The reduction of carbon emissions in the steel industry is a significant challenge,and utilizing CO_(2) from carbon intensive steel industry off-gases for methanol production is a promising strategy for decarbonizatio...The reduction of carbon emissions in the steel industry is a significant challenge,and utilizing CO_(2) from carbon intensive steel industry off-gases for methanol production is a promising strategy for decarbonization.However,steelwork off-gases typically contain various impurities,including H_(2)S,which can deactivate commercial methanol synthesis catalysts,Cu/ZnO/Al_(2)O_(3)(CZA).Reverse water-gas shift(RWGS)reaction is the predominant side reaction in CO_(2) hydrogenation to methanol which can occur at ambient pressure,enabling the decouple of RWGS from methanol production at high pressure.Then,a series of activated CZA catalysts has been in-situ pretreated in 400 ppm H_(2)S/Ar at 250℃and tested for both RWGS reaction at ambient pressure and CO_(2) hydrogenation to methanol at high pressure.An innovative decoupling strategy was employed to isolate the RWGS reaction from the methanol synthesis process,enabling the investigation of the evolution of active site structures and the poisoning mechanism through elemental analysis,X-ray Diffraction,X-ray Photoelectron Spectroscopy,Fourier Transform Infrared Spectroscopy,Temperature Programmed Reduction and CO_(2) Temperature Programmed Desorption.The results indicate that there are different dynamic migration behaviors of ZnO_(x) in the two reaction systems,leading to different poisoning mechanisms.These interesting findings are beneficial to develop sulfur resistant and durable highly efficient catalysts for CO_(2) hydrogenation to methanol,promoting the carbon emission reduction in steel industry.展开更多
以硝酸铝和尿素为原料,通过水热法成功合成富含五配位Al^(3+)的γ-Al_(2)O_(3)载体,采用XRD、SEM、STEM-HAADF、27Al MAS NMR、N_(2)吸附-脱附等手段表征了载体的物理化学性质,并对采用该载体制备的Pd/Al_(2)O_(3)催化剂进行了蒽醌加氢...以硝酸铝和尿素为原料,通过水热法成功合成富含五配位Al^(3+)的γ-Al_(2)O_(3)载体,采用XRD、SEM、STEM-HAADF、27Al MAS NMR、N_(2)吸附-脱附等手段表征了载体的物理化学性质,并对采用该载体制备的Pd/Al_(2)O_(3)催化剂进行了蒽醌加氢制H_(2)O_(2)的初步性能评价。表征结果显示,合成的载体中的五配位Al^(3+)相对含量可达40.88%(w),微观粒子呈棒状,棒的长度1~4μm,直径0.1~0.3μm,BET比表面积可达494 m^(2)/g;所制备的Pd/Al_(2)O_(3)催化剂中Pd纳米粒子分散良好,平均粒径为3.51 nm,且分布较窄。评价结果表明,该催化剂相对于参比剂具有较高的加氢活性。展开更多
The ineluctable introduction of lithium salt to polymer solid-state electrolytes incurs a compromise between strength,ionic conductivity,and thickness.Here,we propose Al_(2)O_(3)-coated polyimide(AO/PI)porous film as ...The ineluctable introduction of lithium salt to polymer solid-state electrolytes incurs a compromise between strength,ionic conductivity,and thickness.Here,we propose Al_(2)O_(3)-coated polyimide(AO/PI)porous film as a high-strength substrate to support fast-ion-conducting polymer-in-salt(PIS)solid-state electrolytes,aiming to suppress lithium dendrite growth and improve full-cell performance.The Al_(2)O_(3)coating layer not only refines the wettability of polyimide porous film to PIS,but also performs as a high modulus protective layer to suppress the growth of lithium dendrites.The resulting PI/AO@PIS exhibits a small thickness of only 35μm with an outstanding tensile strength of 11.3 MPa and Young's modulus of 537.6 MPa.In addition,the PI/AO@PIS delivers a high ionic conductivity of 0.1 m S/cm at 25°C.As a result,the PI/AO@PIS enables symmetric Li cells to achieve exceptional cyclability for over 1000 h at 0.1 m A/cm2without noticeable lithium dendrite formation.Moreover,the PI/AO@PIS-based LiFePO4||Li full cells demonstrate outstanding rate performance(125.7 m Ah/g at 5 C)and impressive cycling stability(96.1%capacity retention at 1 C after 200 cycles).This work highlights the efficacy of enhancing the mechanical properties of polymer matrices and extending cell performance through the incorporation of a dense inorganic interface layer.展开更多
We first present preparation of MnOx–CeO_2–Al_2O_3 catalysts with varying Mn contents through a self-propagating high-temperature synthesis(SHS) method, and studied the application of these catalysts to the selectiv...We first present preparation of MnOx–CeO_2–Al_2O_3 catalysts with varying Mn contents through a self-propagating high-temperature synthesis(SHS) method, and studied the application of these catalysts to the selective catalytic reduction of NOxwith NH3(NH_3-SCR).Using the catalyst with 18 wt.% Mn(18 MnCe1Al2), 100% NO conversion was achieved at 200°C and a gas hourly space velocity of 15384 hr-1, and the high-efficiency SCR temperature window, where NO conversion is greater than 90%, was widened to a temperature range of 150–300°C. 18 MnCe1Al2 showed great resistance to SO_2(100 ppm)and H_2O(5%) at 200°C. The catalysts were characterized using X-ray diffraction, X-ray photoelectron spectroscopy, Brunauer–Emmett–Teller(BET) analysis, scanning electron microscopy, Fourier transform infrared spectroscopy, and H_2 temperature programmed reduction. The characterization results showed that the surface atomic concentration of Mn increased with increasing Mn content, which led to synergism between Mn and Ce and improved the activity in the SCR reaction. 18 MnCe1Al2 has an extensive pore structure,with a BET surface area of approximately 135.4 m^2/g, a pore volume of approximately 0.16 cm^3/g, and an average pore diameter of approximately 4.6 nm. The SCR reaction on 18 MnCe1Al2 mainly followed the Eley-Rideal mechanism. The performances of the MnOx–CeO_2–Al_2O_3 catalysts were good, and because of the simplicity of the preparation process,the SHS method is applicable to their industrial-scale manufacture.展开更多
Processes based on non-thermal plasma（NTP） for indoor air treatment inevitably lead to the formation of toxic by-products such as ozone（O3） and nitrogen oxides（NOx）. Adding a step of heterogeneous catalysis in s...Processes based on non-thermal plasma（NTP） for indoor air treatment inevitably lead to the formation of toxic by-products such as ozone（O3） and nitrogen oxides（NOx）. Adding a step of heterogeneous catalysis in series with NTP could allow for the decomposition of the by-products. Therefore, different catalysts were developed based on transition metal oxides, such as NiOx, CoOxand MnOxwith different weight percentage 1, 5 and 10 wt.%,deposited on a γ-Al2O3 support. The O3 removal efficiency（ORE） and the NOxremoval efficiency（NRE） were very encouraging in dry air： about 65% and 80%, respectively, by using2 g 5 wt.% MnOx/Al2O3 catalyst under the experimental conditions. However, strongly negative effects of relative humidity（RH） on the catalytic decomposition performance were observed. To overcome this limitation, the catalyst surface was modified to make it hydrophobic using a cost-effective chemical grafting method. This treatment consisted in impregnating the 5 wt.% MnOx/Al2O3 catalyst with different trichloro（alkyl）silanes（TCAS）.The effects of different linker lengths and amounts of TCAS for the hydrophobicity and the decomposition performance of surface-modified catalysts under humid conditions were investigated. Our results show that the surface-modified catalyst with the shortest linker and 0.25 mmol/gcatof modifying agent represents the best catalytic decomposition performance for O3. Its ORE is 41% at 60% RH, which is twice that of the non-modified catalyst.展开更多
A La-modified Al2O3 catalyst was prepared with deposition-precipitation method. The effect of calcination temperature on the reactivity for vapor phase hydrofluorination of acetylene to vinyl fluoride. The catalysts c...A La-modified Al2O3 catalyst was prepared with deposition-precipitation method. The effect of calcination temperature on the reactivity for vapor phase hydrofluorination of acetylene to vinyl fluoride. The catalysts calcined at different temperatures were characterized using NH3-TPD, pyridine-FTIR, X-ray diffraction, and Raman techniques. It was found that the calcination process could not only change the structure of these catalysts but also modify the amount of surface acidity on the catalysts. The catalyst calcined at 400 ℃ exhibited the highest conversion of acetylene （94.6%） and highest selectivity to vinyl fluoride （83.4%） and lower coke deposition selectivity （0.72%）. The highest activity was related to the largest amount of surface acidity on the catalyst, and the coke deposition was also related to the total amount of surface acidic sites.展开更多
In this paper, KMnO4 was used to pre-treat Co3 Fe-layered double hydroxides(LDH) precursor to prepare MnO2 decorated Co3Fe1Ox catalyst. The toluene oxidation performance of the catalyst was investigated systematically...In this paper, KMnO4 was used to pre-treat Co3 Fe-layered double hydroxides(LDH) precursor to prepare MnO2 decorated Co3Fe1Ox catalyst. The toluene oxidation performance of the catalyst was investigated systematically. The optimized 0.1 Mn CF-LDO catalyst exhibited the best catalytic performance, and the temperatures of 50% and 90% toluene conversion( T50 and T90) were 218 and 243 ℃, respectively. The apparent activation energy( Ea) was 31.6 k J/mol. The characterization results showed that the pre-redox reaction by KMnO4 could increase the specific surface area, Co^3+ species amount and oxygen defect concentration of the catalyst, which are the main reason of the improved toluene catalytic activity. Besides, this method was also applied to enhance toluene oxidation of iron mesh based monolithic catalyst. The 0.1 Mn CF-LDO/Iron mesh(IM) catalyst showed a 90% toluene conversion at around 316 ℃ which was much lower than that of without MnO2 addition(359 ℃). In addition, the water resistant of all the catalysts was studied as well, all the samples showed relatively good water resistance. The toluene conversion still remained to be over > 80% even in the presence of 10 vol.% water vapor.展开更多
基金supported by the National Natural Science Foundation of China(Nos.22276060 and 21976059)Guangdong Basic and Applied Basic Research Foundation(No.2024A1515012636)China Scholarship Council Scholarship(No.201906155006)。
文摘The reduction of carbon emissions in the steel industry is a significant challenge,and utilizing CO_(2) from carbon intensive steel industry off-gases for methanol production is a promising strategy for decarbonization.However,steelwork off-gases typically contain various impurities,including H_(2)S,which can deactivate commercial methanol synthesis catalysts,Cu/ZnO/Al_(2)O_(3)(CZA).Reverse water-gas shift(RWGS)reaction is the predominant side reaction in CO_(2) hydrogenation to methanol which can occur at ambient pressure,enabling the decouple of RWGS from methanol production at high pressure.Then,a series of activated CZA catalysts has been in-situ pretreated in 400 ppm H_(2)S/Ar at 250℃and tested for both RWGS reaction at ambient pressure and CO_(2) hydrogenation to methanol at high pressure.An innovative decoupling strategy was employed to isolate the RWGS reaction from the methanol synthesis process,enabling the investigation of the evolution of active site structures and the poisoning mechanism through elemental analysis,X-ray Diffraction,X-ray Photoelectron Spectroscopy,Fourier Transform Infrared Spectroscopy,Temperature Programmed Reduction and CO_(2) Temperature Programmed Desorption.The results indicate that there are different dynamic migration behaviors of ZnO_(x) in the two reaction systems,leading to different poisoning mechanisms.These interesting findings are beneficial to develop sulfur resistant and durable highly efficient catalysts for CO_(2) hydrogenation to methanol,promoting the carbon emission reduction in steel industry.
文摘以硝酸铝和尿素为原料,通过水热法成功合成富含五配位Al^(3+)的γ-Al_(2)O_(3)载体,采用XRD、SEM、STEM-HAADF、27Al MAS NMR、N_(2)吸附-脱附等手段表征了载体的物理化学性质,并对采用该载体制备的Pd/Al_(2)O_(3)催化剂进行了蒽醌加氢制H_(2)O_(2)的初步性能评价。表征结果显示,合成的载体中的五配位Al^(3+)相对含量可达40.88%(w),微观粒子呈棒状,棒的长度1~4μm,直径0.1~0.3μm,BET比表面积可达494 m^(2)/g;所制备的Pd/Al_(2)O_(3)催化剂中Pd纳米粒子分散良好,平均粒径为3.51 nm,且分布较窄。评价结果表明,该催化剂相对于参比剂具有较高的加氢活性。
基金the financial support from the 261Project of MIIT and Natural Science Foundation of Jiangsu Province(No.BK20240179)。
文摘The ineluctable introduction of lithium salt to polymer solid-state electrolytes incurs a compromise between strength,ionic conductivity,and thickness.Here,we propose Al_(2)O_(3)-coated polyimide(AO/PI)porous film as a high-strength substrate to support fast-ion-conducting polymer-in-salt(PIS)solid-state electrolytes,aiming to suppress lithium dendrite growth and improve full-cell performance.The Al_(2)O_(3)coating layer not only refines the wettability of polyimide porous film to PIS,but also performs as a high modulus protective layer to suppress the growth of lithium dendrites.The resulting PI/AO@PIS exhibits a small thickness of only 35μm with an outstanding tensile strength of 11.3 MPa and Young's modulus of 537.6 MPa.In addition,the PI/AO@PIS delivers a high ionic conductivity of 0.1 m S/cm at 25°C.As a result,the PI/AO@PIS enables symmetric Li cells to achieve exceptional cyclability for over 1000 h at 0.1 m A/cm2without noticeable lithium dendrite formation.Moreover,the PI/AO@PIS-based LiFePO4||Li full cells demonstrate outstanding rate performance(125.7 m Ah/g at 5 C)and impressive cycling stability(96.1%capacity retention at 1 C after 200 cycles).This work highlights the efficacy of enhancing the mechanical properties of polymer matrices and extending cell performance through the incorporation of a dense inorganic interface layer.
基金supported by the National High Technology Research and Development Program of China (863 program) (No.2015AA03A401)the Program for Changjiang Scholars and Innovative Research Team in University (No.IRT_15R46)the program of Science and Technology Innovation Team in Bingtuan (No.2015BD003)
文摘We first present preparation of MnOx–CeO_2–Al_2O_3 catalysts with varying Mn contents through a self-propagating high-temperature synthesis(SHS) method, and studied the application of these catalysts to the selective catalytic reduction of NOxwith NH3(NH_3-SCR).Using the catalyst with 18 wt.% Mn(18 MnCe1Al2), 100% NO conversion was achieved at 200°C and a gas hourly space velocity of 15384 hr-1, and the high-efficiency SCR temperature window, where NO conversion is greater than 90%, was widened to a temperature range of 150–300°C. 18 MnCe1Al2 showed great resistance to SO_2(100 ppm)and H_2O(5%) at 200°C. The catalysts were characterized using X-ray diffraction, X-ray photoelectron spectroscopy, Brunauer–Emmett–Teller(BET) analysis, scanning electron microscopy, Fourier transform infrared spectroscopy, and H_2 temperature programmed reduction. The characterization results showed that the surface atomic concentration of Mn increased with increasing Mn content, which led to synergism between Mn and Ce and improved the activity in the SCR reaction. 18 MnCe1Al2 has an extensive pore structure,with a BET surface area of approximately 135.4 m^2/g, a pore volume of approximately 0.16 cm^3/g, and an average pore diameter of approximately 4.6 nm. The SCR reaction on 18 MnCe1Al2 mainly followed the Eley-Rideal mechanism. The performances of the MnOx–CeO_2–Al_2O_3 catalysts were good, and because of the simplicity of the preparation process,the SHS method is applicable to their industrial-scale manufacture.
基金financially supported by French Ministry of Higher Education and Research (No. 2015/386)
文摘Processes based on non-thermal plasma（NTP） for indoor air treatment inevitably lead to the formation of toxic by-products such as ozone（O3） and nitrogen oxides（NOx）. Adding a step of heterogeneous catalysis in series with NTP could allow for the decomposition of the by-products. Therefore, different catalysts were developed based on transition metal oxides, such as NiOx, CoOxand MnOxwith different weight percentage 1, 5 and 10 wt.%,deposited on a γ-Al2O3 support. The O3 removal efficiency（ORE） and the NOxremoval efficiency（NRE） were very encouraging in dry air： about 65% and 80%, respectively, by using2 g 5 wt.% MnOx/Al2O3 catalyst under the experimental conditions. However, strongly negative effects of relative humidity（RH） on the catalytic decomposition performance were observed. To overcome this limitation, the catalyst surface was modified to make it hydrophobic using a cost-effective chemical grafting method. This treatment consisted in impregnating the 5 wt.% MnOx/Al2O3 catalyst with different trichloro（alkyl）silanes（TCAS）.The effects of different linker lengths and amounts of TCAS for the hydrophobicity and the decomposition performance of surface-modified catalysts under humid conditions were investigated. Our results show that the surface-modified catalyst with the shortest linker and 0.25 mmol/gcatof modifying agent represents the best catalytic decomposition performance for O3. Its ORE is 41% at 60% RH, which is twice that of the non-modified catalyst.
基金ACKNOWLEDGMENT This work was supported by the National Natural Science Foundation of China （No.20873125）,
文摘A La-modified Al2O3 catalyst was prepared with deposition-precipitation method. The effect of calcination temperature on the reactivity for vapor phase hydrofluorination of acetylene to vinyl fluoride. The catalysts calcined at different temperatures were characterized using NH3-TPD, pyridine-FTIR, X-ray diffraction, and Raman techniques. It was found that the calcination process could not only change the structure of these catalysts but also modify the amount of surface acidity on the catalysts. The catalyst calcined at 400 ℃ exhibited the highest conversion of acetylene （94.6%） and highest selectivity to vinyl fluoride （83.4%） and lower coke deposition selectivity （0.72%）. The highest activity was related to the largest amount of surface acidity on the catalyst, and the coke deposition was also related to the total amount of surface acidic sites.
基金supported by the Fundamental Research Funds for the Central Universities (No. 2019JQ03015)the National Natural Science Foundation of China (No. U1810209)+1 种基金the International Science and Technology Cooperation Project of Bingtuan (No. 2018BC002)the Beijing Municipal Educa-tion Commission for their financial support through Innova-tive Transdisciplinary Program “Ecological Restoration Engi-neering”。
文摘In this paper, KMnO4 was used to pre-treat Co3 Fe-layered double hydroxides(LDH) precursor to prepare MnO2 decorated Co3Fe1Ox catalyst. The toluene oxidation performance of the catalyst was investigated systematically. The optimized 0.1 Mn CF-LDO catalyst exhibited the best catalytic performance, and the temperatures of 50% and 90% toluene conversion( T50 and T90) were 218 and 243 ℃, respectively. The apparent activation energy( Ea) was 31.6 k J/mol. The characterization results showed that the pre-redox reaction by KMnO4 could increase the specific surface area, Co^3+ species amount and oxygen defect concentration of the catalyst, which are the main reason of the improved toluene catalytic activity. Besides, this method was also applied to enhance toluene oxidation of iron mesh based monolithic catalyst. The 0.1 Mn CF-LDO/Iron mesh(IM) catalyst showed a 90% toluene conversion at around 316 ℃ which was much lower than that of without MnO2 addition(359 ℃). In addition, the water resistant of all the catalysts was studied as well, all the samples showed relatively good water resistance. The toluene conversion still remained to be over > 80% even in the presence of 10 vol.% water vapor.
