Iron phosphate based glass-ceramics with deliberately added Ce as an active nuclide simulant were prepared by microwave sintering.The sintering characteristics,including phases and structural evolution,and chemical du...Iron phosphate based glass-ceramics with deliberately added Ce as an active nuclide simulant were prepared by microwave sintering.The sintering characteristics,including phases and structural evolution,and chemical durability were investigated.XRD showed that NaZr_(2)(PO_(4))_(3) and FePO_(4) became the main crystalline phases of glass-ceramics with increasing sintering temperature.SEM revealed the glass-ceramics compactness increased first and then decreased as sintering temperature increased.Raman spectrum showed that,as sintering temperature increased,the network structure of glass-ceramics changed from mainly containing orthophosphate and pyrophosphate to a single orthophosphate.After immersion for 28 days,LR_(Na),LR_(Zr) and LR_(Ce) of the glass-ceramics prepared at 1000℃ were as low as 3.64×10^(-5),0.25×10^(-9) and 5.70×10^(-9)g/m^(2)/d respectively.The results indicate that iron phosphate based glass-ceramics can be prepared by rapid microwave sintering of glass powders and there is a potential of employing such microwave sintering technique in processing of glass-ceramics nuclear waste form.展开更多
WC-8Co cemented carbide samples were processed via microwave irradiation in a 2.45 GHz, high-power multi-mode microwave cavity. The densification of the compacts and the microstructures of the prepared alloys were stu...WC-8Co cemented carbide samples were processed via microwave irradiation in a 2.45 GHz, high-power multi-mode microwave cavity. The densification of the compacts and the microstructures of the prepared alloys were studied. The results demonstrate that the liquid phase is formed around 1300 ℃ and nearly full densification is obtained at 1450 ℃ for 5 min via microwave irradiation. The microstructures of microwave sintered samples have finer and more uniform WC grains than those of vacuum sintered samples. Besides, the WC grain size and distribution are only decided by the sintering temperature. Holding time has negligible effects on them. No matter how holding time is, the mean grain size is 2.7 pan when the sintering temperature is kept at 1450 ℃.展开更多
Cemented tungsten carbide with ultra fine grains was prepared via microwave sintering.η phase（W3Co3C） was formed on the surface of the samples during the preparation process.Extra carbon black was premixed and the ...Cemented tungsten carbide with ultra fine grains was prepared via microwave sintering.η phase（W3Co3C） was formed on the surface of the samples during the preparation process.Extra carbon black was premixed and the influence of carbon content on mechanical properties was studied.The results show that the maximum value of hardness and transverse rupture strength are HRA 93.2 and 3396 MPa respectively when the carbon black content is 0.45%.The microstructure investigated by SEM show that the WC grains growth mainly occurs during the early stage of microwave sintering by the coalescence of grains.展开更多
Al−2CNTs−xAl2O3 nanocomposites were manufactured by a hybrid powder metallurgy and microwave sintering process.The correlation between process-induced microstructural features and the material properties including phy...Al−2CNTs−xAl2O3 nanocomposites were manufactured by a hybrid powder metallurgy and microwave sintering process.The correlation between process-induced microstructural features and the material properties including physical and mechanical properties as well as ultrasonic parameters was measured.It was found that physical properties including densification and physical dimensional changes were closely associated with the morphology and particle size of nanocomposite powders.The maximum density was obtained by extensive particle refinement at milling time longer than 8 h and Al2O3 content of 10 wt.%.Mechanical properties were controlled by Al2O3 content,dispersion of nano reinforcements and grain size.The optimum hardness and strength properties were achieved through incorporation of 10 wt.%Al2O3 and homogenous dispersion of CNTs and Al2O3 nanoparticles(NPs)at 12 h of milling which resulted in the formation of high density of dislocations and extensive grain size refinement.Also both longitudinal and shear velocities and attenuation increase linearly by increasing Al2O3 content and milling time.The variation of ultrasonic velocity and attenuation was attributed to the degree of dispersion of CNTs and Al2O3 and also less inter-particle spacing in the matrix.The larger Al2O3 content and more homogenous dispersion of CNTs and Al2O3 NPs at longer milling time exerted higher velocity and attenuation of ultrasonic wave.展开更多
In order to prepare high-performance Mo with fine and homogeneous microstructure to meet the demand of high-technology applications such as metallurgical,mechanical,national defense,aerospace and electronics applicati...In order to prepare high-performance Mo with fine and homogeneous microstructure to meet the demand of high-technology applications such as metallurgical,mechanical,national defense,aerospace and electronics applications,the microwave sintering process and densification mechanism of Mo nanopowder were studied.In this experiment,Mo nanopowder and micropowder were used for conventional sintering and microwave sintering at different sintering temperatures and sintering time,respectively.The results showed that with the increase in the sintering temperature,the increase rates of the relative density and hardness increased rapidly at first and then slowed down.The relative density rapidly reached 95%,followed by a small change.Mo nanopowder with a relative density of 98.03% and average grain size of 3.6 μm was prepared by microwave sintering at 1873 K for30 min.According to the analysis of the sintering kinetics,its densification is attributed to the combination of volumetric diffusion and grain boundary diffusion mechanisms.The calculated sintering activation energy of Mo nanopowder was 203.65 kJ/mol,which was considerably lower than that in the conventional sintering,suggesting that the microwave sintering was beneficial to the enhancement in the atom diffusion and densification for the powder.The results confirm that the microwave sintering is a promising method to economically prepare molybdenum with high properties.展开更多
Steel-cemented WC was prepared by ball milling, cold compacting and microwave sintering with Fe powder as the matrix, WC as the hard phase and the addition of rare earth Y2O3. The results show that the interface of th...Steel-cemented WC was prepared by ball milling, cold compacting and microwave sintering with Fe powder as the matrix, WC as the hard phase and the addition of rare earth Y2O3. The results show that the interface of the WC particles and Fe matrix exhibits excellent wettability and liquidity when the microwave sintering temperature reaches 1,280℃. The density and mechanical properties of the steel bonded WC carbides could be greatly improved, the hard phases become finer and more uniform dispersed owing to the addition of Y2O3. With the increase of the Y2O3 contents, the grain becomes uniform and fine first, and then gathers and grows up. The relative density, microhardness and bending strength all rise first, reaching the maximum values of 97.29 %, HV1024 and 1,267.60 MPa at 0.5 % Y2O3, respectively, and then decrease. Moreover, the relative density and mechanical properties of the steel-cemented WC with nano-Y2O3 are higher than that with micron-Y2O3, which indicates that the effect of nano-Y2O3 is better than that of the micron-Y2O3.展开更多
To obtain the lightweight,high strength,and high damping capacity porous NiTi alloys,the microwave sintering coupled with the Mg space holder technique was employed to prepare the porous NiTi alloys.The microstructure...To obtain the lightweight,high strength,and high damping capacity porous NiTi alloys,the microwave sintering coupled with the Mg space holder technique was employed to prepare the porous NiTi alloys.The microstructure,mechanical properties,phase transformation behavior,superelasticity,and damping capacity of the porous NiTi alloys were investigated.The results show that the porous NiTi alloys are mainly composed of the B2 NiTi phase with a few B19'NiTi phase as the sintering temperature is lower than or equal to 900℃.With increasing the sintering temperature,the porosities of the porous NiTi alloys gradually decrease and the compressive strength increases first,reaching the maximum value at 900℃,and then decreases.With increasing the Mg content from 1 wt.%to 7 wt.%,the porosities of the porous NiTi alloys increase from 37.8%to 47.1%,while the compressive strength decreases from 2058 to 1146 MPa.Compared with the NH4HCO3 space holder,the phase transformation behavior of the porous NiTi alloys prepared with Mg space holder changes,and all of the compressive strength,superelasticity,shape memory effect and damping capacity are greatly improved.展开更多
Porous Ti-23%Nb(mole fraction)shape memory alloys(SMAs)were prepared successfully by microwave sintering with excellent outer finishing(without space holder).The effects of microwave-sintering on the microstructure,ph...Porous Ti-23%Nb(mole fraction)shape memory alloys(SMAs)were prepared successfully by microwave sintering with excellent outer finishing(without space holder).The effects of microwave-sintering on the microstructure,phase composition,phase-transformation temperature,mechanical properties and shape-memory effect were investigated.The results show that the density and size of porosity vary based on the sintering time and temperature,in which the smallest size and the most uniform pore shape are exhibited with Ti-23%Nb SMA after being sintered at 900°C for 30 min.The microstructure of porous Ti-Nb SMA consists of predominantα',α,andβphases in needle-like and plate-like morphologies,and their volume fractions vary based on the sintering time and temperature.Theβphase represents the largest phase due to the higher content ofβstabilizer element with little intensities ofαandα'phases.The highest ultimate strength and its strain are indicated for the sample sintered at 900°C for 30 min,while the best superelasticity is for the sample sintered at 1200°C for 30 min.The low-elastic modulus enables these alloys to avoid the problem of“stress shielding”.Therefore,microwave heating can be employed to sinter Ti-alloys for biomedical applications and improve the mechanical properties of these alloys.展开更多
Ultra-fine titanium carbonitride （TiCN） matrix materials with a grain size less than 1μm were successfully prepared by vacuum microwave sintering. The milling process for raw TiCN particles and the microstructure a...Ultra-fine titanium carbonitride （TiCN） matrix materials with a grain size less than 1μm were successfully prepared by vacuum microwave sintering. The milling process for raw TiCN particles and the microstructure and properties of cermets produced with a composition of 15wt.%WC-17wt.%（Co＋Ni）-9wt.%Mo2C-59wt.%Ti0.TN0.3 and sintered by vacuum microwave were analyzed by scanning electron microscopy （SEM） and X-ray diffraction （XRD）. The results show that a ball-to-powder mass ratio of 8：1 and a milling time of 50 h provided appropriate conditions for the production of ultra-fine TiCN solid solution powders. The use of vacuum microwave sintering produced cermets with much finer grain and black core structures and higher relative density and hardness than those produced by vacuum sintering technology.展开更多
Despite the importance of aluminum alloys as candidate materials for applications in aerospace and automotive industries, very little work has been published on spark plasma and microwave processing of aluminum alloys...Despite the importance of aluminum alloys as candidate materials for applications in aerospace and automotive industries, very little work has been published on spark plasma and microwave processing of aluminum alloys. In the present work, the possibility was explored to process A12124 and A16061 alloys by spark plasma and microwave sintering techniques, and the microstructures and properties were compared. The alloys were sintered for 20 rain at 400, 450, and 500℃. It is found that compared to microwave sintering, spark plasma sintering is an effective way to obtain homogenous, dense, and hard alloys. Fully dense （100%） A16061 and A12124 alloys were obtained by spark plasma sintering for 20 rain at 450 and 500℃, respectively. Maximum relative densities were achieved for A16061 （92.52%） and A12124 （93.52%） alloys by microwave sintering at 500℃for 20 min. The Vickers microhardness of spark plasma sintered samples increases with the increase of sintering temperature from 400 to 500℃, and reaches the values of Hv 70.16 and Hv 117.10 for A16061 and A12124 alloys, respectively. For microwave siutered samples, the microhardness increases with the increase of sintering temperature from 400 to 450℃, and then decreases with the further increase of sintering temperature to 500~C.展开更多
To investigate the microwave effect on the WC–Co alloys,WC–8 wt%Co alloy was fabricated by microwave sintering(MWS)in this paper.The results show that decarburization layer forms on the surface of the microwave-sint...To investigate the microwave effect on the WC–Co alloys,WC–8 wt%Co alloy was fabricated by microwave sintering(MWS)in this paper.The results show that decarburization layer forms on the surface of the microwave-sintered samples.WC grain coarsening in the core area is strongly suppressed by the decarburization effect.In addition,the microstructure of the MWS-fabri-cated alloy was compared to that of the alloy sintered by vacuum sintering(VS).Microstructural investigations by transmission electron microscopy(TEM)and energy dis-persive spectroscopy(EDS)show that more tungsten(29.50 wt%)is dissolved in the cobalt binder phase in microwave-sintered alloy than that in the vacuum-sintered samples.Finally,the formation mechanism of the surface layer by skin effect was discussed.展开更多
Using the microwave sintering technology, the effects of phosphorus （P） additions on the microstructure and properties of the ultrafine WC-10Co alloys were investigated. The experimental results show that with only ...Using the microwave sintering technology, the effects of phosphorus （P） additions on the microstructure and properties of the ultrafine WC-10Co alloys were investigated. The experimental results show that with only 0.3wt% P additions, full density WC-10Co cermets were obtained at temperature of 1250℃, which is 70 ℃ lower than that of the undoped counterparts. Lower sintering temperature can result in finer WC grain growth; therefore, the P-doped WC-10Co alloys exhibited higher hardness than the undoped ones. But at the same time, P doping could lead to sacrifice of fracture toughness ofWC-10Co cemented carbides.展开更多
Nd3＋ substituted spinel ferrites with formula MgxCd1-xNd0.03Fe1.97O4（x = 0.0.2,0.4,0.6.0.8 and 1.0）were prepared by oxalate co-precipitation method using novel microwave sintering technique. AR grade sulphates were...Nd3＋ substituted spinel ferrites with formula MgxCd1-xNd0.03Fe1.97O4（x = 0.0.2,0.4,0.6.0.8 and 1.0）were prepared by oxalate co-precipitation method using novel microwave sintering technique. AR grade sulphates were used as starting chemicals. The samples were sintered at optimized power of 70 W for10 min in a microwave oven（800 W）. The structural analysis of these samples was done by using X-ray diffraction, scanning electron microscope and Fourier transform IR techniques. The XRD analysis of the synthesized ferrite confirms the formation of cubic spinel structure of ferrite. The influence of Nd3＋substitution on various structural parameters of Mg-Cd ferrites was reported. IR study indicates the spectra contain two intense absorption bands around 600 and 400 cm^（-1） in addition with four extra bands. The magnetic properties of all ferrites were studied by using a vibration sample magnetometer.The crystallite and grain size dependant magnetic properties are observed. The composition Mg_（0.6）Cd_（0.4）Nd_（0.03）Fe_（1.97）O_4 has better magnetic properties that can be used in recording media. The fast synthesis of spinel ferrites is yielded due to use of the microwave sintering technique.展开更多
Ca0.6La0.2667TiO3 ceramics were prepared by conventional and microwave sintering techniques and their sinterability, microstructure, and microwave dielectric properties were investigated in detail for comparison. Dens...Ca0.6La0.2667TiO3 ceramics were prepared by conventional and microwave sintering techniques and their sinterability, microstructure, and microwave dielectric properties were investigated in detail for comparison. Densified Ca0.6La0.E667TiO3 ceramics were obtained by microwave sintering at 1350℃ for 30 min and by conventional sintering at 1450℃ for 4 h. An unusual phenomenon was found that some larger grains （grain size range： 8-10 pan） inclined to assemble in one area but some smaller ones （grain size range： 2-4 μm） inclined to gather in another area in the microwave sintered ceramics. The microwave dielectric properties of Ca0.6La0.2667TiO3 ceramics prepared by micro- wave sintering at 1350℃ were as follows＂ dielectric constant （er） = 119.6, quality factor （Qf） = 17858.5 GHz, and temperature coefficient of resonant fi＇equency （rf）= 155.5 ppm/℃. In contrast, the microwave dielectric properties of the ceramics prepared by conventional sintering at 1450℃ were er = 117.4, Qf= 13375 GHz, and rf= 217.2 ppm/℃.展开更多
In this communication,the electrical conductivities and thermal expansion studies of microwave sintered co-doped ceria Ce_(0.8)Y_(0.2-x)Dy_(x)O_(2-δ)(x=0,0.05,0.10,0.15 and 0.20) solid electrolyte materials for inter...In this communication,the electrical conductivities and thermal expansion studies of microwave sintered co-doped ceria Ce_(0.8)Y_(0.2-x)Dy_(x)O_(2-δ)(x=0,0.05,0.10,0.15 and 0.20) solid electrolyte materials for intermediate temperature solid oxide fuel cells(IT-SOFCs)synthesized by sol-gel auto-combustion method were discussed.Microwave sintering at 1300℃ for 30 min was used for making dense powder compacts.The relative densities of all the samples are noticed above 95%.Raman spectrum was characterized by the presence of a very strong band near 460 cm^(-1),which along with X-ray diffraction(XRD) analysis ascertain the sample formation with a single-phase cubic fluorite structure.The lattice parameter values were calculated from XRD patterns.SEM images show nearly uniform grains with distinct grain boundaries.The thermal expansion coefficients(TECs) are found to vary linearly with temperature and were measured in the range from 14.15 to 13.20×10^(-6)℃^(-1).The investigation on total ionic conductivity(TIC) was executed with variation in dopant concentration and relative oxygen vacancies.The impedance analysis reveals that the sample Ce_(0.80)Y_(0.10)Dy_(0.10)O_(2-δ) displays the highest TIC,i.e.,7.5×10^(-3) S·cm^(-1) at 500℃ and minimum activation energy 0.90 eV compared to others.With the highest TIC and minimum activation energy,the Ce_(0.80)Y_(0.10)Dy_(0.10)O_(2-δ)might be the possible material as the solid electrolyte in intermediate temperature SOFCs.展开更多
In this study,the densification and microstructure evolution of microwave sintered(Ti,W,Mo,V)CN-30 wt%Co cermets,which was prepared from electroless cobalt-coated submicron(Ti,W,Mo,V)CN powders,were investigated.The m...In this study,the densification and microstructure evolution of microwave sintered(Ti,W,Mo,V)CN-30 wt%Co cermets,which was prepared from electroless cobalt-coated submicron(Ti,W,Mo,V)CN powders,were investigated.The microwave sintering of mechanical milled powders as well as the conventional sintering of mechanical milled powders and Co-coated(Ti,M)CN powders was conducted as a comparison.Experimental results indicate that a slight densification is observed at sintering temperature of≤1100℃followed by a sharp shrinkage at the temperature range of 1200-1350℃due to the substantial formation of liquid phase at 1200℃.The 98.5%densification is obtained at 1375℃.Moreover,the samples sintered at 1375℃for 10 min have the micro structure with fine and homogeneous grains of about 700 nm.Compared to mechanical milling,electroless cobalt plating suppresses coalescence of neighboring grain at the solid-state sintering stage,thereby inhibiting grain growth.The mechanical properties of samples sintered at different temperatures for varied holding time were also discussed.展开更多
The desulfurater(BaAl2O4) was successfully synthesized with BaCO3 and Al(OH)3 powders as raw materials by microwave sintering method.The mass loss of raw materials and the characterization of the outcome were investig...The desulfurater(BaAl2O4) was successfully synthesized with BaCO3 and Al(OH)3 powders as raw materials by microwave sintering method.The mass loss of raw materials and the characterization of the outcome were investigated by means of TG-DSC,XRD and optical microscopy.The reaction mechanism was discussed.The experimental results show that synthesized BaAl2O4 by microwave sintering method is feasible.Compared with conventional sintering method,microwave sintering is a better way to synthesize BaAl2O4 with advantages of low temperature sintering,short time sintering and high synthesis rate.展开更多
The effects of microwave sintering and conventional H2 sintering on the microstructure and properties of W-15Cu alloy using ultrafine W-15Cu composite powder fabricated by spray drying ＆ calcining-continuous reductio...The effects of microwave sintering and conventional H2 sintering on the microstructure and properties of W-15Cu alloy using ultrafine W-15Cu composite powder fabricated by spray drying ＆ calcining-continuous reduction technology were investigated. In comparison to the conventional HE sintering processing, microwave sintering to W-15Cu can be achieved at lower sintering temperature and shorter sintering time. Furthermore, higher performances in microwave sintered compacts were obtained, but high microwave sintering temperature or long microwave sintering time could result in coarser microstructures.展开更多
Composite powders of nanocrystalline WC-10Co （15wt%）,Y2O3 （8mol%） stabilized nanocrystalline ZrO2 （30wt%）,industrial cobalt powder （4.5wt%） and submicron Al2O3 （55wt%） composite powders were fabricated by hi...Composite powders of nanocrystalline WC-10Co （15wt%）,Y2O3 （8mol%） stabilized nanocrystalline ZrO2 （30wt%）,industrial cobalt powder （4.5wt%） and submicron Al2O3 （55wt%） composite powders were fabricated by high-energy ball-milling process.The nanocomposite powders were consolidated by microwave sintering process at temperature ranged 1300℃-1550℃ for 15min,respectively.The optimum consolidation conditions,such as temperature,were researched during microwave sintering process.Vickers Hardness of the consolidated cermets was measured by using a Vickers indentation test,and density of specimens was also determined by Archimedes＇ principle.Microwave sintering process could not only increase the density of Al2O3-ZrO2-WC-Co cermets and reduce the porosity,but also inhibit abnormal grain growth.展开更多
Microwave sintering method was carried out to prepare porous mullite composite. An insulation structure based on hybrid heating mode was well designed with the wall of mullite and the aided heaters of SiC. The obtaine...Microwave sintering method was carried out to prepare porous mullite composite. An insulation structure based on hybrid heating mode was well designed with the wall of mullite and the aided heaters of SiC. The obtained samples were characterized by XRD analysis, apparent porosity detection, and bending strength measurement. SEM was used to observe the microstructure of the sample. It is found that the porous mullite composite could be prepared through the microwave sintering within 2 h at relatively low temperatures around 1000 ℃. The lasted samples show comparatively superior properties to the products prepared by conventional processing.展开更多
基金Funded by the Key Research and Development Projects of Anhui Province(No.2022a05020026)the Key Technologies R&D Program of CNBM(Nos.2021HX0809,2021HX1011)the Anhui Science and Technology Major Project(No.2021e03020009)。
文摘Iron phosphate based glass-ceramics with deliberately added Ce as an active nuclide simulant were prepared by microwave sintering.The sintering characteristics,including phases and structural evolution,and chemical durability were investigated.XRD showed that NaZr_(2)(PO_(4))_(3) and FePO_(4) became the main crystalline phases of glass-ceramics with increasing sintering temperature.SEM revealed the glass-ceramics compactness increased first and then decreased as sintering temperature increased.Raman spectrum showed that,as sintering temperature increased,the network structure of glass-ceramics changed from mainly containing orthophosphate and pyrophosphate to a single orthophosphate.After immersion for 28 days,LR_(Na),LR_(Zr) and LR_(Ce) of the glass-ceramics prepared at 1000℃ were as low as 3.64×10^(-5),0.25×10^(-9) and 5.70×10^(-9)g/m^(2)/d respectively.The results indicate that iron phosphate based glass-ceramics can be prepared by rapid microwave sintering of glass powders and there is a potential of employing such microwave sintering technique in processing of glass-ceramics nuclear waste form.
基金Project (51274107) supported by the National Natural Science Foundation of China
文摘WC-8Co cemented carbide samples were processed via microwave irradiation in a 2.45 GHz, high-power multi-mode microwave cavity. The densification of the compacts and the microstructures of the prepared alloys were studied. The results demonstrate that the liquid phase is formed around 1300 ℃ and nearly full densification is obtained at 1450 ℃ for 5 min via microwave irradiation. The microstructures of microwave sintered samples have finer and more uniform WC grains than those of vacuum sintered samples. Besides, the WC grain size and distribution are only decided by the sintering temperature. Holding time has negligible effects on them. No matter how holding time is, the mean grain size is 2.7 pan when the sintering temperature is kept at 1450 ℃.
基金Project (2008890) supported by the Scientific Research Foundation for the Returned Overseas Chinese Scholars,China
文摘Cemented tungsten carbide with ultra fine grains was prepared via microwave sintering.η phase（W3Co3C） was formed on the surface of the samples during the preparation process.Extra carbon black was premixed and the influence of carbon content on mechanical properties was studied.The results show that the maximum value of hardness and transverse rupture strength are HRA 93.2 and 3396 MPa respectively when the carbon black content is 0.45%.The microstructure investigated by SEM show that the WC grains growth mainly occurs during the early stage of microwave sintering by the coalescence of grains.
文摘Al−2CNTs−xAl2O3 nanocomposites were manufactured by a hybrid powder metallurgy and microwave sintering process.The correlation between process-induced microstructural features and the material properties including physical and mechanical properties as well as ultrasonic parameters was measured.It was found that physical properties including densification and physical dimensional changes were closely associated with the morphology and particle size of nanocomposite powders.The maximum density was obtained by extensive particle refinement at milling time longer than 8 h and Al2O3 content of 10 wt.%.Mechanical properties were controlled by Al2O3 content,dispersion of nano reinforcements and grain size.The optimum hardness and strength properties were achieved through incorporation of 10 wt.%Al2O3 and homogenous dispersion of CNTs and Al2O3 nanoparticles(NPs)at 12 h of milling which resulted in the formation of high density of dislocations and extensive grain size refinement.Also both longitudinal and shear velocities and attenuation increase linearly by increasing Al2O3 content and milling time.The variation of ultrasonic velocity and attenuation was attributed to the degree of dispersion of CNTs and Al2O3 and also less inter-particle spacing in the matrix.The larger Al2O3 content and more homogenous dispersion of CNTs and Al2O3 NPs at longer milling time exerted higher velocity and attenuation of ultrasonic wave.
基金Project(2017YFB0305601) supported by the National Key R&D Program of ChinaProjects(51874368,51274246) supported by the National Natural Science Foundation of China
文摘In order to prepare high-performance Mo with fine and homogeneous microstructure to meet the demand of high-technology applications such as metallurgical,mechanical,national defense,aerospace and electronics applications,the microwave sintering process and densification mechanism of Mo nanopowder were studied.In this experiment,Mo nanopowder and micropowder were used for conventional sintering and microwave sintering at different sintering temperatures and sintering time,respectively.The results showed that with the increase in the sintering temperature,the increase rates of the relative density and hardness increased rapidly at first and then slowed down.The relative density rapidly reached 95%,followed by a small change.Mo nanopowder with a relative density of 98.03% and average grain size of 3.6 μm was prepared by microwave sintering at 1873 K for30 min.According to the analysis of the sintering kinetics,its densification is attributed to the combination of volumetric diffusion and grain boundary diffusion mechanisms.The calculated sintering activation energy of Mo nanopowder was 203.65 kJ/mol,which was considerably lower than that in the conventional sintering,suggesting that the microwave sintering was beneficial to the enhancement in the atom diffusion and densification for the powder.The results confirm that the microwave sintering is a promising method to economically prepare molybdenum with high properties.
基金supported by the Science and Technology Plan Projects of Jiangxi Province (No. 2011BBE50010)the Project from the Jiangxi Province Key Laboratory of Copper Tungsten New Materials (No. 2011-TW-08)
文摘Steel-cemented WC was prepared by ball milling, cold compacting and microwave sintering with Fe powder as the matrix, WC as the hard phase and the addition of rare earth Y2O3. The results show that the interface of the WC particles and Fe matrix exhibits excellent wettability and liquidity when the microwave sintering temperature reaches 1,280℃. The density and mechanical properties of the steel bonded WC carbides could be greatly improved, the hard phases become finer and more uniform dispersed owing to the addition of Y2O3. With the increase of the Y2O3 contents, the grain becomes uniform and fine first, and then gathers and grows up. The relative density, microhardness and bending strength all rise first, reaching the maximum values of 97.29 %, HV1024 and 1,267.60 MPa at 0.5 % Y2O3, respectively, and then decrease. Moreover, the relative density and mechanical properties of the steel-cemented WC with nano-Y2O3 are higher than that with micron-Y2O3, which indicates that the effect of nano-Y2O3 is better than that of the micron-Y2O3.
基金The authors are grateful for the financial supports from the National Natural Science Foundation of China(51101085,51764041,51704167)the Aeronautical Science Foundation of China(2015ZF56027,2016ZF56020)+2 种基金the Opening Project of National Engineering Research Center for Powder Metallurgy of Titanium&Rare Metals,China(2019004)the Key Laboratory of Lightweight and High Strength Structural Materials of Jiangxi Province,China(20171BCD40003)the Jiangxi Provincial Natural Science Foundation,China(20202ACBL214011).
文摘To obtain the lightweight,high strength,and high damping capacity porous NiTi alloys,the microwave sintering coupled with the Mg space holder technique was employed to prepare the porous NiTi alloys.The microstructure,mechanical properties,phase transformation behavior,superelasticity,and damping capacity of the porous NiTi alloys were investigated.The results show that the porous NiTi alloys are mainly composed of the B2 NiTi phase with a few B19'NiTi phase as the sintering temperature is lower than or equal to 900℃.With increasing the sintering temperature,the porosities of the porous NiTi alloys gradually decrease and the compressive strength increases first,reaching the maximum value at 900℃,and then decreases.With increasing the Mg content from 1 wt.%to 7 wt.%,the porosities of the porous NiTi alloys increase from 37.8%to 47.1%,while the compressive strength decreases from 2058 to 1146 MPa.Compared with the NH4HCO3 space holder,the phase transformation behavior of the porous NiTi alloys prepared with Mg space holder changes,and all of the compressive strength,superelasticity,shape memory effect and damping capacity are greatly improved.
基金the financial support under the University Research Grant No. Q.J130000.3024. 00M57
文摘Porous Ti-23%Nb(mole fraction)shape memory alloys(SMAs)were prepared successfully by microwave sintering with excellent outer finishing(without space holder).The effects of microwave-sintering on the microstructure,phase composition,phase-transformation temperature,mechanical properties and shape-memory effect were investigated.The results show that the density and size of porosity vary based on the sintering time and temperature,in which the smallest size and the most uniform pore shape are exhibited with Ti-23%Nb SMA after being sintered at 900°C for 30 min.The microstructure of porous Ti-Nb SMA consists of predominantα',α,andβphases in needle-like and plate-like morphologies,and their volume fractions vary based on the sintering time and temperature.Theβphase represents the largest phase due to the higher content ofβstabilizer element with little intensities ofαandα'phases.The highest ultimate strength and its strain are indicated for the sample sintered at 900°C for 30 min,while the best superelasticity is for the sample sintered at 1200°C for 30 min.The low-elastic modulus enables these alloys to avoid the problem of“stress shielding”.Therefore,microwave heating can be employed to sinter Ti-alloys for biomedical applications and improve the mechanical properties of these alloys.
基金supported by the Hunan Provincial Natural Science Fund for Distinguished Young Scholars of China(No.08JJ1007)the Hunan Provincial Key Science Research Program of China(No.2008GK2009)the Scientific Research Fund of Fujian Provincial Education Department of China(No.JK2009029)
文摘Ultra-fine titanium carbonitride （TiCN） matrix materials with a grain size less than 1μm were successfully prepared by vacuum microwave sintering. The milling process for raw TiCN particles and the microstructure and properties of cermets produced with a composition of 15wt.%WC-17wt.%（Co＋Ni）-9wt.%Mo2C-59wt.%Ti0.TN0.3 and sintered by vacuum microwave were analyzed by scanning electron microscopy （SEM） and X-ray diffraction （XRD）. The results show that a ball-to-powder mass ratio of 8：1 and a milling time of 50 h provided appropriate conditions for the production of ultra-fine TiCN solid solution powders. The use of vacuum microwave sintering produced cermets with much finer grain and black core structures and higher relative density and hardness than those produced by vacuum sintering technology.
基金supported by the King Abdul Aziz City for Science and Technology (KACST) (No. ARP-28-122)
文摘Despite the importance of aluminum alloys as candidate materials for applications in aerospace and automotive industries, very little work has been published on spark plasma and microwave processing of aluminum alloys. In the present work, the possibility was explored to process A12124 and A16061 alloys by spark plasma and microwave sintering techniques, and the microstructures and properties were compared. The alloys were sintered for 20 rain at 400, 450, and 500℃. It is found that compared to microwave sintering, spark plasma sintering is an effective way to obtain homogenous, dense, and hard alloys. Fully dense （100%） A16061 and A12124 alloys were obtained by spark plasma sintering for 20 rain at 450 and 500℃, respectively. Maximum relative densities were achieved for A16061 （92.52%） and A12124 （93.52%） alloys by microwave sintering at 500℃for 20 min. The Vickers microhardness of spark plasma sintered samples increases with the increase of sintering temperature from 400 to 500℃, and reaches the values of Hv 70.16 and Hv 117.10 for A16061 and A12124 alloys, respectively. For microwave siutered samples, the microhardness increases with the increase of sintering temperature from 400 to 450℃, and then decreases with the further increase of sintering temperature to 500~C.
基金the National Natural Science Foundation of China(No.51274107)。
文摘To investigate the microwave effect on the WC–Co alloys,WC–8 wt%Co alloy was fabricated by microwave sintering(MWS)in this paper.The results show that decarburization layer forms on the surface of the microwave-sintered samples.WC grain coarsening in the core area is strongly suppressed by the decarburization effect.In addition,the microstructure of the MWS-fabri-cated alloy was compared to that of the alloy sintered by vacuum sintering(VS).Microstructural investigations by transmission electron microscopy(TEM)and energy dis-persive spectroscopy(EDS)show that more tungsten(29.50 wt%)is dissolved in the cobalt binder phase in microwave-sintered alloy than that in the vacuum-sintered samples.Finally,the formation mechanism of the surface layer by skin effect was discussed.
基金the National Key Technology R&D Program of MOST,China(2003BA328C)the National Natural Science Foundation of China(50472043)Natural Science Foundation of Hubei Province(2006ABA312,2006ABA316)
文摘Using the microwave sintering technology, the effects of phosphorus （P） additions on the microstructure and properties of the ultrafine WC-10Co alloys were investigated. The experimental results show that with only 0.3wt% P additions, full density WC-10Co cermets were obtained at temperature of 1250℃, which is 70 ℃ lower than that of the undoped counterparts. Lower sintering temperature can result in finer WC grain growth; therefore, the P-doped WC-10Co alloys exhibited higher hardness than the undoped ones. But at the same time, P doping could lead to sacrifice of fracture toughness ofWC-10Co cemented carbides.
文摘Nd3＋ substituted spinel ferrites with formula MgxCd1-xNd0.03Fe1.97O4（x = 0.0.2,0.4,0.6.0.8 and 1.0）were prepared by oxalate co-precipitation method using novel microwave sintering technique. AR grade sulphates were used as starting chemicals. The samples were sintered at optimized power of 70 W for10 min in a microwave oven（800 W）. The structural analysis of these samples was done by using X-ray diffraction, scanning electron microscope and Fourier transform IR techniques. The XRD analysis of the synthesized ferrite confirms the formation of cubic spinel structure of ferrite. The influence of Nd3＋substitution on various structural parameters of Mg-Cd ferrites was reported. IR study indicates the spectra contain two intense absorption bands around 600 and 400 cm^（-1） in addition with four extra bands. The magnetic properties of all ferrites were studied by using a vibration sample magnetometer.The crystallite and grain size dependant magnetic properties are observed. The composition Mg_（0.6）Cd_（0.4）Nd_（0.03）Fe_（1.97）O_4 has better magnetic properties that can be used in recording media. The fast synthesis of spinel ferrites is yielded due to use of the microwave sintering technique.
基金financially supported by A Priority Academic Program Development of Jiangsu Higher Education Institutions
文摘Ca0.6La0.2667TiO3 ceramics were prepared by conventional and microwave sintering techniques and their sinterability, microstructure, and microwave dielectric properties were investigated in detail for comparison. Densified Ca0.6La0.E667TiO3 ceramics were obtained by microwave sintering at 1350℃ for 30 min and by conventional sintering at 1450℃ for 4 h. An unusual phenomenon was found that some larger grains （grain size range： 8-10 pan） inclined to assemble in one area but some smaller ones （grain size range： 2-4 μm） inclined to gather in another area in the microwave sintered ceramics. The microwave dielectric properties of Ca0.6La0.2667TiO3 ceramics prepared by micro- wave sintering at 1350℃ were as follows＂ dielectric constant （er） = 119.6, quality factor （Qf） = 17858.5 GHz, and temperature coefficient of resonant fi＇equency （rf）= 155.5 ppm/℃. In contrast, the microwave dielectric properties of the ceramics prepared by conventional sintering at 1450℃ were er = 117.4, Qf= 13375 GHz, and rf= 217.2 ppm/℃.
基金financially supported by the University Grants Commission,New Delhi,India,under the scheme of Faculty Development Program (No.Lr.APKA028/001/XIIPLAN)。
文摘In this communication,the electrical conductivities and thermal expansion studies of microwave sintered co-doped ceria Ce_(0.8)Y_(0.2-x)Dy_(x)O_(2-δ)(x=0,0.05,0.10,0.15 and 0.20) solid electrolyte materials for intermediate temperature solid oxide fuel cells(IT-SOFCs)synthesized by sol-gel auto-combustion method were discussed.Microwave sintering at 1300℃ for 30 min was used for making dense powder compacts.The relative densities of all the samples are noticed above 95%.Raman spectrum was characterized by the presence of a very strong band near 460 cm^(-1),which along with X-ray diffraction(XRD) analysis ascertain the sample formation with a single-phase cubic fluorite structure.The lattice parameter values were calculated from XRD patterns.SEM images show nearly uniform grains with distinct grain boundaries.The thermal expansion coefficients(TECs) are found to vary linearly with temperature and were measured in the range from 14.15 to 13.20×10^(-6)℃^(-1).The investigation on total ionic conductivity(TIC) was executed with variation in dopant concentration and relative oxygen vacancies.The impedance analysis reveals that the sample Ce_(0.80)Y_(0.10)Dy_(0.10)O_(2-δ) displays the highest TIC,i.e.,7.5×10^(-3) S·cm^(-1) at 500℃ and minimum activation energy 0.90 eV compared to others.With the highest TIC and minimum activation energy,the Ce_(0.80)Y_(0.10)Dy_(0.10)O_(2-δ)might be the possible material as the solid electrolyte in intermediate temperature SOFCs.
基金financially supported by the Program for New Century Excellent Talents in University (No. NCET-13-0394)the Sichuan Provincial Science Research Program of China (No.2015GZ0051)the National Natural Science Foundation of China (No.51104103)
文摘In this study,the densification and microstructure evolution of microwave sintered(Ti,W,Mo,V)CN-30 wt%Co cermets,which was prepared from electroless cobalt-coated submicron(Ti,W,Mo,V)CN powders,were investigated.The microwave sintering of mechanical milled powders as well as the conventional sintering of mechanical milled powders and Co-coated(Ti,M)CN powders was conducted as a comparison.Experimental results indicate that a slight densification is observed at sintering temperature of≤1100℃followed by a sharp shrinkage at the temperature range of 1200-1350℃due to the substantial formation of liquid phase at 1200℃.The 98.5%densification is obtained at 1375℃.Moreover,the samples sintered at 1375℃for 10 min have the micro structure with fine and homogeneous grains of about 700 nm.Compared to mechanical milling,electroless cobalt plating suppresses coalescence of neighboring grain at the solid-state sintering stage,thereby inhibiting grain growth.The mechanical properties of samples sintered at different temperatures for varied holding time were also discussed.
基金Project(50264001) supported by the National Natural Science Foundation of ChinaProject(QKH-J-2008-2009) supported by Guizhou Science and Technology Department, China
文摘The desulfurater(BaAl2O4) was successfully synthesized with BaCO3 and Al(OH)3 powders as raw materials by microwave sintering method.The mass loss of raw materials and the characterization of the outcome were investigated by means of TG-DSC,XRD and optical microscopy.The reaction mechanism was discussed.The experimental results show that synthesized BaAl2O4 by microwave sintering method is feasible.Compared with conventional sintering method,microwave sintering is a better way to synthesize BaAl2O4 with advantages of low temperature sintering,short time sintering and high synthesis rate.
基金Funded by the Project for Science and Technology Plan of Wuhan City(200910321092)the Youth Science Plan for Light of the Morning Sun of Wuhan City (200750731270)
文摘The effects of microwave sintering and conventional H2 sintering on the microstructure and properties of W-15Cu alloy using ultrafine W-15Cu composite powder fabricated by spray drying ＆ calcining-continuous reduction technology were investigated. In comparison to the conventional HE sintering processing, microwave sintering to W-15Cu can be achieved at lower sintering temperature and shorter sintering time. Furthermore, higher performances in microwave sintered compacts were obtained, but high microwave sintering temperature or long microwave sintering time could result in coarser microstructures.
基金Funded by the Youth Science Plan for Light of the Morning Sun of Wuhan City (200750731270)
文摘Composite powders of nanocrystalline WC-10Co （15wt%）,Y2O3 （8mol%） stabilized nanocrystalline ZrO2 （30wt%）,industrial cobalt powder （4.5wt%） and submicron Al2O3 （55wt%） composite powders were fabricated by high-energy ball-milling process.The nanocomposite powders were consolidated by microwave sintering process at temperature ranged 1300℃-1550℃ for 15min,respectively.The optimum consolidation conditions,such as temperature,were researched during microwave sintering process.Vickers Hardness of the consolidated cermets was measured by using a Vickers indentation test,and density of specimens was also determined by Archimedes＇ principle.Microwave sintering process could not only increase the density of Al2O3-ZrO2-WC-Co cermets and reduce the porosity,but also inhibit abnormal grain growth.
基金Funded by the National Natural Science Foundation of China( Nos.50972132 and 51172213)
文摘Microwave sintering method was carried out to prepare porous mullite composite. An insulation structure based on hybrid heating mode was well designed with the wall of mullite and the aided heaters of SiC. The obtained samples were characterized by XRD analysis, apparent porosity detection, and bending strength measurement. SEM was used to observe the microstructure of the sample. It is found that the porous mullite composite could be prepared through the microwave sintering within 2 h at relatively low temperatures around 1000 ℃. The lasted samples show comparatively superior properties to the products prepared by conventional processing.
