth and inclination angle of ground surface. The results show that, in general, the bias distribution is more serious. Therefore, it is significant to settle down the load model of three shallow tunnels so as to determine the measure of reinforcement and design the structure of support. The model and results can be used as a theoretical basis in designation and further research of the three shallow tunnels.
基金the financial support from the China Postdoctoral Science Foundation(Nos.2022M713384,and 2022M721450)the National Natural Science Foundation of China(Nos.52174187,51704164,and 52130409)the Technology Innovation Fund of China Coal Research Institute(No.2020CX-I-07).
文摘Coal and gas outbursts are dynamic disasters in which a large mass of gas and coal suddenly emerges in a mining space within a split second.The interaction between the gas pressure and stress environment is one of the key factors that induce coal and gas outbursts.In this study,first,the coupling relationship between the gas pressure in the coal body ahead of the working face and the dynamic load was investigated using experimental observations,numerical simulations,and mine-site investigations.It was observed that the impact rate of the dynamic load on the gas-bearing coal can significantly change the gas pressure.The faster the impact rate,the speedier the increase in gas pressure.Moreover,the gas pressure rise was faster closer to the impact interface.Subsequently,based on engineering background,we proposed three models of stress and gas pressure distribution in the coal body ahead of the working face:static load,stress disturbance,and dynamic load conditions.Finally,the gas pressure distribution and outburst mechanism were investigated.The high concentration of gas pressure appearing at the coal body ahead of the working face was caused by the dynamic load.The gas pressure first increased gradually to a peak value and then decreased with increasing distance from the working face.The increase in gas pressure plays a major role in outburst initiation by resulting in the ability to more easily reach the critical points needed for outburst initiation.Moreover,the stronger the dynamic load,the greater the outburst initiation risk.The results of this study provide practical guidance for the early warning and prevention of coal and gas outbursts.
基金Project (No. X106871) supported by the Natural Science Foundation of Zhejiang Province,China
文摘With von Mises yield criterion,the loading range of Net Section Collapse(NSC) Criteria is extended from combined tension and bending loadings to combined bending,torsion and internal pressure loadings.A new theoretical analyzing method of plastic limit load for pressure pipe with incomplete welding defects based on the extended NSC Criteria is presented and the correlative formulas are deduced,the influences of pipe curvature,circumferential length and depth of incomplete welding defects on the plastic limit load of pressure pipe are considered as well in this method.Meanwhile,according to the orthogonal experimental design method,the plastic limit loads are calculated by the finite element method and compared with the theoretical values.The results show that the expressions of plastic limit load of pressure pipe with incomplete welding defects under bending,torsion and internal pressure based on extended NSC criteria are reliable.The study provides an important theoretical basis for the establishment of safety assessment measure towards pressure pipe with incomplete welding defects.
