The single-phase heat transfer characteristics in a PWR fuel assembly are important. Many investigations attempt to obtain the heat transfer characteristics by studying the flow features in a 5 x 5 rod bundle with a s...The single-phase heat transfer characteristics in a PWR fuel assembly are important. Many investigations attempt to obtain the heat transfer characteristics by studying the flow features in a 5 x 5 rod bundle with a spacer grid. The field synergy principle is used to discuss the mechanism of heat transfer enhancement using mixing vanes according to computational fluid dynamics results, including a spacer grid without mixing vanes, one with a split mixing vane, and one with a separate mixing vane. The results show that the field synergy principle is feasible to explain the mechanism of heat transfer enhancement in a fuel assembly. The enhancement in subchannels is more effective than on the rod＇s surface. If the pressure loss is ignored, the performance of the split mixing vane is superior to the separate mixing vane based on the enhanced heat transfer. Increasing the blending angle of the split mixing vane improves heat transfer enhancement, the maximum of which is 7.1%. Increasing the blending angle of the separate mixing vane did not significantly enhance heat transfer in the rod btmdle, and even prevented heat transfer at a blending angle of 50%. This fmding testifies to the feasibility of predicting heat transfer in a rod bundle with a spacer grid by field synergy, and upon comparison with analyzed flow features only, the field synergy method may provide more accurate guidance for optimizing the use of mixing vanes.展开更多
In nuclear reactor fuel assemblies, spacer grids are installed among the rod bundles to support the fuel rods and affect the flow field between rods. Mixing vanes, as a swirling device, are set on the upper apex of th...In nuclear reactor fuel assemblies, spacer grids are installed among the rod bundles to support the fuel rods and affect the flow field between rods. Mixing vanes, as a swirling device, are set on the upper apex of the spacer grid. Vortexes produced by mixing vanes move along the axial direction in subchannels and enhance the forced convection heat transfer between the rods and cooling-fluid medium. In this paper, a numerical simulation method was used to investigate vortex motion produced by typical AFA-3G spacer grids in a 5×5-rod bundle by Star-CCM+ software. The shear-stress transport k-ω model was used to simulate turbulence phenomena. A dimensionless parameter, Se, based on the absolute vorticity flux, was reported to specify the intensity of secondary flow. Its physical meaning is the ratio of inertial force to viscous force induced by secondary flow. The results are helpful to take advantage of spacer grids in a much more effective way in pressurized water reactors.展开更多
基金Supported by National Natural Science Foundation of China(Grant No.51376022)
文摘The single-phase heat transfer characteristics in a PWR fuel assembly are important. Many investigations attempt to obtain the heat transfer characteristics by studying the flow features in a 5 x 5 rod bundle with a spacer grid. The field synergy principle is used to discuss the mechanism of heat transfer enhancement using mixing vanes according to computational fluid dynamics results, including a spacer grid without mixing vanes, one with a split mixing vane, and one with a separate mixing vane. The results show that the field synergy principle is feasible to explain the mechanism of heat transfer enhancement in a fuel assembly. The enhancement in subchannels is more effective than on the rod＇s surface. If the pressure loss is ignored, the performance of the split mixing vane is superior to the separate mixing vane based on the enhanced heat transfer. Increasing the blending angle of the split mixing vane improves heat transfer enhancement, the maximum of which is 7.1%. Increasing the blending angle of the separate mixing vane did not significantly enhance heat transfer in the rod btmdle, and even prevented heat transfer at a blending angle of 50%. This fmding testifies to the feasibility of predicting heat transfer in a rod bundle with a spacer grid by field synergy, and upon comparison with analyzed flow features only, the field synergy method may provide more accurate guidance for optimizing the use of mixing vanes.
文摘In nuclear reactor fuel assemblies, spacer grids are installed among the rod bundles to support the fuel rods and affect the flow field between rods. Mixing vanes, as a swirling device, are set on the upper apex of the spacer grid. Vortexes produced by mixing vanes move along the axial direction in subchannels and enhance the forced convection heat transfer between the rods and cooling-fluid medium. In this paper, a numerical simulation method was used to investigate vortex motion produced by typical AFA-3G spacer grids in a 5×5-rod bundle by Star-CCM+ software. The shear-stress transport k-ω model was used to simulate turbulence phenomena. A dimensionless parameter, Se, based on the absolute vorticity flux, was reported to specify the intensity of secondary flow. Its physical meaning is the ratio of inertial force to viscous force induced by secondary flow. The results are helpful to take advantage of spacer grids in a much more effective way in pressurized water reactors.
