In the realm of nonlinear integrable systems,the presence of decompositions facilitates the establishment of linear superposition solutions and the derivation of novel coupled systems exhibiting nonlinear integrabilit...In the realm of nonlinear integrable systems,the presence of decompositions facilitates the establishment of linear superposition solutions and the derivation of novel coupled systems exhibiting nonlinear integrability.By focusing on single-component decompositions within the potential BKP hierarchy,it has been observed that specific linear superpositions of decomposition solutions remain consistent with the underlying equations.Moreover,through the implementation of multi-component decompositions within the potential BKP hierarchy,successful endeavors have been undertaken to formulate linear superposition solutions and novel coupled Kd V-type systems that resist decoupling via alterations in dependent variables.展开更多
Multi-component transition group metal borides(MMB_(2))have become a research hotspot due to their new composition design concepts and superior properties compared with conventional ceramics.Most of the current method...Multi-component transition group metal borides(MMB_(2))have become a research hotspot due to their new composition design concepts and superior properties compared with conventional ceramics.Most of the current methods,however,are complicated and time-consuming,the mass production remains a chal-lenge.Herein,we proposed a new high-efficiency strategy for synthesis of MMB_(2)using molten aluminum as the medium for the first time.The prepared Al-containing multi-component borides(TiZrHfNbTa)B_(2)microcrystals had a homogeneous composition with a hexagonal AlB_(2)structure and ultra-high hardness value of∼35.3 GPa,which was much higher than data reported in the literature and the rule of mix-ture estimations.Furthermore,combined with the First-principles calculation results,we found that the Poisson’s ratio(v)values exhibit a clearly ascending trend from 0.17 at VEC=3.5 to 0.18 at VEC=3.4,then to 0.201 at VEC=3.2 with the increasing of Al content.This indicates that the intrinsic toughness of multi-component boride microcrystals is obviously enhanced by the trace-doped Al elements.Besides,the fabricated Al-containing multi-component boride microcrystals have superior oxidation activation en-ergy and structural stability.The enhanced oxidation resistance is mainly attributed to the formation of a protective Al2 O3 oxide layer and the lattice distortion,both of which lead to sluggish diffusion of O_(2).These findings propose a new unexplored avenue for the fabrication of MMB_(2)materials with supe-rior comprehensive performance including ultra-hardness and intrinsically improved thermo-mechanical properties.展开更多
A convenient photocatalytic multi-component reaction of alkenes,quinoxalin-2(1H)-ones,and diazo compounds has been developed in the presence of water.A number of ester-containing quinoxalin-2(1H)-ones could be efficie...A convenient photocatalytic multi-component reaction of alkenes,quinoxalin-2(1H)-ones,and diazo compounds has been developed in the presence of water.A number of ester-containing quinoxalin-2(1H)-ones could be efficiently obtained in moderate to good yields at room temperature.This metal-free visiblelight-driven tandem reaction was conducted through proton-coupled electron transfer(PCET)process using water as the hydrogen donor and 1,2,3,5-tetrakis(carbazol-9-yl)-4,6-dicyanobenzene(4CzIPN)as the photocatalyst.展开更多
A multi-component system has the long fixed maintenance time, so the opportunistic maintenance policy is adopted to put preventive replacement and corrective replacement together, so that the long fixed maintenance ti...A multi-component system has the long fixed maintenance time, so the opportunistic maintenance policy is adopted to put preventive replacement and corrective replacement together, so that the long fixed maintenance time can be shared by more than one component, and the system availability can be improved. Then, the generation characteristics of the random failure time are researched based on the replacement maintenance and the minima[ maintenance. Furthermore, by choosing the opportunistic replacement ages of each component as opti- mized variables, a simulation algorithm based on an opportunistic maintenance policy is designed to maximize the total availability. Finally, the simulation result shows the validity of the algorithm by an example.展开更多
This review focuses on the recent research progress in the multi-component assembly of luminescent rare earth hybrid materials, which is based on the luminescent rare earth compounds and two or more other building uni...This review focuses on the recent research progress in the multi-component assembly of luminescent rare earth hybrid materials, which is based on the luminescent rare earth compounds and two or more other building units, including the other photoactive species. It covers the multi-component luminescent rare earth hybrids which was assembled with different(a) organic-inorganic polymeric units,(b)nanoporous units,(c) nanoparticle composites or(d) other developing special units. Finally, future challenges and opportunities in this field are discussed. Herein it mainly focuses on the work of Yan's group in recent years.展开更多
A general scheme for generating a multi-component integrable equation hierarchy is proposed. A simple 3M- dimensional loop algebra ~X is produced. By taking advantage of ~X a new isospectral problem is established and...A general scheme for generating a multi-component integrable equation hierarchy is proposed. A simple 3M- dimensional loop algebra ~X is produced. By taking advantage of ~X a new isospectral problem is established and then by making use of the Tu scheme the multi-component Dirac equation hierarchy is obtained. Finally, an expanding loop algebra ~FM of the loop algebra ~X is presented. Based on the ~FM, the multi-component integrable coupling system of the multi-component Dirac equation hierarchy is investigated. The method in this paper can be applied to other nonlinear evolution equation hierarchies.展开更多
Seismic AVO analysis now is one of the major criteria for recognizing potential hydrocarbon reservoirs. Volume scattering information that carries information of stratigraphic structure, lithology, and pore fluid is m...Seismic AVO analysis now is one of the major criteria for recognizing potential hydrocarbon reservoirs. Volume scattering information that carries information of stratigraphic structure, lithology, and pore fluid is more useful for seismic exploration. However, traditional AVO analysis is based on the Zoeppritz equation, which only contains single-interface information. Quantitative interpretation of the thin bed thickness is essential to thin bed structure interpretation, reservoir description, and lateral reservoir prediction. The reflectance spectrum equation based on the elastic wave propagation matrix in the frequency domain derived in this paper shows that both interfaces and intervals have an effect on amplitude. The equation includes information about both single interfaces and volume scattering. Since the reflectance spectrum equation is a continuous function of thin bed thickness and frequency, it is convenient to analyze the effects of a single frequency and bed thickness on the reflectance spectrum. Bed thickness is analyzable until the bed thickness is vanishingly small. These characteristics can＇t be achieved by Fourier transform. The propagation of seismic waves is complex and various wave modes exist simultaneously. The reflectance spectrum includes various propagating wave modes and multiples and is better for simulating multi-component thin bed AVO responses than the ray tracing method.展开更多
The conventional digital core models are usually small in size and have difficulty in representing the complex structures of heterogeneous rocks;Therefore,the parameters of simulated rock physics are difficult to be r...The conventional digital core models are usually small in size and have difficulty in representing the complex structures of heterogeneous rocks;Therefore,the parameters of simulated rock physics are difficult to be referenced.In this study,we propose a feasible simulation method for obtaining multi-scale and multi-component digital cores based on three types of sandstone samples.In the proposed method,the plug and subplug samples are scanned via micro-computed tomography at different resolutions.Furthermore,the images are precisely registered using the proposed hybrid image registration method.In case of high-resolution images,the traditional segmentation method is used to segment the cores into pores and minerals.Subsequently,we established the relations between the gray values and the porosity/mineral content in case of the low-resolution images based on the registered domains and the relation curves were applied to the segmentation of the low-resolution images.The core images constitute the multi-scale and multi-component digital core models after segmentation.Further,the elastic properties of the three samples were simulated at both fine and coarse scales based on the multi-scale and multi-component digital core models,and four component models were considered.The results show that the multi-scale and multi-component digital core models can overcome the representative limits of the conventional digital core models and accurately characterize pores and minerals at different scales.The numerical results of the elastic modulus are more representative at large scales,and considerably reliable results can be obtained by appropriately considering the minerals.展开更多
The influence of melt superheating treatment on the solid/liquid （S/L） interface morphology of directionally solidified Ni-based superalloy DZ125 is investigated to elucidate the relationship between melt characteri...The influence of melt superheating treatment on the solid/liquid （S/L） interface morphology of directionally solidified Ni-based superalloy DZ125 is investigated to elucidate the relationship between melt characteristic and S/L interface stability. The results indicate that the interface morphology is not only related to the withdrawal velocity （R） but also to the melt superheating temperature （Ts） when the thermal gradient of solidification interface remains constant for different Ts with appropriate superheating treatment regulation. The interface morphology changes from cell to plane at R of 1.1 μm/s when Ts increases from 1500°C to 1650°C, and maintains plane with further elevated Ts of 1750°C. However, the interface morphology changes from coarse dendrite to cell and then to cellular dendrite at R of 2.25 μm/s when Ts increases from 1500°C to 1650°C and then to 1750°C. It is proved that the solidification onset temperature and the solidification interval undergo the nonlinear variation when Ts increases from 1500°C to 1680°C, and the turning point is 1650°C at which the solidification onset temperature and the solidification interval are all minimum. This indicates that the melt superheating treatment enhances the solidification interface stability and has important effect on the solidification characteristics.展开更多
Aiming at wind turbines,the opportunistic maintenance optimization is carried out for multi-component system,where minimal repair,imperfect repair,replacement as well as their effects on component’s effective age are...Aiming at wind turbines,the opportunistic maintenance optimization is carried out for multi-component system,where minimal repair,imperfect repair,replacement as well as their effects on component’s effective age are considered.At each inspection point,appropriate maintenance mode is selected according to the component’s effective age and its maintenance threshold.To utilize the maintenance opportunities for the components among the wind turbines,opportunistic maintenance approach is adopted.Meanwhile,the influence of seasonal factor on the component’s failure rate and improvement factor’s decrease with the increase of repair’s times are also taken into account.The maintenance threshold is set as the decision variable,and an opportunistic maintenance optimization model is proposed to minimize wind turbine’s life-cycle maintenance cost.Moreover,genetic algorithm is adopted to solve the model,and the effectiveness is verified with a case study.The results show that based on the component’s inherent reliability and maintainability,the proposed model can provide optimal maintenance plans accordingly.Furthermore,the higher the component’s reliability and maintainability are,the less the times of repair and replacement will be.展开更多
To improve the mainlainability design efficiency and quality, a layout optimization method for maintainability of multi-component systems was proposed. The impact of the component layout design on system maintainabili...To improve the mainlainability design efficiency and quality, a layout optimization method for maintainability of multi-component systems was proposed. The impact of the component layout design on system maintainability was analyzed, and the layout problem for maintainability was presented. It was formulated as an optimization problem, where maintainability, layout space and distance requirement were formulated as objective functions. A multi-objective particle swarm optimization algorithm, in which the constrained-domination relationship and the update strategy of the global best were simply modified, was then used to obtain Pareto optimal solutions for the maintainability layout design problem. Finally, application in oxygen generation system of a spacecraft was studied in detail to illustrate the effectiveness and usefulness of the proposed method. The results show that the concurrent maintainability design can be carried out during the layout design process by solving the layout optimization problem for maintainability.展开更多
Elastic waves are affected by viscoelasticity during the propagation through the Earth,resulting in energy attenuation and phase distortion,in turn resulting in low seismic imaging accuracy.Therefore,viscoelasticity s...Elastic waves are affected by viscoelasticity during the propagation through the Earth,resulting in energy attenuation and phase distortion,in turn resulting in low seismic imaging accuracy.Therefore,viscoelasticity should be considered in seismic migration imaging.We propose a Q compensated multicomponent elastic Gaussian beam migration(Q-EGBM)method to(1)separate the elastic-wave data into longitudinal(P)and transverse(S)waves to perform PP-wave and PS-wave imaging;(2)recover the amplitude loss caused by attenuation;(3)correct phase distortions caused by dispersion;(4)improve the resolution of migration imaging.In this paper,to accomplish(2),(3),and(4),we derive complex-valued traveltimes in viscoelastic media.The results of numerical experiments using a simple five-layer model and a sophisticated BP gas model show that the method presented here has significant advantages in recovering energy decay and correcting phase distortion,as well as significantly improving imaging resolution.展开更多
In the present study, a method for the quantitative analysis of multi-components by single marker(QAMS) has been developed and validated for the simultaneous determination of echinacoside(ECH), tubuloside A, acteoside...In the present study, a method for the quantitative analysis of multi-components by single marker(QAMS) has been developed and validated for the simultaneous determination of echinacoside(ECH), tubuloside A, acteoside, isoacteoside, and2’-acetylacteoside in Cistanches Herba. ECH was used as the internal standard(IS) to obtain the relative correction factors(RCFs) of the other four phenylethanoid glycosides(PhGs);meanwhile, various influencing factors on RCFs were investigated under different conditions. The content of each component was calculated with RCF. The results were compared with those obtained by the external standard method(ESM) to verify the feasibility and accuracy of the established QAMS method. No significant difference was found in the quantitative results of 10 batches of Cistanches Herba between QAMS and ESM. The proposed QAMS method for simultaneous determination of PhGs in Cistanches Herba is accurate and feasible, providing an efficient and economical approach for the quality control of Cistanches Herba.展开更多
Multi-component alloys have demonstrated excellent performance in various applications,but the vast range of possible compositions and microstructures makes it challenging to identify optimized alloys for specific pur...Multi-component alloys have demonstrated excellent performance in various applications,but the vast range of possible compositions and microstructures makes it challenging to identify optimized alloys for specific purposes.To overcome this challenge,large-scale atomic simulation techniques have been widely used for the design and optimization of multi-component alloys.The capability and reliability of large-scale atomic simulations essentially rely on the quality of interatomic potentials that describe the interactions between atoms.This work provides a comprehensive summary of the latest advances in atomic simulation techniques for multi-component alloys.The focus is on interatomic potentials,including both conventional empirical potentials and newly developed machine learning potentials(MLPs).The fitting processes for different types of interatomic potentials applied to multi-component alloys are also discussed.Finally,the challenges and future perspectives in developing MLPs are thoroughly addressed.Overall,this review provides a valuable resource for researchers interested in developing optimized multicomponent alloys using atomic simulation techniques.展开更多
The segregation modes and characteristics of 1-6 mm multi-component lignite were studied in a microporous, vibrated, gas-fluidized bed of Φ110 mm ×400 mm. The effects of particle density and size, vibration freq...The segregation modes and characteristics of 1-6 mm multi-component lignite were studied in a microporous, vibrated, gas-fluidized bed of Φ110 mm ×400 mm. The effects of particle density and size, vibration frequency and amplitude, and gas velocity on these characteristics were considered. The average size, average density, size deviation coefficient, and density deviation coefficient were used to identify lignite size and density. The separation efficiency was adopted to evaluate the segregation performance,and the segregation mechanisms were explored. The results show that ε(size,max) of heterogeneous multisize-component lignite with K_(size) = 65% reaches 80% at f= 20 Hz, A = 5 mm, and N =(1,3). ε_(density,max) Of heterogeneous multi-density-component lignite with K_(density)= 25% reaches 50% at f = 15 Hz, A = 5 mm,and N =(1,1.5). The density segregations of 1-3 and 3-6 mm multi-component mixtures are remarkable,ε_(density,max)= 42% and 31% at f= 14 and 16 Hz, and A = 3 and 5 mm, respectively. The size segregation of 1-6 mm multi-component mixture is prominent and ε_(size,max)= 55% at f= 15 Hz, A = 5 mm. The mediumsized mixture with a narrow size distribution at low frequency is favorable for density segregation,and a mixture with a wider size distribution at high frequency is most favorable for size segregation.Precise control of gas flow and vibration as well as optimal design of the fluidized bed can improve the performance of segregation in the vibrated gas-fluidized bed.展开更多
Although opportunistic maintenance strategies are widely used for multi-component systems, all opportunistic mainte- nance strategies only consider economic dependence and do not take structural dependence into accoun...Although opportunistic maintenance strategies are widely used for multi-component systems, all opportunistic mainte- nance strategies only consider economic dependence and do not take structural dependence into account. An opportunistic main- tenance strategy is presented for a multi-component system that considers both structural dependence and economic dependence. The cost relation and time relation among components based on structural dependence are developed. The maintenance strategy for each component of a multi-component system involves one of five maintenance actions, namely, no-maintenance, a minimal maintenance action, an imperfect maintenance action, a perfect maintenance action, and a replacement action. The maintenance action is determined by the virtual age of the component, the life expectancy of the component, and the age threshold values. Monte Carlo simulation is designed to obtain the optimal oppor- tunistic maintenance strategy of the system over its lifetime. The simulation result reveals that the minimum maintenance cost with a strategy that considers structural dependence is less than that with a strategy that does not consider structural dependence. The availability with a strategy that considers structural dependence is greater than that with a strategy that does not consider structural dependence under the same conditions.展开更多
Complex repairable system is composed of thousands of components.Some maintenance management and decision problems in maintenance management and decision need to classify a set of components into several classes based...Complex repairable system is composed of thousands of components.Some maintenance management and decision problems in maintenance management and decision need to classify a set of components into several classes based on data mining.Furthermore,with the complexity of industrial equipment increasing,the managers should pay more attention to the key components and carry out the lean management is very important.Therefore,the idea"customer segmentation"of"precise marketing"can be used in the maintenance management of the multi-component system.Following the idea of segmentation,the components of multicomponent systems should be subdivied into groups based on specific attributes relevant to maintenance,such as maintenance cost,mean time between failures,and failure frequency.For the target specific groups of parts,the optimal maintenance policy,health assessment and maintenance scheduling can be determined.The proposed analysis framework will be given out.In order to illustrate the effectiveness of this method,a numerical example is given out.展开更多
For unacceptable computational efficiency and accuracy on the probabilistic analysis of multi-component system with multi-failure modes,this paper proposed multi-extremum response surface method(MERSM).MERSM model was...For unacceptable computational efficiency and accuracy on the probabilistic analysis of multi-component system with multi-failure modes,this paper proposed multi-extremum response surface method(MERSM).MERSM model was established based on quadratic polynomial function by taking extremum response surface model as the sub-model of multi-response surface method.The dynamic probabilistic analysis of an aeroengine turbine blisk with two components,and their reliability of deformation and stress failures was obtained,based on thermal-structural coupling technique,by considering the nonlinearity of material parameters and the transients of gas flow,gas temperature and rotational speed.The results show that the comprehensive reliability of structure is 0.9904 when the allowable deformations and stresses of blade and disk are 4.78×10–3 m and 1.41×109 Pa,and 1.64×10–3 m and 1.04×109 Pa,respectively.Besides,gas temperature and rotating speed severely influence the comprehensive reliability of system.Through the comparison of methods,it is shown that the MERSM holds higher computational precision and speed in the probabilistic analysis of turbine blisk,and MERSM computational precision satisfies the requirement of engineering design.The efforts of this study address the difficulties on transients and multiple models coupling for the dynamic probabilistic analysis of multi-component system with multi-failure modes.展开更多
On the basis of a multi-length scale modeling, a mixture-averaged multi-component/multiphase micro- segregation model was proposed without pre-set function for the micro-scale solute profile. The model explains the ef...On the basis of a multi-length scale modeling, a mixture-averaged multi-component/multiphase micro- segregation model was proposed without pre-set function for the micro-scale solute profile. The model explains the effect of morphologies of solidifying phases and solid back diffusion （SBD） on segregation, and covers the two limiting solidification cases of Scheil and Lever-rule models. A commercial Thermo-Calc software package/database was linked to the algorithms via its TQ6-interface for instantaneous determination of the related thermodynamic data of the multi-component alloys. The influences of cooling rate and other parameters on the solidification path and micro-segregation behavior were numerically investigated by sample calculation of the ternary AI-Cu-Mg alloys. A parallel experimental investigation on AI-Cu-Si alloys solidified under different cooling conditions was conducted to validate the theoretical model. Reasonable agreements were gained between the predicted solidification paths and the measured results.展开更多
A three component one-pot protocol was investigated for the synthesis of methylene bis isoxazolo[4,5-b]-pyridine-N-oxides from commercially available materials.
基金sponsored by the National Natural Science Foundations of China under Grant Nos.12301315,12235007,11975131the Zhejiang Provincial Natural Science Foundation of China under Grant No.LQ20A010009。
文摘In the realm of nonlinear integrable systems,the presence of decompositions facilitates the establishment of linear superposition solutions and the derivation of novel coupled systems exhibiting nonlinear integrability.By focusing on single-component decompositions within the potential BKP hierarchy,it has been observed that specific linear superpositions of decomposition solutions remain consistent with the underlying equations.Moreover,through the implementation of multi-component decompositions within the potential BKP hierarchy,successful endeavors have been undertaken to formulate linear superposition solutions and novel coupled Kd V-type systems that resist decoupling via alterations in dependent variables.
基金financially supported by the National Natural Science Foundation of China(Nos.52271033 and 52071179)the Key program of National Natural Science Foundation of China(No.51931003)+2 种基金Natural Science Foundation of Jiangsu Province,China(No.BK20221493)Jiangsu Province Leading Edge Technology Basic Research Major Project(No.BK20222014)Foundation of“Qinglan Project”for Colleges and Universities in Jiangsu Province.
文摘Multi-component transition group metal borides(MMB_(2))have become a research hotspot due to their new composition design concepts and superior properties compared with conventional ceramics.Most of the current methods,however,are complicated and time-consuming,the mass production remains a chal-lenge.Herein,we proposed a new high-efficiency strategy for synthesis of MMB_(2)using molten aluminum as the medium for the first time.The prepared Al-containing multi-component borides(TiZrHfNbTa)B_(2)microcrystals had a homogeneous composition with a hexagonal AlB_(2)structure and ultra-high hardness value of∼35.3 GPa,which was much higher than data reported in the literature and the rule of mix-ture estimations.Furthermore,combined with the First-principles calculation results,we found that the Poisson’s ratio(v)values exhibit a clearly ascending trend from 0.17 at VEC=3.5 to 0.18 at VEC=3.4,then to 0.201 at VEC=3.2 with the increasing of Al content.This indicates that the intrinsic toughness of multi-component boride microcrystals is obviously enhanced by the trace-doped Al elements.Besides,the fabricated Al-containing multi-component boride microcrystals have superior oxidation activation en-ergy and structural stability.The enhanced oxidation resistance is mainly attributed to the formation of a protective Al2 O3 oxide layer and the lattice distortion,both of which lead to sluggish diffusion of O_(2).These findings propose a new unexplored avenue for the fabrication of MMB_(2)materials with supe-rior comprehensive performance including ultra-hardness and intrinsically improved thermo-mechanical properties.
基金supported by Sichuan Science and Technology Program(No.2023NSFSC0101)the 2024 Provincial platform project of Chengdu Normal University(No.GNFZ202404)+1 种基金Natural Science Foundation of Shandong Province(No.ZR2021MB065)National Natural Science Foundation of China(No.22101237)。
文摘A convenient photocatalytic multi-component reaction of alkenes,quinoxalin-2(1H)-ones,and diazo compounds has been developed in the presence of water.A number of ester-containing quinoxalin-2(1H)-ones could be efficiently obtained in moderate to good yields at room temperature.This metal-free visiblelight-driven tandem reaction was conducted through proton-coupled electron transfer(PCET)process using water as the hydrogen donor and 1,2,3,5-tetrakis(carbazol-9-yl)-4,6-dicyanobenzene(4CzIPN)as the photocatalyst.
文摘A multi-component system has the long fixed maintenance time, so the opportunistic maintenance policy is adopted to put preventive replacement and corrective replacement together, so that the long fixed maintenance time can be shared by more than one component, and the system availability can be improved. Then, the generation characteristics of the random failure time are researched based on the replacement maintenance and the minima[ maintenance. Furthermore, by choosing the opportunistic replacement ages of each component as opti- mized variables, a simulation algorithm based on an opportunistic maintenance policy is designed to maximize the total availability. Finally, the simulation result shows the validity of the algorithm by an example.
基金Project supported by the National Natural Science Foundation of China(21571142)the Developing Science Fund of Tongji University,the Natural Science Foundation of Zhejiang Province(LQ14B010001)the Natural Science Foundation of Ningbo,China(2016A610105)
文摘This review focuses on the recent research progress in the multi-component assembly of luminescent rare earth hybrid materials, which is based on the luminescent rare earth compounds and two or more other building units, including the other photoactive species. It covers the multi-component luminescent rare earth hybrids which was assembled with different(a) organic-inorganic polymeric units,(b)nanoporous units,(c) nanoparticle composites or(d) other developing special units. Finally, future challenges and opportunities in this field are discussed. Herein it mainly focuses on the work of Yan's group in recent years.
文摘A general scheme for generating a multi-component integrable equation hierarchy is proposed. A simple 3M- dimensional loop algebra ~X is produced. By taking advantage of ~X a new isospectral problem is established and then by making use of the Tu scheme the multi-component Dirac equation hierarchy is obtained. Finally, an expanding loop algebra ~FM of the loop algebra ~X is presented. Based on the ~FM, the multi-component integrable coupling system of the multi-component Dirac equation hierarchy is investigated. The method in this paper can be applied to other nonlinear evolution equation hierarchies.
基金The research was supported by the Notion's Fifteenth Scientific and Technological Breakthrough Project: Research of Vector and Mountain Seismic Exploration (No.2001BA605A-12).
文摘Seismic AVO analysis now is one of the major criteria for recognizing potential hydrocarbon reservoirs. Volume scattering information that carries information of stratigraphic structure, lithology, and pore fluid is more useful for seismic exploration. However, traditional AVO analysis is based on the Zoeppritz equation, which only contains single-interface information. Quantitative interpretation of the thin bed thickness is essential to thin bed structure interpretation, reservoir description, and lateral reservoir prediction. The reflectance spectrum equation based on the elastic wave propagation matrix in the frequency domain derived in this paper shows that both interfaces and intervals have an effect on amplitude. The equation includes information about both single interfaces and volume scattering. Since the reflectance spectrum equation is a continuous function of thin bed thickness and frequency, it is convenient to analyze the effects of a single frequency and bed thickness on the reflectance spectrum. Bed thickness is analyzable until the bed thickness is vanishingly small. These characteristics can＇t be achieved by Fourier transform. The propagation of seismic waves is complex and various wave modes exist simultaneously. The reflectance spectrum includes various propagating wave modes and multiples and is better for simulating multi-component thin bed AVO responses than the ray tracing method.
基金supported by the National Natural Science Foundation of China Research(Nos.41574122 and 41374124)National Science and Technology major Project(No.2016ZX05006002-004)。
文摘The conventional digital core models are usually small in size and have difficulty in representing the complex structures of heterogeneous rocks;Therefore,the parameters of simulated rock physics are difficult to be referenced.In this study,we propose a feasible simulation method for obtaining multi-scale and multi-component digital cores based on three types of sandstone samples.In the proposed method,the plug and subplug samples are scanned via micro-computed tomography at different resolutions.Furthermore,the images are precisely registered using the proposed hybrid image registration method.In case of high-resolution images,the traditional segmentation method is used to segment the cores into pores and minerals.Subsequently,we established the relations between the gray values and the porosity/mineral content in case of the low-resolution images based on the registered domains and the relation curves were applied to the segmentation of the low-resolution images.The core images constitute the multi-scale and multi-component digital core models after segmentation.Further,the elastic properties of the three samples were simulated at both fine and coarse scales based on the multi-scale and multi-component digital core models,and four component models were considered.The results show that the multi-scale and multi-component digital core models can overcome the representative limits of the conventional digital core models and accurately characterize pores and minerals at different scales.The numerical results of the elastic modulus are more representative at large scales,and considerably reliable results can be obtained by appropriately considering the minerals.
基金supports from the National Natural Science Foundation of China (Grant No. 50931004)the National Basic Research Program of China (Grant Nos. 2011CB610406 and 2010CB631202)the National High Technology Research and Development Program (Grant No. 2007AA03Z552)
文摘The influence of melt superheating treatment on the solid/liquid （S/L） interface morphology of directionally solidified Ni-based superalloy DZ125 is investigated to elucidate the relationship between melt characteristic and S/L interface stability. The results indicate that the interface morphology is not only related to the withdrawal velocity （R） but also to the melt superheating temperature （Ts） when the thermal gradient of solidification interface remains constant for different Ts with appropriate superheating treatment regulation. The interface morphology changes from cell to plane at R of 1.1 μm/s when Ts increases from 1500°C to 1650°C, and maintains plane with further elevated Ts of 1750°C. However, the interface morphology changes from coarse dendrite to cell and then to cellular dendrite at R of 2.25 μm/s when Ts increases from 1500°C to 1650°C and then to 1750°C. It is proved that the solidification onset temperature and the solidification interval undergo the nonlinear variation when Ts increases from 1500°C to 1680°C, and the turning point is 1650°C at which the solidification onset temperature and the solidification interval are all minimum. This indicates that the melt superheating treatment enhances the solidification interface stability and has important effect on the solidification characteristics.
基金Project(71671035)supported by the National Natural Science Foundation of ChinaProjects(ZK15-03-01,ZK16-03-07)supported by Open Fund of Jiangsu Wind Power Engineering Technology Center of China
文摘Aiming at wind turbines,the opportunistic maintenance optimization is carried out for multi-component system,where minimal repair,imperfect repair,replacement as well as their effects on component’s effective age are considered.At each inspection point,appropriate maintenance mode is selected according to the component’s effective age and its maintenance threshold.To utilize the maintenance opportunities for the components among the wind turbines,opportunistic maintenance approach is adopted.Meanwhile,the influence of seasonal factor on the component’s failure rate and improvement factor’s decrease with the increase of repair’s times are also taken into account.The maintenance threshold is set as the decision variable,and an opportunistic maintenance optimization model is proposed to minimize wind turbine’s life-cycle maintenance cost.Moreover,genetic algorithm is adopted to solve the model,and the effectiveness is verified with a case study.The results show that based on the component’s inherent reliability and maintainability,the proposed model can provide optimal maintenance plans accordingly.Furthermore,the higher the component’s reliability and maintainability are,the less the times of repair and replacement will be.
基金Project(51005238)supported by the National Natural Science Foundation of China
文摘To improve the mainlainability design efficiency and quality, a layout optimization method for maintainability of multi-component systems was proposed. The impact of the component layout design on system maintainability was analyzed, and the layout problem for maintainability was presented. It was formulated as an optimization problem, where maintainability, layout space and distance requirement were formulated as objective functions. A multi-objective particle swarm optimization algorithm, in which the constrained-domination relationship and the update strategy of the global best were simply modified, was then used to obtain Pareto optimal solutions for the maintainability layout design problem. Finally, application in oxygen generation system of a spacecraft was studied in detail to illustrate the effectiveness and usefulness of the proposed method. The results show that the concurrent maintainability design can be carried out during the layout design process by solving the layout optimization problem for maintainability.
文摘Elastic waves are affected by viscoelasticity during the propagation through the Earth,resulting in energy attenuation and phase distortion,in turn resulting in low seismic imaging accuracy.Therefore,viscoelasticity should be considered in seismic migration imaging.We propose a Q compensated multicomponent elastic Gaussian beam migration(Q-EGBM)method to(1)separate the elastic-wave data into longitudinal(P)and transverse(S)waves to perform PP-wave and PS-wave imaging;(2)recover the amplitude loss caused by attenuation;(3)correct phase distortions caused by dispersion;(4)improve the resolution of migration imaging.In this paper,to accomplish(2),(3),and(4),we derive complex-valued traveltimes in viscoelastic media.The results of numerical experiments using a simple five-layer model and a sophisticated BP gas model show that the method presented here has significant advantages in recovering energy decay and correcting phase distortion,as well as significantly improving imaging resolution.
基金National Key R&D Program of China(Grant Nos.2017YFC1702400,2018YFC1707300 and 2018YFC1707904)
文摘In the present study, a method for the quantitative analysis of multi-components by single marker(QAMS) has been developed and validated for the simultaneous determination of echinacoside(ECH), tubuloside A, acteoside, isoacteoside, and2’-acetylacteoside in Cistanches Herba. ECH was used as the internal standard(IS) to obtain the relative correction factors(RCFs) of the other four phenylethanoid glycosides(PhGs);meanwhile, various influencing factors on RCFs were investigated under different conditions. The content of each component was calculated with RCF. The results were compared with those obtained by the external standard method(ESM) to verify the feasibility and accuracy of the established QAMS method. No significant difference was found in the quantitative results of 10 batches of Cistanches Herba between QAMS and ESM. The proposed QAMS method for simultaneous determination of PhGs in Cistanches Herba is accurate and feasible, providing an efficient and economical approach for the quality control of Cistanches Herba.
基金the National Key Research and Development Program of China(No.2022YFB3709000)the National Natural Science Foundation of China(Nos.52122408,52071023,52101019,and 51901013)the Fundamental Research Funds for the Central Universities(University of Science and Technology Beijing,Nos.06500135 and FRF-TP-2021-04C1).
文摘Multi-component alloys have demonstrated excellent performance in various applications,but the vast range of possible compositions and microstructures makes it challenging to identify optimized alloys for specific purposes.To overcome this challenge,large-scale atomic simulation techniques have been widely used for the design and optimization of multi-component alloys.The capability and reliability of large-scale atomic simulations essentially rely on the quality of interatomic potentials that describe the interactions between atoms.This work provides a comprehensive summary of the latest advances in atomic simulation techniques for multi-component alloys.The focus is on interatomic potentials,including both conventional empirical potentials and newly developed machine learning potentials(MLPs).The fitting processes for different types of interatomic potentials applied to multi-component alloys are also discussed.Finally,the challenges and future perspectives in developing MLPs are thoroughly addressed.Overall,this review provides a valuable resource for researchers interested in developing optimized multicomponent alloys using atomic simulation techniques.
基金the National Natural Science Foundation of China (Nos. 51774283, 51174203)the Major International (Regional) Joint Research Project of NSFC (No. 51620105001) for the financial supports
文摘The segregation modes and characteristics of 1-6 mm multi-component lignite were studied in a microporous, vibrated, gas-fluidized bed of Φ110 mm ×400 mm. The effects of particle density and size, vibration frequency and amplitude, and gas velocity on these characteristics were considered. The average size, average density, size deviation coefficient, and density deviation coefficient were used to identify lignite size and density. The separation efficiency was adopted to evaluate the segregation performance,and the segregation mechanisms were explored. The results show that ε(size,max) of heterogeneous multisize-component lignite with K_(size) = 65% reaches 80% at f= 20 Hz, A = 5 mm, and N =(1,3). ε_(density,max) Of heterogeneous multi-density-component lignite with K_(density)= 25% reaches 50% at f = 15 Hz, A = 5 mm,and N =(1,1.5). The density segregations of 1-3 and 3-6 mm multi-component mixtures are remarkable,ε_(density,max)= 42% and 31% at f= 14 and 16 Hz, and A = 3 and 5 mm, respectively. The size segregation of 1-6 mm multi-component mixture is prominent and ε_(size,max)= 55% at f= 15 Hz, A = 5 mm. The mediumsized mixture with a narrow size distribution at low frequency is favorable for density segregation,and a mixture with a wider size distribution at high frequency is most favorable for size segregation.Precise control of gas flow and vibration as well as optimal design of the fluidized bed can improve the performance of segregation in the vibrated gas-fluidized bed.
基金supported by the Postdoctoral Science Foundation of China(20080431380)
文摘Although opportunistic maintenance strategies are widely used for multi-component systems, all opportunistic mainte- nance strategies only consider economic dependence and do not take structural dependence into account. An opportunistic main- tenance strategy is presented for a multi-component system that considers both structural dependence and economic dependence. The cost relation and time relation among components based on structural dependence are developed. The maintenance strategy for each component of a multi-component system involves one of five maintenance actions, namely, no-maintenance, a minimal maintenance action, an imperfect maintenance action, a perfect maintenance action, and a replacement action. The maintenance action is determined by the virtual age of the component, the life expectancy of the component, and the age threshold values. Monte Carlo simulation is designed to obtain the optimal oppor- tunistic maintenance strategy of the system over its lifetime. The simulation result reveals that the minimum maintenance cost with a strategy that considers structural dependence is less than that with a strategy that does not consider structural dependence. The availability with a strategy that considers structural dependence is greater than that with a strategy that does not consider structural dependence under the same conditions.
基金National Natural Science Foundations of China(No.71501103)Natural Science Foundation of Inner Mongolia,China(No.2015BS0705)the Program of Higher-Level Talents of Inner Mongolia University,China(No.20700-5145131)
文摘Complex repairable system is composed of thousands of components.Some maintenance management and decision problems in maintenance management and decision need to classify a set of components into several classes based on data mining.Furthermore,with the complexity of industrial equipment increasing,the managers should pay more attention to the key components and carry out the lean management is very important.Therefore,the idea"customer segmentation"of"precise marketing"can be used in the maintenance management of the multi-component system.Following the idea of segmentation,the components of multicomponent systems should be subdivied into groups based on specific attributes relevant to maintenance,such as maintenance cost,mean time between failures,and failure frequency.For the target specific groups of parts,the optimal maintenance policy,health assessment and maintenance scheduling can be determined.The proposed analysis framework will be given out.In order to illustrate the effectiveness of this method,a numerical example is given out.
基金Projects (51275138,51605016) supported by the National Natural Science Foundation of ChinaProject (12531109) supported by the Science Foundation of Heilongjiang Provincial Department of Education,ChinaProject supported by Research Start-up Funding of Fudan University,China
文摘For unacceptable computational efficiency and accuracy on the probabilistic analysis of multi-component system with multi-failure modes,this paper proposed multi-extremum response surface method(MERSM).MERSM model was established based on quadratic polynomial function by taking extremum response surface model as the sub-model of multi-response surface method.The dynamic probabilistic analysis of an aeroengine turbine blisk with two components,and their reliability of deformation and stress failures was obtained,based on thermal-structural coupling technique,by considering the nonlinearity of material parameters and the transients of gas flow,gas temperature and rotational speed.The results show that the comprehensive reliability of structure is 0.9904 when the allowable deformations and stresses of blade and disk are 4.78×10–3 m and 1.41×109 Pa,and 1.64×10–3 m and 1.04×109 Pa,respectively.Besides,gas temperature and rotating speed severely influence the comprehensive reliability of system.Through the comparison of methods,it is shown that the MERSM holds higher computational precision and speed in the probabilistic analysis of turbine blisk,and MERSM computational precision satisfies the requirement of engineering design.The efforts of this study address the difficulties on transients and multiple models coupling for the dynamic probabilistic analysis of multi-component system with multi-failure modes.
基金supported by the Open Project of State Key Laboratory of Powder Metallurgy of Central South University (Grant No. 2008112042)the National Natural Science Foundation of China (Grant Nos. 51071062 and 50801019)Project 973 (Grant No. 2011CB610406)
文摘On the basis of a multi-length scale modeling, a mixture-averaged multi-component/multiphase micro- segregation model was proposed without pre-set function for the micro-scale solute profile. The model explains the effect of morphologies of solidifying phases and solid back diffusion （SBD） on segregation, and covers the two limiting solidification cases of Scheil and Lever-rule models. A commercial Thermo-Calc software package/database was linked to the algorithms via its TQ6-interface for instantaneous determination of the related thermodynamic data of the multi-component alloys. The influences of cooling rate and other parameters on the solidification path and micro-segregation behavior were numerically investigated by sample calculation of the ternary AI-Cu-Mg alloys. A parallel experimental investigation on AI-Cu-Si alloys solidified under different cooling conditions was conducted to validate the theoretical model. Reasonable agreements were gained between the predicted solidification paths and the measured results.
文摘A three component one-pot protocol was investigated for the synthesis of methylene bis isoxazolo[4,5-b]-pyridine-N-oxides from commercially available materials.
