Molten salt reactors,being the only reactor type among Generation Ⅳ advanced nuclear reactors that utilize liquid fuels,offer inherent safety,high-temperature,and low-pressure operation,as well as the capability for ...Molten salt reactors,being the only reactor type among Generation Ⅳ advanced nuclear reactors that utilize liquid fuels,offer inherent safety,high-temperature,and low-pressure operation,as well as the capability for online fuel reprocessing.However,the fuel-salt flow results in the decay of delayed neutron precursors(DNPs)outside the core,causing fluctuations in the effective delayed neutron fraction and consequently impacting the reactor reactivity.Particularly in accident scenarios—such as a combined pump shutdown and the inability to rapidly scram the reactor—the sole reliance on negative temperature feedback may cause a significant increase in core temperature,posing a threat to reactor safety.To address these problems,this paper introduces an innovative design for a passive fluid-driven suspended control rod(SCR)to dynamically compensate for reactivity fluctuations caused by DNPs flowing with the fuel.The control rod operates passively by leveraging the combined effects of gravity,buoyancy,and fluid dynamic forces,thereby eliminating the need for an external drive mechanism and enabling direct integration within the active region of the core.Using a 150 MWt thorium-based molten salt reactor as the reference design,we develop a mathematical model to systematically analyze the effects of key parameters—including the geometric dimensions and density of the SCR—on its performance.We examine its motion characteristics under different core flow conditions and assess its feasibility for the dynamic compensation of reactivity changes caused by fuel flow.The results of this study demonstrate that the SCR can effectively counteract reactivity fluctuations induced by fuel flow within molten salt reactors.A sensitivity analysis reveals that the SCR’s average density exerts a profound impact on its start-up flow threshold,channel flow rate,resistance to fuel density fluctuations,and response characteristics.This underscores the critical need to optimize this parameter.Moreover,by judiciously selecting the SCR’s length,number of deployed units,and the placement we can achieve the necessary reactivity control while maintaining a favorable balance between neutron economy and heat transfer performance.Ultimately,this paper provides an innovative solution for the passive reactivity control in molten salt reactors,offering significant potential for practical engineering applications.展开更多
The Mg−Al composite rods of aluminum core-reinforced magnesium alloy were prepared by the extrusion−shear(ES)process,and the microstructure,deformation mechanism,and mechanical properties of the Mg−Al composite rods w...The Mg−Al composite rods of aluminum core-reinforced magnesium alloy were prepared by the extrusion−shear(ES)process,and the microstructure,deformation mechanism,and mechanical properties of the Mg−Al composite rods were investigated at different extrusion temperatures and shear stresses.The experimental results show that the proportion of dynamic recrystallization(DRX)and texture for Al and Mg alloys are controlled by the combination of temperature and shear stress.The texture type of the Al alloys exhibits slight variations at different temperatures.With the increase of temperature,the DRX behavior of Mg alloy shifts from discontinuous DRX(DDRX),continuous DRX(CDRX),and twin-induced DRX(TDRX)dominant to CDRX,the dislocation density in Mg alloy grains decreases significantly,and the average value of Schmid factor(SF)of the basalslip system increases.In particular,partial grains exhibit a distinct dominant slip system at 390℃.The hardness and thickness of the bonding layer,as well as the yield strength and elongation of the Mg alloy,reach their maximum at 360℃as a result of the intricate influence of the combined temperature and shear stress.展开更多
Compared with noble metals, improving the sensitivity of semiconducting surface-enhanced Raman scattering(SERS) substrates is of great significance to their fundamental research and practical application of Raman spec...Compared with noble metals, improving the sensitivity of semiconducting surface-enhanced Raman scattering(SERS) substrates is of great significance to their fundamental research and practical application of Raman spectroscopy. Herein, a simple chemical method is developed to synthesize a rhenium trioxide(ReO_(3)) microtubes assembled with highly crystalline nanoparticles. The ReO_(3) microtubes show a strong and well-defined surface plasmon resonance(SPR) behavior in visible region, which is rare for non-noble metals. As a low-cost SERS substrate, the plasmonic ReO_(3) microtubes exhibit a Raman enhancement factor of 8.9×10^(5) and a lowest detection limit of 1.0×10^(-9) mol/L for phenolic pollutants. Moreover, these ReO_(3) microtubule SERS substrates show excellent chemical stability and can resist the corrosion of strong acids and bases.展开更多
h-BN rods modified low-carbon alumina-carbon(Al_(2)O_(3)-C)refractories were prepared,and the effect of h-BN rod addition on the high-temperature properties was investigated and compared with commercial h-BN flake,car...h-BN rods modified low-carbon alumina-carbon(Al_(2)O_(3)-C)refractories were prepared,and the effect of h-BN rod addition on the high-temperature properties was investigated and compared with commercial h-BN flake,carbon black,and carbon nanotubes additives.The results demonstrated that Al_(2)O_(3)-C refractories containing h-BN rods exhibited optimal high-temperature service performances,including 25%higher hot modulus of rupture,21.3%higher thermal shock strength residual ratio,20.9%lower in oxidation and 44.3%less in slag corrosion,compared to the counterpart specimens without additives.Moreover,benefiting from the synergistic enhancement of the rod-like h-BN and in-situ generated SiC whiskers,the high-temperature service performances of h-BN rods containing specimens outperformed counterpart specimens containing commercial h-BN flake,carbon black,and carbon nanotubes,respectively.展开更多
The numerical simulation of the fluid flow and the flexible rod(s)interaction is more complicated and has lower efficiency due to the high computational cost.In this paper,a semi-resolved model coupling the computatio...The numerical simulation of the fluid flow and the flexible rod(s)interaction is more complicated and has lower efficiency due to the high computational cost.In this paper,a semi-resolved model coupling the computational fluid dynamics and the flexible rod dynamics is proposed using a two-way domain expansion method.The gov-erning equations of the flexible rod dynamics are discretized and solved by the finite element method,and the fluid flow is simulated by the finite volume method.The interaction between fluids and solid rods is modeled by introducing body force terms into the momentum equations.Referred to the traditional semi-resolved numerical model,an anisotropic Gaussian kernel function method is proposed to specify the interactive forces between flu-ids and solid bodies for non-circle rod cross-sections.A benchmark of the flow passing around a single flexible plate with a rectangular cross-section is used to validate the algorithm.Focused on the engineering applications,a test case of a finite patch of cylinders is implemented to validate the accuracy and efficiency of the coupled model.展开更多
The bimetallic composite rods prepared by co-extrusion have good mechanical properties,but their compressive deformation behaviors have rarely been studied.This paper primarily investigates the compressive deformation...The bimetallic composite rods prepared by co-extrusion have good mechanical properties,but their compressive deformation behaviors have rarely been studied.This paper primarily investigates the compressive deformation behavior of the AZ31/Mg-Gd-Y composite rod,analyzes the differences between its compressive deformation behavior and that of AZ31,and systematically studies the compressive deformation mechanisms of various regions in the composite rod,as well as the texture evolution and{10-12}twin evolution during the compression process.The results reveal that the AZ31/Mg-Gd-Y composite rods exhibit excellent metallurgical bonding,with the interface remaining intact even under a 9%compressive strain.In the compression process,AZ31 initiates yielding earlier than the AZ31/Mg-Gd-Y composite rods,exhibiting a relatively lower yield strength,whereas both show comparable plasticity.The deformation behavior of the AZ31/Mg-Gd-Y composite rod is governed by a combination of basal a slip and{10-12}-1011 tension twinning during compression along the ED(extrusion direction).With increasing compressive strain,the number of{10-12}twins in the AZ31 region(A/G-AZ31)of the AZ31/Mg-Gd-Y composite rod increases significantly,leading to changes in grain orientation,whereas the Mg-Gd-Y region(A/G-Mg-Gd-Y)of the composite rod shows no significant change.In addition,the A/G-Mg-Gd-Y significantly inhibits the nucleation and growth of{10-12}twins in A/G-AZ31 during compression,and thus the texture hardening generated by{10-12}twins make the work hardening behavior of the AZ31/Mg-Gd-Y composite rods different from that of AZ31.展开更多
To ensure the safe transportation of radioactive materials,numerous countries have established specific standards.For the transfer of fissile materials,it is imperative that the material within the packaging remains i...To ensure the safe transportation of radioactive materials,numerous countries have established specific standards.For the transfer of fissile materials,it is imperative that the material within the packaging remains in a subcritical state during routine,normal,and accidental transport conditions.In the event of an accident,the rods within the storage tank may become rearranged,introducing uncertainty that must be accounted for to ensure that criticality analysis results are conservative.Historically,this uncertainty was addressed overly conservatively due to limited research on non-uniform arrangement scenarios,which proved unsuitable for criticality safety analysis of spent fuel packages.This paper introduced three distinct methods to non-uniformly rearrange fuel rods—Uniform Arrangement by Blocks,Layer-by-Layer Determination,and Birdcage Deformation—and meticulously evaluates the influences of rod rearrangement on the effective multiplication factor of neutrons,k eff,utilizing the Monte Carlo method.Ultimately,this study presents a holistic method capable of encompassing the entire spectrum of potential effects stemming from the rearrangement of fuel rods during rods mispositioning accident.By augmenting the safety margin,this approach proves to be adeptly suited for the criticality safety analysis of nuclear fuel transport containers.展开更多
The linear-polarization optical property of CdSe quantum rods is studied in the framework of effectivemass envelope function theory. The effects of shape and magnetic field on the linear polarization factors are inves...The linear-polarization optical property of CdSe quantum rods is studied in the framework of effectivemass envelope function theory. The effects of shape and magnetic field on the linear polarization factors are investigated. It is found that CdSe quantum spheres have negative polarization factors （xy-polarized emission）and quantum long rods with small radius have positive linear polarization factors （z-polarized emission）. The z-direction is the direction of the c axis. Quantum long rods with large radius have negative linear polarization factors,due to the hexagonal crystal symmetry and the crystal field splitting energy. The linear polarization factors decrease and may change from a positive value to a negative value;i, e. ,the z-polarized emissions decrease relative to xy-polarized emissions as the magnetic field applied along the z direction increases.展开更多
This paper reports that pure hexagonal aluminium nitride microtubes and nanowires growing along the [0001] direction have been successfully synthesized by directly reacting AlCl3 with NaN3 at low temperature （450℃）...This paper reports that pure hexagonal aluminium nitride microtubes and nanowires growing along the [0001] direction have been successfully synthesized by directly reacting AlCl3 with NaN3 at low temperature （450℃） under condition of non-solvent system. The grey-white powder of reacting product was characterized by high-resolution transmission electron microscope （HRTEM）, which shows that the powder is long straight-wire morphology with outer diameter from 40nm to 300 nm and length up to several micrometres. The results of both electron diffraction （ED） and x-ray diffraction （XRD） indicate that the AlN microtubes have a pure hexagonal monocrystal tubular structure with the combination of the curled AlN nanobelts. Room-temperature photoluminescence spectrum of the synthesized sample showed an emission peak, which is closely related to the small size of the microtubes.展开更多
A newly natural fine template, kapok fiber, for microtube preparation was reported. Large scale microtubes with high length/diameter ratio and controllable wall thickness and morphology have been successfully fabricat...A newly natural fine template, kapok fiber, for microtube preparation was reported. Large scale microtubes with high length/diameter ratio and controllable wall thickness and morphology have been successfully fabricated with this template. It is a wildly available, low-cost, environmental friendly and fine structured natural template for microtubes. Its thin wall thickness is only about 1-2 um that means the whole template material is tiny and easy for removing. Even there is any residue the amount can be ignored. When the template is covered with a shell component, hollow structured microtube could be obtained by removing the thin inner template, and its shape could be the same as that of the original template （positive copy of the template＇s shape）. The products have high length/diameter ratio and uniform tubular structure. By further modifying the fabricating methods, facile fabrication not only exists for polypyrrole （PPy） in electrochemical deposition, but also for many other organic and inorganic materials. The surface morphology and wall thickness of the resultant microtubes can be easily modulated by controlling the processing conditions. This natural fiber is predicted to be a fine template for fabricating large scale microtubes with large cavity and high length/diameter ratio.展开更多
Unsteady wake from upstream components of landing gear impinging on downstream components could be a strong noise source.The use of a plane jet is proposed to reduce this flow-induced noise.Tandem rods with different ...Unsteady wake from upstream components of landing gear impinging on downstream components could be a strong noise source.The use of a plane jet is proposed to reduce this flow-induced noise.Tandem rods with different gap widths were utilized as the test body.Both acoustic and aerodynamic tests were conducted in order to validate this technique.Acoustic test results proved that overall noise emission from tandem rods could be lowered and tonal noise could be removed with use of the plane jet.However,when the plane jet was turned on,in some frequency range it could be the subsequent main contributor instead of tandem rods to total noise emission whilst in some frequency range rods could still be the main contributor.Moreover,aerodynamic tests fundamentally studied explanations for the noise reduction.Specifically,not only impinging speed to rods but speed and turbulence level to the top edge of the rear rod could be diminished by the upstream plane jet.Consequently,the vortex shedding induced by the rear rod was reduced,which was confirmed by the speed,Reynolds stress as well as the velocity fluctuation spectral measured in its wake.This study confirmed the potential use of a plane jet towards landing gear noise reduction.展开更多
On the basis of classical linear theory on longitudinal, torsional and flexural waves in thin elastic rods, and taking finite deformation and dispersive effects into consideration, three kinds of nonlinear evolution e...On the basis of classical linear theory on longitudinal, torsional and flexural waves in thin elastic rods, and taking finite deformation and dispersive effects into consideration, three kinds of nonlinear evolution equations are derived. Qualitative analysis of three kinds of nonlinear equations are presented. It is shown that these equations have homoclinic or heteroclinic orbits on the phase plane, corresponding to solitary wave or shock wave solutions, respectively. Based on the principle of homogeneous balance, these equations are solved with the Jacobi elliptic function expansion method. Results show that existence of solitary wave solution and shock wave solution is possible under certain conditions. These conclusions are consistent with qualitative analysis.展开更多
Free and steady-state forced longitudinal vibrations of non-uniform rods are investi- gated by an iteration method, which results in a series solution. The series obtained are convergent and linearly independent. Its ...Free and steady-state forced longitudinal vibrations of non-uniform rods are investi- gated by an iteration method, which results in a series solution. The series obtained are convergent and linearly independent. Its convergence is verified by convergence tests, its linear independence confirmed by the nonzero value of the corresponding Wronski determinant. Then, the solution obtained is an exact one reducible to a classical solution for the case of uniform rods. In order to verify the method, two examples are presented as an application of the proposed method. The results obtained are equivalent to the method in literature. In contrast to the proposed method ca- pable of dealing with arbitrary non-uniform rods in principle, the method in literature is confined to work on special cases.展开更多
In this study, a combined experimental, numerical and theoretical investigation is conducted on the penetration of semi-infinite 4340 steel targets by a homogeneous 93 W rod and two types of jacketed rods with strikin...In this study, a combined experimental, numerical and theoretical investigation is conducted on the penetration of semi-infinite 4340 steel targets by a homogeneous 93 W rod and two types of jacketed rods with striking velocities of 0.9-3.3 km/s. The results show that the jacketed rods produced typical“co-erosion” damage at all test velocities, except for the 93 W/1060 Al jacketed rod, which switched from an early “bi-erosion” damage to later “co-erosion” damage at a striking velocity of 936 m/s. However, the homogeneous 93 W rod always forms a large mushroom head during the penetration process. The damage mechanisms of these two types of jacketed rods differ for striking velocities of 0.9-2.0 km/s, but this difference gradually decreases with increased striking velocity. For velocities of 2.0-3.3 km/s, all three types of projectiles exhibit typical hydrodynamic penetration characteristics, and the damage mechanisms of the two types of jacketed rods are almost identical. For the same initial kinetic energy, the penetration performance of the jacketed rods is distinctly superior to that of the homogeneous 93 W rods.Compared with jacket density, jacket strength shows a more significant influence on the damage mechanism and penetration performance of the jacketed rod. Finally, an existing theoretical prediction model of the penetration depth of jacketed rods on semi-infinite targets in the co-erosion mode is modified. It transpires that-in terms of penetration depth-the modified theoretical model is in good agreement with the experimental and numerical observations for 93 W/TC4 and 93 W/1060 Al jacketed rods penetrating semi-infinite 4340 steel targets.展开更多
Starling with the L- and D,L-lactide copolymer (L:DL = 9:1) [P(L-DL)LA] of M-W = 32.1 x 10(4), rods were obtained through a two stage process: (1) melt-extrusion at 155 degreesC, and (2) hot-drawing at 90 degreesC to ...Starling with the L- and D,L-lactide copolymer (L:DL = 9:1) [P(L-DL)LA] of M-W = 32.1 x 10(4), rods were obtained through a two stage process: (1) melt-extrusion at 155 degreesC, and (2) hot-drawing at 90 degreesC to various drawing ratios. The molecular weight of P(L-DL)LA fell to 9.3 x 10(4) as a consequence of the production process. The crystallization and molecular orientation of P(L-DL)LA developed as a result of the hot-drawing. The mechanical strengths of the rods increase with the drawing ratio; The maximum for tensile strength, bending strength, bending modulus, and shear strength are 329 MPa, 237 MPa, 8.8 GPa, and 157 MPa, respectively.展开更多
Chronic inflammation associated with hepatitis C virus(HCV) infection can lead to disabling liver diseases with progression to liver cirrhosis and hepatocellular carcinoma. Despite the recent availability of more effe...Chronic inflammation associated with hepatitis C virus(HCV) infection can lead to disabling liver diseases with progression to liver cirrhosis and hepatocellular carcinoma. Despite the recent availability of more effective and less toxic therapeutic options, in most parts of the world the standard treatment consists of a weekly injection of pegylated interferon α(IFN-α) together with a daily dose of ribavirin. HCV patients frequently present circulating non-organ-specific autoantibodies demonstrating a variety of staining patterns in the indirect immunofluorescence assay for antinuclear antibodies(ANA). Between 20% to 40% of HCV patients treated with IFN-α and ribavirin develop autoantibodies showing a peculiar ANA pattern characterized as rods and rings(RR) structures. The aim of this article is to review the recent reports regarding RR structures and anti-rods/rings(antiRR) autoantibody production by HCV patients after IFN-α/ribavirin treatment. Anti-RR autoantibodies first appear around the sixth month of treatment and reach a plateau around the twelfth month. After treatment completion, anti-RR titers decrease/disappear in half the patients and remain steady in the other half. Some studies have observed a higher frequency of anti-RR antibodies in relapsers, i.e., patients in which circulating virus reappears after initially successful therapy. The main target of anti-RR autoantibodies in HCV patients is inosine-5'-monophosphate dehydrogenase 2(IMPDH2), the rate-limiting enzyme involved in the guanosine triphosphate biosynthesis pathway. Ribavirin is a direct IMPDH2 inhibitor and is able to induce the formation of RR structures in vitro and in vivo. In conclusion, these observations led to the hypothesis that anti-RR autoantibody production is a human model of immunologic tolerance breakdown that allows us to explore the humoral autoimmune response from the beginning of the putative triggering event: exposure to ribavirin and interferon.展开更多
A theoretical study is presented herein on the pen- etration of a semi-infinite target by a spherical-headed long rod for Yp 〉 S, where Yp is the penetrator strength and S is the static target resistance. For Yp 〉 S...A theoretical study is presented herein on the pen- etration of a semi-infinite target by a spherical-headed long rod for Yp 〉 S, where Yp is the penetrator strength and S is the static target resistance. For Yp 〉 S, depending upon initial impact velocity, there exist three types of penetration, namely, penetration by a rigid long rod, penetration by a deforming non-erosive long rod and penetration by an erosive long rod. If the impact velocity of the penetrator is higher than the hydrodynamic velocity （VH）, it will penetrate the target in an erosive mode; if the impact velocity lies between the hydrodynamic velocity （VH） and the rigid body velocity （VR）, it will penetrate the target in a deformable mode; if the impact velocity is less than the rigid body velocity （VR）, it will penetrate the target in a rigid mode. The critical conditions for the transition among these three penetration modes are proposed. It is demonstrated that the present model predictions correlate well with the experimental observations in terms of depth of penetration （DOP） and the critical transition conditions.展开更多
Based on the nonlinear geometric theory of extensible rods, an exact mathematical model of thermal post_buckling behavior of uniformly heated elastic rods with axially immovable ends is developed, in which the arc len...Based on the nonlinear geometric theory of extensible rods, an exact mathematical model of thermal post_buckling behavior of uniformly heated elastic rods with axially immovable ends is developed, in which the arc length s(x) of axial line and the longitudinal displacement u(x) are taken as the basic unknown functions. This is a two point boundary value problem of first order ordinary differential equations with strong non_linearity. By using shooting method and analytical continuation, the nonlinear boundary value problems are numerically solved. The thermal post_buckled states of the rods with transversely simply supported and clamped ends are obtained respectively and the corresponding numerical data tables and characteristic curves are also given.展开更多
It is obvious that the pressure gradient along the axial direction in a pipe flow keeps constant according to the Hagen-Poiseuille equation. However, recent experiments indicated that the distribution of the pressure ...It is obvious that the pressure gradient along the axial direction in a pipe flow keeps constant according to the Hagen-Poiseuille equation. However, recent experiments indicated that the distribution of the pressure seemed no longer linear for liquid flows in microtubes driven by high pressure （1-30MPa）. Based on H-P equation with slip boundary condition and Bridgman＇s relation of viscosity vs. static pressure, the nonlinear distribution of pressure along the axial direction is analyzed in this paper. The revised standard Poiseuille number with the effect of pressure-dependent viscosity taken into account agrees well with the experimental results. Therefore, the dependence of the viscosity on the pressure is one of the dominating factors under high driven pressure, and is represented by an important property coefficient α of the liquid.展开更多
Structural deterioration in the roof in an underground mine can easily cause roof fall,and deterioration is difficult to detect.When drilling holes for roof bolts,there is a relationship between the vibration of the d...Structural deterioration in the roof in an underground mine can easily cause roof fall,and deterioration is difficult to detect.When drilling holes for roof bolts,there is a relationship between the vibration of the drill rod and the properties of the rock being drilled.This paper analyzes transverse,longitudinal,and torsional vibrations in the drill rod by using vibration theory.Characteristic indexes for three kinds of vibration are determined.Using the finite element analysis software ABAQUS,a model for drill rod vibration during the drilling of roof bolt holes was established based on the geological and mining conditions in the Guyuan Coal Mine,northern China.Results from the model determined that the transverse and the longitudinal vibration decrease as the rock hardness decreases.In descending order,sandstone,sandy mudstone,mudstone,and weak interbeds cause progressively less vibration when being drilled.The ranking for strata that cause decreasing torsional vibration is slightly different,being,in descending order,mudstone,sandstone,sandy mudstone,and weak interbeds.These results provide a theoretical basis for predicting dangerous roof conditions and the presence of weak interbeds to allow for adjusting bolt support schemes.展开更多
基金supported by Youth Innovation Promotion Association of Chinese Academy of Sciences(No.2020261)Strategic Priority Research Program of Chinese Academy of Sciences(No.XDA02010000)the Young Potential Program of Shanghai Institute of Applied Physics,Chinese Academy of Sciences(No.SINAP-YXJH-202412).
文摘Molten salt reactors,being the only reactor type among Generation Ⅳ advanced nuclear reactors that utilize liquid fuels,offer inherent safety,high-temperature,and low-pressure operation,as well as the capability for online fuel reprocessing.However,the fuel-salt flow results in the decay of delayed neutron precursors(DNPs)outside the core,causing fluctuations in the effective delayed neutron fraction and consequently impacting the reactor reactivity.Particularly in accident scenarios—such as a combined pump shutdown and the inability to rapidly scram the reactor—the sole reliance on negative temperature feedback may cause a significant increase in core temperature,posing a threat to reactor safety.To address these problems,this paper introduces an innovative design for a passive fluid-driven suspended control rod(SCR)to dynamically compensate for reactivity fluctuations caused by DNPs flowing with the fuel.The control rod operates passively by leveraging the combined effects of gravity,buoyancy,and fluid dynamic forces,thereby eliminating the need for an external drive mechanism and enabling direct integration within the active region of the core.Using a 150 MWt thorium-based molten salt reactor as the reference design,we develop a mathematical model to systematically analyze the effects of key parameters—including the geometric dimensions and density of the SCR—on its performance.We examine its motion characteristics under different core flow conditions and assess its feasibility for the dynamic compensation of reactivity changes caused by fuel flow.The results of this study demonstrate that the SCR can effectively counteract reactivity fluctuations induced by fuel flow within molten salt reactors.A sensitivity analysis reveals that the SCR’s average density exerts a profound impact on its start-up flow threshold,channel flow rate,resistance to fuel density fluctuations,and response characteristics.This underscores the critical need to optimize this parameter.Moreover,by judiciously selecting the SCR’s length,number of deployed units,and the placement we can achieve the necessary reactivity control while maintaining a favorable balance between neutron economy and heat transfer performance.Ultimately,this paper provides an innovative solution for the passive reactivity control in molten salt reactors,offering significant potential for practical engineering applications.
基金supported by the general project of the National Natural Science Foundation of China(No.52071042)Chongqing Natural Science Foundation Project,China(Nos.CSTB2023NSCQ-MSX0079,cstc2021ycjh-bgzxm0148)Graduate Student Innovation Program of Chongqing University of Technology,China(No.gzlcx20232008).
文摘The Mg−Al composite rods of aluminum core-reinforced magnesium alloy were prepared by the extrusion−shear(ES)process,and the microstructure,deformation mechanism,and mechanical properties of the Mg−Al composite rods were investigated at different extrusion temperatures and shear stresses.The experimental results show that the proportion of dynamic recrystallization(DRX)and texture for Al and Mg alloys are controlled by the combination of temperature and shear stress.The texture type of the Al alloys exhibits slight variations at different temperatures.With the increase of temperature,the DRX behavior of Mg alloy shifts from discontinuous DRX(DDRX),continuous DRX(CDRX),and twin-induced DRX(TDRX)dominant to CDRX,the dislocation density in Mg alloy grains decreases significantly,and the average value of Schmid factor(SF)of the basalslip system increases.In particular,partial grains exhibit a distinct dominant slip system at 390℃.The hardness and thickness of the bonding layer,as well as the yield strength and elongation of the Mg alloy,reach their maximum at 360℃as a result of the intricate influence of the combined temperature and shear stress.
基金financial support from the National Natural Science Foundation of China(No.51771175)the Science Foundation of State Administration of market supervision(No.2021MK164)。
文摘Compared with noble metals, improving the sensitivity of semiconducting surface-enhanced Raman scattering(SERS) substrates is of great significance to their fundamental research and practical application of Raman spectroscopy. Herein, a simple chemical method is developed to synthesize a rhenium trioxide(ReO_(3)) microtubes assembled with highly crystalline nanoparticles. The ReO_(3) microtubes show a strong and well-defined surface plasmon resonance(SPR) behavior in visible region, which is rare for non-noble metals. As a low-cost SERS substrate, the plasmonic ReO_(3) microtubes exhibit a Raman enhancement factor of 8.9×10^(5) and a lowest detection limit of 1.0×10^(-9) mol/L for phenolic pollutants. Moreover, these ReO_(3) microtubule SERS substrates show excellent chemical stability and can resist the corrosion of strong acids and bases.
基金support from the National Natural Science Foundation of China(Grant Nos.52072274,52272021,U23A20559 and 52232002)the Open Foundation of State Key Laboratory of Advanced Refractories(No.SKLAR202207)+1 种基金the Key Laboratory of Hubei Province for Coal Conversion and New Carbon Materials(Wuhan University of Science and Technology,WKDM202201)the Open/Innovation Foundation of Hubei Three Gorges Laboratory(SK232006).
文摘h-BN rods modified low-carbon alumina-carbon(Al_(2)O_(3)-C)refractories were prepared,and the effect of h-BN rod addition on the high-temperature properties was investigated and compared with commercial h-BN flake,carbon black,and carbon nanotubes additives.The results demonstrated that Al_(2)O_(3)-C refractories containing h-BN rods exhibited optimal high-temperature service performances,including 25%higher hot modulus of rupture,21.3%higher thermal shock strength residual ratio,20.9%lower in oxidation and 44.3%less in slag corrosion,compared to the counterpart specimens without additives.Moreover,benefiting from the synergistic enhancement of the rod-like h-BN and in-situ generated SiC whiskers,the high-temperature service performances of h-BN rods containing specimens outperformed counterpart specimens containing commercial h-BN flake,carbon black,and carbon nanotubes,respectively.
基金supported by Shanghai 2021“Science and Technology Innovation Action Plan”:Social Development Science and Technology Research Project(Grant No.21DZ1202703).
文摘The numerical simulation of the fluid flow and the flexible rod(s)interaction is more complicated and has lower efficiency due to the high computational cost.In this paper,a semi-resolved model coupling the computational fluid dynamics and the flexible rod dynamics is proposed using a two-way domain expansion method.The gov-erning equations of the flexible rod dynamics are discretized and solved by the finite element method,and the fluid flow is simulated by the finite volume method.The interaction between fluids and solid rods is modeled by introducing body force terms into the momentum equations.Referred to the traditional semi-resolved numerical model,an anisotropic Gaussian kernel function method is proposed to specify the interactive forces between flu-ids and solid bodies for non-circle rod cross-sections.A benchmark of the flow passing around a single flexible plate with a rectangular cross-section is used to validate the algorithm.Focused on the engineering applications,a test case of a finite patch of cylinders is implemented to validate the accuracy and efficiency of the coupled model.
基金supported by National Natural Science Foundation of China(52274397 and 52374395)Shandong Provincial Natural Science Foundation of China(ZR2024JQ020).
文摘The bimetallic composite rods prepared by co-extrusion have good mechanical properties,but their compressive deformation behaviors have rarely been studied.This paper primarily investigates the compressive deformation behavior of the AZ31/Mg-Gd-Y composite rod,analyzes the differences between its compressive deformation behavior and that of AZ31,and systematically studies the compressive deformation mechanisms of various regions in the composite rod,as well as the texture evolution and{10-12}twin evolution during the compression process.The results reveal that the AZ31/Mg-Gd-Y composite rods exhibit excellent metallurgical bonding,with the interface remaining intact even under a 9%compressive strain.In the compression process,AZ31 initiates yielding earlier than the AZ31/Mg-Gd-Y composite rods,exhibiting a relatively lower yield strength,whereas both show comparable plasticity.The deformation behavior of the AZ31/Mg-Gd-Y composite rod is governed by a combination of basal a slip and{10-12}-1011 tension twinning during compression along the ED(extrusion direction).With increasing compressive strain,the number of{10-12}twins in the AZ31 region(A/G-AZ31)of the AZ31/Mg-Gd-Y composite rod increases significantly,leading to changes in grain orientation,whereas the Mg-Gd-Y region(A/G-Mg-Gd-Y)of the composite rod shows no significant change.In addition,the A/G-Mg-Gd-Y significantly inhibits the nucleation and growth of{10-12}twins in A/G-AZ31 during compression,and thus the texture hardening generated by{10-12}twins make the work hardening behavior of the AZ31/Mg-Gd-Y composite rods different from that of AZ31.
文摘To ensure the safe transportation of radioactive materials,numerous countries have established specific standards.For the transfer of fissile materials,it is imperative that the material within the packaging remains in a subcritical state during routine,normal,and accidental transport conditions.In the event of an accident,the rods within the storage tank may become rearranged,introducing uncertainty that must be accounted for to ensure that criticality analysis results are conservative.Historically,this uncertainty was addressed overly conservatively due to limited research on non-uniform arrangement scenarios,which proved unsuitable for criticality safety analysis of spent fuel packages.This paper introduced three distinct methods to non-uniformly rearrange fuel rods—Uniform Arrangement by Blocks,Layer-by-Layer Determination,and Birdcage Deformation—and meticulously evaluates the influences of rod rearrangement on the effective multiplication factor of neutrons,k eff,utilizing the Monte Carlo method.Ultimately,this study presents a holistic method capable of encompassing the entire spectrum of potential effects stemming from the rearrangement of fuel rods during rods mispositioning accident.By augmenting the safety margin,this approach proves to be adeptly suited for the criticality safety analysis of nuclear fuel transport containers.
文摘The linear-polarization optical property of CdSe quantum rods is studied in the framework of effectivemass envelope function theory. The effects of shape and magnetic field on the linear polarization factors are investigated. It is found that CdSe quantum spheres have negative polarization factors （xy-polarized emission）and quantum long rods with small radius have positive linear polarization factors （z-polarized emission）. The z-direction is the direction of the c axis. Quantum long rods with large radius have negative linear polarization factors,due to the hexagonal crystal symmetry and the crystal field splitting energy. The linear polarization factors decrease and may change from a positive value to a negative value;i, e. ,the z-polarized emissions decrease relative to xy-polarized emissions as the magnetic field applied along the z direction increases.
基金Project supported by the National Natural Science Foundation of China （Grant No 10474078） and the Science Foundation of the Education 0ffice of Shanxi Province, China.
文摘This paper reports that pure hexagonal aluminium nitride microtubes and nanowires growing along the [0001] direction have been successfully synthesized by directly reacting AlCl3 with NaN3 at low temperature （450℃） under condition of non-solvent system. The grey-white powder of reacting product was characterized by high-resolution transmission electron microscope （HRTEM）, which shows that the powder is long straight-wire morphology with outer diameter from 40nm to 300 nm and length up to several micrometres. The results of both electron diffraction （ED） and x-ray diffraction （XRD） indicate that the AlN microtubes have a pure hexagonal monocrystal tubular structure with the combination of the curled AlN nanobelts. Room-temperature photoluminescence spectrum of the synthesized sample showed an emission peak, which is closely related to the small size of the microtubes.
基金supported by the National Natural Science Foundation of China(No.50821062)the National 973 Project(No.2005CCA00800).
文摘A newly natural fine template, kapok fiber, for microtube preparation was reported. Large scale microtubes with high length/diameter ratio and controllable wall thickness and morphology have been successfully fabricated with this template. It is a wildly available, low-cost, environmental friendly and fine structured natural template for microtubes. Its thin wall thickness is only about 1-2 um that means the whole template material is tiny and easy for removing. Even there is any residue the amount can be ignored. When the template is covered with a shell component, hollow structured microtube could be obtained by removing the thin inner template, and its shape could be the same as that of the original template （positive copy of the template＇s shape）. The products have high length/diameter ratio and uniform tubular structure. By further modifying the fabricating methods, facile fabrication not only exists for polypyrrole （PPy） in electrochemical deposition, but also for many other organic and inorganic materials. The surface morphology and wall thickness of the resultant microtubes can be easily modulated by controlling the processing conditions. This natural fiber is predicted to be a fine template for fabricating large scale microtubes with large cavity and high length/diameter ratio.
基金Project partially supported by the European Union FP7 Clean Sky Joint Technology Initiative“ALLEGRA”(Grant No.308225)
文摘Unsteady wake from upstream components of landing gear impinging on downstream components could be a strong noise source.The use of a plane jet is proposed to reduce this flow-induced noise.Tandem rods with different gap widths were utilized as the test body.Both acoustic and aerodynamic tests were conducted in order to validate this technique.Acoustic test results proved that overall noise emission from tandem rods could be lowered and tonal noise could be removed with use of the plane jet.However,when the plane jet was turned on,in some frequency range it could be the subsequent main contributor instead of tandem rods to total noise emission whilst in some frequency range rods could still be the main contributor.Moreover,aerodynamic tests fundamentally studied explanations for the noise reduction.Specifically,not only impinging speed to rods but speed and turbulence level to the top edge of the rear rod could be diminished by the upstream plane jet.Consequently,the vortex shedding induced by the rear rod was reduced,which was confirmed by the speed,Reynolds stress as well as the velocity fluctuation spectral measured in its wake.This study confirmed the potential use of a plane jet towards landing gear noise reduction.
基金Project supported by the National Natural Science Foundation of China (No.10772129)the Youth Science Foundation of Shanxi Province of China (No.2006021005)
文摘On the basis of classical linear theory on longitudinal, torsional and flexural waves in thin elastic rods, and taking finite deformation and dispersive effects into consideration, three kinds of nonlinear evolution equations are derived. Qualitative analysis of three kinds of nonlinear equations are presented. It is shown that these equations have homoclinic or heteroclinic orbits on the phase plane, corresponding to solitary wave or shock wave solutions, respectively. Based on the principle of homogeneous balance, these equations are solved with the Jacobi elliptic function expansion method. Results show that existence of solitary wave solution and shock wave solution is possible under certain conditions. These conclusions are consistent with qualitative analysis.
基金supported by the National Natural Science Foundation of China(Nos.11072157,11272219,11227201 and10932006)the Training Program for Leading Talent in University Innovative Research Team in Hebei Province(No.LJRC006)
文摘Free and steady-state forced longitudinal vibrations of non-uniform rods are investi- gated by an iteration method, which results in a series solution. The series obtained are convergent and linearly independent. Its convergence is verified by convergence tests, its linear independence confirmed by the nonzero value of the corresponding Wronski determinant. Then, the solution obtained is an exact one reducible to a classical solution for the case of uniform rods. In order to verify the method, two examples are presented as an application of the proposed method. The results obtained are equivalent to the method in literature. In contrast to the proposed method ca- pable of dealing with arbitrary non-uniform rods in principle, the method in literature is confined to work on special cases.
基金supported by the National Natural Science Foundation of China(Grant nos.:11672138,11602113)Foundation of National Key Lab.of Transient Physics(Grant no.:6142604180407,JCKYS2020606004).
文摘In this study, a combined experimental, numerical and theoretical investigation is conducted on the penetration of semi-infinite 4340 steel targets by a homogeneous 93 W rod and two types of jacketed rods with striking velocities of 0.9-3.3 km/s. The results show that the jacketed rods produced typical“co-erosion” damage at all test velocities, except for the 93 W/1060 Al jacketed rod, which switched from an early “bi-erosion” damage to later “co-erosion” damage at a striking velocity of 936 m/s. However, the homogeneous 93 W rod always forms a large mushroom head during the penetration process. The damage mechanisms of these two types of jacketed rods differ for striking velocities of 0.9-2.0 km/s, but this difference gradually decreases with increased striking velocity. For velocities of 2.0-3.3 km/s, all three types of projectiles exhibit typical hydrodynamic penetration characteristics, and the damage mechanisms of the two types of jacketed rods are almost identical. For the same initial kinetic energy, the penetration performance of the jacketed rods is distinctly superior to that of the homogeneous 93 W rods.Compared with jacket density, jacket strength shows a more significant influence on the damage mechanism and penetration performance of the jacketed rod. Finally, an existing theoretical prediction model of the penetration depth of jacketed rods on semi-infinite targets in the co-erosion mode is modified. It transpires that-in terms of penetration depth-the modified theoretical model is in good agreement with the experimental and numerical observations for 93 W/TC4 and 93 W/1060 Al jacketed rods penetrating semi-infinite 4340 steel targets.
文摘Starling with the L- and D,L-lactide copolymer (L:DL = 9:1) [P(L-DL)LA] of M-W = 32.1 x 10(4), rods were obtained through a two stage process: (1) melt-extrusion at 155 degreesC, and (2) hot-drawing at 90 degreesC to various drawing ratios. The molecular weight of P(L-DL)LA fell to 9.3 x 10(4) as a consequence of the production process. The crystallization and molecular orientation of P(L-DL)LA developed as a result of the hot-drawing. The mechanical strengths of the rods increase with the drawing ratio; The maximum for tensile strength, bending strength, bending modulus, and shear strength are 329 MPa, 237 MPa, 8.8 GPa, and 157 MPa, respectively.
基金Supported by Brazilian government research foundations National Council for Research and Technology and Coordination for the Improvement of Higher Education Personnel with research grant and scholarships processNo.9028-11-0+2 种基金No.305064/2011-8 and No.232711/2014-3Sao Paulo Government agency Sao Paulo State Research Foundation withprocess No.2011/12448-0both granted to Andrade LEC and Keppeke GD
文摘Chronic inflammation associated with hepatitis C virus(HCV) infection can lead to disabling liver diseases with progression to liver cirrhosis and hepatocellular carcinoma. Despite the recent availability of more effective and less toxic therapeutic options, in most parts of the world the standard treatment consists of a weekly injection of pegylated interferon α(IFN-α) together with a daily dose of ribavirin. HCV patients frequently present circulating non-organ-specific autoantibodies demonstrating a variety of staining patterns in the indirect immunofluorescence assay for antinuclear antibodies(ANA). Between 20% to 40% of HCV patients treated with IFN-α and ribavirin develop autoantibodies showing a peculiar ANA pattern characterized as rods and rings(RR) structures. The aim of this article is to review the recent reports regarding RR structures and anti-rods/rings(antiRR) autoantibody production by HCV patients after IFN-α/ribavirin treatment. Anti-RR autoantibodies first appear around the sixth month of treatment and reach a plateau around the twelfth month. After treatment completion, anti-RR titers decrease/disappear in half the patients and remain steady in the other half. Some studies have observed a higher frequency of anti-RR antibodies in relapsers, i.e., patients in which circulating virus reappears after initially successful therapy. The main target of anti-RR autoantibodies in HCV patients is inosine-5'-monophosphate dehydrogenase 2(IMPDH2), the rate-limiting enzyme involved in the guanosine triphosphate biosynthesis pathway. Ribavirin is a direct IMPDH2 inhibitor and is able to induce the formation of RR structures in vitro and in vivo. In conclusion, these observations led to the hypothesis that anti-RR autoantibody production is a human model of immunologic tolerance breakdown that allows us to explore the humoral autoimmune response from the beginning of the putative triggering event: exposure to ribavirin and interferon.
基金supported by the National Natural Science Foundation of China (10872195)
文摘A theoretical study is presented herein on the pen- etration of a semi-infinite target by a spherical-headed long rod for Yp 〉 S, where Yp is the penetrator strength and S is the static target resistance. For Yp 〉 S, depending upon initial impact velocity, there exist three types of penetration, namely, penetration by a rigid long rod, penetration by a deforming non-erosive long rod and penetration by an erosive long rod. If the impact velocity of the penetrator is higher than the hydrodynamic velocity （VH）, it will penetrate the target in an erosive mode; if the impact velocity lies between the hydrodynamic velocity （VH） and the rigid body velocity （VR）, it will penetrate the target in a deformable mode; if the impact velocity is less than the rigid body velocity （VR）, it will penetrate the target in a rigid mode. The critical conditions for the transition among these three penetration modes are proposed. It is demonstrated that the present model predictions correlate well with the experimental observations in terms of depth of penetration （DOP） and the critical transition conditions.
文摘Based on the nonlinear geometric theory of extensible rods, an exact mathematical model of thermal post_buckling behavior of uniformly heated elastic rods with axially immovable ends is developed, in which the arc length s(x) of axial line and the longitudinal displacement u(x) are taken as the basic unknown functions. This is a two point boundary value problem of first order ordinary differential equations with strong non_linearity. By using shooting method and analytical continuation, the nonlinear boundary value problems are numerically solved. The thermal post_buckled states of the rods with transversely simply supported and clamped ends are obtained respectively and the corresponding numerical data tables and characteristic curves are also given.
基金The project supported by the Chinese Academy of Sciences Major Innovation Project (KJCX2-SW-L2)the National Natural Science Foundation of China (10272107)The English text was polished by Yunming Chen
文摘It is obvious that the pressure gradient along the axial direction in a pipe flow keeps constant according to the Hagen-Poiseuille equation. However, recent experiments indicated that the distribution of the pressure seemed no longer linear for liquid flows in microtubes driven by high pressure （1-30MPa）. Based on H-P equation with slip boundary condition and Bridgman＇s relation of viscosity vs. static pressure, the nonlinear distribution of pressure along the axial direction is analyzed in this paper. The revised standard Poiseuille number with the effect of pressure-dependent viscosity taken into account agrees well with the experimental results. Therefore, the dependence of the viscosity on the pressure is one of the dominating factors under high driven pressure, and is represented by an important property coefficient α of the liquid.
基金the National Natural Science Foundation of China(Nos.51104055,51274087,51604094 and 51674098)
文摘Structural deterioration in the roof in an underground mine can easily cause roof fall,and deterioration is difficult to detect.When drilling holes for roof bolts,there is a relationship between the vibration of the drill rod and the properties of the rock being drilled.This paper analyzes transverse,longitudinal,and torsional vibrations in the drill rod by using vibration theory.Characteristic indexes for three kinds of vibration are determined.Using the finite element analysis software ABAQUS,a model for drill rod vibration during the drilling of roof bolt holes was established based on the geological and mining conditions in the Guyuan Coal Mine,northern China.Results from the model determined that the transverse and the longitudinal vibration decrease as the rock hardness decreases.In descending order,sandstone,sandy mudstone,mudstone,and weak interbeds cause progressively less vibration when being drilled.The ranking for strata that cause decreasing torsional vibration is slightly different,being,in descending order,mudstone,sandstone,sandy mudstone,and weak interbeds.These results provide a theoretical basis for predicting dangerous roof conditions and the presence of weak interbeds to allow for adjusting bolt support schemes.
