Recently,an article was published on solid effect(SE)dynamic nuclear polarization(DNP)enhancement,where the au-thors reported achieving 1H enhancement factors up to 500 by increasing the microwave power at 9.4 T,marki...Recently,an article was published on solid effect(SE)dynamic nuclear polarization(DNP)enhancement,where the au-thors reported achieving 1H enhancement factors up to 500 by increasing the microwave power at 9.4 T,marking the highest SE enhancement to date[1].展开更多
The microwave wireless power transmission technologies for space solar power station are a crucial field in the international space sector,where various countries are competing in its development.This paper surveys th...The microwave wireless power transmission technologies for space solar power station are a crucial field in the international space sector,where various countries are competing in its development.This paper surveys the research experiments and development efforts related to space solar power stations and microwave wireless power transmission technologies worldwide.The objective is to assess the progress and current state of this technological foundation,determine the necessary focus for developing high-power microwave wireless power transmission technology,and provide clarity on the direction of future technology development in these areas.Finally,a distributed space solar power station plan that is immediately feasible is proposed.展开更多
In the last decade,space solar power satellites(SSPSs)have been conceived to support net-zero carbon emissions and have attracted considerable attention.Electric energy is transmitted to the ground via a microwave pow...In the last decade,space solar power satellites(SSPSs)have been conceived to support net-zero carbon emissions and have attracted considerable attention.Electric energy is transmitted to the ground via a microwave power beam,a technology known as microwave power transmission(MPT).Due to the vast transmission distance of tens of thousands of kilometers,the power transmitting antenna array must span up to 1 kilometer in diameter.At the same time,the size of the rectifying array on the ground should extend over a few kilometers.This makes the MPT system of SSPSs significantly larger than the existing aerospace engineering system.To design and operate a rational MPT system,comprehensive optimization is required.Taking the space MPT system engineering into consideration,a novel multi-objective optimization function is proposed and further analyzed.The multi-objective optimization problem is modeled mathematically.Beam collection efficiency(BCE)is the primary factor,followed by the thermal management capability.Some tapers,designed to solve the conflict between BCE and the thermal problem,are reviewed.In addition to these two factors,rectenna design complexity is included as a functional factor in the optimization objective.Weight coefficients are assigned to these factors to prioritize them.Radiating planar arrays with different aperture illumination fields are studied,and their performances are compared using the multi-objective optimization function.Transmitting array size,rectifying array size,transmission distance,and transmitted power remaine constant in various cases,ensuring fair comparisons.The analysis results show that the proposed optimization function is effective in optimizing and selecting the MPT system architecture.It is also noted that the multi-objective optimization function can be expanded to include other factors in the future.展开更多
An lnGaP/GaAs HBT microwave power transistor with on-chip parallel RC stabilization network is developed with a standard GaAs MMIC process. From the stability factor K, the device shows unconditional stability in a wi...An lnGaP/GaAs HBT microwave power transistor with on-chip parallel RC stabilization network is developed with a standard GaAs MMIC process. From the stability factor K, the device shows unconditional stability in a wide frequency range due to the RC network. The power characteristics of the device as measured by a loadpull system show that the large-signal performance of the power transistor is affected slightly by the RC network. Psat is 30dBm at 5.4GHz,and PldB is larger than 21.6dBm at llGHz. The stability of the device due to RC network is proved by a power combination circuit. This makes the power transistor very suitable for applications in microwavc high power ttBT amplifiers.展开更多
The structure and microwave characteristics of low-voltage SiGe power HBTs are given.With this structure,the device can operate in a low-voltage and high-current state.By using an interdigital emitter strip layout and...The structure and microwave characteristics of low-voltage SiGe power HBTs are given.With this structure,the device can operate in a low-voltage and high-current state.By using an interdigital emitter strip layout and the operating voltage ranging from 3 to 4V,the output power in Class C operation can reach 1 65W at 1GHz,with the gain of 8dB.The highest collector efficiency is 67 8% under 3V.展开更多
Circularly polarized rectennas operating at X-band are studied in this paper. The quasi-square patches fed by aperture coupling are used as the circularly polarized receiving antennas, which are easily matched and int...Circularly polarized rectennas operating at X-band are studied in this paper. The quasi-square patches fed by aperture coupling are used as the circularly polarized receiving antennas, which are easily matched and integrated with the circuits of rectennas. The double-layer structure not only minimizes the size of the rectennas but also decreases the effects of the circuits on the an- tenna. The receiving elements have broader bandwidth and higher gain than the single-layer patches. Two rectennas operating at 10GHz are designed, fabricated and measured. The voltage of 3.86V on a load of 200? is measured and a high RF-DC conversion efficiency of 75% is obtained at 9.98GHz. It is convenient for this kind of rectennas to form large arrays for high power applications.展开更多
This work presents an optimal design method of antenna aperture illumination for microwave power transmission with an annular collection area.The objective is to maximize the ratio of the power radiated on the annular...This work presents an optimal design method of antenna aperture illumination for microwave power transmission with an annular collection area.The objective is to maximize the ratio of the power radiated on the annular collection area to the total transmitted power.By formulating the aperture amplitude distribution through a summation of a special set of series,the optimal design problem can be reduced to finding the maximum ratio of two real quadratic forms.Based on the theory of matrices,the solution to the formulated optimization problem is to determine the largest characteristic value and its associated characteristic vector.To meet security requirements,the peak radiation levels outside the receiving area are considered to be extra constraints.A hybrid grey wolf optimizer and Nelder–Mead simplex method is developed to deal with this constrained optimization problem.In order to demonstrate the effectiveness of the proposed method,numerical experiments on continuous apertures are conducted;then,discrete arrays of isotropic elements are employed to validate the correctness of the optimized results.Finally,patch arrays are adopted to further verify the validity of the proposed method.展开更多
Electron cyclotron resonance （ECR） plasma was applied to enhance the direct current magnetron sputtering to prepare hydrogenated diamond-like carbon （H-DLC） films. For different microwave powers, both argon and hy...Electron cyclotron resonance （ECR） plasma was applied to enhance the direct current magnetron sputtering to prepare hydrogenated diamond-like carbon （H-DLC） films. For different microwave powers, both argon and hydrogen gas are introduced separately as the ECR working gas to investigate the influence of microwave power on the microstructure and electrical property of the H-DLC films deposited on P-type silicon substrates. A series of characterization methods including the Raman spectrum and atomic force microscopy are used. Results show that, within a certain range, the increase in microwave power affects the properties of the thin films, namely the sp3 ratio, the hardness, the nanoparticle size and the resistivity all increase while the roughness decreases with the increase in microwave power. The maximum of resistivity amounts to 1.1×10^9 Ω.cm. At the same time it is found that the influence of microwave power on the properties of H-DLC films is more pronounced when argon gas is applied as the ECR working gas, compared to hydrogen gas.展开更多
This study proposes a method for maximizing the beam collection efficiency(BCE)for a microwave power transmission system with multiple receiving targets in the radiative near-field region.The electric and magnetic fie...This study proposes a method for maximizing the beam collection efficiency(BCE)for a microwave power transmission system with multiple receiving targets in the radiative near-field region.The electric and magnetic fields of the transmitting array are calculated via the superposition principle.Through theoretical derivation,the BCE maximization problem is simplified into finding the maximum ratio of two real quadratic forms.Based on the theory of matrices,the optimal BCE and its corresponding excitations of the transmitting array can be determined by finding the largest characteristic value and its associated characteristic vector.In practice,the required power for multiple receiving targets may be different.To meet this requirement,a BCE optimization model is established,considering the constraints of the problem of allocable power for each receiving target.A hybrid grey wolf optimizer and Nelder-Mead simplex method is adopted to address the optimization problem.To verify the effectiveness of the proposed method,numerical experiments on focusing the power radiated on two parallel receiving targets are conducted first.Then,two rotating receiving targets are employed to show its universality.Finally,three and four receiving targets are adopted to further evaluate the validity of the proposed method.展开更多
The 6 MW/4.6 GHz lower hybrid current drive （LHCD） system will be set up on the experimental advanced superconducting tokamak （EAST） for achieving a steady-state op- eration. The high power and continuous wave （C...The 6 MW/4.6 GHz lower hybrid current drive （LHCD） system will be set up on the experimental advanced superconducting tokamak （EAST） for achieving a steady-state op- eration. The high power and continuous wave （CW） mode microwave test bench operating at 250 kW/4.6 GHz has already been finished, which can be used to simulate different kinds of high power microwave environments to test microwave components and units for the new LHCD sys- tem. The power control and data acquisition system on the test bench composed of power control, high reflected power protection and data acquisition function is described here in detail. Long- term operation of the test bench showed that the power control and data acquisition system is very stable and reliable.展开更多
A terminating type MEMS microwave power sensor based on the Seebeck effect and compatible with the GaAs MMIC process is presented. An electrothermal model is introduced to simulate the heat transfer behavior and tempe...A terminating type MEMS microwave power sensor based on the Seebeck effect and compatible with the GaAs MMIC process is presented. An electrothermal model is introduced to simulate the heat transfer behavior and temperature distribution. The sensor measured the microwave power from –20 to 20 dBm up to 20 GHz. The sensitivity of the sensor is 0.27 mV/mW at 20 GHz, and the input return loss is less than –26 dB over the entire experiment frequency range. In order to improve the sensitivity, four different types of coplanar waveguide （CPW） were designed and the sensitivity was significantly increased by about a factor of 2.展开更多
A Fourier equivalent model is introduced to research the thermal transfer behavior of a terminating-type MEMS microwave power sensor.The fabrication of this MEMS microwave power sensor is compatible with the GaAs MMIC...A Fourier equivalent model is introduced to research the thermal transfer behavior of a terminating-type MEMS microwave power sensor.The fabrication of this MEMS microwave power sensor is compatible with the GaAs MMIC process.Based on the Fourier equivalent model,the relationship between the sensitivity of a MEMS microwave power sensor and the length of thermopile is studied in particular.The power sensor is measured with an input power from 1 to 100 mW at 10 GHz,and the measurement results show that the power sensor has good input match characteristics and high linearity.The sensitivity calculated from a Fourier equivalent model is about 0.12,0.20 and 0.29 mV/mW with the length at 40,70 and 100μm,respectively,while the sensitivity of the measurement results is about 0.10,0.22 and 0.30 mV/mW,respectively,and the differences are below 0.02 mV/mW. The sensitivity expression based on the Fourier equivalent model is verified by the measurement results.展开更多
A wideband 8-12 GHz inline type microwave power sensor, which has both working and non-working states, is presented. The power sensor measures the microwave power coupled from a CPW line by a MEMS membrane. In order t...A wideband 8-12 GHz inline type microwave power sensor, which has both working and non-working states, is presented. The power sensor measures the microwave power coupled from a CPW line by a MEMS membrane. In order to reduce microwave losses during the non-working state, a new structure of working state transfer switches is proposed to realize the two working states. The fabrication of the power sensor with two working states is compatible with the GaAs MMIC （monolithic microwave integrated circuit） process. The experimental results show that the power sensor has an insertion loss of 0.18 dB during the non-working state and 0.24 dB during the working state at a frequency of 10 GHz. This means that no microwave power has been coupled from the CPW line during the non-working state.展开更多
A terminating type MEMS microwave power sensor based on the Seebeck effect and compatible with the GaAs MMIC process is presented.An electrothermal model is introduced to simulate the thermal time constant. An analyti...A terminating type MEMS microwave power sensor based on the Seebeck effect and compatible with the GaAs MMIC process is presented.An electrothermal model is introduced to simulate the thermal time constant. An analytical result,about 160 ms,of the thermal time constant from the non-stationary Fourier heat equations for the structure of the sensor is also given.The sensor measures the microwave power jumping from 15 to 20 dBm at a constant frequency 15 GHz,and the experimental thermal time constant result is 180 ms.The frequency is also changed from 20 to 10 GHz with a constant power 20 dBm,and the result is also 180 ms.Compared with the analytical and experimental results,the model is verified.展开更多
This paper reports that multi-recessed gate 4H-SiC MESFETs （metal semiconductor filed effect transistors） with a gate periphery of 5-mm are fabricated and characterized.The multi-recessed region under the gate termi...This paper reports that multi-recessed gate 4H-SiC MESFETs （metal semiconductor filed effect transistors） with a gate periphery of 5-mm are fabricated and characterized.The multi-recessed region under the gate terminal is applied to improve the gate-drain breakdown voltage and to alleviate the trapping induced instabilities by moving the current path away from the surface of the device.The experimental results demonstrate that microwave output power density,power gain and power-added efficiency for multi-finger 5-mm gate periphery SiC MESFETs with multi-recessed gate structure are about 29%, 1.1dB and 7% higher than those of conventional devices fabricated in this work using the same process.展开更多
In recent years, the effective conversion of organic wastes into valuable products has been a focus and difficulty in sustainable energy and environmental management. Organic wastes come from a wide range of sources, ...In recent years, the effective conversion of organic wastes into valuable products has been a focus and difficulty in sustainable energy and environmental management. Organic wastes come from a wide range of sources, and industrial and agricultural sources are the main sources of organic waste in China, which can be controlled by microwave pyrolysis technology. In microwave pyrolysis treatment, catalysts have been the key material, microwave absorber, and catalyst of the research hotspot in recent years. This paper summarises the typical influencing parameters of microwave pyrolysis (including microwave power, pyrolysis temperature and microwave absorber), and also summarises the various catalysts applied in microwave pyrolysis, and looks forward to the potential application prospect of pyrolysis products, and the future development direction.展开更多
The high power microwave （HPM） damage effect on the AIGaAs/InGaAs pseudomorphic high electron mobility transistor （pHEMT） is studied by simulation and experiments. Simulated results suggest that the HPM damage to ...The high power microwave （HPM） damage effect on the AIGaAs/InGaAs pseudomorphic high electron mobility transistor （pHEMT） is studied by simulation and experiments. Simulated results suggest that the HPM damage to pHEMT is due to device burn-out caused by the emerging current path and strong electric field beneath the gate. Besides, the results demonstrate that the damage power threshold decreases but the energy threshold slightly increases with the increase of pulse-width, indicating that HPM with longer pulse-width requires lower power density but more energy to cause the damage to pHEMT. The empirical formulas are proposed to describe the pulse-width dependence. Then the experimental data validate the pulse-width dependence and verify that the proposed formula P = 55τ^-0.06 is capable of quickly and accurately estimating the HPM damage susceptibility of pHEMT. Finally the interior observation of damaged samples by scanning electron microscopy （SEM） illustrates that the failure mechanism of the HPM damage to pHEMT is indeed device bum-out and the location beneath the gate near the source side is most susceptible to bum-out, which is in accordance with the simulated results.展开更多
In this paper, we present the damage effect and mechanism of high power microwave （HPM） on AIGaAs/GaAs pseudomorphic high-electron-mobility transistor （pHEMT） of low-noise amplifier （LNA）. A detailed investigati...In this paper, we present the damage effect and mechanism of high power microwave （HPM） on AIGaAs/GaAs pseudomorphic high-electron-mobility transistor （pHEMT） of low-noise amplifier （LNA）. A detailed investigation is carried out by simulation and experiment study. A two-dimensional electro-thermal model of the typical GaAs pHEMT induced by HPM is established in this paper. The simulation result reveals that avalanche breakdown, intrinsic excitation, and thermal breakdown all contribute to damage process. Heat accumulation occurs during the positive half cycle and the cylinder under the gate near the source side is most susceptible to burn-out. Experiment is carried out by injecting high power microwave into GaAs pHEMT LNA samples. It is found that the damage to LNA is because of the burn-out at first stage pHEMT. The interiors of the damaged samples are observed by scanning electron microscopy （SEM） and energy dispersive spectrometer （EDS）. Experimental results accord well with the simulation of our model.展开更多
While sufficient review articles exist on inductive short-range wireless power transfer(WPT),long-haul microwave WPT(MWPT)for solar power satellites,and ambient microwave wireless energy harvesting(MWEH)in urban areas...While sufficient review articles exist on inductive short-range wireless power transfer(WPT),long-haul microwave WPT(MWPT)for solar power satellites,and ambient microwave wireless energy harvesting(MWEH)in urban areas,few studies focus on the fundamental modeling and related design automation of receiver systems.This article reviews the development of MWPT and MWEH receivers,with a focus on rectenna design automation.A novel rectifier model capable of accurately modeling the rectification process under both high and low input power is presented.The model reveals the theoretical boundary of radio frequency-to-direct current(dc)power conversion efficiency and,most importantly,enables an automated system design.The automated rectenna design flow is sequential,with the minimal engagement of iterative optimization.It covers the design automation of every module(i.e.,rectifiers,matching circuits,antennae,and dc–dc converters).Scaling-up of the technique to large rectenna arrays is also possible,where the challenges in array partitioning and power combining are briefly discussed.In addition,several cutting-edge rectenna techniques for MWPT and MWEH are reviewed,including the dynamic range extension technique,the harmonics-based retro-directive technique,and the simultaneous wireless information and power transfer technique,which can be good complements to the presented automated design methodology.展开更多
The experimental study of ultra-wideband (UWB) technology, its generation and on-line measurement are presented. An experimental repetitive UWB system is designed, manufactured, and tested. High-pressure spark gap swi...The experimental study of ultra-wideband (UWB) technology, its generation and on-line measurement are presented. An experimental repetitive UWB system is designed, manufactured, and tested. High-pressure spark gap switch and its components, as well as oil spark gap switch are studied experimentally on the system. Experimental results indicate that the system operates at a 200 pps repetitive rate with a stable performance. 100 MW peak power UWB pulses are obtained on the system. Fast-time response capacitive divider is designed and fabricated, allowing for an accurate measurement of the high power UWB signal. The main issues related to the design of the switch and the UWB signal online measurement are discussed.展开更多
文摘Recently,an article was published on solid effect(SE)dynamic nuclear polarization(DNP)enhancement,where the au-thors reported achieving 1H enhancement factors up to 500 by increasing the microwave power at 9.4 T,marking the highest SE enhancement to date[1].
基金Entrusted Fund of National Institute of Information and Communications Technology(NICT),Japan(JPJ012368C02401)。
文摘The microwave wireless power transmission technologies for space solar power station are a crucial field in the international space sector,where various countries are competing in its development.This paper surveys the research experiments and development efforts related to space solar power stations and microwave wireless power transmission technologies worldwide.The objective is to assess the progress and current state of this technological foundation,determine the necessary focus for developing high-power microwave wireless power transmission technology,and provide clarity on the direction of future technology development in these areas.Finally,a distributed space solar power station plan that is immediately feasible is proposed.
文摘In the last decade,space solar power satellites(SSPSs)have been conceived to support net-zero carbon emissions and have attracted considerable attention.Electric energy is transmitted to the ground via a microwave power beam,a technology known as microwave power transmission(MPT).Due to the vast transmission distance of tens of thousands of kilometers,the power transmitting antenna array must span up to 1 kilometer in diameter.At the same time,the size of the rectifying array on the ground should extend over a few kilometers.This makes the MPT system of SSPSs significantly larger than the existing aerospace engineering system.To design and operate a rational MPT system,comprehensive optimization is required.Taking the space MPT system engineering into consideration,a novel multi-objective optimization function is proposed and further analyzed.The multi-objective optimization problem is modeled mathematically.Beam collection efficiency(BCE)is the primary factor,followed by the thermal management capability.Some tapers,designed to solve the conflict between BCE and the thermal problem,are reviewed.In addition to these two factors,rectenna design complexity is included as a functional factor in the optimization objective.Weight coefficients are assigned to these factors to prioritize them.Radiating planar arrays with different aperture illumination fields are studied,and their performances are compared using the multi-objective optimization function.Transmitting array size,rectifying array size,transmission distance,and transmitted power remaine constant in various cases,ensuring fair comparisons.The analysis results show that the proposed optimization function is effective in optimizing and selecting the MPT system architecture.It is also noted that the multi-objective optimization function can be expanded to include other factors in the future.
文摘An lnGaP/GaAs HBT microwave power transistor with on-chip parallel RC stabilization network is developed with a standard GaAs MMIC process. From the stability factor K, the device shows unconditional stability in a wide frequency range due to the RC network. The power characteristics of the device as measured by a loadpull system show that the large-signal performance of the power transistor is affected slightly by the RC network. Psat is 30dBm at 5.4GHz,and PldB is larger than 21.6dBm at llGHz. The stability of the device due to RC network is proved by a power combination circuit. This makes the power transistor very suitable for applications in microwavc high power ttBT amplifiers.
文摘The structure and microwave characteristics of low-voltage SiGe power HBTs are given.With this structure,the device can operate in a low-voltage and high-current state.By using an interdigital emitter strip layout and the operating voltage ranging from 3 to 4V,the output power in Class C operation can reach 1 65W at 1GHz,with the gain of 8dB.The highest collector efficiency is 67 8% under 3V.
基金Supported by the Development Fund of Shanghai Edu-cation Committee and Shanghai Leading Academic Dis-cipline Project (No.T0102)
文摘Circularly polarized rectennas operating at X-band are studied in this paper. The quasi-square patches fed by aperture coupling are used as the circularly polarized receiving antennas, which are easily matched and integrated with the circuits of rectennas. The double-layer structure not only minimizes the size of the rectennas but also decreases the effects of the circuits on the an- tenna. The receiving elements have broader bandwidth and higher gain than the single-layer patches. Two rectennas operating at 10GHz are designed, fabricated and measured. The voltage of 3.86V on a load of 200? is measured and a high RF-DC conversion efficiency of 75% is obtained at 9.98GHz. It is convenient for this kind of rectennas to form large arrays for high power applications.
基金supported in part by the National Key Research and Development Program of China(2021YFB3900300)in part by the National Natural Science Foundation of China(62201416)+2 种基金in part by the Fundamental Research Funds for the Central Universities(QTZX23070)in part by the Qin Chuang Yuan High-Level Innovative and Entrepreneurial Talents Project(QCYRCXM-2022-314)in part by Singapore Ministry of Education Academic Research Fund Tier 1。
文摘This work presents an optimal design method of antenna aperture illumination for microwave power transmission with an annular collection area.The objective is to maximize the ratio of the power radiated on the annular collection area to the total transmitted power.By formulating the aperture amplitude distribution through a summation of a special set of series,the optimal design problem can be reduced to finding the maximum ratio of two real quadratic forms.Based on the theory of matrices,the solution to the formulated optimization problem is to determine the largest characteristic value and its associated characteristic vector.To meet security requirements,the peak radiation levels outside the receiving area are considered to be extra constraints.A hybrid grey wolf optimizer and Nelder–Mead simplex method is developed to deal with this constrained optimization problem.In order to demonstrate the effectiveness of the proposed method,numerical experiments on continuous apertures are conducted;then,discrete arrays of isotropic elements are employed to validate the correctness of the optimized results.Finally,patch arrays are adopted to further verify the validity of the proposed method.
基金supported by Shenzhen Key Laboratory of Sensors Technology Open Fund of China (Nos.SST200908, SST200911)
文摘Electron cyclotron resonance （ECR） plasma was applied to enhance the direct current magnetron sputtering to prepare hydrogenated diamond-like carbon （H-DLC） films. For different microwave powers, both argon and hydrogen gas are introduced separately as the ECR working gas to investigate the influence of microwave power on the microstructure and electrical property of the H-DLC films deposited on P-type silicon substrates. A series of characterization methods including the Raman spectrum and atomic force microscopy are used. Results show that, within a certain range, the increase in microwave power affects the properties of the thin films, namely the sp3 ratio, the hardness, the nanoparticle size and the resistivity all increase while the roughness decreases with the increase in microwave power. The maximum of resistivity amounts to 1.1×10^9 Ω.cm. At the same time it is found that the influence of microwave power on the properties of H-DLC films is more pronounced when argon gas is applied as the ECR working gas, compared to hydrogen gas.
基金the national Natural ScienceFoundation of China(No.62201416&No.U2241247)the Fundamental Research Funds for the Central Universities(No.QTZX23070&QTZX24002)+1 种基金the Qin Chuang Yuan High-Level Innovative and Entrepreneurial Talents(No.QCYRCXM-2022-314)the Natural Science Basic Research Program ofShaanxi(No.2022JC-DW-01).
文摘This study proposes a method for maximizing the beam collection efficiency(BCE)for a microwave power transmission system with multiple receiving targets in the radiative near-field region.The electric and magnetic fields of the transmitting array are calculated via the superposition principle.Through theoretical derivation,the BCE maximization problem is simplified into finding the maximum ratio of two real quadratic forms.Based on the theory of matrices,the optimal BCE and its corresponding excitations of the transmitting array can be determined by finding the largest characteristic value and its associated characteristic vector.In practice,the required power for multiple receiving targets may be different.To meet this requirement,a BCE optimization model is established,considering the constraints of the problem of allocable power for each receiving target.A hybrid grey wolf optimizer and Nelder-Mead simplex method is adopted to address the optimization problem.To verify the effectiveness of the proposed method,numerical experiments on focusing the power radiated on two parallel receiving targets are conducted first.Then,two rotating receiving targets are employed to show its universality.Finally,three and four receiving targets are adopted to further evaluate the validity of the proposed method.
基金supported by National Magnetic Confinement Fusion Science Program of China(No.2010GB105001)
文摘The 6 MW/4.6 GHz lower hybrid current drive （LHCD） system will be set up on the experimental advanced superconducting tokamak （EAST） for achieving a steady-state op- eration. The high power and continuous wave （CW） mode microwave test bench operating at 250 kW/4.6 GHz has already been finished, which can be used to simulate different kinds of high power microwave environments to test microwave components and units for the new LHCD sys- tem. The power control and data acquisition system on the test bench composed of power control, high reflected power protection and data acquisition function is described here in detail. Long- term operation of the test bench showed that the power control and data acquisition system is very stable and reliable.
基金supported by the National Natural Science Foundation of China (No. 60676043)the National High Technology Research and Development Program of China (No. 2007AA04Z328)
文摘A terminating type MEMS microwave power sensor based on the Seebeck effect and compatible with the GaAs MMIC process is presented. An electrothermal model is introduced to simulate the heat transfer behavior and temperature distribution. The sensor measured the microwave power from –20 to 20 dBm up to 20 GHz. The sensitivity of the sensor is 0.27 mV/mW at 20 GHz, and the input return loss is less than –26 dB over the entire experiment frequency range. In order to improve the sensitivity, four different types of coplanar waveguide （CPW） were designed and the sensitivity was significantly increased by about a factor of 2.
基金Project supported by the National Natural Science Foundation of China(Nos.61076108,60976094,60676043)the National High Technology Research and Development Program of China(No.2007AA04Z328)
文摘A Fourier equivalent model is introduced to research the thermal transfer behavior of a terminating-type MEMS microwave power sensor.The fabrication of this MEMS microwave power sensor is compatible with the GaAs MMIC process.Based on the Fourier equivalent model,the relationship between the sensitivity of a MEMS microwave power sensor and the length of thermopile is studied in particular.The power sensor is measured with an input power from 1 to 100 mW at 10 GHz,and the measurement results show that the power sensor has good input match characteristics and high linearity.The sensitivity calculated from a Fourier equivalent model is about 0.12,0.20 and 0.29 mV/mW with the length at 40,70 and 100μm,respectively,while the sensitivity of the measurement results is about 0.10,0.22 and 0.30 mV/mW,respectively,and the differences are below 0.02 mV/mW. The sensitivity expression based on the Fourier equivalent model is verified by the measurement results.
基金Project supported by the National Natural Science Foundation of China(No.60676043)the National High Technology Research and Development Program of China(No.2007AA04Z328).
文摘A wideband 8-12 GHz inline type microwave power sensor, which has both working and non-working states, is presented. The power sensor measures the microwave power coupled from a CPW line by a MEMS membrane. In order to reduce microwave losses during the non-working state, a new structure of working state transfer switches is proposed to realize the two working states. The fabrication of the power sensor with two working states is compatible with the GaAs MMIC （monolithic microwave integrated circuit） process. The experimental results show that the power sensor has an insertion loss of 0.18 dB during the non-working state and 0.24 dB during the working state at a frequency of 10 GHz. This means that no microwave power has been coupled from the CPW line during the non-working state.
基金supported by the National Natural Science Foundation of China(No.60676043)the National High Technology Research and Development Program of China(No.2007AA04Z328)
文摘A terminating type MEMS microwave power sensor based on the Seebeck effect and compatible with the GaAs MMIC process is presented.An electrothermal model is introduced to simulate the thermal time constant. An analytical result,about 160 ms,of the thermal time constant from the non-stationary Fourier heat equations for the structure of the sensor is also given.The sensor measures the microwave power jumping from 15 to 20 dBm at a constant frequency 15 GHz,and the experimental thermal time constant result is 180 ms.The frequency is also changed from 20 to 10 GHz with a constant power 20 dBm,and the result is also 180 ms.Compared with the analytical and experimental results,the model is verified.
基金Project supported by Major State Basic Research Development Program of China (Grant No 51327010101)
文摘This paper reports that multi-recessed gate 4H-SiC MESFETs （metal semiconductor filed effect transistors） with a gate periphery of 5-mm are fabricated and characterized.The multi-recessed region under the gate terminal is applied to improve the gate-drain breakdown voltage and to alleviate the trapping induced instabilities by moving the current path away from the surface of the device.The experimental results demonstrate that microwave output power density,power gain and power-added efficiency for multi-finger 5-mm gate periphery SiC MESFETs with multi-recessed gate structure are about 29%, 1.1dB and 7% higher than those of conventional devices fabricated in this work using the same process.
文摘In recent years, the effective conversion of organic wastes into valuable products has been a focus and difficulty in sustainable energy and environmental management. Organic wastes come from a wide range of sources, and industrial and agricultural sources are the main sources of organic waste in China, which can be controlled by microwave pyrolysis technology. In microwave pyrolysis treatment, catalysts have been the key material, microwave absorber, and catalyst of the research hotspot in recent years. This paper summarises the typical influencing parameters of microwave pyrolysis (including microwave power, pyrolysis temperature and microwave absorber), and also summarises the various catalysts applied in microwave pyrolysis, and looks forward to the potential application prospect of pyrolysis products, and the future development direction.
基金Project supported by the National Basic Research Program of China(Grant No.2014CB339900)the National Natural Science Foundation of China(Grant No.60776034)
文摘The high power microwave （HPM） damage effect on the AIGaAs/InGaAs pseudomorphic high electron mobility transistor （pHEMT） is studied by simulation and experiments. Simulated results suggest that the HPM damage to pHEMT is due to device burn-out caused by the emerging current path and strong electric field beneath the gate. Besides, the results demonstrate that the damage power threshold decreases but the energy threshold slightly increases with the increase of pulse-width, indicating that HPM with longer pulse-width requires lower power density but more energy to cause the damage to pHEMT. The empirical formulas are proposed to describe the pulse-width dependence. Then the experimental data validate the pulse-width dependence and verify that the proposed formula P = 55τ^-0.06 is capable of quickly and accurately estimating the HPM damage susceptibility of pHEMT. Finally the interior observation of damaged samples by scanning electron microscopy （SEM） illustrates that the failure mechanism of the HPM damage to pHEMT is indeed device bum-out and the location beneath the gate near the source side is most susceptible to bum-out, which is in accordance with the simulated results.
基金supported by the National Basic Research Program of China(Grant No.2014CB339900)the Open Fund of Key Laboratory of Complex Electromagnetic Environment Science and TechnologyChina Academy of Engineering Physics(Grant No.2015-0214.XY.K)
文摘In this paper, we present the damage effect and mechanism of high power microwave （HPM） on AIGaAs/GaAs pseudomorphic high-electron-mobility transistor （pHEMT） of low-noise amplifier （LNA）. A detailed investigation is carried out by simulation and experiment study. A two-dimensional electro-thermal model of the typical GaAs pHEMT induced by HPM is established in this paper. The simulation result reveals that avalanche breakdown, intrinsic excitation, and thermal breakdown all contribute to damage process. Heat accumulation occurs during the positive half cycle and the cylinder under the gate near the source side is most susceptible to burn-out. Experiment is carried out by injecting high power microwave into GaAs pHEMT LNA samples. It is found that the damage to LNA is because of the burn-out at first stage pHEMT. The interiors of the damaged samples are observed by scanning electron microscopy （SEM） and energy dispersive spectrometer （EDS）. Experimental results accord well with the simulation of our model.
基金supported by the Singapore Ministry of Education Academic Research Fund Tier 1。
文摘While sufficient review articles exist on inductive short-range wireless power transfer(WPT),long-haul microwave WPT(MWPT)for solar power satellites,and ambient microwave wireless energy harvesting(MWEH)in urban areas,few studies focus on the fundamental modeling and related design automation of receiver systems.This article reviews the development of MWPT and MWEH receivers,with a focus on rectenna design automation.A novel rectifier model capable of accurately modeling the rectification process under both high and low input power is presented.The model reveals the theoretical boundary of radio frequency-to-direct current(dc)power conversion efficiency and,most importantly,enables an automated system design.The automated rectenna design flow is sequential,with the minimal engagement of iterative optimization.It covers the design automation of every module(i.e.,rectifiers,matching circuits,antennae,and dc–dc converters).Scaling-up of the technique to large rectenna arrays is also possible,where the challenges in array partitioning and power combining are briefly discussed.In addition,several cutting-edge rectenna techniques for MWPT and MWEH are reviewed,including the dynamic range extension technique,the harmonics-based retro-directive technique,and the simultaneous wireless information and power transfer technique,which can be good complements to the presented automated design methodology.
文摘The experimental study of ultra-wideband (UWB) technology, its generation and on-line measurement are presented. An experimental repetitive UWB system is designed, manufactured, and tested. High-pressure spark gap switch and its components, as well as oil spark gap switch are studied experimentally on the system. Experimental results indicate that the system operates at a 200 pps repetitive rate with a stable performance. 100 MW peak power UWB pulses are obtained on the system. Fast-time response capacitive divider is designed and fabricated, allowing for an accurate measurement of the high power UWB signal. The main issues related to the design of the switch and the UWB signal online measurement are discussed.
